Wall-mount vanity M 2418 WM – 1 drawer – 24” length21 7/8’’ depth x 23 9/16’’ length x 18’’ height – 557 x 598 x 457 mm
M Collection Wall-mount vanity18’’ height
Furniture
n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawers
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
Drawers configuration
Horseshoe
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
Cube Collection Lavatories_22” depth x 24” length x 2” height - 559 x 610 x 51 mm
Compatible Integrated Countertop for M 2418 WM vanity (countertop sold separately)
Ove Collection Integrated Countertop_22” depth x 24” length x 2” height - 559 x 610 x 51 mm
VOVS 24
VCS 24
Also compatible with the following WETSTYLE vessel sink models: VBE821A, VC815A, VC821A, VOV815A, VOV821A, VCR821A, VTP821A
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
Wall-mount vanity M 3018 WM – 1 drawer – 30” length21 7/8’’ depth x 28 7/8’’ length x 18’’ height – 557 x 759 x 457 mm
29 " [75.9cm]7|8
M3018 WM
29 " [75.9cm]7|
828 " [72.1cm]3|
8
M Collection Wall-mount vanity18’’ height
Furniture
n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawers
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
Drawers configuration
Horseshoe
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
Cube Collection Lavatories_22” depth x 30” length x 2” height - 559 x 762 x 51 mm
Compatible Integrated Countertop for M 3018 WM vanity (countertop sold separately)
VCS 30
Also compatible with the following WETSTYLE vessel sink models: VTP821A, VCR815A, VBE821A, VC815A, VC821A, VOV815A, VOV821A
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
Wall-mount vanity M 3618 WM – 1 drawer – 36” length21 7/8’’ depth x 35 5/8’’ length x 18’’ height – 557 x 905 x 457 mm
M Collection Wall-mount vanity18’’ height
Furniture
n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawers
n Drawer divider
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
Drawers configuration
3/4 deep
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
R04/13
VCS 36
VOVS 36
Ove Collection Lavatories_22” depth x 36” length x 2” height - 559 x 914 x 51 mm
Cube Collection Lavatories_22” depth x 36” length x 2” height - 559 x 914 x 51 mm
VCS 36R
VCS 36L
VCS 36C
Compatible Integrated Countertop for M 3618 WM vanity (countertop sold separately)
Also compatible with the following WETSTYLE vessel sink models: VBE821A, VC815A, VC821A, VOV815A, VOV821A, VCR821A, VTP821A
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
Wall-mount vanity M 4218 WM – 1 drawer – 42” length21 7/8’’ depth x 41 7/8’’ length x 18’’ height – 557 x 1064 x 457 mm
M4218 WM
41 " [106.4cm]7|
8
41 " [106.4cm]7|
840 " [102.6cm]3|
8
M Collection Wall-mount vanity18’’ height
Furniture
n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawer
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
Drawers configuration
3/4 deep**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
Cube Collection Lavatories_22” depth x 42” length x 2” height - 559 x 1069 x 51 mm
Compatible Integrated Countertop for M 4218 WM vanity (countertop sold separately)
VCS 42
Also compatible with the following WETSTYLE vessel sink models: VTP821A, VCR821A, VBE821A, VC815A, VC821A, VC836A, VOV815A, VOV821A
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
Wall-mount vanity M 4818 WM – 2 drawers – 48” length21 7/8’’ depth x 47 5/8’’ length x 18’’ height – 557 x 1210 x 457 mm
M Collection Wall-mount vanity18’’ height
R04/13
Furniture
n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawer
n Drawer divider
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
Drawers configuration
3/4 deep**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
VCS 48
VCS 48R
VCS 48L
Cube Collection Integrated Lavatories_22” depth x 48” length x 2” height - 559 x 1219 x 51 mm
Compatible Integrated Countertop for M 4818 WM vanity (countertop sold separately)
R04/13
VOVS 48
Ove Collection Lavatories_22” depth x 48” length x 2” height - 559 x 1219 x 51 mm
Compatible Integrated Countertop for M 4818 WM vanity (countertop sold separately)
Also compatible with the following WETSTYLE vessel sink models: VBE821A, VBE836A, VC815A, VC821A, VC836A, VOV815A, VOV821A, VOV836A, VCR821A, VTP821A
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
Wall-mount vanity M 6018 WM – 2 drawers – 60” length21 7/8’’ depth x 60’’ length x 18’’ height – 557 x 1524 x 457 mm
M Collection Wall-mount vanity18’’ height
Furniture
n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawers
n Drawer divider
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
Drawers configuration
3/4 deep**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
VCS 60
VCS 60T
VCS 60R
VCS 60L
Cube Collection Lavatories_22” depth x 60 1/4” length x 2” height - 559 x 1530 x 51 mm
Compatible Integrated Countertop for M 6018 WM vanity (countertop sold separately)
Also compatible with the following WETSTYLE vessel sink models: VBE821A, VBE836A, VC815A, VC821A, VC836A, VC848A, VOV815A, VOV821A, VOV836A, VOV848A, VCR821A, VTP821A
22" [
55.9
cm]
6014" [153.0cm]
1718" [43.6cm]
515 16" [
15.2
cm]
33 8" [8.
6cm
]
4" [10.1cm]5214" [132.7cm]
2" [5
.1cm
]
5114" [130.1cm]
6014" [153.0cm]
side view
front view
plan view
4" [10.2cm]14" [35.6cm]
141316" [37.7cm]
4" [10.2cm]
4" [10.2cm]
Ø112" [Ø
3.8cm]
26" [66.1cm] 1718" [43.4cm]
22" [55.9cm]
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
Collection
Scale/Échelle
Version
VCS 60T3/4" = 1'-0"
Notes:
Model/Modèle
Cube - Série VCS 60
R.03/12Aet se réserve le droit d'effectuer des modifications sans préavis.
and reserves the right to make revisions without noticeWETSTYLE cannot be held responsible for any technical errors
WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glisséesConsulter la fiche technique pour plus d'informations.
Refer to technical sheet for more information.
Mesure approximative. Le manufacturier accepte une tolérence de ¼" (6.35mm)
Approximate measurement. The manufacturer accept ¼" (6.35mm) variance.
22" [
55.9
cm]
6014" [153.0cm]
1718" [43.6cm]
515 16" [
15.2
cm]
33 8" [8.
6cm
]
4" [10.1cm]5214" [132.7cm]
2" [5
.1cm
]
5114" [130.1cm]
6014" [153.0cm]
side view
front view
plan view
4" [10.2cm]14" [35.6cm]
141316" [37.7cm]
4" [10.2cm]
4" [10.2cm]
Ø112" [Ø
3.8cm]
26" [66.1cm] 1718" [43.4cm]
22" [55.9cm]
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
Collection
Scale/Échelle
Version
VCS 60T3/4" = 1'-0"
Notes:
Model/Modèle
Cube - Série VCS 60
R.03/12Aet se réserve le droit d'effectuer des modifications sans préavis.
and reserves the right to make revisions without noticeWETSTYLE cannot be held responsible for any technical errors
WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glisséesConsulter la fiche technique pour plus d'informations.
Refer to technical sheet for more information.
Mesure approximative. Le manufacturier accepte une tolérence de ¼" (6.35mm)
Approximate measurement. The manufacturer accept ¼" (6.35mm) variance.
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
R04/13
M Collection Wall-mount vanity18’’ height
FurnitureWall-mount vanity M 7218 WM – 3 drawers – 72” length
21 7/8’’ depth x 72’’ length x 18’’ height – 557 x 1829 x 457 mm
R08/13
71 34 " 182.2cm
217 8
"55
.6cm
18"
45.7
cm
23 1116 " 60.2cm
Drawer Faces
22 1516 " 58.2cm 22 15
16 " 58.2cm 22 1516 " 58.2cm
71 34 " 182.2cm
123 4
"32
.4cm
Dra
wer
Fac
es
4" 10.2cm
8" 20.3cm 18"
45.7
cm
11 516 " 28.7cm
8 516 " 21.1cm
11 516 " 28.7cmDrawers
21 78 " 55.6cm
Wall-mount vanity M 7218 WM
plan view
front view side view
Version
Collection M
Model/Modèle
R.0 (2013-08-14)
3/4" = 1'-0"
M 7218 WMScale/Échelle
Collection
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
(En.) Approximate measurement. The manufacturer accept ¼" (6.35mm) variance. Refer to technical sheet for more information.WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
(Fr.) Mesures approximatives. Le manufacturier accepte une tolérence de ¼" (6.35mm). Consulter la fiche technique pour plus d'informations.WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glissées et se réserve le droit d'effectuer des modifications sans préavis.
Notes:
71 34 " 182.2cm
217 8
"55
.6cm
18"
45.7
cm
23 1116 " 60.2cm
Drawer Faces
22 1516 " 58.2cm 22 15
16 " 58.2cm 22 1516 " 58.2cm
71 34 " 182.2cm
123 4
"32
.4cm
Dra
wer
Fac
es
4" 10.2cm
8" 20.3cm 18"
45.7
cm
11 516 " 28.7cm
8 516 " 21.1cm
11 516 " 28.7cmDrawers
21 78 " 55.6cm
Wall-mount vanity M 7218 WM
plan view
front view side view
Version
Collection M
Model/Modèle
R.0 (2013-08-14)
3/4" = 1'-0"
M 7218 WMScale/Échelle
Collection
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
(En.) Approximate measurement. The manufacturer accept ¼" (6.35mm) variance. Refer to technical sheet for more information.WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
(Fr.) Mesures approximatives. Le manufacturier accepte une tolérence de ¼" (6.35mm). Consulter la fiche technique pour plus d'informations.WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glissées et se réserve le droit d'effectuer des modifications sans préavis.
Notes:
71 34 " 182.2cm
217 8
"55
.6cm
18"
45.7
cm
23 1116 " 60.2cm
Drawer Faces
22 1516 " 58.2cm 22 15
16 " 58.2cm 22 1516 " 58.2cm
71 34 " 182.2cm
123 4
"32
.4cm
Dra
wer
Fac
es
4" 10.2cm
8" 20.3cm 18"
45.7
cm
11 516 " 28.7cm
8 516 " 21.1cm
11 516 " 28.7cmDrawers
21 78 " 55.6cm
Wall-mount vanity M 7218 WM
plan view
front view side view
Version
Collection M
Model/Modèle
R.0 (2013-08-14)
3/4" = 1'-0"
M 7218 WMScale/Échelle
Collection
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
(En.) Approximate measurement. The manufacturer accept ¼" (6.35mm) variance. Refer to technical sheet for more information.WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
(Fr.) Mesures approximatives. Le manufacturier accepte une tolérence de ¼" (6.35mm). Consulter la fiche technique pour plus d'informations.WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glissées et se réserve le droit d'effectuer des modifications sans préavis.
Notes:n 45 degree bevel cuts precluding the need for drawer hardware
n All natural wood veneer
n AWI rated level 5 marine grade finish for moisture resistance and durability (industry’s highest finishing class)
n Finished vanity interiors in addition to front and sides
n Solid maple dovetailed drawers
n Drawer divider
n Drawer within a drawer
n Slow closing ball bearing glides
n Vanity top comes fully finished. Can be pre-cut at factory, upon request, if ordered with a vcs/vovs sink.
n Special wall preparation recommendations: the distance between studs should not exceed 16’’. Each stud should be reinforced vertically by 2’’x 3’’ wooden studs and horizontally with 2’’x 6’’ wooden studs at a height of 30’’ all along the width of the vanity.
n finishes and colorsoaknatural wenge whiteblackstone harbour greycoffee beansmoked
walnutnaturalnatural no calicochocolate
premium woodtorrified eucalyptusmozambique
matte lacquer*whitestone harbour grey black
high gloss lacquer** white
Drawers configuration
3/4 deep**ATTENTION: High-Gloss finish on sides and drawer facade only. Bottom and interior in white mat. This finish should only be ordererd with an integrated countertop (vessel sink not recommended)
*ATTENTION: Vessel sink not recommended with this finish
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
Compatible Integrated Countertop for M 7218 WM vanity (countertop sold separately)
R02/18
WETSTYLE cannot be held responsible for any technical errors and reserves the right to make revisions without notice.
Approximate measurement. The manufacturer accepts ¼" (6.35mm) variance. www.WETSTYLE.COM - Montreal - Canada
Tel. 1 888.536.9001 - [email protected]
VCS 72T
VCS 72
Cube Collection Lavatories_22” depth x 72” length x 2” height - 559 x 1829 x 51 mm
72" [182.9cm]
20" [50.8cm]
22" [
55.9
cm]
55 8" [14
.3cm
]
8" [20.3cm] 8" [20.3cm]56" [142.2cm]
33 8" [8.
6cm
]
2" [5
.1cm
]
72" [182.9cm]
5514" [140.4cm]
side view
front view
plan view
4" [10.2cm] 4" [10.2cm]14" [35.6cm]
22" [55.9cm]
141316" [37.7cm]
20" [50.8cm]32" [81.3cm]
8" [20.3cm]
Ø158" [Ø4.2cm]
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
Collection
Scale/ÉchelleSérie
Version
VCS 72T3/4" = 1'-0"
Notes:Model/Modèle
Cube - Série VCS72T
R.03/12et se réserve le droit d'effectuer des modifications sans préavis.
and reserves the right to make revisions without noticeWETSTYLE cannot be held responsible for any technical errors
WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glisséesConsulter la fiche technique pour plus d'informations.
Refer to technical sheet for more information.
Mesure approximative. Le manufacturier accepte une tolérence de ¼" (6.35mm)
Approximate measurement. The manufacturer accept ¼" (6.35mm) variance.
72" [182.9cm]
18" [45.7cm]
22" [
55.9
cm]
8" [20.3cm] 8" [20.3cm]20" [50.8cm]
33 8" [8.
6cm
]
2" [5
.1cm
]
72" [182.9cm]
5514" [140.4cm]
side view
front view
plan view
4" [10.2cm] 4" [10.2cm]14" [35.6cm]
22" [55.9cm]
141316" [37.7cm]
18" [45.7cm]36" [91.4cm]
8" [20.3cm]
55 8" [14
.3cm
]
Ø112 " [Ø3.8cm]
16" [40.6cm]
20" [50.8cm]16" [40.6cm]
www.WETSTYLE.ca - Montreal - CanadaTel. 450.536.9000 - 1 888.536.9001 - Fax. 450.536.0202
Collection
Scale/ÉchelleSérie
Version
VC 723/4" = 1'-0"
Notes:Model/Modèle
Cube - Série VC72
R.03/12Aet se réserve le droit d'effectuer des modifications sans préavis.
and reserves the right to make revisions without noticeWETSTYLE cannot be held responsible for any technical errors
WETSTYLE ne peut être tenu responsable des erreurs techniques qui pourraient s'y être glisséesConsulter la fiche technique pour plus d'informations.
Refer to technical sheet for more information.
Mesure approximative. Le manufacturier accepte une tolérence de ¼" (6.35mm)
Approximate measurement. The manufacturer accept ¼" (6.35mm) variance.
Also compatible with the following WETSTYLE vessel sink models: VBE821A, VBE836A, VC815A, VC821A, VC836A, VC848A, VOV815A, VOV821A, VOV836A, VOV848A, VCR821A, VTP821A
R08/13
Top Related