Download - FM and VHF Repeaters - NAPCO · REPEATERS for FM • Unidirectional ... The design of Fiplex’ DAS system was done based on the needs of the industry: robust architecture, flexibility

FM and VHF

Repeaters

REPEATERS for FM

• Unidirectional Amplifiers for indoor coverage of FM signals.

• Band Selective & Channel Selective versions.

• 80 and 90dB gain models.

• +24, +30 and +40dBm versions.

• IF SAW filtering technology, provides outstanding out

of band rejection

• FM Break In as optional for local SOS broadcasted

messages over FM channels.

• AGC and Overload protection.

• Antenna isolation control.

• Outdoor cabinet.

• Remote control capability (option RC-G).

• Fiber Feed capability (option FO-CT).

• Band Selective models:

• MF24V, 80dB gain, +24dBm

• HF30V, 80dB gain, +30dBm

• HF40V, 90dB gain, +40dBm

• Channelized models:

• MF24Cx 80dB gain, +24dBm, (replace “x” by channels qty)

• HF40Cx 90dB gain, +40dBm, (replace “x” by channels qty)

REPEATERS for VHF

• Repeater for Large size applications.

• Band Selective & Channel Selective versions.

• Band selective: 2MHz BW, software adjustable.

• Channel selective: 50KHz filter BW, software

adjustable.

• 5MHz min Tx to Rx separation.


of band rejection

• +24, +30 and +40dBm output power.

• 80dB gain adjustable.






• M124V, 80dB gain, +24dBm

• H130V, 80dB gain, +30dBm


• Channelized models:

• H140Cx, 80dB gain, +40dBm, (replace “x” by channels

number: 2, 4, 6 or 8)

BROADBAND REPEATERS for VHF

• Repeater for Large size applications.

• Channel Selective, full band.

• 50KHz BW channel filters, software programmable

• IF SAW filtering technology, provides outstanding out of band rejection

• Non-duplexed in/out ports

• +40dBm output power.






• Available models:

• HB140Cx, 80dB gain, +40dBm, (replace “x” by channels number: 2, 4, 6 or 8)

TETRA and UHF

Repeaters

• For P25, TETRA, IDAS, Mototrbo, Nexedge, MPT, CDMA450 and others.

• Repeater for Small and Medium size. applications.

• Single band as standard, multiband as optional.

• 2MHz and 5MHz BW (SW adjustable).


of band rejection

• 5MHz and 10MHz split.

• +18dBm and +24 dBm output power.




• Indoor cabinet as standard, outdoor cabinet available upon request.






Mid Power REPEATERS

High Power REPEATERS


• Repeater for Small and Medium size. applications.

• Single band as standard, multiband as optional.

• 2MHz and 5MHz BW (SW adjustable).


of band rejection

• 5MHz and 10MHz split.

• From +32 to +40dBm output power.












High Power Channel Selective REPEATERS


• Repeater for Large size applications, indoor and outdoor.

• From 2 channels and up.

• 50KHz BW.


of channel rejection

• +37 dBm.








• H436Cx, (replace “x” by channels number)

Cellular and

Public Safety 700 / 800MHz

Repeaters

C Series – Single Band

• Repeater for Medium Size applications.

• Single band.

• Band Selective (SAW filtered):

• Full band

• Narrow band: center frequency USB adjusted

• 65dB gain adjustable & +18/+20dBm output power.


of band rejection

• RSSI and Feedback indicators.



• Indoor cabinet.

• For LTE 700, LTE 800, PS700, PS800, 850MHz, EGSM, GSM-R, DCS, PCS, UMTS, AWS, LTE 2600.

• Compatible GSM, GPRS/EDGE, CDMA, 1X, WCDMA, HSDPA, HSUPA, LTE, TETRA, P25, and others.

C Series – Single Band


• C620-18, for LTE 700MHz A&B

• CL20-10, for LTE 700MHz C

• C720-12, for Public Safety 700MHz

• CS20-18, for SMR / Public Safety 800MHz

• C820-30, for LTE 800MHz

• CC20-25, for Cell 850MHz

• CR18-4, for GSM-R 900MHz

• CE18-35, for EGSM 900MHz

• CD18-75, for DCS 1800MHz

• CP20-60, for PCS 1900MHz

• CA20-55, for AWS

• CU20-60, for UMTS 2100MHz

• C218-70, for LTE 2.6GHz

• Only full band models listed, other BW available upon request.

C Series – Dual Band & Dual Sub Band

• Repeater for Medium Size applications.

• Dual Sub Band for single band, and Dual Band.


• Full band


• 65dB gain adjustable & +17dBm output power per band.


of band rejection




• Indoor cabinet.



• C7S1717-12-18, for Public Safety 700MHz + SMR / Public Safety 800MHz

• CCP1717-25-60, for Cell 850MHz + PCS

• CCU1717-25-60, for Cell 850MHz and UMTS 2100MHz

• CED1717-35-75, for EGSM 900MHz and DCS 1800MHz

• CC20-11-1.5, for Cell 850 A, A’ and A”

• CC20-10-2.5, for Cell 850 B and B’

• Other BW and mix of bands available upon request.

C Series – Dual Band & Dual Sub Band

H Series – Band Selective

• Repeater for Large Size applications.

• Single Band, Dual Sub Band and Dual Band.


• Full band



of band rejection

• 80dB gain adjustable & +27/+30/+37dBm output power.



• Indoor version as standard, outdoor available as optional

• For LTE 700, LTE 800, PS700, PS800, 850MHz, EGSM, GSM-R, DCS, PCS, UMTS, AWS, LTE 2600




H Series – Band Selective


• H627-18, for LTE 700MHz A&B, +27dBm output power

• HL30-10, for LTE 700MHz C, +30dBm output power

• H730-12, for Public Safety 700MHz, +30dBm output power

• HS30-18, for SMR / Public Safety 800MHz, +30dBm output power

• HS37-18, for SMR / Public Safety 800MHz , +37dBm output power

• HS40-18, for SMR / Public Safety 800MHz , +40dBm output power

• H830-30, for LTE 800MHz , +30dBm output power

• HC30-25, for Cell 850MHz , +30dBm output power

• HC37-25, for Cell 850MHz , +37dBm output power

• HC30-11-1.5, for Cell 850MHz , +30dBm output power




• HP27-60, for PCS 1900MHz , +27dBm output power

• HP37-60, for PCS 1900MHz , +37dBm output power

• HA27-55, for AWS , +27dBm output power

• HU27-60, for UMTS 2100MHz , +27dBm output power

• H227-70, for LTE 2.6GHz , +27dBm output power

• Only full band models listed, other BW available upon request.

H Series – Dual Band & Dual Sub Band


• Dual Sub Band for single Band, and Dual Band.


• Full band



of band rejection

• 80dB gain adjustable & +27/+34/+36dBm output power.



• Indoor version as standard, outdoor available as optional




H Series – Dual Band & Dual Sub Band


• H4S2430VV, for UHF + SMR / Public Safety 800MHz, +24dBm output power in UHF, +30dBm output power in SMR / Public Safety 800MHz

• H7S2727-12-18, for Public Safety 700MHz + SMR / Public Safety 800MHz, +27dBm per band.

• H7S3434-12-18, for Public Safety 700MHz + SMR / Public Safety 800MHz, +34dBm output power per band.

• HSC3434-18-25, for SMR / Public Safety 800MHz + Cell 850 , +34dBm output power per band.

• HCP2926-25-60, for Cell 850 + PCS, +29dBm output power in Cell 850 and +26dBm output power in PCS.

• HCP3636-25-60, for Cell 850 + PCS , +36dBm output power per band.

• HCP3636-11-1.5-60, for Cell 850 (A, A’& A”)+ PCS , +36dBm output power per band.

• Other BW and mix of bands available upon request.

H Series – Channel Selective


• Single and Dual band.

• For Public Safety 700MHz and SMR / Public Safety 800MHz

• Channel Selective (SAW filtered):

• From 2 channels and up, up to 20 per band

• 50KHz BW, software adjustable


of band rejection

• 80dB gain adjustable,

• +30 and +37dBm output power.




• Compatible with P25, TETRA, MPT1327 and others.


• DAS Fiber Feed capability (option FO-CT).

H Series – Channel Selective


• H730Cx, for Public Safety 700MHz, +30dBm output power (Replace “x” by channels number, up to 20 channels)

• H737Cx, for Public Safety 700MHz, +37dBm output power (Replace “x” by channels number, up to 20 channels)

• HS27Cx, for SMR / Public Safety 800MHz , +27dBm output power (Replace “x” by channels number, up to 20 channels)

• HS37Cx, for SMR / Public Safety 800MHz , +37dBm output power (Replace “x” by channels number, up to 20 channels)

• H7S2727C24, for Public Safety 700MHz + SMR / Public Safety 800MHz , +27dBm output power per band, 24 channels shared in both bands (factory defined)

• H7S3737C24, for Public Safety 700MHz + SMR / Public Safety 800MHz , +37dBm output power per band, 24 channels shared in both bands (factory defined)

Fiber DAS

Broadband – Neutral Host

50 – 2700MHz

FIBER DAS SOLUTIONS

Fiber DAS systems from FIPLEX offer a wide band “RF

over Fiber” solution that exceeds the need for indoor

and outdoor wide area coverage for any type of

telecommunications system in the ranges between

50MHz to 2700MHz.

The design of Fiplex’ DAS system was done based on

the needs of the industry: robust architecture,

flexibility, expandability, remote control…among others.

Its wide band design, along with high linearity and low

noise allows multiple systems to run in parallel, capable

of handling any mixture of analog and digital systems.

FIBER DAS ARCHITECTURE

The typical architecture of the Fiplex Fiber DAS solution

is composed of a Master Optical Unit (MOU) which is the

I/O point for the BTS thru a Point of Interconnection

(POI), and the Radio Head Units (RHU) that provides

the RF coverage into the service areas.

DAS topology is based on a STAR configuration where

all the RHU are directly connected to the MOU using a

single mono mode fiber optic link up to 20Kms in

length. Thanks to the built-in Wavelength Division

Multiplexers (WDM) there is no need to use two

separate fiber optic links, a single one handles DL and

UL simultaneously.

FIBER DAS ARCHITECTURE

POI

Fiplex POI (Point of Interconnection) is the first

component of a complete Fiber DAS System. POI

combines different signal sources (BTS, Node B,

BDAs) with duplexed ports, adjusts power levels, and

injects the combined downlinks and uplink bands into

the Master Optical Unit (MOU).

Different POIs are available that combine different

bands. Each POI is equipped with a single in/out port

per band. In case that more in/out ports are needed

per band, POI Ports Extenders must be used.

POI • Models

NUMBER OF INPUT PORTS PER BAND

Model VHF UHF LTE A,B LTE C PS700 PS800 850 PCS AWS

POI1001 1 1 1 1 1 1 1

POI1002 1 1 1 1 1 1

POI1003 1 1 1

POI1004 1 1

POI1005 1 1 1

POI1006 1 1 1 1

POI1007 1 1

POI1008 1 1

Model BAND INPUT PORTS

EPOI2001 VHF 4

EPOI2002 UHF 4

EPOI2003 700-2700 2 (SINGLE)

EPOI2004 700-2700 4 (SINGLE)

EPOI2005 700-2700 2 (DUAL)

EPOI2006 700-2700 4 (DUAL)

EPOI2007 700-2700 2 (TRIPLE)

EPOI2008 700-2700 4 (TRIPLE)

MASTER OPTICAL UNIT

Fiplex MOU is a broadband device that converts the RF

received, from the different BTS and/or Donor BDAs,

into light in the DL direction, and converts the light into

RF in the UL direction. It acts as a single I/O point for

the entire Fiber DAS, with the capability of handling

signals from 50Mhz to 2700MHz with high dynamic

range and low noise. Not only can BDA’s and BTS’s be

connected to the MOU, but it also supports MIMO

applications.

All the DAS components (MOU and RHUs) can be locally

and remotely controlled thru the MOU, via Ethernet or

GPRS (SNMP protocol). Additional alarm outputs are

available (LEDs and Dry Contacts)

MASTER OPTICAL UNIT • Features

• Broadband, 50MHz to 2.7GHz.

• 1310 and 1550uM, with built in WDM included.

• Capable of handling analog and digital signals (like

LTE, WCDMA, GSM, P25, TETRA, Mototrbo…)

• Automatic adjustment of FO link losses

• Independent gain adjustment per RHU

• Alarm outputs and DC backup input for redundancy

(NFPA)

• Connection to BTS, BDAs. Supports MIMO.

• Local and Remote control capability for MOU and RHU

• From 1 to 8 FO links as standard, expandable

• Models:

• MOU1x, replace “x” by optical outputs

MASTER OPTICAL UNIT • Models

Model number Number of RF Tx ports Number of RF Rx ports Optical I/O ports

MOU11 1 1 1

MOU12 1 1 2

MOU13 1 1 3

MOU14 1 1 4

MOU15 1 1 5

MOU16 1 1 6

MOU17 1 1 7

MOU18 1 1 8

MOU "X" "Y" (*) Replace X for value Replace X for value Replace Y for value

(*): Custom configuration, available upon request

REMOTE HEAD UNITS

Fiplex RHUs are band specific devices that receive the RF

over fiber from the MOU and convert to RF in order to

provide coverage for the service area. With the addition

of external combiners, multi-band applications can be

provided.

Covering from FM to LTE 2.6GHz, RHUs feature band

selective response with manual gain adjustment and

AGC.

Units are provided in IP65/NEMA 4 cabinets, and have

DC input power for battery backup, as well as I/O alarm

ports, making them NFPA compliant for Public Safety.

RHUs can be locally controlled via USB or via MOU, and

can be remotely controlled thru the MOU.

REMOTE HEAD UNITS • Features

• Available for FM, VHF, UHF, 700/800Mhz, Cell 850,

GSM 900, DCS, PCS, UMTS, AWS and all LTE band

• Single and Dual band units, with capability of

interconnection for multiband applications

• One single mode fiber, WDM built in

• From +18dBm to 37dBm output power

• Indoor and Outdoor cabinets

• Redundant FO link available as optional

• Management and configuration via USB or thru the

MOU

• Battery backup and alarm outputs (NFPA)

• Fullband and BW adjustable models

REMOTE HEAD UNITS • Models

Model Band / Freq. in MHz Downlink power, in dBm

MRHU-4 335 – 512 24

HRHU-4 335 – 512 37

LRHU-6 LTE A, B 18

MRHU-6 LTE A, B 27

LRHU-L LTE C 20

MRHU-L LTE C 30

LRHU-7 PS 700 20

MRHU-7 PS 700 30

HRHU-7 PS 700 37

LRHU-S SMR 800 / PS 800 20

MRHU-S SMR 800 / PS 800 30

HRHU-S SMR 800 / PS 800 37

LRHU-C CELL 850 20

MRHU-C CELL 850 30

HRHU-C CELL 850 37

LRHU-P PCS 20

MRHU-P PCS 30

HRHU-P PCS 37

LRHU-A AWS 20

HRHU-A AWS 35

Remote Control

Management Tool

FOMS – O&M Software

• Model: FOMS

• FIPLEX OMS: BDA Administrator System & BDA Control System.

• For Repeaters and DAS.

• Real-time.

• Server – client.

• Parameters and alarms.

• SNMP protocol.

• Remote connection thru Ethernet and wireless modem.

• Treeview.

• SQL database engine.

• Individual users profiles, permissions.

RC-G – Remote Control Unit

• Model: RC-G

• Unit that enables the remote control and supervision of Repeaters and DAS systems.

• Allows the remote control and supervision of DAS and Repeaters parameters and alarms.

• Communication via Ethernet and wireless modem.

• SNMP protocol.

• Factory installed.

• Works with FOMS platform.

Antennas and Passive Devices

Indoor Omni Antenna

• FIP1000

• Dome type.

• Roof mount.

• 700 – 2700MHz, suitable for GSM to WLAN.

• 3dBi gain.

• Vertical polarization, 55 degrees.

• Indoor type.

• N(f) connectors.

• Maximum power 100W.

Indoor Panel Antenna

• FIP2001

• Panel type.

• Wall mount.


• 8dBi gain.


• Horizontal aperture 68 degree.

• Front – Back ratio 15dB min.

• Indoor type.

• N(f) connectors.


Outdoor Panel Antenna

• FIP2004

• Panel type.

• Wall and Pipe mount.


• 7dBi gain.


• Horizontal aperture 87 degree.

• Front – Back ratio 20dB min.

• Outdoor type

• N(f) connectors


Coaxial Splitters

• PSC Series.

• 2, 3 and 4 ways.

• High power handling capability up to 500W.

• From VHF to 2700MHz

• 700-2700MHz broadband models.

• Low insertion loss.

• Low PIM, 160dBc typ.

• Indoor and outdoor versions.

• N(f) and 7/16(f) connectors.

• Models:

• PSC2-A2, VHF, 2 way



• PSC2-A2, UHF, 2 way



• PSC2-A2, 700-2700, 2 way

• PSC3-A2, 700-2700, 3 way

• PSC4-A2, 700-2700, 4 way

Broadband Splitters

• DPS Series.

• 2, 3 and 4 ways.

• Power handling capability as splitter of 50W.




• Indoor versions.

• N(f) type connectors.

• Models:

• DPS212, 2 way

• DPS312, 3 way

• DPS412, 4 way

RF Directional Couplers

• RSA Series.

• 6, 10, 15, 20 and 30dB coupling values.

• High power handling capability up to 200W.

• From VHF to 2700MHz




• Outdoor use.

• N(f) connectors

• Models:

• RSA2-A2J, VHF, 10dB

• RSA2-A2K, VHF, 6dB

• RSA2-B2J, UHF, 10dB

• RSA2-B2K, UHF, 6dB

• RSA2-W2J, 700-2700, 30dB

• RSA2-W2J, 700-2700, 20dB

• RSA2-W2J, 700-2700, 15dB

• RSA2-W2J, 700-2700, 10dB

• RSA2-W2J, 700-2700, 6dB