Installation
Put the hose in the middle of the coldjoint. The connection, ventilating hose /PREDIMAX / CEM has to be placedcompletely inside the concrete structure.
The hose has to be well set on the coldjoint and has to be fastened with hoseclamps at approx. 15 cm distance(depending on surface of the concreteof the construction joint).
BPA GmbHBehringstr. 1271083 Herrenberg-GültsteinGermany
Phone: +49 (0) 7032 - 893990Fax: +49 (0) 7032 - 8939929Web: www.dichte-bauwerke.deE-Mail: [email protected]
International References (Extract)
The injection ends have to be placed towards the outside ofthe formwork in order to be easily found again.Two different ways of installation are possible:
The overlapping should at least be10 cm.
Installation of the injection hose systemby using shutter connector includingrubber plate and a spider (for easyinstallation on the reinforcement).
Installing the ventilation hoses inside anend box:Important: Ventilation hoses have to befi xed in order to avoid a replacementduring the concrete work.
Hallandsås TunnelFörslöv/BåstadSweden
Variante di ValicoBarberino di Mugello/Sasso MarconiItaly
Turtmann TunnelTurtmannSwitzerland
Potsdamer PlatzBerlinGermany
Injection Hose System
PREDIMAX and CEM
Accessoires (Extract)
PREDIMAX injection hose is a paten-ted premium system with a General Building Code Test Certifi cate (abP). This double-jacketed PVC hose, which features offset openings for the release of compressed injection liquids, is used for the sealing of structural joints in undergroundstructures and tunnels.PREDIMAX injection hose is a twin layer system made up of an interior hose, with big outlets for the release of injection liquids, covered by an outer hose whose shell contains slots which are placed offset from the openings of the inner hose. This twin layer technology reliably inhibits fi nes from penetrating the inner shell of the PREDIMAX injection hose ensuring the free passage of the injection liquid into the concrete substrate.Successful Injections are possible even after years due to the smooth surface which doesn´t allow any sinter deposits or obstructions in the system.The unique PREDIMAX-technology allows for multiple injection even with cement!
Predimax 11 and 19 Injection Hose
Ventilation Hose
Hot-Shrinking Hose
Sprout/Nozzle
Sealing Plug
End Box
Shutter Connector, two-part
Plastic Connector 11
CEM injection tube is a budged-priced,high-capacity injection system. This sin-gle-walled tube based on PVC material with slightly cone-shaped openings and slots for the emersion of compressed injection material. The slots close auto-matically due to their special geometry thus avoiding effi ciently any penetration of cement paste from outside into the transport duct.
The injection tube with a General Buil-ding Code Test Certifi cate (abP) can be used for the sealing of construction joints in civil and underground engineering as well as in tunneling. The smooth surface of CEM injection tube effi ciently preventsany unwanted bonding between injection tube and concrete.CEM injection tube can be easily used for the injection with every favored injection material.
Successful Injections are possible even after years due to the smooth surface which doesn´t allow any sinter deposits or obstructions in the system.
CEM 11 and 19 Injection Tube
CEM 11 CEM 19
Dinternal 6 mm 11 mm
Dexternal 11 mm 19 mm
Material to be injected
Resins, acrylates, etc.
Resins, acrylates, micro fine cement, etc.
Product Characteristics
Multiple injections by using acrylic-gel
Multiple injections by using acrylic-gel or micro fine cement
Max. lenght of injection tube
10 m 20 m
PREDIMAX 11 PREDIMAX 19
Dinternal 6 mm 11 mm
Dexternal 11 mm 19 mm
Material to be injected
Resins, acrylates, fine cement, CEMproof cement lime, etc.
Resins, acrylates, fine cements, Ordinary Portland Cement, etc.
Product Characteristics
Multiple Injection
Multiple Injection
Max. length of injection hose
12 m 15 m
Top Related