Download - ENE040607000079 WCDMA BTS3900 Hardware Structure Issue1.0

7/30/2019 ENE040607000079 WCDMA BTS3900 Hardware Structure Issue1.0

1/55

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

www.huawei.com

Internal

WCDMA BTS3900

Hardware Structure

BTS3900V200R010

WRAN Training Team


2/55

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 2

As an important part of UTRAN,

NodeB mainly processes the signals of

physical layer of Uu interface

BTS3900 is a new generation indoor

marco NodeB which is produced by

Huawei Co. Ltd.


3/55


Upon completion of this course, you will be able to:

Master the hardware structure of BTS3900

Master the working principle of different subsystems and

boards of BTS3900

Master the cables connection rules of BTS3900

Know typical configurations of BTS3900


4/55


BTS3900 Product Description

BTS3900 Hardware Description


5/55


Chapter 1 NodeB Overview

Chapter 2 BTS3900 Hardware Structure

Chapter 3 BTS3900 Typical Configuration


6/55


Abbreviations

WMPT WCDMA Main Processing and Transmission Unit

WBBPa WCDMA Baseband Process unit Type A

WRFU WCDMA Radio Filter Unit

UBFA Universal BBU Fan Unit Type A

UEIU Universal Environment Interface unit

UELP Universal E1/T1 Lighting Protection unit

UFLP Universal FE/GE Lighting Protection unitUPEU Universal Power and Environment Interface Unit

UAEU Universal ATM over E1/T1 Interface and Processing Unit

UIEU Universal IP Packet over E1/T1 Interface and Processing Unit

UTRP Universal Transmission Processing Unit

DCDU-01 Direct Current Distribution Unit-01

CPRI Common Protocol Radio Interface

PSU The power supply unit

PMU The power and environment monitoring unit

APM Advanced Power Module


7/55HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 7

NodeB Position in UMTS Network

Iu-BC

RNC

RNC

NodeB

NodeB

NodeB

CS

PS

CBC

UE UTRAN CN

Uu IuIu-CS

Iu-PS

Iu-BC

Iur

Iub

Iub


8/55


NodeB System Architecture

Environment

Monitoring

device

Iub

Uu

UE

RNC

BTS3900 cabinet

O&M terminal

BTS3900 System

power supply

system

GPS antenna & feeder system

Clock synchronization source

Internal Clock

Antenna & feeder

subsystem

Transmission

deviceDDF


9/55






10/55



Section 1 BTS3900 Introduction

Section 2 BBU Modules Structure

Section 3 RF Modules Structure

Section 4 Power Modules Structure

Section 5 BTS3900 Cables


11/55


BTS3900 Appearance

Type Parameters

Dimensions 600(W)*900(H)*450(D)

Empty cabinet 70kg

Weight under full

configuration

160Kg

3*1 and 3*2 Weight 120Kg

- 48V : Input range ofvoltage

-38.4V DC to -57V DC

+24V: Input range ofvoltage

+21.6 V DC to +29 V DC

200 V AC to 240 V AC 200 V AC to 240 V AC 176 V AC to

290 V AC, single-phase

200 V AC/346 V AC to240 V AC/415V AC

176 V AC/304 V AC to 290 V AC/500V AC, three-phase

Working Temperature -20+50


12/55


BTS3900 Single Cabinet Full Configuration Structure

+ 24VDC

Single Cabinet

220V AC

Single Cabinet- 48VDC

Single Cabinet

1U

9U

2U

1U

1U

19U

2U

2U

1U


13/55


BTS3900 Stacked Cabinets Full Configuration Structure

3U


14/55


BTS3900 Capacity and Characteristics

System capacity specifications:

BTS3900 can support up to: uplink 1536 CEs and downlink 1536 CEs

BTS3900 can support up to: 3*8 cells or 6*4 cells

Characteristics

Transmission Type: E1/T1, FE (electrical port ), FE (optical port ),

Networking mode: star, chain, tree, ring and hybrid

Synchronization clock sources: Iub interface clock, GPS, and internal clock

Handover types: softer handover, soft handover and hard handover

Services: CS services, PS services , mixed services and position services

Enhanced functionsRET , HSDPA , HSUPA phase II


15/55


BTS3900 Logical Structure

PSU

RF Module

DCDU

WRFU

RNC

Antenna

Iub

WRFU

BBU

Power

Module

Baseband Transmission

Control module

+24V/220V -48V

Signal Current


16/55









17/55


Logical Structure of the BBU3900 Module

TO WRFU

Clock modeSignaling

Processing

Operation&

MaintenancePower mode

E1/T1

FE

Transport

Interface

Transmission

Adaptation

Protocol

Processing

FPProcessing

Codling

Decoding Demodulation

Modulation

Interface

Module

Transport Subsystem Baseband Subsystem

Control Subsystem

External SubsystemOMC

CPRI

RNC

Power

Control

information


18/55


BBU3900 Module Introduction

Mandatory boards and modulesWMPT, WBBP, UBFA, and UPEU

The optional boards are the UELP, UFLP, UTRP, and UEIU.

Full configuration

Typical configuration


19/55


BBU3900 Module Introduction

Slot

16

Slot 18

Slot 19

SLOT0

SLOT1

SLOT2

SLOT3

SLOT4

SLOT5

SLOT6

SLOT7

Active and standby slot definition

only for UTRP board

B

FA

PEU/

EIU

PEU/

EIU

WBBP

WBBP

WBBP

WBBP

UTRP

UTRP

WMPT

WMPT

Slot boards definition

Board Slot 0 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7

WMPT available available

UTRP available available available available available available

WBBP available available available available available available

UELP available available

UFLP available available


20/55


BBU Module --- WMPT Board

Board number

maximum is 2 for one BBU

mandatory board

working in active andstandby

4E1:DB26

IP transmission on

Electrical Port :RJ45

IP transmissionOptical signals: SFP

GPS antenna: SMA

Commissioning:RJ45

Loading Testing:USB

LEDs

Main Functions

Providing OM functions

Controlling other boards in the system and

providing the reference clockProviding USB ports for automatic NodeB

upgraded

Providing transmission port for Iub interface

Providing OM channels


21/55



LEDs of running status of WMPT:

Label Color Status Description

RUN Green ON The board has power input, yet the board is faulty.OFF The board has no power input.

1s ON, 1s OFF The board is running as configured.

0.125s ON, 0.125s OFF The software is being loaded to the board, or the

board is not in use.

ALM Red ON The board is reporting hardware alarms.OFF The board is running properly.

ACT Green ON The board is in active mode.OFF The board is in standby mode.


22/55



LED Color Status Description

LEDs beside the

FE1 and FE0 optical

portGreen ON The connections are functional.

OFF The connections are faulty.

Yellow Blinking There is ongoing data transmission.

OFF There is no data transmission.

LEDs beside the

ETH port Green ON The connections are functional.OFF The connections are faulty.

Yellow Blinking There is ongoing data transmission.

OFF There is no data transmission.


23/55



Two DIP Switches :

SW1 for setting the E1/T1 working mode

SW2 for setting the protection ground for the E1.

Settings of SW1

Bit T1 Mode 120-ohm E1

Balanced Mode

75-ohm E1

Unbalanced Mode

1 ON OFF ON

2 ON OFF ON

3 OFF ON ON

4 OFF ON ON

Settings of SW2

Bit 120-ohm E1

Balanced Mode

75-ohm E1

Unbalance

d Mode

Description

1 OFF ON The RRING is for

connected to the

protection ground2 OFF ON

3 OFF ON

4 OFF ON


24/55


BBU Module --- WBBPa Board

Board number mandatory board, maximum is 6

Main Functions

Providing the CPRI interface for communication between the BBU and the

WRRU or WRFU

Processing uplink and downlink baseband signals and support HSUPA and

HSDPA function

Supporting 1+1 backup of the CPRI interface

According to the board chip processing capability, WBBP module include

seven specifications. Current WBBP is the A version, called WBBPa.

CPRI 0~2 (1.25G-2.5G): SFP LEDs


25/55


BBU Module --- WBBPa Board

LED of running status of board :


RUN Green ON The board has power input, yet the board is faulty.OFF The board has no power input or is faulty.

1s ON, 1s OFF The board is running properly.

0.125s ON/OFF Software is being loaded to the board.

ACT Green ON The board is running properly.OFF The board is not in use.

ALM Red OFF The board is running properly.ON The board has alarms on hardware and it should be replaced with a new one.

CPRI0

CPRI1

CPRI2Red

Green

OFF normal

ON The CPRI links over the optical cable are faulty.

Blinking at 2 Hz The RRU on the CPRI link is faulty in hardware.

Blinking at 0.5 Hz The RRU on the CPRI link is faulty in the antenna system connection.


26/55


BBU Module --- WBBP Board

There are 2 kinds of Baseband card, WBBPa and WBBPb.

The WBBPa support HSDPA (2 ms TTI) and support for HSUPA phase I (10 ms TTI).

The WBBPb support HSDPA (2 ms TTI), and support for HSUPA phase II (2 ms TTI).

Board

Type Cell

Uplink R99

/HSUPA CE

Downlink

R99 CE HSDPA Capacity

HSDPA

throughput

HSUPA

throughput

WBBPa 3 cells 128 256 45 HS-PDSCH codes 15Mbps 6Mbps

WBBPb1 3 cells 64 64 45 HS-PDSCH codes 15Mbps 6Mbps





27/55



STATE

Green

0.125s ON,0.125s OFF

The module is not registered, and noalarm is reported.


Red ON The module is reporting alarms.

BBU Module --- UBFA Board

Board number mandatory board, maximum is 1

Main Functions

Controlling the fan speed

Reporting the fan status to the WMPT

Detecting the temperature of the fan board


28/55


Panel of the UPEA Panel of the UPEB

BBU Module --- UPEU Board

Board number mandatory, maximum is 2, 1+1 backup

Main Functions

Converting -48 V or +24 V DC power input to +12 V DC power that is supported

by boards

Reporting alarms related to input and output under voltage

Providing transmission ports for RS485 signals and 8 dry contact alarm signals

-48V to +12V +24V to +12V


29/55


LED: The UPEU has one LED, indicating the running status of the board.


RUN Green ON The board is running properly.

OFF The board has no power input, or

the board is faulty.

Socket and Port: The UPEU has one socket and four ports.

Label Quantity Connector Type Function

PWR 1 3V3 DC power input

EXT-ALM1

1

RJ45

Transmitting dry contact alarm signals

EXT-ALM0 1 RJ45

MON1 1 RJ45 Transmitting RS485 environment

monitoring signalsMON0 1 RJ45

BBU Module --- UPEU Board


30/55


The UTRP provides ports for eight E1s/T1s and implements transport such as IP and

ATM between the BBU3900 and the RNC.


RUN Green ON The board has power input, yet the board is faulty.

OFF The board has no power input or is faulty.


0.125s ON, 0.125s OFF Software is being loaded to the board.

2s ON, 2s OFF The board is under test.

ACT Green ON The board is in active mode.

OFF The board is in standby mode.

ALM Red OFF The board is running properly.

ON The board is reporting alarms and is faulty.

BBU Module --- UTRP Board

4 E1:DB26


31/55


BBU Module --- UTRP Board Type

WCDMA UTRP extend transmission board

UTRP board should add sub board to provide the different interface type.

WD22UTRP is the main board name. The UTRP has three sub-boards in current version

UAEU: Eight ATM over E1s/T1s

UIEU: Eight IP over E1s/T1s

UUAS: One unchannelized ATM over SDH/SONET(STM-1/OC-3) interface

The board in gray table is not be delivered currently.TransmissionBoard name

Sub board

name

Interface type Interface specification

WD22UEEU WD22UEEC FE/GE electrical board 2*FE/GE (10/100/1000M

adaptive)

WD22UEOU WD22UEOC FE/GE optical board 2*FE/GE (10/100/1000M

configurated)

WD22UAEU WD22UAEC E1/T1 ATM interface sub board 8* E1/T1WD22UIEU WD22UPEC E1/T1 IP interface sub board 8*E1/T1

WD22UCPU WD22UCPS Channelization IP optical sub board 1*STM-1

WD22UUPU WD22UUPS Unchanneliazation IP optical sub board 1*STM-1

WD22UCAU WD22UCAS Channelization ATM optical sub board 1*STM-1

WD22UUAU WD22UUAS Unchanneliazation ATM optical sub board 1*STM-1


32/55


Label Connector Type

MON0 RJ45

MON1 RJ45

EXT-ALM0 RJ45

EXT-ALM1 RJ45

BBU Module --- UEIU Board

Port : The UEIU has four ports.

Board number: maximum is 1

The UEIU Functions

Connecting to an external monitoring device and transmitting RS485

signals to the WMPT

Connecting to an external alarm device and transmitting dry contact alarm

signals to the WMPT


33/55


BBU Module --- SLPU Board

The auxiliary devices of the

BBU3900. The devices are

the SLPU, UELP, and UFLP

SLPU:The signal lightning

protection unit is an optionalmodule of the BTS3900

cabinet (-48 V) or the power

distribution cabinet.

The UFLP and the UELPare optional units that are

installed in the SLPU.

UFLP

UELP


34/55


UELP: The universal E1/T1 lightning protection (UELP) unit is a universal E1/T1

The UELP can be optionally installed in the SLPU or the BBU. Each UELP

supports the surge protection of 4-way E1/T1 signals.

E1 Connection:

BBU Module --- UELP Board

DB25 DB26

Indoor DDF

E1

E1


35/55


DIP Switch: The UELP has one DIP switch, which is used to select whether the

receive terminal is grounded. The DIP switch has four bits.

DIP

Switch

DIP Status Description

1 2 3 4

S1 ON ON ON ON Used for the 75

unbalanced modeOFF OFF OFF OFF Used for other

modes except the 75

unbalanced mode

BBU Module --- UELP Board


36/55


UFLP: The universal FE lightning protection (UFLP) board is optionally installed in the

SLPU or BBU. Each UFLP supports 2-way FE surge protection.

BBU Module --- UFLP Board

IPCable Connection.

Transmission Equipment

LAN switch or Router


37/55









38/55


RF Module --- WRFU Board

The WRFU consists of the high-speed interface unit, signal processing unit,

power amplifier, and duplex unit


39/55



Type Label Connector Type DescriptionPort for

transceiving RF

signals

ANT-RXB DID connector Connecting the antenna

subsystem

ANT-TX/RXA DID connector

CPRI CPRI0 SFP female

connector

Connecting the BBU, or

the upper-level WRFU

during the cascading

CPRI1 SFP female

connector

Connecting the lower-

level WRFU during the

cascading

Interconnection port

for RF receive

signals

RX-INB QMA female

connector

Input port of diversity

signals in the antenna

channel

RX-OUTA QMA female

connector

Output port of diversity

signals in the antenna

channel

Power port PWR 3V3 power

connector

Introducing power

Commissioning port MON RJ45 connector Used for commissioning


40/55


Identifier Status Meaning

RUN On The power input is normal, but the module is faulty.

Off There is no power input, or the module is faulty.

On for 1 second and off for 1 second The module is functional.

On for 0.125 second and off for 0.125

second

The module is loading software or is not started.

ALM On The module is in the alarm status.

Off No alarm is generated.

ACT On The module is functional and is connected to the BBU.

Off The module is not connected to the BBU.

On for 1 second and off for 1 second The module is in the local test status.

VSWR Off (red) No VSWR alarm is generated.

On (red) A VSWR alarm is generated.

CPRI0

CPRI1

On (green) The CPRI link is normal.

On (red) The interface module fails to receive signals.

Red LED on for 1 second and off for

1 second

The CPRI link is out of lock.



41/55



RF specifications:

One WRFU supports four carriers

Each carriers maximum output power of WRFU is 80W

The receive sensitivity of single antenna is better than -125.8dBm

The receive sensitivity of two antennas is better than -128.6dBm

The maximum searching ability is 200km

The maximum access search radius is configurable with the step size of 300 m

Configuration Type (No

Transmit Diversity)

Transmit Diversity

Power (W)/Carrier

Typical Power

Consumption (W)

Maximum Power

Consumption (W)

3*1 20 520 630

3*2 20 610 830

3*3 20 810 1070

3*4 20 1020 1330


42/55









43/55


Power Distribution Modes of the BTS3900

- 48 V DC Distribution


44/55


- 48V Cabinet Power Module --- DCDU-01 Board

Function

The DCDU-01 supports one -48 V

DC power input and ten -48 V DC

power outputs

The DCDU-01 supplies power to

the BBU, WRFU, FAN, and user

devices inside cabinets

The DCDU-01 has the built-in

surge protector, which supports

the surge protection capability of

the differential mode of 10 kA and

the common mode of 15 kA

- 48V DC

Single Cabinet


45/55


- 48V Cabinet Power Module --- DCDU-01 Board

Name Label Description

Power input

wiring terminal

NEG(-) -48 V NEG input wiring terminal

RTN(+) -48 V RTN input wiring terminal

Power output port SPARE2, SPARE1,

BBU, FAN, and RFU5-

RFU0

RFU0 to RFU5 supplying power to six WRFUs

BBU supplying power to the BBU

FAN supplying power to the FAN

SPARE1 and SPARE2 reserved

Power switch SPARE2, SPARE1,

BBU, FAN, and RFU5-

RFU0

RFU0 to RFU5 controlling the ON/OFF of the current of

six WRFUs

BBU controlling the ON/OFF of the current of the BBU

FAN controlling the ON/OFF of the current of the FAN

SPARE1 and SPARE2 controlling the ON/OF of the

current on the SPARE1 and SPARE2 power output ports

Alarm output port SPD ALM DUDU-01 dry contact alarm output port


46/55


FAN Unit

The FAN unit refers to the fan box. The FAN unit provides the functions of ventilation

and heat dissipation for cabinets. One FAN unit has four independent fans.

Type Label Connector Type Description

Power port -48 V 3V3 power connector Introducing the -48 V

DC power

Temperature sensor port SENSOR RJ45 connector Connecting the

external temperature

sensor

Communication port COM OUT RJ45 connector Cascading the lower-

level FAN module

COM IN RJ45 connector Connecting the main

control unit


47/55









48/55


BBU3900 Cable Connection


49/55


Cables --- PGND Cable

PGND Cable

OT terminal

Name Color Cross-Sectional Area

PGND cable of the

BTS3900 WCDMA cabinet

Green and yellow The cross-sectional area of a wire is 25

mm2.

PGND cable of the DCDU Green and yellow The cross-sectional area of a wire is 6

mm2.

PGND cable for the SLPU Green and yellow The cross-sectional area of a wire is 6

mm2.

Front door PGND cable Green and yellow The cross-sectional area of a wire is 6

mm2.


50/55


Cables --- Power Cable

Power Cable Between the DCDU,BBU,FAN and WRFU


51/55


Cables --- Transmission Cable

E1 Cable

FE Surge Protection Transfer CableE1 Surge Protection Transfer Cable

FE Cable


52/55


Cables --- CPRI Cable

This describes the CPRI electrical cable. It helps to implement high speed

communication between the BBU3900 and the WRFU.

Appearance : The CPRI electrical cable is an SFP high speed transmission

cable that has a SFP200 male connector at each end.

One End The Other End

CPRI port on the WBBP CPR10 port on the WRFU


53/55






54/55


Configuration Types of the BTS3900

The BTS3900 supports omni-directional, 2-sector, 3-sector, and 6-sector

configurations. It also supports smooth capacity expansion from 1x1 to 3x8.

This part illustrates the configuration type of the BTS3900 by taking the WBBPa

supporting three cells and the WRFU supporting the 80W/4 carrier as an example.


55/55

www.huawei.com

Thank You