SPH-A940
CDMA TELEPHONE
CDMA TELEPHONE CONTENTS
1. General Introduction
2. Circuit Description
3. Installation
4. NAM Programming
5. Product Support Tools
6. Test Procedure
7. Flow Chart of Troubleshooting
8. Exploded Views and Parts List
9. Block Diagram
10. Electrical Parts List
11. PCB Diagrams
Samsung Electronics Co.,Ltd. November. 2005
Printed in Korea.
Code No.: GH68-08774A
BASIC.
ⓒ
This Service Manual is a property of Samsung Electronics Co.,Ltd.Any unauthorized use of Manual can be punished under applicableInternational and/or domestic law.
SAMSUNG Proprietary-Contents may change without notice
1. General Introduction
1-1
This Document can not be used without Samsung's authorization
1-1. General Instruction
The SPH-A940 enables mobile users to communicate 3G CDMA2000 1X service into a single handset.
For CDMA/PCS mode, The SPH-A940 supports Release A of the CDMA2000 1X standard.
The SPH-A940 is the first 2 mega pixel camera phone with 2x optical zoom and auto focus of Samsungfor North America that works on North American CDMA networks.
This stylish clamshell phone supports dual color displays, Bluetooth, MMS, voice dialing, airplane modeand EV-DO services.
SAMSUNG Proprietary-Contents may change without notice
General Introduction
1-2
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
2. Circuit Description
2-1
This Document can not be used without Samsung's authorization
2-1. Logic Section2-1-1. Power Supply
Press "END" key to turn on the phone and then the VBATT and ON_SW signals will be connected. This
turns on the inner regulators(V_MSMCORE, V_MSMC, VPD, VPA) of U203(MAX1526).
The VBATT applied to ON_SW will change ON_SW_SENSE signal from HIGH to LOW.
MSM6500(U101) sends out PS_HOLD(logical HIGH) to keep the inner regulators on even after the "END"
key is released. V_RFRX can be turned on/off by the RX_CTRL signal. V_TCXO can be turned on/off
by the TCXO_CTRL signal. The other regulators(2.85VDD, V_SYNTH, V_RFTX, V_MOTOR, V_LED) will
be in the ON/OFF state by I2C-compatible 2 wire serial interface.
The regulated Voltage(U203, V_MSMCORE) are used in the core of MSM.
The regulated Voltage(U203, V_MSMC) are used in the digital part of MSM.
The regulated Voltage(U203, VPD) are used in the digital part MSM.
The regulated Voltage(U203, VPA) is used in the analog part of MSM.
The regulated Voltage(U203, V_RFTX) is used in the Tx RF part.
The regulated Voltage(U203, V_RFRX) is used in the Rx RF part.
The regulated Voltage(U203, V_TCXO) is used in the TCXO.
The regulated Voltage(U203, V_SYNTH) is used in the PLL part.
The regulated Voltage(U203, 2.85VDD) is used in the Camera Display part and the T-Flash.
The regulated Voltage(U203, V_MOTOR) is used in the MOTOR.
The regulated Voltage(U203, V_LED) is used in the KEYPAD LED.
2-1-2. Inner Charging Circuit PartThe most important function of the charger shall be done in the PMIC(Power Management Circuit U203).
When the phone with a battery is connected with a travel charging adapter, the inner charging circuit of
the PMIC(U203) will charge the battery by constant fast charge mode.
When battery reaches regulation voltage of 4.2V (default charging voltage for Li+mode), the charge
current drops quickly to 0mA
- Input voltage range : 4.25∼6.5V
- Charging Temperature : 0°C∼40°C
- Charging Method : Constant Voltage/Current -Charging Current : Normal 550mA
- Charging Time : Standard (1100mAh) 2.5 ~ 3 Hrs , Extended (1700mAh) 3.5 ~ 4 Hrs
- Charging Mode : ① Charging ② Completion
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-2
This Document can not be used without Samsung's authorization
- Charging Battery Regulation Voltage
① Min 4.158V, Typical 4.2V, Max 4.242V(at TA : 0°C to +85°C)
② Min 4.137V, Typical 4.2V, Max 4.263V(at TA : -40°C to +85°C)
Universal Serial Bus Interface
SPH-A940 supports a Universal Serial Bus(USB) interface by the MSM6500, to provide an efficient
interconnection between the mobile phone and a Personal Computer(PC).
The MSM6500's USB interface is designed to comply with the Universal Serial Bus Specification,
Revision 2.0. An external USB transceiver(U203) is required to implement the USB interface.
2-1-3. Logic PartThe logic part consists of MSM, MEMORY, LCD, CAMERA, CCP, external MEMORY and other input and
output peripherals.
MOBILE SYSTEM MODEM(U101:MSM6500)
Industry standard ARM926EJ-S microprocessor is embedded. The MSM6500 chipset integrates
CDMA2000 1x and 1xEVDO service. The 1xEVDO solution can support High-speed peak data rates of
2.4Mbps on forward link and 153kbps on reverse link.
The MSM6500 device is offered in a 409 ball, 0.5mm pitch, CSP production package. Subsystems within
the MSM6500 device include a CDMA processor, a QDSP for voice compression, an ARM9TDMI
microprocessor. Also integrated in the MSM6500 device are analog functions such as an audio voice
codec, PLL, transmit DACS, ADCS, memories, USB controller, peripheral interfaces, and an enhanced
clock. It is one of the most important components of the CDMA cellular phone.
The interface circuitry consists of reset circuit, dual address/data bus and memory controls. The TCXO
clock of 19.2Mhz is used as the main clock of SPH-A940 model.
MCP : NAND FLASH and SDRAM (U102(KBE00F003M))
MCP is consist of two 512Mbit(64M*8) NAND FLASH and two 256Mbit(4M*16*4Banks) Mobile SDRAM.
NAND FLASH is used to store the Font data and program. EFS area is used to store ESN, NAM
information, telephone directory, SMS messages and other important information of the phone, and also
to store application programs and downloaded stuffs such as BREW applications and MP3. MCP is also
used to excute the DMSS(Dual Mode Subscriber system) software.
Using the down-loading program, the program can be changed even after the terminal is fully assembled.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-3
This Document can not be used without Samsung's authorization
Keypad
For key recognition, key matrix is operated by using SCAN(0:7) and KEYSENCE(0:3) of the input ports
of MSM. 23 backlight LEDs and back-light circuitry are included in the keypad for easy operation in the
dark.
LCD Module
LCD is composed of a Transmissive with Micro Reflective(TMR) type Main TFT-LCD Panel, Transflective
type Sub TFT-LCD Panel, a driver circuit and a back-light unit.
The resolution of a 2.0" Main LCD(TMR) contains 176 * 220 pixels, the resolution of a 1.17" Sub
LCD(Transflective) contains 96 * 96 pixels.
Clock
CPU clock : 19.2MHz. Clock signal from the TCXO
Sleep clock : 32.768KHz. Clock signal for sleep.
TCXO/N : 19.2/N MHz. This clock source is used by various blocks of the MSM6500 device, such
as the ARM9CORE, UARTs, general-purpose PDMs and TCXO is also used by the
MSM6500 device to produce CHIPX8.
USB clock : 48MHz. Clock signal for the USB interface
CAMERA
The camera module consists of 1/3 type 2 Mega (2140K) Pixels CCD sensor, Digital signal processor,
and MPU. The camera module provides Auto Focus, 2x Optical Zoom, Auto Exposure, and Auto White-
Balance functionality.
CCP (Camera Control Processor)
CCP can support sensors up to 2M pixels. CCP directly transmits and previews the RGB data to the
LCD graphic memory by processing the sensor output data according to the MSM's command and
provides hardware based real-time JPEG compression and decompression. CCP can save the raw RGB
data up to SVGA resolution into its image buffer and allows the host processor to download with
scalable sized compressed data. In addition, CCP can download the compressed image to either store
the original RGB data or transfer the image to the LCD.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-4
This Document can not be used without Samsung's authorization
Bluetooth module
Bluetooth module is a BluetoothTM 1.1 and 1.2 compliant, stand-alone baseband processor with an
integrated 2.4GHz transceiver. Bluetooth module supports any voice and/or data application that requires
the Bluetooth SIG standard Host Controller Interface (HCI) via UART and PCM audio interfaces.
Operation Clock: 19.2MHz
Low-Power Clock: 32.768KHz
2-1-4. RF Interface Part
CDMA Data Interface
- TX_Q_P, TX_Q_N, TX_I_P, TX_I_N (U400) : Tx analog signal used during CDMA
- RX_I_P, RX_Q_P, RX_I_N, RX_Q_N (U302) : RX analog signal used during CDMA
RF Interface
- TX : TX_AGC_ADJ(U101) is used to control the TX power,
PA_ON_PCS(U101) is used to control the PCS power amplifier and
PA_ON_CELL(U101) is used to control the CDMA power amplifier.
- RX : TRK_LO_ADJ(U101) is used to compensate the TCXO module.
2-1-5. Audio PartThe MSM6500 device integrates a stereo wideband voice/audio CODEC into the Mobile Station Modem.
The integrated CODEC contains all of the required conversion and amplification stages for the
audio front end.
The CODEC operates as a 13bit linear CODEC with the transmit(TX) and receive(RX) filters designed
to meet ITU-T G.712 requirements. The CODEC contains the software controlled amplifier for both the
receiving and transmitting sections. Also, the vocoding schemes used will be 13kbps QCELP and 8Kbps
EVRC. The QCELP vocoder is based in the MSM internally.
2-1-6. Tx Audio PathThe voice signal from the microphone is filtered and amplified by the internal OP-AMP and is converted
to PCM data by the internal CODEC in the MSM. And then these signals are applied to the the
MSM(U101)'s internal vocoder.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-5
This Document can not be used without Samsung's authorization
2-1-7. Rx Audio PathThe PCM data from the MSM(U101) is inputted to the internal CODEC and the data will be decoded by
the internal DAC. Audio levels are adjusted by the amplifier. And then audio is sent to the receiver.
2-1-8. Speaker PathWhen the MSM(U101) receives the data, its internal CMX generates bell and melody. The CMX bell and
melody generated in MSM6500 are sent to SAPA1D2.
The SAPA1D2 (stereo class - D audio power amplifier) is a high quality audio power conversion chip
generating 2.5W RMS output directly from the VBATT supply. It is a high efficiency audio amplifier for
mobile applications. The gain of amplifier in SPH-A940 set to 4(V/V) . The output generated in SAPA1D2
is intended to drive two speakers.
2-1-9. Key Tone GeneratorThe CODEC data out from the MSM6500 is converted to DTMF signal by TONE generator of internal
CODEC, which is then amplified by the internal audio amplifier to be sent to the receiver unit.
2-2. PCS Section
2-2-1. Receiver
LOW NOISE AMPLIFIER (U301)
The low noise amplifier(It is included in FC7510 : U301) amplifies a weak signal received from the base
station to obtain the optimum signal level.
RF BAND PASS FILTER (F302)
The RF BPF(F302) passes only a specific frequency(1960±30 MHz) from the signal received from the
mobile station. The bandwidth is 60 MHz.
VOLTAGE CONTROLLED OSCILLATOR(OSC301)
The VCO(OSC301) generates the signal having 1715 ~ 1788MHz frequency range.
The VCO's output frequency is changed by control voltage. The PLL in S1M8690X generates this control
signal and this signal is changed into DC control voltage by R-C Loop filter.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-6
This Document can not be used without Samsung's authorization
Frequency Synthesizer Circuit
The PLL(Phased Locked Loop) block consists of VC-TCXO(OSC302), PLL in S1M8690X and
VCO(OSC301). Input reference frequency is generated at VC-TCXO(OSC302) and the RF local signal is
generated at VCO. PLL compares the two signals and generates the desired signal with a
preprogrammed counter which controls voltage.
VOLTAGE CONTROLLED TEMPERATURE COMPENSATED CRYSTAL OSCILLATOR (OSC302)
The VC-TCXO (OSC302) is a reference source of the frequency synthesizer. It provides 19.2MHz
reference frequency to PLL-IC. It is a voltage controlled temperature compensated crystal
oscillator having 19.2MHz ±2.5ppm frequency stability over all useful temperature range.
A correct frequency tuning is made by the control voltage.
2-2-2. Transmitter
Intenna
Intenna sends signal to the base station and receives the signal from the base station.
It is a tri-band Intenna and covers PCS band, CDMA band and GPS band.
RF Switch
It(U405) is used to switch the PCS path, the CDMA path and the GPS path, The RF signal passes
through PCS & CDMA path when GPS_MODE is low.
GPS_MODE is a digital signal from MSM6500 GPIO.
Duplexer
Duplexer(F402) allows to transmit only the signals within acceptable Tx frequency range
(1880 ± 30 MHz) through the Intenna.
It provides the appropriate attenuation of transmitted signal at the receiver input and the appropriate
rejection of the transmit-generated noise in the Receiver band.
Power Amp
Power amplifier module(U404:ACPM-7833-DC1) amplifiers signal to be sent to the base station
through the antenna.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-7
This Document can not be used without Samsung's authorization
Driver Amp
The driver amp(U400 ; included in S1M8690X) allows the signal to be inputted to the power amp(U404)
as a specified level.
Up-converter(Mixer)
The up-converter(U402 ; also included in S1M8690X) receives the local signal FTx * 0.7999
and signal controlled by TX AGC amp(in S1M8690X) to generate Tx RF signal 1880±30MHz
which signal comes out from the mixer output by adding FTx * 0.7999 local signal.
FTx means TX RF signal Frequency.
Automatic Gain Control Amp
The TX IF AGC amp (in S1M8690X) controls gain of AGC to deliver power level needed at
driver amp. Its control voltage varies from 0.2V to 2.5V.
2-3. CDMA Section
2-3-1. Receiver
Low Noise Amplifier(LNA)
The low noise amplifier(It is included FC7510 : U301) amplifies a weak signal received from
the base station to obtain the optimum signal level.
RF Band Pass Filter(Rx RF SAW Filter)
The RF BPF in F301 passes only a specific frequency(881.49±12.5 MHz) from the signal
received from the mobile station. The bandwidth is 25 MHz.
Voltage Controlled Oscillator
The VCO(OSC301) generates the signal having 1715 ~ 1788MHz frequency range.
The VCO's output frequency is changed by control voltage. The PLL in S1M8690X generates this control
signal and this signal is changed into DC control voltage by R-C Loop filter.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-8
This Document can not be used without Samsung's authorization
Frequency Synthesizer Circuit
The PLL(Phased Locked Loop) block consists of VC-TCXO(OSC302), PLL in S1M8690X and
VCO(OSC301). Input reference frequency is generated at VC-TCXO(OSC302) and the RF
local signal is generated at VCO. PLL compares the two signals and generates the desired
signal with a preprogrammed counter which controls voltage.
VC-TCXO
The VC-TCXO (OSC302) is a reference source of the frequency synthesizer. It provides 19.2MHz
reference frequency to PLL-IC. It is a voltage controlled temperature compensated crystal
oscillator having 19.2MHz ±2.5ppm frequency stability over all useful temperature range.
A correct frequency tuning is made by the control voltage.
2-3-2. Transmitter
Intenna
Intenna sends signal to the base station and receives the signal from the base station.
It is a tri-band Intenna and covers PCS band, CDMA band and GPS band.
RF Switch
It(U405) is used to switch the PCS path, the CDMA path and the GPS path, The RF signal
passes through PCS & CDMA path when GPS_MODE is low.
GPS_MODE is a digital signal from MSM6500 GPIO.
Duplexer
Duplexer(F405) passes the RF signal of Rx frequency range(881.49 ±12.5 MHz) and Tx frequency range
(836.49 ±12.5 MHz). It provides appropriate attenuation of transmitted signal at the receiver input and
appropriate rejection of the transmit-generated noise in the Receiver band.
It also matches LNA input in receiving part and PAM(U403:ACPM-7813) output in transmitting part with
the Intenna.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-9
This Document can not be used without Samsung's authorization
Power Amp
Power amplifier module(U403:ACPM-7813-DC1) amplifiers signal to be sent to the base station
through the antenna.
RF Band Pass Filter(Tx RF SAW Filter)
The RF BPF(F404) passes only specific frequency(836.49 ±12.5MHz) to send it to power
amp(U403:ACPM-7813-DC1).
Driver Amp
The driver amp(U402 ; It is included in S1M8690X) allows the signal to be inputted to the
power amp(U403) as a specified level.
Up-Converter(Mixer)
The up-converter(U402 ; It is also included in S1M8690X) receives the local signal FTx * 1.6666
and the signal controlled by TX AGC amp(in S1M8690X) to generate Tx RF signal
836.49±12.5MHz signal comes out from the mixer output by adding FTx * 1.6666 local signal.
FTx means TX RF signal Frequency.
Automatic Gain Control Amp
The TX IF AGC amp in S1M8690X controls gain of AGC to deliver power level to be needed
at Driver amp. Its control voltage varies from 0.2V to 2.5V.
SAMSUNG Proprietary-Contents may change without notice
Circuit Description
2-10
This Document can not be used without Samsung's authorization
2-4. GPS Section
Intenna
Intenna receives a signal from GPS satellites.
It is a tri-band Intenna and covers PCS band, CDMA band and GPS band.
RF Switch
It(U405:TQP4M3018) is used to switch the PCS path and CDMA path and the GPS
path. The RF signal passes through PCS path when PCS_MODE is high(2.6V). The RF signal
passes through CDMA path when CELL_MODE is high(2.6V). The RF signal passes through
GPS path when GPS_MODE is high(2.6V). PCS_MODE, CELL_MODE and GPS_MODE are
digital signals from MSM6500 GPIO.
Low Noise Amplifier(LNA)
The low noise amplifier(Q302:ATF55143) amplifies a weak signal received from the base station to
obtain the optimum signal level.
RF Band Pass Filter(Rx RF SAW Filter)
The RF BPF(F303:DG75BS1) passes only a specific frequency(1575.42±1MHz) from the signal received
from the satellite. The bandwidth is 2 MHz.
SAMSUNG Proprietary-Contents may change without notice
3. Installation
3-1
This Document can not be used without Samsung's authorization
3-1 Installing and Removing the Battery
To install, insert the battery into the opening onthe back of the phone making sure the plastic tabson the back are inserted into the matching slots inthe phone. Press down until the latchsnaps intoplace.
To remove, make sure the power is off. Push thebattery release latch up completely. Pull and lift thebattery away from the phone.
3-2 Using the Desktop Charger
1. Plug the AC cord from the charger into theelectrical outlet.
2. Insert the phone into the slot.
◇ A red light on the charger lets you know thebattery is charging.
◇ A green light lets you know that the battery isat least 90 percent charged.
◇ A orange light indicates that the battery isoperating at a temperature that is too high orlow, or that the charger is not plugged incorrectly. Please check the charger and thebattery.
Specifications using DTC (Desktop Charger)
Battery TypeStandard Battery(Li-ion, 1000mAh)
Extended Battery(Li-ion, 1700mAh)
Charging < 5 hours < 5 hoursSEC Code GH43-02160A GH43-02161A
SAMSUNG Proprietary-Contents may change without notice
Installation
This Document can not be used without Samsung's authorization
3-2
SAMSUNG Proprietary-Contents may change without notice
4. NAM Programming
4-1
This Document can not be used without Samsung's authorization
NAM features can be programmed as follows:
Notes:For example, press 'menu' and cursor to 'settings & tools' and '*' , then press ' 000000' (000000:SPC code), you can see'Service' Mode.
NAM SETTING FLOW:
LCD Display Key in Function
Service Mode
1. ESN***********(Decimal number)********(Hexa Number)
Enter (↓) -Electronic Serial Number of the phone isdisplayed
2. AKEYAKEY
numberEnter
AKEY Setup.- To input AKEY, enter AKEY #.- Stores it
3. Network Setting-1 Phone Number
Phone Number(MDN)0000006034
Enter (OK), andthen enter thenumber
The phone number screen enables you toedit the phone number
3. Network Setting-2 MCC
MCC310
Enter the numberThe MCC screen allows you to view and
modify the mobile country code.
3. Network Setting-3 NMSID
NMSID(NATIONALMOBILE STATION ID)
000000006034
Enter the number
3. Network Setting-4 True IMSI MCC
True IMSI MCC000
Enter the numberIMSI_S screen allows you to view and
modify the international mobile stationidentity
3. Network Setting-5 True IMSI NMSID
True IMSI NMSID000000006034
Enter the number
SAMSUNG Proprietary-Contents may change without notice
NAM Programming
4-2
This Document can not be used without Samsung's authorization
3. Network Setting-6 PRL Enabled
PRL EnabledYesNo
The PRL screen shows if the preferredroaming list (PRL) is enabled.
3. Network Setting-7 Home SID/NID
Enter SID2004Enter NID65535
Enter the number
This screen allows you to view and modifythe various home system ID (SID) andnetwork ID(NID) settings.
3. Network Setting-8 CDMA Pri Chn A
CDMA Pri Chn A283
Enter the numberThe primary channel A screen allows you toview and modify primary channel A.
3. Network Setting-9 CDMA Sec Chn A
CDMA Sec Chn A691
Enter the numberThe secondary channel A screen allows youto view and modify secondary channel A.
3. Network Setting10 CDMA Pri Chn B
CDMA Pri Chn B384
Enter the numberThe primary channel B screen allows you toview and modify primary channel B
3. Network Setting-11 CDMA Sec ChnB
CDMA Sec Chn B777
Enter the numberThe secondary channel B screen allows youto view and modify secondary channel B.
3. Network Setting12 Home Sys Reg
Home Sys RegYesNo
Home SID Reg – home system ID
3. Network Setting-13 Forgn SID Reg
Forgn SID RegYesNo
Foreign SID Reg – foreign system ID
SAMSUNG Proprietary-Contents may change without notice
NAM Programming
4-3
This Document can not be used without Samsung's authorization
3. Network Setting-14 Forgn NID Reg
Forgn NID RegYesNo
Foreign NID Reg – foreign network ID
3. Network Setting-15 Access OverloadClass
Access Overload Class4
Enter the numberThe overload class screen allows you to viewand modify the overload class.
3. Network Setting-16 Origination Voice
Orgination Voice SOEVRC13k
4. SMS SettngsSMS UTC timeYesNo
Selecting the SMS settings option allows youto view and edit the short message services(SMS).
5. Slot Cycle IndexSlot Cycle Index1
Enter the numberThis option allows you to view and modifythe slot cycle index. To modify the index,select Edit
6. Service ProgrammingCode
Service ProgrammingCode
000000
Enter the number
SAMSUNG Proprietary-Contents may change without notice
NAM Programming
4-4
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
5. Product Support Tools
5-1
This Document can not be used without Samsung's authorization
5-1. General
IMPORTANT INFORMATIONPurpose
The Product Support Tool (PST) offers you the ability to interface with the SAMSUNG mobile phoneusing a PC. With this tool you can program the phones network system requirements and functionality,data, and download software upgrades. This document supports SamsungPST(Samsung Product SupportTool).
EQUIPMENT REQUIREDMake sure you have the following equipment setup:1. Minimum PC configuration: 586 CPU, 64MB RAM, Windows2000/XP and abolve, 5MB of disk space
free for software upgrade.2. PST Software with appropriate cable (USB Cable for SAMSUNG mobile phone).3. USB Port.4. Power Supply (3.8 V) or Battery.
INSTALLATION1. Insert the SPH-A940 CDROM into your CD-Rom drive.2. Run the file explorer and run the Setup.exe file.3. After SamsungPST is installed on a computer, connect the phone, cable, and PC .
SAMSUNG Proprietary-Contents may change without notice
Product Support Tools
5-2
This Document can not be used without Samsung's authorization
5-2. PST (Product Support Tool)
5-2-1 Getting StartedMAIN MENU SCREEN1. Double Click on your "Samsung PST for Verizon (SE)"2. Select SPH-A940The Main Menu Screen shows the basic tasks that are available.CAUTION: DO NOT attempt to program phone with a low battery.
5-2-2 Operation ProcedureInformationClick "Read general Information" icon.
Software DownloadIf the phone works normally, you must proceed below procedures.Normal Download.1. Connect PC and SPH-A940 with usb cable2. Check com port of SAMSUNG CDMA Modem. To check on Com port, first you go to my
computer->property->Hardware->Device Manager ->Modem->Samsung USB Modem. Then go to propertyof Samsung USB Modem, and then click on Modem tab. You may see the port number, which isassigned for Samsung USB Modem.
3. Run Samsung PST.4. Change PST's comport setting ( Setup COM Setting ) same as com port of 'SAMSUNG cdma
modem'5. Select SPH-A940 and then click SW(Software Download) tab.6. Select 'Normal' in software download option.7. Click 'openfile' icon and select the bin file.8. Click 'Start Software Download' icon.10. When the downloading process is finished, the A970 power on automatically and the PST shows"Downloading completed!!".
If the phone doesn't works normally, you must proceed below procedures.Emergency Download.1. SPH-A940 enters the emergency mode(press simultaneously '9' and 'PWR')2. Connect PC and SPH-A940 with usb cable3. Check com port of SAMSUNG CDMA Modem. To check on Com port, first you go to my
computer->property->Hardware->Device Manager ->Modem->Samsung USB Modem. Then go to propertyof Samsung USB Modem, and then click on Modem tab. You may see the port number, which isassigned for Samsung USB Modem.
SAMSUNG Proprietary-Contents may change without notice
Product Support Tools
5-3
This Document can not be used without Samsung's authorization
4. Run Samsung PST.5. Change PST's comport setting ( Setup COM Setting ) same as com port of 'SAMSUNG cdma
modem'6. Select SPH-A940 and then click SW(Software Download) tab.7. Select 'Emergency" in software download option.8. Click 'openfile' icon and select the bin file.9. Click 'Start Software Download' icon.10. When the downloading process is finished, the A970 power on automatically and the PST shows"Downloading completed!!".
PRL Download1.Click "Open PRL1 file" icon and select the PRL file.2.Click "Start PRL Download" icon.3. When the downloading process is finished, the A970 will reboot automatically and the PST shows"Completed PRL Programming"
ERI Download1.Click "Open ERI1 file" icon and select the PRL file.2.Click "Start ERI Download" icon.3. When the downloading process is finished, the A970 will reboot automatically and the PST shows"Completed ERI Programming"
SettingRead Data from FileClick "Open mmc" icon to select the name of a file whose extension is "mmc". The values will be readfrom the named file, and will initialize the parameter values seen on the Settings screen
Read Data from PhoneClick Read from the Phone icon to upload the current programmable parameters of the phone. Thevalues are read from the phone, so the phone must have the power ON and be properly connectedto the PST.NOTE: To actually view the data you need to go to the Edit Items screens.
Edit ItemsClick this icon to edit Number Assignment Module (NAM) items or UI items.1. GeneralNAM : Slot Cycle Index, Service Code2. NAM1
SAMSUNG Proprietary-Contents may change without notice
Product Support Tools
5-4
This Document can not be used without Samsung's authorization
Save Data to FileClick this icon to save the current parameters to a file. Once you enter a filename, Click button towrite all current parameters to that file. This way the same information can be downloaded into multiplephones.
Write to PhoneClick this icon to write the selected parameter values to the phone. Writing the selected values to thephone may take up to a minute. If there are dependencies in a field you can make all the changes inthe proper fields and download the information all together.If you intend to use this write to Phone? feature, it is recommended that you do a "Read Data fromPhone" first, and then make the changes, so that nothing gets inadvertently overwritten.NOTE: DO NOT TOUCH THE PHONE WHILE WRITING IS IN PROGRESS.
TransferBackup Items1. Select Item to backup in 'Item option' list.2. Select 'backup' in 'Backup or Restore' list.3. Click "Start Backup of Restore" icon.
SAMSUNG Proprietary-Contents may change without notice
6. Test Procedure
6-1
This Document can not be used without Samsung's authorization
6-1 List of Equipment● DC Power Supply
● Test Jig
● Test Cable
● CDMA Mobile Station Test Set HP8285A, HP8960, CMD-80, etc
● Spectrum Analyzer(include CDMA Test Mode) HP8596E,
6-2 Configuration of Test
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-2
This Document can not be used without Samsung's authorization
6-3 TEST CABLE CONNECTIONS
6-3-1 TEST CABLE
6-3-2 TEST CABLE CONNECTIONS
1 MHC 172
2 RF CABLE (1.4dB Loss for CDMA, 2.1dB Loss for PCS, 1.8dB Loss for GPS)
3 BNC CONNECTOR (RF)
4 DATA CABLE
5 Plug Connect to SPH-A940
6 Dsub 25PIN CONNECTOR (DATA)
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-3
This Document can not be used without Samsung's authorization
6-3-3 Dsub 25 PIN CONNECTOR PIN DESCRIPTION (TEST CABLE 1, BACK SIDE)
DATA DESCRIPTIONDsub CONN.PIN NO.
DATA DESCRIPTIONDsub CONN.PIN NO.
GND 13 GND 24,25 (SHORT)
VBATT 4 VBATT 5,6 (SHORT)
HP_PWR 7 DP_RX_DATA 21
RX_AUDIO 12 DP_TX_DATA 22
TX_AUDIO 10
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-4
This Document can not be used without Samsung's authorization
6-3-4 CONVERSION TABLE OF FREQUENCY vs CHANNEL
- CDMA/PCS
T Y P E CHANNEL CONVERSION EQUATION REMARK
TXFREQUENCY
990 ≤N≤10231 ≤N≤779
F=0.03 × (N-1023) + 825.00F=0.03 × N + 825.00
N ; CH NUMBER
F ; FREQUENCY
(CDMA)RX
FREQUENCY990 ≤N≤1023
1 ≤N≤779F=0.03 × (N-1023) + 875.00F=0.03 × N + 875.00
TXFREQUENCY 0 ≤N≤ 1199 F=0.05 × N + 1850.00
N ; CH NUMBER
F ; FREQUENCY
(PCS)RX
FREQUENCY 0 ≤N≤ 1199 F=0.05 × N + 1930.00
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-5
This Document can not be used without Samsung's authorization
6-4 Test Procedure
6-4-1 CDMA/PCS mode
- Change the test modeA. To change the phone's state from Normal Mode to Test Mode, You should enter the following keys.
: Press [ 4 7 * 6 8 # 1 3 5 8 0 ]
B. The command "0 0 1" is Suspend.
C. The command "0 2 2" is mode and channel change.
"2 0 3 6 3"
Channel number
Mode:CDMA
"3 0 6 0 0"
Channel number
Mode:PCS
and press enter key from the soft key board to save mode/channel value..
D. The command "0 0 1" is Suspend.
E. To finish the Test Mode, You should enter the command "0 0 2".
6-4-2 Channel selection and Tx power output level control
CDMAA. Enter to Test Mode [ 4 7 * 6 8 # 1 3 5 8 0 ]
B. "0 0 1" : Suspend.
C. The command "0 2 2" is mode and channel change
"2 0 3 6 3"
Channel number
Mode:CDMA
Push the [OK] key to save.
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-6
This Document can not be used without Samsung's authorization
D. To finish the Test Mode, You should enter the command "0 0 2".
E. Enter to Test Mode [ 4 7 * 6 8 # 1 3 5 8 0 ]
F. "0 0 1" : Suspend.
G. "0 1 1" : Carrier_On.
H. "0 1 4" : CDATA.
I. "0 9 2" : PA_RANGE_1.
J. "0 1 9" : Adjust RF power level.
PCSA. Enter to Test Mode [ 4 7 * 6 8 # 1 3 5 8 0 ]
B. "0 0 1" : Suspend.
C. The command "022" is mode and channel change
"3 0 6 0 0"
Channel number
Mode:PCS
Push the [enter] key to save.
D. To finish the Test Mode, You should enter the command "0 0 2".
E. Enter to Test Mode [ 4 7 * 6 8 # 1 3 5 8 0 ]
F. "0 0 1" : Suspend.
G. "0 1 1" : Carrier_On.
H. "0 1 4" : CDATA.
I. "0 9 2" : PA_RANGE_1.
J. "0 1 9" : Adjust RF power level.
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-7
This Document can not be used without Samsung's authorization
- CDMA Test items
TEST ITEMS PROCEDURE
1. PREPARANCE Set test equipments up.
[ 4 7 * 6 8 # 1 3 5 8 0 ] : Enter the Test Mode"0 0 1" : SuspendConfirm that the phone is in the "CDMA Mode".(If not CDMA Mode, Use Test Command "022""2XXXX" and Pushthe " " Key to "OK", and enter "0 0 2" to restart)
If you select a wrong key, press " # ", then enter new command.To exit the Test Mode at any time, just press [0 0 2].
2. FREQUENCYACCURACY
"0 0 1" : Suspend."0 1 3 0 3 6 3 * " : Set channel to 363."0 1 1" : Carrier On."0 1 4" : Spread spectrum."0 1 9 X X X ' END[Push and Hold] ' " : Set AGC Code(XXX) level.Measure the TX frequency : 835.89MHz±300Hz.
3. OCCUPIED CDMABANDWIDTH
"0 0 1" : Suspend."0 1 3 0 3 6 3 * " : Set channel to 363."0 1 1" : Carrier On."0 1 4" : Spread spectrum."0 1 9 X X X ' END[Push and Hold] ' " : Enter AGC Code(XXX) to adjust
RF Output Power.Measure the bandwidth (spec: 1.23MHz).
4. LIMITATIONS ONEMISSIONS
"0 0 1" : Suspend."0 1 3 0 3 6 3 * " : Set channel to 363."0 1 1" : Carrier On."0 1 4" : Spread spectrum."0 9 2" : PA_RANGE_1."0 1 9 X X X ' END[Push and Hold] ' " : Enter AGC Code(XXX) to adjust
RF Output Power.Measure the spurious at FC±900kHz, FC±1.98MHz, 2FC, 3FC, 1/2FC.
spec: FC±900kHz below 42dBc/30kHzFC±1.98MHz below 54dBc/30kHzOutside Receive Band 43+10log (PY)PY: Mean Output Power in watts
5. GATED POWER &TIME
Set the service option 2.Set the data rate Eighth (1200bps).Registering: HHP → HP8924C.Call : HP8924C → HHP.Measure the Gated Power & Time.
spec : Gated Power - at least 20dBGated Time - Rising Time : below 6㎲
Falling Time : below 6㎲Burst Time : below 1.25㎳
SAMSUNG Proprietary-Contents may change without notice
Test Procedure
6-8
This Document can not be used without Samsung's authorization
- PCS Test items
TEST ITEMS PROCEDURE
1. PREPARANCE Set test equipments up.
[ 4 7 * 6 8 # 1 3 5 8 0 ] : Enter the Test Mode"0 0 1" : SuspendConfirm that the phone is in the "PCS Mode".(If not PCS Mode, Use Test Command "022""3XXXX" and Pushthe [OK] Key, and enter "0 0 2" to restart)
If you select a wrong key, press " # ", then enter new command.To exit the Test Mode at any time, just press [0 0 2].
2. FREQUENCYACCURACY
"0 0 1" : Suspend."0 1 3 0 6 0 0 * " : Set channel to 600."0 1 1" : Carrier On."0 1 4" : Spread spectrum."0 1 9 X X X ' END[Push and Hold] ' " : Set AGC Code(XXX) level.Measure the TX frequency : 1880.00MHz±300Hz.
3. OCCUPIED CDMABANDWIDTH
"0 0 1" : Suspend."0 1 3 0 6 0 0 * " : Set channel to 600."0 1 1" : Carrier On."0 1 4" : Spread spectrum."0 1 9 X X X ' END[Push and Hold] ' " : Enter AGC Code(XXX) to adjust
RF Output Power.Measure the bandwidth (spec: 1.23MHz).
4. LIMITATIONS ONEMISSIONS
"0 0 1" : Suspend."0 1 3 0 6 0 0 * " : Set channel to 600."0 1 1" : Carrier On."0 1 4" : Spread spectrum."0 9 2" : PA_RANGE_1."0 1 9 X X X ' END[Push and Hold] ' " : Enter AGC Code(XXX) to adjust
RF Output Power.Measure the spurious at FC±1.25MHz
spec: FC±1.25MHz below 42dBc/30kHz
5. GATED POWER &TIME
Set the service option 2.Set the data rate Eighth (1200bps).Registering: HHP → HP8924C.Call : HP8924C → HHP.Measure the Gated Power & Time.
spec : Gated Power - at least 20dBGated Time - Rising Time : below 6㎲
Falling Time : below 6㎲Burst Time : below 1.247㎳
SAMSUNG Proprietary-Contents may change without notice
7. Flow Chart of TroubleShooting
7-1
This Document can not be used without Samsung's authorization
7-1 Logic Section
7-1-1 Power On
Insert Power
power onproperly?
U203pin41=high?
C219 =2.7V?
C17219.2MHz?
END
Check Phone power on section
Check CON203 and it'sneighboring circuits
CheckC220,C222,C223,C224,C225,C226
and U203's neighboring circuits
Check OSC302,U107 and it'sneighboring circuits
YES
YES
YES
YES
NO
NO
NO
NO
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-2
This Document can not be used without Samsung's authorization
(1.375V)
(1.8V)
(2.6V)
(2.85V)
(2.7V)
(2.7V)
(2.85V)(3.1V)(3.3V)
(2.85V)
(2.85V)
C22
4C217R212
L201
C240
R206D201
C276
L202
R208
C202
C213
R211
C22
3
VPD
C215
C22
0
S3.6
C22
6
VBATT
R209
C277
R215
R210
DYIN34 DYOUT
2 GND 5VBUS
U2041 DXIN 6DXOUT
C22
7
C229
C21
9
C231
C203
C230 C232
C208
C212
C216
19
VTR
MV
US
B
18
38 _AC_OK
_HRESET42
_OE16
_ONO2
48_RESET
RCV
45REFBP
RX_EN 43
SUSPEND17
TCXO_EN 39
VICHG37
VL36
22 VMVP21
OUT6OUT7 3
5OUT8OUT9 6
PGND1 32
PGND2 28
PWR_HOLD41
46 PWR_ON
20
50NCNC 51
OUT1 10
OUT2 8
OUT3 13
7OUT4
1OUT5
47
26 HP_PWR
30
IN1
IN2
94
IN3
INV111
INV215
31LX1
LX2 29
COMP1
COMP214
24
D+D-
23
DATA25
FB1 33
FB2 27
44
GN
D
GND 49
U203
BA
TT
34
CH
G_I
N
35
40 CLK
12
D202
C201
C207
C214
C218
C22
8
R213C
225
VPD
C22
2
V_MOTOR
V_MSMCORE
V_MSMC
TCXO_CTRL
EAR_DET
VPA
V_RFTX
SEND_END
SCL_PM
DC_VOLT
V_LED
V_SYNTH
2.85VDD
USB_VPOUSB_VMO
USB_SUSPEND
RX_CTRL
USB_DATA
ON_SW
PS_HOLD
V_TCXO
V_RFRX
VPD
EAR_MIC
EAR_REF
SDA_PM
VICHG
HRESET
HP_PWR
V_BUS
RESETIN_N
ON_SW_SENSE
USB_OE_N
DC_SENS
VPULL
VPULL
D-
D+
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-3
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-4
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-5
This Document can not be used without Samsung's authorization
7-1-2 LCD Working
Insert Power
Main LCD Back-light On?
LCD DisplayOK?
Check pulseof V503's pin6
Check HEA501,F500, F501
F502,F503,andit's Short=?
Yes
Yes
NoNo
YesNo
No
Yes
Check HEA501 and it'sneighboring circuits
Replace HEA501,F500, F501 F502,F503 and
it's neighboring circuits
Change LCD
Change LCD
END
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-6
This Document can not be used without Samsung's authorization
(2.7V)
C512
C516
5O
UT4
OU
T36
OU
T27
OU
T18
F5039 GN
DG
ND
10
1IN
1
IN2
23IN
3
IN4
4
34IN
4O
UT4
5 6O
UT3
7O
UT2
8O
UT1
F501
GN
D
910 G
ND
1IN
1
2IN
2
IN3
U516
C513
C500
1234
56
78
* V504
VP
D
456
78
V500
*
123
C514
* V503
1234
56
78
C511
IN4
45
OU
T4
OU
T36
OU
T27
OU
T18
F500
9 GND
GN
D
10
1IN
1
IN2
23IN
3
G49
55
5050
66
778
89
9
G5152
4141
4242
4343
4444
4545
4646
4747
4848
49
3434
3535
3636
3737
3838
3939
44
4040
2727
2828
2929 3
3
3030
3131
3232
3333
2220
2021
2122
22
2323
2424
2525
2626
1213
1314
14
1515
1616
1717
1818
1919
HE
A501
11
1010
1111
12
S3.6
5678
*V
501
12
34
IN2
IN3
34IN
4O
UT4
5 6O
UT3
7O
UT2
8O
UT1
F502
GN
D
910 G
ND
IN1
12
C515
RE
SO
UT_N
HA
LL_SW
_LR
CV
-R
CV
+
D_L(5)
D_L(7)
D_L(6)
D_L(4)
D_L(2)
D_L(0)
D_L(12)
D_L(13)
D_L(14)
D_L(15)
D_L(10)
LED
_B
LCD
_WR
SC
AN
6
MA
IN_LC
D_C
S
SP
K_R
+S
PK
_R-
HA
LL_SW
_R
D_L(3)
D_L(1)
D_L(8)
D_L(11)
D_L(9)
LED
_RK
EY
SE
NS
E1
KE
YS
EN
SE
2M
AIN
_LCD
_BL
LED
_GS
CA
N5
LRS
D_L(8:15)
D_L(0:7)
SP
K_L-
SP
K_L+
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-7
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-8
This Document can not be used without Samsung's authorization
7-1-3 Speaker, Receiver and Mic Checking
Check HEA501and Receiver
Check mic path fromCN201 to U101 and it's
neighboring circuits.
Check SPK1, SPK2 pin1,2 onLCD signal OK?
Replace receiver
Check KEY FPCB
Insert Power
Receiver isOK?
MIC is OK?
Check CN201pin20, 22signal on?
Check HEA501pin 5, 7
signal OK?
Check HEA501pin45,46(Spk_R),pin47,48(Spk_L)
signal OK?
NO
Check U205and Speaker
NO
NO
END
YES
YES
YES
YES
YES
YES
Speaker isOK?
YES
NO
NO
NO
Replace Speaker
YES
Check LCDFPCB
NO
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-9
This Document can not be used without Samsung's authorization
(2.7V)
1 2 345
V205
C23
8
L203
C23
9
C23
7
C23
4
V207
1 2 345
V208
VBATT
C23
6
V_LED
33
44 5
566
7788
99
1818 19
19
22
2020 21
212222
232324
24
1010 11
1112
1213
131414 15
1516
16 1717
CN201
11
VPD
C23
5
C23
3
V206
1 2 345
HALL_FOLDER
KEYSENSE0KEYSENSE1KEYSENSE2KEYSENSE3
SCAN1
M_MIC
SCAN6SCAN5
SCAN2
SCAN4
SCAN0SCAN7
ON_SW
SCAN3
MIC-
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-10
This Document can not be used without Samsung's authorization
C250
C246
C257
L204
L205
C260
C273
C27
1
C255
C249
C274
L208
C245
R233
S3.6
C247
C256
C26
8
R230
R238
C254C253
C252
C26
9
C248
VDD
4VOMR
5VSS
6VOPR
7VDD
8VSS
9VDD
VSS21
VDD
22VIML
23VREFL
24VIPL
GND25
26NC
NC27
3
EN_R
14VSS
15VDD
16VOML
17VSS
18VOPL
19VDD
2VSS
20
U205
1EN_L
10VIMR
11VREFR
12VIPR
13
C258
L207
C259
R240
C27
2
C244
SPK_L+
SPK_L-SPK_R-SPK_R+
HPH_RAUDIO_EN
HPH_L
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-11
This Document can not be used without Samsung's authorization
(2.7V)
C512
C516
5O
UT4
OU
T36
OU
T27
OU
T18
F5039 GN
DG
ND
10
1IN
1
IN2
23IN
3
IN4
4
34IN
4O
UT4
5 6O
UT3
7O
UT2
8O
UT1
F501
GN
D
910 G
ND
1IN
1
2IN
2
IN3
U516
C513
C500
1234
56
78
* V504
VP
D
456
78
V500
*
123
C514
* V503
1234
56
78
C511
IN4
45
OU
T4
OU
T36
OU
T27
OU
T18
F500
9 GND
GN
D
10
1IN
1
IN2
23IN
3
G49
55
5050
66
778
89
9
G5152
4141
4242
4343
4444
4545
4646
4747
4848
49
3434
3535
3636
3737
3838
3939
44
4040
2727
2828
2929 3
3
3030
3131
3232
3333
2220
2021
2122
22
2323
2424
2525
2626
1213
1314
14
1515
1616
1717
1818
1919
HE
A501
11
1010
1111
12
S3.6
5678
*V
501
12
34
IN2
IN3
34IN
4O
UT4
5 6O
UT3
7O
UT2
8O
UT1
F502
GN
D
910 G
ND
IN1
12
C515
RE
SO
UT_N
HA
LL_SW
_LR
CV
-R
CV
+
D_L(5)
D_L(7)
D_L(6)
D_L(4)
D_L(2)
D_L(0)
D_L(12)
D_L(13)
D_L(14)
D_L(15)
D_L(10)
LED
_B
LCD
_WR
SC
AN
6
MA
IN_LC
D_C
S
SP
K_R
+S
PK
_R-
HA
LL_SW
_R
D_L(3)
D_L(1)
D_L(8)
D_L(11)
D_L(9)
LED
_RK
EY
SE
NS
E1
KE
YS
EN
SE
2M
AIN
_LCD
_BL
LED
_GS
CA
N5
LRS
D_L(8:15)
D_L(0:7)
SP
K_L-
SP
K_L+
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-12
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-13
This Document can not be used without Samsung's authorization
7-2. RX
7-2-1 CDMA/PCS mode
STARTCDMA/PCS mode
SVC &ROAM OK?
Check CDMA/PCSRx Path
Call OK?DVGA valueCheck OK?
Tx PathCheck OK?
Adjust DVGA byprogram
S1M8690X(U400)Check Adjust TX by
program
FER OK?Check RFR6000(U302),
MSM6500(U101)
End
NO
NO
NONO
NO
YES
YES
YES
YES
YES
1. visual check! (soldering)
2. S/W Mode Check : CDMA Mode Check
3. OSC302 Check : 19.2MHz
4. VCO(OSC301) voltage/frequence level check
Frequence : 1715MHz < f < 1788MHz
Supply Voltage: 2.75 ± 0.1V
Control Voltage: 0.4 ~ 2.3V
5. U301 LNA gain check
6. U403, U404 Check
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-14
This Document can not be used without Samsung's authorization
7-2-2 GPS Mode
START GPS
GPS RFPath Check
OK?
U405 Logic Checkpin1 pin6 pin9
GPS L L H
F303 Check
GPS_NV_ITEMCheck OK?
Adjust by program
End
YES
NO
YES
NO
1. visual check! (soldering)
2. S/W Test Mode Check : GPS Mode
3. OSC302 Check : 19.2MHz
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-15
This Document can not be used without Samsung's authorization
0 : G
PS
_EN
AB
LE1
: GP
S_D
ISA
BLE
2G 35G
1IN
4OUT
F303
G
C30
2
R30
8
C31
0
C362
L313
C358
C34
5
C355
C356
V_T
CX
O
L323
OU
T
3S
WV
C5
VC
C7
R344
OS
C30
1 G 8
G 64G 2G1
D2G 4
S1 13S2ATF-55143
Q302
C31
2
R343
R31
2C
338
C30
4
G5
IN1
3O
UT
OU
T4
1V
CO
N
F302
2 G
OS
C30
3
2GN
D
3 OU
TV
CC
4
C31
4
C32
5
R345
L304
C32
4L321
R31
0
C32
0
R30
3
R30
9
V_RFRX
R30
7
L308
C30
6
C33
6
C30
1
C31
3
C354
L309
R30
2
C31
5
C32
6
R30
5
C361
L322
2.7D
V_B
T
C30
8
R346
C30
9
C33
2
C31
7
R30
0
L314
C34
0
C30
7
C33
3
L303
L301
C30
5
R30
6
C33
4
C30
0
V_R
FRX
C34
4
C32
1
L311
C363
50V
C34
1
L324
V_R
FRX
L306
C32
3
VP
D
PLN
A_IN
4
GN
D5
FM_STEP6
SPI_CLK7
SPI_EN8
VDDM9
14G
ND
VDDA15
RBIAS16
GND17
NC18
NC19
CLN
A_IN
BIAS
2
PLN
A_IN
BIAS
3
U30
1FC
7510
CLN
A_IN
1
SPI_DT10
PLN
A_O
UT
11G
ND
12C
LNA_
OU
T13
5
IN1
3O
UT
OU
T4
VP
D
F3012 G
G
C32
2
Q30
11
32
C31
6
L310
V_T
CX
O
L305
C31
1
L302
28VD
DA1
14
VDDA121718VDDA13
VDD
A14
29
VDDA2114
39 VDDA22
27VD
DA3
20VDDA4
23VD
DM
46 8PC
S_IN
M
6PC
S_IN
P
30R
X_IM
RX_
IP31
33 RX_QM
34 RX_QP
38 R_BIAS
25SB
CK
26SB
DT
24SB
ST
TCXO
32 GND9
GPS
_IN
M10
12GPS_INP
GVC
O_T
UN
E21
15LO_INM
LO_INP16
LO_OUT19
36 NC1
NC237
45 NC3NC4
GND11
42 GND12
43 GND13GND144
4
GN
D2
3 5G
ND
3
GN
D4
7
GN
D5
9 11G
ND
6GND713
22G
ND
8
RFR
6000
U30
2
40 CELL_INM
CEL
L_IN
P2
GN
D1
1
35 GND10
41
C31
8
L312
R30
4
L300
C30
3
L307
R30
1
C31
9
C32
7
GPS_RX
GPS_MODE
SBI_CK
SBI_DT
SBI_ST
BT_
CLK
_EN
TCX
O_B
T
EX
T_V
CO
_EN
CP
_RX
RX
_Q_N
RX
_Q_P
RX
_I_P
RX
_I_N
UH
F_LO
_BU
FF
SB
I_S
T
SB
I_C
K
SB
I_D
T
CE
LL_R
X
PC
S_R
X
TCX
O
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-16
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-17
This Document can not be used without Samsung's authorization
7-3 Tx
7-3-1 CDMA/PCS mode
CheckS1M8690X(U400)
pin30(R403)OK?
CheckS1M8690X(U400)P_OUTB(C414)C_OUT(C430)RF OUT Level
OK?
YES
NO
CheckPLLOK?
CheckPCS:PA(U404)
CDMA:PA(U403)Output Level
CDMA/PCS AbnormalTransmitter section
NONO
NO
NO
End
YES
NO
YES
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-18
This Document can not be used without Samsung's authorization
(2.85V)
C436
C413
C405
AN
T402
R409
C402
R402
C447
L400
C429
C438
V_R
FTX
VD
D2
6
13
GND
14
GND
15
GND
RFIN
4
RFO
UT
8
1V
BIA
S
VC
NTL
25V
DD
1
3G
ND
GND
16
7G
ND
9G
ND
GN
D10
11
GNDGND
12
VP
D
V_S
YN
TH
U403
C411
C435
L404
L401
C423
C446
L403
C418
L402
C448
C408
U401
KM
S-512
2 A
C3
G1
G4
C449
AN
T401
C450
C434
R404
C416
C440
C407
C441
C421
R405
VDDA39
40
VDDA40
7V
DD
A7
1V
DD
MC
424
17
VDDA17
22V
DD
A22
24V
DD
A24
26V
DD
A26
28V
DD
A28
31V
DD
A31
32VDDA32
39
4S
BD
T
5S
BS
T
8TC
XO
10TX
_CP
30V
CN
TL
12 VDDA12
13 VDDA13
14 VDDA14
16 VDDA16
20
21N
C
2P
A_O
N
25P
_OU
TA
P_O
UTB
27
19 RX_CP
15 RX_LO
3S
BC
K
I_IN
35I_IP
34I_QN
33
I_QP
6LO
CK
9N
C
11N
C
18 NC
NC
38BIAS
23C
_OU
T
41
GND
42
GNDGND 43
29G
ND
37IREF
36
U400
C412
C419
C400
C401
C404
TX1
C415
F402
AN
T3 4G
ND
2R
X
C422
R406
C451
C417
2G
ND
1G
ND
24
1IN
3O
UT
C437
F404
R408
R410
V_S
YN
TH
C414
C442
C420
C426
C410
G4G5
67 G6 G7
9 G81012
G9
RX
5TX
11
F4058AN
T
G11
G10
132
G2G3
34C
432C
433
C430
R400
R411
R401
9V
1
V2
6
V3
1
7
10
NC
12
NC
NC
1415
NC
RF1
8
RF2
5
RF3
2U
405 ANT 1113
GND
3N
C
NC
4
NC
C403
C406
C425
C444
10V
DD
2
R407
12
GNDGND
1314
GNDGND
15
2R
FIN
8R
FOU
T
VB
IAS
5 4V
CN
TL
VD
D1
1
GN
D3
16
GND
6G
ND
GN
D7
GN
D9
GND
11
C409
U404
C439
C445
C428
R403
4G
ND
2
IN13
OU
T
C431
C443
F401
GN
D1
2
C427
AN
T
CE
LL_RX
PC
S_R
X
GP
S_M
OD
E
CP
_RX
GP
S_R
X
PC
S_M
OD
E
CD
MA
_MO
DE
UHF_LO_BUFF
TX_Q
_P
TX_Q
_N
TX_I_P
TX_I_N
DA
C_R
EF
AU
X_S
BI_S
T
AU
X_S
BI_D
T
AU
X_S
BI_C
K
TX_O
NTX
_AG
C_A
DJ
TCX
O
PA
M_V
DD
PA
_ON
_CE
LL
PA
_ON
_PC
S
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-19
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-20
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-21
This Document can not be used without Samsung's authorization
7-4 Camera checking
Insert Power
YES
Check HEA502,HIOVDD(R522),15V(C562) and-8V(C563) OK?
CameraPreview is
OK?
Check U500,U501, and U502
NO
NO
NO
YES
YES
YES
YES
YES
END
NO
NO
CheckM_DRV(C564),HIOVDD(R522),
CameraFlash is OK?
Auto Focus& Optical
Zoom is OK?
Replace Camera module
Replace Camera module
Check U504and U502
YES
NO
Replace Flash FPCB
Check U211
CheckV_FLASH_5V
(C210)
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-22
This Document can not be used without Samsung's authorization
CAMERA & FLASH
(3.1V)(3.1V)
(3.1V)
(3.1V)
(3.1V)
C55
9
C54
9
99
11NC NC
12
C56
3
10 10
2233 4 455 6 677 8 8
HEA503AXK8L10125SJ
11
C524
VC04
0205
X15
0RV5
07
C540
C534C
560
C504
C56
2
C501
S3.6
R510
10V10UFC528
C533
33PF50V
CUS02D503
C531
1
3 VOUT
HIOVDD
C56
1
U511
CE 6
2 GND 5GND
NC 4
VDD
R543R544
R542
R541
R540
R508
50V
C53
056
PF
R503
HIOVDD
C523
C54
7
M_DRV
C519
L509
C56
4
R504
R502
L505
ACZ1005M-152-T
HIOVDD
C508
U502
BP 43 EN
GND2
VIN1
VOUT 5
R521
C541
D504CUS02
C522
C518
C520
C502
R511
V505
VC
0402
05X1
50R
C55
6
R522
HIOVDD
VIO
C55
4
CE 6
2 GND 5GND
NC 4
VDD1
3 VOUT
U512
C55
3
S3.6
C54
8
C505
C54
5
C55
7
EN3
GND2 GND 5
6NC
VIN 4
1 VOUT
U501
3132N
C30 30
44556 6
778899
NC
23232424252526 26
27 2728282929
33
161617 1718 18
1919
2 2
202021 2122 22
11
10 1011111212
13 1314 141515
HEA502
C54
6
C529
U515
S3.6
S3.6
C517
RB520S-30D502
HIOVDD
L510
C507
C535
3
2GND
VIN1
VOUT 5
S3.6
U504
BP 4EN
V508
VC04
0205
X15
0R
C55
8
56PFC532
C506
50V
C55
2
VNEG
23
VPO
S
VREF17
C55
5
NC
OUTN14
13 OUTN
PGND2
PGND3
PSN
11PS
P9
4VIN
15
GN
D
INN5
INN6
INP1
INP
24
12
NC
20
NC
NC
26 2719
7
BSW
18 CN
CP
21
10
ENN
ENP
8
16 FBN
22
FBP
25
U500AG
ND
C525
MV_CAM_SDA
M_CAM_SDA
M_CAM_SCL
HREF
VSYNCPCLK
CAM_HSYNC
C55
1
V_FLASH_5VFLASH-
V_MOTOR
3.0AV
1.8V_ON
3.0AV_ON
CAM_DINT2
D_CAM(0)D_CAM(2)D_CAM(4)D_CAM(6)
D_CAM(3)D_CAM(5)D_CAM(7)
PS-8V_ON
15V_ON
1.8V
CAM_PCLK
D_CAM(1)
CAM_VSYNC
MV_CAM_SCL
CAM_RESETB
CAM_MCLK
CAM_MOT_ON
M_DRV
VIO
CAM_VIO_EN
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-23
This Document can not be used without Samsung's authorization
L200
S3.6
C275
R202
C211
R204R205
C209C200
C210
ISET2
6
9VIN
10C2M
CPO
3
7 EN1
8 EN2
11GND
GND 13
ILED 5
ISET1
4
U211
2C1+
12
C1M C2+
1
R203
FLASH_PULSE
CAM_FLASH_ON
V_FLASH_5V
FLASH-
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-24
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-25
This Document can not be used without Samsung's authorization
7-5 Bluetooth checking
Sleep Xtal(R324) OK?
Check PMICU203
Replace Sleep Xtal OSC101
Replace OSC303
Replace U306
Insert PowerEnter Test Mode
(4,7,*8,6,9,#,1,2,3,5)BT RF On (001→027)
TCXO_BT(C341) OK?
BT module(pin 25) OK?
Check2.7DV_BT,
1.8DV_BT(L316)
Check2.7DV_BT
(L319) NO
NO
END
YES
YES
YES
YES
YES
YES
NO
NO
NO
Check PMICU203
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-26
This Document can not be used without Samsung's authorization
C345
AN30013 2
2.7DV_BT
TX_PU_TDD_N 23
10V_I_O
16 XTAL_IN
XTAL_OUT15
3 NC
NC4
8 NC
REG_CTRL 6
RESET_N 22
TM018
19 TM1_2
TM320
1 GND
GND14
GND17
24 GND
GND26
35 GND
LPO_IN 12
NC2
BLUE_HOST_WAKE 9
31BLUE_RTS
BLUE_RX 33
5BLUE_TX
11BLUE_WAKE
BTL_REG34
21BTRF_REG
EEPROM_CLK7
25 ANT_MATCH
ASAP_CLK 27
ASAP_FS 28
ASAP_RX 30
ASAP_TX 32
BLUE_CLK_EN13
29BLUE_CTS
U306
R311
1VCON
OSC303
2GND
3OUTVCC
4
C343
C350
C364
R325
2.7DV_BT
C344
C341
C3422.7DV_BT
R324
Q3011
3
2
C366
R3141.8DV_BT
BT_RESET
BT_WAKE
SLEEP_XTAL_OUT
BT_TXD
BT_RXD
BT_RTS
BT_CTS
BT_CLK_EN
BT_CLK_EN
TCXO_BT
TCXO_BT
HOST_WAKE
AUX_PCM_CLK_BT
AUX_PCM_SYNC_BT
AUX_PCM_DIN_BT
AUX_PCM_DOUT_BT
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-27
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
Flow Chart of Troubleshooting
7-28
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
8. Exploded Views and Parts List
8-1
This Document can not be used without Samsung's authorization
8-1. Exploded Views
QWD02
QWD03
QFU01
QKP02
QME04
QCR05
QLB01
QSP01QAU01
QFU03
QSC12
QCW03
QRH01
QFL01
QCR16
QCW08
QSC11
QCR08
QSC14
QCR43
QMP02
QME01
QMP01
QRE02
QCR12
QAN02
QRE01
QBA01
QVO01
QSC08
QRF01
QCR53
QFR02
QKP01
QCK02
QME03
QCK07
QSP02
QSC04
QRF03
QFR01
QCK08
QCW01
QCK04QCA01QCR06
QCW04
QIF01
QMW02
QCK01
QCH08QCW02
SAMSUNG Proprietary-Contents may change without notice
Exploded views and Parts List
8-2
This Document can not be used without Samsung's authorization
8-2. Parts ListLocation No Description Sec CodeQAN02 INTENNA-SPHA940 GH42-00659A
QAU01 AUDIO-RECEIVER 3009-001104
QBA01 BATTERY-1000MAH,SIL,ENG,M GH43-02160A
QCA01 UNIT-CAMERA GH59-01626A
QCH08 RMO-RUBBER KEY CAMERA GH73-04179A
QCK01 MEC-CAMERA KEY DUMMY GH75-06362A
QCK02 PMO-KEY CAMERA GH72-19429A
QCK04 MEC-CAMERA BRACKET GH75-07532A
QCK07 MEC-CAMERA KEY FIX GH75-07513A
QCK08 MEC-CAMERA DUMMY GH75-07979A
QCR05 SCREW-MACHINE 6001-001478
QCR06 SCREW-MACHINE 6001-001155
QCR12 SCREW-MACHINE 6001-001530
QCR16 SCREW-MACHINE 6001-001878
QCR43 SCREW-MACHINE 6001-001413
QCR53 SCREW-MACHINE 6001-001639
QCW01 PCT-CAMERA LENS GH72-19798A
QCW02 PMO-CAMERA KEY DECO GH72-23056A
QCW03 PMO-ROTARY RING GH72-19156A
QCW08 ICT-ROTARY HINGE WASHER GH70-00364A
QFR02 MEC-SHIELD CAN FRONT GH75-06708A
QFU01 MEC-FOLDER UPPER GH75-06350A
QFU03 MEC-FOLDER DUMMY GH75-06353A
QKP01 MEC-KEYPAD MAIN GH75-06355A
QKP02 MEC-KEY FOLD GH75-06354A
QLB00 MEC-LCD BRACKET GH75-06352A
QME01 UNIT-KEY FPCB GH59-02401A
QME03 UNIT-FLASH FPCB GH59-02399A
QME04 UNIT-MOD KEY GH59-02400A
QMP01 PBA MAIN-SPHA940 GH92-02289A
QMP02 PBA ETC-LCD MODULE GH92-02306A
QMW02 PCT-MAIN WINDOW GH72-19431A
QRE02 MEC-SHIELD CAN REAR GH75-06709A
QRF01 MPR-SHEET RF COVER GH74-16885A
QSC04 RMO-F/LOWER SCREW CAP GH73-04955A
QSC08 RMO-RUBBER R/SCREW CAP GH73-05004A
QSC11 MPR-FOLDER DUMMY COVER R GH74-16044A
QSC12 MPR-FOLDER DUMMY COVER L GH74-16045A
QSC14 PMO-F/D HOLE COVER GH72-19099A
QSP01 SPEAKER 3001-001817
QSP02 SPEAKER 3001-001816
QVO01 PMO-SIDE KEY GH72-23246A
QWD02 PCT-SUB WINDOW GH72-19432A
QWD03 PMO-DUAL WINDOW DECO GH72-23251A
QRE01 MEC-REAR COVER GH75-06349A
QIF01 PMO-IF COVER GH72-23249A
QFL01 MEC-FOLDER LOWER GH75-07830A
QCR08 SCREW-MACHINE 6001-001456
QRH01 MEC-ROTARY HINGE GH75-06361A QCW08 ICT-ROTARY HINGE WASHER GH70-00364A
QFR01 MEC-FRONT COVER GH75-06351A QRF03 PMO-EAR COVER GH72-23362A
QCW04 PMO-TFR COVER GH72-19109A
SAMSUNG Proprietary-Contents may change without notice
Exploded views and Parts List
8-3
This Document can not be used without Samsung's authorization
Description Sec CodeIC-MEMORY CARD 1109-001313
CONNECTOR-ADAPTOR 3719-001319
BAG PE 6902-000297
BAG PE 6902-000643
BAG ZIPPER 6902-000683
CBF SIGNAL-SPHA940 DANPLA GH39-00466A
CHARGER-SCHA970 DTC GH44-00909A
UNIT-EARPHONE GH59-02008A
LABEL(P)-GUIDE(SPRINT) GH68-02023A
LABEL(P)-WATER SOAK GH68-02026A
LABEL(R)-MAIN(SPRINT) GH68-06665A
MANUAL-SPRINT ACTIVATION GH68-07877A
MANUAL-TERMS AND COMDITION GH68-07930A
MANUAL-POWER VISION CARD GH68-08092A
CUSHION-CASE GH69-02740A
BOX(P)-UNIT(SPRINT) GH69-02741A
PMO-SERVICE LED GH72-19427A
RMO-RUBBER HOLDER VIBRAT GH73-04231A
MPR-CONTACT VINYL GH74-07554A
MPR-TAPE SUB WINDOW GH74-12874A
MPR-TAPE LCD C GH74-13240A
MPR-TAPE LCD A GH74-15767A
MPR-GASKET CAM BRK GH74-15982A
MPR-GASKET LCD CON GH74-15983A
MPR-TAPE ROTARY SHAFT GH74-15984A
MPR-TAPE MAIN PCB IF GH74-15988A
MPR-TAPE MAIN KEY PCB TO GH74-15989A
MPR-TAPE CAM FPCB GH74-15990A
MPR-TAPE LCD CON 2 GH74-15991A
MPR-TAPE LCD CON 3 GH74-15992A
MPR-GASKET KEY FPCB GH74-15995A
MPR-BOHO VINYL C/LENS A GH74-16082A
MPR-BOHO VINYL C/LENS B GH74-16083A
MPR-BOHO VINYL C/LENS C GH74-16084A
MPR-BOHO VINYL F/UPPER A GH74-16085A
MPR-BOHO VINYL F/UPPER B GH74-16086A
MPR-BOHO VINYL F/LOWER A GH74-16087A
MPR-BOHO VINYL F/LOWER B GH74-16088A
MPR-BOHO VINYL F/U C GH74-17102A
MPR-BOHO VINYL F/L C GH74-17104A
MPR-TAPE MAIN SHIELD GH74-17105A
MPR-TAPE KEY MOD FPCB GH74-17168A
MPR-TAPE ZIP TYPE CON GH74-17178A
MPR-BOHO VINYL CAM LENSD GH74-17472A
PAA ETC-SPH A940(XAR) GH99-11282A
SAMSUNG Proprietary-Contents may change without notice
Exploded views and Parts List
8-4
This Document can not be used without Samsung's authorization
8-3 DM Cable(GH39-00129A) 8-4 Test JIG
8-5 RF Cable(GH39-00397A) 8-6 Test Jig Cable(GH39-00399A)
SAMSUNG Proprietary-Contents may change without notice
9. Block Diagram
9-1
This Document can not be used without Samsung's authorization
S/W
CellDUP
PCSDUP
CellBPF
PCSBPF
RFT6100
RFL6000
CellBPF
PCSBPF
RFR6000
Cell PA
PCS PA
GPSBPF
VCO
VC-TCXO
PLL
GPS LNA
Tx
Tx
Rx
Rx
ANT
MSM6500
Power IC
Memory1024MB NAND
+ 512MB SDRAM
Bluetooth Module
BluetoothANT
UART, PCM I/F
LCD
Camera
RF part
SAMSUNG Proprietary-Contents may change without notice
10. Electrical Parts List
10-1
This Document can not be used without Samsung's authorization
Design LOC Description SEC CODE STATUS
AN300 ANTENNA-CHIP 4202-001065 SAC100 C-CER,CHIP 2203-005393 SAC101 C-CER,CHIP 2203-005393 SAC102 C-CER,CHIP 2203-000812 SAC103 C-CER,CHIP 2203-000812 SAC104 C-CER,CHIP 2203-005061 SAC105 C-CER,CHIP 2203-006093 SAC106 C-CER,CHIP 2203-005061 SAC107 C-CER,CHIP 2203-000254 SAC108 C-CER,CHIP 2203-005061 SAC109 C-CER,CHIP 2203-000254 SAC110 C-CER,CHIP 2203-005061 SAC111 C-CER,CHIP 2203-000254 SAC112 C-CER,CHIP 2203-005061 SAC113 C-CER,CHIP 2203-000254 SAC114 C-CER,CHIP 2203-005061 SAC116 C-CER,CHIP 2203-001072 SAC117 C-CER,CHIP 2203-000254 SAC118 C-CER,CHIP 2203-005061 SAC119 C-CER,CHIP 2203-000254 SAC12 C-CER,CHIP 2203-006399 SAC120 C-CER,CHIP 2203-005061 SAC121 C-CER,CHIP 2203-000233 SAC123 C-CER,CHIP 2203-000254 SAC124 C-CER,CHIP 2203-000254 SAC125 C-CER,CHIP 2203-000254 SAC126 C-CER,CHIP 2203-000254 SAC127 C-CER,CHIP 2203-005061 SAC13 C-CER,CHIP 2203-006399 SAC131 C-CER,CHIP 2203-000679 SAC132 C-CER,CHIP 2203-000679 SAC133 C-CER,CHIP 2203-006093 SAC134 C-CER,CHIP 2203-006053 SAC135 C-CER,CHIP 2203-005482 SAC136 C-CER,CHIP 2203-001405 SAC137 C-CER,CHIP 2203-001405 SAC138 C-CER,CHIP 2203-001405 SAC139 C-CER,CHIP 2203-001405 SAC14 C-CER,CHIP 2203-006399 SAC140 C-CER,CHIP 2203-005061 SAC141 C-CER,CHIP 2203-005061 SAC142 C-CER,CHIP 2203-006091 SAC143 C-CER,CHIP 2203-000812 SAC144 C-CER,CHIP 2203-000812 SAC145 C-CER,CHIP 2203-000812 SAC146 C-CER,CHIP 2203-006091 SAC147 C-CER,CHIP 2203-005061 SAC149 C-CER,CHIP 2203-005061 SAC15 C-CER,CHIP 2203-005065 SAC150 C-CER,CHIP 2203-005061 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-2
Design LOC Description SEC CODE STATUS
C152 C-CER,CHIP 2203-005061 SAC153 C-CER,CHIP 2203-005061 SAC154 C-CER,CHIP 2203-005061 SAC155 C-CER,CHIP 2203-005061 SAC157 C-CER,CHIP 2203-000233 SAC159 C-CER,CHIP 2203-000254 SAC16 C-CER,CHIP 2203-005061 SAC160 C-CER,CHIP 2203-000254 SAC161 C-CER,CHIP 2203-005509 SAC162 C-CER,CHIP 2203-000254 SAC163 C-CER,CHIP 2203-001432 SAC164 C-CER,CHIP 2203-001432 SAC165 C-CER,CHIP 2203-001432 SAC166 C-CER,CHIP 2203-005482 SAC167 C-CER,CHIP 2203-005509 SAC168 C-CER,CHIP 2203-000885 SAC169 C-CER,CHIP 2203-000254 SAC17 C-CER,CHIP 2203-005061 SAC170 C-CER,CHIP 2203-005061 SAC171 C-CER,CHIP 2203-005061 SAC172 C-CER,CHIP 2203-000995 SAC173 C-CER,CHIP 2203-000254 SAC174 C-CER,CHIP 2203-006093 SAC175 C-CER,CHIP 2203-006093 SAC18 C-CER,CHIP 2203-005061 SAC19 C-CER,CHIP 2203-005061 SAC20 C-CER,CHIP 2203-000995 SAC200 C-CER,CHIP 2203-005482 SAC201 C-CER,CHIP 2203-006329 SAC202 C-TA,CHIP 2404-001274 SAC203 C-CER,CHIP 2203-000254 SAC204 C-CER,CHIP 2203-006348 SAC205 C-CER,CHIP 2203-005061 SAC206 C-TA,CHIP 2404-001381 SAC207 C-TA,CHIP 2404-001274 SAC208 C-CER,CHIP 2203-006324 SAC209 C-CER,CHIP 2203-006201 SAC21 C-CER,CHIP 2203-000995 SAC210 C-CER,CHIP 2203-006329 SAC211 C-CER,CHIP 2203-006324 SAC212 C-CER,CHIP 2203-000254 SAC213 C-CER,CHIP 2203-001652 SAC214 C-CER,CHIP 2203-000585 SAC215 C-CER,CHIP 2203-006201 SAC216 C-CER,CHIP 2203-000585 SAC217 C-CER,CHIP 2203-006201 SAC218 C-CER,CHIP 2203-000438 SAC219 C-CER,CHIP 2203-005664 SAC22 C-CER,CHIP 2203-000995 SAC220 C-CER,CHIP 2203-005664 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-3
Design LOC Description SEC CODE STATUS
C221 C-TA,CHIP 2404-001105 SAC222 C-CER,CHIP 2203-006201 SAC223 C-CER,CHIP 2203-006201 SAC224 C-CER,CHIP 2203-006053 SAC225 C-CER,CHIP 2203-006053 SAC226 C-CER,CHIP 2203-006201 SAC227 C-CER,CHIP 2203-006324 SAC228 C-CER,CHIP 2203-006324 SAC229 C-CER,CHIP 2203-005061 SAC23 C-TA,CHIP 2404-001225 SAC230 C-CER,CHIP 2203-005061 SAC231 C-CER,CHIP 2203-005061 SAC233 C-CER,CHIP 2203-005482 SAC234 C-CER,CHIP 2203-005482 SAC235 VARISTOR 1405-001110 SAC236 VARISTOR 1405-001138 SAC237 VARISTOR 1405-001138 SAC238 VARISTOR 1405-001138 SAC239 C-CER,CHIP 2203-005482 SAC240 C-CER,CHIP 2203-006053 SAC241 C-TA,CHIP 2404-001305 SAC242 C-TA,CHIP 2404-001305 SAC243 C-CER,CHIP 2203-000812 SAC244 C-CER,CHIP 2203-000233 SAC245 C-CER,CHIP 2203-000233 SAC246 C-CER,CHIP 2203-000233 SAC247 C-CER,CHIP 2203-000233 SAC248 C-CER,CHIP 2203-005480 SAC249 C-CER,CHIP 2203-005480 SAC250 C-CER,CHIP 2203-005480 SAC251 C-CER,CHIP 2203-005482 SAC252 C-CER,CHIP 2203-005480 SAC253 C-CER,CHIP 2203-000812 SAC254 C-CER,CHIP 2203-000812 SAC255 C-CER,CHIP 2203-000438 SAC256 C-CER,CHIP 2203-000438 SAC257 C-CER,CHIP 2203-005482 SAC258 C-TA,CHIP 2404-001347 SAC259 C-CER,CHIP 2203-005061 SAC260 C-CER,CHIP 2203-005061 SAC261 C-CER,CHIP 2203-005482 SAC262 C-CER,CHIP 2203-000940 SAC263 C-CER,CHIP 2203-000233 SAC264 C-CER,CHIP 2203-000438 SAC265 C-CER,CHIP 2203-005061 SAC266 C-CER,CHIP 2203-000254 SAC267 C-CER,CHIP 2203-000812 SAC268 C-CER,CHIP 2203-000438 SAC269 C-CER,CHIP 2203-000438 SAC270 C-TA,CHIP 2404-001381 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-4
Design LOC Description SEC CODE STATUS
C271 C-CER,CHIP 2203-000812 SAC272 C-CER,CHIP 2203-000812 SAC273 C-CER,CHIP 2203-006093 SAC274 C-CER,CHIP 2203-006093 SAC275 C-CER,CHIP 2203-006324 SAC276 C-CER,CHIP 2203-006090 SAC277 C-CER,CHIP 2203-006090 SAC300 C-CER,CHIP 2203-006201 SAC301 C-CER,CHIP 2203-000233 SAC302 C-CER,CHIP 2203-006201 SAC303 C-CER,CHIP 2203-000995 SAC306 C-CER,CHIP 2203-000233 SAC307 C-CER,CHIP 2203-001017 SAC308 C-CER,CHIP 2203-000438 SAC309 C-CER,CHIP 2203-005061 SAC310 C-CER,CHIP 2203-001017 SAC311 C-CER,CHIP 2203-005446 SAC312 C-CER,CHIP 2203-000438 SAC313 C-CER,CHIP 2203-000438 SAC314 C-CER,CHIP 2203-000438 SAC315 C-CER,CHIP 2203-005061 SAC318 C-CER,CHIP 2203-005446 SAC319 C-CER,CHIP 2203-000438 SAC320 C-CER,CHIP 2203-005482 SAC321 C-CER,CHIP 2203-000233 SAC322 C-CER,CHIP 2203-005061 SAC323 C-CER,CHIP 2203-000995 SAC324 C-CER,CHIP 2203-006093 SAC325 C-CER,CHIP 2203-000233 SAC326 C-CER,CHIP 2203-005061 SAC327 C-CER,CHIP 2203-000995 SAC332 C-TA,CHIP 2404-001381 SAC333 C-CER,CHIP 2203-005061 SAC334 C-CER,CHIP 2203-005482 SAC336 C-CER,CHIP 2203-000995 SAC338 C-CER,CHIP 2203-000995 SAC340 C-CER,CHIP 2203-005061 SAC341 C-CER,CHIP 2203-000438 SAC342 C-CER,CHIP 2203-006201 SAC343 C-CER,CHIP 2203-006053 SAC344 C-CER,CHIP 2203-005065 SAC345 C-CER,CHIP 2203-000438 SAC346 C-CER,CHIP 2203-006093 SAC347 C-CER,CHIP 2203-005482 SAC348 C-CER,CHIP 2203-000233 SAC349 C-CER,CHIP 2203-000254 SAC350 C-CER,CHIP 2203-006201 SAC354 C-CER,CHIP 2203-000438 SAC355 C-CER,CHIP 2203-005050 SAC356 C-CER,CHIP 2203-000233 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-5
Design LOC Description SEC CODE STATUS
C358 C-CER,CHIP 2203-000870 SAC361 C-CER,CHIP 2203-000233 SAC363 C-CER,CHIP 2203-006093 SAC364 C-CER,CHIP 2203-006208 SAC366 C-CER,CHIP 2203-006208 SAC400 C-CER,CHIP 2203-000585 SAC401 C-CER,CHIP 2203-000995 SAC402 C-CER,CHIP 2203-005482 SAC403 C-CER,CHIP 2203-000585 SAC404 C-CER,CHIP 2203-000233 SAC406 C-CER,CHIP 2203-002677 SAC407 C-CER,CHIP 2203-000885 SAC408 C-CER,CHIP 2203-000995 SAC409 C-CER,CHIP 2203-005061 SAC410 C-CER,CHIP 2203-006201 SAC411 C-CER,CHIP 2203-000233 SAC412 C-CER,CHIP 2203-000885 SAC413 C-CER,CHIP 2203-001072 SAC414 C-CER,CHIP 2203-001178 SAC415 C-CER,CHIP 2203-000885 SAC416 C-CER,CHIP 2203-006201 SAC417 C-CER,CHIP 2203-000885 SAC418 C-CER,CHIP 2203-000940 SAC419 C-CER,CHIP 2203-000885 SAC420 C-CER,CHIP 2203-000885 SAC421 C-CER,CHIP 2203-000940 SAC422 C-TA,CHIP 2404-001352 SAC423 C-CER,CHIP 2203-000233 SAC424 C-CER,CHIP 2203-005061 SAC425 C-CER,CHIP 2203-000233 SAC426 C-CER,CHIP 2203-000885 SAC429 C-CER,CHIP 2203-000438 SAC430 C-CER,CHIP 2203-001259 SAC431 C-CER,CHIP 2203-000438 SAC432 C-CER,CHIP 2203-005234 SAC434 C-CER,CHIP 2203-000254 SAC435 C-CER,CHIP 2203-000254 SAC436 C-CER,CHIP 2203-000233 SAC437 C-CER,CHIP 2203-000679 SAC438 C-CER,CHIP 2203-000679 SAC439 C-CER,CHIP 2203-002687 SAC440 C-CER,CHIP 2203-000254 SAC441 C-CER,CHIP 2203-000885 SAC442 C-CER,CHIP 2203-005480 SAC443 C-CER,CHIP 2203-006190 SAC445 C-CER,CHIP 2203-001072 SAC446 C-CER,CHIP 2203-000940 SAC447 C-CER,CHIP 2203-000254 SAC448 C-CER,CHIP 2203-000679 SAC449 C-CER,CHIP 2203-005061 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-6
Design LOC Description SEC CODE STATUS
C450 C-CER,CHIP 2203-006201 SAC451 C-CER,CHIP 2203-005482 SAC452 C-CER,CHIP 2203-006324 SAC453 C-CER,CHIP 2203-006208 SAC454 C-CER,CHIP 2203-006190 SAC455 C-CER,CHIP 2203-000138 SAC500 C-CER,CHIP 2203-001072 SAC501 C-CER,CHIP 2203-006427 SAC502 C-CER,CHIP 2203-006427 SAC503 C-CER,CHIP 2203-005061 SAC504 C-CER,CHIP 2203-000254 SAC505 C-CER,CHIP 2203-006190 SAC506 C-CER,CHIP 2203-000885 SAC507 C-TA,CHIP 2404-001374 SAC508 C-CER,CHIP 2203-006427 SAC511 C-CER,CHIP 2203-006093 SAC512 C-CER,CHIP 2203-006093 SAC513 C-CER,CHIP 2203-001072 SAC514 C-CER,CHIP 2203-001072 SAC515 C-CER,CHIP 2203-001072 SAC516 C-CER,CHIP 2203-001072 SAC517 C-CER,CHIP 2203-006093 SAC518 C-CER,CHIP 2203-006093 SAC519 C-CER,CHIP 2203-006093 SAC520 C-CER,CHIP 2203-006093 SAC522 C-CER,CHIP 2203-006137 SAC523 C-CER,CHIP 2203-006201 SAC524 R-CHIP 2007-000162 SAC525 C-CER,CHIP 2203-006093 SAC526 C-CER,CHIP 2203-005061 SAC527 C-TA,CHIP 2404-001105 SAC528 C-TA,CHIP 2404-001381 SAC529 C-CER,CHIP 2203-006137 SAC530 C-CER,CHIP 2203-001072 SAC531 C-CER,CHIP 2203-000812 SAC532 C-CER,CHIP 2203-001072 SAC533 C-CER,CHIP 2203-006201 SAC534 R-CHIP 2007-000162 SAC535 C-CER,CHIP 2203-006093 SAC536 C-CER,CHIP 2203-005061 SAC537 C-TA,CHIP 2404-001105 SAC538 C-CER,CHIP 2203-005061 SAC539 C-TA,CHIP 2404-001105 SAC540 C-CER,CHIP 2203-006093 SAC541 C-CER,CHIP 2203-006093 SAC542 C-CER,CHIP 2203-005061 SAC543 C-TA,CHIP 2404-001105 SAC544 C-CER,CHIP 2203-000254 SAC545 C-CER,CHIP 2203-000628 SAC546 C-CER,CHIP 2203-000386 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-7
Design LOC Description SEC CODE STATUS
C547 C-CER,CHIP 2203-000386 SAC548 C-CER,CHIP 2203-000386 SAC549 C-CER,CHIP 2203-000386 SAC551 C-CER,CHIP 2203-000628 SAC552 C-CER,CHIP 2203-000628 SAC554 C-CER,CHIP 2203-000386 SAC555 C-CER,CHIP 2203-000628 SAC556 C-CER,CHIP 2203-000628 SAC557 C-CER,CHIP 2203-000386 SAC558 C-CER,CHIP 2203-000386 SAC559 C-CER,CHIP 2203-000386 SAC560 C-CER,CHIP 2203-000386 SAC561 C-CER,CHIP 2203-000628 SAC562 C-CER,CHIP 2203-006348 SAC563 C-CER,CHIP 2203-006053 SAC564 C-CER,CHIP 2203-006093 SAC565 C-CER,CHIP 2203-000438 SACN1 CONNECTOR-FPC/FFC/PIC 3708-001912 SACN201 HEADER-BOARD TO BOARD 3711-005210 SACN204 CONNECTOR-BATTERY 3711-005732 SACN205 JACK-DC POWER 3722-002119 SACON10 CONNECTOR-CARD EDGE 3709-001344 SACON20 CONNECTOR-INTERFACE 3710-001611 SAD201 DIODE-SWITCHING 0401-001110 SAD202 DIODE-SWITCHING 0401-001110 SAD203 DIODE-ARRAY 0407-001002 SAD204 DIODE-TVS 0406-001178 SAD205 DIODE-TVS 0406-001150 SAD502 DIODE-SCHOTTKY 0404-001172 SAD503 DIODE-SCHOTTKY 0404-001245 SAD504 DIODE-SCHOTTKY 0404-001245 SAEAR20 JACK-EAR PHONE 3722-002315 SAF12 BEAD-SMD 3301-001342 SAF301 FILTER-SAW 2904-001521 SAF302 FILTER-SAW 2904-001519 SAF303 FILTER-SAW 2904-001498 SAF401 FILTER-SAW 2904-001499 SAF402 DUPLEXER-FBAR 2910-000009 SAF404 FILTER-SAW 2904-001474 SAF405 DUPLEXER-SAW 2910-000007 SAF500 FILTER-EMI/ESD 2901-001337 SAF501 FILTER-EMI/ESD 2901-001337 SAF502 FILTER-EMI/ESD 2901-001337 SAF503 FILTER-EMI/ESD 2901-001337 SAHEA50 HEADER-BOARD TO BOARD 3711-005550 SAHEA50 HEADER-BOARD TO BOARD 3711-005618 SAHEA50 HEADER-BOARD TO BOARD 3711-005728 SAJ3 CONNECTOR-FPC/FFC/PIC 3708-001880 SAJ4 SOCKET-BOARD TO BOARD 3710-002042 SAL100 BEAD-SMD 3301-001342 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-8
Design LOC Description SEC CODE STATUS
L101 BEAD-SMD 3301-001362 SAL103 BEAD-SMD 3301-001659 SAL200 INDUCTOR-SMD 2703-001786 SAL201 INDUCTOR-SMD 2703-002775 SAL202 INDUCTOR-SMD 2703-002775 SAL203 BEAD-SMD 3301-001342 SAL204 BEAD-SMD 3301-001120 SAL205 BEAD-SMD 3301-001120 SAL206 BEAD-SMD 3301-001729 SAL207 BEAD-SMD 3301-001120 SAL208 BEAD-SMD 3301-001120 SAL300 BEAD-SMD 3301-001342 SAL301 BEAD-SMD 3301-001729 SAL302 INDUCTOR-SMD 2703-001733 SAL303 INDUCTOR-SMD 2703-001990 SAL304 INDUCTOR-SMD 2703-001734 SAL305 INDUCTOR-SMD 2703-001734 SAL306 INDUCTOR-SMD 2703-001734 SAL307 INDUCTOR-SMD 2703-001749 SAL308 INDUCTOR-SMD 2703-001751 SAL309 INDUCTOR-SMD 2703-002208 SAL310 INDUCTOR-SMD 2703-001938 SAL311 INDUCTOR-SMD 2703-002198 SAL312 INDUCTOR-SMD 2703-002208 SAL313 INDUCTOR-SMD 2703-001724 SAL314 INDUCTOR-SMD 2703-002281 SAL316 BEAD-SMD 3301-001342 SAL319 BEAD-SMD 3301-001342 SAL321 INDUCTOR-SMD 2703-001748 SAL322 INDUCTOR-SMD 2703-001786 SAL323 INDUCTOR-SMD 2703-001734 SAL324 INDUCTOR-SMD 2703-001734 SAL400 INDUCTOR-SMD 2703-001749 SAL401 BEAD-SMD 3301-001120 SAL402 INDUCTOR-SMD 2703-002308 SAL403 INDUCTOR-SMD 2703-001751 SAL404 INDUCTOR-SMD 2703-001868 SAL405 INDUCTOR-SMD 2703-002833 SAL502 BEAD-SMD 3301-001342 SAL503 BEAD-SMD 3301-001342 SAL504 BEAD-SMD 3301-001342 SAL505 BEAD-SMD 3301-001342 SAL507 BEAD-SMD 3301-001342 SAL508 BEAD-SMD 3301-001342 SAL509 INDUCTOR-SMD 2703-002768 SAL510 INDUCTOR-SMD 2703-002768 SAOSC10 CRYSTAL-SMD 2801-004353 SAOSC10 RESONATOR-CERAMIC 2802-001182 SAOSC30 OSCILLATOR-VCO 2806-001348 SAOSC30 OSCILLATOR-VCTCXO 2809-001277 SA
SAMSUNG Proprietary-Contents may change without notice
Electrical Parts List
This Document can not be used without Samsung's authorization
10-9
Design LOC Description SEC CODE STATUS
OSC30 OSCILLATOR-VCTCXO 2809-001277 SAOSC50 OSCILLATOR-CLOCK 2804-001492 SAQ1 TR-DIGITAL 0504-001012 SAQ2 TR-DIGITAL 0504-001012 SAQ3 TR-DIGITAL 0504-001012 SAQ301 TR-DIGITAL 0504-001140 SAQ302 FET-SILICON 0505-001670 SAR100 R-CHIP 2007-001313 SAR105 R-CHIP 2007-000171 SAR106 R-CHIP 2007-000171 SAR107 R-CHIP 2007-000171 SAR109 R-CHIP 2007-000143 SAR110 R-CHIP 2007-000172 SAR111 R-CHIP 2007-000171 SAR113 R-CHIP 2007-000171 SAR120 R-CHIP 2007-000140 SAR121 R-CHIP 2007-000140 SAR124 R-CHIP 2007-000148 SAR125 R-CHIP 2007-000148 SAR126 R-CHIP 2007-000141 SAR128 R-CHIP 2007-000140 SAR130 R-CHIP 2007-001339 SAR132 R-CHIP 2007-000148 SAR134 R-CHIP 2007-000169 SAR135 R-CHIP 2007-000171 SAR136 R-CHIP