Download - CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

Transcript
Page 1: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

CADD SPECIFICATIONS

FOR AUTOCAD

CONSULTANTS’ MANUAL

Water Treatment & Solid Waste Facilities

Design & Construction, Major Infrastructure

Engineering & Construction Services

Page 2: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 1

RECORD OF REVISIONS

Date Section Page Details Name

Page 3: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 2

Table of Contents

1. General ......................................................................................................................................... 3

1.1 Introduction .......................................................................................................................................... 3 1.2 Objectives ............................................................................................................................................ 3 1.3 Content Provided with this Manual ...................................................................................................... 3 1.4 References .......................................................................................................................................... 3 1.5 Revisions ............................................................................................................................................. 4

2. Software ........................................................................................................................................ 5

2.1 AutoCAD .............................................................................................................................................. 5 2.2 PDF ...................................................................................................................................................... 5

3. File Management .......................................................................................................................... 5

3.1 CAD File Naming ................................................................................................................................. 5 3.2 Drawing and Sheet Numbers .............................................................................................................. 5

4. Standards ..................................................................................................................................... 6

4.1 Units ..................................................................................................................................................... 6 4.2 Scale .................................................................................................................................................... 6 4.3 Co-ordinates ........................................................................................................................................ 6 4.4 Templates ............................................................................................................................................ 6 4.5 Borders ................................................................................................................................................ 6 4.6 Layers .................................................................................................................................................. 7 4.7 Content Colour – Plotted Output ......................................................................................................... 8 4.8 Line Weight .......................................................................................................................................... 8 4.9 Screening ............................................................................................................................................. 8 4.10 Line Style ............................................................................................................................................. 9 4.11 Hatch Patterns ..................................................................................................................................... 9 4.12 Annotation ............................................................................................................................................ 9 4.13 Dimensions ........................................................................................................................................ 10 4.14 General Symbols ............................................................................................................................... 11 4.15 Discipline Specific Symbols ............................................................................................................... 11 4.16 Plotting ............................................................................................................................................... 11

5. Drawing Documentation ............................................................................................................ 13

5.1 Digital Submission Requirements ...................................................................................................... 13 5.2 Hardcopy Submission Requirements ................................................................................................ 13 5.3 As Built Submission Requirements ................................................................................................... 13

Appendices

Appendix A. Drawing Borders

Appendix B. Symbols

Page 4: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 3

1. General

1.1 Introduction

This document describes basic requirements and expectations related to the submission of AutoCAD

based drawing documentation for projects managed by Engineering & Construction Services.

It is intended to provide guidelines for the development of CADD drawing files utilized throughout all

phases of a project and to allow for effective archiving and future maintenance of the infrastructure

records.

1.2 Objectives

Maintain continuity across project deliverables

Common guidelines for drawing production

Basic requirements for electronic CAD deliverables

1.3 Content Provided with this Manual

AutoCAD Border Files

o _CoT-COV_863x603_2016.dwg

o _CoT-TTBL_863x603_2016.dwg

o _CoT-TTBL_CPPL_863x603_2016.dwg

o _CoT-TTBL_CPPL1_863x603_2016.dwg

o _CoT-TTBL_CPPR_863x603_2016.dwg

o _CoT-TTBL_CPPR1_863x603_2016.dwg

AutoCAD Border Attribute Files

o _CoT-TTBL-ATT_DWG.dwg

o _CoT-TTBL-ATT_REV.dwg

AutoCAD Drawing Template File

o _CoT-TEMPLATE_863x603_2016.dwt

AutoCAD General Symbol Block Files

o __CoT-PROJECT BLOCK FILE.dwg

o See Appendix A – General Symbol Legend

AutoCAD Plot Configuration Files

o _CADDS-PDF-SHT_DWG To PDF.pc3

o _CADDS-PDF-SHT_DWG To PDF.pmp

o _CADDS-PDF-SHT.ctb

1.4 References

National CAD Standard (NCS) www.nationalcadstandard.org

Construction Specifications Institute (CSI) www.csinet.org

National Institute of Building Sciences (NIBS) www.nibs.org

American Institute of Architects (AIA) www.aia.org

Page 5: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 4

1.5 Revisions

This document will be revised and reissued as required. Revision history is documented in the record of

revision table on page 1, please contact the City of Toronto’s Engineering and Construction Services

group to confirm current version;

Dimitar Dimitrov, P.Eng.

Engineer, Water Treatment & Solid Waste Facilities

Design & Construction, Major Infrastructure

Engineering & Construction Services

City of Toronto

310 Front Street

Suite 815

Toronto, Ontario M5V 3A4

P: 416.392.8214

F: 416.392.3300

E: [email protected]

Page 6: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 5

2. Software

2.1 AutoCAD

All contract documents utilizing this standard must be delivered in AutoCAD based software.

Electronic CAD deliverables shall be accepted in AutoCAD version 2013 or higher.

2.2 PDF

PDF plot configuration provided with this standard was based on Autodesk’s ‘DWG To PDF.pc3’ driver.

All PDF deliverables shall be viewable with Acrobat Reader XI.

3. File Management

3.1 CAD File Naming

The following file naming format shall be used for all project CAD file deliverables;

FFFF-YYYY-PP-NNN_DDDD.dwg

FFFF = Facility code – 3 or 4 character (alphanumeric) designation for each facility

YYYY = 4 digit year of project

PP = 2 digit City of Toronto project number

NNN = Sequential drawing number

DDDD = Discipline Sheet suffix (see section 3.2)

Example: 1001-2016-23-1_G001.dwg (Cover – Index)

1001-2016-23-2_A101.dwg (Architectural Plan)

3.2 Drawing and Sheet Numbers

The naming fragments noted above shall also be used for City of Toronto drawing numbers.

They are applied to the “DRAWING # “ attribute in the title block.

FFFF-YYYY-PP-NNN

Example: 1001-2016-23-1

1001-2016-23-2

Consultants shall develop d sheet numbers as required to effectively organize the drawing package. They

are applied to the “Discipline” attribute in the title block.

Page 7: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 6

The following discipline designators are recommended for use when developing discipline sheet numbers.

Additional designation and sheet numbering format should follow NCS-CSI uniform drawing system

guidelines.

G – General Example: G001 (Cover – Index)

C – Civil A101 (Architectural Plan)

A – Architectural

S – Structural

P – Process

M – Mechanical

E – Electrical

I – Instrumentation

4. Standards

4.1 Units

All drawing documentation is to be based on the Metric system. Drawings shall use a consistent unit of

measure unless noted otherwise.

4.2 Scale

Standard Metric Drawing Scales

1:5 1:100

1:10 1:200

1:20 1:500

1:50 1:1000

Please refer to NCS-CSI uniform drawing system guidelines for other common scales.

4.3 Co-ordinates

Geometry shall be Geo-Referenced to real world coordinates. The City of Toronto’s mapping is based on

3 degree MTM grid (Ontario Zone 10 – Modified Transverse Mercator). The files are coordinated on the

grid, which is derived from Horizontal Control Network, and in the range of (+/-) 4,800,000m (Northing) and

the y axis and (+/-) 300,000 (Easting) along the x axis.

4.4 Templates

An AutoCAD template file has been developed that incorporates all standards, content and configurations

outlined in this manual. This file should be used as a basis for all project drawings;

_CoT-TEMPLATE_863x603_2016.dwt

4.5 Borders

Standard borders are provided with this manual and are to be used with all drawing documentation. These

files are made up of the three main components listed below. When combined in a drawing file, this

arrangement allows for global editing of the border line work and title text, while maintaining individual

drawing revision and text attributes.

Page 8: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 7

Component 1: _CoT-TTBL_863x603_2016.dwg

This file contains border line work and text that is applicable across all project drawings. It is utilized as an

external reference file, loaded into paper space @ 0,0,0 on all drawing sheets.

The following layers have been set up to adjust border text to represent the City of Toronto’s various

engineering groups;

_CoT-TTBL-TDO_CWD - Solid Waste Management Services – Capital Works Delivery

_CoT-TTBL-TDO_ES - Solid Waste Management Services

_CoT-TTBL-TIM-CWD - Transportation Services – Capital Works Delivery

_CoT-TTBL-TIM-ES - Transportation Services

_CoT-TTBL-WIM-ES - Toronto Water - Water Infrastructure Management

_CoT-TTBL-WTS-ES - Toronto Water - Water Treatment Supply

_CoT-TTBL-WTS-OS - Toronto Water - Water Treatment Supply – Operational Support

_CoT-TTBL-WWT-ES - Toronto Water – Waste Water Treatment

_CoT-TTBL-WWT-OS - Toronto Water – Waste Water Treatment – Operational Support

Component 2: _CoT-TTBL-ATT_DWG.dwg

This file contains title block text attributes that are specific to individual drawings. It is inserted into paper

space @ 0,0,0 as a block.

Component 3: _CoT-TTBL-ATT_REV.dwg

This file contains the revision block text attributes specific to individual drawings. It is inserted into paper

space @ 0,0,0 as a block.

4.6 Layers

All drawing content shall be organized in a logical layering convention, following the AIA-NCS guidelines.

The following 5 Field naming format shall be utilized;

FIELD 1 FIELD 2 FIELD 3 FIELD 4 FIELD 5 A - W A L L - - - A D - W A L L - C - R O A D - M R K G - W H I T - N M - P I P E - D I G - S S - N

Field 1 – Required – Discipline Designator (See section 3.2) Field 2 – Required – Major Group (refer to AIA-NCS for typical groupings) Field 3 – Optional – Minor-1 Group (refer to AIA-NCS for typical groupings) Field 4 – Optional – Minor-2 Group (refer to AIA-NCS for typical groupings) Field 5 – Optional – Status (refer to AIA-NCS for typical groupings)

Note: The supplied ‘_CADDS-PDF-SHT.ctb’ configuration file utilizes object/layer line weight settings for

plotted output. Therefore, user defined layers must include line weight settings based on standard

thickness outlined in section 4.8

Page 9: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 8

4.7 Content Colour – Plotted Output

The supplied ‘_CADDS-PDF-SHT.ctb’ configuration file utilizes object/layer line weight setting for plotted

output. With this configuration colour is used for design visualization only, plotted line weights are not

determined by layer colour.

Note: Alternate user defined plot configurations are acceptable for use, however;

All settings must adhere to the standards outlined in this manual and shall function with the

supplied CAD content.

All custom plot configurations shall be used consistently across a project and supplied with

electronic deliverables.

4.8 Line Weight

The following standard line weights shall be used for all drawing deliverables;

LINE WEIGHT NAME PLOTTED LINE WIDTH mm

Extra Fine 0.13 mm

Fine 0.18 mm

Thin 0.25 mm

Medium 0.35 mm

Wide 0.50 mm

Extra Wide 0.70 mm

XX Wide 1.00 mm

XXX Wide 1.40 mm

XXXX Wide 2.00 mm

Please refer to NCS-CSI uniform drawing system guidelines.

4.9 Screening

The following screen levels shall be used on all drawing deliverables. They are based on a percentage of

black and are defined in the supplied ‘_CADDS-PDF-SHT.ctb’ configuration file.

Page 10: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 9

4.10 Line Style

The ‘ACADISO.lin’ set of generic Line Styles shall be used as default for all drawing deliverables.

Discipline specific styles may also be used as defined on their respective legend sheets.

Note: Custom line style configurations shall be supplied with electronic deliverables.

4.11 Hatch Patterns

Hatching shall be applied sparingly. Descriptions of hatch patterns used shall be clearly identified in

legends and applied consistently across the contract drawings.

Note: All custom hatch patterns shall be supplied with electronic deliverables.

4.12 Annotation

The following fonts and sizes shall be used for general drawing annotation. These styles are acceptable for

reduction by 50% when printing on small format printers.

TEXT EXAMPLE FONT SIZE

DRAWING TEXT ARIAL TTF 2.5mm

SUB-HEADING TEXT ARIAL TTF 3.5mm

HEADING TEXT ARIAL TTF 5.0mm

Page 11: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 10

AutoCAD text styles utilizing these settings are available in the provided template file;

_CoT-TEMPLATE_863x603_2016.dwt

Note: If custom text styles are required, utilize True Type Fonts and supply all custom configurations with

electronic deliverables.

4.13 Dimensions

All dimensioning shall utilize ARIAL True Type Font at a minimum 2.5mm. Arrowhead, Slash and Dot style

terminators are acceptable for use.

Dimension and leader styles utilizing these settings are available in the provided template file;

_CoT-TEMPLATE_863x603_2016.dwt

Page 12: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 11

4.14 General Symbols

The City of Toronto general symbols have been outlined in Appendix B. These symbols shall be used by

all disciplines, across the contract drawing set.

AutoCAD blocks for all general symbols are available in the provided template file;

_CoT-TEMPLATE_863x603_2016.dwt

4.15 Discipline Specific Symbols

The City of Toronto’s Process Control System (PCS) guidelines require the use of specific symbols for

Process and Instrumentation Diagrams. (see Appendix B)

The use of Standard Electrical symbols for control schematics, single line diagrams and electrical layouts

are also required. (see Appendix B)

(Please contact Toronto Water PCS group for more details.)

All other discipline specific symbols used in drawing production must be clearly identified on their

respective legend sheets and included in the drawing set.

4.16 Plotting

The standard format for drawing deliverables shall be full size PDF files. All full or reduced size hard copies

shall be produced from the delivered PDF files.

The following configuration files have been developed for production of full size PDFs from AutoCAD’s

paper space environment;

A. PaperSpace – _CADDS-PDF_863x603mm

This page set-up has been developed to utilize the configuration noted above, and is available in;

_CoT-TEMPLATE_863x603_2016.dwt

B. Plot Driver - _CADDS-PDF-SHT_DWG To PDF.pc3

Based on the standard AutoCAD ‘DWG To PDF’ driver.

C. Sheet Size - _CADDS-PDF-SHT_DWG To PDF.pmp

Engineering and Construction Services uses a modified ANSI-D size of 863mm x 603mm to

accommodate various printers/plotters available to the group. This custom sheet size has been

added to the plot configuration.

D. Plotted Line Weights - _CADDS-PDF-SHT.ctb

This .ctb file is structured to utilize AutoCAD object/layer line weight settings for final plotted

output. Object or Layer Colour will not determine plotted line weights.

Page 13: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 12

_CADDS-PDF_863x603mm

Note: Alternate user defined plot configurations are acceptable for use, however;

All settings must adhere to the standards outlined in this manual and shall function with the

supplied CAD content.

All custom plot configurations shall be used consistently across a project and supplied with

electronic deliverables.

AutoCAD plot outputs based on user defined configuration files must match the supplied PDF

drawing deliverables.

D A

B

C

Page 14: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 13

5. Drawing Documentation

5.1 Digital Submission Requirements

Refer to project contract and schedule for submission dates and requirements.

5.2 Hardcopy Submission Requirements

Refer to project contract and schedule for submission dates and requirements.

5.3 As Built Submission Requirements

Along with the final PDF drawing package, AutoCAD files shall be delivered for all As Built drawings.

Final CAD deliverables shall adhere to the guidelines set out in this manual and will conform to the

following requirements for submission;

CAD files will have all references bound into the drawing.

Required images and raster files will be named to align with the respective CAD drawing file and

shall load correctly in AutoCAD from the delivered electronic media.

The As Built stamp will be applied to all drawings.

(See Appnedix A. _CoT-BLK-GE32_AS BUILT.dwg )

The revision block will be cleared of all existing issuances and set to;

0 - DATE - AS BUILT - ‘Initials of Approver’

All custom configuration files used to develop drawing deliverables shall be provided with the

electronic deliverables.

AutoCAD plot outputs must match the supplied PDF drawing deliverables.

It is recommended that AutoCAD’s E-Transmit command be utilized to ensure all required content

and configurations are captured and supplied with the electronic deliverables.

Page 15: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 14

Appendix A

Drawing Borders

Contract Title Sheet

Standard Border

Plan and Profile Left 1

Plan and Profile Left 2

Plan and Profile Right 1

Plan and Profile Right 2

Page 16: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

PART MAIN FLOOR PLAN - SECTIONS AND DETAIL

DRAWING DESCRIPTION

1021-2016-01-6

CITY DWG No.ITEM

2

3

4

1

5

6

7

8

9

10

11

12

13

14

15

17

19

18

16

21

23

22

25

27

26

24

29

31

30

32

33

34

35

28

20

DRAWING INDEX

S203

DISCIPLINE

36

37

38

39

40

TITLE PAGE1021-2016-01-1 G001

LOCATION PLAN

DRAWINGNUMBER:

WASTEWATER TREATMENTWaterOPERATIONAL SUPPORT

OPERATIONAL SUPPORTDIRECTOR

RICHARD NOEHAMMER, P. ENG.GENERAL MANAGER

WASTEWATER TREATMENTDIRECTOR

LOU DI GIRONIMO

TORONTO WATER

FRANK QUARISA, P. ENG.

FACILITYPROJECT TITLECONTRACT NO.

DRAWING NO. G2

Page 17: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

CONTRACT No.DRAFTING:

SCALE:

DATE:

DESIGN: CHECK:

NUMBER:DRAWING

SIGNEDINITIALREVISIONSDATENo.

WASTE WATER TREATMENT

FRANK QUARISA, P. ENG.DIRECTOR, DIRECTOR,

RICHARD NOEHAMMER, P. ENG.

OPERATIONAL SUPPORT

WASTEWATER TREATMENTOPERATIONAL SUPPORT FACILITY

PROJECT TITLE

CONTRACT NO.

Water

Page 18: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

CONTRACT No.DRAFTING:

SCALE:

DATE:

DESIGN: CHECK:

NUMBER:DRAWING

SIGNEDINITIALREVISIONSDATENo.

WASTE WATER TREATMENT

FRANK QUARISA, P. ENG.DIRECTOR, DIRECTOR,

RICHARD NOEHAMMER, P. ENG.

OPERATIONAL SUPPORT

WASTEWATER TREATMENTOPERATIONAL SUPPORT FACILITY

PROJECT TITLE

CONTRACT NO.

Water

DATUM ELEV.

EXISTINGGROUND

ELEVATION

CENTRE LINEELEVATION

CHAINAGE

100.000

water\sewage\road

Page 19: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

CONTRACT No.DRAFTING:

SCALE:

DATE:

DESIGN: CHECK:

NUMBER:DRAWING

SIGNEDINITIALREVISIONSDATENo.

WASTE WATER TREATMENT

FRANK QUARISA, P. ENG.DIRECTOR, DIRECTOR,

RICHARD NOEHAMMER, P. ENG.

OPERATIONAL SUPPORT

WASTEWATER TREATMENTOPERATIONAL SUPPORT FACILITY

PROJECT TITLE

CONTRACT NO.

Water

CHAINAGE

CENTRE LINEELEVATION

ELEVATIONGROUNDEXISTING

DATUM ELEV.100.000

water\sewage\road

Page 20: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

CONTRACT No.DRAFTING:

SCALE:

DATE:

DESIGN: CHECK:

NUMBER:DRAWING

SIGNEDINITIALREVISIONSDATENo.

WASTE WATER TREATMENT

FRANK QUARISA, P. ENG.DIRECTOR, DIRECTOR,

RICHARD NOEHAMMER, P. ENG.

OPERATIONAL SUPPORT

WASTEWATER TREATMENTOPERATIONAL SUPPORT FACILITY

PROJECT TITLE

CONTRACT NO.

Water

DATUM ELEV.

CENTRE LINEELEVATION

CHAINAGE

ELEVATIONGROUNDEXISTING

100.000

water\sewage\road

Page 21: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

CONTRACT No.DRAFTING:

SCALE:

DATE:

DESIGN: CHECK:

NUMBER:DRAWING

SIGNEDINITIALREVISIONSDATENo.

WASTE WATER TREATMENT

FRANK QUARISA, P. ENG.DIRECTOR, DIRECTOR,

RICHARD NOEHAMMER, P. ENG.

OPERATIONAL SUPPORT

WASTEWATER TREATMENTOPERATIONAL SUPPORT FACILITY

PROJECT TITLE

CONTRACT NO.

Water

DATUM ELEV.

EXISTINGGROUND

ELEVATION

CENTRE LINEELEVATION

CHAINAGE

100.000

water\sewage\road

Page 22: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

2016-03_CITY OF TORONTO CADD SPEC FOR AUTOCAD.Docx 15

Appendix B

Symbols

General Symbols

Process and Instrumentation Diagram Symbols

Electrical Symbols

Page 23: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

SHEET TITLE

1001-2016-23-1 G0011:1000

2016-12-30

DESIGNED DRAWN CHECKED

DRAWING TYPE

AREA FOR

CONSULTANT LOGO

PROJECT ATTRIBUTES

COMPLETED IN THE BORDER REFERENCE FILE

SHEET ATTRIBUTES

COMPLETED IN DRAWING SHEET FILE

_CoT-TTBL-ATT_DWG.dwg

CITY OF TORONTO GROUP AND DIRECTORS

SET BY LAYERS IN THE BORDER REFERENCE FILE

SEE AUTOCAD SPEC MANUAL SECTION - 4.5 BORDERS

AS BUILT

AS BUILT STAMP

TYPICALLY LOCATE IN BOTTOM RIGHT CORNER

APPLY TO ALL AS BUILT SUBMISSIONS

_CoT-BLK-GE32_AS BUILT.dwg

ARE IN MILIMETERS UNLESS OTHERWISE NOTED

MEASUREMENTS SHOWN ON THESE PLANS

METRIC

METRIC STAMP

TYPICALLY LOCATE IN TOP LEFT CORNER

APPLY TO ALL DRAWING SUBMISSIONS

_CoT-BLK-GE11_METRIC NOTE mm.dwg

_CoT-BLK-GE12_METRIC NOTE m.dwg

REVISION BLOCK ATTRIBUTES

COMPLETED IN DRAWING SHEET FILE

_CoT-TTBL-ATT_REV.dwg

AREA FOR ENGINEERING SEALS

APPLY ORIGINAL SIGNED STAMP TO ALL

DWG VERSIONS OF SEALED DRAWINGS

_CoT-BLK-GE37_ORG SEALED BY.dwg

MAGNETIC NORTH

(FOR SITE PLANS ONLY)

_CoT-BLK-GE02_SITE TRUE NORTH.dwg

GENERAL SYMBOL LEGEND

SYMBOL DESCRIPTION

PROJECT NORTH

_CoT-BLK-GE04_PRJ NORTH.dwg

A

1

COLUMN GRID

_CoT-BLK-GE29_GRID.dwg

DWG #

ELEV

ELEVATION MARKER

_CoT-BLK-GE28_ELEV MARK REF.dwg

1 : 50

DWG #

AELEVATION

ELEVATION REFERENCE TITLE

_CoT-BLK-GE27_ELEV TITLE REF.dwg

DWG #

1

DETAIL CALLOUT

_CoT-BLK-GE39_DETAIL MARK REF.dwg

1 : 50

1

DETAIL

1 : 50 DWG #

1

DETAIL

DETAIL REFERENCE TITLE

_CoT-BLK-GE24_DETAIL TITLE.dwg

_CoT-BLK-GE26_DETAIL TITLE REF.dwg

LEVEL NAME

ELEVATION

ELEVATION DATUM

_CoT-BLK-GE41_ELEV DATUM.dwg

SECTION CALLOUTS

_CoT-BLK-GE16_SECTION MARK.dwg

_CoT-BLK-GE17_SECTION MARK REF.dwg

SYMBOL DESCRIPTION

SECTION REFERENCE TITLE

_CoT-BLK-GE36_SECTION TITLE.dwg

_CoT-BLK-GE23_SECTION TITLE REF.dwg

A

DWG #

A

DWG #

A 2016-12-30 ISSUED FOR 50% DETAIL DESIGN A.D.

A

DWG #

A

1:50

A

SECTION

1 : 50 DWG #

A

SECTION

1

REVISION TRIANGLE

_CoT-BLK-GE40_REV TRIANGLE.dwg

SECTION CALLOUTS

_CoT-BLK-GE19_SECTION MARK TAIL.dwg

_CoT-BLK-GE20_SECTION MARK REF TAIL.dwg

CADDS_ARIAL_2,5mm - DRAWING TEXT

CADDS_ARIAL_3.5mm - SUB HEADING TEXT

CADDS_ARIAL_5.0mm - HEADING TEXT

200

200

200

CADDS_LDR-A

CADDS_LDR-D

CADDS_DIM-S

CADDS_DIM-D

CADDS_DIM-A

A

A

ORIGINALLY SIGNED

AND SEALED BY;

DATED;

YYYY-MM-DD

P. ENG.

0.13mm - X FINE

0.13mm - X FINE - SCREENED

0.18mm - FINE

0.18mm - FINE - SCREENED

0.25mm - THIN

0.25mm - THIN - SCREENED

0.35mm - MEDIUM

0.35mm - MEDIUM - SCREENED

0.50mm - WIDE

0.50mm - WIDE - SCREENED

0.70mm - X WIDE

0.70mm - X WIDE - SCREENED

0.10mm - XX WIDE

0.10mm - XX WIDE - SCREENED

0.14mm - XXX WIDE

0.14mm - XXX WIDE - SCREENED

0.20mm - XXXX WIDE

0.20mm - XXXX WIDE - SCREENED

CONTRACT No.DRAFTING:

SCALE:

DATE:

DESIGN: CHECK:

NUMBER:DRAWING

SIGNEDINITIALREVISIONSDATENo.

WASTE WATER TREATMENT

FRANK QUARISA, P. ENG.DIRECTOR, DIRECTOR,

RICHARD NOEHAMMER, P. ENG.

OPERATIONAL SUPPORT

WASTEWATER TREATMENTOPERATIONAL SUPPORT FACILITY

PROJECT TITLE

CONTRACT NO.

Water

Page 24: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

THIS IS A CONTROLLED DOCUMENT - CONTACT TORONTO WATER PCS GROUP FOR CURRENT VERSION

Page 25: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

THIS IS A CONTROLLED DOCUMENT - CONTACT TORONTO WATER PCS GROUP FOR CURRENT VERSION

Page 26: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

THIS IS A CONTROLLED DOCUMENT - CONTACT TORONTO WATER PCS GROUP FOR CURRENT VERSION

Page 27: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

REVISIONS / CONTRACT NO.No. DATE INITIAL SIGNED

DRAFTING:

TORONTO WATEROPERATIONAL SUPPORT

DATE:

DESIGN:

SCALE: SHEET No.DRAWINGNUMBER:

CHECK: CONTRACT No.

DIRECTOR,OPERATIONAL SUPPORT

SCHEMATIC CONTROL SYMBOLS STANDARD LEGEND - ELECTRICAL (SHEET 1 OF3)ENTER FACILITY NAME

G13000-2014-01-1

STANDARD DRAWING

N.T.S

FEBRUARY, 2015

THIS IS A CONTROLLED DOCUMENT - CONTACT TORONTO WATER PCS GROUP FOR CURRENT VERSION

Page 28: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

REVISIONS / CONTRACT NO.No. DATE INITIAL SIGNED

DRAFTING:

TORONTO WATEROPERATIONAL SUPPORT

DATE:

DESIGN:

SCALE: SHEET No.DRAWINGNUMBER:

CHECK: CONTRACT No.

DIRECTOR,OPERATIONAL SUPPORT

SLD SYMBOLS & ABBREVIATIONSSTANDARD LEGEND - ELECTRICAL (SHEET 2 OF3)ENTER FACILITY NAME

G23000-2014-01-2

STANDARD DRAWING

N.T.S

FEBRUARY, 2015

STANDARD FUNCTION NUMBERS

THIS IS A CONTROLLED DOCUMENT - CONTACT TORONTO WATER PCS GROUP FOR CURRENT VERSION

Page 29: CADD SPECIFICATIONS FOR AUTOCAD CONSULTANTS MANUAL

REVISIONS / CONTRACT NO.No. DATE INITIAL SIGNED

DRAFTING:

TORONTO WATEROPERATIONAL SUPPORT

DATE:

DESIGN:

SCALE: SHEET No.DRAWINGNUMBER:

CHECK: CONTRACT No.

DIRECTOR,OPERATIONAL SUPPORT

LAYOUT SYMBOLS STANDARD LEGEND - ELECTRICAL (SHEET 3 OF3)ENTER FACILITY NAME

G33000-2014-01-3

STANDARD DRAWING

N.T.S

FEBRUARY, 2015

THIS IS A CONTROLLED DOCUMENT - CONTACT TORONTO WATER PCS GROUP FOR CURRENT VERSION