1800 328 200 | www.legend.com.au | [email protected]
Cable Laying & Equipment
ContentsContents
Pulling Tools 3
Conduit Rods and Frames 7
Gas Tools 8
Drum Stands 13
Cable Rollers 15
Conduit Cable Guides 16
Cable Lubricant 19
Hauling Rope 20
Cable Blowers 20
Line Carriers 21
Cleaners and Mandrels 22
Hauling Swivels 23
Line Tensioners 27
Cable Stocking 28
Cable Pullers 32
Manhole Equipment 33
Pit Keys and Breaker 34
Index 36
GENERAL LINE EQUIPMENT
3
MSP Conduit Rod KitsThe MSS range of fibreglass rods have a copper trace wire running through the core making them suitable for underground cable & conduit locating, with the use of a suitable locator. The rod is supplied complete with brass male ends & hauling eye, and fitted to a sturdy zinc plated steel frame with brake. Optional re-fills are available as well as flex ends and joining kits.
4.5mm 6mm 9mm 11mm
• Highly flexible wire springs with a steel wire reinforcement through the middle• Ideal for ‘fishing’ in conduits and ducting• For smaller direct pulls or attach a pull line in larger pulls
CABAC PULL THROUGH SPRINGS
Part No. Min. Breaking Strain (kg) Length (mm) Unit Qty
PTS20M 100 20 EA 1
PTS30M 100 30 EA 1
PULLING TOOLS
Part No. P802163 • Triple stranded cable pulling device• Non-conducting coiled spring leader• Material: Polyester Wire• Available in 30m and 60m lengths
CROMASNAKE FIBREGLASS CABLE SNAKE 30MCROMA CABLE SNAKES
Unit: EA Qty: 1
Part No. P802164 • Triple stranded cable pulling device• Non-conducting coiled spring leader• Material: Polyester Wire• Available in 30m and 60m lengths
CROMASNAKE FIBREGLASS 5MMCABLE SNAKE 60M Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
4
Part No. FTCM30 • Top end professional fish tape made from pull-truded glass with special polypropylene outer coating - low friction and high abrasion
resistance• Non-conductive glass increases safety• Resilient to bending and shear stresses• Can be repaired if broken using repair kit (Part No. FTRC)
CABLEMASTER - FIBREGLASS FISH TAPE 30MCABAC FISH TAPES
Unit: EA Qty: 1
Part No. FTGJ20 • Top end professional fish tape made from pull-truded glass with special polypropylene outer coating - low friction and high abrasion
resistance• Non-conductive glass increases safety• Highly resilient to bending and shear stresses• Supplied in a tubular casing with a shoulder strap
GLASSJACK - FIBREGLASS FISH TAPE 20M Unit: EA Qty: 1
Part No. FTR6 • Set of flexible cable pulling rods which connect together to form a pulling rod up to 6m in length• Suitable for installing wiring and light cables into a roof• Supplied in a sturdy transparent plastic packing tube• Rods from another set may be added to make an even longer pulling
CABLEPR PUSH PULL CABLE ROD SET Unit: EA Qty: 1
Part No. FTRC • Suitable for use with CABLEMASTER fish tape• Accessories include PULLGRIP cable stocking and FLEXIGRIP• Repair items include rod ends, splices and special adhesive
FISH TAPE ACCESSORIES AND REPAIR KITCABAC FISH TAPE REPAIR KITS
Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
5
Part No. MSS-GCG30V • Fitted to a sturdy plastic wheel suitable for both left and right handed users• Supplied with various end attachments• Rod repair kit stored neatly in the centre of the dispenser• Comes with 1 x lubrication spray bottle
MINI ROD - 3MM X 30MTR Unit: EA Qty: 1
Part No. MSS-THR-223M • A lighter, stronger and more flexible hand rod• Made from Polycarbonate• Fitted with brass ends• Supplied in 22mm x 3m lengths
WHITE HAND ROD-3MTR X 22MM Unit: EA Qty: 1
Part No. MSS-TCH-22MF • Connects on to the end of a 22mm hand rod to assist twisting the rod in a clockwise direction
CRANK HANDLE FOR 22MM HAND RODS Unit: EA Qty: 1
Part No. MSS-TFL-22 • Suits a 22mm hand rod
FLEXIBLE LEADER FOR 22MM HAND RODS Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
6
Part No. MSS-THL-2290 • For linking hand rod in conduit• Suits a 22mm hand rod
HOOK & LOOP SET TO SUIT 22MM HAND RODS Unit: EA Qty: 1
Part No. MSS-TRE-22 • Suits a 22mm hand rod
LEAD IN EYE FOR 22MM HAND RODS Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
7
• Flexible spring leader to suit a 4.5mm rod• 6, 9 & 11mm rod flexible springs leaders also available
MSP CONDUIT KIT FITTINGS
Part No. Description Unit Qty
MSS-4.5FLEX FLEXY END FITTING - 4.5MM ROD EA 1
MSS-6FLEX FLEXY END - 6MM O/D ROD EA 1
MSS-9FLEX FLEXY END FITTING - 9MM ROD EA 1
MSS-11FLEX FLEXY END FITTING - 11MM ROD EA 1
CONDUIT RODS AND FRAMES
• Suitable for underground cables and conduit locating with the use of a suitable locator• Supplied complete with brass ends and hauling eye• Copper trace wire running through the core• Fitted to a sturdy zinc plated steel frame with brake
MSP CONDUIT ROD KITS
Part No. Description Unit Qty
MSS-4.5-30 4.5MM X 30 MTR TRACE ROD AND FRAME KIT 1
MSS-4.5-60 4.5MM X 60MTR TRACE ROD AND FRAME KIT 1
MSS-4.5-80 4.5MM X 80MTR TRACE ROD AND FRAME KIT 1
MSS-4.5-100 4.5MM X 100MTR TRACE ROD AND FRAME KIT 1
MSS-6TR-60 6MM X 60MTR TRACEROD AND FRAME KIT 1
MSS-6TR-80 6MM X 80MTR TRACEROD AND FRAME KIT 1
MSS-6TR-100 6MM X 100MTR TRACEROD AND FRAME KIT 1
MSS-6TR-120 6MM X 120MTR TRACEROD AND FRAME KIT 1
MSS-6TR-150 6MM X 150MTR TRACEROD AND FRAME EA 1
MSS-6TR-200 6MM X 200MTR TRACEROD AND FRAME EA 1
MSS-9TR-100 9MM X 100MTR TRACEROD AND FRAME KIT 1
MSS-9TR-125 9MM X 125MTR TRACEROD AND FRAME KIT 1
MSS-9TR-150 9MM X 150MTR TRACEROD AND FRAME KIT 1
MSS-9TR-200 9MM X 200MTR TRACEROD AND FRAME KIT 1
MSS-9TR-250 9MM X 250MTR TRACE ROD AND FRAME KIT 1
MSS-11TR-125 11MM X 125MTR TRACEROD AND FRAME KIT 1
MSS-11TR-150 11MM X 150MTR TRACEROD AND FRAME KIT 1
MSS-11TR-200 11MM X 200MTR TRACEROD AND FRAME KIT 1
MSS-11TR-250 11MM X 250MTR TRACEROD AND FRAME KIT 1
MSS-11TR-300 11MM X 300MTR TRACEROD AND FRAME KIT 1
MSS-11TR-350 11MM X 350MTR TRACEROD AND FRAME KIT 1
MSS-11TR-400 11MM X 400MTR TRACEROD AND FRAME KIT 1
GENERAL LINE EQUIPMENT
8
• Suitable for underground cables and conduit locating with the use of a suitable locator• Refill for rod and frame• Copper trace wire running through the core• Various lengths and diametres available• Comes with brass frame attachment & hauling eye
MSP REFILL COILS
Part No. Description Unit Qty
MSS-RFL-4.5-30 REFILL COIL - 4.5MM TRACE ROD X 30MTR EA 1
MSS-RFL-4.5-60 REFILL COIL - 4.5MM TRACE ROD X 60MTR KIT 1
MSS-RFL-4.5-80 REFILL COIL - 4.5MM TRACE ROD X 80MTR KIT 1
MSS-RFL-6-60TR REFILL COIL - 6MM TRACE ROD X 60MTR EA 1
MSS-RFL-6-80TR REFILL COIL - 6MM TRACE ROD X 80MTR KIT 1
MSS-RFL-6-100TR REFILL COIL - 6MM TRACE ROD X 100MTR KIT 1
MSS-RFL-6-120TR REFILL COIL - 6MM TRACE ROD X 120MTR KIT 1
MSS-RFL-6-150TR REFILL COIL - 6MM TRACE ROD X 150MTR EA 1
MSS-RFL-9-100TR REFILL COIL - 9MM TRACE ROD X 100MTR EA 1
MSS-RFL-9-125TR REFILL COIL - 9MM TRACE ROD X 125MTR EA 1
MSS-RFL-9-150TR REFILL COIL - 9MM TRACE ROD X 150MTR KIT 1
MSS-RFL-9-200TR REFILL COIL - 9MM TRACE ROD X 200MTR KIT 1
MSS-RFL-9-250TR REFILL COIL - 9MM TRACE ROD X 250MTR EA 1
MSS-RFL-11-125TR REFILL COIL - 11MM TRACE ROD X 125MTR EA 1
MSS-RFL-11-150TR REFILL COIL - 11MM TRACE ROD X 150MTR EA 1
MSS-RFL-11-200TR REFILL COIL - 11MM TRACE ROD X 200MTR EA 1
MSS-RFL-11-250TR REFILL COIL - 11MM TRACE ROD X 250MTR EA 1
MSS-RFL-11-300TR REFILL COIL - 11MM TRACE ROD X 300MTR EA 1
MSS-RFL-11-350TR REFILL COIL - 11MM TRACE ROD X 350MTR EA 1
MSS-RFL-11-400TR REFILL COIL - 11MM TRACE ROD X 400MTR EA 1
• Repair/joining kit for our range of MSS Power conduit rods• Includes rod joiners, male ends, hauling eyes and glue packs
MSP REPAIR KITS
Part No. Description Unit Qty
MSS-JK4.5-3.0 JOINING KIT FOR 4.5MM OD TRACE ROD EA 1
MSS-JK6.5-4.5 JOINING KIT FOR 6MM OD TRACE ROD EA 1
MSS-JK6.0-8.0 JOINING KIT FOR 9MM OD TRACE ROD EA 1
MSS-JK10.0-8.0 JOINING KIT FOR 11MM OD TRACE ROD EA 1
Part No. MSS-TEL414-82 • 3/8 BSP Ends to Suit other Gas Accessories• Accurate and Quick Flame Setting
GAS HAND PIECEMSP GAS TOOLS
GAS TOOLS
Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
9
Part No. MSS-TEL414-130 • 3/8 BSP Ends to Suit other Gas Accessories• Strong windproof flame
SOFT FLAME BURNER Unit: EA Qty: 1
Part No. MSS-TEL414-77 • 3/8 BSP Ends to Suit Other Gas Accessories
HARD FLAME BURNER Unit: EA Qty: 1
Part No. MSS-TEL414-84 • 3/8BSP ends to suit other gas accessories• Regulator has leak test and hose failure system
LEAK TEST REGULATOR Unit: EA Qty: 1
Part No. MSS-TEL414-105 • 3/8 BSP Ends to Suit Other Gas Accessories• 6m• 2m hose set available p/n MSS-TEL414-71
6MTR HOSE SET GAS Unit: EA Qty: 1
Part No. MSS-TEL414-50 • Telstra Approved gas cylinder• 3/8BSP ends to suit other gas accessories• 1.25kg slimline refillable cylinder• 3kg and 9kg gas cylinders available
1.25KG GAS CYLINDER Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
10
Part No. MSS-SV3366 • Automatic ignition - guaranteed for 30,000 ignitions• Trigger on/off function - no waste of LP gas• Precise flame adjustment valve• Ergonomic and modern design
HANDLE BLOW TORCH PROMATIC 3366 Unit: EA Qty: 1
Part No. MSS-TX405C • Creates spark to ignite gas burners• Supplied with 2x replacement flints• Ignites most propane and MAPP gas fuelled appliances
CUP STYLE FLINT LIGHTER Unit: EA Qty: 1
Part No. MSS-306311 • Suits 9kg gas cylinder
GAS REG W/HOSE FAIL VALVE POL CONN. Unit: EA Qty: 1
Part No. MSS-100505001 • Used in busy communication pits to protect neighbouring cable whilst heatshrinking• Small and flexible• Made from flame retardant material
JOINTERS HEATSHIELD - 30 X 30CM Unit: EA Qty: 1
GENERAL LINE EQUIPMENT
11
Part No. 45-235 • Self-adjusting stripping blades automatically select proper position• Strips 12 AWG solid to 14 AWG Underground Feeder (UF) Cable• Strips twin and earth cable• Neatly removes outer cable sheath and then inner wire sheathing• Strips twin and earth cable
IDEAL UNDERGROUND FEEDER CABLE STRIPPERIDEAL GAS TOOLS
Unit: EA Qty: 1
• 60/40 Resin Cored High Quality Solder 500g• Tin/Lead, Low Melting Point Solder• Conforms BSS 441 DTD 599A• Max 0.5% Halide
ECCO GAS TOOLS
Part No. Description Unit Qty
P611007 0.56 MM 60/40 SOLDER 500G REEL EA 1
P611005 0.71MM 60/40 SOLDER 500G 20SWG EA 1
P611003 0.91MM 60/40 SOLDER 500G REEL EA 1
P611001 1.6MM 60/40 SOLDER 500G REEL EA 1
P611002 1.21MM 60/40 SOLDER 500G REEL EA 1
P611004 2.3MM 60/40 SOLDER 500G REEL EA 1
P611009 3.2MM SOLDER 60/40 500G REEL EA 1
UNDERGROUND CABLE HANDLING
12
Scissor Type Cable Drum JacksThe Scissor lift drum stands are well suited for uneven ground as the individual lifting screws can be adjusted separately.
They are simple and easy to use and utilise sealed directional bearings (insert) for ease of lifting and lowering of cable drums.
Complete with two stands with wheels for transportation, collars to retain drums and a ground joining bar for rigidity during operation. Along with a stamped and registered load bearing axle, the SLS is a very cost effective and efficient set of equipment.
Features:• Made in Australia• Manoeuvrable and Transportable• Designed for Rugged Use• Winding via Spin Handle or with a 25mm Ratchet
Wrench• Fitted with Wheels for Ease of Placement• Suitable for Lifting Cable Drums up to 4 tonneALSO AVAILABLE:Part No. MSS-SLS1-2TScissor Drum Jack Set - Suitable for lifting cabledrums up to 2 tonne.
Directional Bearings
SUITABLEFOR CABLE
DRUMSUP TO
4 TONNE
Optional Accessories:Part No. MSS-DB-400 Disc brake and fixing arm set to suit 40mm dia axle
Part No. MSS-DB-630 Disc brake and fixing arm set to suit 63mm dia axle
Part No. MSS-DB-660 Disc brake and fixing arm set to suit 66mm dia axle
Part No. MSS-DB-900 Disc brake and fixing arm set to suit 90mm dia axle
Hydraulic Cable Drum JacksCable drum jacks are used for holding or lifting cable drums off the ground so they can be uncoiled for installation of underground power cables, conductors, wire, coaxial cable, etc. The cable drum is moved, rolled or lifted into position and then jacked up using an integrated hydraulic jack or screw jack system.
Optional accessories available are a disc brake and a fixing arm. These two items have been specially designed to complement the Hydraulic Cable Drum Jack to deliver further versatility and usability.
Image shows optional Disc brake feature.
SUITABLEFOR CABLE
DRUMSUP TO
8 TONNE
Manoeuverable and Transportable
Part No. MSS-DJS-58T
Part No. MSS-SLS3-4T
UNDERGROUND CABLE HANDLING
13
Part No. MSS-CRS350 • Quality construction cable reel dispenser• Suits 2 to 3 reels of electrical cable• Maximum 650mm OD drum
CABLE REEL STAND - MAX 650MM OD DRUMMSP DRUM STANDS
DRUM STANDS
Unit: EA Qty: 1
Part No. MSS-CDT-500 • Quality construction cable drum trolley• Suits a 90cm wide x 1m diameter drum• Holds drum up to 500kg
CABLE DRUM TROLLEY TO SUIT UPTO 500KG Unit: EA Qty: 1
Part No. MSS-SLS-05T • Suitable for lifting cable drums up to 500kg’s• Fully collapsible for easy transportation• Set up in minutes
SCISSOR DRUM JACK SET-UP TO 500KG Unit: EA Qty: 1
Part No. MSS-SLS1-2T • Suitable for lifting cable drums up to 2 tonne• Fully collapsible for easy transportation• Set up in minutes• Comes with a 60mm OD axle• Comes with 2 x drum retaining collars
SCISSOR DRUM JACK SET - UP TO 2 TON Unit: EA Qty: 1
Part No. MSS-SLS3-4T • Suitable for lifting cable drums up to 4 tonne• Fully collapsible for easy transportation• Set up in minutes• Comes with a 90mm OD axle• Comes with 2 x drum retaining collars
SCISSOR DRUM JACK SET - UP TO 4 TON Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
14
Part No. MSS-DJS-58T • Works with the use of bottle jacks fitted to the base to lift the drum off the ground• Suitable for drums up to 8 tonne• Optional disc brake feature
HYDRAULIC DRUM JACK SET 8T WWL MAX Unit: EA Qty: 1
Part No. MSS-DRR-1000 • For use with drum diameters up to 1.5m• Safe Work Load of 1000kg (per set)• Fold away for easy storage
DRUM RAMP ROLLER SET 1000KG Unit: EA Qty: 1
Part No. MSS-4JZ-DZ255S • 1000kg drum capacity• 400-1200mm drum OD capacity• Heavy Duty• Comes with Joiner Bar
DRUM RAMP ROLLERS-1T-40-1120CM Unit: EA Qty: 1
• Accessory for the MSS-DJS-58T Hydraulic Cable Drum Jack• Suits 40mm diameter axle• Other sizes also available
DISC BRAKE AND FIXING ARMS
Part No. Description Unit Qty
MSS-DB-400 DISC BRAKE & FIXING ARM SUITS 40MM AXLE EA 1
MSS-DB-630 DISC BRAKE & FIXING ARM SUITS 63MM AXLE EA 1
MSS-DB-660 DISC BRAKE/FIXING ARM- SUIT 66MM OD AXLE EA 1
MSS-DB-900 DISC BRAKE & FIXING ARM SUITS 90MM AXLE EA 1
UNDERGROUND CABLE HANDLING
15
Part No. MSS-NTR-120 • Economy trench roller with flat base - 120mm wide plastic roller• Single plastic roller• Zinc plated frame• 500kg WLL
FLAT TRENCH ROLLER - PLASTIC ROLLERMSP CABLE ROLLERS
CABLE ROLLERS
Unit: EA Qty: 1
Part No. MSS-NTRA-120 • Trench roller with flat base - 120mm wide aluminium roller• Single Aluminium roller• Zinc plated frame• 1000kg WLL
FLAT TRENCH ROLLER - ALUMINIUM ROLLER Unit: EA Qty: 1
Part No. MSS-RTR-140 • Economy raised trench roller - 140mm wide plastic roller• Single plastic roller• Zinc plated frame• 500kg WLL
RAISED TRENCH ROLLER - 140MM PLASTIC Unit: EA Qty: 1
Part No. MSS-RTRA-140 • Raised trench roller raised -140mm wide aluminium roller• Single Aluminium roller• Zinc plated frame• 1000kg WLL
RAISED TRENCH ROLLER - 140MM Unit: EA Qty: 1
Part No. MSS-TCR-200 • Trench corner roller, used to create a 90 degree bend• optional star picket available p/n MSS-SCR-600
TRENCH CORNER ROLLER Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
16
Part No. MSS-TRGM-100 • Above ground to conduit transition cable guide - 125mm OD cable max• Single Aluminium roller• Zinc plated frame
MANHOLE GUIDE - SINGLE ROLLER Unit: EA Qty: 1
Part No. MSS-TRGM-100-2 • Above ground to conduit transition cable guide - 125mm OD cable max• Two Aluminium rollers• Zinc plated frame
MANHOLE GUIDE - TWIN ROLLER Unit: EA Qty: 1
Part No. MSS-TRGM-100-3 • Above ground to conduit transition cable guide - 125mm OD cable max• Three Aluminium rollers• Zinc plated frame
MANHOLE GUIDE - TRIPLE ROLLER Unit: EA Qty: 1
• Chrone Zinc Plated Finish• Uses a ‘bell mouth’ to aid the entering and exit of cables• Lockable inside conduit
MSP INLINE FEEDING SHEAVES
Part No. Description Unit Qty
MSS-IFS-080 INLINE FEEDING SHEAVE FOR 80MM CONDUIT EA 1
MSS-IFS-100 INLINE FEEDING SHEAVE 100MM CONDUIT EA 1
MSS-IFS-125 INLINE FEEDING SHEAVE 125MM CONDUIT EA 1
MSS-IFS-150 INLINE FEEDING SHEAVE FOR 150MM CONDUIT EA 1
CONDUIT CABLE GUIDES
UNDERGROUND CABLE HANDLING
17
• Provides a smooth surface for the cable to glide easily against• Various sizes available - up to 150mm
MSP CONDUIT SLIPPER GUIDE
Part No. Description Unit Qty
MSS-CCG-028 CONDUIT SLIPPER GUIDE 28MM EA 1
MSS-CCG-035 CONDUIT SLIPPER GUIDE 35MM EA 1
MSS-CCG-050 CONDUIT SLIPPER GUIDE 50MM EA 1
MSS-CCG-080 CONDUIT SLIPPER GUIDE 80MM EA 1
MSS-CCG-100 CONDUIT SLIPPER GUIDE 100MM EA 1
MSS-CCG-125 CONDUIT SLIPPER GUIDE 125MM EA 1
MSS-CCG-150 CONDUIT SLIPPER GUIDE 150MM EA 1
• Locks to the inside of the conduit to provide a smooth, stable surface for cable to glide easily• Various sizes available
MSP LOCKABLE CABLE SLIPPER GUIDES
Part No. Description Unit Qty
MSS-CLS-050 LOCKABLE CONDUIT SLIPPER GUIDE 50MM EA 1
MSS-CLS-080 LOCKABLE CONDUIT SLIPPER GUIDE 80MM EA 1
MSS-CLS-100 LOCKABLE CONDUIT SLIPPER GUIDE 100MM EA 1
MSS-CLS-125 LOCKABLE CONDUIT GUIDE 125MM EA 1
MSS-CLS-150 LOCKABLE CONDUIT GUIDE 150MM EA 1
• Suitable for use in electrical and telecommunication conduit• Cast Aluminium bell mouth guides assist in protecting cable• Various sizes available
MSP BELLMOUTH CABLE GUIDES
Part No. Description Unit Qty
MSS-BM100 BELLMOUTH CONDUIT GUIDE - 100MM EA 1
MSS-BM125 BELLMOUTH CONDUIT GUIDE - 125MM EA 1
MSS-BM150 BELLMOUTH CONDUIT GUIDE - 150MM EA 1
Part No. MSS-PMCG-100 • Above ground to conduit transition cable guide - 100mm OD cable max• Pivoting slipper guide for cable protection• Zinc plated
PIVOTING GUIDE 100MMMSP PIVOT GUIDES
Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
18
Part No. MSS-PMRG-140 • 3x 140mm rollers• Pivoting guide with 3 rollers for protection of large UG cable• Aluminium rollers - zinc plated frame
PIVOTING GUIDE WITH 3 X 140 ROLLERS Unit: EA Qty: 1
Part No. MSS-FS-050 • To suit 50mm Telstra conduit• Min 46mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish
LOCKABLE ROLLER GUIDE 50MMMSP LOCKABLE CONDUIT ROLLER GUIDES
Unit: EA Qty: 1
Part No. MSS-FS-063 • To suit 63mm conduit• Min 48mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish
LOCKABLE ROLLER GUIDE 63MM Unit: EA Qty: 1
Part No. MSS-FS-080 • To suit 80mm conduit• Min 70mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish
LOCKABLE ROLLER GUIDE 80MM Unit: EA Qty: 1
Part No. MSS-FS-100 • To suit 100mm conduit• Min 95mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish
LOCKABLE ROLLER GUIDE 100MM Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
19
Part No. MSS-FS-125 • To suit 125mm conduit• Min 120mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish
LOCKABLE ROLLER GUIDE 125MM Unit: EA Qty: 1
Part No. MSS-FS-150 • To suit 150mm conduit• Min 140mm adjustable split lock OD• Full ball bearing roller guide• Chrome zinc plated finish
LOCKABLE ROLLER GUIDE 150MM Unit: EA Qty: 1
Part No. MSS-LN1478 • Water based cable blowing lubricant specifically designed for lubricating sub-duct prior to high speed fibre optic cable blowing• Compatible with all forms of cable jacket• Does not stress crack Polyethylene plastics• 20LTR Drum
DUCTGLIDE CABLE BLOWING LUBE 20LTR Unit: EA Qty: 1
• Water based cable hauling lubricant for excellent friction reduction - non-toxic and non-flammable• For hauling heavy power, telecommunication and fibre optic cable• Compatible with all forms of cable jacket• 20LTR Drum
MSP CABLE LUBRICANT
Part No. Description Unit Qty
MSS-LN1477 POWERGEL CABLE HAULING LUBE 20LTR EA 1
MSS-LN1477-4 POWERGEL - 4LTR PALE EA 1
CABLE LUBRICANT
UNDERGROUND CABLE HANDLING
20
Part No. MSS-LPPHTA12 • Hauling rope with a break load of 2700kg• Material: Polypropylene• 250m coil
POLY PROP ROPE 12MM X 250MTRMSP HAULING ROPE
HAULING ROPE
Unit: EA Qty: 1
Part No. MSS-LPPHTG16 • Hauling rope with a break load of 4500kg• Material: Polypropylene• 250m coil
POLY PROP ROPE 16MM X 250MTR Unit: EA Qty: 1
Part No. MSS-LPPHTA20 • Hauling rope with a break load of 6900kg• Material: Polypropylene• 250m coil
POLY PROP ROPE 20MM X 250MTR Unit: EA Qty: 1
Part No. MSS-C-1250-0001-01 • Capable of installing fibre optic cable (6-32mm O.D. ) at speeds up to 90m per minute into pre installed sub-duct (25-63mm)• Electronic monitoring system provides read out of speed/distance• Electronic pressure sensor shuts off machine for obstructions• Collets and seals are required for cables and sub-duct• Includes portable petrol engine driven hydraulic pump and hoses
TORNADO CABLE BLOWING MACHINEMSP CABLE BLOWERS
CABLE BLOWERS
Unit: EA Qty: 1
Part No. MSS-C-1254-001-01 • Designed to install new a cable into an occupied sub-duct (subject to space)• Heavy-duty Aluminium base and lid• Collets and seals are required for cables and sub-duct
JUNCTION BOX FOR OVERBLOWING Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
21
Part No. MSS-EBK2-1300K • Effective in blowing a light-weight jet line up to 1000m of unoccupied conduit• Each motor (x 2 off) delivers approx. 3.5m3 of air per minute• Incl 3 x rope grommets for 3mm, 5mm and 5mm draw line• Incl 3x conduit sealoffs to suit 12mm up to 160mm conduit• Replacement blower ‘ONLY’ available p/n MSS-EBK2-1300
ELECTRIC JETLINE BLOWER KIT Unit: EA Qty: 1
Part No. MSS-DPL-500 • Used in conjunction with an air compressor• Suitable for conduits 50-150mm• Can accommodate rope 4-10mm• Complete kit supplied with carry case• 40mm conduit seal off available
CONDUIT ROPING KIT Unit: EA Qty: 1
• Shaped like a balloon with a rigid plastic mouth to ensure that the balloon stays inflated• Various sizes available
MSP LINE CARRIERS
Part No. Description Unit Qty
MSS-DBL-035 BALLOON LINE CARRIER - 35MM EA 1
MSS-DBL-063 BALLOON LINE CARRIER - 63MM EA 1
MSS-DBL-050 BALLOON LINE CARRIER - 50MM EA 1
MSS-DBL-080 BALLOON LINE CARRIER - 80MM EA 1
MSS-DBL-100 BALLOON LINE CARRIER - 100MM EA 1
MSS-DBL-125 BALLOON LINE CARRIER - 125MM EA 1
MSS-DBL-150 BALLOON LINE CARRIER - 150MM EA 1
MSS-DBL-190 BALLOON LINE CARRIER - 190MM EA 1
MSS-DBL-225 BALLOON LINE CARRIER - 225MM EA 1
LINE CARRIERS
UNDERGROUND CABLE HANDLING
22
• Ideal for internal cleaning of ducts and conduits of debris• Galvanised finish• Made with 22g wire strand
MSP WIRE BRUSH CONDUIT CLEANERS
Part No. Description Unit Qty
MSS-WBC-050 WIRE BRUSH MANDREL - 50MM EA 1
MSS-WBC-080 WIRE BRUSH MANDREL - 80MM EA 1
MSS-WBC-100 WIRE BRUSH MANDREL - PROVING / CLEANING EA 1
MSS-WBC-125 WIRE BRUSH MANDREL - PROVING / CLEANING EA 1
MSS-WBC-150 WIRE BRUSH CLEANER 22G WIRE FOR 150MM EA 1
MSS-WBC-200 WIRE BRUSH CLEANER 22G WIRE FOR 200MM EA 1
CLEANERS AND MANDRELS
• Suitable for clearing the conduit of sand, mud and other debris
MSSP CONDUIT CLEANERS
Part No. Description Unit Qty
MSS-CRC-050 RUBBER CONDUIT CLEANER - 53MMOD CRC-050T EA 1
MSS-CRC-080 RUBBER CONDUIT CLEANER - 80MM EA 1
MSS-CRC-100 RUBBER CONDUIT CLEANER - 100MM EA 1
MSS-CRC-125 RUBBER CONDUIT CLEANER - 125MM EA 1
MSS-CRC-150 RUBBER CONDUIT CLEANER - 150MM EA 1
Used for testing conduit integrity before hauling cableTest electrical communications conduits
MSP DUCT PROVING MANDRELS
Part No. Description Unit Qty
MSS-DPM-010 PROVING MANDREL 10MM O/D EA 1
MSS-DPM-014 PROVING MANDREL 14MM O/D EA 1
MSS-DPM-015 PROVING MANDREL 15MM O/D EA 1
MSS-DPM-018 PROVING MANDREL 18MM O/D EA 1
MSS-DPM-020 PROVING MANDREL 20MM O/D EA 1
MSS-DPM-022 PROVING MANDREL 22MM O/D EA 1
MSS-DPM-030 DUCT PROVING MANDREL 28MM O/D EA 1
MSS-DPM-050 PROVING MANDREL 47MM OD EA 1
MSS-DPM-080 PROVING MANDREL 74MM OD EA 1
MSS-DPM-100 PROVING MANDREL 90MM O/D EA 1
MSS-DPM-125 PROVING MANDREL 115MM OD EA 1
MSS-DPM-150 PROVING MANDREL 150MM -OD 130MM EA 1
UNDERGROUND CABLE HANDLING
23
• Used for spreading lubricant especially on tight radius corners• Suitable for clearing the conduit of sand, mud and other debris• Various sizes available
MSP LUBE SPREADERS
Part No. Description Unit Qty
MSS-RS-050 LUBE SPREADER - 50MM EA 1
MSS-RS-080 LUBE SPREADER - 80MM EA 1
MSS-RS-100 LUBE SPREADER - 100MM EA 1
MSS-RS-125 LUBE SPREADER - 125MM EA 1
MSS-RS-150 LUBE SPREADER - 150MM EA 1
Part No. MSS-70188 • A breakaway swivel with standard fuse providing invaluable protection when pulling either fibre optic or coaxial cable• Made from high quality steel• Simple and inexpensive• Other sizes (kN) available• 16mm OD
FUSEABLE SWIVEL - 16MM OD - 2.2KNMSP STAINLESS STEEL HAULING SWIVELS
HAULING SWIVELS
Unit: EA Qty: 1
Part No. MSS-53706 • A breakaway swivel with standard fuse providing invaluable protection when pulling either fibre optic or coaxial cable• Made from high quality Aluminium• Simple and inexpensive• Other sizes (kN) available• 22mm OD
FUSEABLE SWIVEL - 22MM OD - 2.2KN Unit: EA Qty: 1
• Tough swivels designed to handle higher thrust loads for extra cable safety and faster straight pulls• Made from high quality stainless steel• Higher workload ratings than comparably sized swivels• Thrust bearing for tensile load - radial bearing for bending load
Part No. Description Unit Qty
MSS-70137 STAINLESS HAULING 22.2 KN SWIVEL-31.8MM EA 1
MSS-70138 STAINLESS HAULING 31.1 KN SWIVEL-34MM EA 1
MSS-70139 STAINLESS HAULING 44.5 KN SWIVEL-41MM EA 1
MSS-70140 STAINLESS HAULING 111.2KN SWIVEL-64MM EA 1
UNDERGROUND CABLE HANDLING
24
Part No. MSS-26309 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 0.9KN - OR-WHMSP FUSE BOLTS
Unit: EA Qty: 1
Part No. MSS-26310 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 1.0KN - RD-WH Unit: EA Qty: 1
Part No. MSS-26305 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 1.3KN - GR-WH Unit: EA Qty: 1
Part No. MSS-30333 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 1.5KN - WH Unit: EA Qty: 1
Part No. MSS-26306 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 1.8KN - BL-WH Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
25
Part No. MSS-26307 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 1.9KN - YL-WH Unit: EA Qty: 1
Part No. MSS-26308 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 1.97KN - VI-WH Unit: EA Qty: 1
Part No. MSS-25494 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 2.0KN - OR Unit: EA Qty: 1
Part No. MSS-26325 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 2.2KN - VIOLET Unit: EA Qty: 1
Part No. MSS-25493 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and Inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL 2.7KN -YELLOW Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
26
Part No. MSS-26326 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 22mm Aluminium swivel and fuse bolts also available
FUSE FOR 16MM SWIVEL - 3.17KN - BROWN Unit: EA Qty: 1
Part No. MSS-30332 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available
FUSE BOLT -1.5KN WHITE SUIT 22MM SWIVEL Unit: EA Qty: 1
Part No. MSS-34786 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available
FUSE BOLT -2.0KN ORANGE SUIT 22MM SWIVEL Unit: EA Qty: 1
Part No. MSS-34341 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available
FUSE BOLT -2.7KN YELLOW SUIT 22MM SWIVEL Unit: EA Qty: 1
Part No. MSS-34342 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available
FUSE BOLT -3.6KN BLUE-SUIT 22MM SWIVEL Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
27
Part No. MSS-34343 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available
FUSE BOLT -4.5KN GREEN-SUIT 22MM SWIVEL Unit: EA Qty: 1
Part No. MSS-34344 • Fuse bolt to suit a break-away swivel providing invaluable protection when pulling either fibre optic or coaxial cable• Simple and inexpensive• 16mm steel swivel and fuse bolts also available
FUSE BOLT -5.4KN RED- SUIT 22MM SWIVEL Unit: EA Qty: 1
Part No. MSS-NGKA-05 • Dillon AP mechanical dynamometer - uncomplicated operation includes tare function and maximum peak load indicator• Suitable for up to 500kg in 5kg increments• Includes rugged plastic storage case
DYNAMOMETER - 500KG X 5KG- DIALMSP LINE TENSIONERS
LINE TENSIONERS
Unit: EA Qty: 1
Part No. MSS-NGKA-50 • Dillon AP mechanical dynamometer - uncomplicated operation includes tare function and maximum peak load indicator• Suitable for up to 5000kg in 50kg increments• Includes rugged plastic storage case
DYNAMOMETER - 5000KG X 50KG- DIAL Unit: EA Qty: 1
Part No. MSS-HTNS-10KEP-D • Provides continuous pulling tension readout for safer and more efficient cable installation• Self-contained, weather tight case with instructions• Digital readout and preset alarm• Weight capacity 4500kg (10,000lb)
RUNNING LINE TENSIOMETER - 0-4500KG Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
28
• Designed for pulling bundles of Aerial Bundled Conductors (ABC Cables)• Non-conductive materials for safety• Standard is tubular, soft eye and alloy ferrule• Double and offset eye also available
CABAC ABC CABLE STOCKINGS
Part No. Description Unit Qty
CGLV450 CABLE STOCKING 4X50MM2ABC EA 1
CGLV495 CABLE STOCKING 4X95MM2 ABC EA 1
CGLV4150 CABLE STOCKING 4X150MM2ABC EA 1
CABLE STOCKING
• High tension rope and conductor hauling to suit bare or insulated conductor• Copper shoulders provide protection from wear• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request
CABAC HD CU SHOULDER CABLE STOCKINGS
Part No. Description Unit Qty
CG10HD-CS CABLE STOCKING 10-15MM- HD / CU SHOULDER EA 1
CG15HD-CS CABLE STOCKING 15-21MM- HD / CU SHOULDER EA 1
CG20HD-CS CABLE STOCKING 20-29MM- HD / CU SHOULDER EA 1
CG30HD-CS CABLE STOCKING 27-35MM- HD / CU SHOULDER EA 1
• Lace up design allows the grip to be wrapped around the cable at any position secured by a lace• Can be used in central portion of a hauling job to share load• Ideal for retrofit in an industrial or mining application• Variations e.g. galvanised thimbles available on request
CABAC OFFSET EYE LACE UP CABLE STOCKINGS
Part No. Description Unit Qty
CG14LU CABLE STOCKING 14-19MML/UP EA 1
CG20LU CABLE STOCKING 19-28MML/UP EA 1
CG30LU CABLE STOCKING 28-40MML/UP EA 1
CG45LU CABLE STOCK 40-55MM L/UP EA 1
CG60LU CABLE STOCK 55-75MM L/UP EA 1
CG75LU CABLE STOCK 75-95MM L/UP EA 1
CG105LU CABLE STOCKING 95-120MML/UP EA 1
CG165LU CABLE STOCKNG 150/190MML/UP EA 1
UNDERGROUND CABLE HANDLING
29
• Double eye design allows the cable to be lifted into position with one eye, while the other eye is used to anchor the cable to a fixture
• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request
CABAC TUBULAR DOUBLE EYE CABLE STOCKINGS
Part No. Description Unit Qty
CG10DE CABLE STOCKING 10-14MM GAL STRND AL FER EA 1
CG14DE CABLE STOCKING 14-19MM D/EYE EA 1
CG20DE CABLE STOCKING 19-28MM D/EYE EA 1
CG30DE CABLE STOCKING 28-40MM D/EYE EA 1
CG45DE CABLE STOCKING 40-55MM D/EYE EA 1
CG60DE CABLE STOCKING 55-75MM D/EYE EA 1
CG75DE CABLE STOCKING 75-95MM D/EYE EA 1
CG105DE CABLE STOCKING 95-120MMD/EYE EA 1
CG135DE CABLE STOCKING 120-150MM D/EYE EA 1
CG165DE CABLE STOCKING 150-190MM D/EYE EA 1
Part No. CG30DE-GT • Double eye design allows the cable to be lifted into position with one eye, while the other eye is used to anchor the cable to a fixture• Featuring an alloy ferrule and a Galvanised thimble• Variations available on request
CABLE STOCKING 28-40MM D/EYE GAL THIMLECABAC TUBULAR DOUBLE EYE GALVANISED CABLE STOCKING
Unit: EA Qty: 1
• Lace up design allows the grip to be wrapped around the cable at any position secured by a lace• Can be used in central portion of a hauling job to share load• Ideal for retrofit in an industrial or mining application• Variations available on request
CABAC TUBULAR DOUBLE EYE LACE UP SS CABLE STOCKING
Part No. Description Unit Qty
CG45LU/DE-SS-SF-ST CABLE STOCKING 40-55MM L/UP D/EYE SS EA 1
CG60LU/DE-SS-SF-ST CABLE STOCKING 55-75MM L/UP D/EYE SS EA 1
UNDERGROUND CABLE HANDLING
30
• Double eye design allows the cable to be lifted into position with one eye, while the other eye is used to anchor the cable to a fixture
• Featuring Stainless Steel rope, ferrule and thimble• Variations available on request
CABAC TUBULAR DOUBLE EYE SS CABLE STOCKINGS
Part No. Description Unit Qty
CG10DE-SS-SF-ST CABLE STOCKING 10-14MM D/E SS-SF-ST EA 1
CG14DE-SS-SF-ST CABLE STOCKING 14-19MM D/E SS-SF-ST EA 1
CG20DE-SS-SF-ST CABLE STOCKING 19-28MM DOUBLE EYE EA 1
CG30DE-SS-SF-ST CABLE STOCKING 28-40MM D/EYE SS-SF-ST EA 1
CG45DE-SS-SF-ST CABLE STOCKING 40-55MM D/EYE SS-SF-ST EA 1
CG60DE-SS-SF-ST CABLE STOCKING 55-75MM D/E SS-SF-ST EA 1
CG75DE-SS-SF-ST CABLE STOCKING 75-95MM D/E SS-SF-ST EA 1
• Tubular offset eye allows the cable to be passed through the grip and secured at any point along the cable• Mainly used for strain relief• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request
CABAC TUBULAR OFFSET EYE CABLE STOCKINGS
Part No. Description Unit Qty
CG10OE CABLE STOCKING 10-14MM O/SET EA 1
CG14OE CABLE STOCKING 14-19MM O/SET EA 1
CG20OE CABLE STOCKING 19-28MM O/SET EA 1
CG30OE CABLE STOCKING 28-40MM O/SET EA 1
CG45OE CABLE STOCKING 40-55MM O/SET EA 1
CG60OE CABLE STOCKING 55-75MM O/SET EA 1
CG75OE CABLE STOCKING 75-95MM O/SET EA 1
CG105OE CABLE STOCKING 95-120MMO/SET EA 1
CG165OE CABLE STOCKING 150-190MM OFFSET EYE EA 1
Part No. CG20OE-GT • Tubular offset eye allows the cable to be passed through the grip and secured at any point along the cable• Mainly used for strain relief• Featuring an alloy ferrule and a Galvanised thimble• Variations available on request
CABLE STOCKING 19-28MM O/SETCABAC TUBULAR OFFSET EYE GALVINISED CABLE STOCKING
Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
31
• Tubular offset eye allows the cable to be passed through the grip and secured at any point along the cable• Mainly used for strain relief• Featuring Stainless Steel rope, ferrule and thimble• Variations available on request
CABAC TUBULAR OFFSET EYE SS CABLE STOCKINGS
Part No. Description Unit Qty
CG14OE-SS-SF-ST CABLE STOCKING 14-19MM O/SET EA 1
CG20OE-SS-SF-ST CABLE STOCKING 19-28MM O/SET EA 1
CG30OE-SS-SF-ST CABLE STOCKING 28-40MM OFFSET EYE SF SS EA 1
• Tubular single eye used for general cable hauling• Slipped over the end of a cable and grip when pulled• Featuring an alloy ferrule and a soft eye• Variations e.g. galvanised thimbles available on request
CABAC TUBULAR SINGLE EYE CABLE STOCKINGS
Part No. Description Unit Qty
CG10 CABLE STOCKING 10-14MM EA 1
CG14 CABLE STOCKING 14-19MM EA 1
CG20 CABLE STOCKING 19-28MM EA 1
CG30 CABLE STOCKING 28-40MM EA 1
CG45 CABLE STOCKING 40-55MM EA 1
CG60 CABLE STOCKING 55-75MM EA 1
CG75 CABLE STOCKING 75-95MM EA 1
CG105 CABLE STOCKING 95-120MM EA 1
CG135 CABLE STOCKING 120-150MM EA 1
CG165 CABLE STOCKING 150-190MM EA 1
• Lace up design allows the grip to be wrapped around the cable at any position secured by a lace• Can be used in central portion of a hauling job to share load• Ideal for retrofit in an industrial or mining application• Variations available on request
CABAC TUBULAR SINGLE EYE LACE UP SS CABLE STOCKING
Part No. Description Unit Qty
CG20LU-SS-SF-ST CABLE STOCKING 19-28MML/UP S/S S/F S/T EA 1
CG30LU-SS-SF-ST CABLE STOCKING 28-40MML/UP SS-SF-ST EA 1
CG75LU-SS-SF-ST CABLE STOCK 75-95MM L/UP SS/SF/ST EA 1
CG105LU-SS-SF-ST CABLE STOCK 95-120MM L/UP SS/SF/ST EA 1
UNDERGROUND CABLE HANDLING
32
• Tubular single eye used for general cable hauling• Slipped over the end of a cable and grip when pulled• Featuring Stainless Steel rope, ferrule and thimble• Variations available on request
CABAC TUBULAR SINGLE EYE SS CABLE STOCKINGS
Part No. Description Unit Qty
CG10-SS-SF-ST CABLE STOCKING 10-14MM SS/SF/ST EA 1
CG14-SS-SF-ST CABLE STOCKING 14-19MM SS/SF/ST EA 1
CG20-SS-SF-ST CABLE STOCKING 19-28MM SS/SF/ST EA 1
CG30-SS-SF-ST CABLE STOCKING 28-40MM SS/SF/ST EA 1
CG45-SS-SF-ST CABLE STOCKING 40-55MM SS/SF/ST EA 1
CG60-SS-SF-ST CABLE STOCKING 55-75MM SS/SF/ST EA 1
CG75-SS-SF-ST CABLE STOCKING 75-95MM SS/SF/ST EA 1
• Used when there is a possibility of rotation or spinning, passing from the pilot rope to the cable, or vice-versa
• Low friction ball bearing swivel made from stainless steel• Screwdriver slots in pins for easy removal• Clevis/Eye type is also available
CABAC SWIVELS
Part No. Description Unit Qty
CGSSSW19CC BEARING SWIVEL 19MM DIAMETER 1.5T U.T.S EA 1
CGSSSW25CC BEARING SWIVEL 25MM DIAMETER 2.5T U.T.S EA 1
Part No. MSS-C1405-AU • Skid mounted hydraulic pull and assist double capstan winch with capstan tilt function and rope take-up drum• User friendly power mounted controls• Winch stops pulling at selected tension without engine shut down• Removable take-up drum for easy rope removal• Pulling capacity- 500kg large capstan, 1000kg small capstan
TILTING CAPSTAN F OP WINCH - SKIDMSP CABLE PULLERS
CABLE PULLERS
Unit: EA Qty: 1
Part No. MSS-H2500 • 240 Volt single phase cable puller with a dual pulling capacity of 2500kg and 1500kg• Overload protection switch - ensures automatic shut-off• Electromagnetic spring-applied fail safe brake• Rugged high power induction motor for proven reliability
240V CAPSTAN WINCH - 2.5TON Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
33
Part No. MSS-MGA-070 • Suitable for storage in a station wagon or sedan• For providing a safe and sheltered working environment• Colour: Yellow
FOLDAWAY BARRIER FRAME SET- NO ROOFMSSP GUARDS
MANHOLE EQUIPMENT
Unit: EA Qty: 1
Part No. MSS-SMTF38 • NOT approved for Telstra use• For providing a safe and sheltered working environment• Colour: Yellow
MANHOLE BARRIER GUARD - YELLOW - NO ROOF Unit: EA Qty: 1
Part No. MSS-MGA-140Y • For providing a safe and sheltered working environment• Approved for Telstra use• Rugged and reliable• Colour: Yellow
MANHOLE BARRIER SET - NO ROOF Unit: EA Qty: 1
Part No. MSS-MGA-140RY • Manhole barrier set to suit a tent frame• Manhole guard tent sold separately - Part No. MSS-TENT-01• For providing a safe and sheltered working environment• approved for Telstra use
MANHOLE BARRIER SET WITH ROOF FRAME Unit: EA Qty: 1
Part No. MSS-TENT-01 • Waterproof canvas• Window and door flap design• Frame sold separately - Part No. MSS-MGA-140RY• For providing a safe and sheltered working environment
MANHOLE GUARD TENT WITH ROOF WINDOW Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
34
Part No. MSS-TEL83-41 • Designed to protect workers from the elements - bright in colour, the tent is easily seen by oncoming traffic• Unique hub design - tent pops up or down in seconds• Durable water repellent fabric• Features adjustable rod ends for side wall tension• Fire resistant
FIBRE SPLICING TENT - 1.8X1.8X1.8MTR Unit: EA Qty: 1
Part No. MSS-GAT-LONG • Long handle lid lifter is used in pairs to break stubborn, dirt ingress seals and to lift medium-duty pit lids and grates• Use with the short handle key (Part No. MSS-GAT-SHORT)• Weight: 1.8kg• Handle length: 740mm
GATTIC - LID LIFTER - LONG HANDLEMSP PIT KEYS AND BREAKERS
PIT KEYS AND BREAKER
Unit: EA Qty: 1
Part No. MSS-GAT-SMALL • Short handle lid lifter is used in pairs to break stubborn, dirt ingress seals and to lift smaller pit lids and grates• Small ‘D’ handle assists in breaking the dirt locked seal• Use with the long handle key (Part No. MSS-GAT-LONG)• Weight: 1.8kg
GATTIC - LID LIFTER - SHORT HANDLE Unit: EA Qty: 1
Part No. MSS-PB-100 • For use with Telstra pit keys• Lift stubborn lids with ease• Open manhole lids that may be stuck or jammed• Cover seal breaker also available (Part No. MSS-TEL116-00151A)
MANHOLE LID BREAKER Unit: EA Qty: 1
Part No. MSS-TEL116-00151A • Helps to ease man hole covers that have not been lifted for a long time• Manhole lid breaker also available Part No. MSS-PB-100
COVER SEAL BREAKER Unit: EA Qty: 1
UNDERGROUND CABLE HANDLING
35
Part No. MSS-TEL116-00152 • Standard pit key
M KEY - PIT KEY - 600MM Unit: EA Qty: 1
Part No. MSS-TEL116-00153 • Standard pit key
PIT L KEY - 670MM Unit: EA Qty: 1
Part No. MSS-TEL075-00122 • Quality extractor tool• Remove manhole keyhole plugs with ease
KEYHOLE PLUG EXTRACTOR TOOL Unit: EA Qty: 1
CABLE LAYING & EQUIPMENT
36
CG30OE-SS-SF-ST 31
CG30OE 30
CG45-SS-SF-ST 32
CG45 31
CG45DE-SS-SF-ST 30
CG45DE 29
CG45LU/DE-SS-SF-ST 29
CG45LU 28
CG45OE 30
CG60-SS-SF-ST 32
CG60 31
CG60DE-SS-SF-ST 30
CG60DE 29
CG60LU/DE-SS-SF-ST 29
CG60LU 28
CG60OE 30
CG75-SS-SF-ST 32
CG75 31
CG75DE-SS-SF-ST 30
CG75DE 29
CG75LU-SS-SF-ST 31
CG75LU 28
CG75OE 30
CGLV4150 28
CGLV450 28
CGLV495 28
CGSSSW19CC 32
CGSSSW25CC 32
FTCM30 4
FTGJ20 4
FTR6 4
FTRC 4
MSS-100505001 10
MSS-11FLEX 7
MSS-11TR-125 7
MSS-11TR-150 7
MSS-11TR-200 7
MSS-11TR-250 7
MSS-11TR-300 7
MSS-11TR-350 7
MSS-11TR-400 7
MSS-25493 25
MSS-25494 25
MSS-26305 24
45-235 11
CG10-SS-SF-ST 32
CG10 31
CG105 31
CG105DE 29
CG105LU-SS-SF-ST 31
CG105LU 28
CG105OE 30
CG10DE-SS-SF-ST 30
CG10DE 29
CG10HD-CS 28
CG10OE 30
CG135 31
CG135DE 29
CG14-SS-SF-ST 32
CG14 31
CG14DE-SS-SF-ST 30
CG14DE 29
CG14LU 28
CG14OE-SS-SF-ST 31
CG14OE 30
CG15HD-CS 28
CG165 31
CG165DE 29
CG165LU 28
CG165OE 30
CG20-SS-SF-ST 32
CG20 31
CG20DE-SS-SF-ST 30
CG20DE 29
CG20HD-CS 28
CG20LU-SS-SF-ST 31
CG20LU 28
CG20OE-GT 30
CG20OE-SS-SF-ST 31
CG20OE 30
CG30-SS-SF-ST 32
CG30 31
CG30DE-GT 29
CG30DE-SS-SF-ST 30
CG30DE 29
CG30HD-CS 28
CG30LU-SS-SF-ST 31
CG30LU 28
INDEX
MSS-26306 24
MSS-26307 25
MSS-26308 25
MSS-26309 24
MSS-26310 24
MSS-26325 25
MSS-26326 26
MSS-30332 26
MSS-30333 24
MSS-306311 10
MSS-34341 26
MSS-34342 26
MSS-34343 27
MSS-34344 27
MSS-34786 26
MSS-4.5-100 7
MSS-4.5-30 7
MSS-4.5-60 7
MSS-4.5-80 7
MSS-4.5FLEX 7
MSS-4JZ-DZ255S 14
MSS-53706 23
MSS-6FLEX 7
MSS-6TR-100 7
MSS-6TR-120 7
MSS-6TR-150 7
MSS-6TR-200 7
MSS-6TR-60 7
MSS-6TR-80 7
MSS-70137 23
MSS-70138 23
MSS-70139 23
MSS-70140 23
MSS-70188 23
MSS-9FLEX 7
MSS-9TR-100 7
MSS-9TR-125 7
MSS-9TR-150 7
MSS-9TR-200 7
MSS-9TR-250 7
MSS-BM100 17
MSS-BM125 17
MSS-BM150 17
MSS-C-1250-0001-01 20
CABLE LAYING & EQUIPMENT
37
MSS-C-1254-001-01 20
MSS-C1405-AU 32
MSS-CCG-028 17
MSS-CCG-035 17
MSS-CCG-050 17
MSS-CCG-080 17
MSS-CCG-100 17
MSS-CCG-125 17
MSS-CCG-150 17
MSS-CDT-500 13
MSS-CLS-050 17
MSS-CLS-080 17
MSS-CLS-100 17
MSS-CLS-125 17
MSS-CLS-150 17
MSS-CRC-050 22
MSS-CRC-080 22
MSS-CRC-100 22
MSS-CRC-125 22
MSS-CRC-150 22
MSS-CRS350 13
MSS-DB-400 14
MSS-DB-630 14
MSS-DB-660 14
MSS-DB-900 14
MSS-DBL-035 21
MSS-DBL-050 21
MSS-DBL-063 21
MSS-DBL-080 21
MSS-DBL-100 21
MSS-DBL-125 21
MSS-DBL-150 21
MSS-DBL-190 21
MSS-DBL-225 21
MSS-DJS-58T 14
MSS-DPL-500 21
MSS-DPM-010 22
MSS-DPM-014 22
MSS-DPM-015 22
MSS-DPM-018 22
MSS-DPM-020 22
MSS-DPM-022 22
MSS-DPM-030 22
MSS-DPM-050 22
MSS-DPM-080 22
MSS-DPM-100 22
MSS-DPM-125 22
MSS-DPM-150 22
MSS-DRR-1000 14
MSS-EBK2-1300K 21
MSS-FS-050 18
MSS-FS-063 18
MSS-FS-080 18
MSS-FS-100 18
MSS-FS-125 19
MSS-FS-150 19
MSS-GAT-LONG 34
MSS-GAT-SMALL 34
MSS-GCG30V 5
MSS-H2500 32
MSS-HTNS-10KEP-D 27
MSS-IFS-080 16
MSS-IFS-100 16
MSS-IFS-125 16
MSS-IFS-150 16
MSS-JK10.0-8.0 8
MSS-JK4.5-3.0 8
MSS-JK6.0-8.0 8
MSS-JK6.5-4.5 8
MSS-LN1477-4 19
MSS-LN1477 19
MSS-LN1478 19
MSS-LPPHTA12 20
MSS-LPPHTA20 20
MSS-LPPHTG16 20
MSS-MGA-070 33
MSS-MGA-140RY 33
MSS-MGA-140Y 33
MSS-NGKA-05 27
MSS-NGKA-50 27
MSS-NTR-120 15
MSS-NTRA-120 15
MSS-PB-100 34
MSS-PMCG-100 17
MSS-PMRG-140 18
MSS-RFL-11-125TR 8
MSS-RFL-11-150TR 8
MSS-RFL-11-200TR 8
MSS-RFL-11-250TR 8
MSS-RFL-11-300TR 8
MSS-RFL-11-350TR 8
MSS-RFL-11-400TR 8
MSS-RFL-4.5-30 8
MSS-RFL-4.5-60 8
MSS-RFL-4.5-80 8
MSS-RFL-6-100TR 8
MSS-RFL-6-120TR 8
MSS-RFL-6-150TR 8
MSS-RFL-6-60TR 8
MSS-RFL-6-80TR 8
MSS-RFL-9-100TR 8
MSS-RFL-9-125TR 8
MSS-RFL-9-150TR 8
MSS-RFL-9-200TR 8
MSS-RFL-9-250TR 8
MSS-RS-050 23
MSS-RS-080 23
MSS-RS-100 23
MSS-RS-125 23
MSS-RS-150 23
MSS-RTR-140 15
MSS-RTRA-140 15
MSS-SLS-05T 13
MSS-SLS1-2T 13
MSS-SLS3-4T 13
MSS-SMTF38 33
MSS-SV3366 10
MSS-TCH-22MF 5
MSS-TCR-200 15
MSS-TEL075-00122 35
MSS-TEL116-00151A 34
MSS-TEL116-00152 35
MSS-TEL116-00153 35
MSS-TEL414-105 9
MSS-TEL414-130 9
MSS-TEL414-50 9
MSS-TEL414-77 9
MSS-TEL414-82 8
MSS-TEL414-84 9
CABLE LAYING & EQUIPMENT
38
MSS-TEL83-41 34
MSS-TENT-01 33
MSS-TFL-22 5
MSS-THL-2290 6
MSS-THR-223M 5
MSS-TRE-22 6
MSS-TRGM-100-2 16
MSS-TRGM-100-3 16
MSS-TRGM-100 16
MSS-TX405C 10
MSS-WBC-050 22
MSS-WBC-080 22
MSS-WBC-100 22
MSS-WBC-125 22
MSS-WBC-150 22
MSS-WBC-200 22
P611001 11
P611002 11
P611003 11
P611004 11
P611005 11
P611007 11
P611009 11
P802163 3
P802164 3
PTS20M 3
PTS30M 3
In support of our policy of continuous product improvement we reserve the right to change materials and specifications without notice. Drawings, where used, are not to scale. All dimensions are in millimetres and sizes given are approximate. Where possible, technical MSDS data sheets are made available on the website. All products should be installed and used in accordance
with manufacturer’s instructions provided. Warning: products may be the subject of registered designs and patents. Refer to website for terms and conditions on warranty.
Every effort has been made to ensure accuracy of content. However no liability will be met by Legend Performance Technology or its suppliers for any errors or ommisions. Product data and information is not binding.
All brands and logos are registered trademarks and are subject to copyright laws.
No part of this catalogue can be reproduced without consent of Legend Performance Technology.
OVERHEADLPTV0117
Top Related