OWNER’S MANUALYour Pioneer 202 is an advanced technology metal detector which incorporates

patented microprocessor-controlled technology, designed for a variety ofapplications including coinshooting, relic hunting, and general purpose detecting.The Pioneer 202 is a motion detector; movement over an object is required inorder for the machine to detect the object and emit a tone. Alternatively, you cansweep a metal object over a motionless searchcoil.

Before using your Pioneer 202, it is important to read these instructions. Thismanual's description of detection concepts and types of metals is necessary toavoid frustration if you are new to the hobby of metal detecting.

THIS METAL DETECTOR HAS TWO TYPES OF OPERATING MODES:1. ALL METAL DETECTION

All metals will be detected. 2. DISCRIMINATE, NOTCH, and AUTO NOTCH modes

In any of these three detection modes, the detector will emit differenttones, depending upon the type of metal present. The characteristics areadjustable. Depending on the detector control settings, some metals willalso be eliminated from detection.

DISCRIMINATE: Eliminates iron and trash items with the use of theDISC/NOTCH knob.

NOTCH: Provides an adjustable rejection "window" to eliminate undesirablemetals from detection. Move the rejection "window" with theDISC/NOTCH knob.

AUTO NOTCH: Provides a pre-set rejection "window", automaticallyeliminating most pull-tabs and trash items from detection.

CAUTION: • Do not test the detector by placing coins or metal objects on the floor.

Most floors contain metal, which will cause interference.• Use 9-VOLT ALKALINE batteries only.

DO NOT USE INDOORS. LIGHTS AND HOUSEHOLD APPLIANCES EMITELECTROMAGNETIC FIELDS WHICH INTERFERE WITH THE DETECTOR’S OPERATION

2

TABLE OF CONTENTSTERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Easy Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

INSTALLING BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

DEMONSTRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Turning on Your Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Set the Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Reading the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Low Battery Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Depth Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

SENSITIVITY ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

MODES OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 & 12

AUDIO TARGET ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

IN THE FIELD TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Pinpointing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Coil Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 & 15

METAL DETECTING APPLICATIONS . . . . . . . . . . . . . . . . . . . . . .16

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

CARE & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

TREASURE HUNTER’S CODE OF ETHICS . . . . . . . . . . . . . . . . . . .19

WARRANTY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .BACK COVER

The BOUNTY HUNTER PIONEER series of metal detectors is notassociated or connected in any way with Pioneer Corporation or itsPIONEER brand audio and video products or other products.

3

TERMINOLOGYThe following terms are used throughout the manual, and are standardterminology among detectorists.ELIMINATION

Reference to a metal being "eliminated" means that the detector will not emit a tone,nor light up an LCD indicator, when a specified object passes through the coil’sdetection field.

DISCRIMINATIONWhen the detector emits different tones for different types of metals, and when thedetector "eliminates" certain metals, we refer to this as the detector "discriminating"among different types of metals. Discrimination is a fixed-start-point elimination system.

NOTCHNotching is the elimination of an item, or range of items, within the metallic spectrum.We "notch-out" an object selectively. Objects to the left and right on the metallicspectrum are retained. Notching creates a variable rejection window.

RELICA relic is an object of interest by reason of its age or its association with the past.Many relics are made of iron, but can also be made of bronze or precious metals.

IRONIron is a common, low-grade metal that is often an undesirable target in certain metaldetecting applications. Examples of undesirable iron objects are old cans, pipes,bolts, and nails. Sometimes, the desired target is made of iron. Propertymarkers, for instance, can contain iron. Valuable relics can also be composed ofiron; cannon balls, old armaments, and parts of old structures and vehicles canalso be composed of iron.

FERROUSMetals which are made of, or contain, iron.

PINPOINTINGPinpointing is the process of finding the exact location of a buried object. Long-buriedmetals can appear exactly like the surrounding earth, and can therefore be very hardto isolate.

PULL-TABSDiscarded pull-tabs from beverage containers are the most bothersome trash itemsfor treasure hunters. They come in many different shapes and sizes. We haveincorporated special features into the detector to let you automatically eliminate themost common types, using the AutoNotch Mode. Since there are many differenttypes, some must be "Notched-Out" manually.

GROUND BALANCEGround Balancing is the ability of the detector to ignore, or "see through," the earth’snaturally occurring minerals, and only sound a tone when a metal object is detected.

WATERPROOFThe search coil can be submerged in water. The control housing and cable-to-housingconnection must, however, stay dry.

COINSHOOTINGFinding buried coins is the most popular metal detecting application. The most valuableare very old; take care in unearthing them to avoid damage.

CACHE HUNTINGPronounced “cash”. A cache is a buried or hidden valuable stored inside a case, strongbox, or bag.

4

ASSEMBLYAdjusting the Arm RestThe arm rest may be movedforward or backwards byremoving the single screw andnut, and then repositioning the2-piece arm rest. Users withshorter arms may find the armrest more comfortable in theforward position. In order tomove the arm rest backwards,the plastic plug must beremoved from the aluminumtube.

Arm Rest Strap (not included)Some users prefer to use a strapwhen swinging the detectorvigorously, in order to hold thedetector secure against the arm.The strap may be purchased asan optional accessory.

The detector can also be usedwithout the strap with nocompromise to detector balanceand stability under mostconditions.

KnurledKnob

Nut

Screw

LockingCollar

CablePlug

Hand-grip

S-Rod

Armrest

SearchCoilCable

Search Coil

Optional Arm Strap

5

ASSEMBLY

Assembly is easy and requires no tools.●1 Position detector upright.

●2 Rotate the LOCKINGCOLLAR fully in a counterclockwise direction.

●3 Insert your finger inside thetube and make sure theINTERNAL CAM LOCK isflush with the inside of thetube.

●4 Insert the LOWER STEM intothe S-ROD.

●5 Rotate the LOWER STEM until the SILVER BUTTON locates in the hole.

●6 Twist the LOCKING COLLAR fully in the clockwise direction until it locks.

●7 If your detector has 3 tubes and 2 locking collars, repeat this processon the Middle Stem.

●8 Position the Lower Stem (the straight tube) with the Silver Buttontoward the back. Using the Bolt and Knurled Knob, attach theSearchcoil to the plastic extension protruding from the Lower Stem.

●9 Press the button on the upper end of the Lower Stem, and slide theLower Stem into the S-Rod.

Adjust the Stem to a length that letsyou maintain a comfortable uprightposture, with your arm relaxed atyour side, and the Searchcoil parallelto the ground in front of you.

●10 Wind the Cable securely around theStem.

●11 Insert the Plug into the matchingConnector on the right underside ofthe Detector Body. Be sure that thekey-way and pins line up correctly.

Caution: Do not force the plug in. Excessforce will cause damage.To disconnect the cable, pull onthe plug.Do not pull on the cable.

S-Rod

ConnectorPlug

DetectorBody

S-ROD

LOCKINGCOLLAR

INTERNALCAM LOCK

SILVER BUTTON

MIDDLESTEM

S-ROD MIDDLE STEM

Connectoron back ofunit Body

6

IMPORTANT: Always use ALKALINE batteries only.Do not use heavy duty batteries.

Always remove the batteries for prolonged storage.

CHECK THE BATTERIES if your detector exhibits any of the followingsymptoms:

●1 The unit does not turn on.●2 Low speaker volume.●3 Unit beeps continuously or erratically.

The Low Battery indicator light will come on and stay on whenever thebatteries need replacing. It should flash momentarily when the PowerSwitch is turned off. The flashing indicator tells you that your batteries arein good condition.

IMPORTANT: Your Pioneer 202 metal detector requires two 9-Volt ALKALINE batteries.

Follow these steps to install the batteries.

●1 Carefully remove the battery compartment door by pressing the releaseclip on the right side of the door.

●2 Snap one battery onto each of the terminals and place the batteries in-side the com-partment.Insert booth ofthe batterieswith terminalsfacing inward.

●3 Replace thecompartmentdoor by carefullyinserting oppo-site side of clipfirst. Then pressdown on clipside until batterydoor snaps intoplace.

BATTERIES

ReleaseClip

Both Batteriesterminalsfacing in

7

PIONEER 202 DEMONSTRATIONHere is a quick way to demonstrate the basic features of your PIONEER 202.

I. Supplies Needed• A quarter (25¢) • A penny (1¢) • A dime (10¢)• A nickel (5¢) • Small piece of aluminum foil • A nail

II. Position your Pioneer 202• Place the detector on a table, with the searchcoil hanging over the edge.• Be sure that the searchcoil is far away from walls or metal objects.

Keep the searchcoil away from any metal in the table.• Turn off appliances or lights which cause electromagnetic interference

III. Beginning Switch Settings• Right Knob (DISC/NOTCH) —

100% counterclockwise to low• Left Knob (SENSITIVITY) —

click on and set to 3:00 (3/4 turn)• Do not press any touchpads

IV. All Metal DetectionA. Wave all objects under the searchcoil

• NOTICE THE TONES

V. Discriminate ModeA. Turn the right knob (DISC/NOTCH) slowly to the right past the "DISC"

indication.B. Wave all objects under the searchcoil at different "DISC" settings.

• NOTICE THE DIFFERENT TONES• NOTICE THE METALS ELIMINATED

VI. Notch ModeA. Press the NOTCH touchpadB. Right knob (DISC/NOTCH) 100% counterclockwise to lowC. Wave all objects under the searchcoil while

slowly turning the right knob clockwise.• NOTICE THE DIFFERENT TONES• NOTICE THE METALS ELIMINATED

VII. Auto Notch ModeA. Press the AUTO NOTCH touchpadB. Right knob (DISC/NOTCH) 100% counterclockwise to lowC. Wave all objects under the searchcoil while

slowly turning the right knob clockwise.• NOTICE THE DIFFERENT TONES• NOTICE THE METALS ELIMINATED

8

TURNING ON YOUR DETECTORTurn the left knob (SENSITIVITY) to the right. As the knob clicks to the "On"position, the detector sounds three beeps, the LCD arrows appearmomentarily, and the unit pre-sets to the DISC/ALL METAL mode of operation.

SET THE MODE

1. ALL METALA. Press the DISC/ALL METAL touchpadB. Turn the right knob (DISC/NOTCH) to the left.

The unit will emit sound when passing over all types of metal objects.The ALL METAL mode offers the greatest depth detection capability.

2. DISCRIMINATEA. Press the DISC/ALL METAL touchpad B. Slowly turn the right knob (DISC/NOTCH) clockwise.

As you turn the knob clockwise the detector will first eliminate smalliron objects such as nails. When rotated clockwise, large iron objects areeliminated, followed by trash items such as foil and aluminum.

3. NOTCHPress the NOTCH touchpad, and the detector will automatically reject iron.Turn the DISC/NOTCH knob clockwise for selective elimination of variousjunk items while still detecting nickels, silver and copper coins, and smallgold items. NOTCH eliminates medium tone trash items while stilldetecting valuable low and high tone metals. (audio tone ID is discussedlater).

4. AUTO NOTCH Press the AUTO NOTCH touchpad, and the detector will automaticallyreject iron and most pull-tabs. Nickels and most small gold rings will beretained. The DISC/NOTCH knob creates a rejection "window" whichcan be moved as it is turned clockwise. With this mode, you can rejectscrew caps and zinc (post 1982) pennies as the DISC/NOTCH control isturned clockwise, but still detect valuables with low and high tones.

Note: If you are not sure of your current mode setting, simply press the desiredtouch-pad again.

BASIC OPERATION

9

READING THE DISPLAYThe Liquid Crystal Display (LCD) showsthe PROBABLE identification of thetargeted metal, as well as the PROBABLEdepth of the target, in inches.

Pass the searchcoil repeatedly over atarget, and observe the target readout.The detector will register a repeated,unchanging target identification when aburied target has been located andidentified. If, upon repeated passes overthe same spot, the target identificationreads inconsistently, the target is probablya trash item, or oxidized metal. Withpractice, you will learn to unearth only therepeatable signals.

The segment identifications are highlyaccurate, when detecting the objectsdescribed on the label. For example, ifyou pass the coil repeatedly over a nickel,your detector will repeatedly register anickel. However, if you repeatedly registera nickel, for an unknown buried object,you could be detecting some othermetallic object with the same magneticsignature as a nickel.

GOLD TARGETS Gold objects willregister on the left side of the LCD scale.

Gold flakes will register under Iron/FoilSmall gold items will register under PullTab.Medium-sized gold items will registerunder S-caps.Large gold items will register as Zinc 1¢.

SILVER TARGETS: Silver objects willregister to the right of the scale, under25¢, 50¢, or $1, depending on the sizeof the object. The larger the object, thefarther to the right it will register.

IRON/FOIL: All sizes of iron andaluminum objects will register on thefar-left side of the scale. This couldindicate a worthless item such as a nail,or a more valuable historic iron relic.

PULL TAB: All older pull tabs frombeverage cans will register here. Mostnewer pull tabs will register here. Manygold rings will also register here.

S-CAPS: Older screw caps from glassbottles will register here. Large goldrings, like a class ring, could also registerhere. Some non-U.S. coins of recentvintage will also register here.

1¢ ZINC: Newer pennies (post-1982)will register here. Many non-U.S. coinsof recent vintage will also register here.

10¢: Dimes and pre-1982 pennies willregister here. Older, pre-1982, penniesare composed of copper, which has ametallic signature similar to a dime.

Caution: The target indications arevisual references. Many other types ofmetal can fall under any one of thesecategories. You will experience atrash-to-treasure ratio when treasurehunting. The more you practice, thelower you will push your trash-to-treasure ratio. While the Pioneer 202will eliminate or indicate the presenceof most common trash items, it isimpossible to accurately classify ALLburied objects. The LCD provides avisual reference to minimize thedetection of trash objects. By using thetarget ID in conjunction withdiscrimination control and the three-tone audio identification system(discussed later), you can furtherreduce the trash-to-treasure ratio.

LCD TARGET DISPLAY

10

SENSITIVITY ADJUSTMENT

BATTERY & DEPTH INDICATORSThe LOW BATT indicator will flash asthe unit is powered on. If the indicatorcomes on and stays on, replace thebatteries.

DEPTH INDICATOR:The Depth Indicator is accurate forcoin-sized objects. It indicates thedepth of the target, in inches. Largeand irregularly-shaped objects willyield less reliable depth readings

When passing over an object, thedepth indicator will light up and stayilluminated until another object isscanned. Pass repeatedly over thesuspected target and pause briefly atthe end of each sweep to read your

display. Repeated indication at thesame depth level indicates an accuratetarget detector. If the depth indicationvaries with each sweep, try sweepingat different angles; there may be morethan one target present. With practice,you will learn the difference betweenaccurate readings, multiple targets,and highly erratic readings whichevidence trash or irregularly shapedobjects.

Depth indicator locked on 8 inches

The principle use for the SENSITIVITYknob is to eliminateELECTROMAGNETIC INTERFERENCE(EMI). EMI is both naturally-occurringand man-made. Common sources ofEMI are power lines, both suspendedand buried, and broadcastingantennas. Machinery, when inoperation, can also produce EMI.

EMI comes from most householdappliances, so YOUR DETECTOR CANBEHAVE VERY ERRATICALLYINDOORS. If you want to test it indoors,turn off the TV and microwave. If youhave lights with dimmer switches, alsoturn these off; dimmer switches canproduce lots of EMI.

If your detector chatters with the

SENSITIVITY knob in the 100%clockwise position, reduce thesensitivity until the chatter stops(usually to the 1:00 or 3:00 position).

If you suspect the presence of deepertargets underneath a shallower target,reduce the SENSITIVITY to eliminatethe detection of the deeper target toproperly locate and identify theshallower target

ALL METAL MODE:There are two ways to enter theALL-METAL mode.1) Turn the right knob (Disc/Notch) left

to the furthest counterclockwiseposition. Then Press the Disc/AllMetal touch pad.or

2) Turn the right knob (Disc/Notch) leftto the furthest counterclockwiseposition. Then turn the detector on.(The detector always defaults tothe Disc/All Metal mode when firstpowered on).

DISCRIMINATION MODE:To enter DISCRIMINATION mode,1) Press the Disc/All Metal touch pad,

and2) Turn the Disc/Notch control knob

clockwise past the “Disc”indication.In the DISCRIMINATION mode, thedetector will emit three distinct

tones, depending on the type ofmetal detected.As you turn the Disc Knobclockwise, you will progressively“discriminate out,” or eliminatefrom detection, different types ofmetals.Refer to the illustration below as areference for the levels required todiscriminate out different objects.

The DISCRIMINATION mode is afixed-start-point system. As you turnthe knob to the right, more objects areprogressively eliminated, including theitems to the left. UseDISCRIMINATION for coin-shooting

and detecting in trashy areas.

NOTCH MODE:To enter NOTCH mode, press theNotch touch pad.In NOTCH mode, iron is automaticallyeliminated.

11

MODES OF OPERATION

ALL METAL TOUCHPAD

DISC TOUCHPAD

NOTCH TOUCHPAD

12

NOTCH then gives the user a variablerejection window. In this mode, youcan eliminate items in the middle ofthe metallic spectrum, but still detectitems to the left of the scale, asfollows:

NOTCH is most useful to “notch out”specific unwanted items. If youencounter certain bothersome trashitems, program their rejection intoyour detector as follows:1) Turn the Disc/Notch knob 100%

counterclockwise.2) Pass the undesirable object under

the searchcoil.3) Turn the Disc/Notch knob slowly

clockwise until the object is nolonger detected.

Use the NOTCH mode for coin-shooting,jewelry hunting, or for your own

customized hunt.

AUTO NOTCH MODETo enter the AUTO NOTCH mode,press the Auto Notch touch pad. InAUTO NOTCH mode, iron, most pulltabs, and screw caps areautomatically eliminated.

In addition, you can turn the Disc/Notchcontrol to selectively eliminate moreitems beyond the pre-programmedones. The Disc/Notch control operatesin this mode in the same manner asoutlined in the NOTCH modeinstructions, except that AUTO NOTCHdoes not eliminate the more valuablenickels.Use AUTO NOTCH for press-and-gotreasure hunting in applications likecoin-shooting, and jewelry hunting.

AUTO NOTCH TOUCHPAD

IRO

N

5¢ PTA

B

SCA

P

ZIN

C

10¢

25¢

50¢

1¢

SELECTIVELY “NOTCH OUT” THESE

USING HEADPHONESUsing headphones (not included) improves battery life, and prevents thesounds from annoying bystanders.It also allows you to hear subtle changes in the sound more clearly,particularly if searching in a noisy location. For safety reasons, do not useheadphones near traffic or where other dangers are present. This device isto be used with interconnecting cables/headphone cables shorter than threemeters.

MODES OF OPERATION

13

AUDIO TARGET IDDepending on the operating modeand Disc/Notch control setting, thePioneer 202 emits three distinct toneswhich classify metal objects intocategories.

IRON & STEEL:In the DISCRIMINATION mode mostiron and steel objects will induce a lowtone. Highly oxidized iron can induce ahigh tone, depending on theDisc/Notch control setting. Forinstance, some rusted bottle caps willinduce a high tone and indicate to theright of the LCD target display.

GOLD:Gold objects will induce a low ormedium tone, depending on theirsizes. Very small gold objects willindicate on the left-most segment.Large gold objects will read under theZinc segment. If you are goldprospecting, you will usually belooking for natural gold in an areawhich it does not contain much trash,and can therefore ignore the specificsegment descriptions.

PULL TABS:Pull tabs are the most bothersometrash items for detectorist. Most willinduce a medium tone. Most will beeliminated automatically in the AUTONOTCH mode, or alternatively bemanually “notched out” in NOTCHmode with the Disc/Notch control. Theolder pull tabs (those not attached tothe can after opening) are sometimesbroken in half; these broken tabs caninduce low tones. Highly oxidized pulltabs can also induce high tones.

It can be very difficult to differentiatepull tabs from gold rings. When theyboth induce medium tones, you mightnotice a “double beep” from a goldring but a “single beep” from pull tabs.To achieve this distinction, sweep thesearchcoil very slowly, and at differentangles. Two tones might signal as thedetector passes over each side of theround ring.

COPPER, SILVER & BRASS:Most valuable coins are composed ofthese metals and will usually induce ahigh tone. Valuable objects other thancoinage can also be composed ofcopper, silver and brass.

Audio Target Identification (ATI) classifies metals into three categories.

LOW TONE

Nails & Bottle Caps,Gold & Nickel

MEDIUM TONE

Old & New Pull Tabs, ZincPennies (Post 1982)

HIGH TONE

Copper, Silver & BrassCopper Pennies (Pre 1982)

14

IN THE FIELD TECHNIQUES

When pinpointing a target, try drawing an “X”,as illustrated, over where the tone is induced.

PINPOINTING

Accurate pinpointing takes practiceand is best accomplished by“X-ing” the target area.

1. Once a buried target is indicatedby a good tone response,continue sweeping the coil overthe target in a narrowingside-to-side pattern.

2. Take visual note of the place onthe ground where the “beep”sounds.

3. Stop the coil directly over thisspot on the ground.

4. Now move the coil straightforward and straight backtowards you a couple of times.

5. Again make visual note of thespot on the ground at whichthe “beep” sounds.

6. If needed, “X” the target atdifferent angles to “zero in” onthe exact spot on the ground atwhich the “beep” sounds.

COIL MOVEMENT

When swinging the coil, becareful to keep it level with theground about one inch from thesurface. Never swing the coil likea pendulum.

CORRECT

WRONG

Thecoilshouldbe swungin ahalf-circlemovementasillustratedhere.Repeat thismotionevery stepyou take toguarantee thatthe area is beingcovered thoroughly.

15

After selecting your operating mode,swing the searchcoil gently side-to-side, slightly overlapping each sweepas you move forward. Make sure youkeep your searchcoil approximately 1inch above the ground as you search.Raising it in the sweep, or at the endsof your sweep, will cause false read-ings. Move slowly; hurrying will onlycause you to miss targets.

Most good objects will respondwith a good repeatable signal.

If a signal does notrepeat after swingingthe coil directly over

the suspected target afew times, it is more

than likely trashmetal. False signals

can be caused bytrashy ground,

electricalinterference,

or by largeirregular

trash

objects. These signals are easilyrecognized by their often broken ornon-repeatable nature.

The Pioneer 202 is a very sensitiveand deep-seeking detector. It willrespond loudly to many targets thatother detectors would only detectwith a weak signal. Because ofthis, trash-induced signals andother sources of interference maycause signals that seem confusing.The key to managing these falsesignals is to dig only those targetsthat emit a strong repeatable signal.As you sweep the searchcoil backand forth over the ground, learnto recognize the difference be-tween the signals that occur atrandom and signals that arestable and repeatable.

When searching very trashyground, it is best to scan smallareas with slow, short overlappingsweeps. To prevent erratic signalsand difficult pinpointing in trashyareas, consider purchasing theBounty Hunter 4-Inch GoldNugget Coil System.

WHATREADSLIKE THIS

…MAYACTUALLYBE THIS

IN THE FIELD TECHNIQUES

16

METAL DETECTING APPLICATIONSCOINSHOOTING:

The most popular metal detecting application. When coinshooting, youwant to discriminate out pull tabs, screw caps, and iron objects. Bewarethat highly oxidized steel may also be detected.

Control settings required.1) Press DISC/ALL METAL touch pad.2) Turn the Disc/Notch Knob to the 3:00 position.

RELIC HUNTING:A relic is a historical object, sometimes of great value. Relics can be foundin abandoned homes, plowed fields or even your own backyard. Researchthe local library to learn of historical events or places in the area. You canthen target your search to a specific area and gain valuable insight into yourlocal history.

Control settings required.1) Press DISC/ALL METAL touchpad.2) Turn the DISC/NOTCH knob 100% counterclockwise.

Many relics are iron, so you do not want to discriminate.

CACHE HUNTING:A cache, pronounced “cash” is a buried or hidden valuable stored inside acase, strong box, or bag. A cache can be hidden in the floor or walls of ahouse, or buried nearby. Operate in the ALL METAL mode.

Control settings required.1) Press DISC/ALL METAL touchpad.2) Turn the DISC/NOTCH knob 100% counterclockwise.

JEWELRY HUNTING:Jewelry can be found wherever people congregate. Beaches, parks, schoolyards and fair grounds are all littered with lost jewelry. Your greatestchallenge is the interference from pull tabs and cans. You must use adiscrimination mode: AUTO NOTCH is best.

Control settings required.1) Press the AUTO NOTCH touchpad.2) Set Disc/Notch knob at 2:00. Dig only the repeatable low and hightones, avoid the broken or non-repeatable tones.

OTHER APPLICATIONS:Use your Pioneer 202 to find property markers, machine parts, and lostkeys. Keep your detector in ALL-METAL mode for these tasks.Gold prospecting also requires the ALL-METAL mode.

17

TROUBLESHOOTING

TROUBLE SHOOTING GUIDESYMPTOM CAUSE SOLUTION

Detector chatters • Using detector • Use detectoror beeps erratically indoors outdoors only

• Using detector near • Move away power lines from power lines

• Using 2 detectors in • Keep 2 detectorsclose proximity at least 30’ apart

• Highly oxidized • Only dig upburied object repeatable

signals• Environmental • Reduce sensitivity

electromagnetic until erratic interference signals cease

Constant low tone • Discharged batteries • Replace batteriesor constant repeating • Wrong type of • Use only 9V tones batteries alkaline batteries

LCD does not lock • Multiple targets • Move coil slowlyon to one target ID present at different anglesor detector emits • Highly oxidizedmultiple tones target

• Sensitivity set • Reduce sensitivitytoo high

No power, no • Dead batteries • Replace batteriessounds • Poor battery • Check connections

contact• Cord not connected

securely• Not moving • Sweep searchcoil

Searchcoil from side-to-side

CARE AND MAINTENANCEYour Pioneer 202 Metal Detector is an example of superior design and craftsmanship. The following suggestions will help you care for yourmetal detector so you can enjoy it for years to come.

Handle the metal detector carefully. Dropping it candamage circuit boards and cases.

Use and store the metal detector in normal temperatureenvironments. Temperature extremes can shorten thelife of electronic devices and distort or melt plastic parts.

Wipe the metal detector with a damp cloth occasionallyto keep it looking new. Do not use harsh chemicals,cleaning solvents, or strong detergents to clean themetal detector.

The coil is waterproof and may be submerged in either fresh or saltwater.Be careful to prevent water from entering the chassis. After using the coilin saltwater, rinse it with fresh water to prevent corrosion of the metalparts.

Modifying or tampering with the detector’s internal components cancause a malfunction and will invalidate your detector’s warranty.

TREASURE HUNTER’S CODE OF ETHICS:• Always check Federal, State, County and local laws before searching.• Respect private property and do not enter private property without the owner’s

permission.• Take care to refill all holes and leave no damage.• Remove and dispose of any and all trash and litter found.• Appreciate and protect our inheritance of natural resources, wildlife and private

property.• Act as an ambassador for the hobby, use thoughtfulness, consideration and

courtesy at all times.• Never destroy historical or archaeological treasures.• All treasure hunters may be judged by the example you set; always conduct yourself

with courtesy and consideration of others

First Texas Products, LLC1465-H Henry Brennan

El Paso, TX 79936(915) 633-8354

FIRST TEXAS PRODUCTS, LLC5-YEAR LIMITED WARRANTY

Copyright ©2012 by First Texas Products, L.L.C.

All rights reserved, including the right to reproduce this book, or parts thereof, in any form, except for theinclusion of brief quotations in a review.

Published by First Texas Products, L.L.C.Bounty Hunter® is a registered trademark of First Texas Products, L.L.C.

The BOUNTY HUNTER PIONEER series of metal detectors is not associated or connected in any way withPioneer Corporation or its PIONEER brand audio and video products or other products.

www.detecting.com

Bounty Hunter Metal Detectors are warranted against defects inworkmanship or materials under normal use for five years from

date of purchase to the original user. Liability in all events islimited to the purchase price paid. Liability under this Warranty islimited to replacing or repairing, at our option, any Bounty HunterDetector returned, shipping cost prepaid, to First Texas Products,LLC. Damage due to neglect, accidental damage or misuse of this

product is not covered by this warranty.Proof of purchase is required to make a claim under this warranty.

NOTE TO CUSTOMERS OUTSIDE THE U.S.A.This warranty may vary in other countries, check with your distributor for details.

Factory warranty follows the channel of distribution.Warranty does not cover shipping costs

According to FCC part 15.21 Changes or Modifications made to this device not expressly approved by the partyresponsible for compliance could void the users authority to operate this equipment.

19

ACCESSORIES

FOR COMPLETE DETAILS VISIT WWW.DETECTING.COM • 1-800-413-4131

Carry Bag Rugged double-stitched construction - CBAG-W

Pouch & Digger Combo Pouch with 2 large pockets & 9” heavy duty digging tool. TP-KIT-W

Bounty Hunter Stereo HeadphonesUse with Bounty Hunter metal detectors. Lightweight and adjustable withtrue stereo sound, adjustable volume, 1/8 jack with 1/4 adaptor,4’ cable. HEAD-W

Pin PointerPinpoints the exact location of buried metal objects. Audio signal indicator and vibrator. Runs on 1 – 9-Volt Battery. PIN POINTER-W

Sand ScoopLarge scoop with filtering holes. Made of strong plastic. SAND SCOOPBH

Replacement/Accessory Search Coils10” Magnum Coil – 10COIL8” Replacement Standard Coil – 8COIL-N4” Gold Nugget Coil – 4COIL

Coil CoversProtect your coil from abrasion and damage.10” Coil Cover – 10COVER8” Coil Cover – 8COVER-N4” Coil Cover – 4COVER

9” Heavy-Duty Digging ToolMetal blade with comfortable plastic handle and depth gauge TROWEL-2

Digging ToolLight and practical wide blade digging tool. TROWEL-W

Bounty Hunter T-Shirt 100% cotton with Bounty Hunter® Logo. Sizes – LG, XL & XXL

Bounty Hunter Baseball CapOne size fits all, with Bounty Hunter® logo.

GoldProspecting Kits

M202B Rev.2 092712