TOOLS REQUIRED FOR ASSEMBLY
No 2 & No 4 Phillips Head Screwdrivers
Electric Drill (Hammer Drill for Masonry Wall)
6.5mm Masonry Drill Bit (For Masonry Wall)
5mm Allen Key
Spirit Level
Adjustable Spanner
Hammer
Pliers
ASSEMBLY INSTRUCTIONS
NEW LINE WALL BEDWITH CABINET & WARDROBE
09.06.2020
NOTE:It is the installers responsibility to ensure safe work practices including (but not limited to) checking for and avoiding damage to electrical and plumbing services before fixing cabinets to wall.Construction Stages to be followed consecutively as per assembly instruction manual.Always ensure mechanism Stage 3 is carried out before Stage 4 and side cabinet assembly.For assembly and installation services refer to our website at www.pardo.com.au
Single Bed(SB)
Size (mm)
1054 x 471
1054 x 471
1054 x 217
2227 x 487
2227 x 487
1087 x 150
1054 x 487
2108 x 268
2227 x 507
910 x 370
910 x 270
PartsDescription
1 x Top
1 x Shelf
1 x Back
1 x Left End
1 x Right End
1 x Front Skirting
1 x Back
4 x Door Panels
2 x Side Panels
1 x Pillow Catch
1 x Head Board
1
2
3
4
5
6
7
8 - 11
12 - 13
14
15
Queen Bed(QB)
Size (mm)
1644 x 471
NA
1644 x 217
2227 x 487
2227 x 487
1677 x 150
1644 x 487
2108 x 415.5
2227 x 507
1500 x 370
1500 x 270
Double Bed(DB)
Size (mm)
1544 x 471
1544 x 471
1544 x 217
2227 x 487
2227 x 487
1577 x 150
1544 x 487
2108 x 390.5
2227 x 507
1400 x 370
1400 x 270
02
WALL BED CABINET COMPONENTS
1110
7
6
45
2
1
3
98
13
14
15
12
Hardware Description
? x Cam Bolts
24 x Cam Bolts(SB)
26 x Cam Bolts(DB)
22 x Cam Bolts(QB)
24 x Cam (SB)26 x Cam (DB)22 x Cam (QB)
8 x MountingPlate
2 x Handles& 4 x Screws
8 x 155 HingeFull Overlay
2 x MagneticCatch
10 x Green WallPlug
3 sets of 55mmmushroom head bolt,
2x washer & nut
8 x Butt Hinge8 x 65mm
Screws
8 x M6 Washer
8 x 50mmSocket Bolt
8 x FeralWashers
20 x ScrewCover Caps
12 x 28mmScrews
48 x 5mmVarianta Screws
6 x 4 Gauge5/8 Screws
03
STAGE 1 - WALL BED CABINET ASSEMBLY
PANEL DIAGRAM
Join to with cam fitting facing to rear
and tighten cams.
Join to and tighten cams.
7 Back
7 Back 4 Left End
4 Left End 4 Left End
6 Skirting
6 Skirting 4 Left End
Using hammer, tap cams into 20mm holes
in all panels where required.
Important: Ensure orientation of cam is as per photo above.
1
Screw cam bolts into 5mm holes in
locations corresponding to cam fittings.
2
Join to and tighten cams.NOTE: If you have purchased a Queen Bed Size disregard installation details of on following steps.
2 Shelf
3Back
2 Shelf3Back
3
2 Shelf
Lay on floor with cam bolts facing up and join
and to and tighten cams.3Back
3Back
2 Shelf
4 Left End
4
Left End4
Left End4
2 Shelf
03
STAGE 1 - WALL BED CABINET ASSEMBLY
1Top
3Back
2 Shelf
5 Right End
4 Left End
7 Back
6Skirting
65
Join to and tighten
cams.
7 Back 6 Skirting
2 Shelf
3Back
5 Right End
5 Right End 2-3 & 6-7
Join to and tighten cams.
Ensure is slid into location from shelf
side to ensure cam bolts slide into cam
fittings. (Dotted blue line indicates slide in
direction from front of unit and then pushed
up into location, refer to below image for
finished product)
3 - 5
5 Right End
1Top
7
8
04
STAGE 1 - WALL BED CABINET ASSEMBLY (CONTINUED)
1Top
3back
4 Left End
1Top
STAGE 1 COMPLETE Set aside remaining parts for use at later
stage.
05
STAGE 2 - FIXING WALL BED CABINET TO WALL
Lay cabinet face down with bottom facing the wall. Lift cabinet at top
pushing towards wall, being careful to have sufficient ceiling clearance.
4 Left End
Skirting Board
Cut skirting recess before pushingcabinet against the wall if required
Wall9
10
NOTE:As there is tension in the Wall Bed Mechanism when in the open position, it is very important that the cabinet is securely fixed to the wall.
(illustrated fixing points may vary due to wall stud locations)
3back
7 Back
NOTE: To ensure the cabinet sits neatly against the
wall when upright, it may be necessary to cut a
larger recess into the bottom left and right hand end
of cabinet to go over skirting.
Using a spirit level, find the correct vertical and
horizontal position. Mark this position on the wall
with a pencil, if location of install is out of level,
ensure you pack base of cabinet to level cabinet. If
unit is installed in a non level position, doors may not
align correctly.
Fastening Option 1 - Gyprock / Fibro / Timber WallsLocate wall studs and drill holes on and
to to align with wall studs.
Using 65mm screws fix and to wall.
Countersink screws on to avoid damage to
. Put on screw cover caps supplied
over 65mm screw fixings.
Fastening Option 2 - Brick / Masonry WallsPredrill holes (avoiding mortar joints) on and
and mark locations on wall to suit.
Move cabinet aside.
Using a 6.5mm masonry bit, drill 60mm deep holes into
the wall and insert green wall plugs supplied.
Move cabinet back into place against wall and fix
and to wall using 65mm screws.
Countersink screws on to avoid damage to
. Put on screw cover caps supplied
over 65mm screw fixings.
7 Back
3Back
7 Back
3Back
7 Back
14 Pillow Catch
7 Back
14 Pillow Catch
7 Back
3Back
7 Back3Back
06
MECHANISM COMPONENTS
Parts Description
Automatic Foot
Bed Frame
Connecting Rod
Spring Mechanism
Wall Mounting Brackets
Cradles
Mattress Guard
Extension Arm
16
17
18
19
20
21
22
23
16
17
18
19
20
21
2322
DETAIL VIEW
Hardware Description
12 x 40mm screw& masonry plug
Items not required in this install method
4 x 8 gauge5/8 screws
8 x 35mmmushroom head
& nut
4 x 55mmmushroom head bolt/
washer & nut
4 x 50mmsocket bolt
& nut/washer
Additional 50mmsocket screwsfound in Wall
Bed hardware set
MECHANISM DIAGRAM
07
STAGE 3 - DIY MECHANISM ASSEMBLY / INSTRUCTIONS
Split pin
Washer
Spring mechanism bracket
17 Bed Frame
20 Wall Mounting Bracket(Not required for thisinstall configuration)
19 Spring Mechanism
18 Connecting Rod
21 Front Cradle
23 Extension Arm 21 Back Cradle
Attach to , and (refer to page 2) using 50mm socket
bolt, nuts and washers provided with Wall Bed Cabinet Hardware pack (refer to page 2).
19 Spring Mechanism 21 Front/Back Cradle11 4 Left End 5 Right End
Bolt on (refer to page 7) to the top of through the predrilled holes and using 50mm socket
screw, nuts and bolts provided.
17 Bed Frame12 22 Mattress Guard(s)
Lower in between the and bolt through the predrilled holes to the spring mechanism
bracket using the 55mm mushroom head bolt, nut and washer. You might find that the will be a tight fit in
between the
17 Bed Frame14 19 Spring Mechanism
17 Bed Frame
19 Spring Mechanism
Remove the split pin and washer from the and attach the to the through the predrilled hole on
the and replace the washer and then the split pin. You might need to lower the slightly to
line up the and the 17 Bed Frame
15 23 Extension Arm 18 Connecting Rod
18 Connecting Rod
23 Extension Arm 18 Connecting Rod
Attach the red handle supplied to the (refer to page 7) using the screws already pre-fitted to the .
To avoid damage to the , be sure that the bed is lowered using the red handle. 16 16 Automatic Foot
18 Connecting Rod
16 Automatic Foot
WARNING:When operating the Wall Bed Mechanism the Bed Frame must be carefully lowered all the way to the floor and NOT left to drop freely. If the bed frame is lowered without the weight of a mattress it may spring back causing injury. Do not try to vary the tension of the spring mechanism as it is NOT adjustable.
Bolt on and (refer to page 2) to using 55mm mushroom head bolt, nut and washer provided with Wall Bed Cabinet Harware pack (refer to page 2)
13 14 Pillow Catch 15 Head Board
Refer to above Mechanism Diagram for following instructions (wall bed cabinet shown grey dotted)
17 Bed Frame
Attach butt hinges to door panel to inside face to form two sets of bi-fold doors using the 5mm varianta screws provided in the Wall Bed Cabinet Hardware set (refer to drawing A above).
Attach mounting plates with 5mm varianta screws provided in the Wall Bed Cabinet Hadware set (refer to drawing B above).
NOTE: Ensure that hinge is on inside of doors
Insert clip-on hinges into hinge holes on outside edges of door panels.
Attach doors to cabinet by clipping hinges onto mounting plates on cabinet end panels.
Adjust doors if necessary by screw adjustment where hinge meets hinge plate.
Attached handles to doors provided in the Wall Bed Cabinet Hardware set (refer to page 2)
17
18
19
20
21
22
HINGE DIAGRAM
Ensure butthinge knucklefaces towardsinternal cupboard
Inside Face
A
Attach Clip-on Hinges
DoorCabinetB
Outside Face
hinged to cabinet
10 Door Panel
Drawing showing Door adjustmentby screw on mounting plate
08
STAGE 4 - FIXING SIDE PANELS & DOORS
Refer to above Hinge Diagram for following instructions
09
WALL BED CARCASS DIMENSIONS - SINGLE
Side Elevation NTS
Plan NTS
Front Elevation NTS
Note.All based on 16mm board construction
2108
117
503
1086
1647
116
16105416
1086
Wal
l
Wall
10
WALL BED CARCASS DIMENSIONS - DOUBLE
Side Elevation NTS
Plan NTS
2108
1586
503
1586
1647
116
16155416
117
Front Elevation NTS
Wal
l
Wall
Note.All based on 16mm board construction
11
WALL BED CARCASS DIMENSIONS - QUEEN
Side Elevation NTS
Plan NTS
Front Elevation NTS
1677
2108
503
1676
1647
116
16164416
Wall
Wal
l
Note.All based on 16mm board construction
117
Parts Description
1 x Top
1x Back
1 x Left End
1 x Right End
1 x Skirting
1 x Fixed Centre Shelf
1 x Door
1 x Base
3 x Adjustable Shelving
2 x Wire Basket
2 x Runner Sets
1 x Hanger rail and connector set
12
RIGHT WARDROBE COMPONENTS
Hardware Description
Size (mm)
437 x 471
437 x 2093
487 x 2227
487 x 2227
470 x 150
437 x 470
464 x 2108
437 x 454
434 x 460
24
25
26
27
28
29
30
31
32
33
34
35
24
25
26 27
28
2930
31
32
32
32
35
33
3334
34
Note.Right hand Wardrobe shown above.
8 x 5mmVarianta Screws
(for hinges)
10 x ScrewCover Caps
1 x Handle &2 x Screws
? x Cam Bolts 4 x MountingPlate32 x Cam Bolts32 x Cam
4 x 4mmRunner Spacers
12 x AdjustableShelf Pins
4 x 9mmRunner Spacers
14 x 28mmscrews
6 x 6mmVarianta Screws
(for runners)4 x 110 Hinge
Full Overlay
PANEL DIAGRAM
13
STAGE 5 - RIGHT HAND WARDROBE ASSEMBLYNOTE: STAGE 5 ONLY REQUIRED IF PURCHASING CABINET WITH RIGHT WARDROBE
25Back
Using hammer, tap cams into 20mm
holes in all panels where required.
Important: Ensure orientation of cam is as per photo above.
23
Screw cam bolts into 5mm holes in
locations corresponding to cam fittings.
24
Lay on floor with cam bolts facing
up.
Join to , tighten cams.
Ensure cam fixings on are facing the
to the rear of the cabinet.25 Back
25
25 Back
27 Right End
25 Back
27 Right End
NOTE: Panel noted in light blue indicates panel found in Wall Bed Cabinet box (refer to page 2) 13Side Panel
30Door
27Right End
28Skirting 31Base 29 Fixed Centre Shelf24 Top
35Hanger Rail & Connector Set
26Left End
27 Right End
34 Runner Sets
14
STAGE 5 - RIGHT HAND WARDROBE ASSEMBLY (CONTINUED)
28
27 Right End
26 Left End
34 Runner Sets28 Skirting
Join to o and tighten cams.
Using 28mm screws thread on 4mm and 9mm
runner spacers (to create 13mm runner spacer)
and screw fix to .
On the reverse side using 8 gauge 5/8 screws
fix to .
NOTE: Ensure runner spacers are fixed into the
hinge side of the door. will not
extend past hinges if runner spacers are
installed into the incorrect side.
34 Runner Sets 27 Right End
26 Left End
29
27 Right End
26 Left End
35 Hanger Rail & Connector Set
Push in ends of
into predrilled hole locations on
and . There is a height adjustability
allowance, position to suit the user’s preference.
27 Right End
26 Left End
35 Hanger Rail & Connector Set
Join to and .
Ensure are slid into location from
direction indicated to ensure cam bolts and
fixings drop into place (dotted blue line
indicates slide in direction from front of unit
and then pushed down into location, solid
black line indicates finished panel install
locations). Tighten cams.
26 24, 29 & 31 25 Back 27 Right End
25 Back
24Top
27 Right End
29Fixed Centre Shelf
31Base
24, 29 & 31
Align with cam fixings on
. Tighten cams.27
25 Back 24Top
29Fixed Centre Shelf
31Base
26 Left End
26 Left End
24, 25, 29 & 31
28 Skirting 31Base
31Base34 Runner Sets
33 Wire Basket
15
STAGE 5 - RIGHT HAND WARDROBE ASSEMBLY (CONTINUED)
Using Varianta screws attach hinge mounting
plates to pre-drilled holes. You
may choose to lay the (refer to page
11) beside to find correct hole to
fix hinge mounting plate to.
30
Stand wardrobe upright and using 28mm screws fix
to assembled Wall Bed Cabinet . Put in screw
cover caps supplied into screw fixings.
NOTE: To ensure the cabinet sits neatly against the wall when
upright, it may be necessary to cut a larger recess into the
bottom left and right hand end of cabinet to go over skirting.
32
33
33 Wire Basket
Slide in into place.
27 Right End
26 Left EndAssembled Wall Bed(refer to stage 1 & 2)
33 Wire Basket
34
32 Adjustable Shelving
Push in adjustable shelf pins onto pre-
drilled holes as required and slide in
32 Adjustable Shelving
27 Right End
Screw fix to assembled Wall Bed with 28mm
screws provided. Put in screw cover caps supplied.
13 Side Panel
27 Right End
30 Door
27 Right End
hinge mounting plates
31
13 Side Panel
27 Right End
26 Left End
Parts Description
1 x Top
1x Back
1 x Left End
1 x Right End
1 x Skirting
1 x Fixed Centre Shelf
1 x Door
1 x Base
3 x Adjustable Shelving
2 x Wire Basket
2 x Runner Sets
1 x Hanger rail and connector set
16
LEFT WARDROBE COMPONENTS
Size (mm)
437 x 471
437 x 2093
487 x 2227
487 x 2227
470 x 150
437 x 470
464 x 2108
437 x 454
434 x 460
24
25
26
27
28
29
30
31
32
33
34
35
24
25
26 27
28
29
30
31
32
32
32
35
33
33
34
34
Note.Right hand Wardrobe shown above. Hardware Description
8 x 5mmVarianta Screws
(for hinges)
10 x ScrewCover Caps
1 x Handle &2 x Screws
? x Cam Bolts 4 x MountingPlate32 x Cam Bolts32 x Cam
4 x 4mmRunner Spacers
12 x AdjustableShelf Pins
4 x 9mmRunner Spacers
14 x 28mmscrews
6 x 6mmVarianta Screws
(for runners)4 x 110 Hinge
Full Overlay
PANEL DIAGRAM
17
STAGE 5 - LEFT HAND WARDROBE ASSEMBLYNOTE: STAGE 5 ONLY REQUIRED IF PURCHASING CABINET WITH LEFT WARDROBE
25Back
34 Runner Sets
Using hammer, tap cams into 20mm
holes in all panels where required.
Important: Ensure orientation of cam is as per photo above.
35
Screw cam bolts into 5mm holes in
locations corresponding to cam fittings.
36
25 Back
37
NOTE: Panel noted in light blue indicates panel found in Wall Bed Cabinet box (refer to page 2)
12Side Panel
30Door
27Right End
28 Skirting
31Base
29Fixed Centre Shelf
24Top 35 Hanger Rail & Connector Set
26Left End
26 Left End
Lay on floor with cam bolts facing
up.
Join to , tighten cams.
Ensure cam fixings on are facing the
to the rear of the cabinet.
25 Back
25 Back
26 Left End
26 Left End
18
STAGE 5 - LEFT HAND WARDROBE ASSEMBLY (CONTINUED)
4027 Right End
26 Left End
34 Runner Sets
28 Skirting
41
27 Right End
26 Left End
35 Hanger Rail & Connector Set
Join to and
Ensure are slid into location from
direction indicated to ensure cam bolts and
fixings drop into place (dotted blue line
indicates slide in direction from front of unit
and then pushed down into location, solid
black line indicates finished panel install
locations). Tighten cams.
38 24, 29 & 31 25 Back
25 Back
24Top29Fixed Centre Shelf
31Base
24, 29 & 31
26 Left End
Align with cam fixings on
. Tighten cams.39
25 Back
24Top
29Fixed Centre Shelf31 Base
24, 25, 29 & 31
27 Right End
27 Right End
31Base
26 Left End
Join to o and tighten cams.
Using 28mm screws thread on 4mm and 9mm
runner spacers (to create 13mm runner spacer)
and screw fix to .
On the reverse side using 8 gauge 5/8 screws
fix to .
NOTE: Ensure runner spacers are fixed into the
hinge side of the door. will not
extend past hinges if runner spacers are
installed into the incorrect side.
34 Runner Sets
27 Right End
26 Left End
Push in ends of
into predrilled hole locations on
and . There is a height adjustability
allowance, position to suit the user’s preference.
27 Right End
26 Left End
35 Hanger Rail & Connector Set
28 Skirting 31Base
34 Runner Sets
33 Wire Basket
19
STAGE 5 - LEFT HAND WARDROBE ASSEMBLY (CONTINUED)
Using Varianta screws attach hinge mounting
plates to pre-drilled holes. You
may choose to lay the (refer to page
11) beside to find correct hole to
fix hinge mounting plate to.
42
Stand wardrobe upright and using 28mm screws fix
to assembled Wall Bed Cabinet . Put in screw
cover caps supplied into screw fixings.
NOTE: To ensure the cabinet sits neatly against the wall when
upright, it may be necessary to cut a larger recess into the
bottom left and right hand end of cabinet to go over skirting.
44
45
33 Wire Basket
Slide in into place.33 Wire Basket
46
32 Adjustable Shelving
Push in adjustable shelf pins onto pre-
drilled holes as required and slide in
32 Adjustable Shelving
Screw fix to assembled Wall Bed with 28mm
screws provided. Put in screw cover caps supplied.
13 Side Panel
30 Door
hinge mounting plates
43
13 Side Panel
26 Left End
26 Left End
26 Left End
26 Left End
26 Left End
27 Right End
27 Right End
Assembled Wall Bed(refer to stage 1 & 2)
HINGE DIAGRAM
Attach Clip-onHinges
Insert clip-on hinges into hinge holes on outside edges of door panels.
Attach doors to cabinet by clipping hinges onto mounting plates on cabinet end panels.
Adjust doors if necessary by screw adjustment where hinge meets hinge plate.
Attached handle to door
47
48
49
50
Note: Above image shows Right Hand Wardrobe
20
STAGE 6 - FIXING DOOR
21
LEFT / RIGHT WARDROBE DIMENSIONS
16470
2108
117
16
486
503
16
470
487
Side Elevation NTS
Left CabinetPlan NTS
Left CabinetFront Elevation NTS
Note.All based on 16mm board construction
16 470
16
486
503
16
470
487
Right CabinetPlan NTS
Right CabinetFront Elevation NTS
Top Related