के� ��य मुहर �वभाग-2
हमारा संदभ�: सीएमडी-2/16:513 (भाग 1 एवं 2) 19 05 2017
�वषय: आई एस513 (भाग 1) :2016 के पुनर�*+त एस ट� आई और अतंरण 1दशा 3नद4श का काया��वयनऔर आई एस
513 (भाग 2):2016 के एस ट� आई और अंतरण 1दशा 3नद4श का काया��वयन
स�म �ा�धकार� �वारा अनुमो�दत आई एस 513 (भाग 1) :2016 के पुनर�%�त एस ट� आई और अंतरण �दशा +नद,श और
आई एस 513 (भाग 2):2016 के एस ट� आई और अंतरण �दशा +नद,श के त-काल काया01वयनहेतु संल3न है ।
सभी �े7ीय काया0लय8/शाखा काया0लय8स ेआ;ह है क< इसे अपने अ�धकार �े7 म> ि@थतसभी लाइसे1स धारक8/ आवे�क8 को
सू�चत करे और अनुपालन सु+निDचत करे ।
(अEण पुछकायला)
वैGा+नक-सी
5ी ए. के. भटनागर, वै9ा3नक – एफ और <मुख (सीएमडी-2)(ह>ता/-)
सभी �े7ीय/शाखा/ काया0लय8 को पIरचाJलत
�+तJलKप : आई ट� एस को बीआईएस इंMानेट पर अपलोड करने के Jलए
CENTRAL MARKS DEPARTMENT-2
Our Ref: CMD-2/16 513 (Pt 1 & Pt 2) 19 05 2017
Subject: Switchover guidelines for implementation of IS 513 (Part 1):2016 and guidelines for
implementation of IS 513 (Part 2):2016.
Please find enclosed switch over guidelines for implementation of IS 513 (Part 1):2016 and guidelines for
implementation of IS 513 (Part 2) 2016, duly approved by Competent Authority, for immediate
implementation.
ROs/BOs are requested to kindly bring to the notice of licensees/ applicants under their jurisdictions and
ensure compliance to implementation of the above guidelines.
(Arun Pucchakayala)
Scientist C
Shri A. K. Bhatnagar, Scientist – F & Head (CMD-2)(sd/-)
All ROs/BOs
Copy to : ITS for hosting on BIS Intranet.
CENTRAL MARKS DEPARTMENT -2
Our Ref: CMD-2/16: IS 513(pt.1) & (pt.2) 18-05-2017
Subject: Guidelines for switchover of licences held as per IS 513:2008 to IS 513 (Pt-1):2016
& for implementation of IS 513(Pt-2):2016
1. Indian Standard IS 513:2008 has been revised and published in two parts as
follows:
Old Standard Revised Standard
IS 513:2008, Cold Reduced Low Carbon
Steel Sheet and Strip
IS 513(Pt-1):2016, Cold Reduced
Carbon Steel Sheet and Strip Part 1
Cold Forming and Drawing Purpose
IS 513(Pt-2):2016, Cold Reduced
Carbon Steel Sheet and Strip Part 2
High tensile and multi-phase steel
2. In view of the above revision, the following new STIs have been issued:
Standard STI
IS 513(Pt-1):2016 Doc:STI/513 (Part 1)/11 April 2017
(Annex-1). This STI replaces
Doc:STI/513/10 September 2016 as per
IS 513:2008
IS 513 (Pt-2):2016 Doc:STI/513 (Part 2)/1 April 2017
(Annex-2)
3. In IS 513 (part1):2016,for cold forming and drawing applications, new grades along with
existing grades of IS 513:2008 have been introduced.
4. In IS 513 (part2):2016, for automobile and engineering applications, new grades of High
tensile and multi-phase steel sheet and strips have been introduced.
5. The modifications made in IS 513 (Part 1): 2016 and IS 513 (part-2): 2016 are listed at
Annex -3, for general guidance.
6. IS 513:2008 stands cancelled after 15th
December 2017 as per the gazette notification.
7. The existing licences as per IS 513:2008 have to be endorsed for changeover to
IS 513(Part 1): 2016, by 15th
December 2017.
8. For use of standard mark on grades covered under IS 513(Part 2): 2016, manufacturers
are required to submit application with fee for new licence.
9. In order to switchover from IS 513:2008 to IS 513 (part 1) & (part 2), following actions
need to be completed by the licensees at the latest by 01 December 2017:
i) Existing Licensees as per IS 513:2008 shall submit the following: a) acceptance to STI (Doc: STI/513 (Part 1)/ 11 April 2017), b) acceptance to Marking fee as per IS 513(pt-1):2016 (rates same as that of
IS 513:2008) c) CMD/PF 306 confirming availability of testing equipments as per
IS 513(pt-1):2016:
d) Evidence of conformity as indicated below for the designations covered in the scope of existing licence:
Designation in the
existing licence
Evidence of conformity (as per
IS 513(Pt.1) : 2016)
CR0 factory test report or test report from BIS recognized Lab
CR1 factory test report or test report from BIS recognized Lab, for any one temper designation
CR5 *Test report from BIS recognized lab (see note)
CR2,CR3,CR4 Not required
ii) For inclusion of other grades which are not covered in the scope of licence, requests for inclusion may be submitted to the BO.
iii) Switchover of Licences held as per IS 513:2008 to IS 513(part 1):2016 shall be complete by 15 December 2017.
10. For Switchover of Licences held as per IS 513:2008 to IS 513(part 1 & (part2) the
following actions are to be ensured by the BOs:
i. All BOs shall inform Applicants and Licensees under their jurisdiction about the revision of the Standard.
ii. BOs shall ensure that no licence as per IS 513:2008 is under operation after 15 December 2017.
iii. BO may issue endorsement in respect of the licence suitably on receipt of documents as mentioned above from the licensee, confirming implementation of the revised Standard.
iv. In case any licensee fails to complete all the above actions by 15th
December 2017, further necessary action as per OMPC 2004 (with all amendments) and guidelines on Stoppage and Resumption of Marking ref:CMD-1/2:1 dtd: 01 Dec 2016, shall be initiated by the concerned BO.
v. For all those grades as per IS 513(part 1):2016, which are not covered in the licence, inclusion of new varieties can be processed based on the request of the licensee as per the grouping guidelines (Annex-4) and as per the existing procedure of OMPC.
vi. Inform Licensees of IS 513:2008, interested in obtaining new licence for IS 513(part-2):2016, to submit application along with fee and the following:
a) undertaking on letter head that they can produce and test the product as per IS 513(part-2):2016 with the existing facilities already verified by BIS as per IS 513:2008
b) *Test report from BIS recognized lab (see Note and Annex-5)
c) Acceptance to STI as per IS 513(pt.2):2016 d) Acceptance to MF as per IS 513(pt.2):2016(will be notified shortly) e) payment of prescribed advance minimum marking fee f) Self evaluation-cum-verification report(Section-A only)
vii. Applications received as above shall be processed for grant of licence without
need for carrying out visit prior to grant of licence as the facilities were already verified at the time of GOL as per IS 513:2008. BOs shall make efforts for
arranging an early surveillance inspection during which detailed verification of the existing process and product can be made alongwith revalidation of the
manufacturing capabilities.
*Note: Till such time laboratories having test facilities as per IS 513(part-1):2016 / IS 513(part-2):2016 are recognized, test reports from BIS recognized laboratories, which are
recognized as per IS 513:2008, shall be accepted. If complete testing of the product is not possible in one lab, the product may be tested in any combination of laboratories (outside/in-
house).
11. In case of applications which are under process as per IS 513:2008, the following actions are
required to be taken by BOs:
i. On receipt of requests from applicants opting for considering their application as per the revised Standard IS 513(pt.1):2016, the application is to be processed as per
IS 513(pt.1):2016. In such cases the applicant shall be required to submit an undertaking that in no circumstances their application shall be considered as per IS
513:2008. ii. Applications recorded under normal procedure where samples are yet to be drawn
for independent testing shall be processed only as per the revised Standard IS 513 (part
1):2016. iii. Wherever the application is at final stage of GOL (i.e. TR received/sample drawn
and TR awaited), the licence shall be granted as per the version of standard indicated in test reports. However, such licensee shall be advised to complete actions for switch
over to the revised version of standard by 01 December 2017. iv. A declaration shall be obtained from all Applicants, for applications being processed
as per the old Standard that they will switch over to the revised Standard IS 513 (part 1):2016 by 01 December 2017.
12. Fresh applications shall be processed only as per the revised Standards IS 513 (part 1):2016 & IS 513 (part 2):2016.
13. Beyond 15 December 2017 no Licence shall be granted as per the old Standard IS 513:2008. 14. The above guidelines shall come into force with immediate effect
Encl: As above
(Arun Pucchakayala)
Scientist C,CMD-2
Head (CMD-2) (sd/-)
DDG(Cert.) (sd/-)
All ROs/BOs
Doc : STI/513(Pt.1)/ 11, April 2017
1
SCHEME OF TESTING AND INSPECTION FOR CERTIFICATION OF
COLD REDUCED CARBON STEEL SHEET AND STRIP
PART 1 COLD FORMING AND DRAWING PURPOSE
ACCORDING TO IS 513 (part 1):2016 (Sixth Revision) 1 LABORATORY - A laboratory shall be maintained which shall be suitably equipped and
staffed, where the tests shall be carried out in accordance with the methods given in the
specification. 1.1 All testing apparatus/measuring instruments shall be periodically checked, verified and
calibrated as appropriate and records of such checks/verification, calibration shall be
maintained.
1.2 Periodic calibration shall be done on the tensile testing machine. The frequency of
such calibration should preferably be once in six months, and in any case, not more
than once in a year.
2 TEST RECORDS - All records of tests as per this scheme of testing and inspection shall be
kept in suitable forms. 2.1 Copies of any records or charts that may be required by BIS shall be made available at any
time on request. 3. QUALITY CONTROL – It is recommended that, as far as possible, Statistical Quality
Control (SQC) methods may be used for controlling quality of the product during production as
envisaged in this scheme [See IS 397 (Part 1), IS 397 (Part 2) and IS 397 (Part 3)]. 3.1 In addition efforts should be made to gradually introduce the Quality Management
System in accordance with IS/ISO 9001. 4. STANDARD MARK - The Standard Mark, as given in Column (1) of the first schedule of the
licence, as specified for cold rolled carbon steel sheets and strips as per IS 513(part 1):2016 shall
be legibly marked on top of each package of sheets and strips. 4.1TEST CERTIFICATE – For each consignment of BIS Certified material conforming to IS
513(part 1):2016 there shall be a test certificate which shall contain the Standard Mark, the cast
number, Control Unit number, designation, grade and the corresponding test results (as given in
Annexure I).
4.2 MARKING – The following shall be legibly marked on the top of each bundle or package of
sheets and strips or shown on a tag attached to each coil :
a) Manufacturer’s name or trade mark,
b) Nomenclature of grade Quality
c) Product dimensions,
d) Cast or identification mark by which the sheet or strip may be traced to the cast or casts from
which they were made,
e) Mass/Net weight and
f) Date of manufacture
g) Licence No. (CM/L….)
Annex-1
Doc : STI/513(Pt.1)/ 11, April 2017
2
h) temper
i) surface finish designation
4.3 SUPPLY OF MATERIAL AND DELIVERY CONDITIONS - The material shall meet the
requirements of clause 4 and 13 of the specification. 4.3.1 PACKING - Each sheet shall be treated on both sides with non-hardening type
preventive oil which can be easily washed with aqueous alkali solution. The product may be
ordered “not oiled” if required [Ref. cl.9.6 of IS 513(part 1):2016].
4.3.2 Sheets and strips shall be supplied in bundles or packages not weighing more than 3
tonnes or as agreed to between the purchaser and the manufacturer.
4.3.3 Sheets and strips shall be securely packed in waterproof material and covered all over
with steel envelope and securely tied round with steel straps and preferably with wooden battens
underneath to prevent the sheets from rusting and damage during transit. 5. LEVELS OF CONTROL : Inspection and tests at various levels of control specified in
Table 1 shall be carried out on all quantities of steel intended to be covered under this scheme
and appropriate records as per para 2 and charts as per para 3 of this STI shall be maintained.
All production which conforms to the Indian Standard and covered by the licence shall be
marked with BIS Standard Mark. 5.1 METHOD OF MANUFACTURE – The method of manufacture of Steel for sheets and
strips shall be left at the discretion of the manufacturer.
5.2 CONTROL UNIT: For the purpose of this scheme, 50 tonnes of material or part thereof
representing the same cast, grade quality and heat-treatment (if any) rolled to same thickness and
processed in same condition shall constitute a control unit.
5.3 Sheets and strips shall be supplied rimmed, semi-killed or killed condition as agreed to
between the purchaser and the manufacturer. However, grades supplied in delayed ageing and
non-ageing guarantee shall be supplied only in fully aluminium killed or in a fully stabilized
condition.
5.4 On the basis of tests and inspection results, decision regarding conformity or otherwise of lots
of steel to the requirements of the specification shall be taken as indicated below: 5.5 CHEMICAL COMPOSITION - Chemical composition (Ladle analysis) obtained by
analyzing one sample from each heat shall conform to the requirements laid down in Table 3 of
the specification. Product analysis shall be carried out at the rate of one from every cast and the
permissible variation in the case of product analysis shall be as laid down in Table 4 of the
specification. The analysis of the steel shall be carried out according to IS 228 and its relevant
parts or any other established instrumental/chemical method. In case of dispute the procedure
given in IS 228 and its relevant parts shall be referee method. The manufacturer shall declare the
established instrumental method adopted for chemical analysis, details of the reference material
accompanied with test certificate used for its calibration and frequency of calibration.
Doc : STI/513(Pt.1)/ 11, April 2017
3
5.6 RETEST - If a test does not give the specified results, two additional tests shall be carried out
at random on the same lot. Both retests shall conform to the requirements of this standard,
otherwise, the control unit shall be rejected.
6. REJECTIONS - Records shall be maintained for a reasonable time from which information
relating to the rejection of material which does not conform to IS 513(part 1):2016 may be
obtained. Such rejected material shall not in any case be mixed up with that conforming to this
specification.
7 SAMPLES - The licensee shall supply, free of charge, the samples required in accordance with
Regulation of the Bureau of Indian Standards from his factory or godown. BIS may procure
samples from open market. 8.0 REPLACEMENT - Whenever a complaint is received soon after the goods with Standards
Mark have been purchased and used, and if there is adequate evidence that the goods have not
been misused, defective goods shall be replaced free of cost by the licensee in case the complaint
is proved to be genuine and the warranty period ( where applicable ) has not expired. The final
authority to judge conformity of the product to the Indian standards shall be with the Bureau. The
firm shall have own complaint investigation system as per IS/ISO 10002.
8.1 In the event of any damage caused by the goods bearing the Standard Mark, or claim
being filed by the consumers against BIS Standards Mark and not "conforming to" the relevant
Indian Standard, entire liability arising out of such non conforming product shall be of the
licensee and BIS shall not in any way be responsible in such cases.
9. STOP MARKING - The marking of the product shall be stopped under intimation to the
Bureau if, at any time, there is any difficulty in maintaining the conformity of their product to the
specification, or the testing equipment goes out of order or for any reason. The marking may be
resumed as soon as the defects are removed under intimation to BIS. The licensee shall
implement the provisions of self-stoppage of Marking as mentioned in BIS Act, Rules
and Regulations. 9.1 The marking of the product shall be stopped immediately if directed to do so by Bureau for
any reason. The marking may then be resumed only after permission by the Bureau. The
information regarding resumption of markings shall also be sent to the Bureau.
10 PRODUCTION DATA - The licensee shall send to BIS a statement of quantity produced,
marked and exported and the value thereof at the end of each operative year of the licence as per
the enclosed proforma which has to be authenticated by a Chartered Accountant.
Table 1…..
Doc : STI/513(Pt.1)/ 11, April 2017
4
IS 513(part 1):2016, COLD REDUCED CARBON STEEL SHEET AND STRIP
PART 1 COLD FORMING AND DRAWING PURPOSE
TABLEL 1 (LEVELS OF CONTROL),
(Para 5 of the Scheme of Testing and Inspection)
TEST DETAILS LEVELS OF CONTROL REMARKS
Cl Requirement Test Method No. of samples Lot size Frequency
Clause Reference
7 Chemical
Composition
IS 228 or any other established instr/ Chem. Method. Alternatively, the method specified in relevant ISO/IEC standard
may be used.
a) Ladle Analysis 7.1
7.2
Table 3
IS 513(part
1):2016
IS 228
One
Each Heat
Each Heat Applicable for primary steel
producers only
b) Product Analysis
7.3
Table 4
IS 513(part
1):2016
i) One
ii) One
i) Each Cast
ii) Each Cast
i) Each Cast
ii) Each
Cast
i) Applicable for primary
steel producers with steel
making and both hot & cold
rolling facilities
ii) In case of Re-rollers with
cold-rolling facilities, no
further testing is required if
the material obtained from
primary producers of steel is
ISI marked and received with
test certificate.
8 Mechanical and
Physical Properties
8.1 Tensile Test 8.1.1,
8.1.2,8.1.3 ,
8.1.4 & 8.1.5
Table 5A,5B,
5C
IS 513(part
1):2016
IS 1608
One 50 tonnes or less Each
Control
Unit
To be carried out only if
specified by the purchaser
8.2 Cupping Test 8.2
Fig.1
IS 513(part
1):2016
IS 10175
One -do- -do- Applicable for steel grades of
quality CR2, CR3, CR4
subject to mutual agreement
between purchaser and
manufacturer.
Doc : STI/513(Pt.1)/ 11, April 2017
5
8.3 Hardness Test 8.3
Table 6
IS 513(part
1):2016
IS 1586
One -do- -do- Applicable for steel grades of
quality CR0, CR1.
8.4 Bend Test 8.4.1,
8.4.2,8.4.3 &
8.4.4
Table 7
IS 513(part
1):2016
IS 1599
One -do- -do-
8.5 Plastic Strain Ratio 8.5.1
8.5.2
Table 5A,5B,
5C
IS 513(part
1):2016
IS 11999
One -do- -do-
8.6 Tensile strain hardening component
8.6.1
8.6.2
Table 5A,5B,
5C
IS 513(part
1):2016 IS 15756
One -do- -do-
8.7 Bake hardening Index
8.7
Annex B
Table 5B,5C
IS 513(part
1):2016
One -do- -do- Applicable only for steel
designation- Bake hardening
5. Non-ageing characteristics
5.1, 5.2& 5.3
Table 2
IS 513(part
1):2016
- - Each
Control
Unit
Applicable for steel grades of
CR2, CR3, delay ageing
quality and non-ageing
quality.
9
Surface condition 9.1,9.2,9.3,
9.4
IS 513(part
1):2016
As agreed between the purchaser and the supplier.
9.5 Surface Finish 9.5.1, 9.5.2
& 9.5.3
IS 513(part
1):2016
IS 15262
As agreed between the purchaser and the supplier.
10
Freedom from defects
10.1,10.2
&10.3
IS 513(part
1):2016
Adequate inspection to ensure each item to be free from
defects
11 Dimensions &
Tolerances
11.1,11.2 &
11.3
IS 513(part
1):2016
IS/ISO16162
Adequate inspection to ensure each item to be within the
limits of specification.
Doc : STI/513(Pt.1)/ 11, April 2017
6
4 Supply of material 4.1,4.2 &4.3 IS 513(part
1):2016
As agreed to between the purchaser and the supplier Records of mechanical
properties as agreed to
between purchaser and the
manufacturer as per cl.4.3
of ISS shall be maintained.
13.3 Packing 13.3
9.6
Table 9
IS 513(part
1):2016
Each Sheet/strip shall be treated on both sides with non-
hardening type rust preventive oil, which can be easily
washed with aqueous alkali solution.
i) Weight of sheets and
strips in bundles or
packages shall be as agreed
to between the purchaser
and the manufacturer.
ii) The product may not be
oiled, only if required by
the purchaser.
Doc : STI/513(Pt.1)/ 11, April 2017
7
ANNEXURE-I (Para 4.1 of the Scheme of Testing and Inspection)
XYZ IRON AND STEEL COMPANY
(Registered office Address and works address) TEST CERTIFICATE FOR COLD REDUCED CARBON STEEL SHEET AND STRIP PART 1 COLD FORMING AND DRAWING PURPOSE
TEST CERTIFICATE No.________________________________________________________________________________DATE_________ To M/s_____________________________________________________________________________________________________________
It is certified that the material described below fully conforms to IS 513(part 1):2016 Chemical composition and Mechanical
properties of the product, as tested in accordance with the Scheme of Testing and Inspection contained in the BIS Certification Marks
Licence No.CM/L_____________________ are as indicated below against each order No. etc.
(PLEASE REFER TO IS 513(part1):2016 FOR DETAILS OF SPECIFICATION REQUIREMENTS)
TEST RESULTS
Ord
er
No.
Di
me
nsi
ons
Cast
No. &
C.U.
No.
Nomen
clature
of steel
grade
quality
Quan
tity
(Ton
nes)
Chemical Analysis Erichsen
Cupping
Test
hardness
BH
index
+Mechanical Properties r n Non-
ageing
character
istics
Condition
& Finish
C
(%) Al
(%) **
Cu
(%)
S
(%)
P
(%)
N
(%)
Yield Stress
(N/mm2)
Tensile
Strength
(N/mm2)
Elongation
(%)
The material supplied conforms to the stipulated rolling tolerances. ** For Copper bearing quality + If specified by the purchaser Remarks:
SIGNATURE DESIGNATION FOR XYZ
IRON & STEEL COMPANY
(It is suggested that size A-4 paper (210X297) be used for this certificate)
BIS
STANDARD
MARK
DOC: STI/513(Pt.1)/11 April 2017
PROFORMA FOR OBTAINING PRODUCTION DETAILS
Period covered
Name of Licensee
Name of Articles (s) IS No.
Grade/Type/Size/Variety/Class/Rating
Brand/Trade/Name(s) of Product covered under BIS Certification Mark
Total production of the articles(s) licensed for certification marking
Total production of the article(s) conforming to Indian Standard
Production covered with BIS Certification Mark and its Value :
a) Quantity
Brand Name used on production covered under BIS Certification Mark
Calculation of marking fee on unit-rate basis; Marking Fee per unit
a) Unit
b) Quantity covered with BIS Certification Mark
c) Marking fee rounded off in whole rupees as obtained by applying unit rates given in (a) on quantity
given in (b)
Quantity not covered with BIS Certification Mark, if any.
Reasons for such non-coverage
Brand Name under which non-ISI goods were sold
Quantity exported with BIS Standard Mark and its value
Brand Name under which BIS Certified goods are exported
Authentication by Chartered Accountant
8
Doc : STI/513(Pt.2)/ 1, April 2017
1
SCHEME OF TESTING AND INSPECTION FOR CERTIFICATION OF
COLD REDUCED CARBON STEEL SHEET AND STRIP
PART 2 HIGH TENSILE AND MULTI-PHASE STEEL
ACCORDING TO IS 513 (part 2):2016 (Sixth Revision)
1 LABORATORY - A laboratory shall be maintained which shall be suitably equipped and
staffed, where the tests shall be carried out in accordance with the methods given in the
specification. 1.1 All testing apparatus/measuring instruments shall be periodically checked, verified and
calibrated as appropriate and records of such checks/verification, calibration shall be
maintained.
1.2 Periodic calibration shall be done on the tensile testing machine. The frequency of
such calibration should preferably be once in six months, and in any case, not more
than once in a year.
2 TEST RECORDS - All records of tests as per this scheme of testing and inspection shall be
kept in suitable forms. 2.1 Copies of any records or charts that may be required by BIS shall be made available at any
time on request. 3. QUALITY CONTROL – It is recommended that, as far as possible, Statistical Quality
Control (SQC) methods may be used for controlling the quality of the product during production
as envisaged in this scheme [See IS 397 (Part 1), IS 397 (Part 2) and IS 397 (Part 3)]. 3.1 In addition efforts should be made to gradually introduce the Quality Management
System in accordance with IS/ISO 9001. 4 STANDARD MARK - The Standard Mark, as given in Column (1) of the first schedule of the
licence, as specified for cold rolled carbon steel sheets and strips as per IS 513(part 2):2016 shall
be legibly marked on top of each package of sheets and strips. 4.1 TEST CERTIFICATE – For each consignment of BIS Certified material conforming to
IS 513(part 2):2016 there shall be a test certificate which shall contain the Standard Mark, the
cast number, Control Unit number, designation, grade and the corresponding test results (as given
in Annexure I). 4.2 MARKING – The following shall be legibly marked on the top of each bundle or
package of sheets and strips or shown on a tag attached to each coil : a) Manufacturer’s name or trade mark, b) Nomenclature of grade Quality c) Product dimensions,
Annex-2
Doc : STI/513(Pt.2)/ 1, April 2017
2
d) Cast or identification mark by which the sheet or strip may be traced to the cast or casts from
which they were made,
e) Mass/Net weight and
f) Date of manufacture
g) Licence No. (CM/L….)
h) surface finish designation
4.3 SUPPLY OF MATERIAL AND DELIVERY CONDITIONS - The material shall meet the
requirements of clause 4 and 12 of the specification. 4.3.1 PACKING - Each sheet shall be treated on both sides with non-hardening type
preventive oil which can be easily washed with aqueous alkali solution. The product may be
ordered “not oiled” if required [Ref. cl.8.6 of IS 513(part 2):2016].
4.3.2 Sheets and strips shall be supplied in bundles or packages not weighing more than 3
tonnes or as agreed to between the purchaser and the manufacturer.
4.3.3 Sheets and strips shall be securely packed in waterproof material and covered all over
with steel envelope and securely tied round with steel straps and preferably with wooden battens
underneath to prevent the sheets from rusting and damage during transit. 5. LEVELS OF CONTROL : Inspection and tests at various levels of control specified in
Table 1 shall be carried out on all quantities of steel intended to be covered under this scheme
and appropriate records as per para 2 and charts as per para 3 of this STI shall be maintained.
All production which conforms to the Indian Standard and covered by the licence shall be
marked with BIS Standard Mark.
5.1 METHOD OF MANUFACTURE – The method of manufacture of Steel for sheets and
strips shall be left at the discretion of the manufacturer.
5.2 CONTROL UNIT: For the purpose of this scheme, 50 tonnes of material or part thereof
representing the same cast, grade quality and heat-treatment (if any) rolled to same thickness and
processed in same condition shall constitute a control unit.
5.3 Sheets and strips shall be supplied rimmed, semi-killed or killed condition as agreed to
between the purchaser and the manufacturer. 5.4 On the basis of tests and inspection results, decision regarding conformity or otherwise of lots
of steel to the requirements of the specification shall be taken as indicated below: 5.5 CHEMICAL COMPOSITION - Chemical composition (Ladle analysis) obtained by
analyzing One sample from each heat shall conform to the requirements laid down in Table 2 of
the specification. Product analysis shall be carried out at the rate of one from every cast and the
permissible variation in the case of product analysis shall be as laid down in Table 3 of the
specification. The analysis of the steel shall be carried out according to IS 228 and its relevant
parts or any other established instrumental/chemical method. Alternatively, the method specified
Doc : STI/513(Pt.2)/ 1, April 2017
3
in relevant ISO standard may be used. In case of dispute the procedure given in IS 228 and its
relevant parts shall be referee method. The manufacturer shall declare the established
instrumental method adopted for chemical analysis, details of the reference material accompanied
with test certificate used for its calibration and frequency of calibration.
5.6 RETEST - If a test does not give the specified results, two additional tests shall be carried out
at random on the same lot. Both retests shall conform to the requirements of this standard,
otherwise, the control unit shall be rejected.
6. REJECTIONS - Records shall be maintained for a reasonable time from which information
relating to the rejection of material which does not conform to IS 513(part 2):2016 may be
obtained. Such rejected material shall not in any case be mixed up with that conforming to the
specification.
7 SAMPLES - The licensee shall supply, free of charge, the samples required in accordance with
Regulation of the Bureau of Indian Standards from his factory or godown. BIS may procure
samples from open market. 8.0 REPLACEMENT - Whenever a complaint is received soon after the goods with Standards
Mark have been purchased and used, and if there is adequate evidence that the goods have not
been misused, defective goods shall be replaced free of cost by the licensee in case the complaint
is proved to be genuine and the warranty period ( where applicable ) has not expired. The final
authority to judge conformity of the product to the Indian standards shall be with the Bureau. The
firm shall have own complaint investigation system as per IS/ISO 10002. 8.1 In the event of any damage caused by the goods bearing the Standard Mark, or claim
being filed by the consumers against BIS Standards Mark and not "conforming to" the relevant
Indian Standard, entire liability arising out of such non conforming product shall be of the
licensee and BIS shall not in any way be responsible in such cases. 9. STOP MARKING - The marking of the product shall be stopped under intimation to the
Bureau if, at any time, there is any difficulty in maintaining the conformity of their product to the
specification, or the testing equipment goes out of order or for any reason. The marking may be
resumed as soon as the defects are removed under intimation to BIS. The licensee shall
implement the provisions of self-stoppage of Marking as mentioned in BIS Act, Rules
and Regulations. 9.1 The marking of the product shall be stopped immediately if directed to do so by Bureau for
any reason. The marking may then be resumed only after permission by the Bureau. The
information regarding resumption of markings shall also be sent to the Bureau.
10 PRODUCTION DATA - The licensee shall send to BIS a statement of quantity produced,
marked and exported and the value thereof at the end of each operative year of the licence as per
the enclosed proforma which has to be authenticated by a Chartered Accountant.
Table 1.…..
Doc : STI/513(Pt.2)/ 1, April 2017
4
IS 513(part 2):2016, COLD REDUCED CARBON STEEL SHEET AND STRIP
PART 2 HIGH TENSILE AND MULTI-PHASE STEEL
TABLEL 1 (LEVELS OF CONTROL),
(Para 5 of the Scheme of Testing and Inspection)
TEST DETAILS LEVELS OF CONTROL REMARKS
Cl Requirement Test Method No. of samples Lot size Frequency
Clause Reference
6 Chemical
Composition
IS 228 or any other established instr/ Chem. Method. Alternatively, the method specified in relevant ISO/IEC standard
may be used.
a) Ladle Analysis 6.a
6.b
Table 2
IS 513(part
2):2016
IS 228
One
Each Heat Each Heat Applicable for primary steel
producers only
b) Product Analysis
6.c
Table 3
IS 513(part
2):2016
i) One
ii) One
i) Each Cast
ii) Each Cast
i)Each Cast
ii)Each
Cast
i) Applicable for primary
steel producers with steel
making and both hot & cold
rolling facilities
ii) In case of Re-rollers with
cold-rolling facilities only, no
further testing is required if
the material obtained from
primary producers of steel is
ISI marked and received with
test certificate.
7 Mechanical and
Physical Properties
7.1 Tensile Test 7.1.1,
7.1.2,7.1.3 ,
& 7.1.4
Table 4A,4B
IS 513(part
2):2016
IS 1608
One 50 tonnes or less Each
Control
Unit
To be carried out only if
specified by the purchaser
7.2 Bend Test 7.2.1,
7.2.2,7.2.3 &
7.2.4
Table 5
IS 513(part
2):2016
IS 1599
One -do- -do-
Doc : STI/513(Pt.2)/ 1, April 2017
5
7.3 Tensile strain hardening component
7.3.1
7.3.2
Table 4A,4B
IS 513(part
2):2016 IS 15756
One 50 tonnes or less Each
Control
Unit
8 Surface Finish
8.4 Surface Condition 8.4.1
8.4.2
8.4.3
8.4.4
8.4.5
IS 513(part
2):2016
Adequate inspection to ensure each item is supplied
either of the surface qualities A or B
8.5 Surface Finish 8.5.1
8.5.2
8.5.3
Table 6
IS 513(part
2):2016
One Each Sheet/strip Each
Sheet/strip
9
Freedom from defects
9.1,9.2 &9.3 IS 513(part
2):2016
Adequate inspection to ensure each item to be free from
defects
10 Dimensions &
Tolerances
10.1,10.2 &
10.3
IS 513(part
2):2016
IS/ISO16162
Adequate inspection to ensure each item to be within the
limits of specification.
12 Packing 12.3
8.6
Table 7
IS 513(part
2):2016
Each Sheet/strip shall be treated on both sides with non-
hardening type rust preventive oil, which can be easily
washed with aqueous alkali solution.
i) Weight of sheets and
strips in bundles or
packages shall be as agreed
to between the purchaser
and the manufacturer.
ii) The product may not be
oiled, only if required by
the purchaser.
Doc : STI/513(Pt.2)/ 1, April 2017
6
ANNEXURE-I (Para 4.1 of the Scheme of Testing and Inspection)
XYZ IRON AND STEEL COMPANY
(Registered office Address and works address) TEST CERTIFICATE FOR COLD REDUCED CARBON STEEL SHEET AND STRIP PART 2 HIGH TENSILE AND MULTI-PHASE STEEL
TEST CERTIFICATE No.________________________________________________________________________________DATE_________ To M/s_____________________________________________________________________________________________________________
It is certified that the material described below fully conforms to IS 513(part 2):2016 Chemical composition and Mechanical
properties of the product, as tested in accordance with the Scheme of Testing and Inspection contained in the BIS Certification Marks
Licence No.CM/L_____________________ are as indicated below against each order No. etc.
(PLEASE REFER TO IS 513(part2):2016 FOR DETAILS OF SPECIFICATION REQUIREMENTS)
TEST RESULTS
Order
No.
Dime
nsio
ns
Cast No.
& C.U.
No.
Nomencl
ature of
steel
grade
quality
Quanti
ty
(Tonn
es)
Chemical Analysis n +Surface
roughness
Surface
Condition &
Finish C
(%) S
(%)
P
(%)
N
(%)
Yield Stress
(N/mm2)
Tensile Strength
(N/mm2)
Elongation
(%)
The material supplied conforms to the stipulated rolling tolerances. + If required by the purchaser Remarks:
SIGNATURE DESIGNATION FOR XYZ
IRON & STEEL COMPANY
(It is suggested that size A-4 paper (210X297) be used for this certificate)
BIS
STANDARD
MARK
DOC: STI/513(Pt.2)/1 April 2017
PROFORMA FOR OBTAINING PRODUCTION DETAILS
Period covered
Name of Licensee
Name of Articles (s) IS No.
Grade/Type/Size/Variety/Class/Rating
Brand/Trade/Name(s) of Product covered under BIS Certification Mark
Total production of the articles(s) licensed for certification marking
Total production of the article(s) conforming to Indian Standard
Production covered with BIS Certification Mark and its Value :
a) Quantity
Brand Name used on production covered under BIS Certification Mark
Calculation of marking fee on unit-rate basis; Marking Fee per unit
a) Unit
b) Quantity covered with BIS Certification Mark
c) Marking fee rounded off in whole rupees as obtained by applying unit rates given in (a) on quantity
given in (b)
Quantity not covered with BIS Certification Mark, if any.
Reasons for such non-coverage
Brand Name under which non-ISI goods were sold
Quantity exported with BIS Standard Mark and its value
Brand Name under which BIS Certified goods are exported
Authentication by Chartered Accountant
7
Annex-3
Significant changes in IS 513 (Part 1):2016
clause Requirement
1 It covers sheets and strips up to 4.0 mm thick both in coil form and cut lengths
3.2 New designations and grades are added
Classification of grades has been added
4.3 New designations have been added in temper designations
5.3 Non-ageing characteristics have been modified
7&8 chemical composition, variation in product analysis and mechanical properties
are changed as per the new designations and grades;
9,10 &
11
mechanical and physical properties, surface finish, freedom from defects and
dimensions and tolerances have been modified.
Significant changes in IS 513 (Part 2):2016
clause Requirement
1 It covers sheets and strips up to 3.0 mm thick both in coil form and cut lengths
3.2 Classification of grades has been added
6 & 7 chemical composition, variation in product analysis and mechanical properties
are changed as per the new designations and grades;
8,9 &
10
mechanical and physical properties, surface finish, freedom from defects and
dimensions and tolerances have been modified.
CENTRAL MARKS DEPARTMENT-2
Our Ref.: CMD-II/16: 513(part 1) 18 05 2017
Subject: Grouping Guidelines for certification of Cold Reduced Carbon Steel Sheet and
Strip part 1 cold forming and drawing purpose as per IS 513 (part 1): 2016
Table 1 of IS 513(part 1):2016 specifies different steel Quality Designations and Grades of Steel
that may be produced as per IS 513(part 1): 2016. Clause 11 of IS 513(part 1): 2016 specifies the
Dimensions and Tolerances of the Sheets/Strips to be supplied as per IS 513(part 1): 2016.
Further, Cl.4.3 of IS 513(part 1): 2016 specifies the various Temper Conditions and Cl. 9.5 of IS
513(part 1): 2016 specifies the various Surface conditions of the Sheets/Strips to be supplied as
per IS 513(part 1): 2016.
1. In order to follow a uniform policy in the drawl of samples for independent testing for the
purpose of grant of license/ inclusion of additional varieties in the existing license, the
following procedure is to be followed:
Group Designation(Quality) Grade No of sample
1 Cold Rolled CR0 i) One sample of any size of the
Grade may be drawn.
2 General Purpose CR1,CR 2
CR3,CR4& CR5
i) One sample of any size of any
Grade may be drawn. If sample is
tested for grade of lower tensile
strength and higher drawability(r) &
stretch-ability(n),the recommendation
may include Grades with higher
tensile strength and lower
drawability(r) & stretch-ability(n)
also.
ii) For example, Sample of CR5
should be drawn to cover CR1 to
CR5.
3 Drawing Quality ISC260G,ISC270C,
ISC270D,ISC270E
ISC270F.
i) One sample of any size of any
Grade may be drawn. If sample is
tested for grade of higher minimum
tensile strength and higher
drawability(r) & stretch-ability(n),
then the recommendation may
include lower Grades also.
ii) For example, Sample of ISC270F
should be drawn to cover ISC260G to
ISC270F.
Annex-4
4 Interstitial Free-High
Strength steel
ISC340P,ISC370P
ISC390P,ISC440P
i) One sample of any size of any
Grade may be drawn. If sample is
tested for grade of higher minimum
tensile strength then the
recommendation may include lower
Grades also.
ii) For example, Sample of ISC440P
should be drawn to cover ISC340P to
ISC440P.
5 Bake Hardening ISC270B,ISC300B
ISC320B,ISC340B,
ISC360B,ISC390B
,ISC440B
i) One sample of any size of any
Grade may be drawn. If sample is
tested for grade of higher minimum
tensile strength then the
recommendation may include lower
Grades also.
ii) For example, Sample of ISC440B
should be drawn to cover ISC270B to
ISC440B.
6 Re-phosphorized ISC280R,ISC320R,
ISC360R,ISC400R
i) One sample of any size of any
Grade may be drawn. If sample is
tested for grade of higher minimum
tensile strength then the
recommendation may include lower
Grades also.
ii) For example, Sample of ISC400R
should be drawn to cover ISC280R to
ISC400R.
7 C,Mn Steel ISC340W,ISC370W
ISC390W,ISC440W
i) One sample of any size of any
Grade may be drawn. If sample is
tested for grade of higher minimum
tensile strength then the
recommendation may include lower
Grades also.
ii) For example, Sample of ISC440W
should be drawn to cover ISC340W
to ISC440W.
2. During preliminary inspection, before drawing samples for independent testing, it shall be
ensured by IO that tests for Dimensions and Tolerances as per cl.11 of IS 513(Pt.1):2016
shall be carried out at factory premises on the samples to be drawn for independent testing as
it is difficult to transport bulky samples to laboratory. In case of inclusion, factory test report
for Dimensions and Tolerances as per cl.11 of IS 513(Pt.1):2016 may be accepted and
conformity of the grades included to the same has to be verified during next surveillance
visit.
3. The sample tested may be any of the sizes (see Cl.11), Surface condition ( cl.9.5) and
Temper condition (see Cl.4.3) as mentioned in the specification. It is to be ensured that at
least one sample of bright finish is to be drawn/tested in case applicant/licensee has applied
for bright finish. If the sample passes, the licence/inclusion can be granted for all the sizes,
temper conditions and surface finishes (cl.9.5) mentioned in the specification and as applied
by the applicant/licensee, provided that the firm is having all necessary manufacturing and
testing facilities for manufacture and testing of all other sizes, Temper conditions and
surface finishes of sheets/strips proposed to be included in the licence.
4. The scope of licence shall clearly indicate grades, thickness range, maximum width, temper
condition (as applicable), and surface finish class based on Manufacturing/Testing facilities.
5. During the operation of licence, BO shall ensure that all the grades, sizes, temper conditions
and surface conditions of sheets/strips covered in the license are drawn for independent
testing on rotation over a period of time.
( Arun Pucchakayala)
Scientist-C,CMD-2
Head (CMD-2)(sd/-)
All ROs BOS
CENTRAL MARKS DEPARTMENT-2
Ref.: CMD-II/16: 513(part 2) 18 05 2017
Subject: Grouping Guidelines for certification of Cold Reduced Carbon Steel Sheet and
Strip part 2 High Tensile and Multi-phase steel as per IS 513 (part 2): 2016
Table 1 of IS 513(part 2):2016 specifies different steel Quality Designations and Grades of Steel
that may be produced as per IS 513(part 2): 2016. Clause 10 of IS 513(part 2): 2016 specifies the
Dimensions and Tolerances of the Sheets/Strips to be supplied as per IS 513(part 2): 2016.
Further, Cl.8.4 specifies Surface Conditions and Cl. 8.5 specifies various Surface finishes of the
Sheets/Strips to be supplied as per IS 513(part 2): 2016.
1. In order to follow a uniform policy in the drawl of samples for independent testing for the
purpose of grant of license/ inclusion of additional varieties in the existing license, the
following procedure is to be followed:
Group Designation(Quality) Grade No of sample
1 High Strength Low
Alloy
ISC310LA,ISC320LA
ISC350LA,ISC380LA
ISC410LA,ISC440LA
ISC470L,ISC510LA
ISC550L,ISC590LA
ISC600LA,ISC700LA
ISC860LA
i) One sample of any size of
any Grade may be drawn. If
sample of higher minimum
tensile strength is tested then
the recommendation may
include grades of lower
minimum tensile strength also.
ii) For example, to cover
ISC310LA to ISC860LA,
sample of ISC860LA should be
drawn for independent testing.
2 C, Mn Steel ISC490W,ISC540W
ISC590W i) One sample of any size of
any Grade may be drawn. If
sample of higher minimum
tensile strength is tested then
the recommendation may
include grades of lower
minimum tensile strength also.
ii) For example, Sample of
ISC590W should be drawn to
cover ISC490W to ISC590W.
Annex-5
3 Dual Phase steel ISC450Y ,ISC490Y
ISC540Y ,ISC590YL
ISC590Y,
ISC780Y,ISC980YL
,ISC980Y
,ISC1180Y
ISC1180YL
i) One sample of any size of
any Grade may be drawn. If
sample of higher minimum
tensile strength is tested then
the recommendation may
include grades of lower
minimum tensile strength also.
ii) For example, sample of any
of the grades ISC1180YL
should be drawn to cover
ISC450Yto ISC1180YL.
4 Dual Phase steel ISC590YH ,ISC780YH
ISC980YH,ISC1180YH
i) One sample of any size of
any Grade may be drawn. If
sample of higher minimum
tensile strength is tested then
the recommendation may
include grades of lower
minimum tensile strength also.
ii) For example, sample of any
of the grades ISC1180YH
should be drawn to cover
ISC590YHto ISC1180YH.
5 TRIP Steel ISC590T,ISC690T,
ISC780T i) One sample of any size of
any Grade may be drawn. If
sample of higher minimum
tensile strength is tested then
the recommendation may
include grades of lower
minimum tensile strength also.
ii) For example, Sample of
ISC780T should be drawn to
cover ISC590T to ISC780T
6 Complex Phase Steel ISC600C,ISC780C,ISC980C i) One sample of any size of
any Grade may be drawn. If
sample of higher minimum
tensile strength is tested then
the recommendation may
include grades of lower
minimum tensile strength also.
ii) For example, Sample of
ISC980C should be drawn to
cover ISC600C to ISC980C.
7 Martensitic Steel ISC900M,ISC1100M,
ISC1300M, ISC1500M i) One sample of any size of
any Grade may be drawn. If
sample higher minimum tensile
strength is tested then the
recommendation may include
grades of lower minimum
tensile strength also.
ii) For example, Sample of
ISC1500M should be drawn to
cover ISC1500M to ISC900M.
8 Hot forming grades ISC480HF i) One sample of any size may
be drawn to cover all sizes in
the grade.
2. During preliminary inspection, before drawing samples for independent testing, it shall be
ensured by IO that tests for Dimensions and Tolerances as per cl.10 of IS 513(Pt.2):2016
shall be carried out at factory premises on the samples to be drawn for independent testing as
it is difficult to transport bulky samples to laboratory. In case of inclusion, factory test report
for Dimensions and Tolerances as per cl.10 of IS 513(Pt.2):2016 may be accepted and
conformity of the grades included to the same has to be verified during next surveillance
visit.
3. The sample tested may be any of the sizes (see Cl.10) and Surface condition (see Cl.8.4) as
mentioned in the specification. It is to be ensured that at least one sample of bright finish is
to be drawn/tested in case applicant/licensee has applied for bright finish. If the sample
passes, the licence can be granted for all the sizes and surface finishes (cl.8.5) mentioned in
the specification and as applied by the applicant/licensee, provided that the firm is having all
necessary manufacturing and testing facilities for manufacture and testing of all other sizes
and surface finishes of sheets/strips proposed to be included in the licence.
4. The scope of licence shall clearly indicate grades, thickness range, maximum width, and
surface finish class based on Manufacturing/Testing facilities.
5. During the operation of licence, BO shall ensure that all the grades and sizes of sheets/strips
covered in the license are drawn for independent testing on rotation over a period of time.
( Arun Pucchakayala)
Scientist-C,CMD-2
Head (CMD-2)(sd/-)
All ROs BOS
Top Related