INSTALLATION INSTRUCTIONS FOR PART 95-7951
95-7951
APPLICATIONSCHEVROLET
Aveo 2004-2006SUZUKI
Forenza 2004-2007Reno 2005-2007
Verona 2004-2007
KIT FEATURES• Double DIN Radio Provision• Stacked ISO Mount Units Provision
A) Double DIN Trim Plate • B) Double DIN Brackets
KIT COMPONENTS
A
TOOLS REQUIRED:Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
Dash Disassembly- Chevrolet Aveo 2004-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1- Suzuki Forenza 2004-2007 / Suzuki Reno 2005-2007. . . . . . . 2- Suzuki Verona 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Kit Assembly- Double DIN Mount Radio Provision . . . .. . . . . . . . . . . . . . . . . . . . . . . . 4- Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TABLE OF CONTENTS
95-7951
*Note: Refer also to the instructions included with the aftermarket radio.
95-7951 DASH DISASSEMBLY
CHEVROLET AVEO 2004-2006A
B
1
1
Remove (4) Phillips screws securingthe radio. Unplug and remove radio.(Figure B)
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Unclip and remove the trim panelsfrom both sides of radio/climate con-trols. (Figure A)
2
Continue to kit assembly.
95-7951 DASH DISASSEMBLY
SUZUKI FORENZA 2004-2007SUZUKI RENO 2005-2007
2
1
Open glove box and remove (5)Phillips screws ((3) on top and (2) onbottom) then remove entire glove box.
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Disconnect air selector cable on dri-ver’s side of center console behinddash above accelerator pedal. (Figure A & B)
2
4
Remove (4) 10 MM bolts securingradio. Unplug and remove radio.(Figure E)
Disconnect temperature selectorcable on passenger side of centerconsole behind glove box. (Figure C)
6
Unsnap and remove entire panel sur-rounding radio. NOTE: The clips hold-ing radio panel to dash are verystrong. (Figure D)
5
Continue to kit assembly.
A
B
Inside of Glove Box
C
E
AM/FM
TAPE
CDTUNE
1 2 3
4 5 6
BASS
MUTE
EQ
AST
SCAN
D
95-7951 DASH DISASSEMBLY
SUZUKI VERONA 2004-2007A
B
3
1
Remove (4) Phillips screws fromradio. Unplug and remove radio.(Figure B)
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
3
Unclip and remove the trim panel sur-rounding the radio. (Figure A)
2
Continue to kit assembly.
95-7951 KIT ASSEMBLY
4
DOUBLE DIN MOUNT RADIO PROVISION
CUTHEREON BOTH SIDES
D
B
A
C
E F
Snap the Double DIN brackets to theoutside edge of the Double DIN trimplate. (Figure E)
1
NOTE: For the Chevrolet Aveo 2004-06 and Suzuki Verona 2004-07, cutand remove front lower mounting tabsfrom the Double DIN trim plate (FigureA). For the Suzuki Forenza 2004-07 andthe Suzuki Reno 2005-07, cut the rearlower mounting tabs (Figure B).
NOTE: The Verona 2004-2007 subdash will need to be trimmed slightlyfor proper fit. Refer to illustration.(Figure C,D)
Slide the Double DIN radio into thebracket/trim plate assembly andsecure the radio to the assemblyusing the screws supplied with theradio. (Figure F)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
95-7951 KIT ASSEMBLY
5
STACKED ISO MOUNT UNITS PROVISION*Note: Refer also to the instructions included with the aftermarket radio.
E F
Snap the Double DIN brackets to theoutside edge of the Double DIN trimplate. (Figure E)
1
Slide the stacked ISO units into thebracket/trim plate assembly and securethe units to the assembly using thescrews supplied with the units.e(Figure F)
2
Continue to final assembly.
NOTE: The Verona 2004-2007 sub dashwill need to be trimmed slightly forproper fit. Refer to illustration. (Figure C,D)
CUTHEREON BOTH SIDES
DC
B
ANOTE: For the Chevrolet Aveo 2004-06 and Suzuki Verona 2004-07, cutand remove front lower mounting tabsfrom the Double DIN trim plate (FigureA). For the Suzuki Forenza 2004-07 andthe Suzuki Reno 2005-07, cut the rearlower mounting tabs (Figure B).
95-7951 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
6
Top Related