SELECTION GUIDE 9000 SERIES ACCELEROMETERS
GENERAL PURPOSE HIGH FREQUENCY LOW FREQUENCY ULTRA LOW FREQUENCY SPECIALTY
i
Table of Contents
Table of Contents
General Purpose Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
High Frequency Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Low Frequency Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
High Temperature Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specialty Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4-20mA Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Intrinsically Safe Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Accessories and Technical Information . . . . . . . . . . . . . . . . . . . . . . . . 23
Cables for Portable Instruments - Enpac and dataPAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Cable for Permanent Installations - XM and Enwatch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Switch Boxes, Switch Panels, and Terminal Boxes . . . . . . . . . . . . 24Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Typical Vibration Measurement Systems . . . . . . . . . . . . . . . . . . . . 27
Table of Contents ii
1
General Purpose Sensors
• Top or side exit connector versions
• Hermetically sealed construction
• Interface directly with vibration data collectors
• Ideal for FFT analysis of vibration frequencies
• Measurements for machinery diagnostics
• Low profile designs
General purpose, industrial accelerometers are recommended for permanent installation onto machinery and/or route-based vibration data collection to satisfy vibration trending requirements in Predictive Maintenance and Condition Monitoring applications.
2 General Purpose Sensors
General Purpose Sensors
9000A 9000B 9008 9010
Model Name General Purpose AccelerometerIntegral Cable General Purpose Accelerometer
Low Cost Integral Cable Accelerometer General Purpose Accelerometer
Part Number EK-43781I EK-43782I EK-46255I EK-45890I
Data Sheet Number GMSI10-TD001A-EN-E GMSI10-TD002A-EN-E GMSI10-TD032A-EN-E GMSI10-TD031A-EN-E
Dynamic
Sensitivity
English 100 mV/g 50 mV/g
SI 10.2 mV/(m/s2) 5.1 mV/(m/s2)
Accuracy +/- 5% +/- 20% +/- 10%
Measurement Range
English +/- 50 g 100 g
SI +/- 490 m/s2 +/- 981 m/s2
Frequency Response
+/- 5% 1.2 - 5,000 Hz 1.2 - 7,000 Hz - 1.2 - 5,000 Hz
+/- 10% 0.87 - 8,000 Hz - 0.85 - 7,000 Hz
+/- 3 dB 0.43 - 10,000 Hz 0.44 - 13,000 Hz 0.5 - 10,000 Hz 0.4 - 10,000 Hz
Resonance Frequency 28 kHz 22 kHz 30 kHz
Broadband Resolution (1 - 10,000 Hz)
English 300 μg 75 μg 350 μg 400 μg
SI 2943 μm/s2 735.6 μm/s2 3434 μm/s2 3924 μm/s2
Transverse Sensitivity ≤ 5% ≤ 7% ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC
Bias Output Voltage, nominal 8 - 12 VDC
Grounding case isolated
Settling Time ≤ 2.0sec
Environmental
Temperature Range -54 to 121°C
Shock Limit 5,000 g peak
Physical
Weight 61.7 gm 48.6 gm 99.3 gm 52 gm
Case Material stainless steel
Mounting 1/4 - 28 Female
Output Connector / Cabling MIL-C-5015/Top, 2 pin Integral cable, two-conductor shielded, polyurethane jacket, 10ft. MIL-C-5015/Top, 2 pin
Height 1.96 inch (49.8 mm) 2.96 inch (75.2 mm) 2.5 inch (64 mm) 1.97 inch (50 mm)
Diameter 11/16 inch (17.5 mm) 9/16 inch (14.3 mm) 11/16 inch (17.5 mm)
Certifications CE
Comments • Best choice for Portable• Good choice for Online• Additional RFI protection
• Integral 10ft Cable• Online
• Low Cost• Small Size• Integral 10ft Cable• Run in Conduit• Online
• Portable or Online
General Purpose Sensors 3
General Purpose Sensors
9100 9200 9300 9400
Model Name General Purpose Accelerometer General Purpose Accelerometer Low Cost General Purpose Low Cost Low Profile General Purpose
Part Number EK-43784I EK-47086I EK-43792I EK-47090I
Data Sheet Number GMSI10-TD004A-EN-E GMSI10-TD036A-EN-E GMSI10-TD010A-EN-E GMSI10-TD037A-EN-E
Dynamic
Sensitivity
English 100 mV/g
SI 10.2 mV/(m/s2)
Accuracy +/- 5% +/- 15 %
Measurement Range
English +/-50 g
SI +/- 490 m/s2
Frequency Response
+/- 5% 0.58 - 4,000 Hz 0.5 - 6,500 Hz 1.2 - 5,000 Hz 0.5 - 6,500 Hz
+/- 10% 0.42 - 5,000 Hz 0.4 - 7,500 Hz 0.87 - 8,000 Hz 0.4 - 7,500 Hz
+/- 3 dB 0.2 - 10,000 Hz 0.2 - 10,500 Hz 0.43 - 10,000 Hz 0.2 - 10,500 Hz
Resonance Frequency 20 kHz 25 kHz 28 kHz 25 kHz
Broadband Resolution (1 - 10,000 Hz)
English 50 μg 300 μg 50 μg
SI 490 μm/s2 2943 μm/s2 490 μm/s2
Transverse Sensitivity ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC
Bias Output Voltage, nominal 8 - 12 VDC
Grounding case isolated
Settling Time ≤ 5.0sec ≤ 8.0sec ≤ 2.0sec ≤ 8.0sec
Environmental
Temperature Range -54 to 121°C
Shock Limit 5,000 g peak
Physical
Weight 93 gm 145 gm 48.6 gm 145 gm
Case Material stainless steel
Mounting 1/4 - 28 Female 1/4 - 28 Male 1/4 - 28 Female 1/4 - 28 Male
Output Connector / Cabling MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 pin MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 pin
Height 2.06 inch (52.3 mm) 1.13 inch (28.7 mm) 1.66 inch (42.2 mm) 1.13 inch (28.7 mm)
Diameter 7/8 inch (22.2 mm) 1.38 inch (35.1 mm) 11/16 inch (17.5 mm) 1.36 inch (35.1 mm)
Certifications CE
Comments • Best choice for Online• Good choice for Portable• Additional RFI protection
• Best choice for Online• Good choice for Portable• Additional RFI protection• Low Profile• Recommended in mounting
applications with limited head room or where a more rugged mounting is required.
• Low Cost• Small Size• +/- 15% Sensitivity• Online
• Low Cost• +/- 15% Sensitivity• Online
4 General Purpose Sensors
5
High Frequency Sensors
• Gear mesh studies and diagnostics
• Bearing monitoring
• Small mechanisms
• High-speed spindles
• Vibration measurements on high speed rotating machinery
Successful vibration measurements begin with sensors that have adequate capabilities for the requirement. If the sensor’s frequency response characteristics are inadequate, the user risks corrupted or insufficient data to achieve a proper analysis and diagnosis. For vibration monitoring, testing, and frequency analysis of high-speed rotating machinery, spindles, and gear mesh, it is imperative to utilize a sensor with a sufficient high frequency range to accurately capture the vibration signals within the bandwidth of interest.
These precision, high frequency accelerometers meet the requirements of high frequency signal analysis. Miniature sized units are suitable for vibration measurements on small mechanisms where sensor size and weight become important factors.
6 High Frequency Sensors
High Frequency Sensors
9700A 9700B
Model NameHigh Frequency Miniature Accelerometer
High Frequency Miniature Accelerometer
Part Number EK-43799I EK-43800I
Data Sheet Number GMSI10-TD016A-EN-E GMSI10-TD017A-EN-E
Dynamic
Sensitivity
English 10 mV/g 100 mV/g
SI 1.02 mV/(m/s2) 10.2 mV/(m/s2)
Accuracy +/- 10 % +/- 5 %
Acceleration Range
English +/- 500 g +/- 50 g
SI +/- 4905 m/s2 +/- 490 m/s2
Frequency Response
+/- 5% - 2.4 - 10,000 Hz
+/- 10% 3.4 - 18,000 Hz 1.7 - 15,000 Hz
+/- 3 dB 1.6 - 30,000 Hz 0.8 - 20,000 Hz
Resonance Frequency 85 kHz 35 kHz
Broadband Resolution (1 - 10,000 Hz)
English 1.2 mg rms 100 μg
SI 1176 μm/s2 981 μm/s2
Transverse Sensitivity ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC
Bias Output Voltage, nominal 8 - 12 VDC
Grounding not isolated base isolated
Settling Time ≤ 3.0sec ≤ 5.0sec
Environmental
Temperature Range -54 to 121°C
Shock Limit 10,000 g peak 5,000 g peak
Physical
Weight 2.8 gm 30 gm
Case Material titanium stainless steel
Mounting 5-40 Male 10-32 Female
Output Connector / Cabling 5-44 Coaxial/Top 10-32 Coaxial/Side
Height 0.66 inch (16.8 mm) 1.03 inch (26.2 mm)
Diameter 3/8 inch (9.53 mm) 11/16 inch (17.5 mm)
Certifications
Comments • Low Cost• Small Size• Recommended for use in
vibration monitoring of machines where high frequency response and acceleration range is required, such as turbines, centrifugal and sliding vane compressors, turbochargers, etc.
• Portable or Online
• Online
7
Low Frequency Sensors
• Vibration measurements on slow rotating machinery
• Paper machine rolls
• Large fans and air handling equipment
• Cooling towers
• Buildings, bridges, foundations, and floors
Low-amplitude, vibration levels go hand-in-hand with low-frequency vibration measurements. For this reason, accelerometers are offered combining extended low frequency response with high output sensitivity in order to obtain the desired resolution characteristics and strong output signal levels, necessary for conducting low-frequency, vibration measurements and analysis.
All of these low-frequency industrial accelerometers benefit from some advantages including: rugged, laser-welded, stainless steel housing with the ability to endure dirty, wet, or harsh environments; hermetically sealed military connector or sealed integral cable; and a low noise, low impedance, voltage output signal with long-distance, signal transmission capability.
8 Low Frequency Sensors
Low Frequency Sensors
9100L 9200L 9500HLF 9600
Model Name Low Frequency Accelerometer Low Frequency AccelerometerLow Frequency Accelerometer (Low Bias Voltage)
Ultra Low Frequency Accelerometer
Part Number EK-43794I EK-43795I EK-43797I EK-43798I
Data Sheet Number GMSI10-TD011A-EN-E GMSI10-TD012A-EN-E GMSI10-TD014A-EN-E GMSI10-TD015A-EN-E
Dynamic
Sensitivity
English 500 mV/g 1,000 mV/g 10 V/g
SI 51 mV/(m/s2) 102 mV/(m/s2) 1.02 mV/(m/s2)
Accuracy +/- 5 %
Measurement Range
English +/- 10 g +/-5 g +/- 0.5 g
SI +/- 98 m/s2 +/- 49 m/s2 +/- 4.9 m/s2
Frequency Response
+/- 5% 0.5 - 2,000 Hz 0.1 - 200 Hz
+/- 10% 0.3 - 4,000 Hz 0.37 - 4,000 Hz 0.3 - 4,000 Hz 0.07 - 300 Hz
+/- 3 dB 0.2 - 6,000 Hz 0.04 - 500 Hz
Resonance Frequency 12 kHz 1 kHz
Broadband Resolution (1 - 10,000 Hz)
English 15 μg 10 μg 0.5 μg
SI 147 μm/s2 98 μm/s2 5 μm/s2
Transverse Sensitivity ≤ 7% ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC 24 - 28 VDC
Bias Output Voltage, nominal 8 - 12 VDC 8 - 12 VDC
Grounding case isolated
Settling Time ≤ 5.0sec ≤ 4.5sec ≤ 10.0sec ≤ 5.0min
Environmental
Temperature Range -54 to 121°C -18 to 65°C
Shock Limit 2,500 g peak 40 g
Physical
Weight 210 gm 173 gm 210 gm 624 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male 1/4 - 28 UNF Female
Output Connector / Cabling MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 pin MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 pin
Height 2-3/16 inch (55.6 mm) 1.13 inch (28.7 mm) 2.21 inch (56.1 mm) 2.8 inch (71.1 mm)
Diameter 1-3/16 inch (30.2 mm) 1.36 inch (34.5 mm) 1-3/16 inch (30.2 mm) 2-1/4 inch (57.2 mm)
Certifications CE
Comments •Portable or Online • Online
9
High Temperature Sensors
• Paper machine dryer sections
• Steel mills
• Hot conveyor systems
• Reactors and digesters
• Petrochemical pumps
• Food processing equipment
It is often necessary to monitor the vibration levels of rotating machinery operating at elevated temperatures or in high temperature environments. Such circumstances place extreme demands on vibration sensors and require the use of accelerometers with special design characteristics that extend their useable temperature range beyond that of other conventional units.
A variety of industrial high temperature accelerometers have a useable temperature range up to 325°F (163°C). The circuitry within these sensors has been specifically designed and tested to reliably withstand elevated temperature extremes. A slight trade-off with this redesigned circuitry is it will compromise the frequency response characteristics of the sensor. These accelerometers will operate in the same manner, with the same cabling, data collection, and signal conditioning equipment, as the general purpose accelerometers.
For extreme, high-temperature requirements, charge-mode accelerometers are recommended. Designed to withstand temperatures up to 500°F (260°C), charge-mode accelerometers do not contain internal signal conditioning circuits which impose temperature limits on general purpose accelerometers. However, since there is no signal conditioning circuits within charge-mode accelerometers, alternative cabling and signal conditioning equipment is required.
IMPORTANT Speciality sensors for high temperature gas turbines and other applications are available upon request, please contact your nearest Rockwell Automation office or contact the High Tech Inside Sales Team at (740) 548-5733
10 High Temperature Sensors
High Temperature Sensors
9100T 9200T 9150HT 9150HTA
Model Name High Temperature AccelerometerHigh Temperature Low Profile Accelerometer
High Temperature Charge-mode Accelerometer System
High Temperature Accelerometer with Armor Cable
Part Number EK-43805I EK-43806I EK-43807I EK-46496
Data Sheet Number GMSI10-TD020A-EN-E GMSI10-TD021A-EN-E GMSI10-TD022A-EN-E GMSI10-TD034A-EN-E
Dynamic
Sensitivity
English 100 mV/g
SI 10.2 mV/(m/s2)
Accuracy +/- 5 % +/- 15 %
Measurement Range
English +/- 50 g +/- 25 g
SI +/- 490 m/s2 +/- 245 m/s2
Frequency Response
+/- 5% 0.58 - 4,000 Hz 0.5 - 4,000 Hz - -
+/- 10% 0.42 - 5,000 Hz 0.37 - 6,000 Hz 1.67 - 3,000 Hz
+/- 3 dB 0.2 - 10,000 Hz 1 - 7,000 Hz
Resonance Frequency 20 kHz 23 kHz 30 kHz
Broadband Resolution (1 - 10,000 Hz)
English 150 μg 200 μg 120 μg
SI 1472 μm/s2 1962 μm/s2 1.18 μm/s2
Transverse Sensitivity ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC
Bias Output Voltage, nominal 8 - 14 VDC 11 - 14 VDC 8 - 12 VDC
Grounding case isolated base isolated
Settling Time ≤ 5.0sec ≤ 8.0sec ≤ 15.0sec (@ 70°F)
≤ 4.0min (@ 500°F)
Environmental
Temperature Range -54 to 163°C -54 to 260°C
Shock Limit 5,000 g peak 2,000 g peak
Physical
Weight 93 gm 145 gm 83.6 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male 1/4 - 28 UNF Female
Output Connector / Cabling MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 pin MIL-C-5015/Top, 2 pin
Height 2.0 inch (50.8 mm) 1.13 inch (29 mm) 2.12 inch (53.85 mm)
Diameter 7/8 inch (22.2 mm) 1.36 inch (35 mm) 7/8 inch (22.2 mm)
Certifications CE
Comments •Online • Requires use of a Charge Amplifier (supplied) which must be mounted in 121°C area.
• Cable is not armored.• Online
• Requires use of a Charge Amplifier (supplied) which must be mounted in 121°C area.
• Cable is armored.• Online
11
Specialty Sensors
• Versions with velocity output
• Versions that measure both acceleration and temperature
• Versions that measure acceleration simultaneously in up to three axes
• Through-bolt mounting for simplified alignment
• Interface directly with vibration data collectors and FFT analyzers
Multi-axis accelerometers contain two or three independent acceleration sensing elements within the same housing. The sensing elements are oriented in mutually perpendicular geometries in order to respond to vibration in independent, orthogonal directions. Triaxial accelerometers contain three sensing elements. Each sensing axis contains a dedicated, built-in, low noise, microelectronic signal amplifier whose output signal is delivered to an independent cable lead or connector pin.
Multi-axis measurements are useful for radial vs. axial bearing vibration monitoring, machinery foundation troubleshooting, and structural impulse and response studies. Styles for low cost and precision requirements are differentiated by their sensitivity tolerances and extent of supplied NIST traceable calibration.
12 Specialty Sensors
Specialty Sensors
9100AT 9200AT 9100VO
Model NameCombination Acceleration and Temperature
Combination Acceleration and Temperature Velocity Output Sensor
Part Number EK-43810I EK-43811I EK-43808I
Data Sheet Number GMSI10-TD025A-EN-E GMSI10-TD026A-EN-E GMSI10-TD023A-EN-E
Dynamic
Sensitivity
English 100 mV/g 100 mV/in/sec
SI 10.2 mV/(m/s2) 3937 mV/m/sec
Accuracy +/- 5% +/- 10%
Measurement Range
English +/- 50 g +/- 50 in/sec
SI +/- 490 m/s2 +/- 1.27 m/s
Frequency Response
+/- 5% 0.6 - 4,000 Hz 0.5 - 6,500 Hz -
+/- 10% 0.4 - 5,000 Hz 0.4 - 7,500 Hz 4 - 4,500 Hz
+/- 3 dB 0.2 - 10,000 Hz 0.2 - 10,500 Hz 3 - 9,000 Hz
Resonance Frequency 20 kHz 25 kHz
Temperature Scale Factor 10 mV/°C
Temperature Measurement Range 2 to 121°C
Broadband Resolution (1 - 10,000 Hz)
English 50 μg 450 μin/s
SI 490 μm/s2 11.4 μm/s
Transverse Sensitivity ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC
Bias Output Voltage, nominal 8 - 12 VDC
Grounding case isolated
Settling Time ≤ 5.0sec ≤ 8.0sec ≤ 30.0sec
Environmental
Temperature Range -54 to 121°C
Shock Limit 5,000 g peak
Physical
Weight 93 gm 145 gm 94 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male 1/4 - 28 UNF Female
Output Connector / Cabling MIL-C-5015/Top, 3 pin MIL-C-5015/Side, 3 pin MIL-C-5015/Top, 2 pin
Height 2.0 inch (52.3 mm) 1.13 inch (28.7 mm) 2.06 inch (52.3 mm)
Diameter 7/8 inch (22.2 mm) 1.36 inch (34.5 mm) 7/8 inch (22.2 mm)
Certifications CE
Comments • If used with a switchbox, it must be powered.• Online
• Velocity Output• Portable or Online
Specialty Sensors 13
Specialty Sensors
9200VO 9900A 9900B
Model Name Velocity Output Sensor Triaxial Sensor Triaxial Sensor
Part Number EK-43809I EK-43802I EK-43803I
Data Sheet Number GMSI10-TD024A-EN-E GMSI10-TD018A-EN-E GMSI10-TD019A-EN-E
Dynamic
Sensitivity
English 100 mV/in/sec 100 mV/g
SI 3937 mV/m/sec 10.2 mV/(m/s2)
Accuracy +/- 10% +/- 5%
Measurement Range
English +/- 50 in/sec 50 g
SI +/- 1.27 m/s +/- 490 m/s2
Frequency Response
+/- 5% - 2.4 - 2,000 Hz
+/- 10% 2 - 2,500 Hz 1.7 - 5,000 Hz
+/- 3 dB 1.5 - 6,000 Hz 0.8 - 8,000 Hz
Resonance Frequency 10 kHz 20 kHz
Broadband Resolution (1 - 10,000 Hz)
English 400 μin/s 100 μg
SI 10.6 μm/s 981 μm/s2
Transverse Sensitivity ≤ 8% ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC
Bias Output Voltage, nominal 8 - 12 VDC
Grounding case isolated
Settling Time ≤ 30.0sec ≤ 3.0sec
Environmental
Temperature Range -54 to 121°C
Shock Limit 5,000 g peak
Physical
Weight 215 gm 139 gm
Case Material stainless steel
Mounting 1/4 - 28 Male 1/4 - 28 UNF
Output Connector / Cabling MIL-C-5015/Side, 2 pin MIL-C-26482/Side, 4 pin
Integral Cable, 10 ft., four-conductor shielded, polyurethane jacket
Height 1.13 inch (28.7 mm) 0.84 inch (21.2 mm) 0.82 inch (20.8 mm)
Length 1.5 inch (38.1 mm)
Diameter/Width 1.375 inch (34.9 mm) 1.5 inch (38.1 mm)
Certifications CE
Comments • Velocity Output• Portable or Online
• Use with cable EK-46654 only• Portable
• Integral Cable• Online
14 Specialty Sensors
15
4-20mA Sensors
• All sensors include additional RFI protection
• Two-wire, loop-powered, current output vibration sensors
• Choice of acceleration and/or velocity signals
• Interface with existing process control, monitoring, and alarm systems
• Reduce sophisticated analysis requirements
Loop-powered, 4-20 mA output, vibration sensing transmitters serve to provide measurement signals that are representative of the overall vibration levels being generated by all types of rotating machinery. This vibration signal may be interfaced with many types of current-loop monitoring equipment, such as recorders, alarms, PLC, DCS, and SCADA systems.
The vibration sensing transmitters capitalize on the use of existing process control equipment and HMI software for monitoring machinery vibration and alarming of excessive vibration levels. This practice offers the ability to continuously monitor machinery and provide an early warning detection of impending failure. With this approach, existing process control technicians may be utilized for monitoring the vibration levels while skilled vibration specialists are called upon only in the event that the vibration signal warrants more detailed signal analysis.
16 4-20mA Sensors
4-20mA Sensors
9842A 9942A 9842V 9942V
Model Name4-20 mA Sensor Output Acceleration
4-20 mA Sensor Output Acceleration 4-20 mA Sensor Output Velocity 4-20 mA Sensor Output Velocity
Part Number EK-48962 EK-48963 EK-48958 EK-48959
Data Sheet Number GMSI10-TD028B-EN-E GMSI10-TD043A-EN-E GMSI10-TD027B-EN-E GMSI10-TD041A-EN-E
Dynamic
Measurement Range
English 0.0 - 10.0 g rms 0.0 - 1.0 in/s pk
SI 0.0 - 98.1 m/s2 rms 0.0 - 25.4 mm/s pk
Current Output 4-20 mA
Amplitude Nonlinearity 1%
Frequency Response
+/- 10% 3 - 5,000 Hz 3 - 1,000 Hz
Broadband Resolution
English 0.05 g rms 0.005 in/s pk
SI 0.49 m/s2 rms 0.13 mm/s pk
Maximum Load Resistance 50 (Vs- 12) ohms
Electrical
Power Supply Voltage 12 - 30 VDC
Settling Time (within 2% of value) < 15 seconds
Environmental
Temperature Range -40 to 85°C
Physical
Weight 131 gm 108 gm 131 gm 108 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male 1/4 - 28 UNF Female 1/4 - 28 UNF Male
Output Connector / Cabling MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 Pin MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 Pin
Height 2.6 inch (66 mm) 1.41 inch (35.8 mm) 2.6 inch (66 mm) 1.41 inch (35.8 mm)
Diameter 1.0 inch (25.4 mm) 7/8 inch (22.2 mm) 1.0 inch (25.4 mm) 7/8 inch (22.2 mm)
Certifications CE
Comments •Online
Publication GMSI10-SG003A-EN-P - June 2006
4-20mA Sensors 17
4-20mA Sensors
9842T 9942T 9842V/2 9942V/2
Model Name 4-20 mA Sensor Output Velocity 4-20 mA Sensor Output Velocity 4-20 mA Sensor Output Velocity 4-20 mA Sensor Output Velocity
Part Number EK-48966 EK-48967 EK-48960 EK-48961
Data Sheet Number GMSI10-TD045B-EN-E GMSI10-TD046A-EN-E GMSI10-TD033B-EN-E GMSI10-TD039A-EN-E
Dynamic
Measurement Range
English 0.0 - 1.0 in/s pk 0.0 - 2.0 in/s pk
SI 0.0 - 25.4 mm/s pk 0.0 - 50.8 mm/s pk
Current Output 4-20 mA
Amplitude Nonlinearity 1%
Frequency Response
+/- 10% 3 - 1,000 Hz
Broadband Resolution
English 0.005 in/s pk
SI 0.13 mm/s pk
Maximum Load Resistance 50 (Vs- 12) ohms 50 (Vs- 12) ohms
Electrical
Power Supply Voltage 12 - 30 VDC
Settling Time (within 2% of value) < 15 seconds
Environmental
Temperature Range -40 to 85°C
Physical
Weight 131 gm 111 gm 131 gm 108 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male 1/4 - 28 UNF Female 1/4 - 28 UNF Male
Output Connector / Cabling 4 Pin Bayonet/Top 4 Pin Bayonet/Side MIL-C-5015/Top, 2 Pin MIL-C-5015/Side, 2 Pin
Height 2.6 inch (66 mm) 1.41 inch (35.8 mm) 2.6 inch (66 mm) 1.41 inch (35.8 mm)
Diameter 1.0 inch (25.4 mm) 7/8 inch (22.2 mm) 1.0 inch (25.4 mm) 7/8 inch (22.2 mm)
Certifications CE
Comments •Online
18 4-20mA Sensors
4-20mA Sensors
9842V2 9942V2
Model Name 4-20 mA Sensor Dual Output Acceleration/Velocity
4-20 mA Sensor Dual Output Acceleration/Velocity
Part Number EK-48956 EK-48951
Data Sheet Number GMSI10-TD029B-EN-E GMSI10-TD042A-EN-E
Dynamic
Measurement Range
English 0.0 - 1.0 in/s pk
SI 0.0 - 25.4 mm/s pk
Current Output 4-20 mA
Amplitude Nonlinearity 1%
Frequency Response
+/- 10% 3 - 1,000 Hz
Broadband Resolution
English 0.005 in/s pk
SI 0.13 mm/s pk
Maximum Load Resistance 50 (Vs- 12) ohms
Electrical
Power Supply Voltage 12 - 30 VDC
Settling Time (within 2% of value) < 15 seconds
Environmental
Temperature Range -40 to 85°C
Physical
Weight 131 gm 108 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male
Output Connector / Cabling MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 Pin
Height 2.6 inch (66 mm) 1.41 inch (35.8 mm)
Diameter 1.0 inch (25.4 mm) 7/8 inch (22.2 mm)
Certifications CE
Comments •Online
19
Intrinsically Safe Sensors
• Versions are CSA certified and/or EX compliant
• Top or side exit connector versions
• Hermetically sealed construction
• Interface directly with vibration data collectors
• Ideal for FFT analysis of vibration frequencies
• Measurements for machinery diagnostics
Before installing safety sensors, reference installation drawings, product drawings, and product specification sheets for both sensor and monitoring system.
Speciality sensors for mining and other applications are available upon request, please contact your nearest Rockwell Automation office or contact the High Tech Inside Sales Team at (740) 548-5733.
20 Intrinsically Safe Sensors
Intrinsically Safe Sensors
9100CSA 9100EX 9200CSA 9200EX
Model Name General Purpose Accelerometer General Purpose Accelerometer General Purpose Accelerometer General Purpose Accelerometer
Part Number EK-43786I EK-43787 EK-43790I EK-43791
Data Sheet Number GMSI10-TD006A-EN-E GMSI10-TD039A-EN-E GMSI10-TD008A-EN-E GMSI10-TD009A-EN-E
Dynamic
Sensitivity
English 100 mV/g
SI 10.2 mV/(m/s2)
Accuracy +/- 5%
Measurement Range
English +/-50 g 80 g peak +/-50 g 50 g peak
SI +/- 490 m/s2 +/- 784.8 m/s2 +/- 490 m/s2
Frequency Response
+/- 5% 0.58 - 4,000 Hz 1.5 - 5,000 Hz 0.5 - 6,500 Hz 3.0 - 5,000 Hz
+/- 10% 0.42 - 5,000 Hz 1.0 - 7,000 Hz 0.4 - 7,500 Hz 2.0 - 7,000 Hz
+/- 3 dB 0.2 - 10,000 Hz 0.5 - 15,000 Hz 0.2 - 10,500 Hz 1.0 - 12,000 Hz
Resonance Frequency 20 kHz 25 kHz 26 kHz
Broadband Resolution (1 - 10,000 Hz)
English 50 μg 600 μg 50 μg 600 μg
SI 490 μm/s2 5886 μm/s2 490 μm/s2 5886 μm/s2
Transverse Sensitivity ≤ 5%
Electrical
Power Requirement, Voltage Source 18 - 28 VDC 18 - 30 VDC 18 - 28 VDC 18 - 30 VDC
Bias Output Voltage, nominal 8 - 12 VDC
Grounding case isolated
Settling Time ≤ 5.0sec ≤ 8.0sec
Environmental
Temperature Range -54 to 121°C -50 to 120°C -54 to 121°C -50 to 120°C
Shock Limit 5,000 g peak
Physical
Weight 94 gm 112 gm 145 gm 135 gm
Case Material stainless steel
Mounting 1/4 - 28 Female 1/4 - 28 Male
Output Connector / Cabling MIL-C-5015/Top, 2 pin MIL-C-5015/Side, 2 pin
Height 2.06 inch (52.3 mm) 2.42 inch (61.47 mm) 1.13 inch (28.7 mm) 1.20 inch (30.48 mm)
Diameter 7/8 inch (22.2 mm) 1 inch (25.4 mm) 1.36 inch (34.5 mm) 1.05 inch (26.67 mm)
Certifications CE, CSA Div 1 Class 1; Group A, B, C & D; Temperature code T4
CE, Ex ia IIC T4, ATEX II 1G CE, CSA Div 1 Class 1; Group A, B, C & D; Temperature code T4
CE, Ex ia IIC T4, ATEX II 1G
Comments • Certified by CSA for Class l Division l Groups A, B, C, and D. Requires Safety Barriers for Class l Division l.
• Safety Barriers are required for Class l Division ll Groups A, B, C, and D unless certified under XM or other RA product’s certifications.
• Certified by Sira for Ex ia IIC T4 and ATEX II 1G.
• May be certified without safety barriers for Class l Division ll under other RA product certifications.
• Certified by CSA for Class l Division l Groups A, B, C, and D. Requires Safety Barriers for Class l Division l.
• Safety Barriers are required for Class l Division ll Groups A, B, C, and D unless certified under XM or other RA product’s certifications.
• Certified by Sira for Ex ia IIC T4 and ATEX II 1G.
• May be certified without safety barriers for Class l Division ll under other RA product certifications.
Intrinsically Safe Sensors 21
Intrinsically Safe Sensor
9842VCRT 9942VCRT
Model Name4-20 mA Sensor Output Velocity 4-20 mA Sensor Output Velocity
Part Number EK-48964 EK-48965
Data Sheet Number GMSI10-TD035B-EN-E GMSI10-TD044A-EN-E
Dynamic
Measurement Range
English 0.0 - 1.0 in/s pk
SI 0.0 - 25.4 mm/s pk
Current Output 4-20 mA
Amplitude Nonlinearity 1%
Frequency Response
+/- 10% 3 - 1,000 Hz
Broadband Resolution
English 0.005 in/s pk
SI 0.13 mm/s pk
Maximum Load Resistance 50 (Vs- 12) ohms
Electrical
Power Supply Voltage 12 - 30 VDC
Settling Time (within 2% of value) < 15 seconds
Environmental
Temperature Range -40 to 85°C
Physical
Weight 131 gm 108 gm
Case Material stainless steel
Mounting 1/4 - 28 UNF Female 1/4 - 28 UNF Male
Output Connector / Cabling MIL-C-5015/Top, 2 Pin MIL-C-5015/Side, 2 Pin
Height 2.6 inch (66 mm) 1.41 inch (35.8 mm)
Diameter 1.0 inch (25.4 mm) 7/8 inch (22.2 mm)
Certifications CE, CSA, Ex ia II C
Comments •Certified by CSA for Class l Division l Groups A, B, C, and D. Requires Safety Barriers for Class l Division l.
•Certified by Sira for Ex ia IIC T4 and ATEX II 1G.•Online
22 Intrinsically Safe Sensors
System Certifications
9100CSA 9200CSA 9100EX 9200EX
Protection Monitors
XM-120 / XM-121 / XM-122 / XM-123 •CSA Certified for Class I, Division 2 Groups A, B, C and D•CSA Certified for Class I, Division 1 Groups A, B, C and D
with appropriate certified barrier
XM-160 / XM-161 / XM-162 •CSA Certified for Class I, Division 2 Groups A, B, C and D•CSA Certified for Class I, Division 1 Groups A, B, C and D
with appropriate certified barrier
Portable Data Collectors
Enpac 2500 •CSA Certified for Class I, Division 2 Groups A, B, C and D
Enpac Ex •Sira Certified for EEx ia IIC T4•Sira Certified for ATEX II 1G
Online Surveillance Monitoring
Enwatch •CSA Certified for Class I, Division 2 Groups A, B, C and D•CSA Certified for Class II, Division 2, Groups E, F, G
23
Accessories and Technical Information
Cables for Portable Instruments - Enpac and dataPAC
Cable for Permanent Installations - XM and Enwatch
IMPORTANT These cables are not used with the Enpac Ex.
Cables for 2-PIN MS Style Sensor Connectors
For Models Cable Part Number Description
9000A, 9000A-LBV, 9010, 9010-LBV, 9100,
9100CSA, 9100EX, 9100FM, 9100L, 9100T,
9100VO, 9200, 9200CSA, 9200FM, 9200L,
9200T, 9200VO, 9300, 9400, 9500LF, 9500HLF,
9600
EK-36960-C-006 Cable Assembly, 6 ft Coiled; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-005 Cable Assembly, 5 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-010 Cable Assembly, 10 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-015 Cable Assembly, 15 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-020 Cable Assembly, 20 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-025 Cable Assembly, 25 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-040 Cable Assembly, 40 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-36960-S-050 Cable Assembly, 50 ft Straight; 2-Socket Connector to 7-Pin LEMO Connector
EK-47787 Cable Assembly, 6 ft Coiled; 90 Degree, 2-Socket Connector to 7-Pin LEMO Connector
Cables for 5-44 Style Sensor Connector
For Models Cable Part Number Description
9700A EK-46669 Cable Assembly, 5 ft; 5-44 Connector to BNC Plug Note: LEMO to BNC Straight Cable, 4’ (EK-46252) and Connector BNC to BNC Barrel (EK-37961) Required
EK-39458 Cable Assembly, 10 ft; 5-44 Connector to BNC Plug Note: LEMO to BNC Straight Cable, 4’ (EK-46252) and Connector BNC to BNC Barrel (EK-37961) Required
Cables for 10-32 Style Sensor Connector
For Models Cable Part Number Description
9700B EK-35579 Cable Assembly, 5 ft; 10-32 Connector to BNC Plug Note: LEMO to BNC Straight Cable, 4’ (EK-46252) and Connector BNC to BNC Barrel (EK-37961) Required
Cables for 4-PIN Bendix Style Connector
For Models Cable Part Number Description
9900A EK-46654-C-006 Cable Assembly, 6 ft Coiled; 4-Socket Bendix Connector to 7-Pin LEMO Connector
Splash Proof Cables for 2-PIN Sensors
For Models Cable Part Number Description
9000A, 9000A-LBV, 9010, 9010-LBV, 9100,
9100CSA, 9100EX, 9100FM, 9100L, 9100T,
9100VO, 9200, 9200CSA, 9200FM, 9200L,
9200T, 9200VO, 9300, 9400, 9500LF, 9500HLF,
9600, 9842V, 9842V/2, 9842A, 9842VCS,
9842VFM
EK-46800I Splash Proof Cable Assembly, 16ft; 2-socket Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
EK-46801I Splash Proof Cable Assembly, 32ft; 2-socket Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
EK-46802I Splash Proof Cable Assembly, 64ft; 2-socket Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
EK-46806I Splash Proof Cable Assembly, 112ft; 2-socket Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
24 Accessories and Technical Information
Switch Boxes, Switch Panels, and Terminal Boxes
Cost Effective Cables for 2-PIN Sensors
For Models Cable Part Number Description
9000A, 9000A-LBV, 9010, 9010-LBV, 9100,
9100CSA, 9100EX, 9100FM, 9100L, 9100T,
9150HT Amplifier, 9150HTA Amplifier, 9200,
9200CSA, 9200FM, 9200L, 9200T, 9300, 9400,
9500LF, 9500HLF, 9600, 9842V, 9842V/2,
9842A, 9842VCS, 9842VFM
EK-44134 Cost Effective Cable Assembly, 16ft; 2-socket Molded Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
EK-44135 Cost Effective Cable Assembly, 32ft; 2-socket Molded Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
EK-44136 Cost Effective Cable Assembly, 64ft; 2-socket Molded Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
EK-44137 Cost Effective Cable Assembly, 112ft; 2-socket Molded Connector to Blunt Cut; Twisted-shielded pair; Teflon Jacket
Splash Proof Cables for 3-PIN Sensors
For Models Cable Part Number Description
9100AT, 9200AT, 9842V2 EK-46803I Splash Proof Cable Assembly, 16ft; 3-socket Connector to Blunt Cut; Shielded 3-Conductor; Teflon Jacket
EK-46804I Splash Proof Cable Assembly, 32ft; 3-socket Connector to Blunt Cut; Shielded 3-Conductor; Teflon Jacket
EK-46805I Splash Proof Cable Assembly, 64ft; 3-socket Connector to Blunt Cut; Shielded 3-Conductor; Teflon Jacket
2-Channel Products
Part Number Description
EK-45077 Termination Box 2-Channel Termination Box; Nema 4X; (2) BNC Sensor Output; No Power Supply; Cable Grip; Composite Material
4-Channel Products
Part Number Description
EK-44391 Termination Box 4-Channel Termination Box; Nema 4X; (4) BNC Sensor Output; No Power Supply; Cable Grip; Composite Material
6-Channel Products
Part Number Description
EK-41585 Switchbox 6-Channel Switchbox; Nema 4X; (1) BNC Vibration Output & (1) BNC Temp Output; No Power Supply; Composite Box
EK-44167 Switchbox 6-Channel Switchbox; Nema 4X; (1) BNC Sensor Output & (1) BNC Tach Output; No Power Supply; Stainless Steel
EK-44397 Termination Box 6-Channel Termination Box; Nema 4; (6) BNC Sensor Outputs; No Power Supply; Painted Steel
EK-48174 Switchbox 6-Channel Switchbox; Nema 4X; (1) BNC Vibration Output & (1) BNC Tach Output; No Power Supply; Composite Box; w/ Bias Meter
12-Channel Products
Part Number Description
EK-43617 Switchbox 12-Channel Switchbox; Nema 4; (1) BNC Internally Powered Sensor Output; (1) BNC Vib & (1) BNC: ICP Power; 110vac
EK-44171 Switchbox 12-Channel Switchbox; Nema 4X; (1) BNC Sensor Output & (1) BNC Temp Output; No Power Supply; Stainless Steel Box
EK-48177 Switchbox 12-Channel Switchbox; Nema 4X; (1) BNC Sensor Output & (1) BNC Tach Output; No Power Supply; Bias Voltage Meter; Stainless Steel Box
EK-48176 Switchbox 12-Channel Switchbox; Nema 4X; (1) BNC Sensor Output & (1) BNC Tach Output; No Power Supply; Bias Voltage Meter; Composite Box
EK-45079 Switchbox 12-Channel Switchbox; Nema 4X; (1) BNC Vibration Output & (1) BNC Tach Output; No Power Supply; Composite Box
Accessories and Technical Information 25
Connectors
16-Channel Products
Part Number Description
EK-40434 Switchbox 16-Channel Switchbox; Nema 4; (1) BNC Sensor Output; EMONITOR Nameplate; No Power Supply; Painted Steel Box; (ESWB-16)
EK-40435 Switchbox 16-Channel Switchbox; Nema 4; (1) BNC Sensor Output; EMONITOR Nameplate; No Power Supply; Stainless Steel Box; (ESWB-16-SS)
EK-40436 Switchbox 16-Channel Switchbox; Nema 4; (1) BNC Sensor Output; EMONITOR Nameplate; No Power Supply
EK-40437 Switchbox 16-Channel Switchbox; Nema 4; (1) BNC Sensor Output; EMONITOR Nameplate; No Power Supply; Oversized Stainless Steel Box; (ESWBO-16-SS)
24-Channel Products
Part Number Description
EK-42883 Switchbox 24-Channel Switchbox; Nema 4; (1) BNC Internally Powered Sensor Output; (1) BNC Collector; Powered Output; (1) BNC Tachometer Output; Accelerometer Constant Current PWR Supply (110vac); Painted Steel Enclosure
32-Channel Products
Part Number Description
EK-40438 Switchbox 32-Channel Switchbox; Nema 4; (1) BNC Sensor Output for each 16-Channel Switch; EMONITOR Nameplate; No Power Supply; Painted Steel Box; (ESWB-32)
EK-40439 Switchbox 32-Channel Switchbox; Nema 4; (1) BNC Sensor Output for each 16-Channel Switch; EMONITOR Nameplate; No Power Supply; Stainless Steel Box; (ESWB-32-SS)
EK-40440 Switchbox 32-Channel Switchbox; Nema 4; (1) BNC Sensor Output for each 16-Channel Switch; EMONITOR Nameplate; No Power Supply; Oversized Painted Steel Box; (ESWBO-32)
EK-40441 Switchbox 32-Channel Switchbox; Nema 4; (1) BNC Output Connector for each 16-Channel Switch; EMONITOR Nameplate; No Power Supply; Oversized Stainless Steel Box; (ESWBO-32-SS)
36-Channel Products
Part Number Description
EK-42884 Switchbox 36-Channel Switchbox; Nema 4; (1) BNC Internally Powered Sensor Output; (1) BNC Collector; Powered Output; (1) BNC Tachometer Output; Accelerometer Constant Current PWR Supply (110vac); Painted Steel Enclosure
48-Channel Products
Part Number Description
EK-42885 Switchbox 48-Channel Switchbox; Nema 4; (1) BNC Internally Powered Sensor Output; (1) BNC Collector; Powered Output; (1) BNC Tachometer Output; Accelerometer Constant Current PWR Supply (110vac); Painted Steel Enclosure
Accelerometer and Velocity Connectors
Part Number Description
EK-44144 2-Socket MS Connector (Aluminum)
EK-44145 2-Socket Splash proof MS Connector with SS Ring (Requires EK-44148)
EK-44146 3-Socket Splash proof MS Connector with SS Ring (Requires EK-44148)
EK-44148 Splash proof MS Connector Assembly Tool Kit for 25 Connectors - Connectors are sold separately
EK-41755 2-Socket MS Connector Kit - Splash proof, Shielded Ground with Epoxy
EK-04366 2-Socket MS Connector Field Install
EK-14797 2-Socket MS Connector Field Install - Right Angle
EK-15039 2-Socket MS Connector Field Install - High Temperature
26 Accessories and Technical Information
Mounting Accessories
Application Notes
Mounting Accessories
Part Number Description
Magnet
EK-46670 Flat Rare Earth Magnetic Base - 5-40 Tapped Hole, 0.417" Dia
EK-44162 Flat Rare Earth Magnetic Base - 10-32 Thread Stud, .68" Dia
EK-42118 3/4" Dia Curved Surface Magnet (14 lb. Pull, 1/4 x 28)
EK-42120 3/4" Dia Flat Surface Magnet (15 lb. Pull, 1/4 - 28)
EK-41717 1" Dia Curved Surface Magnet (35 lb. Pull, 1/4 x 28)
EK-42121 1" Dia Flat Surface Magnet (35 lb. Pull, 1/4 x 28)
EK-24746 1 1/2" Dia Magnetic Base, 1/4-28 Thread (11.3 kg or 25 lb. Pull)
EK-41529 1 1/2" Dia Curved Surface Magnet (55 lb. Pull, 1/4 x 28)
EK-42123 1 1/2" Dia Flat Surface Magnet (50 lb. Pull, 1/4 x 28)
EK-42119 2" Dia Curved Surface Magnet (80 lb. Pull, 1/4 x 28)
EK-04332 2.25" Dia Curved Surface Magnet (65 lb. Pull, 1/4 x 28)
Probe
EK-41530 Probe Tip 4" Length, 1/2" Hex Tapered to Point (1/4 x 28)
EK-41915 Probe Tip 8" Length, 1/2" Hex Tapered to Point (1/4 x 28)
EK-01103 Probe Tip 9" Length with 1/4-28 Stud, Aluminum
Permanent
EK-48254 Mounting Pads, To Fit Between Motor Fin; 0.250" Thick, 2.125" Long
EK-48253 Mounting Pads, To Fit Between Motor Fin; 0.250" Thick, 1.375" Long
EK-48255 Mounting Pads, To Fit Between Motor Fin; 0.500" Thick, 1.625" Long
EK-48256 Mounting Pads, To Fit Between Motor Fin; 0.500" Thick, 2.375" Long
EK-44151 Mounting Stud - 10/32 to 10/32
EK-44152 Mounting Stud - 10/32 to 1/4-28
EK-44153 Mounting Stud - 1/4-28 to 1/4-28
EK-44154 Mounting Stud - 1/4-28 to M8
EK-44155 Mounting Stud - 1/4-28 to M6
EK-42053 Spotface Tool for Sensor Mounting, 1.25" Dia, 1/4-28 Pilot
EK-44161 Mounting Base for Epoxy Mount with 10-32 Stud
EK-44156 Epoxy Kit for 2 Sensor Bases
EK-44164 Mounting Base, Epoxy Mount with 1/4 x 28 Threaded Thru Hole
EK-44801 Epoxy, Versilox 406, Packet for Two Mounting Bases
EK-44158 Quiklok Mounting Base for Stud Mounting on Machine
EK-44159 Quiklok Mounting Base for Epoxy Mounting to Target Machine
EK-44160 Quiklok Accelerometer Base, Mounts to Accel
Application Notes
Part Number Description
GMSI10-AP042A-EN-E Accelerometer Calibration
GMSI10-AP043A-EN-E Selecting & Installing Accelerometers
GMSI10-AP044A-EN-E Troubleshooting Using Bias Voltage
GMSI10-AP045A-EN-E Accelerometer Mounting Techniques
GMSI10-AP046A-EN-E Powering ICP Accelerometers
GMSI10-AP047A-EN-E Driving Long Cable Lengths
Accessories and Technical Information 27
Typical Vibration Measurement Systems
Accelerometers are implemented into measurement systems in a number of different ways. The installation technique typically falls into one of two categories, either permanently mounted, or carried from point to point in a route based measurement or analysis scheme. The entire measurement system, however, can take on a variety of forms, depending on sensor type used and the goal of the monitoring program. This section illustrates many of the popular or recommended approaches, which comprise complete vibration measurement and monitoring systems.
Portable Data Collector and Accelerometer
Portable Data Collector and Permanently Installed Accelerometers
Precision Industrial Accelerometer
Magnetic Mounting Base
Sensor to Enpac2500 Cable
Enpac 2500
Switch Box
Sensor to DataCollector Cable
Enpac 2500Sensor Cables
Permanently Installed Accelerometers
28 Accessories and Technical Information
Online Surveillance Monitoring and Permanently Installed Accelerometers
4-20mA Output Sensor System
XM System and Permanently Installed Accelerometers
Junction Box
Enwatch
Sensor to Enwatch Cable
Enwatch to Computer
Cable
Analysis Software
Sensor Cables
PermanentlyInstalled
Accelerometers
ProgrammableLogix
Controller
Sensor toPLC Cable
Junction Box
Sensor Cables
PermanentlyInstalled
Accelerometers
Analysis Software
XM SerialCommunication
Cable
XM Machine Monitor
Sensor to XM Cable
Junction Box
Sensor Cables
PermanentlyInstalled
Accelerometers
GSMI10-SG001A-EN-E July 2006 Copyright ©2006 Rockwell Automation, Inc. All Rights Reserved. Printed in USA
Top Related