8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
1/57
Microwave Equipment Hardware
Installation Guide
Microwave Product Customer Service Dept.2009-1
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
2/57
Content
Installation Flow
Installation Preparative
Installation Steps
Hardware Installation Check
Commissioning Test
Appendix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
3/57
Installation Flow Sort and count goods
Check if com pleted? supply again goods
Check if the installing
conditions is ok?
Install indoor part
Yes
Yes
Feedback
responsibility party
N o
N o
Install outdoor part
Check installation
Check if the installing
result is ok?
Clean the work local
End
Correct
Yes
No
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
4/57
Content
Installation Flow
Installation Preparative
Installation Steps
Hardware Installation Check
Commissioning Test
Appendix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
5/57
Installation Preparative
1. Sort and count goods
1. Record delivery table information for each site.
2. Record information of counting and inspecting goods.
3. If the goods information does not comply with the site
information, ask for supplement.
2. Preparations
Documents
Tools
Manpower
Check installation conditions
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
6/57
Documents
Microwave implementation
data table
Microwave link to olo
Site implementation plan view
design drawing
Link performance table
Link sectional drawing
E1 distribution table
Documents Preparation beforeImplementation
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
7/57
Tools
SN Name QuantityMain
parameter
Remark
1 Multimeter 1 With buzzer
2 Compass 2
Tools and instruments and
operation safety requirements
4 Pull RopeDecided by
antenna height
5 Assembledtools
2
Caution
Follow the implementation regulation strictly during installation.
All installation stuff must wear safety helmet and safety belt.
All tools for electrical installation and operation must have insulation treatment.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
8/57
Manpower
Antenna caliber: 0.3m/0.6m/1.2m
Decide manpower mainly according to antenna caliber. Recommendation as
follows:
5 People
Antenna caliber: 1.8m/2m
Antenna caliber: 2.4m/3.2m
8 People
10 People
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
9/57
Check Installation Conditions
Check indoor installation conditions
Check outdoor installation conditions
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
10/57
Check Indoor Installation Conditions
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
11/57
Check Installation Condition
Check indoor installation condition
Check outdoor installation condition
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
12/57
Check Outdoor Installation Condition
Tower Pole Outdoor cable rack
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
13/57
Content
Installation Flow
Installation Preparative
Installation Steps
Hardware Installation Check
Commissioning Test
Appendix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
14/57
Installation Steps
1 Indoor Installation
2 Outdoor Installation
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
15/57
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
16/57
Indoor Installation
Fixing Rack
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
17/57
Indoor Installation
The adjacent racks should
be pressed compact, without
any spacing over 3mm.
Fixing Rack
The adjacent racks of the
same type should be uniform
In height, with a deviation
not more than 2mm.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
18/57
Indoor Installation
The rack (cable distribution frame,
or power cabinet) should not have
a vertical error exceedin 1 of its
height.
Fixing Rack
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
19/57
Indoor Installation
Fixing IDU
Caution:
IDU must be fixed firmly on the stably installed rack.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
20/57
Indoor Installation
IDU Installation Points
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
21/57
Indoor Installation
Connect IDU I/O Board (75)
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
22/57
Indoor Installation
IDU Power
connector plugs
Caution:
Do not mistake the power supply polarity. It may cause IDU damage.
ZTE IDU Power
connector jack
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
23/57
Indoor Installation
IDU Grounding
IDU grounding point
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
24/57
Indoor Installation
Make IF cable head
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
25/57
Indoor Installation
Make IF cable head
IF cable connecter shall be fixed with the cable tightly and has good electrical contact.Wrap the connecter end and the cable with insulation tape for about 3cm. Wrap evenly and tightly.
Check IF cable short with multimeter.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
26/57
Line-up E1 cable
Indoor Installation
Specification and routing of E1 signal cable shall comply with design requirements.
Cut E1 cables according to the design before wiring, and make clear marks at both ends.
Weld properly on correct position. The welding part shall be smooth and even with no point.
Line-up the cables orderly and neatly.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
27/57
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
28/57
Indoor Installation
Power supply
terminals busbar
Caution:
The power supply terminal busbar shall be installed upper right. Power cables shall be
lined orderly. Connect the cables strictly following the regulation. Avoid short.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
29/57
Indoor Installation
The power cable and ground cable
terminals should be crimped firmly,and the spring washers should be
pressed flat when crimping a bolt.
Use copper lugs according to the
core diameters and bolt diameters.
It is not allowed to cut off partial
core to suit a small copper lug or cut
open a copper lug to suit a large bolt.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
30/57
Indoor Installation
The copper lugs and the bare part of
connected wire should be wrapped
tightly with insulating tape or shrinkable
tubes. When insulating tape is applied,
its color should conform to the color
label requirements.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
31/57
Indoor Installation
Labels shall have
the same direction
Its not allowed!
a es no n or er
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
32/57
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
33/57
Indoor Installation
In the case of upward cabling, the
cables should be mounted directly
along the cabling rack, and should
Wiring Requirements
not e a t g t y aga nst t e eat-s n
panel on the top of the cabinet.When cabling along the upper part
of the cabinet is necessary, the cables
should be spaced 10cm away from
the heat-sink panel on the top of the
cabinet.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
34/57
Indoor Installation
The downward cables, when piled
up on the floor, cannot exceed
of the floor height, or ventilation
Wiring Requirements
.
For the cables outside a cabinet, the
part over one meter away from thecabinet is not allowed to intercross.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
35/57
Indoor Installation
The power cable, signal cable, and tail
fiber should be bundled and wired
separately .The power cable and signal
cable outside a cabinet should be
s aced over 5cm a art without
overlapping and mixture.
The insulating jacket of a cable is in
good condition, without core exposed.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
36/57
Indoor Installation
Cables Line-up
No cross. Fix with ties or feeder clip every 1m~1.5m.
Cables shall be tied and lined orderly and neatly.IF cables shall not cross on the cable rack. Do not tie IF cable together with
grounding cable and power cable.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
37/57
Outdoor Installation
Install Antenna Pole
0.3m/0.6m 1.2m
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
38/57
Outdoor Installation
ODU 1+0 Integrated Installation
Caution:
Mount ODU to the antenna and connect the wave guide connecters of the antenna and
ODU. Make sure the waterproof gasket is complete and in good condition. Fasten 4 buckles.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
39/57
Outdoor Installation
ODU 1+1 Integrated Installation
Caution:
Mount 2 ODU onto a hybrid and connect the hybrid to the antenna. Make sure the
waterproof gasket is complete and in good condition. Fasten 4 bolts.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
40/57
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
41/57
Outdoor Installation
ODU 1+1 Separated Installation
Caution:
Mount 2 ODU to a hybrid and install the hybrid to a bracket. Fix the bracket to the pole
with a U bolt. Connect antenna and the bracket with a flexible wave guide.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
42/57
Outdoor Installation
1 2
Mounting Antenna
34
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
43/57
Outdoor Installation
ODU IF cable connecter
Caution:
Wrap the connecter with tape and fix with ties tightly.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
44/57
Outdoor Installation
ODU Grounding
Caution:
Grounding cable shall be connect to the nearest grounding point. Cables can not be
winded together.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
45/57
Outdoor Installation
IF cable grounding
Caution:
Wrap the connecting part with waterproof mud and tape.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
46/57
Outdoor Installation
Outdoor IF cable line up and fix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
47/57
Outdoor Installation
The feeder must have a waterproof
arch before entering an equipment
room.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
48/57
Content
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
49/57
Content
Installation Flow
Installation Preparative
Installation Steps
Hardware Installation Check
Commissioning Test
Appendix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
50/57
Hardware Installation Check
IDU and ODU have proper grounding.
Check input power voltage and polarity.
IF cable connect ODU and IDU properly.
IF cable and signal cable shall be lined tidily and orderly.
Waterproof treatment of IF cable connecters.
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
51/57
Hardware Installation Check
Check the power polarity and cable radius.Power supply check
IF cable check Check the IF cable connecter, if there is short orbad contact.
Rack fix checkCheck if the rack is fixed tightly.
E1 cable checkCheck if the E1 cable and connecter are weldedTightly, and E1 cables connect right.
IF cable connecter
waterproof check Check if the waterproof is properly done.
Antenna check Check if the antenna is fixed tightly.
Content
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
52/57
Content
Installation Flow
Installation Preparative
Installation Steps
Hardware Installation Check
Commissioning Test
Appendix
Commissioning Test
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
53/57
Commissioning Test
Tributary 1 outTributary 2 in
Tributary 2 out
Tributary 3 in
Tributary 1 in
MicroStar
radio
MicroStar
radio
Bit error testTest method:
Remote endLocal end
Bit Error
Analyzer
Tributaryn out
Tributaryn in
Tributaryn out
After microwave link is setup, check E1 bit error with bit error analyzer.
Confirm if E1 channel runs normally.
Use management software of the equipment to operate bit error test.
Remote end self loop
Content
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
54/57
Content
Installation Flow
Installation Preparative
Installation Steps
Hardware Installation Check
Commissioning Test
Appendix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
55/57
Appendix
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
56/57
Appendix
Bit error analyzer operation introduction
Inward Loop back test
E1 interface circuit E1 interface circuit
Bit error
analyzer
8/13/2019 09 Microwave Equipment Hardware Installation Guide [Compatibility Mode]
57/57
Top Related