GGWM04 1
2-D STRESS ANALYSIS2-D STRESS ANALYSIS • Introduction to 2-D Stress Analysis• 2D and 3D Stresses and Strains• von Mises and Tresca Yield Criteria• 2-D Stress and Strain Results in
NASTRAN
GGWM04 2
Introduction to 2-D Stress Introduction to 2-D Stress Analysis Analysis
Up until now, we have only used rod shaped structural finite elements. These elements have been used to model framed or articulated structures such as trusses and frames.
We are now going to begin working with two dimensional (planar) triangular (3 noded) or quadrilateral (4 noded) elements defined in a two dimensional plane to model 2-D dimensional elastic solid mechanisms and structures.
GGWM04 3
Introduction to 2-D Stress AnalysisIntroduction to 2-D Stress AnalysisQuestion: Why 2-D Stress Analysis?
Answer: In complex shaped structural or machine components stress concentration effects are often important factors that must be considered in the design process
Note: A 1-D Beam or Truss (rod) analysis of the tension member shown below ignores the stress concentration in the fillet section and at the hole.
Tension member
GGWM04 4
Introduction to 2-D Elastic Stress AnalysisIntroduction to 2-D Elastic Stress AnalysisTwo-dimensional stress analysis allows the engineer to
determine detailed information concerning deformation, stress and strain, within a complex shaped two-dimensional elastic body.
Assumptions• Deformations and strains are very small• Material behaves elastically – stress and strain
are related by Hooke’s Law.• Hooke’s Law is a matrix equation relating 3
normal stresses and one shear stress to 3 normal strains and one shear strain }{]D[}{or}]{D[}{ 1
GGWM04 5
Introduction to 2-D Elastic Stress AnalysisIntroduction to 2-D Elastic Stress Analysis
2-D Stress analysis allows the engineer to model complex 2-D elastic bodies by discretizing the geometry with a mesh of finite elements.
Modeled as
GGWM04 6
Introduction to 2-D Stress AnalysisIntroduction to 2-D Stress Analysis
Each finite element will deform because of the applied loading and boundary conditions on the body.
Applied loading – generates
deformation and stresses
Each node displaces in x and z direction
x
z
u2x
u2z
1
2
3
4
GGWM04 7
Introduction to 2-D Stress AnalysisIntroduction to 2-D Stress AnalysisEvery point within the element may translate in
the x and z direction P(x,z) -> P’(x+ux, z+uz)
Note: ux and uz: x- and z-displacements are bi-linear functions of x and z.
where a0, a1,.. b3 are unknown constants
x
z
ux
uz
P
P’
xzbzbxbb)z,x(uxzazaxaa)z,x(u
3210z
3210x
GGWM04 8
Introduction to 2-D Stress AnalysisIntroduction to 2-D Stress AnalysisIn 1-D analysis assuming small displacements
and elastic material behavior we have:
a) A strain-displacement eqn.,
and, b) a stress-strain eqn. (1D Hooke’s Law)
Question: What is the 2D or 3D form of these equations?
dxdu
LLL
0
0
E
GGWM04 9
2-D Strain-Displacement Equations2-D Strain-Displacement Equations
xux
x
z
uzz
There are two normal strains and :x z
xu
zu zx
xz
and one shear strain :xz
x
z
x
x
z
z
x
z
xz
Below are examples of simple constant strain stateswhere only one strain component is non-zero!
GGWM04 10
2-D Strain-displacement Equations2-D Strain-displacement Equations
Question: What are the variations of the strain components for a element where the displacement field is defined by:
?
Note: ux and uz: x- and z-displacements are bi-linear functions of x and z.
where a0, a1,.. b3 are unknown constants
x
z
ux
uz
P
P’
xzbzbxbb)z,x(uxzazaxaa)z,x(u
3210z
3210x
GGWM04 11
3D Isotropic Stress/Strain 3D Isotropic Stress/Strain LawLaw
Three-dimensional Hooke’s Law: stress/strain relationships for an isotropic material
x
z
yσy
σy
σz
σz
σxσx
As you recall, an isotropic body can have normal stresses acting on each surface: σx, σy, σz
When the only normal stress is σx this causes a strain along the x- axis according to Hooke’s Law
Ex
x
GGWM04 12
x
x
3D Isotropic Stress/Strain 3D Isotropic Stress/Strain LawLaw
Note, that a tensile stress in the x direction, produces a negative strains in the y and z directions This is called the Poisson effect.
These negative strains are computed via:
where:
E is Young’s Modulus ν is Poisson’s ratio
Ex
zy
GGWM04 13
3D Isotropic Stress/Strain 3D Isotropic Stress/Strain LawLaw
Since the material is isotropic, application of normal stresses in the x, y, and z directions generates, a total normal strain in the x direction:
+ +
EEEzyx
x
x
x
yz
y z
GGWM04 14
3D Isotropic Stress/Strain 3D Isotropic Stress/Strain LawLaw
The total normal strains in the y and z directions can be determined in a similar manner:
EEE
EEE
EEE
zyxz
zyxy
zyxx
GGWM04 15
3D Isotropic Stress/Strain 3D Isotropic Stress/Strain LawLaw
Rearranging the above equations and yields 3 equations relating normal stresses and strains :
These equations can also be written in matrix notation: {σ}=[D]{ε}
])1([)21)(1(
])1([)21)(1(
])1([)21)(1(
zyxz
zyxy
zyxx
E
E
vE
GGWM04 16
Shear Stress/Strain RelationshipsShear Stress/Strain RelationshipsHooke’s law also applies for shear stress and
strain: τ=Gγ where G is the shear modulus, τ is a shear stress, and γ is a shear strain. For 3-D this results in a further 3 equations.
x
z
yσy
σy
σz
σz
σxσxτxy
τyxzxzxzx
yzyzyz
xyxyxy
G2G
G2G
G2G
GGWM04 17
Introduction to 2-D Stress Introduction to 2-D Stress Analysis Analysis
2-D planar elements are used to model complex 2-D geometries. They must connect at common nodes to form continuous structures. They are extremely important in the following analysis types:
Plane Stress Plane Strain Axisymmetric
GGWM04 18
Plane StressPlane StressPlane Stress, in NASTRAN, is defined to be a state of stress
in which the normal and shear stresses perpendicular to the x-z plane are zero, the y-thickness is very small, and the constraints (TX,TZ) and loads act only in the x-z plane and throughout the y-thickness.
•σy = 0
• τxy= 0, τyz=0
• ‘thickness’, y dimension, is very small compared to x and z dimensions
•Loads act only in the x-z plane and throughout the y-thickness
y
x
z
F1
F3
GGWM04 19
Plane StrainPlane StrainPlane Strain, in NASTRAN, is defined to be a state of strain
in which the normal strain in the y-direction, εy and the shear strains, γxy and γyz are zero. Note, the y-thickness of the body is very large, and constraints and loads act in x-z plane throughout thickness.
y x
z
•The ‘thickness’, y-dimension of the body is very large (“infinite”). Note, the NASTRAN finite element model analyzes only a ‘unit’ thickness
•Loads and constraints act only in the x-z plane through a unit y-thickness
• Forces are defined as force per unit y-length
•A plane stress state, where y is a very large value, does not approximate plane strain conditions!
• εy = 0, γxy= 0, γyz =0
F
F
GGWM04 20
Axisymmetric AnalysisAxisymmetric AnalysisAxisymmetric conditions exist when the problem
geometry is such that the z-axis is an axis of symmetry, and the displacement is radially symmetric (independent of In this case the only non-zero shear strain, is γxz. Note, that loads and constraints act over a ring defined by 0 < in the x-z plane.
The only shear strain that is non-zero is γxz
A ‘thickness’of 1 radian in the direction around the z-axis is modeled by NASTRAN
z
x
GGWM04 21
von-Mises Stressvon-Mises StressA stress quantity that is proportional to the the strain
energy density associated with a change in shape (with a zero volume change) at a material point is the von-Mises stress which is defined by:
NOTE: the von-Mises stress is a scalar measure of the stress state (the normal and shear stresses) at any point within a body
)(6)()()(2
1 2zx
2yz
2xy
2xz
2zy
2yxvm
GGWM04 22
von Mises Yield von Mises Yield CriterionCriterion
The von Mises criterion is an experimentally based law that can be used to determine whether the stress state in a material causes plastic flow (or yielding). Note, the von Mises criterion is based on the strain energy density associated with a change in shape (with a zero volume change) at a material point.
The criterion simply states that when: the material point is
elastic the material point is
yielding
Y Y
vm
vm
GGWM04 23
Tresca Yield CriterionTresca Yield Criterion Tresca yield criterion is another material model
which may be used to determines whether a stress state in a material causes yielding.
The criterion simply states that when: the material point is elastic the material point is yielding
YY
Tresca
Tresca
3 2 1Tresca
2
τ 31max
maxTresca 2
GGWM04 24
2D Stress Analysis Results in 2D Stress Analysis Results in NASTRANNASTRAN
After analyzing an NASTRAN model, results in superview can be found:
• With displacement just as we did with beam and truss models
• In results von Mises• In results Stress tensor Global Based
– yy is the normal stress in y direction– zz is the normal stress in the z direction– yz is the in-plane shear stress
Top Related