© 2012 Delmar, Cengage Learning
Brake Service
Chapter 58
© 2012 Delmar, Cengage Learning
Objectives• Inspect brake systems and recommend needed
repairs• Diagnose brake system problems• Perform brake repairs and adjustments using
the correct materials and procedures
© 2012 Delmar, Cengage Learning
Introduction and Brake Inspection
• This chapter deals with hydraulic brake systems– Inspection
– Diagnosis
– Repair
• Thorough inspection of the braking system– Performed before any repairs
• Start with pedal and master cylinder
© 2012 Delmar, Cengage Learning
Check Brake Pedal Feel• Check the travel of brake pedal
– Apply foot brakes• Should be ample amount of pedal reserve
• Pedal should feel firm, not spongy– Spongy brake pedal indicates air or moisture in
the system• Calling for a brake bleed
© 2012 Delmar, Cengage Learning
Master Cylinder Inspection• Fluid movement past vent port
– Should always be visible when pedal is applied
• Heavy surge from compensating port – Indicates air in system
• Power booster: operating correctly– Sound of air rushing into booster
• Apply the brakes – Test brake lights
• Hydraulic safety switch service– Brake warning lamp operates during braking
© 2012 Delmar, Cengage Learning
Brake Diagnosis and Undercar Checks
• Brakes that pull to one side – Causes: suspension or steering systems
• Brake pedal pulsation – Results when hydraulic pistons move during stop
– Brakes grab cause: oil or grease on lining
– Brake pull: several reasons
• Undercar checks– Perform a visual inspection of brakes with
vehicle raised on a hoist
© 2012 Delmar, Cengage Learning
Disc Brake Inspection• Disc brakes are inspected to see that a sufficient
amount of friction material remains on pads– Remove a front wheel and visually inspect pad
– Inspect the rotor
– Check rotor runout with a dial indicator
– Inspect rotor thickness and brake drums
– Inspect the caliper and wheel seals
– Test parking brake
– Inspect tubing and hoses
– Check for fluid leaks
© 2012 Delmar, Cengage Learning
Inspecting Drum Brake Assemblies
• Important steps– Remove and mark the brake drum
• Spray the flange area with penetrating oil• Use a hammer to rap on drum
– Inspect drum brake cylinders
– Inspect drum brake linings
– Check self-adjuster operation
© 2012 Delmar, Cengage Learning
Brake Fluid Service and Brake Fluid Testing
• Correct fluid to use is listed on reservoir– Space must be left to allow fluid expansion
• Fluid change interval– Change fluid every two years or 30,000 miles
• Brake fluid testing methods– Moisture content testers
– Refractometer testing
– Voltmeter testing
– Fluid test strips
© 2012 Delmar, Cengage Learning
Bleeding Brakes and Brake Bleeding Methods
• Air or moisture in system can result in soft pedal– Brakes are bled through a bleed screw
• Manufacturers specify bleeding sequences
• Brake bleeding methods– Manual bleeding and manual bleeding with a hose
– Pressure bleeding and vacuum bleeding
– Reverse fluid injection and gravity bleeding
• Several problems can occur during bleeding• Scan tool to may be required to cycle the ABS• Avoid contamination with petroleum products
© 2012 Delmar, Cengage Learning
Adjusting Brakes• Improper brake adjustments
– Cause a low, firm pedal
• Diagnosis– Pump pedal twice quickly to correctly diagnose
• Pedal height rises higher on second application: brakes need adjustment
– Most brakes today have self-adjusting mechanisms
© 2012 Delmar, Cengage Learning
Master Cylinder Service and Master Cylinder Removal
• Cover vent is obstructed– Air can be drawn in at back of master cylinder,
aerating fluid• Air in fluid causes a spongy pedal
– Check the vent when checking fluid level
• Removing master cylinder– Be sure to use fender covers
– Use a vacuum brake bleeder to empty fluid from master cylinder reservoir
• Then remove master cylinder
© 2012 Delmar, Cengage Learning
Master Cylinder Disassembly• Master cylinders
can be purchased as new or rebuilt– Bore of a cylinder
is corroded or pitted: cylinder must be replaced
• Quick take-up master cylinders are serviced in the same manner
© 2012 Delmar, Cengage Learning
Bench Bleeding the Master Cylinder
• Before installing a master cylinder– Fill with fluid and bleed air
• Quick take-up cylinder– Casting is larger near the rear
• Pedal free travel – Checked when master cylinder replaced
• Should be less than 1/8” of free play
© 2012 Delmar, Cengage Learning
Brake Job• Front or rear linings are replaced in pairs
– Consult the appropriate service manual
• Complete brake job includes:– All internal hydraulic parts of wheel cylinders and
disc calipers
– New brake fluid, hardware, and springs
– Drums and rotors may be remachined on lathe
• Ethics in brake work– Include disclaimer when incomplete brake job is
advertised
© 2012 Delmar, Cengage Learning
Drum Brake Lining Removal• Clean entire assembly before disassembling
brakes– Brake dust is dangerous to breathe
• Low-pressure wet brake washers are the most popular way of cleaning brake assemblies
• HEPA vacuum can also be used
• Removal of brake linings – Requires special tools
© 2012 Delmar, Cengage Learning
Rebuilding Hydraulic Cylinders• Hydraulic wheel cylinders and disc brakes can
be rebuilt if made of cast iron and not corroded– Two kinds of hone are available
• After honing: install new rubber parts
© 2012 Delmar, Cengage Learning
Reassembling a Wheel Cylinder and Removing Wheel Cylinders• Reassembling a wheel cylinder
– Lips on the wheel cylinder cups face toward fluid
– Use brake fluid liberally as an assembly lubricant
• Removing wheel cylinders– Pitted or corroded: must be replaced
– Use flare-nut wrench to remove brake tubing fitting
– Cylinder is held to backing by two screws or clip • Requires special service tool
© 2012 Delmar, Cengage Learning
Replacing Drum Brake Shoes• Important steps
– Clean backing plates• Use high-temperature lubricant on pads
– Inspect brake springs• Shoe return springs should not be loose or broken
– Service self-adjusters • Must be installed on the correct side of the car
© 2012 Delmar, Cengage Learning
Adjusting Drum Brake Clearance
• Initial clearance adjustment – Made before drums installed
• Brake adjusting gauge – Adjusted to size of drum
• Star wheel of adjuster – Turned until shoes expand to size of adjusting
gauge
• Manual adjustment – Can be done while the drum is installed
© 2012 Delmar, Cengage Learning
Drum and Rotor Service• Drum or disc lining
are replaced– Common practice:
remachine drums or rotors
• Too much metal must be removed: replace
© 2012 Delmar, Cengage Learning
Drum Service• Maximum amount that can be cut from most
drums is 0.060”– Typical larger drum lists a discard diameter that
is 0.090” larger than original
• Important points– Inspect drums to see that they are not out-of-
round or scored
– Be sure there is no oil or grease on drum
– Drums and rotors can be mounted on a lathe
– Tool bit at end of the cutter is a carbide insert
© 2012 Delmar, Cengage Learning
Rotor Service• Rotor in good condition
– Provides better surface than freshly machined • Rotors are always machined in pairs
• Machining a rotor– Cut both sides at once, maintaining equal force
on both sides
– Newly machined surfaces must be cleaned
© 2012 Delmar, Cengage Learning
On-Vehicle Rotor Machining• On-the-car brake lathes: becoming more popular
– Before reinstalling a brake rotor: clean any rust preventive material from surface
– Use a torque wrench when tightening lug nuts
© 2012 Delmar, Cengage Learning
Disc Brake Service• Important points
– Disc linings are usually easy to replace
– Most caliper designs require removal of caliper to remove pads
– Before you install replacement pads in a floating caliper, check the condition of its slides
– Open the bleed screw before retracting the piston
– All pistons must be compressed at the same time
© 2012 Delmar, Cengage Learning
Rear Disc Pad Installation and Rebuilt Calipers
• Rear disc pad installation – Rear-wheel disc brakes have a built-in parking
brake
– If there is a lever, do not force the piston into the bore
• Rebuilt calipers– Many shops find it more cost-effective to install
rebuilt calipers• Unloaded and loaded
© 2012 Delmar, Cengage Learning
Disc Caliper Rebuilding• Major steps
– Disassemble caliper
– Clean and inspect caliper parts
– Inspect the pistons
– Reassembly caliper
– Install disc pads in the caliper
© 2012 Delmar, Cengage Learning
Selecting Brake Linings• Various lining materials are available
– Depends on application and friction characteristics desired
• Older brake lining materials– Classified as organic or inorganic
• Side edge of a new brake lining – Stamped with code number established by SAE
• Aftermarket friction material certifications– Assure aftermarket lining performance
characteristics equal to or better than new cars
© 2012 Delmar, Cengage Learning
Disc Brake Noise• Brake noise and vibration
– Most likely complaints from a customer
– Important that disc linings be firmly attached
– Most pads have anti-rattle clips
– Metal-to-metal contact points must be lubricated to prevent noise
– Install caliper on correct side
– Today’s linings are more fully cured but still require some break-in
© 2012 Delmar, Cengage Learning
Parking Brake Cable Service• During a rear brake job
– Disconnect emergency brake cables from brake linings
– Wipe off cables and apply clean grease
• Brake cable requires replacement– Use small hose clamp to remove it from backing
plate
• Brake should be fully applied at half travel– Follow manufacturer’s recommendations
© 2012 Delmar, Cengage Learning
Vacuum Power Brake Service• Repairs to power boosters include replacement
of the hose, filter, or check valve• Causes of increased pedal effort
– Installation of larger diameter tires
– Defective power booster
• Vacuum booster operation test – Exhaust all vacuum reserve from power booster
• Power brake booster problems – Can be due to a hole in the booster diaphragm or
a stuck valve that is leaking
© 2012 Delmar, Cengage Learning
Vacuum Power Brake Service (cont’d.)
• Defective power booster – Causes brakes to drag
• Vacuum supply checks– Check hose that supplies vacuum to the power
booster from intake manifold
• Power brake booster problems – Hole in booster diaphragm or a stuck valve
• Typical power boosters – Have four studs that protrude through the
bulkhead into the passenger compartment
© 2012 Delmar, Cengage Learning
Brake Warning Lamp Diagnosis• Hydraulic safety switches
– Found on vehicles that do not have fluid level sensing systems
• Fluid level switches – Found on vehicles that do not have hydraulic
safety switch
• Check operation of stoplight switch– Apply brakes and verify that stoplights come on
– Use a wiring diagram to determine how the circuit operates
© 2012 Delmar, Cengage Learning
Antilock Brake System (ABS) System Service
• Covered in Chapter 59
Top Related