YUPO QUICK GUIDE

English ver.

HEAD OFFICEShin-Ochanomizu Building, 15th Floor, Kanda-Surugadai 4-3Chiyoda-ku, Tokyo 101-0062, JAPANPhone: +81-3-5281-0813 Fax: +81-3-5281-0819

KASHIMA FACTORY23 Towada, Kamisu-shi, Ibaraki 314-0102, JAPANPhone: +81-299-96-2931 Fax: +81-299-96-5099

* The contents of this catalogue are as of January 2017. Please note that it may be subject to change without notice for further improvement.* FGS150 is used (UV offset printing) * All Rights Reserved. * All photos are for illustrative purposes only.©2015 YUPO CORPORATION 1.2017 5,000 GM

http://www.yupo.com

KASHIMA FACTORY is registered "ISO 9001" (Registered NO.JCQA-0124) & "ISO 14001" (Registered NO.JCQA-E-00125)

“YUPO” is registered trademark of YUPO CORPORATION, Tokyo Japan.* Examples shown below are all our registered trademarks. * Part of the trademarks we hold is displayed.

ALPHAYUPOULTRAYUPO

YUPOSUPERYUPOYUPOTRACE

CLOTHYUPOHIGHTEAR YUPOYUPOJET

AQUAYUPOYUPOBLUEYUPO OCTOPUS

YUPO

’s Features

ChemicalsOil

High-quality paper YUPO®

Film YUPO®

Coated paper

YUPO®

MetallicTranslucentAdhesiveOil-based pen Pencil

4

Tougher than paper and more expressive than film.

YUPO is mainly made from polypropylene.

It does not contain wood pulp.

YUPO does not use chemicals that place a strain on the

environment, such as toxic heavy metals, accumulative toxins, and

ozone-depleting substances.

Protectingthe Air

Protectingthe Forest

Offcuts that are produced during the production process can be reused as raw material.

Trim Edgeare Reusable

The amount of CO2 emitted during production is about the same as that for conventional

paper, and less than film.

* If natural paper is compared with FGS 80* Calculated based on surface area

CombatingClimate Change

Used YUPO can be recycled as a refuse paper and plastic

fuel (RPF) for boilers, etc.

Becomes anEnergy Resource

Produced in a factory with ISO 14001 certification.ISO 14001 is the international standard for “Environmental Management Systems.” It requires continuous improvement of the environmental impact of business activities.YUPO CORPORATION obtained this certification for our Kashima factory and research and development laboratory in March 2000, and based on our environmental policy, we have been contributing to the local community and global environment through energy conservation, recycling, waste reduction, and prevention of contamination and accidents.

Making conventional paper requires vast amounts of clean water, but YUPO

requires very little water.

Protectingthe Water

Compared to paper…

Compared to film…

Environmentally friendly synthetic paper to protect the forest, the water, and the air.

3

YUPO was designed as a new-age paper product to replace conventional paper, which is made from wood pulp. It contributes to environmental conservation and reduced environmental impact in a number of ways.

YUPO is known for its water resistance, but that is not the only advantage it possesses. It has many other advantages over other synthetic paper, and this versatility is its greatest strength.

YUPO has exceptional water resis-tance, so it will rarely lose strength or become misshapen when wet.

Water resistant

Far tougher than paper in terms of stretching, folding, and shock resistance. Even tougher laminated products are available.

Tough

YUPO produces approximately 1/100 of the dust of high-quality paper. It hardly produces any dust, even when folded or abraded.

Clean (low dust)

Due to its special construction, which incorporates micro-voids (microscopic pores), YUPO is only 2/3 of the weight of coated paper of an equivalent thickness. It is so light, it floats.

Light (cushioned)

The surface is smooth, so it also provides a very attractive finish when used for lamination or other such purpose.

Smooth surface

There is almost no deterioration in quality when exposed to oils, acids, alkalis, or organic solvents, etc.

Oil and chemical resistant

YUPO is suitable for a range of printing methods, producing vibrant colors – just like paper.

Prints clearly

In addition to oil-based pens, some products can be written on with pencils. YUPO provides a smooth writing surface without sticking or slipping.

Suitable for handwriting

A range of unique products is available, such as adhesive products, translucent products, and metallic products. Products are also available in a range of calipers.

Many variations available

<Disposing of YUPO>・When discarding it as ordinary household waste, please dispose of it as the category of

plastic defined by the municipality of residence.・When disposing of it as waste at a business establishment, please treat it as industrial waste.

Product LineupProduct Lineup

16

YUPO comes in many product variations, so you can choose the best one for your use or printing method.

ULTRAYUPO™ SUPERYUPO™

Translucent

YUPOTRACE™YUPO™ Back Light

Thick

ALPHAYUPO™

Label

Face Stock for Sticker LabelEasy De-Laminate YUPO/Destructive YUPOAQUAYUPO™In Mold grade

Adhesive

YUPO OCTOPUS™YUPOSTATIC™

Laminated

CLOTHYUPO™YUPO™ MetalizedHIGHTEAR YUPO™YUPO™ 100% Opacity

For digital printing

YUPOJET™YUPOBLUE™ (Certified for HP Indigo)YUPO™ for UV silk screen/UV inkjet

Printing surface Both sides

Matte

Matte

○

○Oil-based pen

Pencil

Back

Front

Inferior to coated paper

Surface gloss

Suitability for hand-writing

Halftone reproduction

Printing method

Features of Standard Products

・ Oil-based offset printing (YUPO ink)・ UV offset printing・ Silk-screen printing・ Gravure printing

Both sides

Semi-gloss

Semi-gloss

×

○

Same level as coated paper

・ Oil-based offset printing (YUPO ink)・ UV offset printing　・ Silk-screen printing・ Gravure printing

Single side

Semi-gloss (Printing surface)

Matte

×

○

Same level as coated paper

・ Oil-based offset printing　(General-paper ink/YUPO ink)

This all-purpose product is available in a variety of calipers. It is not only suitable for oil-based offset printing, but also for UV offset printing.

This type dramatically shor tens the drying time of YUPO ink, allowing you to deliver the product earlier. There is almost no dot gain.

This product allows oil-based offset printing using general-paper ink. There is no need to switch to YUPO ink, and since drying time is short, you can deliver the product earlier. There is almost no dot gain.

Standard

15

YUPO is not difficult to convert if you are aware of the key points.

Technical Information

Product Lineup

The following pages contain notes on printing and processing as well as special features of each product’s specifications, etc.Please refer to the provided technical manual for detailed information.

* Edge-picking may occur

General YUPO (UV ink)

General YUPO (UV ink)

ULTRAYUPO™ SUPERYUPO™ Matte Semi-gloss Semi-gloss

Printing on YUPO

/Converting YU

PO

Delivery

Drying

Folding

Trimming

Wet Lamination/Dry Lamination

Punching (Die Cutting)

Perforation

Adhesive

Main Product List

20

▲

19

Printing method

・This all-purpose product is available in a variety of calipers.・Not only highly suitable for oil-based offset printing, but also UV offset printing.・Both front and back surfaces are matte.・Can be written on with pencil.・Ink setting takes 10-16 hours for a 4-color overlay (measurement example).

・This all-purpose product is used for a range of applications.・Suitable for oil-based offset and gravure printing.

・Fast drying time with YUPO ink.・The short drying time allows you to deliver the product earlier.・Color reproduction is exceptional, with minimal dot gain.・Both front and back surfaces are semi-gloss.・Ink setting takes 5-7 hours for a 4-color overlay (measurement example).* Edge-picking may occur in UV offset printing. Please contact us for further details.

・This product allows oil-based offset printing with general-paper ink.・Because there is no need to switch to YUPO ink, and the drying time is short, you can deliver the product earlier.・Color reproduction is exceptional, with minimal dot gain.・The front (printing surface) is semi-gloss and the back side is matte.・Ink setting time is less than 4 hours for a 4-color overlay with FRB (measurement example), and less than 4 hours for a 2-color overlay with FRR.* Only compatible with overlay of 2 colors or less when using FRR with ink for standard paper.

・This product is thin-type translucent.・It is used for items such as photographic screens and wrapping for frozen foods.・Can be written on.

・This product is translucent and was developed for illuminated signs.・Good light diffusion properties make images appear clearly when backlit.・BLR is suitable for designs with warm colors and BCR is suitable for designs with bluish-white colors.* Printing with HP Indigo is possible, but the water-resistant and ink adhesion is weak, so please use it for indoor applications.

・In-mold labels can be labeled at the same time as producing the bottle.・High-transparent type and no orange-peel properties.・Corona treatment is required before printing.

・This thicker product is available in many variations, including standard, ingle-side gloss, and translucent type.・Knife folding may cause breakage. Scoring and creasing is recommended instead.

・The reverse (adhesive surface) is a strong base for pressure-sensitive labels.・Strength between layers makes it suitable for removable labels.

・This product is for glued on labels and thermal labels.・The reverse absorbs water, so it is possible to use water-based adhesives.・Labels on containers can be removed cleanly, which is useful for garbage separation and recycling.* Edge-picking may occur in UV offset printing. Please contact us for further details.

・A pattern printed on the adhesive of the reverse side that remains on the surface to which the label was affixed after it is peeled off.

・The label tears apart when removed, leaving evidence of opening the product packaging.

General YUPO (UV ink)

General YUPO (Oxidation ink)

ULTRAYUPO™

SUPERYUPO™

YUPOTRACE™

YUPO™ Back Light

ALPHAYUPO™

ALPHAYUPO™ (Gloss type)

ALPHAYUPO™ (Translucent type)

Face Stock for Sticker Label

Face Stock for Sticker Label (TTR/Removable type)

Easy De-Laminate YUPO

Destructive YUPO

AQUAYUPO™

Product features & precautionsPrintingsurfaceGradeProduct name

Both sides

Both sides

Both sides

Single side

Both sides

Both sides

Both sides

Single side

Both sides

Single side

HP Indigo▲

Silk-screen printing/Gravure printing●

Silk-screen printing/Gravure printing●

Gravure printing●

Gravure printing●

Gravure printing/UV letterpress printing/

UV flexo printing

●

Silk-screen printing/UV letterpress printing

●

Silk-screen printing/UV letterpress printing

●

Silk-screen printing/UV letterpress printing

●

●：Appropriate　▲：Appropriate in some circumstances　Blank：Inappropriate

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

YUPO ink●

General-paper ink/YUPO ink●

Digital printingOther printingUV offset printingOil-based offset printing

CategoryStandard

TranslucentThick

For label

FGS 60, FGS 80, FGS 95FGS 110 , FGS 130, FGS 150 FGS 200, FGS 250, FGS 300

FEB 95, FEB 110, FEB 130FEB 150, FEB 200, FEB 250

FPG 60, FPG 80, FPG 95 FPG 110, FPG 130, FPG 150 FPG 200, FPG 250, FPG 300

FEBA 300

FRB 110, FRB 130

FRR 70

TPRA 60, TPRA 90

BLR 150

BCR 160

QJJ 350, QJJ 400, QJJ 500

QTYR 350

RMM 400

SGS 60, SGS 80, SGS 110

SGP 80, SGP 110

SAR 60

SLR 80

LAR 75, LAR 95

●

●

●

●

●

・In-mold labels can be labeled at the same time as producing the bottle.・Good for wide window-molding conditions.* Using the standard “FGS” product.

・In-mold labels can be labeled at the same time as producing the bottle.・Good for high-speed forming, wide window-molding conditions.

In Mold grade for Blow/Injection molding

In Mold grade for Injection molding

Single side

Single side

Both sides

Single side

Single side

Gravure printing●

Silk-screen printing/UV letterpress printing/

UV flexo printing

●

Silk-screen printing/Gravure printing●

UV letterpress printing/UV flexo printing

●

●

●

YUPO ink● ●

ITE 105

IDF 80, IDF 100

IHC 75

LBR 80

UAIB 80

FGS 80

・In-mold labels can be labeled at the same time as producing the bottle.・Good for high-speed forming, wide window-molding conditions and anti-static properties.

・In-mold labels can be labeled at the same time as producing the bottle.・No orange-peel properties.

・In-mold labels can be labeled at the same time as producing the bottle.・Transparent type and no orange-peel properties.

・In-mold labels can be labeled at the same time as producing the bottle.・No orange-peel and wide window-molding conditions.

▲(Low energy UV lamp recommended)

▲(Low energy UV lamp recommended)

Main Product List

ISF 105

Main Product List

Main Product List

2221

・This product is ideal for HP Indigo digital printers.・Double-sided printing is possible without pre-coating. High water resistance and rubbing resistance.・It is suitable for a range of printing methods, from HP Indigo digital printing to various types of UV printing.* Please consult us for further details.

・This product is 100% opaque for complete black-out effect.・Suitable for double-sided printing as there is no see-through.

・This product is laminated with YUPO and cloth (synthetic fiber).・Exceptional toughness makes it suitable for processes such as machine sewing and wire threading.・It is appropriate for large printed materials, such as hangings and cloth banners.

・This product is suitable for wide-format inkjet printers.・Unlike paper, it does not swell due to humidity or ink. Because it is tear-resistant, you can print with confidence on large sheets.* Please enquire about the many other types we produce.

・This product is laminated with YUPO and non-woven fabric.・Exceptional toughness makes it suitable for processes such as machine sewing and wire threading.・Traditional Japanese paper texture.

・This product is suitable for UV inkjet printers.

・This product is laminated with metalized PET.YUPO™ Metalized

HIGHTEAR YUPO™

YUPO™ 100% Opacity

YUPOBLUE™ (Certified for HP Indigo)

YUPO™ for UV silk screen/UV inkjet

CLOTHYUPO™ (Laminated with synthetic woven cloth/single side)

YUPOJET™ Single side

Single side

Both sides

Both sides

Both sides

Both sides

Both sides

Both sides

Inkjet printers (Water-based pigment ink)●

Inkjet printers (Water-based dye or pigment ink)

●

Inkjet printers (Eco-solvent ink)●

UV inkjet printers●

UV inkjet printers●

UV silk-screen printing●

UV inkjet printers●

HP Indigo/Thermal transfer●

UV inkjet printers●

YUPO ink●

Silk-screen printing●

YUPO ink/Use ink for aluminum foil

(metallic finish surfaces only)

●

YUPO ink●

YUPO ink●

YUPO ink● ● UV letterpress printing/

UV flexo printing/UV form offset printing, etc.

●

UV silk-screen printing●

WNF 135

VJFP 120, VJFP 170, VJFP 190

WCFA 125, WCFA 195

WSF 110, WSF 160

YPI 150, YPI 200YPI 250, YPI 300

FPU 130, FPU 200, FPU 250

WMF 120

・This micro-suction sheet can be stuck to smooth surfaces and then removed and reused, even multiple times.・Easily adheres to surfaces while excluding air.・Because adhesive is not used, no residue is left on the surface after removal.・If the adhesive surface becomes dirty, rinse off the dirt with water and then dry it to restore the adhesive properties.* Printing is not possible on the adhesive side.* Cannot be used for car stickers or on wired glass.* Not suited to outdoor uses.

・This sheet uses static electricity to adhere to surfaces.・It can stick to uneven surfaces such as walls.・Because adhesive is not used, no residue is left on the surface after removal.* When peeled off once, the material loses some of static electricity power, so it cannot be reused multiple times.* Not suited to outdoor uses.

YUPO OCTOPUS™ (Offset ink) WKFS 340

WKJ 250

WKE 250

XAD 1058

XAD 1068

XAD 1069

WESC 165

WEJ 200

WESA 165

Single side

Both sides

Single side

Both sides

HP Indigo●

Inkjet printers (Eco-solvent ink)●

Inkjet printers (Water-based pigment ink)●

General-paper ink/YUPO ink●

HP Indigo●

Inkjet printers (Water-based dye or pigment ink)●

●

●

●

YUPO OCTOPUS™ (Inkjet ink)

YUPO OCTOPUS™ (HP Indigo)

YUPO OCTOPUS™ (Clear)

YUPO OCTOPUS™ (UV silk screen/UV inkjet)

YUPOSTATIC™ (Offset ink/UV inkjet)

YUPOSTATIC™ (Inkjet ink)

YUPOSTATIC™ (HP Indigo)

Main Product List

Printing methodProduct features & precautionsPrinting

surfaceGradeProduct name

●：Appropriate　▲：Appropriate in some circumstances　Blank：Inappropriate

Digital printingOther printingUV offset printingOil-based offset printing

CategoryStick type

Laminated

For digital printing

CLOTHYUPO™(Laminated with synthetic woven cloth/double side)

XAB 1020

WNFW 200

VJFN 160

Stock List/YUPO’s m

anufacturing process and structure

2423

General YUPO (Oxidation ink)

General YUPO (UV ink)

ULTRAYUPO™

SUPERYUPO™

YUPOTRACE™

YUPO™ Back Light

ALPHAYUPO™

ALPHAYUPO™ (Gloss type)

ALPHAYUPO™ (Translucent type)

AQUAYUPO™

In Mold grade for Blow/Injection molding

In Mold grade for Injection molding

YUPO OCTOPUS™ (Offset ink)

YUPO OCTOPUS™ (Inkjet ink)

YUPO OCTOPUS™ (UV silk screen/UV inkjet)

YUPOSTATIC™ (Offset ink)

YUPOSTATIC™ (Inkjet ink)

YUPOSTATIC™ (HP Indigo)

YUPO™ 100% Opacity

YUPOJET™

YUPOBLUE™ (Certified for HP Indigo)

YUPO™ for UV silk screen/UV inkjet

Sheets per package Roll sizeRollSheet productsGradeCategory Product name

FPG 60

FPG 80, FPG 95, FPG 110, FPG 130, FPG 150

FPG 200, FPG 250, FPG 300

FGS 60

FGS 80, FGS 95, FGS 110, FGS 130, FGS 150

FGS 200, FGS 250, FGS 300

FEB 95, FEB 110, FEB 130, FEB 150

FEB 200, FEB 250

FEBA 300

FRB 110, FRB 130

FRR 70

TPRA 60

TPRA 90

BLR 150

BCR 160

QJJ 350, QJJ 400, QJJ 500

QTYR 350

RMM 400

VJFP 120, VJFP 170, VJFP 190

XAB 1020

VJFN 160

YPI 150

YPI 200, YPI 250, YPI 300

FPU 130, FPU 200, FPU 250

WNF 135

WNFW 200

WMF 120

WSF 110, WSF 160

WCFA 125

WCFA 195

WKFS 340

WKJ 250

WKE 250

XAD 1058

XAD 1068

XAD 1069

WESC 165

WEJ 200

WESA 165

●

●

●

●

●

●

●

●

●

●

●

500

250

125

500

250

125

250

125

125

250

250

●

●

●

●

500

250

250

250

●

●

●

●

●

●

●

●

100

100

100

●

●

●

●

●

●

●

●

●

●

●

100

250

250

250

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

●

125

100

100

250

125

250

250

250

250

250

250

250

250

125

●

●

●

●

●

●

●

●

●

●

●

*Consult us for special-size orders.

StandardTranslucent

ThickFor label

Stick typeLam

inatedFor digital printing

YUPO’s unique production method is patented around the world.YUPO is made up of 3 layers. The base layer is stretched both lengthwise and crosswise, while the surface layer is stretched crosswise (bi-axially oriented film forming process). This production method is only possible because of our unique technology, which is protected by patents around the world, including in Japan, America, and China.

❶Extruder

❷Extruder

❸Extruder

Raw material(polypropylene)

Additives

Pelletizing

Pellets

Surface layer

Base layer

Stretched in machine directionMaterial expelled from the extruder is stretched in the machine direction using rollers to form the base layer.

2 Stretched in cross directionThe base layer is laminated on each side with the surface layer, and is then stretched in the cross direction.

3

Producing pelletsPellets are made by adding inorganic filler and additives to polypropylene.

1

Surface layer

Trimmed edges produced during the production process can be reused as raw material.

YUPO’s StructureStrength comes from the base layer, while the paper-like characteristics come from the surface layers.YUPO is a synthetic paper made up of 3 layers: a base layer and a surface layer laminated to each side. The base layer gives YUPO strength, while the stretching process provides the surface layers with innumerable micro-voids (microscopic pores), which make it very white, as well as lightweight and suitable for handwriting.

Machine direction(MD)

Cross direction (CD)

Surface layer

Surface layerBase layer

Check YUPO’s grain. The grain direction has double the stiffness.Just like paper, YUPO has a grain. The grain runs along the first dimension listed in the label, so make sure you check this before use. Many YUPO sheets have a short grain; however some products that are prone to fanning out (inaccurate registration) have a long grain.

For uses that require stiffness, such as swing POPs, make sure the grain is aligned with the curve. The stiffness in the direction of the grain has twice that of the grain.

788×1,091mm

Micro-voids

YUPO’s grainYUPO’s grain

■Grain direction of roll products ■Grain direction of sheet products

YUPO’s grain

POP shape

Curve

YUPO

’s grain

1,000mm×3,000m

High stiffnessLow stiffness

Example Example

Face Stock for Sticker Label

Easy De-Laminate YUPO

Destructive YUPO

SGS 60, SGS 80, SGS 110

SGP 80, SGP 110

SAR 60

SLR 80

LAR 75

LAR 95

ITE 105

ISF 105

IDF 80

IDF 100

IHC 75

LBR 80

UAIB 80

610x20m, 914x20m, 1,270x20m

1,270x20m

1,270x20m

1,240x50m

1,240x50m

914x30m, 1,270x30m

610x30m, 914x30m, 1,270x30m

1,370x30m

Stock List YUPO’s Manufacturing Process

YUPO™ Metalized

HIGHTEAR YUPO™

CLOTHYUPO™(Laminated with synthetic woven cloth/single side)CLOTHYUPO™(Laminated with synthetic woven cloth/double side)

Face Stock for Sticker Label (TTR/Removable type)

YUPO OCTOPUS™ (HP Indigo)

YUPO OCTOPUS™ (Clear)

Physical Properties

2625

＊WESC 165 has a transparent face with a YUPO backing.

・Caliper: Range from 60 μm (0.06 mm) to 500 μm (0.5 mm).・Density: The density of most products is below 1 g/c㎥. They are light enough to float on water.・Whiteness: The greater the value, the whiter the product.・Opacity: Products for which the value is 100% are completely opaque.・Gloss: The greater the value, the glossier the printing finish.・Tensile strength: This is the maximum load that can be applied to the MD (machine direction) and CD (cross direction).・Elongation: The amount of elongation that will occur before giving way when stretched.

* Values are representative examples of measurements taken by YUPO. We do not guarantee the accuracy of stated values.* Tests were conducted according to the standards listed.* The optical system used to test opacity is compliant with JIS Z 8722.

・Clark stiffness: The greater the value, the greater the stiffness.・Surface resistance: The lower the value, the less generation of static electricity. (PP has more than 1015

16

17

17

17

17

17

16

15

15

16

17

17

17

18

18

19

19

19

49

50

48

49

48

46

46

53/24

53/24

49/21

13

15

15

34

20

20

19

89/18

13

22/54

22/53

22/52

4/6

6/7

36/26

38/26

3

4

6

6

7

8

10

10

9

3

4

5

6

7

8

10

10

9

5

6

7

7

10

10

10

4

5

3

4

6

10

10

–

–

–

–

–

3

5

6

5

6

3

5

9

10

15

15

20

20

30

35

35

7

10

15

15

20

20

30

35

35

15

15

20

20

30

35

35

15

15

10

9

15

30

30

–

–

–

–

–

10

15

20

15

20

10

15

115

125

125

130

130

140

155

165

130

115

130

130

135

135

135

150

160

130

130

125

130

135

135

120

100

90

95

120

185

200

210

200

–

–

–

–

–

120

125

130

125

130

115

125

30

30

25

25

25

25

30

30

30

25

30

30

30

30

30

30

30

30

30

30

30

25

25

30

30

30

30

25

40

40

40

35

–

–

–

–

–

25

25

25

25

25

25

25

15

20

30

40

55

70

125

200

270

15

20

30

40

50

65

125

195

270

35

45

60

75

130

210

280

45

60

20

15

30

80

95

300<

300<

300<

300<

300<

10

20

35

20

35

15

30

25

40

60

80

110

145

255

300<

300<

20

30

45

65

90

125

230

300<

300<

65

85

115

155

270

300<

300<

80

110

35

15

40

130

170

300<

300<

300<

300<

300<

25

50

90

50

90

35

55

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1010

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

1×1011

60

80

95

110

130

150

200

250

300

65

80

95

110

130

150

200

250

300

95

110

130

150

200

250

300

110

130

70

60

90

150

160

350

400

500

350

400

60

80

110

80

110

75

95

47.4

61.6

73.2

84.7

100.1

115.5

158.0

200.0

234.0

51.4

61.6

73.2

84.7

100.1

115.5

158.0

200.0

234.0

73.2

84.7

100.1

115.5

158.0

200.0

234.0

88.0

102.7

56.7

60.6

91.8

153.0

153.0

340.0

390.0

494.0

353.0

396.0

48.6

66.4

91.3

66.4

91.3

60.8

76.5

0.79

0.77

0.77

0.77

0.77

0.77

0.79

0.80

0.78

0.79

0.77

0.77

0.77

0.77

0.77

0.79

0.80

0.78

0.77

0.77

0.77

0.77

0.79

0.80

0.78

0.80

0.79

0.81

1.01

1.02

1.02

0.96

0.97

0.98

0.99

1.01

0.99

0.81

0.83

0.83

0.83

0.83

0.81

0.81

96

96

96

96

96

96

96

96

96

97

97

97

97

97

97

97

96

96

98

98

98

98

98

98

97

98

98

98

92

92

93

94

95

95

95

93

93

97

97

97

97

97

98

98

87

90

92

94

95

96

98

99

99

87

91

93

95

96

96

98

99

99

96

97

98

98

99

99

99

96

97

91

30

40

63

63

98

98

98

96

78

85

89

93

89

93

95

96

Gloss (%) Tensile strength (kN/m)

MD CD

Elongation (%)

MD CD

Clark stiffness (S value)

MD CD MD CD MD CD MD CD

Thickness(μm)Grade Basis weight

(g/㎡)Density(g/㎥)

Whiteness(%)

Opacity(%)

Specific surface resistance ( )

Gloss (%) Tensile strength (kN/m) Elongation (%) Clark stiffness (S value) Thickness(μm)Grade Basis weight

(g/㎡)Density(g/㎥)

Whiteness(%)

Opacity(%)

Specific surface

Front: 1×1012

Back: 1×1011

Front: 1×1012

Back: 1×1015

Front: 1×1012

Back: 1×1015

Measurementmethod

Measurementmethod

JIS P 8118

JIS P 8124

JIS P 8118

JIS L 1015

JIS P 8149

JIS P 8142

JIS P 8113

JIS P 8113

JIS P 8143

JIS K 6911

FPG 60

FPG 80

FPG 95

FPG 110

FPG 130

FPG 150

FPG 200

FPG 250

FPG 300

FGS 60

FGS 80

FGS 95

FGS 110

FGS 130

FGS 150

FGS 200

FGS 250

FGS 300

FEB 95

FEB 110

FEB 130

FEB 150

FEB 200

FEB 250

FEBA 300

FRB 110

FRB 130

FRR 70

TPRA 60

TPAR 90

BLR 150

BCR 160

QJJ 350

QJJ 400

QJJ 500

QTYR 350

RMM 400

SGS 60

SGS 80

SGS 110

SGP 80

SGP 110

LAR 75

LAR 95

19/52

24/65

25/65

25/65

64/85

55/14

59/19

–

–

–

–

101

17

109/15

2/18

16/16

17/5

17/17

100</16

10/16

10/17

16

18

2

2/17

2/17

37/16

11/10

13/11

14/12

14/11

17

17

16

4

4

4

5

6

4

–

–

–

–

–

–

–

–

–

–

9

12

8

4

7

7

10

–

–

–

–

8

10

10

9

7

10

10

10

10

15

15

20

10

–

–

–

–

–

–

–

–

–

–

16

25

18

8

16

19

25

–

–

–

–

20

30

35

35

20

30

35

140

140

165

170

180

150

–

–

–

–

–

–

–

–

–

–

51

56

105

80

125

135

150

–

–

–

–

140

150

160

130

140

155

165

20

20

30

30

30

30

–

–

–

–

–

–

–

–

–

–

23

26

23

18

21

33

26

–

–

–

–

30

30

30

30

30

30

30

15

15

15

20

15

15

11

–

–

–

–

–

–

–

–

–

44

13

68

13

33

46

109

–

–

–

–

65

120

180

300

50

130

200

45

45

25

45

35

30

–

–

–

–

–

–

–

–

–

–

59

205

107

23

72

89

210

–

–

–

–

125

230

300<

300<

110

260

300<

–

–

–

1×1011

–

–

1×1010

1×1011

9×1011>

9×1011>

9×1011>

9×1011>

9×1011>

9×1011>

9×1011>

–

–

–

–

1×1010

1×1010

1×1010

1×1010

1×1011

1×1011

1×1011

107

107

81

101

77

80

87

320

220

245

210

178

210

162

200

164

134

201

123

107

159

123

190

115

165

135

160

150

200

250

300

130

200

250

81.6

82.7

75.2

92.0

68.8

66.4

72.1

220.0

156.0

175.0

170.0

235.0

166.0

143.0

160.0

140.0

101.2

155.0

106.3

70.0

110.0

104.0

150.0

78.0

117.5

90.0

135.0

115.5

158.0

200.0

234.0

100.1

158.0

200.0

0.76

0.77

0.93

0.91

0.90

0.83

0.83

0.69

0.71

0.71

0.78

1.30

0.79

0.88

0.80

0.87

0.75

0.78

0.86

0.65

0.65

0.83

0.82

0.68

0.71

0.67

0.84

0.77

0.79

0.80

0.78

0.77

0.79

0.80

97

97

96

96

90

96

–

97

97

90

96

–

96

90

93

96

96

96

–/95

96

95

88

91

96

101

92

97

97

97

96

96

97

97

97

94

94

86

91

14

85

11

97

95

96

93

–

–

3/97

95

87

60

96

100

88

94

100

100

–

93

95

96

96

98

99

99

96

98

99

JIS P 8118

JIS P 8124

JIS P 8118

JIS L 1015

JIS P 8149

JIS P 8142

JIS P 8113

JIS P 8113

JIS P 8143

JIS K 6911

ITE 105

ISF 105

IDF 80

IDF 100

IHC 75

LBR 80

UAIB 80

WKFS 340

WKJ 250

WKE 250

XAD 1058

XAD 1068

XAD 1069

WESC 165

WEJ 200

WESA 165

WNF 135

WNFW 200

WMF 120

WSF 110

WSF 160

WCFA 125

WCFA 195

VJFP 120

VJFP 170

XAB 1020

VJFN 160

YPI 150

YPI 200

YPI 250

YPI 300

FPU 130

FPU 200

FPU 250

Front: 1×1011

Back: 1×1015

Front: 1×1011

Back: 1×1011

Front: 1×1012

Back: 1×1011

Back: 9×1013>

Front: 1×1011

Back: 1×1013

Front: 1×1011

Back: 1×1015

Front: 1×1011

Back: 1×1015

Front: 1×1015

Back: 1×1015

Physical Properties (General Properties of Each Product)

Front/BackFront/Back