Your bucket tooth - Plasterer Equipment Company Deere Bucket Tooth... · Your bucket tooth...

Your bucket toothinformation source includingproduct features,applicationsand specifications for thefollowing product lines:��Fanggs��Deere��Caterpillar replacement��Hensley replacement��Esco Conical replacement��Esco Super��Esco Helilok�/Vertalok��H & L replacement��Rippers and scarifiers

Bucket Tooth Basics

Basics1

Tooth Performance and Wear Life

Maximum performance and wear life are the twomost important characteristics for replacementteeth. Working with constant abrasive materialplaces extreme demands on both design andstrength.

Design is directly related to performance whilestrength is directly related to wear life.

Tooth Penetration

Penetration is a key design consideration for allreplacement teeth.

To achieve good penetration, a tooth must have asharp point for initial ground entry.

The tooth blade must taper gradually enough toreduce resistance to penetration and yet be thickenough to avoid breakage.

The easier it is to penetrate the material…the lesshorsepower is required for operation.

Tooth Centerline vs. Non-Centerline Design

All centerline points are reversible to distribute wear and stay sharp.

Non-centerline points can be rotated to balance wear patterns, but they cannot be “flipped over” toresharpen.

Tooth Performance and Wear Life

Design = Performance

Strength = Wear Life

The best designed tooth is always a compromise of performance and wear life.

To Achieve Good Tooth Penetration

1. Tooth must have sharp point.

2. Blade must taper gradually to reduceresistance.

3. Blade must be thick enough to avoidbreakage.

PI7262 Litho in U.S.A. (97-02)

Tooth InstallationThe job of a tooth retainer is to withstandimpacts or shocks transmitted through the toothwithout breaking or falling out. It must alsotake up manufacturing tolerances so the toothstays tight on the adapter.

The various types of “hardware” to install teethare covered in detail within each section. Theseare some types of hardware or retainers used:

Flex PinSpring PinHorizontal Pin and Split WasherRoll PinGroove PinCrimp-OnPin and LockQuadrilok®

Pin and Plug

Tooth WearIt is a good idea to inspect bucket teeth,adapters, and the bucket condition daily. Bydetermining wear patterns and rotating teeth,you can extend wear life and increaseproductivity which, in turn, provides you thegreatest return for the money invested.

When using the right tooth and operating thebucket according to standard practice, a patternwill develop for normal wear. The tooth willmaintain a profile similar to the original profileand it will continue to penetrate materialquickly and easily.

But even when using the right tooth, toothwear is seldom even. Teeth that are near bucketcorners generally wear fastest. And a bucketthat is regularly loaded at an angle will showuneven wear on the loading side. Rotatingteeth will help equalize the wear.

While teeth could assume the shape of a fistdue to improper use of the bucket such asscraping, dragging, or banging, it is most likelythat the wrong teeth are being used for theapplication. Using the wrong teeth for theapplication takes more power to penetratematerial and reduces productivity.

Tooth BreakageTooth wear is expected, but tooth breakageunder normal working conditions is not!

Tooth breakage in extreme conditions - veryhard abrasive material where blasting, ripping,or air hammering might be more effective -should be expected.

The worst thing an operator can do is use thebucket with missing teeth. A missing toothexposes the adapter nose piece to wear. Anyamount of worn metal from the adapternosepiece leaves an open pocket between theadapter and the replaced tooth. This open areaallows the tooth to work back and forth. Theadapter can no longer provide the supportnecessary to firmly attach the tooth to thebucket. To find out if the nosepiece is thereason for the tooth breakage, remove the toothtip. If the nosepiece is worn, the original shankor adapter should be replaced.

Both abnormal wear and breakage can beprevented with the right choice of teeth. Somesuggestions include reducing the size andlength of the point or switching to a forged orcast tooth when material becomes harder andmore abrasive.

Bucket Tooth Basics (Continued)

Basics2PI7262 Litho in U.S.A. (97-02)

Bucket Tooth Basics (Continued)

Basics3

Tooth Position

FANGGS teeth have a curved shape to extend the contour of the bucket which results in a continuousflow of material to achieve maximum bucket fill. Reversing Fanggs teeth so that the curve of thetooth is opposite that of the bucket is not recommended.

Teeth other than Fanggs installed on backhoeand excavator buckets are mounted asindicated in the above illustration. The flat areaof the tooth faces the open part of the bucket.In this position, tooth entry into the ground isvery aggressive. It allows the teeth to breakmaterial for easier bucket loading. It isrecommended that teeth be mounted in thisposition for normal digging conditions.

Forged and cast backhoe and excavator teethcan be reversed as shown in this drawing. Theflat of the tooth faces away from the open sideof the bucket. As you can see, tooth angle isless aggressive. Teeth can be mounted in thisposition to avoid disturbing the trench floor.

It is not recommended that fabricated teeth bemounted in this reversed position. As thebucket is being loaded, material will wear thinthe clip portion of the tooth. Eventually, toothbreakage will occur. The clip is made of asofter metal and as a result is more susceptibleto wear than the blade portion of the fabricatedtooth.


Adapter Installation

Basics4

Bolt-On Adapters

When installing a new adapter, be sure thecutting edge provides a firm mounting base. Ifthe edge has been worn and doesn’t providesupport, the adapters are susceptible tobreakage.

Always use the attaching hardwarerecommended for the application. Bolt tensilestrength has been matched to specificapplication requirements.

Weld-On Adapters

Warning: Persons performing welding andother maintenance work should wear OSHA-approved safety equipment such as hard hats,safety shoes and glasses, work gloves, and theproper lenses in welding gear.

When welding adapters to the bucket cuttingedge, make sure the cutting edge provides afirm mounting base. This support is necessaryas adapters are also susceptible to breakage.Welding to the bucket cutting edge may causecracks in the cutting edge if a firm mountingbase is not provided and good weldingtechniques are not followed:

1. Remove the tooth and pin from the adapterprior to welding. High weldingtemperatures can have a detrimental effecton tooth heat treatment.

2. Clean the area to be welded. Remove paintby sanding or grinding. Remove oil andgrease using a safe solvent. Remove rustand dirt using a wire brush.

Various retention methods between the adapter and bucket as well as the tooth and adapter areavailable.

Check the condition of the bucket and repair as necessary before installing an adapter.

3. On hydrostatic crawler loaders, preheatthe cutting edge holes (second set fromeach end) to 400˚F (204˚C).

4. Use a temperature stick (Tempilstik orequivalent) to check preheat temperature.

5. Fill the holes with plug welds.

6. Grind weld flush with top cutting edgesurface.


Adapter Installation (Continued)

Basics5

7. Tack weld the rear of the adapter to thecutting edge.

8. Preheat adapter to 400-600˚F (204-306˚C) before welding. Use atemperature stick to check for correcttemperature.

9. Use a smaller diameter (0.12″ (3 mm)maximum) electrode to make the J-groove welds with an unequal leg filletweld (2). Extend the longer leg onto thecutting edge.

10. Start at the rear of the adapter. Weld onepass to 1″ (25.4 mm) from the edge (4).Weld one pass on the other side of theadapter.

11. Chip off the slag and peen each weldbead after each pass. Alternate from oneside of the adapter to the other side foreach pass.

12. After all adapters are welded, uniformlyheat the edge and all adapters to 400˚F(204˚C). Let the adapters and cuttingedge cool slowly in still air.


Manufacturing Process

Basics6

ADI Teeth

Austempered ductile iron teeth are used on backhoes, excavators and loaders. They offer moderateto heavy impact resistance. An ADI tooth is essentially a cast tooth of different chemistry, ductileiron which is brought to heat in a controlled environment (austempering). John Deere has a videooffering further explanation of ADI (DGVHI93821 available from DSC).

The manufacturing of ADI teeth starts naturallywith an engineering drawing of the part itself.

From the drawing, critical dimensions areutilized to machine a metal pattern.

The pattern is then used to manufacture proto-type castings. These are evaluated byengineering to confirm the design. If anypattern adjustments are required, additionaltooth samples are produced and final approvalauthorized.

The pattern forms the outside shape of thetooth. It incorporates the gating system whichis the path the molten metal flows through tothe actual tooth cavities.

Although the pattern forms the outside shapeof the tooth, the pocket area is formed by acore. The core is produced in a metal machinedcore box. The box is injected under pressurewith a resin-coated sand.

By using heat, the resin-coated sand grainsbond together forming a shell core. The shellcore is dipped into a liquid metal protectantwhich provides a smooth pocket and accuratepin hole location.

The pattern is then mounted on an automaticmolding machine. This machine takespreconditioned sand that has been mixed withclay and water and compresses the sand againstboth sides of the pattern plate to form the twohalves of the mold. These two halves of themold are pulled away from the pattern leavingdetailed impressions in the sand. Then the shellcores are strategically placed into the imprint.Now the two halves are joined forming thecasting impression.

The molds are next transferred by conveyor tothe mold handling system. A metal jacket isplaced around each mold to insure that no sidemovement occurs between the mold halves.The weight is set on top of the mold to applyadditional pressure so that no separation occursas the pouring process is completed.

The combination of the following metalsprovide high strength and ductility:

• Pig iron• Manganese• Steel• Along with other alloys including

carbon and silicon

All of these materials have the necessarymetallurgical chemistry to meet John Deere’sstrict specifications.

This raw material is carefully weighed so thatthere is a consistent cross match of ongoing,solid, raw material with an outgoing moltenductile iron.

The charge vessel is moved in place over theelectrical furnace and material is released.After approximately 15 minutes, the materialwill be heated to about 2700 degreesFahrenheit and will be transformed into aliquid state.


Manufacturing Process (Continued)

Basics7

ADI Teeth (Continued)

The metal undergoes chemistry analysis tomonitor quality standards.

The iron is then poured into an inoculationladle, magnesium is added, and it is thentransferred to the pouring area.

The iron pourer will check the molten iron forproper pouring temperature and magnesiuminoculations. If the material passes inspection,molds are poured. The metal travels throughthe gating and fills each tooth cavity.

Once poured, the carousel moves the mold tothe cooling chamber for a specified time.Afterwards the teeth are removed mechanicallyand pass down the shake-out area. Thisremoves the majority of sand from the casting.

The castings are now transported to thetumble-blast area for final cleaning.

They are shuttled to a grind step to remove theend gates and any protrusions.

Quality assurance and analysis occursthroughout the processes. Constant monitoringof the sand and metal micro structure ensure ahigh quality casting.

Spectrographic analysis is also constantlyperformed to provide proper metal chemistries.

Inspection steps continue as Brinell Hardnessand additional quality audits are consistentlyadministered.

In final process, the castings undergo anaustempering heat treatment. This makes thefinal product stronger, harder, tougher.

Cast Teeth

Cast teeth are used on loaders, scrapers,rippers, and scarifiers. They are formed from amedium-carbon, chromium, nickel,molybdenum steel offering high strength andtoughness with deep-hardening properties.They have excellent resistance to wear andabrasion.

The manufacturing process begins with thepattern which is basically an exact duplicate ofthe tooth to be cast but slightly oversized tocompensate for steel contraction. The mold ismade from this pattern.

The mold consists of silica sand and binder. Itcontains the cavity into which the molten metalwill be poured in order to form the casting. Themold is made in two sections with the top halfreferred to as the cope and the bottom as thedrag.

The core is also made of a sand mixture. Whenplaced in the mold, it forms the tooth pocketarea. At this point, liquid cement is applied tothe cope and drag. Clamping fixtures press thetwo pieces together.

Metal is placed into the furnace for the meltprocess. The melt process begins as three, 8-inch (203 mm) diameter graphite electrodesmoving in tanden work their way downwardthrough the charge. An electric arc ismaintained between the electrodes and thecharge. When the electrodes reach the bottom,the initial transformation to liquid steel takesplace. The entire charge is then transformedinto liquid steel as the electrodes slowly returnupward. At this point, the temperature of thesteel is approximately 2900˚F (1593˚C).

Following the adjustments dictated by steel andslag samples taken to determine carbon leveland stage of melt process, the melt is refined.Temperature is raised to 3200˚F (1760˚C), andtested again to determine if alloy adjustmentsare necessary. The entire melt is then pouredinto a tapping ladle, reladled into small pouringladles, and poured into the mold.


Basics8


Cast Teeth (Continued)

After cooling, the teeth are run through ashakeout to remove the mold and cores.Castings go through an additional cleaningoperation to remove all sand. Using acetylenetorches, excess material is removed from theteeth which then go through a finishing grindto remove all excess metal.

All John Deere cast teeth are differentiallyheat-treated to provide the hardness, wearresistance, and toughness for the longest, mostproductive life.

Forged Teeth

Forged teeth are used on backhoes, loaders,excavators and motor graders.

Chrome-moly alloy steel along with thecontinuous fibre structure and grain flow of thesteel provide increased strength whilemaintaining hardness. Forged teeth have a hightensile strength while maintaining excellentductility.

Forged teeth are produced from steel bars andbillets with specified and carefully controlledanalysis. The raw material is cut to size andheated in electric induction heating units toforging temperatures. Electrical heatingprovides a much higher quality product than gas heating.

Following heating, the part undergoes up to tensteps in the forging process to form the toothfrom the solid steel billet. After forging, theindividual parts are inspected, hand finished,and then sent on to heat-treating.

In the heat-treating process, the teeth areindividually placed in containers to providethorough and even heating. Next, they areloaded into endothermically-controlledatmosphere furnaces where they are heated to aclosely controlled temperature. This type offurnace allows the surface chemical analysis ofthe part to be maintained and ensures that thepart will be heat-treated to the maximumattainable hardness. Following the hardeningprocess, the teeth are tempered and inspectedfor hardness.



Basics9

Fabricated Teeth

Fabricated teeth are used on backhoes,excavators, and motor grader rippers. They arestandard-duty teeth which are self-sharpeningand feature easy replacement and economy.

Two pieces - the blade and the clip - comprisethe fabricated tooth. Since the blade incursmost of the wear, it is made of chrome-nickel-moly alloy steel heat-treated to Rockwell C45-50. The clip is shaped to form the exact pocketsize required for precise adapter fit. It iselectronically welded to the blade and thenheat-treated and tempered.

Nodular Iron Teeth

Nodular iron teeth are available on utilitycrawler loaders. These teeth are a one-piece,bolt-on type. They are generally used in light-duty applications.


Hardness Testing

Basics10

Charpy Test (Impact Stronger)

A test bar (a small metal bar from a pourapproximately 6” long) is notched and placedon the anvil. The hammer portion of the testingmachine is released with adequate force tobreak the sample. The scale measures theenergy absorbed by the sample during thefracture. The farther the pendulum swingsthrough the sample, the more brittle thematerial.

John Deere’s charpy range is from 17-19 whichindicates excellent impact strength.

Brinell Hardness

The Brinell Hardness Number (BHN) is one ofthe oldest tests and is the most commonstandard. The tooth is placed on the anvil and asteel ball is pressed into the sample with a loadof 3000kg. The load is then left in place for 30seconds and then removed. The diameter of theimpression is then read in millimeters with alow power microscope with a measuringeyepiece and the BHN is determined.

The BHN in John Deere’s product line is 475-500.

Two tests are commonly used for hardness testing.


Warranty

Basics11

Guaranteed against breakage! Warranty appliesto a John Deere ADI, cast or forgedreplacement tooth that breaks during operationbefore it wears out provided: (1) the tooth hasnot been hard faced or repaired, (2) it is usedon a matching tooth adapter, and (3) the toothsupport surface of the adapter has beenproperly maintained. A new tooth of the sametype will be furnished free of charge by anyauthorized John Deere industrial dealer.

John Deere’s obligation under this warrantydoes not cover hardware for attaching the tooth

or labor for tooth removal and installation; allother remedies are expressly excluded.

In addition, John Deere’s normal partswarranty and its terms and conditions (see JohnDeere Service Parts Warranty for details)applies to any ADI, cast or forged tooth underthe above warranty which may otherwise provedefective in material or workmanship within 90days after purchase.


Tooth Pocket Dimensions(Refer to Replacement Section for Specific Part Numbers)

Tooth Pocket Dimensions1

Tooth Pocket Width Tooth Pocket Height Replacement Section Series

1-13/32″ 1-27/32″ Caterpillar 20

1-1/2″ 1-5/8″ H & L 23

1-9/16″ 1-11/16″ H & L –

1-9/16″ 2-1/8″ H & L 24

1-5/8″ 1-5/8″ Hensley 156

1-5/8″ 2-3/8″ Hensley 160

1-3/4″ 2-11/32″ Caterpillar 22

1-13/16″ 1-1/2″ Esco Conical 18

1-15/16″ 2-11/16″ Caterpillar 25

2-1/16″ 2-1/8″ H & L 25

2-1/4″ 2-1/8″ Hensley 220

2-3/8″ 3-1/32″ Caterpillar 30

2-1/2″ 2-1/8″ Esco Conical 25

2-11/16″ 3-5/16″ Caterpillar 35

2-7/8″ 2-1/8″ H & L 27

2-7/8″ 2-11/16″ Hensley 290

3″ 2-1/8″ Hensley 310

3″ 2-1/4″ Esco Conical 30

3-5/32″ 3-21/32″ Caterpillar 40

3-13/32″ 3-3/16″ Hensley 330

3-1/2″ 2-5/8″ Esco Conical 35

3-1/2″ 2-7/8″ Hensley 350

3-17/32″ 3-29/32″ Caterpillar 45

4″ 2-7/8″ Hensley 400

4″ 3″ Esco Conical 40

4-5/16″ 4-11/32″ Caterpillar 55

4-1/2″ 3-1/4″ Esco Conical 45

4-3/4″ 3-1/2″ Hensley 475

4-7/8″ 5-1/2″ Caterpillar 45 Abrasion (Standard)

6″ 5−29/32″ Caterpillar 70


At times, part number information is not always readable on a worn tooth.There are several ways to identify a design and then a specific part number:

1. Tooth Pocket DimensionsMeasure the tooth pocket width and height and reference the dimensionsin the list below to isolate the tooth type (Caterpillar, H & L, Hensley, etc.)and series. Then look in the corresponding replacement section whichincludes photos, line drawings, and dimensions to establish the toothneeded for the application.

2. Retention HardwareUse the actual size illustrations of the retention hardware included at theend of each replacement section to determine possible tooth type(Caterpillar, H & L, Hensley, etc.) and size.

Fanggs Teeth: A John Deere Exclusive!

Fanggs/John Deere1

Better Bucket Fill

Better Level Bucket Operation

Better Start-Dig Characteristics

Exclusive to John Deere

Curved Profile

Fanggs teeth are curved. That is why they dig with less effort. The curved profile allows themto closely track the path of the bucket. Conventional teeth work against the bucket as they passthrough the soil.

Whether it is breaking-up gumbo, slicingthrough frost, moving hard-packed sand, orgeneral-purpose digging, Fanggs will answerthe call! The patented, guaranteed-against-breakage, competitively-priced Fanggs teethprovide better bucket fill, better level bucketoperation, and better start-dig characteristicsdue to their design.

Without Fanggs Teeth With Fanggs Teeth

Better Bucket-Fill and Faster Cycles with Fanggs Teeth

You get better bucket-fill and faster cycles with Fanggs teeth because the rolling action causes the soil to collect at theback of the bucket instead of the middle.



Fanggs/John Deere2

Self-Cleaning EffectFanggs teeth have a self-cleaning effect that letsdirt flow between the teeth. The moldboard-shaped sidewalls decrease friction and soilcompaction.

Wear CharacteristicsWear characteristics are relative to yourapplication and the material you are working in.But there are many instances where the weardifferential of Fanggs teeth is more - lots more -than conventional teeth.

Soil Bin TestA soil bin test was performed using a Fanggstooth and a standard tooth.

Teeth were assembled to run one at a timecompletely submerged through identicallycompacted soil. Tests were run at a constant 1/2 mph.

The standard tooth required 101.5 pounds offorce while the Fanggs tooth required only 78.5pounds of force to transverse the same soil. TheFanggs tooth required nearly 22.7% less effortto do the same work!

Soil Bin Test ResultsForce Required

Standard Tooth 101.5 poundsFanggs Tooth 78.5 poundsAdditional Force Required

with Standard Tooth 23.0 pounds

23.0 pounds divided by 101.5 pounds =nearly 22.7% less effort required with the Fanggs tooth!

Vertical ForceThere was also a significant difference noted in the vertical force between the standard toothand Fanggs. The standard tooth showed a 4.7 pound force trying to plane up out of the soil.The Fanggs tooth had a 5.0 pound force trying to go deeper. So while requiring nearly 23% lesseffort to traverse the same soil, the Fanggs tooth was trying to work harder.



Fanggs/John Deere3

Each tooth is designed to provide optimum performance by filling the bucket faster and requiringless force. Material flow during operation is smooth and consistent on both the top and sidesurfaces.

Operation ComparisonsLet’s take a look at comparisons of Fanggs and conventional teeth during various operations.

Two Types of FanggsThere are two basic designs of the Fanggs teeth: one is for digging, the other for loading.

Digging Tooth Loading Tooth

Conventional Tooth Fanggs Tooth Conventional Tooth Fanggs Tooth

Digging

A conventional tooth uses a wedgingaction to penetrate material.

A Fanggs tooth slices through materialfor more productivity and less effort.

Loading

A ski-nose pattern appears onconventional loader teeth.

The Fanggs design creates a level bucketwear pattern.

Crowding

Conventional teeth rake material away from walls.

Fanggs teeth peel material away from walls.



Fanggs/John Deere4

Operator Tips

With conventional teeth, many operators start by raking the earth. It is a fast way to open the land,but it can wear out a set of teeth very quickly.

The unique slicing action of Fanggs teeth make raking unnecessary. You can start diggingimmediately. Here’s how:

Part No. ExplanationVarious information can be determined from the part number system. Refer to the following chartfor basic part numbering information.

1. Start with a steep angle of entry as shown above.

2. Keep the bucket at a flatter attitude as you continue to dig.

3. Maintain this flat profile, then curl the bucket as you complete the dig cycle.

This technique allows you to do the job faster and requires less power. It also helps maintain thenatural compaction of the soil while reducing the chance of undercutting.

123

Part Number Explanation for John Deere Fanggs

Prefix Suffix Explanation

TF D Fanggs Digging

TF L Fanggs Loading


Fanggs/John Deere

Fanggs/John Deere5

Horizontal Pin and Split WasherReplacement teeth for both John Deere andCaterpillar are retained with a horizontal pinand split washer. This 2-piece retention methodmakes tooth removal and installation fast andeasy. Both the pin and washer are reusable.

Special ToolsWhen removing spring pins from John Deereteeth, use special tool JDG97.

When removing flex pins from backhoe andexcavator teeth, use special tool D05339ST.These tools are available from SERVICE-GARD.

Pin Master® is also available and boasts of 3minute removal and replacement time for anentire set of 23 Series backhoe teeth. OrderTY15994 through your normal parts system.

The flex pin is designed to withstand shockand take up small amounts of adapter wear toprovide the necessary tight fit. The pin shouldbe installed so the half groove faces forwardtowards the tooth tip. The groove is thelocking mechanism.

Flex pins are reusable when properlyremoved. Use special tool D05339ST whenremoving flex pins from backhoe andexcavator teeth – see “Special Tools.”

Do not use bolts in place of flex pins wheninstalling teeth. Bolts create wear on pin holesand promote tooth breakage. If teeth do notstay on, there is probably an adapter problem.

Spring PinThe spring pin is an economical means ofretaining teeth. The spring in the pin takes upmanufacturing tolerances and keeps the toothtight against the adapter.

When removing spring pins from John Deereteeth, use special tool JDG97 (see Special Toolsbelow).

Retention and Installation

Flex Pin

Pin Master® Tooth Replacement Tool(TY15994)


John Deere Fanggs Digging and Loading Teeth

Fanggs/John Deere12

TF__D (Digging) • For general-purpose to heavy-duty digging conditions.TF__L (Loading) • Fanggs digging teeth have a curved shape and track the path of the bucket.Non-Centerline • Fanggs loading teeth have a flat bottom for improved bucket control.

-A- -B- -C- -D- -E-Pocket Pocket

Series Tooth Part No. Length Width Point Width Height

Cat 20 Series TF1U3202 (Digging) 5-7/8″ 1-3/4″ 1/8″ 1-13/16″ 1-5/8″ADI 4.1 lb.

Retainer TF1U3202P Cat: 416, 426, 428, 436; Competitive: Equipment withWasher T4T0001 Cat 20 Series-type adapters.

Cat 25 Series TF1U3252D (Digging) 7-5/8″ 2-1/2″ 1/8″ 2-11/16″ 2″Cast 9.0 lb.

Retainer T9J2258 Retainer PM8E6258 Cat: 205, 206, 211, 212, 213B, 214B, 613, E110, Washer T3G9609 Washer PM8E6259 E120B, E200, EL200; Competitive: Equipment with Cat

25 Series-type adapters.

Cat 25 Series TF1U3252L (Loading) 7-5/8″ 2-1/2″ 1/8″ 2-11/16″ 2″Cast 9.0 lb.

Retainer T9J2258 Retainer PM8E6258 JD: 544E, 544G, 624E, 624G, 644H; Cat: 613, 916,Washer T3G9609 Washer PM8E6259 920, 924F, 926, 930, 936, 938F, 939, 941, 941B, 943,

943GLP, 951, 951C, 953, 953GLP, IT12, IT24, IT28;Competitive: Equipment with Cat 25 Series-typeadapters.

Cat 30 Series TF1U3302D (Digging) 9″ 3″ 1/8″ 3″ 2-1/2″ADI 12.3 lb.

Retainer T9J2308 JD: 690E; Cat: 205, 206, 211, 212, 213B, 214B,Washer T3G9609 215, 219, 224, 235, E180, E200, EL200; Competitive:

Equipment with Cat 30 Series-type adapters.

Cat 30 Series TF1U3302L (Loading) 8-3/4″ 3″ 1/4″ 3″ 2-1/2″Cast 13.3 lb.

Retainer T9J2308 JD: 644E, 644G, 644H; Cat: 950, 950B, 955, 966,Washer T3G9609 966C; Competitive: Equipment with Cat 30 Series-type

adapters.


John Deere Fanggs Digging and Loading Teeth (Continued)

Fanggs/John Deere13



Cat 35 Series TF1U3352D (Digging) 10″ 3-3/8″ 4-3/4″ 3-1/4″ 2-15/16″Cast 16.9 lb.

Retainer T9J2358 Retainer T8E6358 JD: 790D, 790E, 892D, 892E; Cat: 205, 206, 211,Washer T3G9549 Washer T8E6359 212, 213B, 214B, 224, 225, 229, 231, 245, E240, E248;

Competitive: Equipment with Cat 35 Series-typeadapters.

Cat 45 Series TF9W8452D (Digging) 10″ 3-3/8″ 4-3/4″ 3-7/8″ 3-7/8″Cast 28.5 lb.

Retainer T1U1458 Retainer PM8E0468 JD: 790D, 790E, 892D, 892E, 992, 992D; Cat: 224, Washer T3G9549 Washer PM8E8469 225, 229, 235, 325, 330, 375, E240, E248, E300;

Competitive: Equipment with Cat 45 Series-typeadapters.

H & L 23 Series TF23D (Digging) 6″ 1-3/4″ 1/8″ 1-1/2″ 1-5/8″ADI 3.8 lb.

Pin TF23P JD: Buckets with H & L 23 Series adapters (5/8″ or3/4″ edge); Case: 480F, 580K, 590, 680L, 780D; Ford: 555D, 575D, 655D, 755B, 710D; Competitive:Backhoes with H & L 23 Series-type adapters (5/8″ or3/4″ edge).

H & L 23 Series TF23L (Loading) 5-7/8″ 1-3/4″ 1/4″ 1-1/2″ 1-5/8″ADI 3.3 lb.

Pin TF23P JD: Backhoe loading buckets with H & L 23 Series-type adapters; Skid-Steer: JD14, JD24, JD24-A; Case:480F, 580K, 580L, 590, 590L, 680L, 780D; Ford:555D, 575D, 655D, 755B.

H & L 25 Series TF252 (Digging) 7-1/2″ 2-1/2″ 1/8″ 2-1/16″ 2-1/8″ADI 8.8 lb.

Pin TF25P JD: 690, 690A, 690B, 690C, 690D, 690E;Competitive: Excavators with H & L 25 Series-typeadapters (1-1/2″ edges).


Digging Loading


Fanggs/John Deere14



Hensley 156 Series TF156 (Digging) 6″ 1-3/4″ 1/8″ 1-5/8″ 1-5/8″ADI 3.9 lb.

Pin TF13P JD: 300D, 310D, 315D, 410D, 500B, 510, 510D, 710B;Competitive: Backhoes with Hensley 156 Series-typeadapters (1″ edges).

Hensley 160 Series TF160 (Digging) 6-1/4″ 2-1/8″ 1/8″ 1-5/8″ 2-3/8″Cast 4.2 lb.

Pin TP160 JD: 190E, 290D; Competitive: Backhoes andexcavators with Hensley 160 Series-type adapters (1″ edges).

Hensley 220 Series TF220 (Digging) 7″ 2-5/8″ 1/4″ 2-1/4″ 2-1/8″Cast 6.0 lb.

Pin TP160 JD: 490, 490D, 490E, 495D, 590D, 595, 595D;Competitive: Backhoes and excavators with Hensley220 Series-type adapters (1-1/4″ edges).


Pin TK290 JD: 490, 490D, 490E, 495D, 590D, 595, 595D, 690,690A, 690B, 690C, 690D, 690E; Competitive:Excavators with Hensley 290 Series-type adapters(1-1/2″ edges).

Hensley 310 Series TF310 (Digging) 7-1/2″ 3-1/4″ 1/4″ 3″ 2-1/8″Cast 10.4 lb.

Pin TP160L JD: 590D, 595, 595D, 690, 690A, 690B, 690C, 690D,690E, 790, 790D, 790E, 792, 792D; Competitive:Excavators with Hensley 310 Series-type adapters (1-1/2″ edges).


Pin TK330 JD: 590D, 595, 595D, 690, 690A, 690B, 690C, 690D,690E, 790, 790D, 790E, 792, 792D; Competitive:Excavators with Hensley 330 Series-type adapters (1-1/2″ edges).


Pin TP400HD Competitive: Excavators with Hensley 350 Series-typeadapters.



Fanggs/John Deere15



Hensley 400 Series TF400 (Digging) 9-1/4″ 4-1/2″ 1/4″ 4″ 2-7/8″Cast 19.7 lb.

Pin TP400HD JD: 690, 690A, 690B, 690C, 690D, 690E, 790, 790D,790E, 792, 792D, 890, 890A, 892D, 892E, 992D, 992E;Competitive: Excavators with Hensley 400 Series-typeadapters (2″ edges).


Pin TP475 JD: 890, 890A, 892D, 892E, 992D, 992E;Competitive: Excavators with Hensley 475 Series-typeadapters (2-1/2″ edges).

John Deere TF13 (Loading) 6-3/8″ 2-5/8″ 1/8″ 1-1/2″ 1-1/8″ADI 3.9 lb.

Pin TF13P Ref. 2 Crawler Loaders: 1010, 2010, 350, 350A, 350B,350C, 355D; Wheel Loaders: 310, 400, 401A, 401C,410, 410B, 415B, 500, 500A, 500C, 510B, 515B, 610B,710B, 710C, 710E

John Deere TF10L (Loading) 5-1/2″ 3-5/8″ 1/8″ADI 6.1 lb.

Pin TF10P Ref. 1 4-Wheel Drive Loaders: 544E, 544G, 544H, 624E,Washer T112196 624G, 644E, 644G; Crawler Loaders: 455G, 555G

John Deere TF11L (Loading) 6″ 3-5/8″ 1/8″ 2−3/8″ 1−3/4″ADI 5.1 lb.

Pin TP160L Ref. 1 4-Wheel Drive Loaders: 444, 444C, 444CH, 444D,544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C,644D; Compactors: 646, 646B, 646C; CrawlerLoaders: 450, 450B, 450C, 455D, 455E, 555, 555A,555B, 655, 755, 755A

John Deere TF33L (Loading) 9-5/8″ 3-1/4″ 1/8″ 2−1/2″ 3−1/8″Cast 15.0 lb.

Pin T67083 Ref. 1 4-Wheel Drive Loaders: 744E, 744H, 844; Washer T67086 Crawler Loaders: 655, 655B, 755, 755A, 755B


Reference 1 Reference 2

John Deere Chisel Teeth

Fanggs/John Deere16



T105690 5-7/8″ 2″ 3/8″ 2-1/4″ 1-3/4″Cast 4.7 lb.

Pin T112195 4-Wheel Drive Loaders: 544E, 544G, 544H, 624E, Washer T112196 624G, 644E, 644G; Crawler Loaders: 455G, 555G

T69647 9-1/8″ 2-5/8″ 1/4″ 2-1/2″ 3″Cast 10.5 lb.

Pin T67083 4-Wheel Drive Loaders: 744E, 744H, 844;Washer T67086 Crawler Loaders: 655, 655B, 755, 755A, 755B, 855


John Deere Standard Teeth

Fanggs/John Deere17


Series Tooth Part No. Ref. Length Width Point Width Height

John Deere T103189 5-9/16″ 3-11/16″ 3/16″ 2-1/4″ 1-3/4″Cast 5.9 lb.

Pin T112195 1 4-Wheel Drive Loaders: 544E, 544G, 544H, 624E,Washer T112196 624G, 644E, 644G; Crawler Loaders: 455G, 555G

John Deere T29887 5-3/4″ 2-13/16″ 1/4″ 2-3/8″ 1-3/4″Cast 5.0 lb.

Pin TP160 1 4-Wheel Drive Loaders: 444, 444C, 444CH, 444D,544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C,644D; Compactors: 646, 646B, 646C; CrawlerLoaders: 655, 755, 755A

John Deere T56004 8″ 4-5/8″ 7/16″ 3-3/16″ 2-1/4″Cast 13.1 lb.

Pin T56005 1 4-Wheel Drive Loaders: 844

John Deere T79008 9-1/8″ 4-1/8″ 3/16″ 2-1/2″ 3″Cast 14.0 lb.

Pin T67083 1 4-Wheel Drive Loaders: 744E, 744H, 844Washer T67086

John Deere TH106698 5-1/2″ 2-1/4″ 3/16″ 1-7/8″ 1-7/8″Cast 3.1 lb.

Wedge Pin TH106699 2 Excavators: 70, 70DLock TH106700

John Deere U13449 4-5/16″ 2-5/8″ 3/16″ 1-1/2″ 1-1/8″Cast 2.2 lb.

Pin 34M7070 1 Crawler Loaders: 1010, 2010, 350, 350A, 350B,350C, 355D; Wheel Loaders: 310, 400, 401A, 401C,410, 410B, 415B, 500, 500A, 500C, 510B, 515B, 610B,710B, 710C, 710E

John Deere U16086 5-3/8″ 3-5/8″ 5/16″ 2-3/8″ 1-3/4″Cast 4.5 lb.

Pin TP160 1 4-Wheel Drive Loaders: 444, 444C, 444CH, 444D,544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C,644D; Crawler Loaders; 450, 450B, 450C, 455D,455E, 555, 555A, 555B; Scraper Bowls: 760, 760A,762, 762A, 762B, 860, 860A, 860B, 862, 862B



John Deere Standard Bolt-On Teeth

Fanggs/John Deere18

-A- -B- -C-Length Width Point -D- -E-

HoleSeries Tooth Part No. Ref. -F- -G- Spacing Wt.

John Deere AT121474 12-3/4″ 2″ 3/16″ 2-5/8″ 15/16″Center 3 7-1/4″ 23˚ 4″ 9.9 lb.

JD: 344E, 344H, 444E

John Deere AT121475 12-3/4″ 2-3/8″ 1/4″ 2-5/8″ 15/16″Corner, Right-Hand 4 7-1/4″ 23˚ 4″ 13.7 lb.

JD: 344E, 344H, 444E

John Deere AT121476 12-3/4″ 2-3/8″ 1/4″ 2-5/8″ 15/16″Corner, Left-Hand 4 7-1/4″ 23˚ 3-7/8″ 14.0 lb.

JD: 344E, 344H, 444E

John Deere T110052 9-1/2″ 1-5/8″ 1/4″ 4-7/8″ 11/16″2 2-3/8″ 1-3/4″ 5.7 lb.

JD: 50

John Deere T110058 8-1/4″ 1-3/8″ 1/4″ 3-3/4″ 5/8″2 2″ 1-3/4″ 3.9 lb.

JD: 30

John Deere T111297 8″ 1-1/4″ 1/4″ 4″ 9/16″2 3.5 lb.

JD: 15

John Deere T115680 9-3/4″ 2-1/2″ 1/4″ 5-1/4″ 5/8″1 2-1/2″ 60˚ 3-1/2″ 6.1 lb.

JD: 84


Reference 1 Reference 2 Reference 3 Reference 4

John Deere Adapters

Fanggs/John Deere19PI7262 Litho in U.S.A. (97-02)


Reference 4Reference 3


Reference 7

John Deere Adapters

Fanggs/John Deere20

Adapter Type Hole Wt.Part No. Attachment Ref. A B C D Spacing (lb.)

T103190 Bolt-On 1 7-3/4″ 1-1/4″ 4-3/4″ 30˚ 4-13/16″ 14.4Center

T103191 Bolt-On 2 8-1/4″ 1-1/4″ 1-3/4″ 30˚ 23.2Corner

T104673 Bolt-On 3 7-7/16″ 1-5/16″ 8-15/16″ 30˚ 4-11/16″ 27.0Center

T104674 Bolt-On 2 8-15/6″ 1-1/4″ 2-3/4″ 30˚ 4-13/16″ 33.6End

T105692 Bolt-On 1 5-5/8″ 1″ 3-5/8″ 30˚ 3-5/8″ 10.6Center

T112163 Bolt-On 2 5-5/8″ 1″ 1-5/8″ 30˚ 14.2Corner

T112164 Bolt-On 1 5-7/8″ 3/4″ 4″ 30˚ 3-5/8″ 9.5Center

T123077 Bolt-On 3 9-1/4″ 1-1/2″ 10-1/2″ 30˚ 5-3/16″ 40.4Center

T29886 Bolt-On 1 8-1/4″ 1-3/8″ 4″ 30˚ 6″ 12.6

T35385 Bolt-On 1 8-5/8″ 1-1/2″ 5-7/16″ 32˚ 5-1/4″ 14.7

T38783 Bolt-On 5 8-3/8″ 1-1/8″ 9-7/8″ 30˚ 2″ 12.3

T56003 Bolt-On 3 8-1/4″ 1-15/16″ 10-1/2″ 30˚ 5″ 36.7

T79004 Bolt-On 3 8-9/16″ 1-13/16″ 11-1/4″ 30˚ 5-3/16″ 38.2Center

T79006 Bolt-On 2 11-13/16″ 1-1/2″ 2-3/8″ 30˚ 57.2Corner

TH106697 Weld-On 7 1-7/8″ 15/16″ 5-1/4″ 30˚ 6.6

Note: John Deere adapter and teeth applications are listed on pages 10-11.


John Deere Adapters (Continued)

Fanggs/John Deere21

Adapter Type Hole Wt.Part No. Attachment Ref. A B C D Spacing (lb.)

U16087 Bolt-On 6 7-1/2″ 1-1/2″ 8-1/8″ 35˚ 2″ 9.3

U16864 Bolt-On 1 8-5/8″ 1-1/8″ 3-7/8″ 32˚ 6-1/2″ 10.3

U41344 Bolt-On 1 4-7/16″ 1-1/8″ 3-3/8″ 30˚ 2-3/8″ 5.2

Adapter Hardware

Adapter Bolt Size Bolt Nut Washer

T103190 1″ x 3-1/8″ 19M7287 14M7278 24M7243

T103191 1″ x 3-1/2″ 19M8288 14M7278 24M7243

T104673 1″ x 4-1/4″ 19H3556 K40018 T75690

T104674 1-1/4″ x 4-1/4″ 19H3594 A20329 T81065

T105692 3/4″ x 2-1/2″ 19M8102 14M7277 24M7242

T112163 1″ x 3-1/2″ 19M8288 14M7278 24M7243

T112164 3/4″ x 2-1/2″ 19M8102 14M7277 24M7242

T123077 1-1/4″ x 5″ 08H4815 A20329 T79096

T29886 5/8″ x 3-1/4″ 19H2072 K40015 24H1367

T35385 3/4″ x 2-1/4″ 19H1782 K40016 24H1400

T38783 3/4″ x 4″ T70287 14H1046 T83426

T56003 7/8″ – _ _

T79004 1-1/4″ – – –

T79006 1-1/4″ x 4-1/2″ 08H4814 A20329 T79096

U16087 3/4″ x 4″ T70287 14H1046 12H236

U16864 5/8″ x 3-1/4″ 10H1157 K40015 24H1367


John Deere Hardware

Fanggs/John Deere22

Illustrated parts are actual size.

TF10P

T112196

T112195

TT9J2308

TH106699

T3G9609

TH106700


John Deere Hardware

Fanggs/John Deere23


34M7070

TF13P

TP160

TP160L

T56005


John Deere Replacement Teeth for Caterpillar ProductsOversized Pocket and Extended AdapterNose Piece

The John Deere replacement teeth forCaterpillar products come in sizes andtypes to fit almost all machine makes andmodels. The oversized pocketcharacteristics of these teeth with theextended adapter nose piece provide a nosefit between the tooth and adapter whichresults in strong impact resistance but aloose fit in the ramps.

Pin and Washer Retention

Replacement teeth for Caterpillarequipment use a 2-piece retention methodwhich makes tooth removal and installationfast and easy. Both the pin and the washerare reusable. The original style and "E"style are now available.

Original Style Pins and Washers

The original retention for replacementCaterpillar teeth use a horizontal pin andsplit washer.

Do not use the new "E" washers with theoriginal style pins.

"E" Pins and Washers

Centerline Design, Oversized Pocket .Nose fit provides impact resistance with loose pinand ramp fit.

"E" Pins and Washers have an "E" in the Part No.

The shallow radius groove on the "E" pinreduces the spread which increases lockingforce.

The tapered pin outer edge reduces contactwith the inside of the adapter counterbore.This minimizes breakage.

The new pin jacket on the washer aligns thepin and washer during installation.

Do not use split washers with "E" washerswith "E" pins. "E" pins and washers areinterchangeable with original pins/washersin all sizes except J450/J460 adapters.Original pins/washers fit J450 adapters."E" pins/washers fit J460 adapters

John Deere Replacement Teeth for Caterpillar ProductsVarious information can be determined from the part numbering system. Refer to thefollowing chart for basic part number information.Part Number Explanation (Replacement Teeth for Caterpillar Products)P r e f i x and S u f f I x ExplanationPM or T 0 FlarePM or T 1 ShortPM or T 2 LongPM or T 2 Heavy Duty LongPM or T 3 AbrasionPM or T 9 PenetrationPM or TT T TigerPM or TX WT Twin TigerTF D Fanggs DiggingTF L Fanggs LoadingPM SYL Ribbed SharpPM RC Rock ChiselPM RP Rock Penetrator Examples:

NOTES:

The "Series" equipment thetooth is used on is generallyprovided in the part number.

"N" within the part numberdesignates heavy-duty.

See examples below.

T3G8250 Flare Tooth used with 25 Series Adapters (T3G8250)T9N4252 Long (Heavy-Duty) used with 25 Series Adapters (T9N4252)T9N4353 Abrasion Tooth used with 35 Series Adapters (T9N4353)T1U3551 Short Tooth used with 55 Series Adapters (T1U3551)TF1U3252D Fanggs Digging used with 25 Series Adapters (TF1U3252D)

John Deere Replacement Teeth for Caterpillar Products - Types Available

Fanggs Digging Teeth(Non-Centerline)

TF_D Part Numbers• For general-purpose to

heavy-duty diggingconditions.

• Provide a clean start andclose crowd.

Fanggs Loading Teeth(Non-Centerline)

TF_L part Numbers• For general-purpose to

heavy-duty diggingconditions.

• Flat bottom for improvedbucket control.

Short Teeth(Centerline)

PM or T_1 Part Numbers• Designed for use in high-

impact and pry-out work.• Provides more strength but

less wear than the long toothLong Teeth (Centerline)

PM or T_2 Part Numbers• For loading and digging


Tiger Teeth(Non-Centerline)

PM or TT_T Part Numbers• Long, aggressive teeth

designed for breakingextremely tight soil.

• Used primarily as centerteeth

Twin Tiger Teeth(Non-Centerline)

PM or TX_WT Part Numbers• For densely compacted

material.• Use primarily as a corner

tooth but can be used incenter.

Flare Teeth(Centerline)

PM or T_0 Part Numbers• Work extremely well in

loose and mud-likeconditions.

Penetrator Teeth(Non-Centerline)

PM or T_9 Part Numbers• Use in highly compacted,

dense material such as clay.• Center rib provides added

strength.• Maintains good sharpness

throughout its life.

Abrasion Teeth (Standard andHeavy-Duty)

(Non-Centerline)PM or T_3 Part Numbers

• Use where extended tip lifeis needed in highly-abrasiveconditions.

• Heavy-duty teeth have morewear material than thestandard teeth.

Ribbed Sharp(Centerline)

PM _SYL Part Numbers• Excellent Penetration• Greater Wearlife than tiger• For digging in tight or

compacted material


Rock Chisel(Non-Centerline)

PM _RC Part Numbers• Extremely abrasive terrain

requiring extra penetration.• Increased Wear Material

Rock Penetrator(Non-Centerline)

PM _RP Part Numbers• Loaders in high abrasion

quarry and miningoperations.

.

H.D. Long(Non-Centerline)

PM or T_2 Part Numbers• Use in high abrasion

application• Added wear material in tip

for longer wear life.

Replacement for Caterpillar Products RetainersIllustrated parts are actual size

TF1U3202P

T8E6208

T8E6209

20 Series Fanggs

T4T0001

20 Series except Fanggs

Replacement for Caterpillar Products Retainers (Continued)Illustrated parts are actual size

T6Y322822 Series

2

T8E625825 Series

T9J225825 Series

s

T9J230830 Series

T8E62592, 25 Series

T3G960925, 30 Serie


T7T340840 Series

T7T340940 Series

T8E635935 Series

T8E635835 Series

T9J235835 Series

T3G954935 Series


T3G954935, 45 Series

T8E846945 Series

(J

T8E046845 Series

(J460 Adapters)

T1U145845 Series

450 Adapters)

Replacement for Caterpillar Products Retainers (Continued)

Illustrated parts are actual size

T3G955955 Series

T1U155855 Series

Caterpillar - Tooth by Series

g Fanggs dig TF1U3202 üm long T1U3202 üd tiger TT1U3202 üj twin tiger TX1U320WT üa abrasion T4T2203 üf penetrator T1U3209 ü- org pin TF1U3202P ü- org wash T4T0001 ü- e type pin T8E6208 ü- e type wash T8E6209* ü- adapter PM4T1204 ü Cat flush weld-on: 416, 910, 931 - adapter T8J7525 ü Cat center weld-on bottom strap: 416, 426, 428, 436, 438, 910, 914G,

931, 935

22 Seriesstyle description part no. disc. used on

m long T6Y3222 ü- e type pin T6Y3228 ü- e type wash T8E6259 ü- adapter PM6Y3224 ü Cat weld-on double strap: 446, 933, 307, 307B

20 Series

a

a

Caterpillar - Applications25 Seriesstyle description part no. disc. used on

g Fanggs dig TF1U3252D ü

c Fanggs load TF1U3252L üh short T1U3251 üm long T1U3252 üd long h-d T9N4252 ük tiger TT1U3252 üj twin tiger TX1U3252WT ül flare T3G8250 üf penetrator T9J4259 üe abrasion h-d PM9N4253 üa abrasion T4T2253 üb ribbed sharp PM1U3252SYL ü- org pin T9J2258 ü- org wash T3G9609 ü- e type pin T8E6258 ü- e type wash T8E6259 ü- adapter T25CA ü J D center bolt-on: 544E, 544G, 544H, 624E, 624G, 624H

- adapter T25EA ü J D center bolt-on: 544E, 544G, 544H, 624E, 624G, 624H- adapter T1U1254 ü Cat flush weld-on: 205, 206, 211, 212, 213B, 214B, 918F, 920, 926, 928,

936, 953, 951, 953B, 953C

- adapter T3G0169 ü Cat center weld-on: 205, 206, 211, 212, 213B, 214B, 916, 920, 926, 930, 936, 941, 941B, 951, 951C, 953, 953B, 953C

- adapter T1U0257 ü Cat center bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939, 941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C

- adapter PM3G4258 ü Cat left bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939, 941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C

- adapter PM3G4259 ü Cat right bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939, 941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C

- adapter PM6Y3254 ü Cat center weld-on: 311, 312, 311B, 312B, 312BL

Caterpillar - Applications


g Fanggs dig TF1U3302D üc Fanggs load TF1U3302L üh short T1U3301 üm long T1U3302 üd long h-d T9N4302 ük tiger TT1U3302 üj twin tiger TX1U3302WT ül flare T107-3300 üf penetrator T9J4309 üe abrasion h-d T9N4303 üa abrasion T4T2303 üb ribbed sharp PM1U3302SYL ün rock chisel PM1U3302RC

- org pin T9J2308 ü- org wash T3G9609 ü- adapter T30CA ü JD center bolt-on: 644E, 644G, 644H,

- adapter T30EA ü JD end bolt-on: 644E, 644G, 644H,

- adapter T3G6304 ü JD double strap center: 690E, Cat double strap center: 215, 219, 315, 315B, 315BL, 320, 320B

- adapter T1U0307 ü Cat center bolt-on: 944, 950, 953B, 955

- adapter PM3G4308 ü Cat 1 - 1-1/4" edge left bolt-on: 950B, 955, 960F, 963 - adapter PM3G4309 ü Cat 1 - 1-1/4" edge right bolt-on: 950B, 950E, 950F, 950G 955, 960F,

962G, 963

- adapter T4T4307 ü Cat center bolt-on: 950, 953B, 955, 960F, 963

- adapter PM3G9307 ü Cat center bolt-on: 966, 966C,

- adapter PM3G8308 ü Cat 1-1/4" edge left bolt-on : 962G, 966, 966C

- adapter PM3G8309 ü Cat 1-1/4" edge right bolt-on : 962G, 966, 966C- adapter PM1U1304 ü Cat flush weld-on: 944, 950, 955, 966



g Fanggs dig TF1U3352D üh short T1U3351 üm long T1U3352 üd long h-d T9N4352 ük tiger TT1U3352 üj twin tiger TX1U3352WT ül flare T107-3350 üf penetrator T9J4359 üe abrasion h-d T9N4353 üa abrasion T4T2353 üb ribbed sharp PM1U3352SYL ün rock chisel PM1U3352RC

I rk penetrator PM4T2353RP

- org pin T9J2358 ü- org wash T3G9549 ü- e type pin T8E6358 ü- e type wash T8E6359 ü- adapter T3G8354 ü JD double strap center: 790D, 892D, 892E, Cat double strap center: 215,

219, 225, 229, M318, 320, 320B, 320BL, 322, 322B, 322BL, 325BL, 325B, 325

- adapter PM1U1354 ü Cat flush weld-on: 245, 950, 950B, 963B, 966C, 966D, 966E, 966F, 973, 973LPG, 977, 977L, 980, 980B

- adapter PM8J5357 ü Cat center bolt-on: 963, 966- adapter T3G3357 ü Cat center bolt-on: 960F, 966, 966D, 966E, 966F, 970, 970F, 973,

973LPG, 977, 977L

- adapter PM3G5358 ü Cat cornergaurd LH: 960F, 966, 966D, 966E, 966F, 970, 970F, 973, 973LPG, 977, 977L,

- adapter PM3G5359 ü Cat cornergaurd RH:960F, 966, 966D, 966E, 966F, 970, 970F, 973, 973LPG, 977, 977L,

- adapter PM8J3357 ü- adapter PM1U1357 ü Cat Center Bolt-on: 980C, 980F

- adapter PM1U1350 ü Cat Center Bolt-on: Spade Nose 980C- adapter PM9J2357 ü



m long T7T3402 üd long h-d T8E4402 üf penetrator T6Y7409 üf penetrator PM6Y7409 ün rock chisel PM7T3402RC

- org pin T7T3408 ü- org wash T7T3409 ü- e type wash T8E8409 ü- adapter PM7T3404 ü

Cat double strap center: 320L, 325L, 330L, 322L, 330BL, 345B, 345BL, 320BL, 322BL, 325BL, 320B, 322B, 325B, 330B, 320, 322, 325, 330



g Fanggs dig TF9W8452D üh short T9W8451 üm long T9W8452 üd long h-d T9N4452 ük tiger PM1U3452Tj twin tiger PM1U3452WTl flare T107-3450 üf penetrator T9W8459 üa abrasion PM9W1453 üe abrasion h-d T9N4453 üb ribbed sharp PM9W8452SYL ün rock chisel PM1U3452RCI rk penetrator PM9W1453RP- org pin T1U1458 ü- org wash T3G9549 ü- e type pin T8E0468* ü- e type wash T8E8469* ü- adapter T1U1454 ü JD double strap center: 790D, 790E, 892D, 892E, 992, 992D

- adapter T8E6464** ü Cat double strap center: 229, 235, 330, 330B, 330BL, 345, 345BL, 350, 350L

- adapter PM8E3464** ü Cat spade nose double strap center weld-on: 973SLAG, 983, 988, 988B

- adapter PM8E3465** ü Cat spade nose double strap RH: 983, 988, 988B

- adapter PM8E3466** ü Cat spade nose double strap LH: 983, 988, 988B

- adapter PM8J1454 ü- adapter PM9J9584 ü Cat flush mount weld-on:

Note: All 45 Series adapter will not accept e-type pins and retainers * used on J460 adapters only** J460 adapter



h short T1U3551 üm long T1U3552 üd long h-d PM9N4552 üf penetrator T9J4559 üe abrasion h-d PM6Y2553 ün rock chisel PM1U3552RCI rk penetrator PM9W1553RP- org pin T1U1558 ü- org wash T3G9559 ü- e type pin T6Y8558 ü- e type retainer T8E5559 ü- adapter PM1U1553 ü Cat double strap: 245, 345, 345B, 345BL, 350, 350L, 375

- adapter PM3G9494 ü Cat double strap center: 245FS

- adapter PM3G9495 ü Cat double strap RH: 245S- adapter PM3G9496 ü Cat double strap LH: 245S


m long T4T4702 üa abrasion PM4T4703 ü- washer T4T4707 ü- pin T9U9616 ü- adapter T4T4704 ü

Cat double strap: 375, 375L, 375LME, Deere double strap: 550LC, 750

CATERPILLAR LOADER TIPSVERTICAL-PIN STYLE (OLD STYLE)

MODEL NO. SHORT TIP LONG TIP PIN LOCK

920, 922, 930, 931,933, 941, 944

PM4K6936 PM4K0043 PM4K0041

930, 944, 950, 951,955, 966

PM5K2925 PM4K0034 PM4K0043 PM4K0041

950, 966, 977, 980 PM5K2926 PM4K6148 PM4K0032 PM4K0008

Caterpillar - Specifications

T

20 Seriesstyle description part no. a b c d lbs.

T Fanggs dig TF1U3202 5-7/8" 1-3/4" 1-13/32" 1-27/32" 4.1

T long T1U3202 5-11/16" 2" 1-13/32" 1-27/32" 3

T tiger TT1U3202 6-1/2" point 1-13/32" 1-27/32" 3.5

T twin tiger TX1U320WT 6-1/2" 2-3/4" 1-13/32" 1-27/32" 5.5

T abrasion T4T2203 5-11/16" 2-3/16" 1-13/32" 1-27/32" 3

T penetrator T1U3209 5-11/16" 1" 1-13/32" 1-27/32" 2.4

2 adapter PM4T1204 7-1/4" 1/2" 1/2" 23° 4.63 adapter T8J7525 3-15/16" 1" 1" 23° 3.1


T long T6Y3222 6-9/16" 2-1/8" 1-3/4" 2-11/32" 3.71 adapter PM6Y3224 5-9/16" 3-11/16" 1-1/16" 22° 6.6



T Fanggs dig TF1U3252D 7-5/8" 2-1/2" 1-15/16" 2-11/16" 9

T fanggs load TF1U3252L 7-5/8" 2-1/2" 1-15/16" 2-11/16" 9

T short T1U3251 6-11/16" 2-1/4" 1-15/16" 2-11/16" 5.9

T long T1U3252 7-3/4" 2-5/8" 1-15/16" 2-11/16" 5.9

T long h-d T9N4252 8-1/8" 2-2/1" 1-15/16" 2-11/16" 10.9

T tiger TT1U3252 8-1/8" point 1-15/16" 2-11/16" 5.5


T flare T3G8250 8" 4-1/2" 1-15/16" 2-11/16" 8.5

T penetrator T9J4259 7-1/2" 1-3/8" 1-15/16" 2-11/16" 5.3

T abrasion T4T2253 7-1/2" 3-1/8" 1-15/16" 2-11/16" 7

T abrasion h-d PM9N4253 7-15/16" 3-15/16" 1-15/16" 2-11/16" 10

T ribbed sharp PM1U3252SYL 8-1/4" 2-3/4" 1-15/16" 2-11/16" 6.24 adapter T25CA 5-5/8" 1" 7-1/8" 30° 14.2

5 adapter T25EA 8-1/4" 1" 3-1/8" 30° 18.6

2 adapter T1U1254 9-1/4" 2" 1" 22° 12.1

3 adapter T3G0169 7-1/2" 2-5/16" 2" 22° 10.8

4 adapter T1U0257 2-3/4" 4-7/8" 1-1/16" 23° 18.2

6 adapter PM3G4258 5-3/4" 4-3/16" 1-1/16" 43° 25

6 adapter PM3G4259 5-3/4" 4-3/16" 1-1/16" 43° 251 adapter PM6Y3254 6-1/8" 5" 1-5/16" 22° 9.5



T Fanggs dig TF1U3302D 9" 3" 2-3/8" 3-1/32" 12.3

T Fanggs load TF1U3302L 8-3/4" 3" 2-3/8" 3-1/32" 13.3

T short T1U3301 7-5/8" 2-3/4" 2-3/8" 3-1/32" 9

T long T1U3302 8-3/4" 2-3/4" 2-3/8" 3-1/32" 9.9

T long h-d T9N4302 8-7/8" 2-3/4" 2-3/8" 3-1/32" 12.1

T tiger TT1U3302 9-3/8" 3-1/4" 2-3/8" 3-1/32" 9.2

T twin tiger TX1U3302WT 9-1/8" 4" 2-3/8" 3-1/32" 10.7

T flare T107-3300 8-1/2" 6" 2-3/8" 3-1/32" 11

T penetrator T9J4309 8-1/2" 1-1/2" 2-3/8" 3-1/32" 7.8

T abrasion T4T2303 8" 3-7/16" 2-3/8" 3-1/32" 10.8

T abrasion h-d T9N4303 8-5/16" 4-3/8" 2-3/8" 3-1/32" 16.7

T ribbed sharp PM1U3302SYL 9-1/4" 3-1/2" 2-3/8" 3-1/32" 10T rock chisel PM1U3302RC 9-7/8" 3-1/4" 2-3/8" 3-1/32" 11.84 adapter T30CA 2-5/16" 4-13/16" 1-5/16" 30° 20.8

5 adapter T30EA 10" 4-1/8" 1-1/16" 30° 21.7

1 adapter T3G6304 7-7/8" 4-3/8" 1-3/8" 22° 16.3

4 adapter T1U0307 2-3/4" 4-7/8" 1-1/16" 39° 23.1

6 adapter PM3G4308 7" 4-3/4" 1-1/16" 39° 34.9

6 adapter PM3G4309 7" 4-3/4" 1-1/16" 39° 34.9

4 adapter T4T4307 3-3/16" 6-1/2" 1-5/16" 23° 31.2

4 adapter PM3G9307 3-1/8" 6-5/16" 1-5/16" 23° 31.9

6 adapter PM3G8308 8-3/16" 5-1/2" 1-1/16" 39° 36.5

6 adapter PM3G8309 8-3/16" 5-1/2" 1-1/16" 39° 36.52 adapter PM1U1304 9-1/4" 3-3/4" 1-1/2" 23° 18.3



T Fanggs dig TF1U3352D 10" 3-3/8" 2-11/16" 3-5/16" 16.9

T short T1U3351 8-1/8" 3-1/2" 2-11/16" 3-5/16" 11.4

T long T1U3352 9-3/8" 3-1/4" 2-11/16" 3-5/16" 12.3

T long h-d T9N4352 10" 3-1/2" 2-11/16" 3-5/16" 18.7

T tiger TT1U3352 11-1/8" 3-15/16" 2-11/16" 3-5/16" 13


T flare T107-3350 9-1/2" 7" 2-11/16" 3-5/16" 16

T penetrator T9J4359 9-7/8" 2" 2-11/16" 3-5/16" 12.3

T abrasion T4T2353 9-1/2" 4" 2-11/16" 3-5/16" 17.8

T abrasion h-d T9N4353 10 5" 2-11/16" 3-5/16" 21.6

T ribbed sharp PM1U3352SYL 10 1/4" 2" 2-11/16" 3 5/16" 12.4T rock chisel PM1U3352RC 11" 3-1/2" 2-11/16" 3-5/16" 15.3T rk penetrator PM4T2353RP 11-5/8" 3-3/4" 2-11/16" 3-5/16" 231 adapter T3G8354 8-1/4" 2-11/16" 1-5/8" 35° 20.7

2 adapter PM1U1354 11-1/4" 3-3/4" 1-1/2" 22° 30.9

7 adapter PM8J5357 4-3/16" 6" 1-13/16" 23° 35.6

4 adapter T3G3357 3-7/8" 5-7/8" 1-11/16" 24° 40.3

6 adapter PM3G5358 8-17/32" 5-5/8" 1-9/16" 38° 49

6 adapter PM3G5359 8-17/32" 5-5/8" 1-9/16" 38° 49

7 adapter PM8J3357 3-1/2" 5-11/16" 1-13/16" 23° 44

4 adapter PM1U1357 4-1/8" 6-1/8" 1-3/4" 23° 45

3 adapter PM1U1350 10-1/4" 2" 1-3/4" 23° 217 adapter PM9J2357 3-3/8" 5-3/4" 1-1/2' 23° 36.4


T long T7T3402 11-1/16" 3-7/8" 3-5/32" 3-21/32" 25

T long h-d T8E4402 11-1/16" 3-7/8" 3-5/32" 3-21/32" 25

T penetrator T6Y7409 10-1/2" 2" 3-5/32" 3-21/32" 21

T penetrator PM6Y7409 11-3/8" 1-1/2" 3-5/32" 3-21/32" 17.5

T rock chisel PM7T3402RC 12" 4" 3-5/32" 3-21/32" 23.51 adapter PM7T3404 9-1/2" 6-3/4" 1-7/8" 22° 6.7



T Fanggs dig TF9W8452D 10" 3-3/8" 3-17/32" 3-29/32" 28.5

T short T9W8451 10-3/8" 4-1/2" 3-17/32" 3-29/32" 22.5

T long T9W8452 11-1/2" 4-1/2" 3-17/32" 3-29/32" 24.6

T long h-d T9N4452 13" 4-1/2" 3-17/32" 3-29/32" 36.2

T tiger PM1U3452T 13-3/16" 5-1/2" 3-17/32" 3-29/32" 20.5

T twin tiger PM1U3452WT 13-3/16" 7-1/4" 3-17/32" 3-29/32" 24.5

T flare T107-3450 11-1/4" 9" 3-17/32" 3-29/32" 31.3

T penetrator T9J4459 11-5/8" 2" 3-17/32" 3-29/32" 23.6

T abrasion h-d T9N4453 11 5/8" 5-1/2" 3-17/32" 3-29/32"

T abrasion PM9W1453 11-5/8" 5-1/2" 3-17/32" 3-29/32" 32.4

T penetrator T9J4459 11-5/8" 2" 3-17/32" 3-29/32" 23.6

T ribbed sharp PM9W8452SYL 12-1/2" 4-3/4" 3-17/32" 3-29/32" 25.1

T rock chisel PM1U3452RC 13-5/16" 4-1/2" 3-17/32" 3-29/32" 32.3

T rk penetrator PM9W1452RP 14" 4-3/4" 3-17/32" 3-29/32" 48.4

1 adapter T1U1454 11-1/8" 7-3/8" 2" 24° 42

1 adapter T8E6464 11-1/8" 7-3/8" 2" 24° 41.8

2 adapter PM8J1454 12-1/2" 4-1/8" 2-3/16" 23° 45.4

2 adapter PM9J9584 12-1/2" 4-1/8" 2-3/16" 23° 50

1 adapter PM8E3464 10-3/8" 6-7/8" 2-1/8" 22° 50

1 adapter PM8E3465 10-3/8" 6-7/8" 2-1/8" 22° 501 adapter PM8E3466 10-3/8" 6-7/8" 2-1/8" 22° 50


T short T1U3551 12-1/2" 5-1/2" 4-5/16" 4-11/32" 35.5T long T1U3552 13-1/2" 5-1/2" 4-5/16" 4-11/32" 33.5

T long h-d PM9N4552 14" 5-3/4" 4-5/16" 4-11/32" 59

T penetrator T9J4559 13-1/4" 2-5/8" 4-5/16" 4-11/32" 35

T abrasion PM9W1553 13" 9" 4-5/16" 4-11/32" 50.5

T abrasion h-d PM6Y2553 13-1/2" 7-5/8" 4-5/16" 4-11/16" 67

T rock chisel PM1U3552RC 14-3/4" 5-3/4" 4-5/16" 4-11/16" 45.5

T penetrator T9J4559 13" 2-5/8" 4-5/16" 4-11/16" 32

T rk penetrator PM9W1553RP 15-3/16" 5-3/4" 4-5/16" 4-11/16" 661 adapter PM1U1553 14-1/2" 8-5/8" 2-7/16" 23° 77.2

1 adapter PM3G9494 14-1/2" 12-5/8" 2-5/8" 22° 70

1 adapter PM3G9495 15" 13-3/8" 2-5/8" 22° 701 adapter PM3G9496 15" 13-3/8" 2-5/8" 22° 70



T long T4T4702 16-5/16" 7 6 5-3/4" 84T abrasion T4T4703 16-5/16" 9 6 5-3/4" 107.21 adapter T4T4704 12-3/4" 16-3/4" 3" 22° 149

John Deere Replacement Teeth for Esco Conical Products

John Deere replacement teeth for Esco conical systems come in sizes and toothdesigns to fit almost all machine makes and models.

Conical DesignThe "conical" design mating systembetween tooth and adapter createsself-tightening action. The raisedcenter area on the top and bottom ofthe adapter nose piece fits tightly intothe formed area on the top and bottomof the tooth pocket. This designreduces tooth movement both verticallyand horizontally. The tooth andadapter are designed as a bucket toothsystem that will absorb impact loadsand generally reduce the amount ofabrasive action to the bucket lip.

Pin and Lock RetentionAll John Deere replacement teeth forEsco conical products are retained witha pin and lock. Once the pin and lockare installed, a snug fit gives thisattaching system little to no movementand provides great strength throughoutthe life of the tooth. We offer pins andlocks in the standard and ratchetversion. The standard is designed foruse in general-purpose applications.The ratchet style provides secureretention in more demandingconditions and avoids "pin walk" inheavy prying conditions.

Part Number Explanation (Replacement Teeth for Esco Products)Prefix Suffix ExplanationPM TF Dual Purpose FlarePM TL Dual Purpose LongT AP Abrasion PaneledT R RockT S SharpT S_F Sharp_" FlareT TVIP or TVIPA Twin "V-Shaped" Paneled

(Twin Tiger)T VIP or VIPA "V-Shaped" Paneled

(Tiger)

NOTES: Nose Sizesare identified by thefirst two numericdigits of thedesignation number.The letter(s) followingthe nose size describethe tooth shape.

Examples:Part Number T30S Esco Replacement, 3.0 inches wide, sharp.Part Number T25S5F Esco Replacement, 2.5 inches wide, sharp, 5" flare.

John Deere Replacement Teeth for Esco Conical Products - TypesAvailable

Abrasion-Paneled Teeth(AP Suffix) (Centerline)

• Good for general-purpose-to-to heavy-dutyapplications.

• Good penetration; selfsharpens.

Flare Teeth (S_F Suffix)(Centerline)

• For loading and digging inloose, mud-like conditions.

Sharp Teeth (S Suffix)(Centerline)

• Slim, penetrating profile.For use in general-purpose toheavy digging and loadingconditions.

Tiger Teeth(VIP or VIPA Suffix)(Non-Centerline)

• V-shaped and paneled for high-impact digging and loading.

• Narrow bit for maximumpenetration; paneled to maintainsharpness.

Twin Tiger Teeth(TVIP or TVIPA Suffix)(Non-Centerline)

• Two points on the V-shapedtooth cut clearance for bucketsides.

• Can be used as center teeth formaximum penetration.

Esco Conical - Teeth by Series

18 Series Conicalstyle description part no. rcv. disc. non stock used on

a sharp PM18SLHX STKc tiger PM18VIPHX STKb twin tiger PM18TVIPHX STK

tilt front PM18THX STKlong PM18TL STK

- std pin PM18PN STKpin PM18-20MPNP STK

- std retainer PM18LK STK- adapter PM833-18 STK

tooth, long PM18LPHX STKrubber lock PM18-20MLKR STKadpt., W-O, bttm. leg, 1.25" lip PM855-18HX N.S.adpt., B-O, 1-1/2 leg, (Case W18, W20) PM4718-18HX N.S.adpt., B-O, 2 leg, (Case 850B) PM4729-18HX N.S.adpt., B-O, crnr., RH (Case 850B) PM5701R-18HX N.S.adpt., B-O, crnr., LH (Case 850B) PM5701L-18HX N.S.adpt., B-O, 1-1/2 leg, 1.06" thr PM5707-18HX STK


a sharp T25S STKc tiger T25VIP STKb twin tiger T25TVIP STKd flare, 5" T25S5F STKd d-p flare PM25TF STK- std pin T2530PN STK- std retainer T2530LK STK- ratchet pin T2530PNR STK- ratchet retainer T2530LKR STK- adpt., W-O, bttm., leg, 1.25 lip, 30 degrees PM855-25 STK- adapter PM3806-25 STK

tooth, tilt front PM25THX STKpin, solid PM25RP STKrubber bushing PM25RB STKsteel bushing PM25RBS STKadpt., B-O, 1-1/2 leg, (Case 1150) PM4703-25HX N.S.adpt., B-O, crnr., LH PM5710L-25HX N.S.adpt., B-O, crnr., RH PM5710R-25HX N.S.nose, W-O PMEWN25 STK

Competitive: Backhoes

JD: 190E, 290D, Competitive: Backhoes, Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers



a sharp T30S STKc tiger T30VIP STKb twin tiger T30TVIP STKd flare, 6" T30S6F STK- std pin T2530PN STK- std retainer T2530LK STK- ratchet pin T2530PNR STK- ratchet retainer T2530LKR STK- adapter PM3807-30 STK- adapter TH108948 STK- adapter TH103467 STK

tooth, tilt front PM30THX STKadpt., W-O, bttm. leg, 1.25" to 1.5" lip PM838-30HX STKadpt., W-O, bttm. leg, 1.5" lip PM855-30HX STKadpt. nose, W-O PMEWN30 N.S.


a sharp T35S STKc tiger T35VIPA STKb twin tiger T35TVIPA STKd flare, 6" T35S6F STK- adapter PM3808-35 STK- std pin T35PN STK- std retainer T3540LK STK- ratchet pin T35PNR STK- ratchet retainer T3540LKR STK- adapter EX119-35 STK- spool EX20SP STK- wedge EX20W2 STK- wedge EX20W3 STK- wedge EX20W1 STK

adpt., stake-type, for C-19 Hensley PM136-35HX N.S.flex pin for C-19 Hensley lips (136-35HX) PMP136 STKadpt., W-O, bttm. leg, 1.5" lip PM822-35HX N.S.adpt., W-O, bttm. leg, 1.5" to 1.75" lip PM839-35HX N.S.adpt., W-O, 1-1/2 leg, 1.5" lip PM1899-35HX STKadpt., W-O, 1-1/2 leg, 1.25" lip PM1875-35HX STKadpt., nose, W-O PMEWN35 N.S.


a sharp T40S STKc tiger T40VIPA STKb twin tiger T40TVIP STKd flare T40S7F STK- adapter PM3809-40 STK- adapter TH111281 STK- adapter TH109817 STK- adapter TH102450 STK- std pin T40PN STK- std retainer T3540LK STK- ratchet pin T40PNR STK- ratchet retainer T3540LKR STK

adpt., stake-type, for Hensely lips PM236-40HX N.S.adpt., stake-type, for C-29 ESCO lips PM129-40HX STKflex pin for C-29 Hensley lips (236-40) PMP236 STKadpt., nose, W-O PMEWN40 STK

JD: 490, 490D, 490E, 495D, 590D, 595, 595D, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

JD: 690, 690A, 690B, 690C, 690D, 690E, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

JD: 790, 790D, 790E, 792, 792D, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

Esco Conical - Teeth by Series45 Series Conicalstyle description part no. rcv. disc. non stock used on

a sharp T45S STKc tiger T45VIPA STKb twin tiger T45TVIP STKd flare, 8" T45S8F STK

tooth, long PM45LPHX N.S.tooth, rock chisel PM45RDXHX STK

- adapter AT131709 STK- std pin T45PN STK- std retainer T45LK STK- ratchet pin T45PNR STK- ratchet retainer T45LKR STK- adpt., stake-type, ESCO C-29 lip EX129-45 STK- spool EX29SP STK- wedge EX29W1 STK- wedge EX29W2 STK- wedge EX29W3 STK

adpt., stake-type, ESCO C-29 lip PM129-45HX STKflex pin for C-29 ESCO lips (236-40) PMP236 STKadpt., stake-type, Hensley C-29 PM236-45HX N.S.flex pin for C-29 Hensley lips (236-40) PMP236 STKadpt., W-O bttm. leg PM840-45HX N.S.adpt., W-O 1-1/2 leg 2" lip PM2810-45HX STKadpt., nose, W-O PMEWN45 N.S.


a sharp PM50SHX STKa long sharp PM50SLHX N.S.c tiger PM50VIPHX STKb twin tiger PM50TVIPHX N.S.

rock PM50RHX N.S.rock chisel PM50RDXHX STKabrasion panel PM50APHX N.S.flare, 9" PM50S9FHX N.S.long PM50LPHX N.S.

- pin PM50PNP STK- rubber lock PM50LKR STK- ratchet pin PM50PNRP STK- ratchet rub lock PM50LKRR STK

adpt., W-O, 1-1/2 leg, 2.25 lip, 30 degrees PM3811-50HX N.S.adpt., nose, W-O PMEWN50 N.S.


a sharp PME55HX N.S.a sharp short PM55SSHX N.S.a sharp long PM55LPHX STKc tiger PM55VIPHX N.S.b twin tiger PM55TVIPHX N.S.

rock PM55RHX STKrock chisel PM55RDXHX STKabrasion panel PM55APHX N.S.

d flare, 10" PM55S10FHX N.S.slag PM55AHX N.S.heavy slag PM55AHHX N.S.panel sharp PM55SPHX N.S.

- pin PM55PNP STK- ratchet pin PM55PNRP STK- wedge pin PM55PNTP STK- rubber lock PM55LKR STK- ratchet rub lock PM55LKRR STK

adpt., W-O, 1-1/2 leg, 3 straight lip, 23 degre PM1856-55HX N.S.adpt., nose, W-O PMEWN55 N.S.

JD: 890, 890A, 892D, 892E, 992D, 992E, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers


Early "R" Series Conicalstyle description part no. rcv. disc. non stock used on

tooth PMR2HX STKpin PMR2P STKrubber plug PMR2R STKadpt., W-O, bttm. leg, 1.25" lip PMCB11255R2H STK

Esco Super Conical- Applications

36 Series Super Conicalstyle description part no. rcv. disc. non stock used on

flared panel PM36FPHX STKtilt front PM36THX N.S.

c tiger PM36VIPHX N.S.- lock PM36LKR STK- pin PM36PNP STK


long rock PM46ARLHX N.S.rock PM46RHX STKflared panel PM46FPHX STKtilt front PM46THX N.S.

c tiger PM46VIPHX N.S.- lock PM46LKR STK- pin PM46PNP STK


long rock PM56ARLHX N.S.d flared panel PM56FPHX N.S.

rock PM56RHX N.S.c tiger PM56VIPHX N.S.- lock PM56LKR STK- pin PM56PNP STK

Sidecuttersstyle description part no. rcv. disc. non stock used on

sidecutter, LH, 4" add'1 PMT1154CHX STKsidecutter, RH, 4" add'1 PMT1155CHX STKsidecutter, LH, 2" add'1 PMT2143AHX N.S.sidecutter, RH, 2" add'1 PMT2144AHX STKsidecutter, LH, 6" add'1 PMT1156AHX STKsidecutter, RH, 6" add'1 PMT1157AHX STKsidecutter, strikeoff PMPDE31329HX STK

Esco Ripper Teeth- Applications

22 Seriesstyle description part no. rcv. disc. non stock used on

tooth, ripper PM22R10HX STKbushing PM22RBGB STKpin PM22RPGP STK


tooth, ripper PM25R11HX STKtooth, ripper PM25R12HX STKripper, nose, W-O PM25RNHX STKtooth, ripper EX25R12 STK

Competiitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders,

Scrapers, Shovel Dippers















ripper tooth T35-5R15 STKtooth, ripper 14 PM35R14HX STKtooth, ripper 15 PM35R15HX STKtooth, ripper 15 PM35R15AHX STKtooth, ripper, tiger, 15 PMT35R15 N.S.tooth, ripper, twin tiger, 14 PM35RWTHX N.S.bushing, rubber PM35RB STKbushing, slag PM35RBS STKpin, solid PM35RP STK


tooth, ripper PM39-5R17AHX STKpin PM39RP STK

bushing PM39RB STK





Esco Conical - Specifications

18 Series Conicalstyle description part no. a b c d lbs.

T long PM18TL 4-11/16" 2-1/8" 1-13/16" 1-1/2" 3.1T sharp PM18SLHX 5-7/8" 2-1/8" 1-13/16" 1-1/2" 1.9T tilt front PM18THX 4-13/16" 2-3/16" 1-13/16" 1-1/2" 1.8T tiger PM18VIPHX 6-7/8" 3/8" 1-13/16" 1-1/2" 2.5T twin tiger PM18TVIPHX 6-7/8" 3" 1-13/16" 1-1/2" 34 adapter PM833-18 - 3/4" 3-7/8" 23° 3.3

tooth, long PM18LPHX 2.1pin PM18-20MPNP 0.1rubber lock PM18-20MLKR 0.1tooth, ripper PM22R10HX 8adpt., W-O, bttm. Leg, 1.25" lip PM855-18HX 4.2adpt., B-O, 1-1/2 leg, (Case W18, W20) PM4718-18HX 6.6adpt., B-O, 2 leg, (Case 850B) PM4729-18HX 8.5adpt., B-O, crnr., RH (Case 850) PM5701R-18HX 12adpt., B-O, crnr., LH (Case 850) PM5701L-18HX 12adpt., B-O, 1-1/2 leg, 1.06" thr PM5707-18HX 6.5


T sharp T25S 6-5/8" 2-1/2" 2-1/2" 2-1/8" 5.6T tiger T25VIP 8-1/8" 1/8" 2-1/2" 2-1/8" 6.9T twin tiger T25TVIP 8" 3-1/4" 2-1/2" 2-1/8" 7.4T flare, 5" T25S5F 6-1/2" 4-7/8" 2-1/2" 2-1/8" 7.4T d-p flare PM25TF 6-5/16" 3-5/16" 2-1/2" 2-1/8" 6.04 adapter PM855-25 - 1" 5-1/4" 23° 7.32 adapter PM3806-25 - - - 20° 10.5

tooth, tilt front PM25THX 4.8adpt., B-O, 1-1/2 leg, (Case 1150) PM4703-25HX 12.5adpt., B-O, crnr., LH PM5710L-25HX 12.8adpt., B-O, crnr., RH PM5710R-25HX 12.5nose, W-O PMEWN25 11/16" 3-1/16" 2-7/8" - 4.9

Type 4

T



T sharp T30S 6-1/2" 3-1/8" 3" 2-1/4" 6.6T tiger T30VIP 8-1/4" 1/8" 3" 2-1/4" 7.2T twin tiger T30TVIP 8-1/4" 3-3/4" 3" 2-1/4" 9.3T flare, 6" T30S6F 6-5/8" 6" 3" 2-1/4" 8.52 adapter PM3807-30 6-1/2" 1-1/4" 6" 23° 17.01 adapter TH108948 3-1/2" 1-5/16" 8" 25° 13.91 adapter TH103467 4-14" 1-5/16" 9-7/8" 15° 17.5

tooth, tilt front PM 30THX 6.0adpt., W-O, bttm. leg, 1.25" to 1.5" lip PM 838-30HX 11.1

adpt., W-O, bttm. leg, 1.5" lip PM 855-30HX 9.2nose, W-O PMEWN30 3/4" 3-1/8" 3-3/8" - 5.6


T sharp T35S 7-3/4" 3-5/8" 3-1/2" 2-5/8" 10.6T tiger T35VIP 10/7/2016 1/8" 3-1/2" 2-5/8" 6.9T twin tiger T35TVIPA 10" 4-1/4" 3-1/2" 2-5/8" 11.2T flare, 6" T35S6F 7-3/4" 6" 3-1/2" 2-5/8" 11.72 adapter PM3808-35 6-1/4" 1-5/8" 5-3/4" 23° 19.43 adapter EX119-35 6-1/4" 1-5/8" 6-1/4" 13° 17.1

adpt., stake-type, for C-19 Hensley PM136-35HX 19.4adpt., W-O, bttm. leg, 1.5" lip PM822-35HX 25.0adpt., W-O, bttm. leg, 1.5" to 1.75" lip PM839-35HX 22.1adpt., W-O, 1-1/2 leg, 1.5" lip PM1899-35HX 22.6adpt., W-O, 1-1/2 leg, 1.25" lip PM1875-35HX 20.6nose, W-O PMEWN35 3/4" 3-5/8" 4" - 9.4


T sharp T40S 9" 4-1/4" 4" 3" 14.5T tiger T40VIPA 12-5/16" 1/4" 4" 3" 15.4T twin tiger T40TVIP 10" 4-3/4" 4" 3" 16.6T flare T40S7F 8-3/4" 6-5/8" 4" 3" 15.12 adapter PM3809-40 7-1/2" 1-5/8" 7" 23° 33.11 adapter TH111281 4" 1-5/8" 8-3/4" 17° 26.01 adapter TH109817 4" 1-1/2" 8-3/4" 18° 27.21 adapter TH102450 6-1/4" 1-5/8" 10-3/4" 43° 28.4

adpt., stake-type, for Hensley PM236-40HX 43.8adpt., stake-type, for C-29 ESCO lips PM129-40HX 27.0nose, W-O PMEWN40 1" 4-1/4" 4-1/2" - 13.7



T sharp T45S 10" 4-5/8" 4-1/2" 3-1/4" 20.8T tiger T45VIPA 13-3/4 1/4" 4-1/2" 3-1/4" 22.9T twin tiger T45TVIP 11" 5-1/2" 4-1/2" 3-1/4" 24.8T flare, 8" T40S8F 9-7/8" 7-3/4" 4-1/2" 3-1/4" 25.2

tooth, long PM45LPHX 16.4tooth, rock chisel PM45RDXHX 17.7

2 adapter AT131709 7-1/4" 2-1/4" 7-1/4" 25° 44.03 adpt., stake-type, ESCO C-29 lip EX129-45 9" 2-1/2" 9" 17° 33.3

adpt., stake-type, ESCO C-29 lip PM129-45HX 32.7adpt., stake-type, Hensley C-29 PM236-45HX 48.5adpt., W-O bttm. leg PM840-45HX 35.1adpt., W-O 1-1/2 leg 2" lip PM2810-45HX 45.2nose, W-O PMEWN45 1-1/16" 4-1/2" 5" - 17.9


T sharp PM50SHX 11-1/8" 5-11/16" 4-7/8" 3-13/16" 22.4T long sharp PM50SLHX 11-1/8" 5-1/4" 4-7/8" 3-13/16" 23.0T tiger PM50VIPHX 15" 5/8" 4-7/8" 3-13/16" 31.6T twin tiger PM50TVIPHX 13" 6-1/2" 4-7/8" 3-13/16" 34.8T rock PM50RHX 10-5/8" 5-1/4" 4-7/8" 3-13/16" 23.7T rock chisel PM50RDXHX 12" 3" 4-7/8" 3-13/16" 20.3T abrasion panel PM50APHX 11-3/4" 5-3/4" 4-7/8" 3-13/16" 30.9T flare, 9" PM50S9FHX 11" 9" 4-7/8" 3-13/16" 28.8T long PM50LPHX 11-15/16" 5-1/8" 4-7/8" 3-13/16" 26.9

adpt., W-O, 1-1/2 leg, 2.25 lip, 30 degrees PM3811-50HX 60.4nose, W-O PMEWN50 1-3/8" 5-5/16" 5-1/16" - 23.7


tooth, std. PME55HX 27.4T sharp short PM55SSHX 10-5/16" 6" 5-3/8" 4-1/4" 25.9T sharp long PM55LPHX 13-1/4" 6" 5-3/8" 4-1/4" 36.1T tiger PM55VIPHX 16-1/2" 3/4" 5-3/8" 4-1/4" 43.1T twin tiger PM55TVIPHX 15-1/2" 7" 5-3/8" 4-1/4" 51.2T rock PM55RHX 11-1/8" 6" 5-3/8" 4-1/4" 31.5T rock chisel PM55RDXHX 13-1/2" 3-3/8" 5-3/8" 4-1/4" 31.9T abrasion panel PM55APHX 12-3/4" 6-1/2" 5-3/8" 4-1/4" 39.0T flare, 10" PM55S10FHX 11-1/4" 10" 5-3/8" 4-1/4" 35.0T abrasion PM55AHX 11-3/8" 6" 5-3/8" 4-1/4" 34.6T heavy slag PM55AHHX 12-3/16" 6" 5-3/8" 4-1/4" 44.6T panel sharp PM55SPHX 12" 5-1/2" 5-3/8" 4-1/4" 31.5

adpt., W-O, 1-1/2 leg, 3 straight lip, 23 degrees PM1856-55HX 81.0nose, W-O PMEWN55 31.2


Early "R" Series Conicalstyle description part no. a b c d lbs.

tooth PMR2HX 3.0rubber plug PMR2R 0.1Adpt., W-O, bttm. leg, 1.25" lip PMCB11255R2H 5.5

Esco Super Conical - Specifications

style description part no. a b c d lbs.T flared panel PM36FPHX 8-3/4" 3-3/4" 2-5/16" 2-3/8" 7.8T tilt front PM36THX 8" 4" 2-5/16" 2-3/8" 8.6T tiger PM36VIPHX 10" 7/16" 2-5/16" 2-3/8" 8.1

46 Series Super Conicalstyle description part no. a b c d lbs.

T long rock PM45ARLHX 11-7/8" 5" 2-3/4" 3-3/16" 25.7T rock PM46RHX 10-1/8" 3-3/4" 2-3/4" 3-3/16" 16.7T flared panel PM46FPHX 17.8T tilt front PM46THX 10-1/2" 4-1/4" 2-3/4" 3-3/16" 17.8T tiger PM46VIPHX 12-7/8" 5/8" 2-3/4" 3-3/16" 17.4

56 Series Super Conicalstyle description part no. a b c d lbs.

T long rock PM56ARLHX 14-1/2" 6-1/4" 3-3/8" 4-3/16" 49.5T flared panel PM56FPHX 14" 5-1/2" 3-3/8" 4-3/16" 36.0T rock PM56RHX 12-3/4" 4-1/2" 3-3/8" 4-3/16" 31.4T tiger PM56VIPHX 15-1/2" 5/8" 3-3/8" 4-3/16" 36.2

Sidecuttersstyle description part no. a b c d lbs.

sidecutter, LH, 4" add"1 PMT1154CHX 53.5sidecutter, RH, 4" add"1 PMT1155CHX 54.8sidecutter, LH, 2" add"1 PMT2143AHX 43.6sidecutter, RH, 2" add"1 PMT2144AHX 44.4sidecutter, LH, 6" add"1 PMT1156AHX 59.0sidecutter, RH, 6" add"1 PMT1157AHX 59.5sidecutter, strikeoff PMPDE31329HX 37.0adpt. nose, W-O PMEWN25 4.9

36 Series Super Conical


Esco Ripper Teeth- Specifications


tooth, ripper PM22R10HX 8.0


tooth, ripper PM25R11HX 11.0tooth, ripper PM 25R12HX 13.1ripper, nose, W-O PM 25RNHX 18.1


tooth, ripper 14 PM35R14HX 26.0tooth, ripper 15 PM35R15HX 27.1tooth, ripper 15 PM35R15AHX 29.0tooth, ripper, tiger, 15 PMT35R15 30.0tooth, ripper, twin tiger, 14 PM35RWTHX 31.8ripper tooth T35-5R15 30.4


tooth, ripper PM39-5R17AHX 43.6

Replacements for Esco Conical Products Retainers

Esco Conical13


PM18LK - 18 Series

T2530LKR - 25 and 30 Series

T3540LKR - 35 and 40 Series

T45LKR - 45 Series

T2530LK - 25 and 30 Series

T3540LK - 35 and 40 Series

T45LK - 45 Series


Replacements for Esco Conical Products Retainers (Continued)

Esco Conical14


T45PN45 SeriesT45PNR



T2530PN25 and 30 Series

T2530PNR25 and 30 Series

PM18PN18 Series


Esco Helilok®/Vertalok® Systems

Style a Style b Style c

Standard Teeth (SYL Suffix)(Centerline)

Tiger Teeth (VIP Suffix)(Non-Centerline)

Twin Tiger Teeth (TVIP Suffix)(Non-Centerline)

• For general-purpose to heavy-duty digging and loading

• Excellent penetration and wear

• High penetration for frost andtough material

• For digging and loading inextremely tight material

• Use as a corner tooth with tigerteeth in the center

Style d Style e

Flare Teeth (S_F Suffix)(Centerline)

Chisel Teeth (SD Suffix)(Centerline)

• For digging in mud-likeconditions

• Wide bite for trench cleanup

• Chisel shape with sharp profile• Excellent penetration• Greater wear than tiger or twin

tiger teeth

Part Number Explanation for Esco Helilok®/Vertalok® TeethPrefix Suffix ExplanationEX ARL AbrasionEX SD ChiselEX S_F Flare (S5F indicates a sharp edge with a 5" flare)EX SYL StandardEX VIP TigerEX TVIP Twin Tiger

Esco Helilok® Vertalok® SystemHelilok/Vertalok teeth are designed to give you upto 20% more wear material up-front over othertooth systems. As a result, more time can be spentdigging and loading rather than replacing teeth.

Teeth mount on both the Vertalok and Helilokadapters with a quarter turn and butt up against theadapter nose to take thrust loads head-on. Thehelical threads and large stabilizing flats at the endof the nose deliver maximum resistance to severebreakout forces. Digging forces are distributedover the entire nose surface which results in addedstrength and durability.

With Quadrilok, the helical threads create a "locknut" force to resist shockloads and keep point securely locked.

Loading stresses are distributed over the entire nose for unmatchedresistance to breakout and digging forces.

Greater strength and load bearing area.

Point twists onto the adapter with a quarter turn.

Helilok® Vertalok® Adapters

Horn Style 1 1/2 (Top Leg) 1 1/2 (Bottom) Leg

Available for Esco Horn-style lips Extra strength and weld surface fortough digging conditions

Fits a wide range of lip thicknesses.Designed for general-purpose use -backhoes - excavators

Side Cutter Spherical

Tooth-type side cutters cut extra clearance Designed for Esco S19 and S29 series bucket lips

Esco Helilok®/Vertalok® Systems Retainers

Quadrilok® (For Helilok® Adapters) Pin and Plug (For Vertalok® Adapters)

Quadrilok® Retainer for Helilok® Adapters Pin and Plug for Vertalok® Adapters

Teeth are held on to Helilok® adapters by a drive-on, one-piece Quadrilok® retaining system. Withthe Quadrilok, the helical threads create a lock-nutforce that tightens under load and resists rotationunder the most severe impact.

The U-shaped Quadrilok eliminates the need forsnap rings or rubber-bonded locks, and it preventsthe tooth from rotating.

Teeth are securely fastened to Vertalok adapterswith a drive-through pin which providesmaximum holding power and virtually eliminatestooth loss.

The pin is held in place by a spring-loaded plugthat fits snugly into a cavity in the side of theadapter nose. Both the pin and the plug arereusable provided they are not damaged.

Pins can be removed with a pin or punch.

Special Tools for Quadrilok® AdaptersFor removal and installation of the 21 and 27 Series Teeth, use special tool EX21-27QRT.For the 37, 47, and 57 Series, use special tool EX3-4-57QRT.

Special tools for Vertalok® AdaptersFor removal and installation of 37, 47 and 57 series Vertalok teeth, use special tool EXPRT

Spool and Wedge Adapter Locks for Horn Style Adapters: Install a spool in front of the key slot and a wedge in the rearof the key slot. Oversize wedges are available to compensate for wear. Use a standard wedge (W1) when installing a newadapter on a new or reconditioned lip. When the W1 is nearly flush with the top of the lip, replace it with a W2 wedge.When the W2 wedge drives flush, replace it with a W3 wedge. To avoid lip damage, rebuild the adapter promptly when aW3 drives flush with the top of the lip.

Fluted WedgeSeries Fluted Spool W1 W2 W3

21 or 27 EX20SP EX230W1 EX20W2 EX20W337 EX29SP EX29W1 EX29W2 EX29W3

Side Wear Shroud (bolt-on)

A B Weight

EX31329-X 3.95 5.97 40

Esco Helilok® / Vertalok® Products RetainersQuadrilok® for Helilok® AdaptersIllustrated parts are actual size

EX21LKS21 Series

EX37LKS37 Series

EX27LKX27 Series

Esco Helilok®Vertalok® Products Retainers

Quadrilok® for Helilok® Adapters; Pins for Vertalok® AdaptersIllustrated parts are actual size

EX57LKS57 Series

EX27VPL27 Series

EX37VPL37 Series

EX47VPL47 Series

EX57VPL57 Series

Esco Helilok®Vertalok® Products RetainersQuadrilok® for Helilok® Adapters

EX47LKS47 Series

EX57VPN57 Series

EX47VPN47 Series

EX37VPN37 Series

EX27VPN27 Series

Illustrated partsare actual size

T

7

17 Seriesstyle description part no. a b c d lb

T standard EX17TL 5-1/2" 1-7/8" 1-1/2" 1-3/4" 2.3


T standard EX21SYL 7-1/2" 3" - - 6.7T tiger EX21VIP 7-1/8" 1/4" - - 5.9T twin tiger EX21TVIP 7-1/8" 3-1/4" - - 7.2T 5" flare EX21S5F 7-1/2" 5" - - 10.43 adapter EX119-21 1-5/8" 5-7/8" 1-5/8" 1-1/4" 15.47 adapter EX360-21 2-1/2" 2-3/8" 3-7/8" 4-3/4" 15.04 adapter EX1550-21 4-5/8" 6" 3-7/8" - 21.84 adapter EX1551-21 4-5/8" 6" 3-7/8" - 21.7

ESCO Helilok®/Vertalok® - Specifications


Esco Helilok®/Vertalok® - Tooth by Series


a standard EX17TL ü Competitive: backhoes, mini-excavators


a standard EX21SYL üc tiger EX21VIP üb twin tiger EX21TVIP üf 5" flare EX21S5F ü- Quadrilok EX21LKS ü- adapter EX119-21 ü- adapter EX360-21 ü- adapter EX1550-21 ü- adapter EX1551-21 ü- adapter EX5854-21 ü- adapter EX5849-21 ü

27 Seriesstyle description part no. used on

a standard EX27SYL üc tiger EX27VIP üb twin tiger EX27TVIP üf 6" flare EX27S6F üd chisel EX27SD üe HD Sharp EX27S ü

JD: 190E, 290D, 490, 490D, 490E, 495D Competitive: backhoes, excavators

JD: 590D, 595, 595D, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D Competitive: backhoes, excavators Case: 9030; Cat: EL180, EL200B, 215D, EL240B, All B and S family, EL180, EL200B, EL240B, Daewoo: DH130, DH170, DH180, DH200, Dresser: 545, Fiat-Allis: FX150, FX200, Gradall: Tracksta, Hyundai: R130, R200, JCB: 818, 820, Kawasaki: 90ZIII, Kobelco: SK200IV, SJ229IV, Koehring: 6612, 6615, 6620, Komatsu, PC200-6, PC210-6, WA380-1. WA400-1, WA450-


- Quadrilok EX27LKX ü- adapter EX119-27 ü- adapter EX360-27 ü- adapter EX1550-27 ü- adapter EX1551-27 ü- adapter EX5827-27 ü- pin EX27VPN ü- plug EX27VPL ü- adapter EX5850-27V ü


a standard EX37SYL üc tiger EX37VIP üb twin tiger EX37TVIP üf 7' flare EX37S7F üf 8' flare EX37S8F üd Chisel EX37SD üe HD Sharp EX37SH ü- Quadrilok EX37LKS ü

- adapter EX450-37 ü- adapter EX5824-37 ü- adapter EX1506-37 ü- adapter EX1507-37 ü- pin EX37VPN ü- plug EX37VPL ü

adapter EX5856-37V ü


a standard EX47SYL üc tiger EX47VIP üb twin tiger EX47TVIP üf 9' flare EX47TS9F üd chisel EX47SD üe HD Sharp EX47SH ü- Quadrilok EX47LKS ü- adapter EX450-47 ü- adapter EX1829A-47 ü- pin EX47VPN ü- plug EX47VPL ü- adapter EX5857-47V ü

JD:690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 892D, 892E, 922D, 922E, Case: 9040, 9050, Caterpillar: 225D, 231D, 980F, 988F, All C , D, E Family, EL300B, Competitive: Excavators, Daewoo: DH220, DH280, DH320, Dresser: 555,560B, Fiat-Allis: FX220, FX300, Hyundai: R280, R290, R320, 95ZIII, 110III, Kobelco: SK300IV, Koehring: 6625, 6627, 6633, Komatsu: PC220-6, PC250-6, PC300-5, Liebherr: R932, R942, Link-Belt: LS3400Q, LS4300Q, MDI/Yutani: MD300LC, MD320BLC, O&K Trojan, RH11, RH12, Samsung: SE280, SE350, VME: L190B, L270B, Yutani: 320BLC

JD: 892D, 892E, 992D, 992E, 9060, Caterpillar: 235C, 245B, All F, G Family, EL450, Competitive: Loaders, Daewoo: DH450, Demag: H40, Dresser: 570, Fiat-Allis: FX400, Hyundai: R450, Kawasaki: 115ZIII, Kobelco: SK400IV, SK600IV, Koehring: 6644, Komatsu: PC400-5, WA600-1, Liebherr: R952, R954, R962, Link-Belt: LS5800CII, MDI/Yutani: MD400LC, MD450BLC, O&K Trojan: RH18, RH20, Samsung: SE450,

JD: 590D, 595, 595D, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D Competitive: backhoes, excavators Case: 9030; Cat: EL180, EL200B, 215D, EL240B, All B and S family, EL180, EL200B, EL240B, Daewoo: DH130, DH170, DH180, DH200, Dresser: 545, Fiat-Allis: FX150, FX200, Gradall: Tracksta, Hyundai: R130, R200, JCB: 818, 820, Kawasaki: 90ZIII, Kobelco: SK200IV, SJ229IV, Koehring: 6612, 6615, 6620, Komatsu, PC200-6, PC210-6, WA380-1. WA400-1, WA450-2, WA500-1, Liebherr: R912, R922, Link-Belt: LS2700Q, LS2800Q, MDI/Yutani: MD200BLC, MD240BLC, MD240LC, O&K Trojan: RH8, RH9, Samsung: SE210, L160, Yutani: MD200C, MD240C


a standard EX57SYL üc tiger EX57VIP üb twin EX57TVIP ü- pin EX57VPN ü- plug EX57VPL ü- Quadrilok EX57LKS ü- adapter EX1856A-57V ü

Caterpillar: 245B, 245BLC, 245ME, 922, 922C, Competitive: Loaders, Demag: H55, H65, H85, H121, Kobelco: SK400IVME, Komatsu: PC650-3, WA700-1, WA800-2, Liebherr: R962, R972, R972HD, R974, R981, R982, Link-Belt: LS7400CII, MDI/Ytani: SK400, O&K Trojan: RH30C, RH30D, RH40C, VME: 480, L320, L480

MACHINE APPLICATION FOR HELILOK/VERTALOK SYSTEMS

Company Equipment Series

Demag H40-------------------------------------------------------------------------------47H55, H65, H85, H121---------------------------------------------------------57

Dresser 545 -------------------------------------------------------------------------------27555, 560B -----------------------------------------------------------------------37570 -------------------------------------------------------------------------------47

Fiat-Allis FX150, FX200------------------------------------------------------------------27FX220, FX300------------------------------------------------------------------37FX400 ---------------------------------------------------------------------------47

Gradall Tracksta -------------------------------------------------------------------------27

Hyundai R130, R200 ---------------------------------------------------------------------27R280, R290, R320 -------------------------------------------------------------37R450 -----------------------------------------------------------------------------47

JCB 818, 820 -------------------------------------------------------------------------27

Kawasaki 90ZIII----------------------------------------------------------------------------2795ZIII, 110ZIII -----------------------------------------------------------------37115ZIII --------------------------------------------------------------------------47

Kobelco SK200IV, SK220IV -----------------------------------------------------------27SK300IV ------------------------------------------------------------------------37SK400IV ------------------------------------------------------------------------47SK400IVME--------------------------------------------------------------------57SK600IV ------------------------------------------------------------------------47

Koehring 6612, 6615, 6620---------------------------------------------------------------276625, 6627, 6633---------------------------------------------------------------376644------------------------------------------------------------------------------47

Komatsu PC200-6, PC210-6-------------------------------------------------------------27PC220-6, PC250-6, PC300-5-------------------------------------------------37PC400-5 -------------------------------------------------------------------------47PC650-3 -------------------------------------------------------------------------57WA380-1, WA400-1, WA450-2, WA500-1 -------------------------------27WA600-1------------------------------------------------------------------------47WA700-1, WA800-2 ----------------------------------------------------------57

Liebherr R912, R922 ---------------------------------------------------------------------27R932, R942 ---------------------------------------------------------------------37R952, R954 ---------------------------------------------------------------------47R962 -----------------------------------------------------------------------------47

57R972, R972HD, R974, R981, R982 -----------------------------------------57

MACHINE APPLICATION FOR HELILOK/VERTALOK SYSTEMS

Company Equipment Series

Link-Belt LS2700Q, LS2800Q-----------------------------------------------------------27LS3400Q, LS4300Q-----------------------------------------------------------37LS5800CII ----------------------------------------------------------------------47LS7400CII ----------------------------------------------------------------------57

MDI/Yutani MD200BLC, MD240BLC, MD240LC -------------------------------------27MD200C, MD240C------------------------------------------------------------27MD300LC-----------------------------------------------------------------------37MD320BLC---------------------------------------------------------------------37MD400LC, MD450BLC ------------------------------------------------------47SK400 ---------------------------------------------------------------------------57

O&K Trojan RH8, RH9 -----------------------------------------------------------------------27RH11, RH12 --------------------------------------------------------------------37RH18, RH20 --------------------------------------------------------------------47RH30C, RH30D, RH40C -----------------------------------------------------57

O&K Trojan RH8, RH9 -----------------------------------------------------------------------27RH11, RH12 --------------------------------------------------------------------37RH18, RH20 --------------------------------------------------------------------47RH30C, RH30D, RH40C -----------------------------------------------------57

Samsung SE210----------------------------------------------------------------------------27SE280, SE350 ------------------------------------------------------------------37SE450----------------------------------------------------------------------------47

VME L160 -----------------------------------------------------------------------------27L190B, L270B------------------------------------------------------------------37L320, L480 ---------------------------------------------------------------------57

1 adapter EX5854-21 3-3/4" 1" 4-1/2" 30° 12.91 adapter EX5849-21 3-3/4" 1-5/16" 9-1/8" 30° 14.4


T standard EX27SYL 8" 3-1/2" - - 9.4T tiger EX27VIP 7-3/4" 1/4" - - 8.4T twin tiger EX27TVIP 7-3/4" 3-3/4" - - 16.9T 6" flare EX27S6F 8-3/4" 6" - - 18.0T chisel EX27SD 8" 2" - - 10.53 adapter EX119-27 1-5/8" 5-13/16" 1-23/32" 1-5/16" 18.23 adapter EX119-27V 1-5/8" 5-13/16" 1-23/32" 1-5/16" 18.27 adapter EX360-27 2-1/2" 2-3/8" 3-7/8" 4-3/4" 17.05 adapter EX1550-27 4-5/8" 6" 3-7/8" - 28.85 adapter EX1551-27 4-5/8" 6" 3-7/8" - 29.11 adapter EX5827-27 2" 1-1/2" 9-7/8" 30° 27.11 adapter EX5850-27V 2" 1-9/16" 8-1/16" 30° 19.0


T standard EX37SYL 9-1/2" 4-3/4" - - 17.3T tiger EX37VIP 9-1/2" 1/4" - - 13.9T twin tiger EX37TVIP 9-1/2" 4-1/2" - - 16.7T 7' flare EX37S7F 11" 7" - - 25.7T 8' flare EX37S8F 11" 8" - - 27.0T chisel EX37SD 10-1/4" 2-1/4" - - 17.43 adapter EX129A-37 2-1/2" 8-19/32" 2-1/2" 1-3/4" 37.13 adapter EX129A-37V 2-1/2" 8-19/32" 2-1/2" 1-3/4" 37.17 adapter EX450-37 3-1/8" 3" 5" 5-3/4" 31.01 adapter EX5824-37 3" 2-1/16" 9-3/4" 30° 30.36 adapter EX1506-37 4-5/8" 6" 3-7/8" - 60.26 adapter EX1507-37 4-5/8" 6" 3-7/8" - 60.21 adapter EX5856-37V 4-7/8" 2-1/6" 9-3/4" 30° 37.9


T standard EX47SYL 11" 5" - - 24.8T tiger EX47VIP 11" 3/8" - - 22.7T twin tiger EX47TVIP 11" 5-1/8" - - 25.8T 9' flare EX47TVIP 12-5/8" 9" - - 34.7T chisel EX47SD 10-3/4" 2-1/2" - - 25.92 adapter EX1829A-47 - 2-9/16" 4-3/4" 30° 46.47 adapter EX450-47 3-1/8" 3" 5" 5-3/4" 37.01 adapter EX5857-47V - 2-5/8" 10-5/8" 30° 57.0

21 Series


T standard EX57SYL 13" 6" - - 34.0T tiger EX57VIP 13-1/8" 1/2" 34.0T twin EX57TVIP 13-1/8" 6-3/4" 40.82 adapter EX1856A-57V 3-3/16" 5-7/8" 11-3/4" 25° 71.0


New Generation of Esco Systems: Super V™

The Super V pin, tooth, and adapter system more closely matches break-outforces while reducing fuel consumption and machine maintenance.

Slimmer Profile; Matches Break-OutForces More Closely

Unique 1-Piece, Vertical Pin

The Super V tooth has a slimmer profile whichprovides increased penetration. The toothtwists a quarter turn onto the adapter and "buttsup" against the adapter nose to match break-out forces more closely.

The unique, 1-piece, vertical, drive-thru pin locks to the tooth ear for excellent point retention. It iscompletely covered by the tooth ear to reduce wear and avoid pin walk. The 1-piece pinprovides easier changeover and less cost; it is reusable for 29 Series sizes and larger.

Part Number ExplanationVarious information can be determined from the part numbering system. Refer to the followingchart for basic part number information.

Part Number Explanations for Exco Super V™Prefix Suffix ExplanationEV S_F Flare (_indicates width of flare.)EV SYL StandardEV TVY Twin TigerEV VY Tiger

Note: The numbersWithin the part numberrepresent the "Series."

Examples:EV19SYL 19 Series Standard ToothEV51TVY 51 Series Twin Tiger ToothEV43S9F 43 Series 9" Flare Tooth

Special tools for Super V AdaptersFor removal and installation of 29, 33, 39, 43 and 51 Series Super V teeth use special toolEXPRT

New Generation of Esco Systems: Super V™

Standard Teeth (SYL Suffix)(Centerline)• For general-purpose-to-heavy-duty digging

conditions.• Excellent penetration and wear.

Tiger Teeth (VY Suffix)(Non-Centerline)• High penetration for frost and tough

material.

Twin Tiger Teeth (TVY Suffix)(Non-Centerline)• For digging and loading in extremely tight

material.• Use as a corner tooth with tiger teeth in the

center.

Flare Teeth (S_F Suffix)(Centerline)• For digging in mud-like conditions• Provides more bucket capacity by bridging

material between teeth.

Esco Super V™ Systems Retainers

Illustrated partsare actual size.

EV19PN19 Series

EV23PN23 Series

EV29PN29 Series EV33PN

33 Series

EV39PN39 Series

EV43PN43 Series

EV51PN51 Series

Esco Super V™ System - Tooth by Series


a standard EV19SYL üb tiger EV19VY üc twin tiger EV19TVY üd flare EV19TF ü- pin EV19PN ü- adapter EV5854-V19 ü


a standard EV23SYL üb tiger EV23VY üc twin tiger EV23TVY üd flare EV23S5F ü- pin EV23PN ü- adapter EV5849-V23 ü



JD: 190E, 290D Competitive: Case: 488C, 590SL Caterpillar: 438B Komatsu: PC95, PC100-5 Liebherr: R310B, O&K: MH2.10

JD: 490, 490D, 490E, 495D, 590D, 595, 595D Competitive: Case: 688C: Caterpillar: 205B, 211B, E110B, E120B Kobelco: SK100, SK120, SL150 Komatsu: PC120-6, PC150LC5 Liebherr: R900Lit; Link-Belt: 2650, 2700

JD: 690, 690A, 690B, 690C, 690D, 690E, Competitive: Case: 883C, 9030, Caterpillar: 215D, 320L, E200B, Kobelco: SK200, Komatsu: PC180LC5, PC200LC6, Liebherr: R902Lit, R912Lit, O&K: RH CITY, RH5








a standard EV51SYL üb tiger EV51VY üc twin tiger EV51TVY ü- pin EV51PN ü- adapter EV5857A-V51 ü

JD: 892D, 892E, Competitive: Case: 1288C, 9050, Caterpillar: 235B, 235C, 330L, Kobelco: SK300, Komatsu PC300LC5, PC360LC3, Liebherr: R942Lit, Link-Belt: 4300, O&K: RH12

JD: 922D, 992E, Competitive: Case: 9060, Caterpillar: 235D, 350L, Kobelco: SK400, Komatsu: PC400LC5, Liebherr: R954Lit, Link-Belt: 5800, O&K: RH16, RH20

JD: 922D, 992E, Competitive: Caterpillar: 245D, Komatsu: PC650LC3, Liebherr: R964Lit, O&K: RH25

JD: 790, 790D, 790E, 792, 792D, Competitive: Case: 1088C, 1188C, 9040, Caterpillar: 225D, 325L, E240B, E300B, Kobelco: SK220, Komatsu PC220LC6, Liebherr: R922Lit, R923Lit, Link-Belt:: 3400, O&K: RH6-20

Esco Super V™ System - Specifications

T

style description part no. a b c d nose angle lbs.

T standard EV19SYL 6-1/2" 2-1/2" - - - 5.2T tiger EV19VY 7" 7/16" - - - 4.3T twin tiger EV19TVY 7" 3" - - - 5.5T flare EV19TF 6-1/2" 4-1/2" - - - 61 adapter EV5854-V19 1" 3-1/8" 6-1/2" 30° 12° 8.7


T standard EV23SYL 7-1/2" 3" - - - 6.8

T tiger EV23VY 8" 1/2" - - - 6.5T twin tiger EV23TVY 8" 3-1/2" - - - 7.5T flare EV23S5F 7-1/2" 5" - - - 8.81 adapter EV5849-V23 1-1/8" 3-3/4" 7-1/2" 30° 12° 14.5


T standard EV29SYL 8-5/16" 3-1/2" - - - 10.7

T tiger EV29VY 9-9/16" 7/16" - - - 8.7T twin tiger EV29TVY 9-9/16" 4-1/8" - - - 9.6T flare EV29S6F 9-1/6" 6" - - - 13.71 adapter EV5850-V29 1-1/2" 4-1/2" 8-1/4" 30° 10° 17.5

19 Series

23 Series

29 Series


T standard EV33SYL 9-1/8" 4" - - - 15T tiger EV33VY 10-3/8" 1/2" - - - 12.3T twin tiger EV33TVY 10-3/8" 4-9/16" - - - 14.2

T flare EV33S7F 10" 7" - - - 19.6

1 adapter EV5855-V33 1-1'2" 5" 9-1/4" 30° 10° 25


T standard EV39SYL 10-1/8" 4-3/4" - - - 21.5

T tiger EV39VY 11-11/16" 9/16" - - - 17.5

T twin tiger EV39TVY 11-11/16" 5-1/8" - - - 19.9

T flare EV39S8F 11" 8" - - - 23.3

1 adapter EV5856-V39 2" 5-3/4" 10-3/8" 30° 10° 36


T standard EV43SYL 11-1/4" 5" - - - 29

T tiger EV43VY 12-7/8" 5/8" - - - 23.5T twin tiger EV43TVY 12-7/8" 5-5/8" - - - 27.4T flare EV43S9F 12-5/16" 9" - - - 38.51 adapter EV5856-V43 2" 6" 11" 30° 10° 48


T standard EV51SYL 12-1/8" 5-1/2" - - - 33

T tiger EV51VY 14" 3/4" - - - 30T twin tiger EV51TVY 14" 6-1/4" - - - 361 adapter EV5857A-V51 2-1/2" 6-7/16" 11-7/8" 30° 10° 63

39 Series

43 Series

51 Series

Esco Super V™ System - Specifications33 Series

CE98- 01U,02C Date

John Deere Replacement Teeth for Hensley ProductsJohn Deere replacement teeth for Hensley products come in sizes and tooth designs to fit almost allmachine makes and models.The Parabolic (Dished-Out) Design Creates a Wedging, Self-Tightening FitWith use, the parabolic (dished-out) designmating system creates a wedging and self-tightening fit. A dished-out area in the lowertop and bottom of the adapter nose plus arecessed channel on the inside sidewall of thetooth which matches a tapered extension on theadapter nose piece forms a locking fit in alldirections and reduces tooth movement bothvertically and horizontally. The tooth andadapter are designed as a bucket tooth systemthat will absorb impact loads and generallyreduce the amount of abrasive action to thebucket lip.Flex Pin RetentionThe TP400HD and TP475HD Flex Pins aremade of two hardened steel forgings withvulcanized neoprene between them. Onceinstalled, the flex pin provides a four-waylocking support.Removal is easy as pins can be driven throughthe bottom of the adapter.Hensley Series 350, 400 and 475 teeth use avertically-mounted flex pin.Roll Pin Retention and InstallationThe smaller series of John Deere replacementteeth for Hensley products are retained with aroll pin. The vertical design allows easyremoval and installation of center teeth. It is asimple, economical, reliable means to retainthe tooth to the adapter.These steel roll pins should always be installedwith the split facing towards the front of thetooth.Series 156, 160, 220, and 310 use a roll pin.Steel KeyA steel key retains the 290, 330, 370 and 410Series of John Deere replacement teeth forHensley products. This key providesoutstanding retention in all types ofapplications. It is not reuseable.

Part Number Explanation

Hensley2

Fanggs Digging Teeth (TF__) (Non-Centerline)• For general-purpose-to-heavy

digging.• Provides a clean start and close

crowd.

Standard Teeth(TX__) (Centerline)• For general-purpose to heavy-

duty applications.• Provides long wear life.

Tiger Teeth (TT__) (Non-Centerline)• For digging and loading in

severe conditions - frost,hardpan, extremely tight soil.

• Excellent penetration.

Twin Tiger Teeth (TW__WT) (Non-Centerline)• For digging and loading in

extremely tight material.• Use as a corner tooth with tiger

teeth in center positions.

Abrasion Paneled Teeth(TX__AP) (Centerline)• For loading and digging in

highly-abrasive material.• Panel design makes tooth self-

sharpening.

Flare Teeth (TX__F) (Centerline)• For digging in loose and mud-

like conditions to improve thebridging of material betweenteeth.

• Provides flush cut or clean-up.

Part Number Explanation (Replacement Teeth for Hensley Products)Prefix Suffix ExplanationTF Fanggs DiggingTT TigerTX StandardTX AP Abrasion PaneledTX F FlareTX WT Twin Tiger

Example:Part Number TX400 Series 400 standard tooth.Part Number TX400AP Series 400 abrasion paneled tooth.

NOTE: The numbers within the partnumber represent the “Series.”

Various information can be determined from the part number system. Refer to the following chart forbasic part numbering information.

John Deere Replacement Teeth for Hensley Products - Types Available


Hensley - Teeth by Series

156 Series (Top Mount)style description part no. rcv. disc. non stock used on

e Fanggs TF156 STKf standard TX156 STKc tiger TT156 STKd twin tiger TX156WT STK- tooth, star PMS156 STK- heavy-duty PMS156HD STK- tiger h-d PMT156HD STKb flare PMX156F STK- heavy PMX156H STK- extra long PMX156LP STK- tooth, long PMX156L STKd tooth, twin tiger long PMX156WTL STK- pin TF13P STK- pin TP156 STK- adapter T834X156 STK- adpt., ctr. (156 nose) PM110HX STK- adpt., RH (156 nose) PM110RH STK- adpt., LH (156 nose) PM110LH STK- blade (156 nose) PM11V16L STK- blade (156 nose) PM11V16R STK- adpt., W-O, 1-1/2 leg, .625" lip 30 degrees PM230X156 STK- adpt., B-O, .81" thr., 29deg JCB 3C PM300X156 N.S.- adpt., B-O, LH, crnr., refer to 300X156 PM301X156 N.S.- adpt., B-O, RH, crnr. refer to 300X156 PM302X156 N.S.- adpt., B-O, Deere no. U-41344 PM344X156 N.S.- adpt., B-O, 1-1/2 leg, .93" throat PM350X156 N.S.- adpt., B-O, 2 leg, step, Case #D35642 PM401X156 N.S.- adpt., W-O, 1-1/2 leg, .625" lip PM548X156 N.S.- adpt., W-O, 1-1/2 leg, .875" lip PM549X156 STK- adpt., W-O, 1-1/2 leg, 1" lip PM550X156 STK- adpt., B-O, .625" throat, 21deg PM551X156 N.S.- adpt., W-O, 1-1/2 leg, .75"" lip PM552X156 STK- adpt., W-O, flush, .75"" to .875" PM681X156 STK- adpt., B-O, step (Drott TD-6) PM682X156 N.S.- adpt., B-O, 2 leg, 1.18" throat PM683X156 N.S.- adpt., B-O, 2 leg, .81" throat PM684X156 N.S.- adpt., W-O, bttm. leg, 1" lip PM805X156 STK- adpt., W-O, bttm. leg, .625" to .875", ditch wit PM835X156 STK- adpt., W-O, bttm. leg, .75"" to 1.0" lip PM836X156 STK- 12" lip blade w/3 noses PM12M156-12A STK- 14" lip blade w/3 noses PM14M156-12A STK- 18" lip blade w/4 noses PM18M156-12A STK- 24" lip blade w/5 noses PM24M156-12A STK- ripper box PMB922B STK- box pin (B922B) PMP922 STK- pin removal tool for P100, P156 PMPRT156 STK- pin punch PM516PU STK- adapter, nose, W-O PM156WN STK

JD: 300, 310D, 315D, 410D, 500B, 510, 510D, 710B, Competitive: backhoes

Hensley - Teeth by Series160 Series (Top Mount)style description part no. rcv. disc. non stock used on

e Fanggs TF160 STKf standard TX160 STKc tiger TT160 STKd twin tiger TX160WT STKb flare TX160F STK- star PMS160 N.S- heavy-duty PMX160HD STK- pin TP160 STK- adapter T658X160 STK JD: 80, 110, 190E, 290D, Competitive: backhoes, excavators- adapter PM552X160 N.S- adapter PM850X160 N.S- adpt., B-O, 2 leg, .81" throat, (TCM 830) PM168X160 N.S- adpt., B-O, RH, crnr. PM169X160 N.S- adpt., B-O, LH, crnr. PM170X160 N.S- adpt., B-O, 2 leg 1.125" throat PM204X160 N.S- adpt., B-O, 2 leg, Cat #8J2930 PM309X160 N.S- adpt., B-O, 2 leg, Komatsu #1 13-70-22140 PM310X160 N.S- adpt., B-O, 1-1/2 leg, 1.31" throat (Clark 55C) PM314X160 N.S- adpt., B-O, 2 leg, .93" throat PM504X160 N.S- adpt., B-O, step PM510X160 N.S- adpt., B-O, step PM553X160 N.S- adpt., B-O, 2 leg, .90" throat, (KSS-65Z) PM650X160 STK- adpt., B-O, RH, crnr., refer to 650X160 PM653X160 N.S- adpt., B-O, LH, crnr., refer to 650X161 PM654X160 N.S- adpt., B-O, step PM702X160 N.S- adpt., B-O, 2 leg, 1.31" throat PM706X160 N.S- adpt., B-O, 2 leg, 1.18" throat PM717X160 N.S- adpt., B-O, 2 leg, 1.06" throat PM718X160 N.S- adpt., B-O, 2 leg, 1.06" throat PM750X160 N.S- adpt., B-O, H&L #L2145-23, L-4013-23 PM775X160 N.S- adpt., B-O, Case/Drott 4-in.-1, #26269 PM787X160 N.S- adpt., B-O, Case/Drott 4-in.-1, #229291 PM792X160 N.S- adpt., W-O, top leg, H&L #809-24 PM809X160 N.S- adpt., B-O, step PM840X160 N.S- adpt., B-O, 1.18" throat, Deere U41344 PM861X160 N.S- adpt., B-O, 2 leg, 1.31" throat PM927X160 N.S- adpt., W-O, bttm. Leg PM928X160 N.S- ripper box PMB926A STK- box pin (B926A) PMP926 STK- pin punch PM716PU STK- adpt. nose, W-O PM160WN STK

162 Series (Side Mount)style description part no. rcv. disc. non stock used on

c tooth, tiger PMT162 STKf standard PMX162 STKb flare, 4" PMX162F STK- heavy duty PMX162HD STKd twin tiger PMX162WT N.S- pin TP160 STK- flex pin PMP162 STK- adpt., B-O, 1.31" throat, 30 deg, Clark 55C PM314X162 N.S- adpt., B-O, step PM510X162 N.S- adpt., B-O, step PM702X162 N.S- adpt., B-O, 2 leg, 1.06" throat PM750X162 N.S- adpt., W-O, bttm. leg, 1" to 1.25" PM850X162 N.S- adpt., B-O, 1.06" throat, (VME L-70) PM901X162 N.S- adpt., B-O, 1.25" throat, (VME L-90) PM902X162 N.S- adpt., B-O, LH, refer to 902X162 PM903X162 N.S- adpt., B-O, RH, refer to 902X163 PM904X162 N.S- adpt., B-O, 2 leg, 1.31" throat PM927X162 N.S- blade (162 nose) - RH PM13V16R N.S- blade (162 nose) - LH PM13V16L N.S- adpt. nose, W-O PM162WN STK

Hensley - Teeth by Series


e Fanggs TF220 STKf standard TX220 STKc tiger TT220 STKd twin tiger TX220WT STKb flare TX220F STKa abrasion paneled TX220AP STK- star PMS220 N.Sa abrasion PMX220ABR STK

down pitch PMX220DP STK- twin tiger long PMX220WTL STK- tooth, tiger long PMT220L STK- pin TP160 STK- adapter T109X220 STK- adpt., B-O, 2 leg, 1.875" throat PM0C1X220 N.S- adpt., B-O, 2 leg, 1.625" throat PM3C1X220 N.S- adpt., W-O, 1-1/2 leg, 1" lip PM103X220 STK- adpt., W-O, notched LH crnr. PM107X220 STK- adpt., W-O, notched RH crnr. PM108X220 STK- adpt., B-O, 1.125" throat, (D57S) PM111X220 N.S- adpt., B-O, crnr., RH, 1.15 thr PM112X220 STK- adpt., B-O, crnr., LH, 1.15 thr PM113X220 STK- adpt., B-O, 2 leg, .96" throat PM155X220 N.S- adpt., B-O, 2 leg, 1" throat PM168X220 N.S- adpt., B-O, RH, crnr. PM169X220 N.S- adpt., B-O, LH, crnr. PM170X220 N.S- adpt., B-O, step, IH #610986C1 PM211X220 N.S- adpt., B-O, ctr. (920, 930, 941B)(1U0257) PM257X220 N.S- adpt., B-O, crnr., Cat #3G4258 PM258X220 N.S- adpt., B-O, crnr., Cat #3G4259 PM259X220 N.S- adpt., B-O, step, IH #611606C1(270, 442, 444)PM270X220 N.S- adpt., B-O, 2 leg, 1.31" throat PM295X220 N.S- adpt., B-O, 2 leg, 1.06" throat PM310X220 N.S- adpt., B-O, 1.18" thr, 30deg (Case 750, 850) PM311X220 N.S- adpt., B-O, 2 leg 1"" throat, 25deg, Kom D41 PM410X220 N.S- adpt., B-O, 1.31" thr, ESCO #4738-25 (W36) PM473X220 N.S- adpt., B-O, 2 leg, 1.31" throat PM500X220 N.S- adpt., B-O, step, Cat #7J4415 PM613X220 N.S- adpt., stake-type (Poclain, PC8) PM615X220 N.S- adpt., B-O, ctr. 1.06" throat (Case 621, 855D) PM621X220 STK- adpt., B-O, crnr. (Case 621) PM622X220 STK- adpt., B-O, 2 leg, 1.03" throat PM700X220 N.S- adpt., B-O, RH, refer to 700X22 PM701X220 N.S- adpt., B-O, LH, refer to 700X22 PM702X220 N.S- adpt., B-O, step (Wabco 222G) PM703X220 N.S- adpt., B-O, step (Fiat-Allis 161) PM706X220 N.S- adpt., B-O, step (Wabco 222G) PM707X220 N.S- adpt., B-O, step PM710X220 N.S- adpt., B-O, 1.18" throat, (F-A 545B) PM730X220 N.S- adpt., B-O, 1.09" throat, Case #D49545 PM747X220 N.S- adpt., B-O step PM785X220 N.S- adpt., B-O step PM786X220 N.S- adpt., B-O, 1-1/2 leg, 1.06" throat PM796X220 N.S- adpt., B-O, 1-1/2 leg, .875" throat PM797X220 N.S- adpt., W-O, 1-1/4 leg, 1.5" throat PM809X220 N.S- adpt., B-O, 2 leg, 1.31" throat PM810X220 N.S- adpt., B-O, 2 leg, 1" throat PM811X220 N.S- adpt., B-O, 2 leg, 1.25" throat PM812X220 N.S- adpt., B-O, 1.06" throat, (Case W18) PM818X220 N.S- adpt., B-O, 1.31" throat PM824X220 N.S- adpt., W-O, bttm. leg, 2" to 2.25" PM855X220 N.S- adpt., B-O, 2 leg, 1.375" throat PM856X220 N.S- adpt., B-O, 1.68" throat PM857X220 N.S- adpt., B-O, step, Deere #T38783 PM860X220 N.S- adpt., B-O, 2 leg, 1.31" throat PM927X220 N.S- adpt. nose, W-O PM220WN STK

Hensley - Teeth by Series225 Series style description part no. rcv. disc. non stock used on

c tiger PMT225 STKf std. PMX225 STKa abr. paneled PMX225AP N.Sa abr. PMX225ABR N.Sb flare, 4.5"" PMX225F N.S- twin tiger PMX225WT N.S- flex pin PMP225 STK- adpt., B-O, 2 leg, 1.875" throat PM0C1X225 N.S- adpt., W-O, bttm. leg, 2" lip PM102X225 N.S- adpt., W-O, 1-1/2 leg, 1" lip PM106X225 N.S- adpt., B-O, 1.125" throat PM111X225 N.S- adpt., B-O, 2 leg, .96" throat PM155X225 N.S- adpt., B-O, rev., crnr., Deere #112163 PM163X225 N.S- adpt., B-O, ctr., .81" throat PM164X225 N.S- adpt., B-O, ctr., 1.06" throat PM165X225 STK- adpt., B-O, crnr. (544E, 624E) PM191X225 N.S- adpt., B-O, 2 leg, 1.06" throat PM257X225 N.S- adpt., B-O, LH, crnr., Cat #3G4258 PM258X225 N.S- adpt., B-O, RH, crnr., Cat #3G4259 PM259X225 N.S- adpt., B-O, 2 leg, 1.06" throat PM310X225 N.S- adpt., B-O, 1.43" thr, 22deg, Clark #251 147 PM313X225 N.S- adpt., B-O, 1.56" thr, 33deg, Deere T35385 PM385X225 N.S- adpt., B-O, 1.31" throat, 22deg (Case W36) PM473X225 N.S- adpt., B-O, 1.31" throat, Deere T29886 PM544X225 N.S- adpt., B-O, step PM785X225 N.S- adpt., B-O, LH, crnr. PM572X225 N.S- adpt., B-O, 1.06" throat PM611X225 N.S- adpt., B-O, step (Wabco 222G) PM703X225 N.S- adpt., B-O, 1.09" throat PM747X225 N.S- adpt., B-O, 1-1/2 leg, 1.06" throat PM796X225 N.S- adpt., B-O, 1-1/2 leg, .875" throat PM797X225 N.S- adpt., B-O, 2 leg, 1.31" throat PM810X225 N.S- adpt., B-O, 2 leg, 1" throat PM811X225 N.S- adpt., B-O, 1.06" throat PM818X225 N.S- adpt., B-O, 1.31", Case #L58824 PM824X225 N.S- adpt., W-O, bttm. leg, 2" to 2.25" lip PM855X225 N.S- adpt., B-O, 1.68" throat PM857X225 N.S- adpt., B-O, step, Deere #T38783 PM860X225 N.S- adpt., W-O, flush, 1.25" lip, 2" PM900X225 N.S- adpt., B-O, ctr., 1.43" throat PM902X225 N.S- adpt., B-O, LH, crnr., refer to 902X225 PM903X225 N.S- adpt., B-O, RH, crnr., refer to 902X225 PM904X225 N.S- adpt., nose, W-O PM225WN STK


e Fanggs TF290 STKf standard TX290 STKc tiger TT290 STKd twin tiger TX290WT STKb flare TX290F STKa abrasion panel TX290AP STKa abrasion PMX290ABR STK

pin TK290 STKflex pin PMP290 STKadapter T127X290 STKadapter T158X290 STKadapter PM125X290 N.Sadapter PM150X290 N.Sadapter PM190X290 STKadapter PM191X290 STKadapter PM673X290 N.Sadapter PM674X290 N.Sadapter PM822X290 N.Snose template kit for 290, 330 PMA-TEM STKnose rebuild kit for 290 series PMA290NR STKflex pin, C-19 lips (136X290) PMP136 STKflex pin, solid rubber PMP290STP STKpin removal tool for (290, 330) PMPRT290 STKtooth, sharp, ribbed PMX290SYL STKadpt., stake type, ESCO C-19 lip PM119X290 N.Sadpt., W-O, 1-1/2 leg, 2" lip PM124X290 N.Sadpt., W-O, 1-1/2 leg, RH, 1.75" PM130X290 N.Sadpt., W-O, 1-1/2 leg, LH, 1.75" PM131X290 N.Sadpt., stake type, Hensley C-19 PM136X290 STKadpt., B-O, 2 leg, 1.25" thr. PM156X290 N.Sadpt., B-O LH crnr. (955L) PM308X290 N.Sadpt., B-O RH crnr. (955L) PM309X290 N.Sadpt., W-O, bttm. leg, 1.25" to 1.5" lip PM383X290 N.Sadpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) PM430X290 N.Sadpt., B-O, 2 leg, 1.93" thr. 23deg, (85Z11) PM480X290 STKadpt., B-O, LH (85Zll), (req. 486INS) PM486X290 STKadpt., B-O, RH (85Zll), (req. 486INS) PM487X290 STKadpt., B-O, LH (80Zlll) PM488X290 N.Sadpt., B-O, RH (80Zlll) PM489X290 N.Sadpt., B-O, 2 leg, 1.03" thr. (80ZIII) PM490X290 N.Sadpt., W-O, 1-1/2 leg, 1.375" lip PM580X290 N.Sadpt., stake type (Akerman H9, H11) PM589X290 N.Sadpt., B-O, ctr., 1.375" thr. PM721X290 STKadpt., B-O, crnr. (Case 721) PM722X290 STKadpt., B-O, crnr. (Case 821) PM820X290 STKadpt., B-O, ctr., 1.31" thr. (Case 821) PM821X290 N.Sadpt., B-O, Crnr (VME L-140) PM904X290 N.Sadpt., B-O, 2 leg, 1.56" thr. PM905X290 N.Sadpt. nose, W-O PM290WN STK


f standard PM295 STKc tiger PMT295 STKd twin tiger PM295WT STKa abrasion panel PM295AP STK- tooth, short, ribbed PM295SYL STKb flare PM295F STK steel pin PMP295 STK pin, steel spring PMP295SL STK

adpt. 1-1/4" lip PM127X295 STKadpt., C-19 cast lip PM136X295 STKadpt. 1-1/2" lip PM158X295 STKadpt. B-O L.H. PM308X295 N.Sadpt., B-O R.H. PM309X295 N.Sadpt. bttm. leg W-O PM383X295 N.Sadpt., B-O PM430X295 N.Sadpt., stake type, Akerman H7 PM589X295 STKpin removal tool for P295SL PMP295SLRT STKadpt., W-O nose PM295WN STK

JD: 490, 490D, 490E, 495D, 590D, 595, 595D, 120, 160LC, Competitive: excavators

Hensley - Teeth by Series300 Series (Side Mount)style description part no. rcv. disc. non stock used on

c tiger PMT300 STKf standard PMX300 STKa abrasion PMX300ABR N.Sa abrasion panel PMX300AP N.Sb flare, 6"" PMX300F N.S- heavy duty rock PMX300R N.Sd twin tiger PMX300WT N.S flex pin (4 tab) PMP300B STK adpt. nose, W-O PM300WN STK


e Fanggs TF310 STKpin TP160L STK

f standard TX310 STKc tiger TT310 STKd twin tiger TX310WT STKb flare TX310F STK- tooth, 4" wide PMX310-4 STKa abrasion paneled TX310AP STKa abrasion PM310ABR STK

pin TP160 STKflex pin, C-19 lip (136X310) PMP136 STKadapter T153X310 STKkey PMK668 STKrefer also to PM142X330 PM110X310 N.Sadpt., stake-type, ESCO C-19 lip PM119X310 N.Sadpt., W-O, bttm. leg, 1.5" lip PM122X310 N.Sadpt., W-O, 1-1/2 leg, 2" lip PM124X310 N.Sadpt., W-O, flush, 1.25" lip PM125X310 N.Sadpt., W-O, 1-1/2 leg, 1.25" lip PM127X310 N.Sadpt., W-O, 1-1/2 leg, 1.25" lip PM128X310 N.Sadpt., W-O, RH, 1-1/2 leg, 1.75" PM130X310 N.Sadpt., stake-type, C-19 lip (reqs P136) PM136X310 STKadpt., B-O, 1-1/2 leg, 1.43" throat PM138X310 N.Sadpt., flush, 1.5" str. lip PM150X310 N.Sadpt., RH, flush, 1.5" sp. lip PM151X310 N.Sadpt., LH flush, 1.5" sp. lip PM152X310 N.Sadpt., W-O, RH, 1-1/2 leg, 1.5" lip PM154X310 N.Sadpt., W-O, LH, 1-1/2 leg, 1.5" lip PM155X310 N.Sadpt., B-O, 2 leg, 1.25" thr. PM156X310 N.Sadpt., W-O, 1-1/2 leg, 1.5" lip PM158X310 STKadpt., W-O, LH, notched crnr. PM159X310 STKadpt., W-O, RH, notched crnr. PM160X310 STKadpt., B-O, 2 leg, 1.43" thr. PM168X310 N.Sadpt., B-O, RH, crnr. PM169X310 N.Sadpt., B-O, LH, crnr. PM170X310 N.Sadpt., B-O, 1.46" thr. Komatsu D65, D75 PM181X310 N.Sadpt., B-O, 2 leg, 1.31" thr. PM185X310 N.Sadpt., B-O, 2 leg, 1.81" throat PM301X310 N.Sadpt., B-O, LH crnr. (955L) PM308X310 N.Sadpt., B-O, RH crnr. (955L) PM309X310 N.Sadpt., B-O, 1.31" thr., 22deg, Case 1450 PM317X310 N.Sadpt., B-O, specialty item PM323X310 STKadpt., W-O, bttm. leg, 1.25" to 1.5" lip PM383X310 N.Sadpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) PM430X310 N.Sadpt., W-O, 1-1/2 leg, 1" lip PM494X310 N.Sadpt., B-O, step PM495X310 N.Sadpt., B-O, 2 leg, 1.81" thr, Furukawa 320A PM550X310 N.Sadpt., W-O, 1-1/2 leg, 1.375" lip PM580X310 N.Sadpt., stake-type (req. K668) PM668X310 N.Sadpt., B-O, 1-1/2 leg, 1.375" thr PM742X310 N.Sadpt., B-O, step PM756X310 N.Sadpt., B-O, step PM758X310 N.Sadpt., B-O, step PM759X310 N.Sadpt., B-O PM812X310 N.Sadpt., W-O, bttm. leg, 1.5" lip PM822X310 STKadpt., W-O, bttm. leg, .75" to .875" Lip PM844X310 N.Sadpt., W-O, 1.375" special lip PM845X310 N.Sadpt., B-O, 2 leg, 1.81" thr. (HD 6G, 12G) PM859X310 N.Sadpt., W-O, flush, 1.5" str. lip PM900X310 N.Sadpt., W-O, flush, LH, sp. lip PM901X310 N.Sadpt., W-O, flush, RH, sp. lip PM902X310 N.Sadpt. nose, W-O PM310WN STK

JD: 160LC, 200LC, 230LC, 270LC, 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, Competitive: excavators, loaders


e Fanggs TF330 STKf standard TX330 STKc tiger TT330 STKd twin tiger TX330WT STKb flare TX330F STKa abrasion panel TX330AP STK- sharp, ribbed PMX330SYL STK- short rock PMX330SR N.Sa abrasion PMX330ABR STK

pin TK330 STK flex pin PMP330 STK

adapter T158X330 STKadapter PM190X330 N.Sadapter PM743X330 N.Sadapter PM744X330 N.Sadapter PM822X330 N.Sadapter PM937X330 STKnose rebuild kit for 330 Series PMA330NR STKlip fastener, C-19 lips (136X330, 136X310) PMP136 STKlip fastener, C-29 lips (236X330) PMP236 STKsteel wedge PMW330 STKadpt., stake-type, Hensley C-19 PM136X330 STKadpt., W-O, LH, notched crnr. PM159X330 STKadpt., W-O, RH, notched crnr. PM160X330 STKadpt., W-O, 1-1/2 leg, 1.625" lip PM225X330 N.Sadpt., stake-type, Hensley C-29 PM236X330 N.Sadpt., B-O specialty item (Sauerman) PM323X330 STKadpt., W-O, bttm. leg, 1.25"lip, 23deg PM383X330 N.Sadpt., B-O, ctr. (VME L150, L180) PM901X330 N.Sadpt., B-O, ctr. (Case 921) PM921X330 N.Sadpt., W-O, LH, notched crnr. PM935X330 STKadpt., W-O, RH, notched crnr. PM936X330 STKadpt. nose, W-O PM330WN STK

JD: 160LC, 200LC, 230LC, 270LC, 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, Competitive: excavators


f standard PM335 STKa abrasion panel PM335AP STKb flare PM335F STK- short, ribbed PM335SYL STKc tiger tooth PMT335 STKd twin tiger tooth PM335WT STK steel pin PMP335 STK pin, steel spring PMP335SL STK

adpt., 1.5" lip PM158X335 STKadpt., W-O, flush 1.625" - 1.75" lip, 30 deg PM190X335 STKadpt., C-29 Hensley cast lip PM236X335 STKadpt., stake (Akerman H12, 14, 16) PM355X335 STKadpt., L.H. crnr., 1.75" lip PM935X335 STKadpt., R.H. crnr. 1.75" lip PM936X335 STKadpt., 1.75" lip PM937X335 STK

pin removal tool for P335SL PMP335SLRT STKadpt., W-O nose PM335WN STK


f standard TX350 STKc tiger PMT350 STKa abr. paneled, short PMX350APS N.Sb flare PMX350F N.S Competitive: excavatorsd twin tiger PMX350WT STK

pin TP400HD STKadpt. nose, W-O PM350WN STK


e Fanggs TF370 STKf standard TX370 STKc tiger TT370 STKd twin tiger TX370WT STKa abrasion paneled PMX370AP STKb flare PMX370F STK- sharp, ribbed PM X370SYL STKa abrasion PMX370ABR STK steel keeper TK370 STK

flex pin, front lock PMP370FL STKpin removal tool for (370, 410, 450) PMPRT370 STKfastener for Hensley C-29 lips PMP236 STKadpt., stake-type, ESCO C-29 lip PM129X370 N.Sadpt., W-O, 1.5" lip PM158X370 N.Sadpt., stake-type, Hensley C-29 PM236X370 N.Sadpt., W-O, bttm. leg, 2" to 2.25" lip PM827X370 N.Sadpt. W-O, ctr., 2" lip T940X370 STK JD: 230LC, 270LC, 330LC, 370adpt., W-O, RH/LH, 1.75" sp. lip PM936X370 N.Sadpt., W-O, ctr., 1.75" str. lip PM937X370 STKadpt., W-O, LH, 2" flush sp. lip PM947X370 STKadpt., W-O, RH, 2" flush, sp. lip PM948X370 STKadpt., W-O, ctr., 2" flush, str. lip PM949X370 STKadpt. nose rebuild kit for 370 Series PMA370NR STKadpt. nose, W-O PM370WN STK


e standard PM385 STKb flare PM385F STK- sharp, ribbed PM385SYL STKc tiger PMT385 STKd twin tiger PM385WT STK pin, steel PMP385 STK

pin, steel spring PMP385SL STKadpt., stake type, Hensley C29 PM236X385 STKadpt., stake (Akerman H12, 14, 16) PM355X385 STKadpt., W-O, bttm. leg PM827X385 STKadpt., W-O, 1-1/2 leg, 1.75" lip PM937X385 STKadpt., W-O, 1-1/2 leg, 2" lip PM940X385 STKadpt., W-O, flush, 2" lip PM949X385 STK

pin removal tool for P385SL PMP385LRT STKadpt., W-O nose PM385WN STK


e Fanggs TF400 STKf standard TX400 STKc tiger TT400 STKd twin tiger TX400WT STKb flare TX400F STKa abrasion paneled TX400AP STKa abrasion PMX400ABR STKa abrasion heavy PMX400ABRB STK

short PMX400H STKlong sharp PMX400LS STKpenetrator narrow PMX400SD STKpin TP400HD STKslag pin TP400SA STKslag pin TP400SB-S STKslag pin PMP400SB-OS STKwedge key PMK129C STKadapter T802X400 STKadapter PM800X400 N.Sadpt., stake-type, ESCO C-29 lip PM129X400 N.Sadpt., stake-type, for Hensley PM236X400 STKadpt., W-O, 1-1/2 leg, 1.5" lip PM604X400 STKadpt., W-O, bttm. leg, 2" to 2.25" PM827X400 N.Sadpt., W-O, 2 leg, ctr., 2" lip PM830X400 N.Sadpt., W-O, notched crnr., LH PM831X400 N.Sadpt., W-O, notched crnr., RH PM832X400 N.Sadpt., W-O, 1-1/2 leg, 2" lip PM938X400 STKadpt., W-O, 1-1/2 leg, 2" lip PM940X400 N.Sadpt., B-O, 2 leg, 1.75" thr. PM945X400 N.Snose rebuild kit for 410 Series PMA410NR STKadpt. nose, W-O PM400WN STK


e Fanggs TF410 STKf standard TX410 STKd twin tiger TX410WT STKc tiger TT410 STKa abrasion PMX410ABR STKa abrasion paneled PMX410AP STKb flare PMX410F STK

long, sharp PMX410LS STKsharp, ribbed PMX410SYL STK

steel keeper TK410 STKadpt. W-O, 1-1/2 leg, 2" lip T940X410 STK JD: 230LC, 270LC, 330LC, 370, 450LCadpt., stake type Hensley C-29 PM236X410 N.Sadpt., W-O, 2 leg, 2" str. lip PMA464X410 N.Sadpt., W-O, 2 leg, 2" sp. lip PMA465X410 N.Sadpt., W-O, 2 leg, 2" sp. lip PMA466X410 N.Sadapt., W-O bttm. leg PM827X410 N.Sadpt., W-O 1-1/2 leg 2" lip PM890X410 N.Sadpt., W-O 1-1/2 leg 1.75" lip PM937X410 N.Sadpt. nose, W-O PM410WN STK


c tiger PMT450 STKf standard PMX450 STKa flare PMX450F N.S

abrasion PMX450ABR STKabrasion paneled PMX450AP STK

d twin tiger PMX450WT STKadpt. nose, W-O PM450WN STK


a Fanggs TF475 STKf standard TX475 STKc tiger TT475 STKd twin tiger TX475WT STKb flare TX475F STKa abrasion paneled TX475AP STKa abrasion PMX475ABR N.S

slag heavy PMX475AH N.Sslag long PMX475AHL N.Sslag h-bottom PMX475AHS STK

JD: 200LC, 230LC, 270LC, 330LC, 370, 450LC, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 890, 890A, 892D, 892E, 992D, 992E, Competitive: excavators, loaders

Hensley - Teeth by Serieslong heavy PMX475LP N.Sslag PMX475S STKtiger long PMT475L STKtwin tiger long PMX475WTL STKpin TP475HD STKadapter T303X475 STKadapter PM988X475 STKadpt. nose, W-O PM475WN STK


f standard TX500 STKabrasion panel TX500AP STKribbed sharp TX500SYL STKtiger TT500twin tiger TX500WTsteel key pin TK500R STKadapter T806X500 STK JD: 550LC, 600CLC, 750, 800C


ribbed sharp TX550SYL STKtiger TT550twin tiger TX550WTsteel key pin TK550R STKadapter T806X550 STK JD: 600CLC, 750, 800C

JD: 270LC, 330LC, 450LC, 890, 890A, 892D, 892E, 992D, 922E, Competitive: excavators, loaders

Hensley - Teeth by SeriesSidecuttersstyle description part no. rcv. disc. non stock used on

strikeoff sidecutter, 3/1 pattern PMSCB220-SO STKstrikeoff sidecutter, 3/1 pattern PMSCB330-SO STKstrikeoff sidecutter, 2/2 pattern PMSCB410-SO STKblade-type, 3/1 pattern PMB311LH STKblade-type, 3/1 pattern PMB312RH STKblade-type, 3/1 pattern PMB330RH STKblade-type, 3/1 pattern PMB331LH STKsidecutter, blade-type, RH, 2/2 PMB102RH STKsidecutter, blade-type, LH, 2/2 PMB103LH STKsidecutter, B-O, tooth-type, LH PM330X310 N.Ssidecutter, B-O, tooth-type, RH PM331X310 N.Ssidecutter, tooth-type, RH PM102X400 N.Ssidecutter, tooth-type, LH PM103X400 N.S

Hensley Attachmentsstyle description part no. rcv. disc. non stock used on

one-piece tooth, B-O PM099HX STKtooth, ctr., long, early style PM50CHX STKtooth, LH. long, early style PM50LH STKtooth, RH. long, early style PM50RH STKtooth, ctr. PM100CHX STKtooth, ctr. PM1020HX STKtooth, ctr., short PM500CHX STKtooth, LH PM100LH STKtooth, RH PM100RH STKtooth, LH, short PM500LH STKtooth, RH, short PM500RH STKtooth, ctr. PM1000HX STKtooth, LH PM1000LH STKtooth, RH PM1000RH STKtooth, ctr., continuous edge PM3000HX STKcontinuous edge ctr. tooth PM4330CHX STKcontinuous edge W-O nose PM4330WN STKclosed lifting eye, large I.D., 10-20,000 lb. excaPM1025HX STKclosed lifting eye, large I.D., 20-30,000 lb. excaPM2030HX STKclosed lifting eye, large I.D., 30-40,000 lb. excaPM3040HX STKclosed lifting eye, large I.D., 40-50,000 lb. excaPM4050HX STKclosed lifting eye, large I.D., 50-60,000 lb. excaPM5060HX STKcrnr. gusset PMCG6 STKcrnr. gusset PMCG9 STKcrnr. gusset PMCG12 STKclosed eye lifting hook PM1030HHX STKclosed eye lifting hook PM2060HHX STKclosed eye lifting hook PM60100HX N.S.tooth, LH PM3000LH STKtooth, RH PM3000RH STKtooth, ctr., heavy PM3000H STKtooth, LH, heavy PM3000HLH STKtooth, RH, heavy PM3000HRH STKtooth, ctr. (round & T bucket) PM3000RC STKblade (156 nose) PM11V16L STKblade (156 nose) PM11V16R STKblade (162 nose) PM13V16L N.S.blade (162 nose) PM13V16R N.S.roll pin (2.25") PMP100 STKroll pin PM301P STKroll pin PM1000P STKpin PM9J2358P STKadpt., ctr. (156 nose) PM110HX STKadpt., LH (156 nose) PM110LH STKadpt., RH (156 nose) PM110RH STKadpt., ctr. (parabolic 400 nose) PM510HX STKadpt., LH (parabolic 400 nose) PM510LH STKadpt., RH (parabolic 400 nose) PM510RH STKadpt., ctr. PM1010HX STKadpt., LH PM1010LH STKadpt., RH PM1010RH STKadpt., ctr., continuous edge PM3010HX STKadpt., LH, continuous edge PM3010LH STKadpt., RH, continuous edge PM3010RH STKadpt., ctr. (round & T bucket) PM3010RC STKadpt., RH/LH (round & T bucket), less W-O nos PM3010RRL STKnose, W-O, ctr. PM1010WN STKnose, W-O LH PM1010WNL STKnose, W-O, RH PM1010WNR STKnose, W-O PM9J4354WN STK

Hensley - Teeth by Seriesadpt. nose, W-O PM156WN STKnose, W-O PM220WN STKnose, W-O, LH (round & T bucket), ref. 3010RRPM3010LWN STKnose, W-O, ctr., (round & T bucket) PM3010WNRC STKnose, W-O, RH (round & T bucket), ref. 3010RRPM3010RWN STKnose, W-O, ctr. PM1030WN STKnose, W-O, ctr., continuous edge PM3010WN STKnose, W-O, LH, continuous edge PM3010WNL STKnose, W-O, RH, continuous edge PM3010WNR STKwasher (old #3G9549W) PM6Y9459W STK

Hensley - Teeth by SeriesHensley Ripper Teeth - Applications

156 Seriesstyle description part no. rcv. disc. non stock used onc tiger TT156 STK

long TX156 STKb star PMS156 STK

heavy duty star PMS156HD STK tiger, heavy duty PMT156HD STKflare, 4.375 PMX156F STKheavy PMX156H STKextra long PMX156LP STKroll pin PM156 STKbox pin (B922B) PM922 STKripper box PMB922B STKripper sh. (B922B) PM922X156 STKpin removal tool for P100, P156 PMPRT156 STKnose, W-O PM156WN STK


tooth, tiger TT160 STKtooth, std. TX160 STK

tooth, star PMS160 N.S.tooth, heavy duty PMX160HD STKadpt., B-O, 1-1/2 leg, 1.18 throat, 33 degrees ( PM552X160 STKadpt., W-O, bottom leg, 1-1 1/4 edge, 30 degrePM850X160 STKroll pin PM160 STKbox pin (B926A) PM926 STKripper box PMB926A STKripper sh. (B922B) PM922X160 STKripper sh. (B926A) PM926X160 STKpin removal tool for P160 PMRT160 STK


box ripper sh. (B922B) PM 922X162 STKbox ripper sh. (B926A) PM 926X162 STK


teeth, tiger PMT501 STKteeth, std. PM501HX STK

ripper box PMB944 STKripper box PMB977 STKbox pin (B944) PMP944 STKflex pin (tooth) PM501P STKbox pin (B977) PMP977 STKripper sh. (B944) PM944-501 STKripper sh. (B977) PM977-501 STKadpt. nose, W-O PM501WN STK


tiger tooth PMT702 STKtiger tooth, long PMT702L STKtwin tiger tooth PMX702WT STKtwin tiger tooth, long PMX702WTL STKstd. tooth PM702HX STKflex pin PM702P STKripper sh., 28" (B977) PM977-702 STKripper sh., 38" (B977) PM977-702L STKadpt. nose, W-O PM702WN STK

Hensley - Specifications

156 Series (Top Mount)style description part no. a b c d lbs.

T Fanggs TF156 6" 1-3/4" 1-5/8" 1-5/8" 3.9T standard TX156 4-1/4" 1-3/4" 1-5/8" 1-5/8" 1.3T tiger TT156 6-1/4" 1/8" 1-5/8" 1-5/8" 1.8T twin tiger TX156WT 6" 3-1/8" 1-5/8" 1-5/8" 3.3T tooth, star PMS156 6" 1-1/8" 1-5/8" 1-5/8" 2.4T star h-d PMS156HD 6-1/16" 1-1/8" 1-5/8" 1-5/8" 2.7T tiger h-d PMT156HD 6-1/4" point 1-5/8" 1-5/8" 2.1T flare PMX156F 5" 4-3/8" 1-5/8" 1-5/8" 2.8T heavy PMX156H 5-1/2" 2 1-5/8" 1-5/8" 2.6T extra long PM156XLP 6" 2-1/4" 1-5/8" 1-5/8" 3.6T tooth, long PMX156L 1.7T tooth, twin tiger long PMX156WTL 2.5

adpt., ctr. (156 nose) PM110HX 8.2adpt., RH (156 nose) PM110RH 5.9adpt., LH (156 nose) PM110LH 6.1adpt., nose, W-O PM156WN 1.8blade (156 nose) PM11V16L 23.0blade (156 nose) PM11V16R 23.0adpt., W-O, 1-1/2 leg, .625" lip PM230X156 3.7adpt., B-O, .81" thr., 29deg JCB 3C PM300X156 4.9adpt., B-O, LH, crnr., refer to 300X156 PM301X156 10.0adpt., B-O, RH, crnr. refer to 300X156 PM302X156 10.0adpt., B-O, Deere no. U-41344 PM344X156 6.5adpt., B-O, 1-1/2 leg, .93" throat PM350X156 6.6adpt., B-O, 2 leg, step, Case #D35642 PM401X156 6.6adpt., W-O, 1-1/2 leg, .625" lip PM548X156 4.0adpt., W-O, 1-1/2 leg, .875" lip PM549X156 4.0adpt., W-O, 1-1/2 leg, 1" lip PM550X156 4.7adpt., B-O, .625" throat, 21deg PM551X156 6.0adpt., W-O, 1-1/2 leg, .75"" lip PM552X156 5.4adpt., W-O, flush, .75"" to .875" PM681X156 4.2adpt., B-O, step (drott TD-6) PM682X156 6.2adpt., B-O, 2 leg, 1.18" throat PM683X156 6.4adpt., B-O, 2 leg, .81" throat PM684X156 4.0adpt., W-O, bttm. leg, 1" lip PM805X156 4.0adpt., W-O, bttm. leg, .625" to .875", ditch wit PM835X156 3.5adpt., W-O, bttm. leg, .75"" to 1.0" lip PM836X156 5.012" lip blade w/3 noses PM12M156-12AHX 29.814" lip blade w/3 noses PM14M156-12AHX 32.018" lip blade w/4 noses PM18M156-12AHX 44.324" lip blade w/5 noses PM24M156-12AHX 57.0ripper box PMB922B 14.7nose weld-on PM156WN 3-1/4" 2-1/4" 1.8

Type

Type 2

Type 3

T

Type 1

Hensley - Specifications160 Series (Top Mount)style description part no. a b c d lbs.

T Fanggs TF160 6-1/4" 2-1/8" 1-5/8" 2-3/8" 4.2T standard TX160 6-7/8" 2-1/4" 1-5/8" 2-3/8" 4.7T tiger TT160 8-3/4" 1/4" 1-5/8" 2-3/8" 5.3T twin tiger TX160WT 8-3/8" 3-5/8" 1-5/8" 2-3/8" 7.4T flare TX160F 4-1/2" 6-5/8" 1-5/8" 2-3/8" 5.8T star PMS160 7-3/4" 1" 1-5/8" 2-3/8" 4.4T std h.d. PMX160HD 6-5/8" 2-5/16" 1-5/8" 2-3/8" 4.52 adapter T658X160 8" 4-3/8" 1-1/16" 30° 15.7

adapter PM552X160 11.4adapter PM850X160 6" 5-1/2" 1-1/4" 30° 7.5adpt., B-O, 2 leg, .81" throat, (TCM 830) PM168X160 9.7adpt., B-O, RH, crnr. PM169X160 10.4adpt., B-O, LH, crnr. PM170X160 10.4adpt., B-O, 2 leg 1.125" throat PM204X160 13.6adpt., B-O, 2 leg, Cat #8J2930 PM309X160 16.0adpt., B-O, 2 leg, Komatsu #1 13-70-22140 PM310X160 9.2adpt., B-O, 1-1/2 leg, 1.31" throat (Clark 55C) PM314X160 16.2adpt., B-O, 2 leg, .93" throat PM504X160 11.8adpt., B-O, step PM510X160 12.7adpt., B-O, step PM553X160 10.5adpt., B-O, 2 leg, .90" throat, (KSS-65Z) PM650X160 11.6adpt., B-O, RH, crnr., refer to 650X160 PM653X160 22.0adpt., B-O, LH, crnr., refer to 650X161 PM654X160 22.0adpt., B-O, step PM702X160 14.7adpt., B-O, 2 leg, 1.31" throat PM706X160 12.0adpt., B-O, 2 leg, 1.18" throat PM717X160 10.2adpt., B-O, 2 leg, 1.06" throat PM718X160 14.6adpt., B-O, 2 leg, 1.06" throat PM750X160 9.5adpt., B-O, H&L #L2145-23, L-4013-23 PM775X160 7.9adpt., B-O, Case/Drott 4-in.-1, #26269 PM787X160 15.3adpt., B-O, Case/Drott 4-in.-1, #229291 PM792X160 11.5adpt., W-O, top leg, H&L #809-24 PM809X160 8.0adpt., B-O, step PM840X160 10.8adpt., B-O, 1.18" throat, Deere U41344 PM861X160 9.6adpt., B-O, 2 leg, 1.31" throat PM927X160 12.0adpt., W-O, bttm. Leg PM928X160 10.0ripper box PMB926A 58.7adpt. nose, W-O PM160WN 4.2

Hensley - Specifications162 Series (Side Mount)style description part no. a b c d lbs.

T tooth, tiger PMT162 4.7T tooth, std. PMX162 3.5T tooth, flare, 4" PMX162F 4.2T tooth, heavy duty PMX162HD 4.2T tooth, twin tiger PMX162WT 7.2

adpt., B-O, 1.31" throat, 30 deg, Clark 55C PM314X162 16.2adpt., B-O, step PM510X162 12.7adpt., B-O, step PM702X162 14.7adpt., B-O, 2 leg, 1.06" throat PM750X162 10.0adpt., W-O, bttm. leg, 1" to 1.25" PM850X162 7.5adpt., B-O, 1.06" throat, (VME L-70) PM901X162 17.1adpt., B-O, 1.25" throat, (VME L-90) PM902X162 15.9adpt., B-O, LH, refer to 902X162 PM903X162 24.1adpt., B-O, LH, refer to 902X163 PM904X162 24.2adpt., B-O, 2 leg, 1.31" throat PM927X162 12.0

blade (162 nose) PM13V16R 26.6 blade (162 nose) PM13V16L 26.6 adpt. nose, W-O PM162WN 4.5



T Fanggs TF220 7" 2-5/8" 2-1/4" 2-1/8" 6.0T standard TX220 7-1/8" 2-3/4" 2-1/4" 2-1/8" 6.7T tiger TT220 8" 1/4" 2-1/4" 2-1/8" 6.0T twin tiger TX220WT 8" 3-7/8" 2-1/4" 2-1/8" 7.5T flare TX220F 7-1/2" 4-5/8" 2-1/4" 2-1/8" 6.9T abrasion paneled TX220AP 8" 3-1/2" 2-1/4" 2-1/8" 8.8T nose weld-on PM220WN 4-7/8" 3 back 3-1/8 height 5.5T star PMS220 8-1/4" 1-1/2" 2-1/4" 2-1/8" 6.4T abrasion PMX220ABR 8" 3-3/8" 2-1/4" 2-1/8" 10.6T down pitch PMX220DP 2-1/4" 2-1/8" 7.2T twin tiger PMX220WTL 8-3/8" 4-1/8" 2-1/4" 2-1/8" 7.2T tooth, tiger long PMT220L 6.42 adapter T109X220 6" 1-5/16" 30° 15.7

adapter PM100X220 9-1/2" 8-1/2" 1" 30° 15.8adapter PM106X220 9-1/2" 4-1/2" 1" 25° 16.4adapter PM102X220 8-1/2" 7-1/4" 1-1/4" 36° 11.5adapter PM385X220 17.1adapter PM544X220 16.2adapter PM611X220 15.0adapter PM900X220 8-7/8" 8-1/2" 1-1/4" 23° 12.8

adpt., B-O, 2 leg, 1.875" throat PM0C1X220 21.2adpt., B-O, 2 leg, 1.625" throat PM3C1X220 17.5adpt., W-O, 1-1/2 leg, 1" lip PM103X220 15.9

adpt., W-O, notched LH crnr. PM107X220 11.5 adpt., W-O, notched RH crnr. PM108X220 11.5

adpt., B-O, 1.125" throat, (D57S) PM111X220 22.6adpt., B-O, crnr., RH, 1.15 thr PM112X220 19.8adpt., B-O, crnr., LH, 1.15 thr PM113X220 19.8adpt., B-O, 2 leg, .96" throat PM155X220 21.7adpt., B-O, 2 leg, 1" throat PM168X220 16.3adpt., B-O, RH, crnr. PM169X220 17.3adpt., B-O, LH, crnr. PM170X220 17.3adpt., B-O, step, IH #610986C1 PM211X220 17.7adpt., B-O, ctr. (920, 930, 941B)(1U0257) PM257X220 18.2adpt., B-O, crnr., Cat #3G4258 PM258X220 26.0adpt., B-O, crnr., Cat #3G4259 PM259X220 26.0adpt., B-O, step, IH #611606C1(270, 442, 444) PM270X220 19.1adpt., B-O, 2 leg, 1.31" throat PM295X220 21.0adpt., B-O, 2 leg, 1.06" throat PM310X220 24.1adpt., B-O, 1.18" thr, 30deg (Case 750, 850) PM311X220 13.2adpt., B-O, 2 leg 1"" throat, 25deg, Kom D41 PM410X220 15.8adpt., B-O, 1.31" thr, ESCO #4738-25 (W36) PM473X220 14.4adpt., B-O, 2 leg, 1.31" throat PM500X220 22.4adpt., B-O, step, Cat #7J4415 PM613X220 19.8adpt., stake-type (Poclain, PC8) PM615X220 10.3adpt., B-O, ctr. 1.06" throat (Case 621, 855D) PM621X220 17.8adpt., B-O, crnr. (Case 621) PM622X220 25.0adpt., B-O, 2 leg, 1.03" throat PM700X220 17.8adpt., B-O, RH, refer to 700X22 PM701X220 30.0adpt., B-O, LH, refer to 700X22 PM702X220 30.0adpt., B-O, step (Wabco 222G) PM703X220 18.7adpt., B-O, step (Fiat-Allis 161) PM706X220 15.4adpt., B-O, step (Wabco 222G) PM707X220 19.8adpt., B-O, step PM710X220 15.4adpt., B-O, 1.18" throat, (F-A 545B) PM730X220 17.8adpt., B-O, 1.09" throat, Case #D49545 PM747X220 16.2adpt., B-O step PM785X220 19.7adpt., B-O step PM786X220 19.0adpt., B-O, 1-1/2 leg, 1.06" throat PM796X220 18.7

220 Series (Top Mount)

Hensley - Specificationsadpt., B-O, 1-1/2 leg, .875" throat PM797X220 13.5adpt., W-O, 1-1/4 leg, 1.5" throat PM809X220 10.8adpt., B-O, 2 leg, 1.31" throat PM810X220 16.7adpt., B-O, 2 leg, 1" throat PM811X220 19.3adpt., B-O, 2 leg, 1.25" throat PM812X220 25.0adpt., B-O, 1.06" throat, (Case W18) PM818X220 12.0adpt., B-O, 1.31" throat PM824X220 12.4adpt., W-O, bttm. leg, 2" to 2.25" PM855X220 13.7adpt., B-O, 2 leg, 1.375" throat PM856X220 23.0adpt., B-O, 1.68" throat PM857X220 21.5adpt., B-O, step, Deere #T38783 PM860X220 17.2adpt., B-O, 2 leg, 1.31" throat PM927X220 14.0

adpt. nose, W-O PM220WN 5.5

225 Series (Side Mount)style description part no. a b c d lbs.

T tooth, tiger PMT225 5.0T tooth, std. PMX225 6.2T tooth, abr. paneled PMX225AP 8.4T tooth, abr. PMX225ABR 11.0T tooth, flare, 4.5"" PMX225F 6.0T tooth, twin tiger PMX225WT 8.5

adpt., B-O, 2 leg, 1.875" throat PM0C1X225 21.2adpt., W-O, bttm. leg, 2" lip PM102X225 15.8adpt., W-O, 1-1/2 leg, 1" lip PM106X225 16.4adpt., B-O, 1.125" throat PM111X225 22.6adpt., B-O, 2 leg, .96" throat PM155X225 21.7adpt., B-O, rev., crnr., Deere #112163 PM163X225 15.8adpt., B-O, ctr., .81" throat PM164X225 12.3adpt., B-O, ctr., 1.06" throat PM165X225 14.2adpt., B-O, crnr. (544E, 624E) PM191X225 20.5adpt., B-O, 2 leg, 1.06" throat PM257X225 18.2adpt., B-O, LH, crnr., Cat #3G4258 PM258X225 24.8adpt., B-O, RH, crnr., Cat #3G4259 PM259X225 24.8adpt., B-O, 2 leg, 1.06" throat PM310X225 24.1adpt., B-O, 1.43" thr, 22deg, Clark #251 147 PM313X225 23.6adpt., B-O, 1.56" thr, 33deg, Deere T35385 PM385X225 17.1adpt., B-O, 1.31" throat, 22deg (Case W36) PM473X225 14.4adpt., B-O, 1.31" throat, Deere T29886 PM544X225 16.2adpt., B-O, step PM785X225 19.7adpt., B-O, LH, crnr. PM572X225 15.0adpt., B-O, 1.06" throat PM611X225 15.0adpt., B-O, step (Wabco 222G) PM703X225 18.7adpt., B-O, 1.09" throat PM747X225 16.2adpt., B-O, 1-1/2 leg, 1.06" throat PM796X225 18.7adpt., B-O, 1-1/2 leg, .875" throat PM797X225 13.5adpt., B-O, 2 leg, 1.31" throat PM810X225 16.7adpt., B-O, 2 leg, 1" throat PM811X225 19.3adpt., B-O, 1.06" throat PM818X225 12.0adpt., B-O, 1.31", Case #L58824 PM824X225 12.4adpt., W-O, bttm. leg, 2" to 2.25" lip PM855X225 13.2adpt., B-O, 1.68" throat PM857X225 21.5adpt., B-O, step, Deere #T38783 PM860X225 17.2adpt., W-O, flush, 1.25" lip, 2" PM900X225 12.8adpt., B-O, ctr., 1.43" throat PM902X225 24.1adpt., B-O, LH, crnr., refer to 902X225 PM903X225 30.0adpt., B-O, RH, crnr., refer to 902X225 PM904X225 30.0

adpt., nose, W-O PM225WN 5.7


T Fanggs TF290 8-1/4" 3-1/4" 2-7/8" 2-11/16" 10.4T standard TX290 8-1/4" 3-3/16" 2-7/8" 2-11/16" 8.6T tiger TT290 10" 3/16" 2-7/8" 2-11/16" 8.8T twin tiger TX290WT 9-3/4" 4-5/8" 2-7/8" 2-11/16" 10.2T flare TX290F 8" 6-1/4" 2-7/8" 2-11/16" 11.6T abrasion panel TX290AP 8-1/2" 4" 2-7/8" 2-11/16" 10.43 adapter T127X290 7-1/2" 1-1/4" 30° 21.53 adapter T158X290 7-1/2" 1-1/2" 30° 22.7

abrasion PMX290ABR 8-3/16" 3-3/4" 2-7/8" 2-11/16" 10.2adapter PM125X290 10" 9" 1-1/4" 23.2adapter PM150X290 10" 9" 1-1/2" 19.9adapter PM190X290 3-13/32" 4-25/32" 1-5/16" 1-3/16" 21.5adapter PM191X290 21.5adapter PM673X290 2-15/16" 4-3/4" 1-3/8" 1-1/8" 27.5adapter PM822X290 22.0nose template kit for 290, 330 PMA-TEM 11.4nose rebuild kit for 290 series PMA290NR 2.3tooth, sharp, ribbed PMX290SYL 9.2adpt., stake type, ESCO C-19 lip PM119X290 18.8adpt., W-O, 1-1/2 leg, 2" lip PM124X290 24.3adpt., W-O, 1-1/2 leg, RH, 1.75" PM130X290 22.6adpt., W-O, 1-1/2 leg, LH, 1.75" PM131X290 22.6adpt., stake type, Hensley C-19 PM136X290 20.1adpt., B-O, 2 leg, 1.25" thr. PM156X290 31.2adpt., B-O LH crnr. (955L) PM308X290 39.5adpt., B-O RH crnr. (955L) PM309X290 39.5adpt., W-O, bttm. Leg, 1.25"" to 1.5" lip PM383X290 18.7adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) PM430X290 30.0adpt., B-O, 2 leg, 1.93" thr. 23deg, (85Z11) PM480X290 24.3adpt., B-O, LH (85Zll), (req. 486INS) PM486X290 34.8adpt., B-O, RH (85Zll), (req. 486INS) PM487X290 34.8adpt., B-O, LH (80Zlll) PM488X290 37.1adpt., B-O, RH (80Zlll) PM489X290 37.1adpt., B-O, 2 leg, 1.03" thr. (80Z111) PM490X290 23.8adpt., W-O, 1-1/2 leg, 1.375" lip PM580X290 20.2adpt., stake type (Akerman H9, H11) PM589X290 26.6adpt., B-O, ctr., 1.375" thr. PM721X290 21.0adpt., B-O, crnr. (Case 721) PM722X290 24.0adpt., B-O, crnr. (Case 821) PM820X290 27.0adpt., B-O, ctr., 1.31" thr. (Case 821) PM821X290 24.0adpt., B-O rev. crnr. VME L-14 PM904X290 36.2adpt., B-O, 2 leg, 1.56" thr. PM905X290 26.3nose weld-on PM290WN 4-1/4" 3-5/8" 7.3


T std. tooth PM295 8.2T tiger tooth PMT295 8.7T twin tiger tooth PM295WT 10.5T abr. panel tooth PM295AP 10.8T tooth, short, ribbed PM295SYL 10.3T flare tooth PM295F 12.8

adpt. 1-1/4" lip PM127X295 21.9adpt., C-19 cast lip PM136X295 20.6adpt. 1-1/2" lip PM158X295 22.8adpt. B-O L.H. PM308X295 39.8adpt., B-O R.H. PM309X295 39.8adpt. bttm. leg W-O PM383X295 19.2adpt., B-O PM430X295 30.2adpt., stake type, Akerman H7 PM589X295 26.8adpt., W-O nose PM295WN 8.1

300 Series (Side Mount)style description part no. a b c d lbs.

T tooth, tiger PMT300 10.5T tooth, std. PMX300 7.5T tooth, abr. PMX300ABR 14.5T tooth, abr. paneled PMX300AP 9.8T tooth, flare, 6"" PMX300F 7.5T tooth, heavy duty rock PMX300R 12.5T tooth, twin tiger PMX300WT 13.3 adpt. nose, W-O PM300WN 7.2


T Fanggs TF310 7-1/2" 3-1/4" 3" 2-1/8" 10.4T standard TX310 8" 3-3/8" 3" 2-1/8" 8.0T tooth, std., 4" wide PMX310-4 8.0T tiger TT310 9-7/8" 1/4" 3" 2-1/8" 11.6T twin tiger TX310WT 9-5/8" 4-3/4" 3" 2-1/8" 12.2T flare TX310F 7-7/8" 6" 3" 2-1/8" 8.6T abrasion paneled TX310AP 8-1/4" 4" 3" 2-1/8" 10.32 adapter T153X310 7" 1-9/16" 30° 21.4

adapter PMX310ABR 8-3/4" 4" 3" 2-1/4" 14.5key PMK668 2.0refer also to 142X330 PM110X310 24.5adpt., stake-type, ESCO C-19 lip PM119X310 18.0adpt., W-O, bttm. leg, 1.5" lip PM122X310 17.5adpt., W-O, l-1/2 leg, 2" lip PM124X310 23.0adpt., W-O, flush, 1.25" lip PM125X310 21.9adpt., W-O, 1-1/2 leg, 1.25" lip PM127X310 20.2adpt., W-O, 1-1/2 leg, 1.25" lip PM128X310 20.5adpt., W-O, RH, 1-1/2 leg, 1.75" PM130X310 21.4adpt., stake-type, C-19 lip (reqs P136) PM136X310 18.7adpt., B-O, 1-1/2 leg, 1.43" throat PM138X310 22.5adpt., flush, 1.5" str. lip PM150X310 19.7adpt., RH, flush, 1.5" sp. lip PM151X310 19.7adpt., LH flush, 1.5" sp. lip PM152X310 19.5adpt., W-O, RH, 1-1/2 leg, 1.5" lip PM154X310 22.1adpt., W-O, LH, 1-1/2 leg, 1.5" lip PM155X310 22.1adpt., B-O, 2 leg, 1.25" thr. PM156X310 30.5adpt., W-O, 1-1/2 leg, 1.5" lip PM158X310 21.9adpt., W-O, LH, notched crnr. PM159X310 15.7adpt., W-O, RH, notched crnr. PM160X310 15.7adpt., B-O, 2 leg, 1.43" thr. PM168X310 33.5adpt., B-O, RH, crnr. PM169X310 37.2adpt., B-O, LH, crnr. PM170X310 37.6adpt., B-O, 1.46" thr. Komatsu D65, D75 PM181X310 29.0adpt., B-O, 2 leg, 1.31" thr. PM185X310 24.0adpt., B-O, 2 leg, 1.81" throat PM301X310 24.0adpt., B-O, LH crnr. (955L) PM308X310 37.4adpt., B-O, RH crnr. (955L) PM309X310 37.4adpt., B-O, 1.31" thr., 22deg, Case 1450 PM317X310 25.1adpt., B-O, specialty item PM323X310 33.5adpt., W-O, bttm. leg, 1.25"" to 1.5" lip PM383X310 17.9adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) PM430X310 29.5adpt., W-O, 1-1/2 leg, 1" lip PM494X310 23.7adpt., B-O, step PM495X310 35.0adpt., B-O, 2 leg, 1.81" thr, Furukawa 320A PM550X310 31.6adpt., W-O, 1-1/2 leg, 1.375" lip PM580X310 21.2adpt., stake-type (req. K668) PM668X310 21.5adpt., B-O, 1-1/2 leg, 1.375" thr PM742X310 23.0adpt., B-O, step PM756X310 24.7adpt., B-O, step PM758X310 36.2adpt., B-O, step PM759X310 33.0adpt., B-O PM812X310 26.9adpt., W-O, bttm. leg, 1.5" lip PM822X310 22.0adpt., W-O, bttm. leg, .75"" to .875" PM844X310 17.9adpt., W-O, 1.375" special lip PM845X310 26.9adpt., B-O, 2 leg, 1.81" thr. (HD 6G, 12G) PM859X310 31.4adpt., W-O, flush, 1.5" str. lip PM900X310 19.5adpt., W-O, flush, LH, sp. lip PM901X310 19.7adpt., W-O, flush, RH, sp. lip PM902X310 19.9nose weld-on PM310WN 4-3/4" 3-3/4" 7.5



T Fanggs TF330 9-1/4" 3-5/8" 3-13/32" 3-3/16" 15.3T standard TX330 9-1/4" 3-5/8" 3-13/32" 3-3/16" 11.9T tiger TT330 11-5/8" 3/16" 3-13/32" 3-3/16" 11.9T twin tiger TX330WT 11-5/8" 5-1/4" 3-13/32" 3-3/16" 14.7T flare TX330F 9-5/8" 7-1/4" 3-5/8" 3-1/8" 18.1T abrasion panel TX330AP 9-1/2" 4-1/2" 3-5/8" 3-1/8" 15.4T tooth, sharp, ribbed PM X330SYL 14.9T short rock PMX330SR 8-3/8" 4-1/4" 3-5/8" 3-1/8" 14.4

abrasion PMX330ABR 9-1/4" 4-1/4" 3-5/8" 3-1/8" 15.52 adapter T158X330 8" 1-9/16" 30° 35.2

adapter PM190X330 32.9adapter PM743X330 64.0adapter PM744X330 44.0adapter PM822X330 28.3adapter PM937X330 32.9nose rebuild kit for 330 Series PMA330NR 2.7lip fastener, C-19 lips (136X330, 136X310) PMP136 0.8lip fastener, C-29 lips (236X330) PMP236 2.1steel wedge PMW330 0.8adpt., stake-type, Hensley C-19 PM136X330 24.8adpt., W-O, LH, notched crnr. PM159X330 28.7adpt., W-O, RH, notched crnr. PM160X330 28.7adpt., W-O, 1-1/2 leg, 1.625" lip PM225X330 30.4adpt., stake-type, Hensley C-29 PM236X330 47.8adpt., B-O specialty item (Sauerman) PM323X330 41.4adpt., W-O, bttm. leg, 1.25"" lip, 23deg PM383X330 23.5adpt., B-O, ctr. (VME L150, L180) PM901X330 41.0adpt., B-O, ctr. (Case 921) PM921X330 29.0adpt., W-O, LH, notched crnr. PM935X330 29.4adpt., W-O, RH, notched crnr. PM936X330 29.4nose weld-on PM330WN 5-1/8" 4-1/4" 10.9


T std. tooth PM335 12.5T abr. panel tooth PM335AP 15.1T flare tooth PM335F 17.9T tooth, short, ribbed PM335SYL 15.3T tiger tooth PMT335 13.2T twin tiger tooth PM335WT 15.3

adpt., 1.5" lip PM158X335 34.6adpt., W-O, flush 1.625" - 1.75" lip, 30 deg PM190X335 34.5adpt., C-29 Hensley cast lip PM236X335 48.7adpt., stake (Akerman H12, 14, 16) PM355X335 38.3adpt., L.H. crnr., 1.75" lip PM935X335 31.7adpt., R.H. crnr. 1.75" lip PM936X335 31.7adpt., 1.75" lip PM937X335 33.1adpt., W-O nose PM335WN 12.1


T standard TX350 11" 4" 3-1/2" 2-7/8" 18.4T tooth, tiger PMT350 15.0T tooth, abr. paneled, short PMX350APS 18.7T tooth, flare PMX350F 18.3T tooth, twin tiger PMX350WT 20.7

adpt. nose, W-O PM350WN 14.5


Hensley - SpecificationsT Fanggs TF370 10-1/4" 4" 3-5/8" 3-3/8" 22.9T standard TX370 10-1/4" 4-1/8" 3-5/8" 3-3/8" 17.8T tiger TT370 12" point 3-5/8" 3-3/8" 18.2T twin tiger TX370WT 12" 6" 3-5/8" 3-3/8" 21.0T abrasion paneled PMX370AP 10-7/8" 5" 3-5/8" 3-3/8" 21.4T flare PM370F 10-1/4" 8" 3-5/8" 3-3/8" 22.9T tooth, sharp, ribbed PM X370SYL 19.4T abrasion PM370ABR 11-3/4" 4-5/8" 3-5/8" 3-3/8" 25.6

steel keeper TK370S 1.01 adpt. W-O, 1-1/2 leg, 2" lip T940X370 5-1/4" 10-3/4" 2-1/16" 30° 36.4

fastener for Hensley C-29 lips PMP236 2.1adpt., stake-type, ESCO C-29 lip PM129X370 33.7adpt., W-O, 1.5" lip PM158X370 35.3adpt., stake-type, Hensley C-29 PM236X370 52.0adpt., W-O, bttm. leg, 2" to 2.25" lip PM827X370 35.2adpt. W-O, ctr., 2" lip T940X370 36.4adpt., W-O, RH/LH, 1.75" sp. lip PM936X370 41.9adpt., W-O, ctr., 1.75" str. lip PM937X370 35.6adpt., W-O, LH, 2" flush sp. lip PM947X370 40.5adpt., W-O, RH, 2" flush, sp. lip PM948X370 40.5adpt., W-O, ctr., 2" flush, str. lip PM949X370 38.7nose rebuild kit for 370 Series PMA370NR 4.8nose weld-on PM370WN 5-3/4" 4-5/8" 14.7


T tooth, std. PM385 21.4T tooth, flare PM385F 30.9T tooth, sharp, ribbed PM385SYL 24.9T tooth, tiger PMT385 22.1T tooth, twin tiger PM385WT 24.1

adpt., stake type, Hensley C29 PM236X385 57.0adpt., stake (Akerman H12, 14, 16) PM355X385 44.5adpt., W-O, bttm. leg PM827X385 44.3adpt., W-O, 1-1/2 leg, 1.75" lip PM937X385 44.7adpt., W-O, 1-1/2 leg, 2" lip PM940X385 43.4adpt., W-O, flush, 2" lip PM949X385 51.5adpt., W-O nose PM385WN 19.7


T Fanggs TF400 9-1/4" 4-1/2" 4" 2-7/8" 10.4T standard TX400 10" 4" 4" 2-7/8" 16.2T tiger TT400 12-1/4" 3/8" 4" 2-7/8" 18.6T twin tiger TX400WT 12-1/4" 6" 4" 2-7/8" 24.1T flare TX400F 10-1/2" 8" 4" 2-7/8" 21.6T abrasion paneled TX400AP 10-5/8" 5-1/2" 4" 2-7/8" 21.8T abrasion PMX400ABR 11" 4-3/4" 4" 3" 25.8T abrasion heavy PMX400ABRB 11" 4-3/4" 4" 3" 28.9T short PMX400H 8-7/8" 4-3/4" 4" 3" 21.7T long sharp PMX400LS 12-5/8" 4-1/4" 4" 30 23.0T penetrator narrow PMX400SD 10-3/4" 2-1/4" 4" 3" 17.9

slag pin PMP400SA 0.3slag pin PMP400SB-S 0.3slag pin PMP400SB-OS 0.3

2 adapter T802X400 9" 2-1/16" 30° 48.0adapter PM800X400 40.0wedge key PMK129C 2.5adpt., stake-type, ESCO C-29 lip PM129X400 36.5adpt., stake-type, for Hensley PM236X400 54.0adpt., W-O, 1-1/2 leg, 1.5" lip PM604X400 36.8adpt., W-O, bttm. leg, 2" to 2.25" PM827X400 48.0adpt., W-O, 2 leg, ctr., 2" lip PM830X400 45.3adpt., W-O, notched crnr., LH PM831X400 41.0adpt., W-O, notched crnr., RH PM832X400 41.0adpt., W-O, 1-1/2 leg, 2" lip PM938X400 44.9adpt., W-O, 1-1/2 leg, 2" lip PM940X400 46.0adpt., B-O, 2 leg, 1.75" thr. PM945X400 52.0nose rebuild kit for 410 Series PMA410NR 5.3nose weld-on PM400WN 6" 5-1/4" 16.7


T Fanggs TF410 11-1/4" 4-3/8" 4-1/16" 3-3/4" 28.5T standard TX410 11-3/8" 4-9/16" 4-1/16" 3-3/4" 21.7T twin tiger TX410WT 13-5/8" 6-5/8" 4-1/16" 3-3/4" 27.6T tiger TT410 13-5/8" point 4-1/16" 3-3/4" 22.6T abrasion PMX410ABR 13" 5-1/8" 4-1/16" 3-3/4" 36.3T abrasion paneled PMX410AP 12" 5-1/2" 4-1/16" 3-3/4" 28.3T flare PMX410F 11-3/8" 9" 4-1/16" 3-3/4" 32.9T tooth, long, sharp PMX410LS 25.2T tooth, sharp, ribbed PMX410SYL 26.5

steel keeper TK410S 1.21 adpt. W-O, 1-1/2 leg, 2" lip T940X410 5-1/4" 11" 2-1/16" 30° 43.4

adpt., stake type Hensley C-29 PM236X410 57.0adpt., W-O, 2 leg, 2" str. lip PMA464X410 60.7adpt., W-O, 2 leg, 2" sp. lip PMA465X410 62.4adpt., W-O, 2 leg, 2" sp. lip PMA466X410 62.4adapt., W-O bttm. leg PM827X410 44.2adpt., W-O 1-1/2 leg 2" lip PM890X410 45.8adpt., W-O 1-1/2 leg 1.75" lip PM937X410 44.5nose weld-on PM410WN 19.7


T tiger PMT450 15" point 4-9/16" 4-5/16" 31.3T standard PMX450 12-1/2" 4-7/8" 4-9/16" 4-5/16" 30.2T flare PMX450F 12-1/2" 10" 4-9/16" 4-5/16" 44.8T abrasion PMX450ABR 14-3/8" 5-5/8" 4-9/16" 4-5/16" 46.5T abrasion paneled PMX450AP 13-1/4" 6" 4-9/16" 4-5/16" 40.8T twin tiger PMX450WT 15" 7-1/4" 4-9/16" 4-5/16" 37.5

nose weld-on PM450WN 28.0


T Fanggs TF475 11-7/8" 5/34" 4-3/4" 3-1/2" 40.7T standard TX475 12-1/2" 5/34" 4-3/4" 3-1/2" 39.5T tiger TT475 14-1/4" 1/4" 4-3/4" 3-1/2" 31.1T twin tiger TX475WT 14-3/8" 7" 4-3/4" 3-1/2" 37.0T flare TX475F 11-5/8" 8-7/8" 4-3/4" 3-1/2" 29.9T abrasion paneled TX475AP 13-1/4" 6-1/2" 4-3/4" 3-1/2" 40.02 adapter T303X475 8/14" 2-9/16" 30° 75.0

abrasion PMX475ABR 13" 5-3/4" 4-3/4" 3-1/2" 40.3slag heavy PMX475AH 12-5/16" 5-3/4" 4-3/4" 3-1/2" 43.8slag long PMX475AHL 15" 5-3/4" 4-3/4" 3-1/2" 49.1slag h-bottom PMX475AHS 12-13/16" 6-3/4" 4-3/4" 3-1/2" 59.0long heavy PMX475LP 12-1/8" 6-1/4" 4-3/4" 3-1/2" 39.5slag PMX475S 9-13/16" 5-3/4" 4-3/4" 3-1/2" 30.9tiger long PMT475L 15-1/2" point 4-3/4" 3-1/2" 37.6twin tiger long PMX475WTL 15-1/2" 7" 4-3/4" 3-1/2" 37.6adapter PM988X475 86.3nose weld-on PM475WN 7-1/4" 6-1/2" 28.0


T std. tooth TX500 14" 5-5/8" 5" 4-11/16" 48.5T abrasion panel TX500AP 14-3/4" 6-3/4" 5" 4-11/16" 54.0T ribbed sharp TX500SYL 15-1/2" 6" 5" 4-11/16" 50.0

adapter T806X500 10" 3-1/16" 8" 30° 104.0


T ribbed sharp TX550SYL 18-1/4" 7" 5-7/8" 5-5/8" 91.0adapter T806X550 12" 3-1/16" 9" 30° 165.0


Sidecuttersstyle description part no. a b c d lbs.

strikeoff sidecutter, 3/1 pattern PMSCB220-SO 21.9strikeoff sidecutter, 3/1 pattern PMSCB330-SO 33.0strikeoff sidecutter, 2/2 pattern PMSCB410-SO 41.8blade-type, 3/1 pattern PMB311LH 29.8blade-type, 3/1 pattern PMB312RH 29.9blade-type, 3/1 pattern PMB330RH 45.2blade-type, 3/1 pattern PMB331LH 45.2sidecutter, blade-type, RH, 2/2 PMB102RH 59.2sidecutter, blade-type, LH, 2/2 PMB103LH 59.5sidecutter, B-O, tooth-type, LH PM330X310 28.0sidecutter, B-O, tooth-type, RH PM331X310 28.0sidecutter, B-O, tooth-type, RH PM102X400 61.0sidecutter, B-O, tooth-type, LH PM103X400 61.0

Hensley Attachmentsstyle description part no. a b c d lbs.

one-piece tooth, B-O PM099HX 3.5tooth, ctr., long, early style PM50CHX 21.0tooth, LH. long, early style PM50LH 21.0tooth, RH. long, early style PM50RH 71.5tooth, ctr. PM100CHX 11.7tooth, ctr. PM1020HX 2.6tooth, ctr., short PM500CHX 21.0tooth, LH PM100LH 3.1tooth, RH PM100RH 3.1tooth, LH, short PM500LH 21.2tooth, RH, short PM500RH 21.0tooth, ctr. PM1000HX 2.5tooth, LH PM1000LH 1.8tooth, RH PM1000RH 1.8tooth, ctr., continuous edge PM3000HX 6.9continuous edge ctr. tooth PM4330CHX 13.8continuous edge W-O nose PM4330WN 22.5closed lifting eye, large I.D., 10-20,000 lb. excav. PM1025HX 4.4closed lifting eye, large I.D., 20-30,000 lb. excav. PM2030HX 10.0closed lifting eye, large I.D., 30-40,000 lb. excav. PM3040HX 18.4closed lifting eye, large I.D., 40-50,000 lb. excav. PM4050HX 34.0closed lifting eye, large I.D., 50-60,000 lb. excav. PM5060HX 61.0crnr. gusset PMCG6 2.1crnr. gusset PMCG9 6.8crnr. gusset PMCG12 16.6closed eye lifting hook PM1030HHX 8.6closed eye lifting hook PM2060HHX 16.0closed eye lifting hook PM60100HX 32.8tooth, LH PM3000LH 5.9tooth, RH PM3000RH 5.9tooth, ctr., heavy PM3000H 6.7tooth, LH, heavy PM3000HLH 5.9tooth, RH, heavy PM3000HRH 5.9tooth, ctr. (round & T bucket) PM3000RC 8.0blade (156 nose) PM11V16L 23.0blade (156 nose) PM11V16R 23.0blade (162 nose) PM13V16L 26.6blade (162 nose) PM13V16R 26.6adpt., ctr. (156 nose) PM110HX 8.2


Hensley Attachmentsstyle description part no. a b c d lbs.

adpt., LH (156 nose) PM110LH 6.1adpt., RH (156 nose) PM110RH 5.9adpt., ctr. (parabolic 400 nose) PM510HX 70.5adpt., LH (parabolic 400 nose) PM510LH 40.0adpt., RH (parabolic 400 nose) PM510RH 40.0adpt., ctr. PM1010HX 7.0adpt., LH PM1010LH 4.5adpt., RH PM1010RH 4.5adpt., ctr., continuous edge PM3010HX 19.1adpt., LH, continuous edge PM3010LH 14.7adpt., RH, continuous edge PM3010RH 14.7adpt., ctr. (round & T bucket) PM3010RC 36.0adpt., RH/LH (round & T bucket), less W-O nose PM3010RRL 17.8nose, W-O, ctr. PM1010WN 3.2nose, W-O, LH PM1010WNL 2.2nose, W-O, RH PM1010WNR 2.2nose, W-O PM9J4354WN 10.7nose, W-O PM156WN 1.8nose, W-O PM220WN 5.5nose, W-O, LH (round & T bucket), ref. 3010RRL PM3010LWN 7.5nose, W-O, ctr. (round & T bucket) PM3010WNRC 10.5nose, W-O, RH (round & T bucket), ref. 3010RRL PM3010RWN 7.5nose, W-O, ctr. PM1030WN 2.6nose, W-O, ctr., continuous edge PM3010WN 8.9nose, W-O, LH, continuous edge PM3010WNL 6.9nose, W-O, RH, continuous edge PM3010WNR 6.9washer (old #3G9549W) PM6Y9459W 0.1

Hensley Ripper Teeth - Specifications156 Seriesstyle description part no. a b c d lbs.

T tooth, tiger TT156 6-1/4" 1/8" 1-5/8" 1-5/8" 1.8T tooth, long TX156L 1.7T tooth star PMS156 6" 1-1/8" 1-5/8" 1-5/8" 2.4T tooth, heavy duty star PMS156HD 6-1/16" 1-1/8" 1-5/8" 1-5/8" 2.7T tooth , tiger, heavy duty PMT156HD 6-1/4" point 1-5/8" 1-5/8" 2.1T tooth, flare, 4.375 PMX156F 5" 4-3/8" 1-5/8" 1-5/8" 2.8T tooth, heavy PMX156H 5-1/2" 2" 1-5/8" 1-5/8" 2.6T tooth, extra long PMX156LP 3.6

roll pin PM156 0.1ripper box PMB922B 14.7ripper sh. (B922B) PM922X156 23.0nose, W-O PM156WN 1.8


T tooth, tiger TT160 4.2T tooth, std. TX160 3.5

T tooth, star PMS160 4.4T tooth, heavy duty PMX160HD 4.5

adpt., B-O, 1-1/2 leg, 1.18 throat, 33 degrees (JD444)PM552X160 11.4adpt., W-O, bottom leg, 1-1 1/4 edge, 30 degrees PM850X160 7.5ripper box PMB926A 58.7ripper sh. (B922B) PM922X160 22.6ripper sh. (B926A) PM926X160 50.0



box ripper sh. (B922B) PM922X162 23.6box ripper sh. (B926A) PM926X162 50.0


T teeth, tiger TT501 12.5T teeth, std. PM501HX 10.7

ripper box PMB944 80.0ripper box PMB977 164.0ripper sh. (B944) PM944-501 72.5ripper sh. (B977) PM977-501 114.0nose, W-O PM501WN 14.0


T tiger tooth TT702 25.2T tiger tooth, long TT702L 26.9T twin tiger tooth PMX702WT 31.0T twin tiger tooth, long PMX702WTL 30.0T std. tooth PM702HX 25.5

ripper sh., 28" (B977) PM977-702 141.0ripper sh., 38" (B977) PM977-702L 210.4nose, W-O PM702WN 37.8

Replacements for Hensley Products Retainers

Hensley17


TK290290 Series

TK330330 Series

TP400HD350, 400 Series

TP475475 Series


Replacements for Hensley Products Retainers

Hensley18


TP156 - 156 Series (Except Fanggs)

TF13P - 156 Series (Fanggs or Other)

TP160 - 160; 220; 310 Series (Except 310 Fanggs)

TP160L - 310 Series Fanggs


John Deere Replacements for H & L Products

Various information can be determined from the part number system. Refer to thefollowing charts for basic part numbering information.

Part Number Explanation for TeethPart Number Explanation H & L ProductsPrefix Suffix Explanation

TF D Fangg DiggingTF L Fangg LoadingT StandardT F FlareT R RockT SP StandardT L LongT ST Star

Note:1 or 2 digits in the part numberindicates fabricated teeth.

3 digits in the part numberindicates steel or ADI teeth.

TF_P indicates Fanggs Flex Pin.T_P indicates STD Flex Pin.

T WT Twin TigerTT Tiger

A, C Crimp-OnCR Crimp-On Rock

Examples:Part Number T250F 25 Series Flare ToothPart Number T230ST 23 Series Star Tooth

Part Number Explanation for AdaptersPart Number Explanation for Replacement H & L AdaptersRelate the correlating digit and part no. to the explanation below:Digit: 1 2 3 4 5 6 7 8

Part No. T 4 2 7 X 2 4 0 T427X240 = Weld-On Center Adapter for 24Series

Digit Explanation1 (T) John Deere Part2 Adapter Style Code

1 - Bolt-On Center2 - Bolt-On End3 - Weld-On End4 - Weld-On Center5 - Weld-On Left-Hand6 - Weld-On Right-Hand7 - Weld-On Bottom Leg8 - Weld-On Flush Mount9 - Scarifier/Ripper

3-4 Leg Spread (mm)5 (X) Adapter Part

6-7-8 Tooth Series

Fanggs Digging Teeth(TF_D) (Non-Centerline)

• For general-purpose-to-heavy digging.

• Provides a clean start andclose crowd.

Fanggs Loading Teeth(TF_L) (Non-Centerline)

• For general purpose to heavydigging/loading conditions.

• Flat bottom for better bucketcontrol.

Flare Teeth(T_F) (Centerline)

• For digging in loose andmud-like conditions.

Standard Teeth(T_SP) (Non-Centerline)

• For general-purpose toheavy-duty digging andloading

• Excellent penetration andwear.

Standard Teeth Fabricated(T_) (Non-Centerline)

• For light-duty, generaldigging and applications.

Long Rock Teeth(T_R) (Non-Centerline)

• For heavy-duty and extraheavy-duty applications.

• Additional wearlife.

Star Teeth(T_ST) (Non-Centerline)

• Excellent penetration inrock, hardpan, and frost.

Tiger Teeth(TT_) (Non-Centerline)

• High penetration for frost andtough material.

Twin Tiger Teeth(T_WT) (Non-Centerline)

• For digging and loading inextremely tight material.

• Use as a corner tooth withtiger teeth in the center.

John Deere Replacements for H & L Products

Various information can be determined from the part number system. Refer to thefollowing charts for basic part numbering information.

Part Number Explanation for TeethPart Number Explanation H & L ProductsPrefix Suffix Explanation

TF D Fangg DiggingTF L Fangg LoadingT StandardT F FlareT R RockT SP StandardT L LongT ST Star

Note:1 or 2 digits in the part numberindicates fabricated teeth.

3 digits in the part numberindicates steel or ADI teeth.

TF_P indicates Fanggs Flex Pin.T_P indicates STD Flex Pin.

T WT Twin TigerTT Tiger

A, C Crimp-OnCR Crimp-On Rock

Examples:Part Number T250F 25 Series Flare ToothPart Number T230ST 23 Series Star Tooth

Part Number Explanation for AdaptersPart Number Explanation for Replacement H & L AdaptersRelate the correlating digit and part no. to the explanation below:Digit: 1 2 3 4 5 6 7 8

Part No. T 4 2 7 X 2 4 0 T427X240 = Weld-On Center Adapter for 24Series

Digit Explanation1 (T) John Deere Part2 Adapter Style Code

1 - Bolt-On Center2 - Bolt-On End3 - Weld-On End4 - Weld-On Center5 - Weld-On Left-Hand6 - Weld-On Right-Hand7 - Weld-On Bottom Leg8 - Weld-On Flush Mount9 - Scarifier/Ripper

3-4 Leg Spread (mm)5 (X) Adapter Part

6-7-8 Tooth Series

Fanggs Digging Teeth(TF_D) (Non-Centerline)

• For general-purpose-to-heavy digging.

• Provides a clean start andclose crowd.

Fanggs Loading Teeth(TF_L) (Non-Centerline)

• For general purpose to heavydigging/loading conditions.

• Flat bottom for better bucketcontrol.

Flare Teeth(T_F) (Centerline)

• For digging in loose andmud-like conditions.

Standard Teeth(T_SP) (Non-Centerline)

• For general-purpose toheavy-duty digging andloading

• Excellent penetration andwear.

Standard Teeth Fabricated(T_) (Non-Centerline)

• For light-duty, generaldigging and applications.

Long Rock Teeth(T_R) (Non-Centerline)

• For heavy-duty and extraheavy-duty applications.

• Additional wearlife.

Star Teeth(T_ST) (Non-Centerline)

• Excellent penetration inrock, hardpan, and frost.

Tiger Teeth(TT_) (Non-Centerline)

• High penetration for frost andtough material.

Twin Tiger Teeth(T_WT) (Non-Centerline)

• For digging and loading inextremely tight material.

• Use as a corner tooth withtiger teeth in the center.

H & L ProductsNew Product

Polyurethane "Swamper"


f standard T2Ad long rock T2AR- adapter T716X2A JD: 172TX

adpt., W-O, flush PML2520W2AHX


d long rock T3CRh flare T3CFa standard PMT3Ca standard PM3CHXL- adapter T716X3C JD: 27ZTS, 35ZTS

adpt., W-O, flush, cast-in placPM1001-3CHXadpt., W-O, flush PM1002-3CHX


g fanggs d TF23De fanggs l TF23L- pin TF23Pa standard T230SPf standard T23b tiger TT230Lc twin tiger T230WTLh flare T230Fi star T230STd long rock T23Rh flare PM23HXFj Swamper T230SWPRi tooth, star (heavy duty) PMS230- pin T23P- pin PM23PB- pin PM23PC- pin PM23PD- adapter T417X230- adapter T728X230- adapter U43792- adapter PM230010- adapter PM2300FL

adpt., W-O, long leg on bttm.PMD834-23HXadpt. nose, W-O PM23WNadpt., W-O, .875" lip PM2740AW-23adpt., W-O, .75" lip PM2740MW-2312" lip blade, w/(3) PM12M480-12A18" lip blade w/4 noses PM18M480-12A24" lip blade w/5 noses PM24M480-12A

JD: Buckets with 23 Series-type adapter, 210C, 210CL, 300D, 500C, 510, 500A, 500B, 310, 310A, 310B, 310C, 310D, 310E, 310SE, 401D, 410, 410B, 410C, 410D, 410E, 315C, 315D, 315E, 510B, 510C, 510D, 610B, 610C, 710B, 710C, 710D, 315SE, 50ZTS, Skid-Steer: JD14, JD24, JD24-A, Case: 480F, 580K, 580L, 590, 590L, 680L, 780D, Competitive: Buckets with 23 Series-type adapters, Ford: 555D, 575D, 655D, 710D, 755B

H & L - Applications24 Seriesstyle description part no. rcv. disc. non stock used on

a standard T240 Competitive: Backhoes with 24 Series-type adapters.a standard PM24HD- rock PM24RI star PMS240b tiger TT240c twin tiger T240WTd long PM24SPHX- sharp PM24HXSSh tooth, flare, 4" tip PM24HXF- pin T24P- pin PM24PBHX- adapter T427X240

adpt., W-O, misc. PM809-24HX N.S.adpt., W-O, 1.25" lip PM2740-24HXadpt., nose, W-O PM24WN N.S.


g fanggs d TF252- pin TF25Pa standard T252h flare T252FI star T252STc twin tiger PM250TWd long PM251HX- pin T25P- oversize pin PM25/26PD- adapter PM2500150- adapter T440X252

adpt., W-O, long leg on bttm.PM855-252HX N.S.adpt., W-O, 1.25" lip PM2740AW-252adpt., W-O, 1.625" lip PM2740FW-252adpt., W-O, long leg on bttm.PM3000W-252HX N.S.adpt., B-O (case 850/1150B) PML4079-252HX N.S.

style description part no. rcv. disc. non stock used ona standard T260a standard PM26HXb tiger PMT26

pin T25Poversize pin PM25/26PD


a standard T271a standard PM27a standard PM271HXh flare 7" PM27HXFd long PM27HXLb tiger PMT27c twin tiger PM27WT N.S.- pin T27P

adpt., W-O, long leg on bttm.PM3000W-27HX N.S.- adapter PM2700150

Competitive: Excavators with 27 Series-type adapters, Komatsu: PC150LC-5, PC200LC-5

26 Series

JD: 690, 690A, 690B, 690C, 690D, 690E, 200LC, 120LC Competitive: Excavators with 25-Series type adapters

670, 670A, 670B, 672A, 672B, 170, 770A, 770B, 772A772B, 772D BH, 772BH

H & L Ripper Teeth - Applications18, 20, 21, 22, 23 Seriesstyle description part no. rcv. disc. non stock used on

tooth, ripper, standard PM18HXtooth, ripper, sharp PM18SSHX N.S.tooth, ripper, tiger PMT18flex pin PM18Ptooth, standard, rock PM20HXR N.S.tooth, standard, PM20HXStooth, tiger PMT20 N.S.tooth, ripper, standard PM21HXtooth, ripper, standard PM22HXflex pin PM21/22adpt., nose, W-O ripper PM23RWN

H&L - Specifications


T standard T2A 4-1/4" 1-3/4" 1-1/16" 1-1/16" 1.1T long rock T2AR 4-5/16" 1-3/4" 1-1/16" 1-5/16" 1.22 adapter T716X2A 1" 4" 30° 1.5T standard PMT3C 4-3/4" 2-1/4" 1-9/16" 1-11/16" 1.4T flare T3CF 4-15/16"T standard PM3CHXL

adpt., W-O, flush PML2520W2AHX 2.4adpt., W-O, flush, cast-in place PM1001-3CHX 3.9adpt., W-O, flush PM1002-3CHX 3.7


PM18TL 10-1/2" point 2-1/2" 3-1/4" 3.1

T rip standard PM18HX 10-5/9" 2-3/8" 2-1/2" 3-1/4" 14.7T rip sharp PM18SSHX 9" 2-5/8" 2-1/2" 3-1/4"

T rip tiger PMT18 10-1/2" point 2-1/2" 3-1/4" 14

T

Type 1 Type 2

Type 3



T fanggs d TF23D 6" 1-3/4" 1-1/2" 1-5/8" 3.6

T fanggs l TF23L 5-7/8" 1-3/4" 1-1/2" 1-5/8" 3.4

T standard T230 5-7/8" 2" 1-1/2" 1-5/8" 2.8T standard T230SP 5-7/8" 2" 1-1/2" 1-5/8" 2.9T standard T23 5-1/8" 2-1/4" 1-1/2" 1-5/8" 2T tiger TT230 6-3/4" 3/16" 1-1/2" 1-5/8" 3.2T twin tiger T230WT 6-5/8" 3" 1-1/2" 1-5/8" 3.7T tiger h-d TT230HD 6-3/16" 3/8" 1-1/2" 1-5/8" 3.2T flare T230F 5-3/8" 4-3/4" 1-1/2" 1-5/8" 3.7T flare PM23HXFT star T230ST 6-3/8" 2" 1-1/2" 1-5/8" 2.6T long rock T23R 5-7/16" 2-1/4" 1-1/2" 1-5/8" 2.4T flare PM23HXF 5-1/4" 4-3/8" 1-1/2" 1-5/8" 3.2- adapter PM230010 3-3/8" 1-1/16" 2" 23° 4- adapter PM2300FL 2-7/8" 3/4" 23° 3.8

adpt., W-O, long leg on bttm. PMD834-23HX 3.1adpt. nose, W-O PM23WN 1.7adpt., W-O, .875" lip PM2740AW-23HX 3.4adpt., W-O, .75" lip PM2740MW-23HX 4.312" lip blade, w/(3) PM12M480-12AHX 3118" lip blade, w/4 noses PM18M480-12AHX 43.724" lip blade, w/5 noses PM24M480-12AHX 59

- adapter T417X230 3-5/8" 11/16" 1-3/4" 27° 3.7- adapter T728X230 3/4" 4-1/16" 25° 3.1- adapter U43792 3" 13/16" 1-1/2" 23° 3.5


24 Series

style description part no. a b c d lbs.T standard T240 6-3/4" 2-1/4" 1-9/16" 2-1/8" 4.5T standard PM24HD 6-3/8" 2-3/8" 1-9/16" 2-1/8" 3.6T standard PM24R 6-1/2" 2-3/8" 1-9/16" 2-1/8" 3.3T tiger TT240 7-1/2" 2-1/4" 1-9/16" 2-1/18" 4T twin tiger T240WT 7-1/2" 2-1/8" 1-9/16" 2-1/8" 5.1T long PM24SPHX 7-1/2" 2-1/4" 1-3/5" 2-1/8" 4.3T sharp PM24HXSS 6-4/5" 2-1/4" 1-3/5" 2-1/8" 3.5T star PMS240 7-5/8" point 1-3/5" 2-1/8" 4.22 adapter T427X240 3-3/4" 1-1/8" 2" 23° 4.8T star PMS240

pin PM24PBHXtooth, flare, 4" tip PM 24HXF 4.5adpt., W-O, misc. PM 809-24HX 8.8adpt., W-O, 1.25" lip PM 2740-24HX 7.4adpt. Nose, W-O PM 24WN 4


T fanggs d TF252 7-1/2" 2-1/2" 2-1/16" 2-1/8" 8.8T standard T252 6-7/8" 2-7/8" 2-1/16" 2-1/8" 6.7T standard PM251HXT twin tiger PM250TW 7-9/16" 3-9/16" 2-1/16" 2-1/8" 6.8T flare T252F 6-3/4" 5-3/4" 2-1/16" 2-1/8" 5.5

T star T252ST 8-1/4" 1-1/8" 2-1/16" 2-1/8" 6.1

T long PM251HX 7-1/3" 2-7/8" 2" 2-1/8" 5.22 adapter PM2500150 3" 1-3/4" 2" 23° 83 adapter T440X252 3" 1-9/16" 2" 23° 7.3

adpt., W-O, long leg on bttm. PM 855-252HX 14adpt., W-O, 1.25" lip PM 2740AW-252HX 7.5adpt., W-O, 1.625" lip PM 2740FW-252HX 7.5adpt., W-O, long leg on bttm. PM 3000W-252HX 9.2adpt., B-O, (case 850/1150B) PM L4079-252HX 12


T standard PM26HX 8-1/3" 2-7/8" 2" 2-4/5" 8.5T tiger PMT26 9-4/5" point 2" 2-4/5" 8.7T standard T260 2" 2-4/5"T standard PM26HX 2" 2-4/5"T tiger PMT26 2" 2-4/5"

oversize pin PM25126PDpin T25P


T standard T271 7" 2-1/8" 2-7/8" 2-1/8" 7.9

H&L - SpecificationsT standard PM27 7-1/2" 3-5/8" 2-7/8" 2-1/8" 8T standard PM271HX 7.63 3.69 2.88 2.13 8T flare PM27HXF 7" 7" 2-7/8" 2-1/8" 8T long PM27HXL 9" 3-3/4" 2-7/8" 2-1/8" 9.6

T tiger PMT27 9-1/2" Point 2-7/8" 2-1/8" 9.5T twin tiger PM27WT 9" 4" 2-7/8" 2-1/8" 10.32 adapter PM2700150 7-7/8" 1-11/16" 3" 23° 20

adpt., W-O, long leg on bttm. PM 3000W-27HX 13.1

H & L Ripper Teeth - Specifications


tooth, ripper, standard PM18HXtooth, ripper, sharp PM18SSHXtooth, ripper, tiger PMT18


tooth, standard, rock PM20HXRtooth, standard, PM20HXStooth, tiger PMT20


tooth, ripper, standard PM21HX


tooth, ripper, standard PM22HX


adpt., nose, W-O ripper PM 23RWN

Replacements for H & L Hardware

H & L14


T23P23 Series

T24P24 Series

TF23P23 Series Fanggs

T25P25 Series

TF25P25 Series Fanggs

T27P27 Series


Ripper and Scarifier Teeth

Ripper/Scarifier and Miscellaneous1

John Deere offers a selection of both centerline and penetration-style ripper teeth.

Remember these basic concepts:

1. Longer teeth offer more wearable material.

2. Shorter tips provide more strength.

Generally, use a long centerline tooth because it provides good penetration and more wearablematerial. If better initial penetration is needed, use the penetration-style tooth.


Rippers/Scarifiers John Deere Scarifier Motor Graders


-A- -B- -C-Series Tooth Part No. Length Width Point

Standard T1L 6″ 1-9/16″ 3/16″Fabricated 1.8 lb.

Crimp-On Shank T114792 JD: 570, 570A, 570B, 670B, 672B, 760, 760A, 770A,770B, 772A, 772B


Standard U15517 5-7/8″ 2-1/8″ 3/8″Cast 3.1 lb.

Pin 34M7070 Shank T66192 (34M7070) JD: 450G, 550G, 670, 670A, 670B, 672A,672B, 770, 770A, 770B, 772A, 772B

Pin U15522 Shank T75520 (U15522) JD: 350, 350B, 350C, 450, 450B, 450C,455D, 455E, 555, 555A, 555B


Standard T2D5572 7-3/8″ 1-7/8″ 3/16″Shank T114792 JD: 570, 570A, 570B, 670A, 670B, 672A, 672B, 770A,

770B, 772A, 772B


Rippers/Scarifiers John Deere Scarifier Motor Graders (Continued)



Standard T260 7-1/4″ 3″ 1/4″Fabricated 9.0 lb.

Pin T25P Shank T44319 JD: 670, 670A, 670B, 672A, 672B, 770, 770A, 770B,772A, 772B


Rippers/Scarifiers Ripper Teeth


-A- -B- -C- Pocket PocketSeries Tooth Part No. Ref. Length Width Point Width Height

25 Series EX25R12 12″ 2″ 1/4″ 2-11/16″ 3-3/16″Cast 10.8 lb.

Pin EX25RPG 2 Deere: Misc.Bushing EX25RBG

Intermediate PM9W2452 15-1/8″ 3-1/2″ 3/8″ 3-3/8″ 4-7/8″CenterlineTop PM4T2479 1 Cat: D8, D8K, D8L, D8N, D8R, D9, D9H, D9N, D9RBottom PM6J8811

Intermediate PM7J3310Top PM4J2479 1 Cat: D7, D8, D9Bottom PM6J8811

Long/Penetration T6Y0309 11-1/8″ 2″ 3/8″ 2-1/4″ 3-3/8″Pin T9W2668 1 T149204 (Shank) JD: 670B, 672B, 770B, 772BWasher T8E6359 PM9J6586 (Shank) Cat: 4, 5, 6, 7, 12, 14, 16, 130,

140, 931, 941, 951, 955, 963, 973, 977, 983, D3, D4,D8, D8L, D8N, D9, D9L, D9N, D10, D10N, D10R,D11N, D11R

Short PM9W2451 13-1/8″ 3″ 7/16″ 3-1/4″ 4-7/8″Top PM4T2479 1 Cat: D8, D8K, D8L, D8N, D8R, D9, D9N, D92, D94Bottom PM6J8811

Long T6Y0359 14-1/2″ 2-1/4″ 7/16″ 2-3/4″ 4-7/16″Pin T8E6358 Pin T9W2668 1 Cat: 4, 5, 6, 7, 12, 14, 16, 130, 140, 931, 941, 951,Washer T8E6359 955, 963, 973, 977, 983, D3, D8, D8L, D8N, D9, D9L,

D9N, D10, D10N, D10R, D11N, D11R

Intermediate PM4T5452PenetrationPin PM4T2479 1 Cat: D8, D8L, D9

Intermediate PM4T5502PenetrationPin PM3G0500 1 Cat: D9L, D10, D10N, D11

Penetration PM9J4259Pin PM8E6258 1 (No Shank Available) Cat: 943, 953Retainer PM8E6259



Rippers/Scarifiers Ripper Teeth (Continued)


-A- -B- -C-Series Tooth Part No. Ref. Length Width Point

Penetration PM4T5501Pin PM3G0500 1 (No Shank Available) Cat: D9L, D10, D10N, D11

Long PM1U3202Pin PM8E6208 (No Shank Available) Cat: 931, D3Retainer PM8E6209

Short PM1U3251(No Shank Available) Cat: 943, 953


John Deere Ripper Shanks


Part No. Description A B C D E F G Wt. (lb.)T75220 Scarifier - 40˚ 19-1/2″ 3-5/8″ 1″ 7/8″ 1″ 1″ 3/4″ 15.4

T66192 Scarifier - 28˚ 19-1/2″ 3-5/8″ 1″ 7/8″ 1″ 1″ 3/4″ 17.5

Part No. Description A B C D E Wt. (lb.)T149204 Shank 24-1/2″ 5-1/2″ 2-1/4″ 4-13/64″ 7″ 88.4

Part No. Description A B C D E Wt. (lb.)T44319 Shank, Ripper 28-29/32″ 5″ 2″ 2-1/2″ 9″ 75.3

Part No. Description A B C D E F G Wt. (lb.)T114792 Shank 19″ 3″ 1″ 2-7/16″ 1″ 3/4″ 3/4″ 14.7


Miscellaneous Replacements ADCO, Bofors, Case, Fiat-Allis, Ford, Komatsu


Part No. Description Pin / Description

Bofors

PM3031537 Tooth PM6254677 (Lock)

PM3031539 Tooth PM6254682 (Lock)

Case

PMD48212 Adapter, Weld-On 23 Series

PMD49586 Adapter, Bolt-On 23 Series

PMD49940 Adapter, Bolt-On 25 Series

Fiat-Allis

PM20853 Standard Tooth PM20853P (Pin)

Komatsu

PM2027012130 Standard Tooth PM0924402496




PM27 Fabricated Tooth T27P



-A- -B- -C- Pocket PocketSeries Tooth Part No. Ref. Length Width Point Width Height

100 Series T100C 6-3/16″ 3-3/16″ 1/2″ 1-5/8″ 1-5/8″Cast 3.4 lb.

Pin TF13P (Center) 1 Competitive: Backhoes with ADCO buckets.

100 Series T100 6-3/16″ 1/2″ 11/16″ 1-5/8″ 1-5/8″Cast 3.1 lb.

Pin TF13P (Interchangeable 2 Competitive: Backhoes with ADCO buckets.right/left)

Caterpillar Compactor Replacement PartsDirt Rock Rock Cleaner

Model Tamping Tamping Base Cleaner Cleaner BarFoot Foot (riser) Bar Bar Retainer

834, 835 PM8K9171* PM4S7928 PM4S7928 PM3S3225824B, 825B, PM7K2939*** PM7K2939*** PM3S3228 PM3S3228 PM3S3225 825G, 834, 835825C, 825G PM8K9171* PM3S3228 PM3S3225825C, 825G PM2V6628 PM4V0668 PM5V4311#815B PM2V7053 PM7K6908 PM5V4311#815, 815F PM8K9189** PM4V3851 PM7K6908 PM4S7928 PM3S3225* Bolt-on requires (2) 7/8" X 2-1/2" bolt, (2) 7/8" nut, and (4) PM4D6419 washer

** Bolt-on requires (2) 5/8" X 2-1/2" bolt, (2) 5/8" nut, and (4) PM5S0581 washer

*** Pin on foot

# Finger shank, uses replaceable tip T3G8250, requires T9J2258 pin, T3G9609 retainer

Your bucket tooth - Plasterer Equipment Company Deere Bucket Tooth... · Your bucket tooth...

Documents

Transcript of Your bucket tooth - Plasterer Equipment Company Deere Bucket Tooth... · Your bucket tooth...