Yale SIMPLICITY MORTICE LOCK MOUNTING INSTRUCTIONS 2 … Down… · Insert lock in mortice with...
2
P/No. YSL-5121 04/18 RIGHT - HAND DOOR LEFT - HAND DOOR OUTSIDE DOOR OPENING IN OUTSIDE DOOR OPENING OUT OUTSIDE DOOR OPENING OUT OUTSIDE DOOR OPENING IN 1 4 2 SETTING LOCK STATUS SETTING LOCK STATUS HAND OF DOOR ACCORDING TO ENGLISH PRACTICE Determine hand of lock required from hand of door chart above. Yale Simplicity Series Mortice Locks are mounted in accordance with these instructions. Locks may or may not have cylinders, lever handles or turn knob. Disregard instructions referring to the features not required. Important : Before drilling door, ensure correct hand is being installed. NOTE: CASE DOES NOT need to be opened, to change HAND or FUNCTION of LOCK. HANDING OF LOCK Determine hand of lock required from above hand of door chart. Rotate bolt head to suit latching direction. Ensure lock is in UNLOCKED position. To UNLOCK (if required), using a small screwdriver, lever out Cylinder Hole Plug where fitted and lift snib using the screwdriver. SNIB Rotation of the Snib hands the lock. With snib in unlocked position, use a cylinder pin to rotate the snib if required. ESCAPE Locks The hole on the snib indicates the side lockable. For left hand door the hole will be visible from the left of the lock. For right hand door the hole will be visible from the back of the lock. The escape side will have no holes on the snib. LOCKABLE LOCKABLE ESCAPE ESCAPE LEFT HAND DOOR ESCAPE TURN KNOB ADAPTORS UNLOCKED (Snib up) LOCKED (Snib down) Yale ® MOUNTING INSTRUCTIONS SIMPLICITY MORTICE LOCK ESCAPE RIGHT HAND DOOR STANDARD TURN KNOB ADAPTORS 3 ANTI-LOCKOUT TURN KNOB ADAPTORS 4 Establish which side the adaptor is to be located, lever out Cylinder hole plug where fitted. PUT LOCK IN LOCKED POSITION, as shown in Step 1. Align Adaptor cam so that it points up towards the top of the lock front plat, and Place retainer pin through front plate to retain adaptor to lock. Ensure pin is flush with front plate. L L YOKE TURN KNOB CAM Anti-lockout is achievable via an anti-lockout adaptor. Ensure the lock is unlocked and that the leg of the adaptor is installed behind the bolt frame. The adaptors are handed. Ensure that the correct adaptor is installed. 1 HOLE - 20mm DIA. FOR SPINDLE 1 HOLE - 20mm DIA. FOR SPINDLE 2 HOLES - 20mm DIA. SLOT FOR CYLINDER 2 HOLES - 20mm DIA. SLOT FOR CYLINDER 2 HOLES - Ø6.5mm 2 HOLES - Ø6.5mm ENSURE LOCK IS REMOVED FROM MORTICE BEFORE DRILLING HOLES. TO PREVENT POSSIBLE DAMAGE TO DOOR FACE DO NOT DRILL RIGHT THROUGH DOOR. ENSURE LOCK IS REMOVED FROM MORTICE BEFORE DRILLING HOLES. TO PREVENT POSSIBLE DAMAGE TO DOOR FACE DO NOT DRILL RIGHT THROUGH DOOR. Adaptor leg insert into the lock. (Look from the other side to check engagement with snib) 1 HOLE - 20mm DIA. FOR TURN 1 HOLE - 20mm DIA. FOR TURN
Transcript of Yale SIMPLICITY MORTICE LOCK MOUNTING INSTRUCTIONS 2 … Down… · Insert lock in mortice with...
P/N
o. Y
SL-5
121
04
/18
RIGHT - HAND DOOR LEFT - HAND DOOR
OUTSIDE DOOR OPENING
IN
OUTSIDE DOOR OPENING
OUT
OUTSIDE DOOR OPENING
OUT
OUTSIDE DOOR OPENING
IN
1
4
2
SETTING LOCK STATUS
SETTING LOCK STATUS
HAND OF DOOR ACCORDING TO ENGLISH PRACTICE
Determine hand of lock required from hand of door chart above. Yale Simplicity Series Mortice Locks are mounted in accordance with these instructions. Locks may or may not have cylinders, lever handles or turn knob. Disregard instructions referring to the features not required. Important : Before drilling door, ensure correct hand is being installed. NOTE: CASE DOES NOT need to be opened, to change HAND or FUNCTION of LOCK. HANDING OF LOCK Determine hand of lock required from above hand of door chart. Rotate bolt head to suit latching direction. Ensure lock is in UNLOCKED position.
To UNLOCK (if required), using a small screwdriver, lever out Cylinder Hole Plug where fitted and lift snib using the screwdriver.
SNIBRotation of the Snib hands the lock. With snib in unlocked position, use a cylinder pin to rotate the snib if required.
ESCAPE Locks The hole on the snib indicates the side lockable.
For left hand door the hole will be visible from the left of the lock. For right hand door the hole will be visible from the back of the lock. The escape side will have no holes on the snib.
Establish which side the adaptor is to be located, lever out Cylinder hole plug where fitted. PUT LOCK IN LOCKED POSITION, as shown in Step 1. Insert Adaptor into lock body with TOP of Turn Knob Cam point away from front of lock body. Ensure Turn Knob Cam is engaged in yoke of snib as shown. Place retainer pin through front plate to retain adaptor to lock. Ensure pin is flush with front plate
LOCKABLE
LOCKABLE ESCAPE
ESCAPE LEFT HAND DOOR ESCAPE
TURN KNOB ADAPTORS
UNLOCKED(Snib up)
LOCKED(Snib down)
Yale®
MOUNTING INSTRUCTIONS SIMPLICITY MORTICE LOCK
ESCAPE RIGHT HAND DOOR
STANDARD TURN KNOB ADAPTORS3 ANTI-LOCKOUT TURN KNOB ADAPTORS4
Establish which side the adaptor is to be located, lever out Cylinder hole plug where fitted. PUT LOCK IN LOCKED POSITION, as shown in Step 1. Align Adaptor cam so that it points up towards the top of the lock front plat, and
Place retainer pin through front plate to retain adaptor to lock. Ensure pin is flush with front plate.
L
L
YOKE
TURN KNOB CAM
Anti-lockout is achievable via an anti-lockout adaptor. Ensure the lock is unlocked and that the leg of the adaptor is installed behind the bolt frame.
The adaptors are handed. Ensure that the correct adaptor is installed.
1 H
OLE
- 20
mm
DIA
.FO
R SP
IND
LE
1 H
OLE
- 20
mm
DIA
.FO
R SP
IND
LE
2 H
OLE
S - 2
0mm
DIA
.SL
OT
FOR
CYLI
ND
ER
2 H
OLE
S - 2
0mm
DIA
.SL
OT
FOR
CYLI
ND
ER
2 H
OLE
S - Ø
6.5m
m2
HO
LES
- Ø6.
5mm
ENSURE LOCK IS REMOVED FROM MORTICEBEFORE DRILLING HOLES.
TO PREVENT POSSIBLE DAMAGE TO DOOR FACEDO NOT DRILL RIGHT THROUGH DOOR.
ENSURE LOCK IS REMOVED FROM MORTICEBEFORE DRILLING HOLES.
TO PREVENT POSSIBLE DAMAGE TO DOOR FACEDO NOT DRILL RIGHT THROUGH DOOR.
Adaptor leg
insert into the lock. (Look from the other side to check engagement with snib)
1 H
OLE
- 20
mm
DIA
. FO
R TU
RN1
HO
LE -
20m
m D
IA.
FOR
TURN
65 DOOR PREPARATION DOOR PREPARATION
Establish height that lockset will be mounted on door and mark centreline of door thickness on door edge.Place Mortice Template on door and align centreline on template with centreline on door.Mark and drill mortice to suit mortice lock depth (90mm).
Ease out mortice cavity where necessary. Clean out mortice before inserting lock.Insert lock in mortice with Cover Plate on and scribe around Cover Plate for size of recess, ensuring that no foreign matter finds it way into the lock mechanism. Remove lock from mortice and chisel recess 4mm deep to receive both front and cover plate. Cover plate must be flush with edge of door.Ensure lock is removed from mortice cavity. Fold template along backset foldline. Align EDGE A with bottom of cover plate recess. Establish holes required tosuit lock function, mark hole centres accurately, drill and clean holes.Drill furniture holes as required.Fasten mortice lock into door using mounting screws provided.
87
Place lock in mortice and insert cylinder.Secure cylinder with retainer pin, ensuring pin is flush with front plate. Install Cover plate and secure with 2 M4 screws provided to lock body.
Strike
StrikeBox
Jamb
Mark out door frame for strike. Use strike and strike box as templates and then mortice door frame for strike. Screw strike and strike box to the door frame with two screws supplied with Spindles are supplied with the furniture.
Insert spindle(s) into lock, as required.Assemble furniture as required. Ensure furniture is not over-tightened.
LOCKS WITH TURNKNOBS
9 LOCKS WITH SPINDLES 10 MOUNTING STRIKE
ENSURE LOCK IS REM
OVED FRO
M M
ORTICE
HOLE 22mm DIAFOR SPINDLE
EDGE A
2 HOLES 20mm DIAFOR CYLINDER
60 mm Backset
Centreline
Mortice template
Door
TE
SK
CA
B m
m06
RO
OD
FO
EG
DE
GN
OLA
ENI
L DL
OF
ecit
roM
enil
ertn
eC
IMPORTANT - To prevent damage to the door face from drill "breakthrough", MARK BOTH SIDES OF DOOR & DRILL HOLES HALF WAY THROUGH EACH SIDE
LATCHNG OR LOCKING TURNKNOB
IMPORTANT :Attach spindle spring to rearof spindle before assembling
Cover plate
Cover plate
LOCKS AND CYLINDERSCylinder retainerpin
Cylinder assembly
LATCH BOLTCENTRE LINE
Timber frames - drill 2.5mm pilot holes and use 30mm long screws Metal frames - drill 4mm pilot holes and use 12mm long screws
Mark correct length of connecting bar as shown.
For locking turnknob, mark the connecting bar at the edge of the screw on themounting lock faceplate.
Cut connecting bar to length, remembering to remove the burr.
When lockset is in unlocked condition, turnknob to be vertical.
Screw position
Anti-rattle tab
PLEA
SE R
ECYCLE THIS PACK
AG
ING
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 ©2018The global leader in door opening solutions
To eliminate the rattle between the door and plate, bend the tab by small increments.
