Y Hello Kitty Planter - now small and medium size! · So, the thingiverse was missing a Hello Kitty...
3
Summary So, the thingiverse was missing a Hello Kitty themed planter, my gf wanted one, so i made one. The planter part is 62mm in diameter (2.44 inch) and 56mm in Height (2.2 inch), so it fits perfectly these mini flower things you get everywhere. Overall Height is 83mm (3.26 inch) (printing time around 7 hours @70mm/s) EDIT: I added a Version for bigger Plants, with smaller Walldimensions (the walls are 2mm thick on the small planters, but 1mm on the medium), and with a bigger diameter of roughly 100mm (3.95 inch)! Head is only slightly larger! Overall height is about 94mm (3.74 inch) ! (printing time around 10 hours @70mm/s) EDIT 2: i also added the bigger Version with the same wall thickness as the small one (2mm ~ 0,08inch)! Happy printing! Household > Home Decor pot plantpot planterpot planterspot planters planter hellokitty flowerpot eponra Hello Kitty Planter - now small and medium size! VIEW IN BROWSER updated 9. 11. 2019 | published 9. 11. 2019 3D MODEL ONLY
Transcript of Y Hello Kitty Planter - now small and medium size! · So, the thingiverse was missing a Hello Kitty...
Summary
So, the thingiverse was missing a Hello Kitty themed planter, my gfwanted one, so i made one.
The planter part is 62mm in diameter (2.44 inch) and 56mm in Height (2.2inch), soit fits perfectly these mini flower things you get everywhere.Overall Height is 83mm (3.26 inch)(printing time around 7 hours @70mm/s)
EDIT: I added a Version for bigger Plants, with smaller Walldimensions (thewalls are 2mm thick on the small planters, but 1mm on the medium), andwith a bigger diameter of roughly 100mm (3.95 inch)!Head is only slightly larger! Overall height is about 94mm (3.74 inch) !(printing time around 10 hours @70mm/s)
EDIT 2: i also added the bigger Version with the same wall thickness as thesmall one (2mm ~ 0,08inch)!
Happy printing!
Household > Home Decor
pot plantpot planterpot planterspot planters planter
hellokitty flowerpot
eponra
Hello Kitty Planter -now small andmedium size!
VIEW IN BROWSER
updated 9. 11. 2019 | published 9. 11. 2019
3D M
ODEL
ONLY
Model Files (.stl, .3mf, .obj, .amf) DOWNLOAD ALL FILES
Category: Outdoor & Garden Print Settings
Printer: Tevo Tornado
Rafts: No
Supports: Yes
Resolution: 0.2
Infill: 15%
Filament: Owl Filament PLA pinkNotes:
Printing time around 7 hours @70mmm/s and 0.2 layer height for the smallone,around 10 hours @70mm/s for the bigger one!
• 5 Walls• 4 Bottom Layers Also for best Supports use: • Support Placement: Everywhere • Support Overhang Angle: 60°• Support Pattern: Lines• Support Density: 15%• Support Z Distance: 0.1• Enable Support Interface: V• Support Interface Thickness: 1mm• Support Interface Density: 100%
How I Designed This
• Took a sitting Hello Kitty • cut off the head in tinkercad• enlarged that a lot• created a fitting container for my plant• copied that container and used it to cut out the form on the back of
the hello kitty head• then combined the two things.
309.1 KBupdated 9. 11. 2019
317.6 KBupdated 9. 11. 2019
302.8 KBupdated 9. 11. 2019
Find source .stl files on Thingiverse.com
The Author has not uploaded any G-codes.Try to search in User G-codes section or generate and upload yourown.
License
This work is licensed under a Creative Commons (4.0 International License)
Attribution—Noncommercial—Share Alike
✖ | Sharing without ATTRIBUTION ✔ | Remix Culture allowed ✖ | Commercial Use ✖ | Free Cultural Works ✖ | Meets Open Definition
hello_kitty_planter.stl
hello_kitty_planter_100mm.stl
hello_kitty_planter_100mm_2mm_walls.stl
