XV-Z9000U Operation Manual - ProjectorCentral are two important reasons for prompt warranty...

E-1

Impo

rtant

Info

rmat

ion

IMPORTANTFor your assistance in reporting the loss or theft of yourProjector, please record the Serial Number located onthe bottom of the projector and retain this information.Before recycling the packaging, please be sure thatyou have checked the contents of the carton thoroughlyagainst the list of “Supplied Accessories” on page 12.

Before using the projector, please read this operation manual carefully.

OPERATION MANUAL ENGLISH

Model No.: XV-Z9000U

Serial No.:

There are two important reasons for prompt warranty registration of your new SHARP Projector, usingthe REGISTRATION CARD packed with the projector.1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and laborwarranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACTTo ensure that you will promptly receive any safety notification of inspection, modification, orrecall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASEREAD CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE. U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especiallycareful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment notexpressly approved by the manufacturer could void the user’s authority to operate this equip-ment.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTIONRISK OF ELECTRIC SHOCK.DO NOT REMOVE SCREWSEXCEPT SPECIFIED USER

SERVICE SCREW.

The lightning flash with arrowhead symbol,within an equilateral triangle, is intended toalert the user to the presence of uninsulated“dangerous voltage” within the product’senclosure that may be of sufficient magnitudeto constitute a risk or electric shock topersons.

The exclamation point within a triangle isintended to alert the user to the presence ofimportant operating and maintenance(servicing) instructions in the literatureaccompanying the product.

PRODUCT DISPOSALThis product utilizes tin-lead solder, and high intensity discharge lamp (HID lamp) containing a small amount ofmercury. Disposal of these materials may be regulated due to environmental considerations. For disposal orrecycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org .

EN

GL

ISH

U.S.A. ONLY

E-2

Important

Information

EN

GL

ISH

WARNING:The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. Duringnormal operation, when turning the power off always use the OFF button on the projector or on the remotecontrol. Ensure the cooling fan has stopped before disconnecting the power cord.DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWERCORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

Declaration of Conformity

SHARP PROJECTOR, MODEL XV-Z9000U

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

Responsible Party:

SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430TEL: 1-800-BE-SHARP (1-800-237-4277)

INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energyand, if not installed and used in accordance with the operation manual, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

Caution Concerning the Lamp ReplacementThere is potential glass particles hazard if the lamp ruptures.

LAMP REPLACEMENT

BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMPUNIT TYPE BQC-XVZ9000/1 ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE.TURN OFF LAMP BEFORE SERVICING.MEDIUM PRESSURE LAMP : RISK OF EXPLOSION.POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE.SEE OPERATION MANUAL.

REMPLACEMENT DE LA LAMPE.

USER SERVICE SCREWSVIS POUR ENTRETIEN PAR L’UTILISATEUR

PRECAUTIONS A OBSERVER LORS DU

DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEUREAVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XVZ9000/1.RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIELDE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.

CAUTION

U.S.A. ONLY

WARNING:Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments.Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompilethe contents thereof.

E-3

Impo

rtant

Info

rmat

ion IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure yourpersonal safety. However IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In ordernot to defeat the safeguards incorporated into this Projector, observe the following basic rules for its installation, use andservicing. For your own protection and reliable usage of your Projector, please be sure to read these “IMPORTANTSAFEGUARDS” carefully before use.

1. Read InstructionsAll the safety and operating instructions should be readbefore the product is operated.

2. Retain InstructionsThe safety and operating instructions should be retainedfor future reference.

3. Heed WarningsAll warnings on the product and in the operatinginstructions should be adhered to.

4. Follow InstructionsAll operating and use instructions should be followed.

5. CleaningUnplug this product from the wall outlet before cleaning.Do not use liquid cleaners or aerosol cleaners. Use adamp cloth for cleaning.

6. AttachmentsDo not use attachments not recommended by the productmanufacturer as they may cause hazards.

7. Water and MoistureDo not use this product near water – for example, near abathtub, wash bowl, kitchen sink, or laundry tub; in a wetbasement; or near a swimming pool; and the like.

8. AccessoriesDo not place this product on an unstable cart, stand,tripod, bracket, or table. The product may fall, causingserious injury to a child or adult, and serious damage tothe product. Use only with a cart, stand, tripod, bracket,or table recommended by the manufacturer, or sold withthe product. Any mounting of the product should followthe manufacturer’s instructions, and should use amounting accessory recommended by the manufacturer.

9. TransportationA product and cart combinationshould be moved with care. Quickstops, excessive force, anduneven surfaces may cause theproduct and cart combination tooverturn.

10. VentilationSlots and openings in the cabinet are provided forventilation to ensure reliable operation of the product andto protect it from overheating. The openings should neverbe covered or blocked by placing the product on a bed,sofa, rug, or other similar surface. This product shouldnot be placed in a built-in installation such as a bookcaseor rack unless proper ventilation is provided or themanufacturer’s instructions have been adhered to.

11. Power SourcesThis product should be operated only from the type ofpower source indicated on the marking label. If you arenot sure of the type of power supply to your home, consultyour product dealer or local power company. For productsintended to operate from battery power, or other sources,refer to the operating instructions.

12. Grounding or PolarizationThis product is equipped with a three-wire grounding-typeplug, a plug having a third (grounding) pin. This plug willonly fit into a grounding-type power outlet. This is a safetyfeature. If you are unable to insert the plug into the outlet,contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the grounding-typeplug.

13. Power-Cord ProtectionPower-supply cords should be routed so that they are notlikely to be walked on or pinched by items placed uponor against them, paying particular attention to cords atplugs, convenience receptacles, and the point where theyexit from the product.

14. LightningFor added protection for this product during a lightningstorm, or when it is left unattended and unused for longperiods of time, unplug it from the wall outlet anddisconnect the power cord. This will prevent damage tothe product due to lightning and power-line surges.

15. OverloadingDo not overload wall outlets, extension cords, or integralconvenience receptacles as this can result in a risk of fireor electric shock.

16. Object and Liquid EntryNever push objects of any kind into this product throughopenings as they may touch dangerous voltage points orshort-out parts that could result in a fire or electric shock.Never spill liquid of any kind on the product.

17. ServicingDo not attempt to service this product yourself as openingor removing covers may expose you to dangerous voltageor other hazards. Refer all servicing to qualified servicepersonnel.

18. Damage Requiring ServiceUnplug this product from the wall outlet and refer servicingto qualified service personnel under the followingconditions:

a. If the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into

the product.c. If the product has been exposed to rain or water.d. If the product does not operate normally by following

the operating instructions. Adjust only those controlsthat are covered by the operating instructions, as animproper adjustment of other controls may result indamage and will often require extensive work by aqualified technician to restore the product to normaloperation.

e. If the product has been dropped or damaged in anyway.

f. If the product exhibits a distinct change inperformance, this indicates a need for service.

19. Replacement PartsWhen replacement parts are required, be sure the servicetechnician has used replacement parts specified by themanufacturer or with the same characteristics as theoriginal part. Unauthorized substitutions may result in fire,electric shock, or other hazards.

20. Safety CheckUpon completion of any service or repairs to this product,ask the service technician to perform safety checks todetermine that the product is in proper operatingcondition.

21. Wall or Ceiling MountingThis product should be mounted to a wall or ceiling onlyas recommended by the manufacturer.

22. HeatThis product should be situated away from heat sourcessuch as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.

E-4

Important

Information

IMPORTANT SAFEGUARDS

95˚F(35˚C)

41˚F(5˚C)

CAUTIONPRECAUCIÓNPRÉCAUTION

BQC-XVZ9000/1

Caution Concerning the Lamp UnitThere is a potential hazard of glass particles if the lamp ruptures. In case oflamp rupture, contact your nearest Authorized SharpVision Service Centeror Dealer for a replacement.See “Replacing the Lamp” on page 47.

Cautions Concerning the Setup of the ProjectorFor minimal servicing and to maintain high image quality, SHARP recommendsthat this projector be installed in an area free from humidity, dust and cigarettesmoke. When the projector is subjected to these environments, the lens andpart of filter must be cleaned more often than usual. As long as the projectoris properly maintained in this manner, use in these environments will not reducethe overall operation life. Please note that all internal cleaning must beperformed by an Authorized SharpVision Service Center or Dealer.• Do not expose the projector to extreme heat or cold.

Operating temperature: 41°F to 95°F (+5°C to 35°C)Storage temperature: –4°F to 140°F (–20°C to +60°C)

Notes on Operation• The exhaust ventilative hole, the lamp cage cover and adjacent areas may

get extremely hot during projector operation. To prevent injury, do not touchthese areas until they have sufficiently cooled down.

• Allow at least 1 foot (30 cm) of space between the exhaust ventilative holeand the nearest wall or obstruction.

• If the cooling fan becomes obstructed, a protection device will automaticallyturn off the projector lamp. This does not indicate a malfunction. Removethe projector power cord from the wall outlet and wait at least 10 minutes.Then turn on the power by plugging the power cord back in. This will returnthe projector to the normal operating condition.

LAMP REPLACEMENT

BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMPUNIT TYPE BQC-XVZ9000/1 ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE.TURN OFF LAMP BEFORE SERVICING.MEDIUM PRESSURE LAMP : RISK OF EXPLOSION.POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE.SEE OPERATION MANUAL.

REMPLACEMENT DE LA LAMPE.

USER SERVICE SCREWSVIS POUR ENTRETIEN PAR L’UTILISATEUR

PRECAUTIONS A OBSERVER LORS DU

DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEUREAVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XVZ9000/1.RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIELDE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE.A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.

CAUTION

This label is pasted the side of the projector.

E-5

Impo

rtant

Info

rmat

ion IMPORTANT SAFEGUARDS

Temperature Monitor FunctionIf the projector starts to overheat due to setup problems or a dirty air filter,“TEMP.” and “ ” will flash in the lower-left corner of the picture. If thetemperature continues to rise, the lamp will turn off, the TEMPERATUREWARNING indicator on the projector will flash, and after a 90-second cooling-off period the power will shut off. Refer to “Lamp/Maintenance Indicators” onpage 45, for details.

• The cooling fan regulates the internal temperature, and its performance isautomatically controlled. The sound of the fan may change during projectoroperation due to changes in the fan speed.

Lamp Monitor FunctionWhen the projector is turned on after the lamp has been used for 1,900 hours,“LAMP” and “ ” will flash in the lower-left corner of the picture to advise youto replace the lamp. See page 47 for lamp replacement. If the lamp has beenused for 2,000 hours, the projector power will automatically turn off and theprojector will enter standby mode. Refer to “Lamp/Maintenance Indicators”on page 45, for details.

Using the Terminal Cover• When ceiling-mounting the projector, attach the terminal cover (supplied)

to hide the connecting cables.• Use the terminal cover to hide the connecting cables when the projector is

used on a desktop or high mounted.

1 Install the terminal cover using the two attached clips.

2 Attach the terminal cover by aligning with the tab on the projector.

PUSH

1

1

1

2

2

E-6

Important

Information

Outstanding Features

1. Wide DMD™* (Digital Micromirror Device) ChipThe DMD Chip allows for a higher contrast image. Also, as it has an aspect ratio of 16:9, it is possible toview, in the best possible picture frame, software recorded on 16:9 from DVD or DTV.

* Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.

2. Full 720P ResolutionThe high resolution panel of 921,600 pixels (1280 × 720 dots) allows for viewing high image quality just asthe original as well as HDTV 720P signals.

3. Low Noise DesignA new optical engine has been developed for this product resulting in minimized fan noise for undisturbedviewing.

4. For Use with DTVAllows projection of DTV images and 16:9 wide-screen images when connected to a DTV decoder orsimilar video system.

5. New Progressive Mode and Film ModeOptimizes the image by converting the interlaced signal to the progressive. Useful for displaying slow-moving images or still images. Three modes are available.

6. Advanced Video CircuitryProvides high quality images with minimal dot crawl and cross color noise.

7. Easy-to-use Graphical User Interface (GUI)A multi-color menu system, which allows for simple image adjustments.

8. Color Temperature AdjustmentThe function can be used to adjust the color temperature to suit the type of image input to the projector.

9. Gamma Correction FunctionThe gamma value setting can be adjusted according to the input source for optimal image contrast.

10. Brightness Switchover FunctionFunction with toggle switch to control the quantity of projected light. Select “NORMAL” or “BRIGHT” todecrease or increase brightness, power consumption and fan noise.

11. Component Video InputUtilizes a component video input signal (Y, PB, PR). The video signal is input as separate components toprovide superior color and image quality.

12. Direct Computer CompatibilityA multi-scan RGB input accepts signals from VGA (640 dots × 480 lines) and Macintosh (from 13" compatiblecomputers) without the need for any additional hardware.

For SHARP Assistance (U.S.A. only)If you encounter any problems during setup or operation of this projector, first take a look at the section“Troubleshooting” on page 50. If this operation manual does not answer your question, please call toll free1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an e-mail at [email protected] World Wide Web address is http://www.sharp-usa.com/ .

E-7

Impo

rtant

Info

rmat

ion How to Access the PDF Operation Manuals of SharpVision Manager

PDF operation manuals of supplied GAMMA control software “SharpVision Manager” in several languages areincluded in the CD-ROM. To utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windowsor Macintosh). If you have not installed Acrobat Reader yet, you can download it from the Internet (http://www.adobe.com) or install it from the CD-ROM.

To Install Acrobat Reader from the CD-ROM

For other operating systems:Please download Acrobat Reader from the Internet (http://www.adobe.com).

For other languages:If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download theappropriate version from the Internet.

Accessing the PDF Manuals

For Windows:1 Insert the CD-ROM in the CD-ROM drive.2 Double click on the “My Computer” icon.3 Double click on the “CD-ROM” drive.4 Double click on the “acrobat” folder.5 Double click on the “windows” folder.6 Double click on the desired installation program

and follow the instructions on the screen.

For Macintosh:1 Insert the CD-ROM in the CD-ROM drive.2 Double click on the “CD-ROM” icon.3 Double click on the “acrobat” folder.4 Double click on the “mac” folder.5 Double click on the desired installation program

and follow the instructions on the screen.

For Windows:1 Insert the CD-ROM in the CD-ROM drive.2 Double click on the “My Computer” icon.3 Double click on the “CD-ROM” drive.4 Double click on the “MANUALS” folder.5 Double click on the “SVM_U” folder.6 Double click on the language (name of the folder)

that you want to view.7 Double click on the “SVM” pdf file to access the

SharpVision Manager manual.

For Macintosh:1 Insert the CD-ROM in the CD-ROM drive.2 Double click on the “CD-ROM” icon.3 Double click on the “MANUALS” folder.4 Double click on the “SVM_U” folder.5 Double click on the language (name of the folder)

that you want to view.6 Double click on the “SVM” pdf file to access the

SharpVision Manager manual.

• If the desired PDF file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desiredfile using the “File”, “Open” menu.

• See the “readme.txt” file on the CD-ROM for important information on the CD-ROM not included in this operation manual.

E-8

Important

Information

Contents

Important Information

IMPORTANT SAFEGUARDS ................... 3Outstanding Features ............................. 6How to Access the PDF Operation

Manuals ............................................... 7Contents ................................................... 8Part Names .............................................. 9Supplied Accessories ............................. 12

Connections ............................................ 13Power Supply ............................................ 13Connecting to Video Equipment ............... 13Connecting to a DVD Player and DTV

Decoder ............................................... 14Connecting to a Computer ........................ 15Operating the Remote Control .................. 16Using as a Wired Remote Control ............. 16Power ON/OFF .......................................... 17Zooming and Focusing ............................. 17

Setting Up the Screen ............................. 18Using the Adjustment Feet ........................ 18Using the Lens Shift .................................. 18Keystone Correction .................................. 19Adjusting the Projection Distance ............. 20

Image Projection ..................................... 22Rear Projection .......................................... 22Projection Using a Mirror ........................... 22Ceiling-mount Projection ........................... 22

Setup &Connections

Operation Buttons

Setup & Connections

Operation ButtonsBasic Operation

Maintenance &

TroubleshootingAppendix

Using the Operation Buttons ................. 23Selecting the Input Signal Source ............. 23Adjusting the Picture Aspect Ratio ............ 23Gamma Correction Function ..................... 25

Basic Operation

Using the GUI (Graphical UserInterface) Menu Screen...................... 26Basic Operations ....................................... 26

Maintenance &Troubleshooting

Lamp/Maintenance Indicators................ 45Lamp Maintenance .................................. 46

Confirming the Lamp Usage Time ............ 46Replacing the Lamp .................................. 47

Cleaning the Air Filters ........................... 49Using the Kensington Lock ....................... 49

Troubleshooting ...................................... 50For SHARP Assistance (U.S.A. only) ..... 50

Appendix

Connecting Pin Assignments ................ 51(RS-232C) Specifications and

Command Settings ............................ 52Wired Remote Control Terminal

Specifications ..................................... 55Computer Compatibility Chart ............... 56Dimensions .............................................. 57Specifications .......................................... 58Glossary ................................................... 59Index ......................................................... 60

Menu Bars ................................................. 27Adjusting the Picture ................................. 29Adjusting the Computer Images

(RGB menu only) ................................. 32Reducing Image Noise

(VIDEO menu only) .............................. 36Turning On/Off the On-screen Display ...... 37Setting the Video Signal

(VIDEO menu only) .............................. 37Theater Mode Functions............................ 38Selecting a Background Image................. 39Subtitle Setting .......................................... 40Selecting the Economy Mode ................... 41Selecting the Transmission Speed

(RS-232C) ............................................ 42Reversing/Inverting Projected Images ...... 43Selecting the On-screen Display

Language ............................................ 43Displaying the Adjustment Settings .......... 44

E-9

Impo

rtant

Info

rmat

ion Part Names

Projector

Numbers next to the part names refer to the main pages in this manual where the topic is explained.

Front and Top View

16

18

45

45

45

26

26

26

17

23

23

26

Focus ring

Remote control sensor

POWER indicator

4 Intake ventilative hole

LAMP REPLACEMENT indicator

TEMPERATURE WARNING indicator

ADJUSTMENT buttons(∂/ƒ/ß/©)

UNDO button

ENTER button

MENU button

RESIZE button

INPUT button

POWER buttons (ON/OFF)

Adjuster

Zoom knob

18Adjuster

12 Lens cap

18

17

17

Lens shift dial

Side and Rear View

E-10

Important

Information

Part Names

Projector

Numbers next to the part names refer to the main pages in this manual where the topic is explained.

Side and Rear View

14

13

1415

4

4

13

Intake ventilative hole

Exhaust ventilative hole

16Remote control sensor

16AC socket

DC 12 V 200 mAOUTPUT terminal

Intake ventilative hole4

15INPUT 5 COMPUTER-RGB port(15-pin Mini D-sub) INPUT 1 COMPONENT/

RGB terminals (RCA)

INPUT 2 COMPONENT/RGB terminals (RCA)

Wired remotecontrol jack

VIDEO INPUT 4 terminal (RCA)

13S-VIDEO INPUT 3 terminal(4-pin Mini DIN)

DC 12V OUTPUT

RS-232C port (9-pin D-sub)

E-11

Impo

rtant

Info

rmat

ion Part Names

Inserting the batteries

1 3Pull down the tab on thebattery cover andremove the covertowards the direction ofthe arrow.

2 Insert two AA sizebatteries, making surethe polarities match the and marks insidethe battery compartment.

Insert the lower tab ofthe battery cover intothe opening, and pressthe cover until it clicksin place.

Top View

Remote Control

BACKLIGHT button

17

23

38

25

35

26

26 26

26

23

23 23

23

23

30

19

16

POWER buttons (ON/OFF)

ENTER button

UNDO button

INPUT 1 button

INPUT 2 button

INPUT 4 button

THEATER MODE button RESIZE button

CLR TEMP buttons

MENU button

ADJUSTMENT buttons (∂/ƒ/ß/©)

INPUT 3 button

INPUT 5 button

AUTO SYNC button

GAMMA buttonKEYSTONE button

Front View

Top View

16

Remote control signal transmitter

Wired remote control jack

Battery coverBattery

compartment

Battery cover

E-12

Important

Information

Supplied Accessories

Power cordCACCU5013DE01

Remote controlRRMCG1657CESA

Two AA size batteries Terminal coverCCOVA1985CE01

Projector operation manualTINS-7416CEZZ

SharpVision Manager operation manualTINS-7418CEZZ

Lens capPCAPH1056CESA

CD-ROM(SharpVision Manager)UDSKA0047CEN1

E-13

Setu

p &

Con

nect

ions

Power Supply

Connecting the Power CordPlug the supplied power cord into the AC socket on the back of the projector.

Connections

Power cordCACCU5013DE01

CAUTION• Make sure the power cord is firmly connected into the AC socket.

• The projector will enter the stand-by mode after turning the power off and then re-plugging the power cord into the AC socket. However,if you turned off the power by disconnecting the power cord or because of a power failure, the projector will automatically turn on withoutpressing the POWER ON button.

1 Connect one end of the S-video cable (commerciallyavailable) to the INPUT 3 S-VIDEO terminal, or one endof the video cable (commercially available) to the INPUT4 VIDEO terminal on the projector.

2 Connect the other end of the S-video cable or the videocable to the S-video output or Video output terminal ofthe video source.

The S-video input terminal uses a video signal system wherethe picture is separated into a color and luminance signalto realize a higher-quality image.

• For higher quality video, you may use the S-video input terminal on theprojector. S-video cable is commercially available.

• If your video equipment does not have an S-video output terminal, usethe composite video output terminal.

Connecting to Video Equipment

Connecting a video source (VCR, laser disc player, DVD player or DTV decoder) using the INPUT 3S-VIDEO and INPUT 4 VIDEO terminals

You can connect your projector to a VCR, laser disc player, DVD player, DTV* decoder and other video equipment.* DTV is the umbrella term used to describe the new digital television system in the United States.

CAUTION• Make sure to turn both the projector and the video equipment off, before connecting.

• As this projector is not equipped with audio input terminals, commercially available audio equipment or your own equipment (such asspeakers or amplifiers) should be used.

E-14

Setup & Connections

1

2 To S-video output terminal

2 To video output terminal

1

Projector

VCR,Laser disc player,

DVD player orDTV decoder

Connecting to Video Equipment

Connecting to a DVD Player and DTV Decoder

*

*

2 To component outputterminals

1

Component cable(commercially available)

DVD playeror

DTV decoder

1 Connect each RCA connector of a component cable to the correspondingRCA INPUT 1 or 2 terminals on the projector.

2 Connect the other end of the cable to the corresponding terminals on a DVDplayer or DTV decoder.

When connecting this projector to a DVD player or DTV decoder, select“Component” for “Signal Type” on the GUI menu. (See page 31.)

CAUTION• Make sure to turn both the projector and the video equipment off, before

connecting.

S-video cable (commercially available)

Video cable (commercially available)

Projector

* The (HD/C sync) and (VD)terminals may be used dependingon the specifications of the DTVdecoder connected to thisprojector. Please refer to theoperation manual of the DTVdecoder for details.

E-15

Setu

p &

Con

nect

ions

Connecting to a ComputerWhen the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, crosstype, commercially available), the computer can be used to control the projector and check the status of theprojector. See pages 52, 53 and 54 for details.

Connecting to a computer using the INPUT 5 COMPUTER-RGB port1 Connect one end of the RGB cable (commercially available) to the INPUT 5 COMPUTER-RGB port on the

projector.2 Connect the other end of the corresponding port on a computer.

Connect an RS-232C cable (null modem, cross type, commercially available) to the serial port on the computer.

CAUTION• Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.

• Refer to “Computer Compatibility Chart” on page 56 for a list of computer signals compatible with the projector. Use with computersignals other than those listed may cause some of the functions not to work.

• The RS-232C function may not operate if your computer port is not correctly set up. Please refer to the operation manual of the computer fordetails.

• The arrows (→, ↔) in the configuration above indicate the direction of the signals.• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized SharpVision Service Center

or Dealer.

RGB cable(commercially available)

RS-232C cable (null modem, crosstype, commercially available)

12

E-16

Setup & Connections

Operating the Remote ControlThe remote control can be used to control the projec-tor within the range shown on the left.

• The signal from the remote control can be reflected off ascreen for easy operation. However, the effective distanceof the signal may differ due to the screen material.

Remote Control

Remote Control

45˚

23 (7 m)

30˚

30˚

45˚

30˚

Using the remote control in a darkroom

The backlights of the operation buttons can be turnedon for five seconds and off by pressing BACKLIGHT.If you want to turn off the backlights while they are on,press BACKLIGHT again.

BACKLIGHT button

Using as a Wired Remote ControlWhen the remote control cannot be used due to therange or positioning of the projector (rear projection,etc.), connect a 3.5 mm stereo minijack cable(commercially available) from the wired remote controljack on the top of the remote control to the Wired remotecontrol jack on the back of the projector.

3.5 mm stereo minijack cable(commercially available)

E-17

Setu

p &

Con

nect

ions

Power ON/OFF

Press POWER ON.

• The flashing blue LAMP REPLACEMENT indicatorshows that the lamp is warming up. Wait until theindicator stops flashing before operating the projector.

• If the power is turned off and then immediately turnedon again, it may take a short while before the lampturns on.

• After the projector is unpacked and turned on for the firsttime, a slight odor may be emitted from the exhaustventilative hole. This odor will soon disappear with use.

When the power is on, the LAMP REPLACEMENTindicator lights, indicating the status of the lamp.Blue: Lamp is ready.Flashing blue: Warming up.Red: Change the lamp.

Press POWER OFF.

Press POWER OFF again while the message isdisplayed.

• If you accidentally pressed POWER OFF and do not wantto turn off the power, wait until the message disappears.

• When POWER OFF is pressed twice, the POWER indicatorwill light up red and the cooling fan will run for about 90seconds. The projector will then enter standby mode.

• Wait until the cooling fan stops running before disconnectingthe power cord.

• The power can be turned on again by pressing POWERON. When the power is turned on, the POWER indicatorand the LAMP REPLACEMENT indicators light blue.

TEMP. LAMP POWER

POWERbuttons

Zooming and Focusing

The picture can be zoomed in or out, and focused by the Zoom knob and the Focus ring.

1 Slide the Zoom knob. The image can beadjusted to the desired size within the zoomrange.

2 Rotate the Focus ring until the image on thescreen becomes clear.1

2

E-18

Setup & Connections

Using the Adjustment Feet

Setting Up the Screen

You can adjust the height of the image by raising the projector withthe foot releases.

1 Press the foot releases and lift the projector to the desired angle.2 Remove your hands from the foot releases. Once the adjustment

feet have locked in position, release the projector.3 If the screen is at an angle, the adjusters can be used to adjust

the angle of the image.

Returning the projector to its original positionWhile holding the projector, press the foot releases and slowly lowerthe projector to its original position.

CAUTION• Do not hold the lens when lifting or lowering the projector.• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment feet and the

projector.

• The projector is adjustable up to approximately 5° from the standard position.• When the height of the projector is adjusted, the image may become distorted (keystoned), depending on the relative

positions of the projector and the screen. See page 19 for details on the keystone correction.

The picture can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of theprojector using your finger.

Using the Lens Shift

Lens shift dial

DOWN UP

Projector Projected Image

UP

DOWN

1

3

E-19

Setu

p &

Con

nect

ions

Keystone CorrectionThis function can be used to adjust the Keystonesettings.

1 Press KEYSTONE on the remote control.

2 Press ENTER to display the test pattern.

3 Press / / / to make adjustments.

4 a. Press KEYSTONE to return to the normalscreen.

b. To reset the Keystone setting, press UNDO.

• Straight lines and the edges of the displayed image mayappear jagged, when adjusting the Keystone setting.

3

4b 2

1,4a

E-20

Setup & Connections

Adjusting the Projection DistancePosition the projector perpendicular to the screen with all feet flat and leveled to achieve an optimal image.Move the projector forward or backward if the edges of the image are distorted.

• The projector lens should be centered in the middle of the screen. If the lens center is not perpendicular to the screen, theimage will be distorted, making viewing difficult.

• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colors,making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

• A polarizing screen cannot be used with this projector.

Standard Setup (Front Projection)Place the projector at the required distance from thescreen according to the desired screen size. (See thetables below.) The figures in the tables are basedupon projecting an image so that it occupies theentire screen.

The formula for screen size and projection distance

• There is an error of ±3% in the formula above.• Values with a minus (–) sign indicate the distance of the lens center below the bottom of the

screen.

The formula for screen size and projection distance

• There is an error of ±3% in the formula above.• Values with a minus (–) sign indicate the distance of the lens center below the bottom of the screen.

When using a widescreen (16:9)In case of displaying the16:9 picture on the wholeof the 16:9 screen.

y1 (Max.) = (0.05058x – 0.0447) × 3.28y2 (Min.) = (0.03734x – 0.0447) × 3.28z1 (Upper) = 0z2 (Lower) = –0.45x

Diag. (x)300"250"200"150"133"106"100"92"84"72"60"40"

Width261"218"174"131"116"92"87"80"73"63"52"35"

Height147"123"98"74"65"52"49"45"41"35"29"20"

Maximum (y1)54'1" (16.5 m)45'1" (13.7 m)36' (11.0 m)

26'12" (8.2 m)23'11" (7.3 m)18'11" (5.8 m)17'11" (5.5 m)16'5" (5.0 m)15' (4.6 m)

12'10" (3.9 m)10'8" (3.3 m)7'1" (2.2 m)

Minimum (y2)39'11" (12.2 m)33'3" (10.1 m)26'7" (8.1 m)19'11" (6.1 m)17'7" (5.4 m)13'11" (4.3 m)13'2" (4.0 m)12'1" (3.7 m)11'1" (3.4 m)9'6" (2.9 m)

7'10" (2.4 m)5'2" (1.6 m)

Upper (z1)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)

Screen size (16:9) Projection Distance (y)Distance from the lens center to the

lower edge of the image (z)

Lower (z2)–12'3" (–374 cm)–10'3" (–311 cm)–8'2" (–249 cm)–6'2" (–187 cm)–5'5" (–166 cm)–4'4" (–131 cm)–4'1" (–125 cm)–3'9" (–114 cm)–3'5" (–105 cm)–2'11" (–90 cm)–2'5" (–75 cm)–1'8" (–50 cm)

x : Screen size (diag.) (inches)y : Projection distance (feet)z : Distance from the lens center to the lower

edge of the screen (feet)

When using a normalscreen (4:3)In case of setting the16:9 picture to the fullhorizontal width of the4:3 screen.

y1 (Max.) = (0.05510x – 0.04593) × 3.28y2 (Min.) = (0.04068x – 0.04369) × 3.28z1 (Upper) = 0z2 (Lower) = –0.4904x

Diag. (x)250"200"150"100"84"72"60"

Width200"160"120"80"67"58"48"

Height150"120"90"60"50"43"36"

Maximum (y1)41'4" (12.6 m)33' (10.1 m)24'9" (7.5 m)16'5" (5.0 m)13'9" (4.2 m)11'10" (3.6 m)9'10" (3.0 m)

Minimum (y2)30'6" (9.3 m)24'4" (7.4 m)18'3" (5.6 m)12'1" (3.7 m)10'2" (3.1 m)8'8" (2.6 m)7'2" (2.2 m)

Upper (z1)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)0" (0 cm)

Screen size (4:3) Projection Distance (y) Distance from the lens center to thelower edge of the image (z)

Lower (z2)–12'6" (–286 cm)–10' (–229 cm)–7'6" (–171 cm)–5' (–114 cm)–4'2" (–96 cm)–3'7" (–82 cm)–3' (–69 cm)

x : Screen size (diag.) (inches)y : Projection distance (feet)z : Distance from the lens center to the lower

edge of the screen (feet)

z

x

y

3

4

: Screen area: Picture area

9

16

: Picture area

E-21

Setu

p &

Con

nect

ions

Adjusting the Projection Distance

Upper and Lower Lens Shift Position• This projector is equipped with a lens shift function that lets you adjust the projection height.• Adjust it to match the setup configuration.• The screen can be moved maximum the length of one screen vertically using the lens shift.

• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. Tilting or anglingthe projector will reduce the effectiveness of the lens shift function.

Screen size: 100 inches (254 cm)Aspect ratio: 16:9

90°

90°

Screen

Upper and Lower Lens Shift Position (Ceiling Mount)When the projector is in the inverted position, use the upper edge of the screen as the base line, and exchangethe lower and upper lens shift values.

Screen

Upper lens shift position(High mount setup)

Lower lens shift position(Desktop setup)

Lens center

Lens center

90°

90°

Screen size: 100 inches (254 cm)Aspect ratio: 16:9

Lower edge of screen (White portion) =Standard (0) point

E-22

Setup & Connections

Rear Projection• Place a translucent screen between the projector and

the audience.• Use the projector ’s menu system to reverse the

projected image. (See page 43 for use of thisfunction.)

• Optimal image quality can be achieved when the projectoris positioned perpendicular to the screen with all feet flatand leveled.

Projection Using a Mirror• When the distance between the projector and screen

is not sufficient for normal rear projection, you canuse a mirror to reflect the image onto the screen.

• Place a mirror (normal flat type) in front of the lens.• Project the normal image onto the mirror.• The image reflected from the mirror is projected onto

the translucent screen.

CAUTION• When using a mirror, be sure to carefully position both the

projector and the mirror so the light does not shine into theeyes of the audience.

• It is recommended that you use the optional Sharpceiling-mount bracket for this installation.

• Before mounting the projector, contact your nearestAuthorized SharpVision Service Center or Dealer toobtain the recommended ceiling-mount bracket(commercially available). (AN-CM230 ceiling-mountbracket, AN-EP101A extension tube for AN-CM230.)

• When the projector is in the inverted position, use theupper edge of the screen as the base line.

• Use the projector ’s menu system to select theappropriate projection mode. (See page 43 for useof this function.)

Ceiling-mount Projection

Image Projection

E-23

Oper

atio

n Bu

ttons

Selecting the Input Signal Source

Using the Operation Buttons

Press INPUT on the projector, INPUT 1, INPUT 2,INPUT 3, INPUT 4 or INPUT 5 on the remote controlto select the desired input mode.

• When no signal is received, “NO SIGNAL” will be displayed.When a signal that the projector is not preset to receive isreceived, “NOT REG.” will be displayed.

On-screen Display

Adjusting the Picture Aspect RatioThis function allows you to modify or customize thepicture display mode to enhance the input image.Depending on the input signal, you can choose SIDEBAR, SMART STRETCH, CINEMA ZOOM, STRETCH,NORMAL, or DOT BY DOT image.

1 Press RESIZE. Each time RESIZE is pressed, thepicture mode changes as shown on the next page.

2 To return to the standard image, press UNDOwhile “RESIZE” is displayed on the screen.

INPUT buttons

12

INPUT 1 Mode INPUT 2 Mode

INPUT 5 Mode INPUT 4 Mode

INPUT 3 Mode

E-24

Operation Buttons

COMPUTER

EXAMPLE

960 720 1280 720

480i480PNTSCPAL

SECAM

960 720 1280 720480P

1280 720 –720P

1280 720 –

1280 720

1280 720

1280 720

SIDE BAR STRETCHCINEMAZOOM

SMARTSTRETCH

1280 720

–

–

–

–1080i

For 4:3 aspect ratio


EXAMPLE

VGA

SVGA

XGA

SXGA

Input Signal NORMALOutput screen image

DOT BY DOT

For 4:3 aspect ratio(640 480)

For 4:3 aspect ratio(800 600)

For 4:3 aspect ratio (1024 768)

For 5:4 aspect ratio (1280 1024)

960 720 800 600 SVGA (800 600)

NORMAL DOT BY DOT


For without 4:3 aspect ratio

960 720 1024 720XGA (1024 768)

960 720 1280 720SXGA (1280 960)

900 720 1280 720SXGA (1280 1024)

480i480PNTSCPAL

SECAM

720P1080i

Input Signal SIDE BAR SMART STRETCHOutput screen image

STRETCHCINEMA ZOOM


Letter box image


With squeeze

VIDEO/DVD/DTV

Adjusting the Picture Aspect Ratio

E-25

Oper

atio

n Bu

ttons

Gamma Correction Function• Gamma is an image quality enhancement function

that offers a richer image by brightening the darkerportions of the image without altering the brightnessof the brighter portions.

• Four gamma settings are available to allow fordifferences in the images displayed and in thebrightness of the room.

• When you are displaying images with frequent, darkscenes, such as a film or concert, or when you aredisplaying images in a bright room, this feature makesthe dark scenes easier to see and gives theimpression of greater depth in the image.

Gamma Modes

On-screen Display

ss

s

STANDARD

GAMMA 1

GAMMA 2

CUSTOM

Gamma modeSelected Mode

STANDARD

GAMMA 1

GAMMA 2

CUSTOM

Standard picture without gamma correction.

Brightens darker portions of images for moreenhanced presentations.

Gives greater depth to darker portions ofimages for a more exciting theater experience.

Allows you to adjust gamma value usingSharpVision Manager (supplied).

1 Press GAMMA to display “GAMMA”. Then, thepresent Gamma mode is displayed.

2 Each time GAMMA is pressed, the gamma leveltoggles as shown on the left.

3 To return to the standard image, press UNDOwhile “GAMMA” is displayed on the screen.

• The CUSTOM setting of VIDEO mode optimizes the videosource to reproduce the image more beautifully. It darkensbright portions of the image and gives greater depth todarker portions of the image.Select CUSTOM as your default setting if you prefer asmooth textured image to a sharply contrasted one.

• STANDARD and GAMMA 2 settings of VIDEO mode (exceptCOMPONENT 480P/720P/1080i) incorporate a DYNAMICGAMMA function for optimizing GAMMA correction frameby frame in real time, thus providing a more beautiful image.

• GAMMA 1 settings are the same for both RGB and VIDEOmodes.

3

1,2

E-26

Basic Operation

Basic Operations

Using the GUI (Graphical User Interface) Menu Screen

(GUI) On-screen Display

1

INPUT 3, 4 (VIDEO) mode

1

INPUT 1, 2 (COMPONENT) or 5 (RGB) mode

4 1 Press MENU to display the INPUT 1, 2, 3, 4 or 5mode menu bar.

2 Press / to select an adjustment main menuon the menu bar.

3 Press / to select a specific adjustment item.

4 To display a single adjustment item, press ENTERafter selecting the item. Only the menu bar andthe selected adjustment item will appear.

5 Press / to adjust the item.

6 Press UNDO to return to the previous screen.

7 To exit the GUI, press MENU.

• For details on items on the menu screen, see the tree chartson pages 27 and 28.

This projector has two sets of menu screens that allowyou to adjust the image and various projector settings.These menu screens can be operated from the projectoror the remote control with the following procedure.

5

5

2

3

2

3

2

5

1,74

6

2,3,5

Main menu

Sub menu

E-27

Basi

c Op

erat

ion

Menu Bars

Items on the INPUT 3 or 4 Mode Menu Bar

Main menu Sub menu Main menu Sub menuPicture

Tint 3030

Color 3030

Sharp 3030

Contrast 3030

Brightness 3030

Red 3030

Blue

Reset

3030

CLR Temp

Lamp Timer

Theater Mode

Progressive Mode

33

2D Progressive

3D Progressive

Film Mode

Economy Mode

Background

[ON/OFF]Auto Power Off

RS-232C Port [ON/OFF]

Options 3D DNR

OSD Display

[ON/OFF]

[NORMAL/BRIGHT]

Video Systems

Normal

PAL (50/60Hz)

Level A

SECAM

Level B

Auto

NTSC3.58

PAL–M

PAL–N

NTSC4.43

Language English

Deutsch

Español

Nederlands

Français

Italiano

Svenska

Português

Status

Blue

None

RS-232C 9600bps

115200bps

38400bps

Subtitle 3030

PRJ Mode Front

CeilingFront

Rear

CeilingRear

*

* These values may be changed using the RESIZE mode.

• Only the items highlighted in the tree charts above can be adjusted.• To adjust the items under the sub menu, press after selecting the sub menu.

E-28

Basic Operation

Menu Bars

Items on the INPUT 1, 2 or 5 Mode Menu Bar

Main menu Sub menu Main menu Sub menuPicture PRJ Mode

Options

Fine Sync

Tint 3030

Color 3030

Sharp 3030

Contrast 3030

Brightness 3030

Red 3030

Blue

Reset

3030

CLR Temp

Progressive Mode

Signal Type

33 Component

RGB

2D Progressive

3D Progressive

Film Mode

Auto Sync

Clock 150150

150150

Auto Sync Disp [ON/OFF]

Phase 6060

H-Pos

V-Pos

Reset

Save Setting

Select Setting

Special Modes

6060

Signal Info

12•

•

7

Resolution800600640480


12•

•

7

Vert Freq75 Hz72 Hz

12•

•

7


Vert Freq75 Hz72 Hz

ResolutionHor FreqVert Freq

64048037.5 kHz72 Hz

Economy Mode

OSD Display

Background

[ON/OFF]

[ON/OFF]Auto Power Off

RS-232C Port [ON/OFF]

Subtitle 3030

3D DNR

Blue

None

Normal

Level A

Level B

Language English

Deutsch

Español

Off

Normal

High Speed

Nederlands

Français

Italiano

Svenska

Português

Status

Lamp Timer

Theater Mode

RS-232C

*,**

*

9600bps

115200bps

38400bps

Front

CeilingFront

Rear

CeilingRear

*

[NORMAL/BRIGHT]

* Not displayed in the INPUT 5 mode.** These values may be changed using the RESIZE mode.

• The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.• “Color”, “Tint”, and “Sharp” appear only when Component is selected in INPUT 1 or 2 mode.• Only the items highlighted in the tree charts above can be adjusted.• To adjust the items under the sub menu, press after selecting the sub menu.

E-29

Basi

c Op

erat

ion

Adjusting the PictureYou can adjust the projector’s picture to your prefer-ences with the following picture settings.

Description of Adjustment Items

For less contrastFor less brightnessFor less color intensitySkin tones become purplishFor less sharpnessFor weaker redFor weaker blue

Selected item

For more contrastFor more brightnessFor more color intensitySkin tones become greenishFor more sharpnessFor stronger redFor stronger blue

button button

All image adjustment items are returned to the factory presetsettings.

ContrastBrightnessColorTintSharpRedBlueReset

(GUI) On-screen Displaye. g. (VIDEO input in INPUT 3 or 4 mode)

1

2

1,4

2,3

• “Color”, “Tint” and “Sharp” do not appear for RGB input inINPUT 5 mode.

1 Press MENU. Menu bar and “Picture” menuscreen appear. GUI operation guide is alsodisplayed.


3 Press / to move the mark of the selectedadjustment item to the desired setting.


• To reset all adjustment items, select “Reset” on the “Picture”menu screen and press ENTER.

• The adjustments can be stored separately in the INPUT 1to 5 modes.

E-30

Basic Operation

Adjusting the Picture

Adjusting the Color TemperatureThis function can be used to adjust the colortemperature to suit the type of image input to theprojector (DVD, video, computer image, TV broadcast,etc.).This function can be operated using the CLR TEMPbuttons on the remote control, as well as the GUI menuscreen.

Adjusting the Color Temperature with theRemote Control

1 Press CLR TEMP (–/+) on the remote control.Then, the present color temperature level isdisplayed.

2 Press CLR TEMP (–/+) to change the colortemperature level.

• The descriptions of each of the button operations areshown on the table below.

• “ ” disappears after four-seconds of no-operation.

Adjusting the Color Temperature using theGUI Menu Screen

Description of Color Temperature


2 Press / to select “CLR Temp”.

3 Press / to move the mark of the colortemperature setting to the desired setting.


Increases color temperature forcooler, bluish, florescent-likeimages.(High color temperature)

Decreases color temperature forwarmer, reddish,incandescent-like images.(Low color temperature)

3 3(Red) button button (Blue)

1,2


1,4

2,3

On-screen Display

E-31

Basi

c Op

erat

ion

Selecting the Signal TypeThis function allows you to select the input signal typeCOMPONENT or RGB for INPUT 1 or 2.


2 Press / to select “Signal Type”, and thenpress .

3 Press / to select “RGB” or “Component”.

4 Press ENTER to save the setting.


Adjusting the Picture



Progressive ModeThis function allows you to select the progressive displayof a video signal. The progressive display projects asmoother video image.


2 Press / to select “Progressive Mode”, andthen press .

3 Press / to select “2D Progressive”, “3DProgressive” or “Film Mode”.



Selects the following progressive conversion mode.

2D ProgressiveThis function is useful to display fast-moving images such assports and action films. This mode optimizes the image in adisplayed frame.

3D ProgressiveThis function is useful to display relatively slow-moving imagessuch as drama and documentary more clearly.This mode optimizes the image by estimating the movementof a number of preceding and succeeding frames.

Film ModeReproduces the image of film software clearly. Displays theoptimized image of film transformed with three-two pull downenhancement to progressive mode images.

• Film Mode cannot work with PAL 50 Hz.

41,5

2,3

1,5

2,3

4

E-32

Basic Operation

When displaying computer patterns which are verydetailed (tiling, vertical stripes, etc.), interference mayoccur between the DMD pixels, causing flickering,vertical stripes, or contrast irregularities in portions ofthe screen. Should this occur, adjust “Clock”, “Phase”,“H-Pos” and “V-Pos” for the optimum computer image.

• Computer image adjustments can be made easily by pressingAUTO SYNC ( ) on the remote control. See page 35 for details.

(Select the desired computer input mode with INPUT 1or 2.)

1 Press MENU.

2 Press / to select “Fine Sync”.


4 Press / to move the mark of the selectedadjustment item to the desired setting.


• To reset all adjustment items, select “Reset” on the “Fine Sync”menu screen and press ENTER.

• The adjustable area of each item may be changed using the inputsignal.


Adjusts vertical noise.Adjusts horizontal noise (similar to tracking on your VCR).Centers the on-screen image by moving it to the left or right.Centers the on-screen image by moving it up or down.All computer image adjustment items are returned to the factorypreset settings.

ClockPhaseH-PosV-PosReset

Description of Adjustment Items

2

DescriptionSelected item

Adjusting the Computer Images (RGB menu only)

3

1,5

2,3,4

E-33

Basi

c Op

erat

ion


Saving and Selecting Adjustment SettingsThis projector allows you to store up to seven adjustmentsettings for use with various computers. Once thesesettings are stored, they can be easily selected eachtime you connect a computer to the projector.

Saving the adjustment setting

1 Press MENU.


3 Press / to select “Save Setting”, and thenpress .

4 Press / to select the desired memory locationof the setting.



Selecting a saved setting

1 Press MENU.


3 Press / to select “Select Setting”, and thenpress .

4 Press / to select the desired memory setting.

5 Press ENTER to select the setting.

6 To exit from the GUI, press MENU.

• If a memory position has not been set, the resolution and frequencysetting will not be displayed.

• When selecting the stored adjustment setting with “Select Setting”,the computer system should match the stored setting.


2

3

3

1,6

5

2,3,4

E-34

Basic Operation


Special Mode AdjustmentOrdinarily, the type of input signal is detected and thecorrect resolution mode is automatically selected.However, for some signals, the optimal resolution modein “Special Modes” on the “Fine Sync” menu screenmay need to be selected to match the computer displaymode.

1 Press MENU.


3 Press / to select “Special Modes”, and thenpress .

4 Press / to select the optimal resolution.



• Avoid displaying computer patterns which repeat every other line(horizontal stripes). (Flickering may occur, making the image hardto see.)

• When inputting DTV 1080i signal, select the corresponding type ofsignal in step 4 above.



Checking the Input Signal

This function allows you to check the current input signalinformation.

1 Press MENU.


3 Press / to select “Signal Info” to display thecurrent input signal.


1,6

5

2,3,4

1,4

2,3

E-35

Basi

c Op

erat

ion


Auto Sync Adjustment• Used to automatically adjust a computer image.• Auto Sync adjustment can be made manually by

pressing the AUTO SYNC button on the remotecontrol, or automatically by setting “Auto Sync” to“Normal” or “High Speed” in the projector’s GUI menu.

OFF• Synchronized adjustment is not automatically

performed.• Press AUTO SYNC to perform manual adjustment.Normal• Synchronized adjustment is automatically performed

the same as the “High Speed” setting.• Adjustment using the “Normal” setting takes longer

to perform than using the “High Speed” setting, but itis more accurate.

High Speed• The sync adjustment is automatically made each time

the projector is turned on while connected to acomputer or the input selection is changed.

• The Auto Sync adjustment setting previously made iscleared when the projector’s setting is changed.

1 Press MENU.


3 Press / to select “Auto Sync”, and then press.

4 Press / to select “Normal” or “High Speed”.


• When the optimum image cannot be achieved with AutoSync adjustment, use manual adjustments. (See page 32.)

• When performing AUTO SYNC in off or High Speed mode,if you press AUTO SYNC once, then press it again withinone minute, AUTO SYNC will be executed in Normal mode.

During Auto Sync adjustment, the On-screen Displaychanges as shown on the left.

• The Auto Sync adjustment may take some time to complete,depending on the image of the computer connected to theprojector.


g

1,5

2,3,4

AUTO SYNCbutton

On-screen Display

g

When “Normal” is selected

When “High Speed” is selected

E-36

Basic Operation

Reducing Image Noise (VIDEO menu only)

Auto Sync Display FunctionNormally, an image is not superimposed during AutoSync adjustment. You can, however, choose tosuperimpose a background image during Auto Syncadjustment.

1 Press MENU.


3 Press / to select “Auto Sync Disp”.

4 Press / to select “ ” to superimpose abackground image or “ ” to remove thebackground image during Auto Sync adjustment.


2,3,4

1,5




3D Digital Noise Reduction (3D DNR) provides highquality images with minimal background.

1 Press MENU.

2 Press / to select “Options”.

3 Press / to select “3D DNR”.

4 Press / to select “ ” (ON).


• If the image is clear, select “ ” (OFF) to prevent any blurring.

2,3,4

1,5

E-37

Basi

c Op

erat

ion

Turning On/Off the On-screen DisplayThis function allows you to turn on or off the on-screenmessages that appear during input select.

1 Press MENU.


3 Press / to select “OSD Display”, and thenpress .

4 Press / to select the desired On-screenDisplay.




Setting the Video Signal (VIDEO menu only)The video input system mode is preset to “Auto”;however, it can be changed to a specific system modeif the selected system mode is not compatible with theconnected audiovisual equipment.

1 Press MENU.


3 Press / to select “Video Systems”, and thenpress .

4 Press / to select the desired video systemmode.



• When the system mode is set to “Auto”, you may not receivea clear picture due to signal differences. Should this occur,switch to the video system of the source signal.

• AUTO cannot be set for PAL-M and PAL-N input signals.Select “PAL-M” or “PAL-N” in “Video System” menu for PAL-M and PAL-N input signals.


DescriptionSelected item

NormalLevel A

Level B

Description of OSD Display

All On-screen Display are displayed.INPUT and AUTO SYNC are not displayed.All On-screen Display are not displayed (except MENU,KEYSTONE and warning display (Power off, Temp., Lampetc.)).

1,6

5

2,3,4

1,6

5

2,3,4

E-38

Basic Operation

Selected item

Theater Mode FunctionsFunction as a toggle switch for controlling the quantityof projected light. Select “NORMAL” or “BRIGHT” todecrease or increase brightness, power consumptionand fan noise.This function can be operated using the THEATERMODE button on the remote control, as well as the GUImenu screen.

Description of Theater Modes

Operating the Theater Mode Function withthe Remote Control

1 Press THEATER MODE on the remote control.The present Theater Mode is displayed.“ ” disappears after four-seconds ofno-operation.

• “Theater Mode” is factory preset to “BRIGHT” .• When selecting “BRIGHT” in “Theater Mode”, the fan noise

is increased.• Even when selecting “NORMAL” in “Theater Mode“, fan

noise may increase if internal temperature rises enough toactivate the cooling function.

Operating the Theater Mode Function Usingthe GUI Menu Screen

1 Press MENU.


3 Press / to select “Theater Mode”.

4 Press / to select “ ” or “ ”.


Quantity of light is 70%.Power consumption is 310 W.

Quantity of light is 100%.Power consumption is 365 W.

1

On-screen Display


1,5

2,3,4

Description

NORMAL ( )

BRIGHT ( )

E-39

Basi

c Op

erat

ion

Selecting a Background Image


This function allows you to select the image displayedwhen no signal is being sent to the projector.

Description of Background Images

1 Press MENU.


3 Press / to select “Background”, and thenpress .

4 Press / to select the background image youwant to display on the screen.



Selected item

Blue

None

Description

Blue screen

Black screen

1,6

5

2,3,4

E-40

Basic Operation

With this function, you can adjust the vertical size ofthe display to allow for subtitles.

Description of Subtitle Setting

1 Press MENU.


3 Press / to select “Subtitle”.

4 Press / to move the mark of the subtitlesetting.


• The RESIZE modes that are available for the Subtitle settingare SMART STRETCH and CINEMA ZOOM only. Please referto the page 24 for details.

• The value of the Subtitle setting may be changed using theINPUT and RESIZE mode.

• When changing the screen with the Subtitle setting, not onlythe bottom of the screen rises up but also the upper side ischanged to a certain point.

Digital shiftWhen the normal image is projected (without themenu screen or most On-screen Displays*displayed), / can be used to shift the imagedown or up. Press UNDO to return the image center.

* This function does not work when most On-screenDisplays are displayed. However, it can be usedwhen “INPUT 1”, “INPUT 2”, “INPUT 3”, “INPUT 4”or “INPUT 5” appears on the screen.

• This function only works with certain picture mode displays.


Subtitle Setting

1,5

2,3,4

Enlarges the image to adjust thevertical size of the display.

Compresses the image to adjustthe vertical size of the display.

30 30 button button

UNDO

'/"

Press ' Press " Press UNDO

On the final holeOn the final hole.On the final hole.

E-41

Basi

c Op

erat

ion

Selecting the Economy Mode


These functions allow you to reduce the powerconsumption when the projector is in stand-by mode.

RS-232C Off FunctionThis projector consumes power when using a computerconnected to the RS-232C port. When not using thisport, “RS-232C Port” can be set to “ ” for reducingstand-by power consumption.

Description of RS-232C Off

1 Press MENU.


3 Press / to select “RS-232C Port”.



• Set “RS-232C Port” to “ ” when using the SharpVisionManager (supplied).

1,5

2,3,4

On-screen Display


Automatic Power Shut-off FunctionWhen no input signal is detected for more than 15minutes, the projector will automatically shut off. Theon-screen message on the left will appear five minutesbefore the power is automatically turned off.

Description of Automatic Power Shut-off

1 Press MENU.


3 Press / to select “Auto Power Off”.



• “RS-232C Port” is factory preset to “ ”, and “Auto PowerOff” is factory preset to “ ”.

Power automatically shuts off after 15 minutes withoutan input signal.

Automatic Power Shut-off disabled.

Stand-by power for RS-232C connection turned off.

RS-232C on

E-42

Basic Operation

Selecting the Transmission Speed (RS-232C)This menu allows you to adjust the transmission speedof the RS-232C connection by selecting the baud rate.

1 Press MENU.


3 Press / to select “RS-232C”, and then press.

4 Press / to select the desired baud rate.



• Make sure that both the projector and computer are set forthe same baud rate. Refer to the computer’s operationmanual for instructions for setting the baud rate.


1,6

5

2,3,4

E-43

Basi

c Op

erat

ion

Reversing/Inverting Projected ImagesThis projector is equipped with a reverse/invert imagefunction which allows you to reverse or invert the pro-jected image for various applications.

Description of Projected ImagesSelected item

Front

CeilingFront

Rear

CeilingRear

Description

Normal image

Inverted image

Reversed image

Reversed and inverted image

1 Press MENU.

2 Press / to select “PRJ Mode”.

3 Press / to select the desired projection mode.



• This function is used for the reversed image and ceiling-mount setups. See page 22 for these setups.


41,5

2,3

Selecting the On-screen Display Language


English is the preset language for the On-screenDisplay; however, this can be changed to German,Spanish, Dutch, French, Italian, Swedish, Portuguese,Chinese, Korean or Japanese.

1 Press MENU.

2 Press / to select “Language”.

3 Press / to select the desired language.

4 Press ENTER to save the setting. The On-screenDisplay is now programed to display in thelanguage selected.


41,5

2,3

E-44

Basic Operation

Displaying the Adjustment SettingsThis function can be used to display all the adjustedsettings on the screen simultaneously.

1 Press MENU.

2 Press / to select “Status”.

3 Press ENTER to display all the adjustmentsettings.


2

3

INPUT 3, 4 (VIDEO) mode

2

3

INPUT 1, 2 (COMPONENT) or 5 (RGB) mode


1,43

2

E-45

Mai

nten

ance

&Tr

oubl

esho

otin

g

Lamp/Maintenance Indicators

Problem

• Blocked air intake.

• Clogged air filter.

• Cooling fan breakdown.• Internal circuit failure.

• Burnt-out lamp.• Lamp circuit failure.

• Lamp has been used forover 1,900 hours.

Maintenance Indicator

The internaltemperature isabnormally high.

TEMPERATUREWARNING indicator

Condition Possible Solution

• Relocate the projector to an area withproper ventilation.

• Clean the filters.(See page 49.)

• Take the projector to your nearestAuthorized SharpVision or Service Centeror Dealer for repair.

• Carefully replace the lamp. (See page 48.)• Take the projector to your nearest

Authorized Sharp Vision Service Center orDealer for repair.

Maintenance Indicators• The warning lights on the projector indicate problems

inside the projector.• There are two types of warning lights: a TEMPERATURE

WARNING indicator that warns you when the projectoris too hot, and a LAMP REPLACEMENT indicator thatwarns you when to change the lamp.

• If a problem occurs, either the TEMPERATUREWARNING indicator or the LAMP REPLACEMENTindicator will light up red. After turning off the power,follow the procedures given below.

• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector hascooled down completely before turning the power back on. (At least 5 minutes.)

• If the power is turned off and then turned on again, for example during a brief rest, the LAMP REPLACEMENT indicator maybe triggered, preventing the power from going on. Should this occur, unplug the power cord from the wall outlet and plug itback in again.

TEMPERATUREWARNINGindicator

POWERindicator

LAMPREPLACEMENTindicator

LAMP REPLACE-MENT indicator

The lamp does notlight up.

The lamp requiresreplacement.

TEMP. LAMP POWER

E-46

Maintenance &

Troubleshooting

Confirming the Lamp Usage Time

Lamp Maintenance

The lamp in this projector operates for approximately 2,000 cumulative hours, depending on the usage environ-ment. (As the usage environment can vary significantly, the projector lamp may not operate for 2,000 hours.) It isrecommended that the lamp be replaced after approximately 1,900 cumulative hours of use or when you notice asignificant deterioration of the picture and color quality. The lamp usage time can be checked with the On-screenDisplay.

CAUTION• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.

This function allows you to check the accumulated lampusage time.

1 Press MENU.

2 Press / to select “Options”. The lamp usagetime will be displayed in the “Lamp Timer” of“Options”.


• It is recommended that the lamp be replaced afterapproximately 1,900 cumulative hours of use. See page 48for lamp replacement.


Problem

• Lamp has been used for over 1,900hours.

• Lamp has been used for over 2,000hours.

Possible Solution

• Purchase a replacement lamp unit(lamp/cage module) of the currenttype BQC-XVZ9000/1 from yournearest Authorized SharpVisionService Center or Dealer.

• Replace the lamp. (See page 48.) Ifyou wish, you may have the lampreplaced at your nearestAuthorized SharpVision ServiceCenter or Dealer.

Condition

The LAMP REPLACEMENTindicator lights up red, and “LAMP”and “ ” will flash in yellow in thelower-left corner of the picture.

A significant deterioration of thepicture and color quality occurs.

The power will automatically turnoff and the projector will enterstand-by mode.

“LAMP” and “ ” will flash in red inthe lower-left corner of the picture,and the power will turn off.

1,3

2

E-47

Mai

nten

ance

&Tr

oubl

esho

otin

g

Replacing the Lamp

It is recommended that the lamp be replaced after approximately 1,900 cumulative hours of use or when younotice a significant deterioration of the picture and color quality. Carefully change the lamp by following the stepson the next page.If the new lamp does not light after replacement, take your projector to the nearest Authorized SharpVision ServiceCenter or Dealer for repair. Purchase a replacement lamp unit (lamp/cage module) of the current typeBQC-XVZ9000/1 from your nearest Authorized SharpVision Service Center or Dealer. Then carefully change thelamp by following the instructions on the next page. If you wish, you may have the lamp replaced at your nearestAuthorized SharpVision Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of thisprojector under warranty, including lamp replacement, must be obtained through an Authorized SharpVision ServiceCenter or Dealer. For the name of the nearest Authorized SharpVision Service Center or Dealer, please call toll-free:1-877-DTV-SHARP (1-877-388-7427). U.S.A. ONLY

CAUTION• There is potential glass particles hazard if the lamp ruptures. In case of lamp rupture, contact your

nearest Authorized SharpVision Service Center or Dealer for replacement.• Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely

hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cageto fully cool down before removing the lamp cage.

E-48

Maintenance &

Troubleshooting

Replacing the Lamp

• Be sure to remove the lamp cage by the handle. Do not touch the glass surface of the lamp cage or the inside of theprojector.

• To avoid injury to yourself and damage to the lamp, carefully follow the steps below.• Replace the lamp after turning off the power and unplugging the power cord.

Removing and installing the lamp unit

CAUTION

4 6Remove the lampcage. 5 Insert the new lamp

cage.

1 3Turn off the power. 2 Unplug the power cord. Remove the lamp cagecover.

Attach the lamp cagecover.

Close the lamp cage cover in thedirection of the arrow (to theclose mark) on the side of theprojector. Then tighten the userservice screw.

Remove the three-securingscrews from the lamp cage. Holdthe lamp cage by the handle andpull it horizontally towards you.

Loosen the user service screwthat secures the lamp cage coveron the side of the projector. Thenlower the cover in the direction ofthe arrow (to the open mark).

Press POWER OFF. Wait untilthe cooling fan stops running.

Press the lamp cage firmly intothe lamp cage compartment.Fasten the three-securing screws.

7 Plug in the power cord. Press POWER ON onprojector to reset lamptimer.

While holding down ENTER, "and |, press POWER ON.

8

• You need to reset lamp timer every time when replacing the lamp and confirm it to be reset on “Lamp Timer” menu.

1

2

User service screws

User service screws

E-49

Mai

nten

ance

&Tr

oubl

esho

otin

g

• This projector is equipped with air filters to ensure the optimal operating condition of the projector.• Periodically clean the air filter by vacuuming it off with a vacuum cleaner.• The air filter should be cleaned every 100 hours of use. Clean the filters more often when the projector is used

in a dirty or smoky location.

How to clean the air filterSide and Rear view

Cleaning the Air Filters

Air filter

Using the Kensington Lock

Kensington SecurityStandard connector

This projector has a Kensington Security Standardconnector for use with a Kensington MicroSaverSecurity System. Refer to the information that camewith the system for instructions on how to use it tosecure the projector.

Clean the dust off by putting thecleaner hose on the intakeventilative hole of the air filters.

Cleaning.2Unplug the powercord.1

Side view

Air filter

Bottom view

Cleaner hose

Cleanerhose

E-50

Maintenance &

Troubleshooting

Troubleshooting

Check• Projector power cord is not plugged into the wall outlet.• Selected input is wrong. (See page 23.)• Cables incorrectly connected to back panel of the projector. (See pages 13–15.)• Remote control batteries have run down. (See page 11.)• “Contrast” and “Brightness” adjustments are set to minimum position. (See page 29.)

• “Color” and “Tint” adjustments are not correct. (See page 29.)

• Adjust the focus. (See page 17.)• Projection distance is too long or too short to allow for proper focus. (See pages 20 and 21.)

• OSD Display is set to “Level A” or “Level B”, preventing to display some or all On-screenDisplays. (See page 37.)

• If the picture is normal, the sound is due to cabinet shrinkage caused by temperaturechanges. This will not affect operation or performance.

• Refer to “Lamp/Maintenance Indicators” on page 45.

• Adjust the “Phase” setting. (See page 32.)• Noise may appear when used with certain computers. Set the NOISE FILTER to ON

using the RS-232C command. (See pages 52–54.)

• Change the input signal type. (See page 31.)

For SHARP Assistance (U.S.A. only)

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”section on this page. If this operation manual does not answer your question, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an e-mail at [email protected] .Our World Wide Web address is http://www.sharp-usa.com/ .

ProblemNo picture appears.

Color is faded or poor.

Picture is blurred.

No OSD appears.

An unusual sound is occasion-ally heard from the cabinet.

Maintenance indicator lightsup.

Picture noise appears.

Image is green on INPUT 1 or2 COMPONENT.Image is pink (no green) onINPUT 1, 2 RGB.

E-51

Appe

ndix

Connecting Pin Assignments

INPUT 5 RGB Signal Input Port: 15-pin Mini D-sub female connectorRGB InputAnalog

1. Video input (red)2. Video input

(green/sync on green)3. Video input (blue)4. Not connected5. Composite sync6. Earth (red)7. Earth (green/sync on green)

8. Earth (blue)9. Not connected

10. GND11. GND12. Bi-directional data13. Horizontal sync signal14. Vertical sync signal15. Data clock

RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable

1161

15105

Pin No. Signal Name I/O Reference1 Not connected2 RD Receive Data Input Connected to internal circuit3 SD Send Data Output Connected to internal circuit4 Reserved Connected to internal circuit5 SG Signal Ground Connected to internal circuit6 Reserved Connected to internal circuit7 Reserved Connected to internal circuit8 Reserved Connected to internal circuit9 Not connected

9 6

5 1

E-52

Appendix

(RS-232C) Specifications and Command Settings

PC controlA computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,commercially available) to the projector. (See page 15 for connection.)

Communication conditionsSet the serial port settings of the computer to match those of the table on the next page.Signal format: Conforms to RS-232C standard.Baud rate: 9,600 bpsData length: 8 bitsParity bit: NONStop bit: 1 bitFlow control: None

Basic formatCommands from the computer are sent in the following order: command, parameter, and return code. After theprojector processes the command from the computer, it sends a response code to the computer.

Return code (0DH)C1 C2 C3 C4 P1 P2 P3 P4

Response code formatNormal response

O K Return code (0DH)

Problem response (communication error or incorrect command)

E R R Return code (0DH)

Command 4-digits Parameter 4-digits

Command format

When more than one code is being sent, send each command only after the OK response code for the previouscommand from the projector is verified.

• When using the computer control function of the projector, the projector operating status cannot be read to the computer.Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status withthe On-screen Display. If the projector receives a command other than a menu display command, it will execute the com-mand without displaying the On-screen Display.

Commands

EXAMPLE• When “Brightness” of INPUT 1 Picture Adjustment is set to 10.

→←R A B R 1 0_ O K

ProjectorComputer

E-53

Appe

ndix


CONTROL CONTENTS

POWER ON

POWER OFF

KEYSTONE (127 – 127)

INPUT 1 (COMPONENT 1)

INPUT 2 (COMPONENT 2)

INPUT 3 (S-VIDEO)

INPUT 4 (VIDEO)

INPUT 5 (COMPUTER-RGB)

AUTO SYNC START

INPUT 1 (COMPONENT 1) RESIZE : SIDE BAR

INPUT 1 (COMPONENT 1) RESIZE : SMART STRETCH

INPUT 1 (COMPONENT 1) RESIZE : CINEMA ZOOM

INPUT 1 (COMPONENT 1) RESIZE : STRETCH

INPUT 2 (COMPONENT 2) RESIZE : SIDE BAR

INPUT 2 (COMPONENT 2) RESIZE : SMART STRETCH

INPUT 2 (COMPONENT 2) RESIZE : CINEMA ZOOM

INPUT 2 (COMPONENT 2) RESIZE : STRETCH

INPUT 3 (S-VIDEO) RESIZE : SIDE BAR

INPUT 3 (S-VIDEO) RESIZE : SMART STRETCH

INPUT 3 (S-VIDEO) RESIZE : CINEMA ZOOM

INPUT 3 (S-VIDEO) RESIZE : STRETCH

INPUT 4 (VIDEO) RESIZE : SIDE BAR

INPUT 4 (VIDEO) RESIZE : SMART STRETCH

INPUT 4 (VIDEO) RESIZE : CINEMA ZOOM

INPUT 4 (VIDEO) RESIZE : STRETCH

INPUT 5 (COMPUTER-RGB) RESIZE : NORMAL

INPUT 5 (COMPUTER-RGB) RESIZE : DOT BY DOT

RGB GAMMA : STANDARD

RGB GAMMA : GAMMA1

RGB GAMMA : GAMMA2

RGB GAMMA : CUSTOM

VIDEO GAMMA : STANDARD

VIDEO GAMMA : GAMMA1

VIDEO GAMMA : GAMMA2

VIDEO GAMMA : CUSTOM

INPUT 1 (COMPONENT 1) CONTRAST (30 – 30)

INPUT 1 (COMPONENT 1) BRIGHTNESS (30 – 30)

INPUT 1 (COMPONENT 1) RED (30 – 30)

INPUT 1 (COMPONENT 1) BLUE (30 – 30)

INPUT 1 (COMPONENT 1) COLOR (30 – 30)

INPUT 1 (COMPONENT 1) TINT (30 – 30)

INPUT 1 (COMPONENT 1) SHARP (30 – 30)

INPUT 1 (COMPONENT 1) CLR TEMP (3 – 3)

INPUT 1 (COMPONENT 1) DISPLAY

INPUT 1 (COMPONENT 1) ADJUSTMENT RESET

INPUT 2 (COMPONENT 2) CONTRAST (30 – 30)

INPUT 2 (COMPONENT 2) BRIGHTNESS (30 – 30)

INPUT 2 (COMPONENT 2) RED (30 – 30)

INPUT 2 (COMPONENT 2) BLUE (30 – 30)

INPUT 2 (COMPONENT 2) COLOR (30 – 30)

INPUT 2 (COMPONENT 2) TINT (30 – 30)

INPUT 2 (COMPONENT 2) SHARP (30 – 30)

INPUT 2 (COMPONENT 2) CLR TEMP (3 – 3)

INPUT 2 (COMPONENT 2) DISPLAY

INPUT 2 (COMPONENT 2) ADJUSTMENT RESET

INPUT 5 (COMPUTER-RGB) CONTRAST (30 – 30)

INPUT 5 (COMPUTER-RGB) BRIGHTNESS (30 – 30)

INPUT 5 (COMPUTER-RGB) RED (30 – 30)

INPUT 5 (COMPUTER-RGB) BLUE (30 – 30)

INPUT 5 (COMPUTER-RGB) CLR TEMP (3 – 3)

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

P

P

K

I

I

I

I

I

A

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

G

G

G

G

G

G

G

G

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

R

O

O

E

R

R

V

V

R

D

A

A

A

A

B

B

B

B

B

B

B

B

A

A

A

A

C

C

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

B

B

B

B

B

B

B

B

B

B

C

C

C

C

C

W

W

Y

G

G

E

E

G

J

S

S

S

S

S

S

S

S

S

S

S

S

S

S

S

S

S

S

M

M

M

M

M

M

M

M

P

B

R

B

C

T

S

C

R

R

P

B

R

B

C

T

S

C

R

R

P

B

R

B

C

R

R

S

B

B

D

D

B

S

R

R

R

R

R

R

R

R

V

V

V

V

V

V

V

V

R

R

R

R

R

R

V

V

V

V

I

R

D

E

O

I

H

T

E

E

I

R

D

E

O

I

H

T

E

E

I

R

D

E

T

_

_

*

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

*

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

*

*

*

*

*

*

*

_

_

_

*

*

*

*

*

*

*

_

_

_

*

*

*

*

_

_

_

*

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

*

*

*

*

*

*

*

*

_

_

*

*

*

*

*

*

*

*

_

_

*

*

*

*

*

1

0

*

1

2

2

1

3

1

3

4

1

2

3

4

1

2

3

4

1

2

3

4

1

2

1

3

1

2

3

4

1

2

3

4

*

*

*

*

*

*

*

*

0

1

*

*

*

*

*

*

*

*

0

1

*

*

*

*

*

BUTT

ONS

& R

EMOT

E CO

NTRO

L KE

YPI

CTUR

E

COMMAND PARAMETER RETURN CONTROL CONTENTS

INPUT 5 (COMPUTER-RGB) DISPLAY

INPUT 5 (COMPUTER-RGB) ADJUSTMENT RESET

INPUT 1 (COMPONENT 1) SIGNAL TYPE : RGB

INPUT 1 (COMPONENT 1) SIGNAL TYPE : COMPONENT

INPUT 2 (COMPONENT 2) SIGNAL TYPE : RGB

INPUT 2 (COMPONENT 2) SIGNAL TYPE : COMPONENT

INPUT 1 (COMPONENT 1) 2D PROGRESSIVE


INPUT 1 (COMPONENT 1) Film MODE



INPUT 2 (COMPONENT 2) Film MODE

INPUT 3 (S-VIDEO) CONTRAST (30 – 30)

INPUT 3 (S-VIDEO) BRIGHTNESS (30 – 30)

INPUT 3 (S-VIDEO) RED (30 – 30)

INPUT 3 (S-VIDEO) BLUE (30 – 30)

INPUT 3 (S-VIDEO) COLOR (30 – 30)

INPUT 3 (S-VIDEO) TINT (30 – 30)

INPUT 3 (S-VIDEO) SHARP (30 – 30)

INPUT 3 (S-VIDEO) CLR TEMP (3 – 3)

INPUT 3 (S-VIDEO) DISPLAY

INPUT 3 (S-VIDEO) ADJUSTMENT RESET

INPUT 4 (VIDEO) CONTRAST (30 – 30)

INPUT 4 (VIDEO) BRIGHTNESS (30 – 30)

INPUT 4 (VIDEO) RED (30 – 30)

INPUT 4 (VIDEO) BLUE (30 – 30)

INPUT 4 (VIDEO) COLOR (30 – 30)

INPUT 4 (VIDEO) TINT (30 – 30)

INPUT 4 (VIDEO) SHARP (30 – 30)

INPUT 4 (VIDEO) CLR TEMP (3 – 3)

INPUT 4 (VIDEO) DISPLAY

INPUT 4 (VIDEO) ADJUSTMENT RESET

INPUT 3 (S-VIDEO) 2D PROGRESSIVE

INPUT 3 (S-VIDEO) 3D PROGRESSIVE

INPUT 3 (S-VIDEO) Film MODE

INPUT 4 (VIDEO) 2D PROGRESSIVE

INPUT 4 (VIDEO) 3D PROGRESSIVE

INPUT 4 (VIDEO) Film MODE

CLOCK (150 – 150)

PHASE (60 – 60)

H-POSITION (150 – 150)

V-POSITION (60 – 60)

RGB INPUT DISPLAY

RGB ADJUSTMENT RESET

SAVE SETTING (1 – 7)

SELECT SETTING (1 – 7)

RGB HORIZONTAL FREQUENCY CHECK

RGB VERTICAL FREQUENCY CHECK

NORMAL AUTO SYNC

HIGH SPEED AUTO SYNC

AUTO SYNC OFF

AUTO SYNC DISPLAY ON

AUTO SYNC DISPLAY OFF

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

kHz (***. *OR_)

Hz (***. *OR_)

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

R

R

I

I

I

I

R

R

R

R

R

R

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

V

I

I

I

I

I

I

M

M

T

T

A

A

A

I

I

C

C

A

A

B

B

A

A

A

B

B

B

B

B

B

B

B

B

B

B

B

B

A

A

A

A

A

A

A

A

A

A

B

B

B

A

A

A

N

N

A

A

A

A

E

E

F

F

A

A

A

M

M

R

R

S

S

S

S

I

I

I

I

I

I

P

B

R

B

C

T

S

C

R

R

P

B

R

B

C

T

S

C

R

R

I

I

I

I

I

I

C

P

H

V

R

R

M

M

R

R

D

D

D

A

A

E

E

I

I

I

I

P

P

P

P

P

P

I

R

D

E

O

I

H

T

E

E

I

R

D

E

O

I

H

T

E

E

P

P

P

P

P

P

L

H

P

P

E

E

S

L

Q

Q

J

J

J

S

S

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

*

*

*

*

*

*

_

_

_

_

_

_

_

_

_

_

*

_

*

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

*

*

*

*

*

*

*

_

_

_

*

*

*

*

*

*

*

_

_

_

_

_

_

_

_

_

*

*

*

*

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

*

*

*

*

*

*

*

*

_

_

*

*

*

*

*

*

*

*

_

_

_

_

_

_

_

_

*

*

*

*

_

_

_

_

_

_

_

_

_

_

_

0

1

1

2

1

2

0

1

2

0

1

2

*

*

*

*

*

*

*

*

0

1

*

*

*

*

*

*

*

*

0

1

0

1

2

0

1

2

*

*

*

*

0

1

*

*

1

2

1

2

0

1

0

PICT

URE

FINE

SYN

C *1

COMMAND PARAMETER RETURN

E-54

Appendix


• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the rangeindicated in brackets under CONTROL CONTENTS.

• *1 FINE SYNC can only be set in the displayed RGB mode.

CONTROL CONTENTS

THEATER MODE NORMAL

THEATER MODE BRIGHT

VIDEO 3D DNR OFF

VIDEO 3D DNR ON

OSD DISPLAY ON

OSD DISPLAY OFF (LEVEL A)

OSD DISPLAY OFF (LEVEL B)

VIDEO SYSTEM SELECTION : AUTO

VIDEO SYSTEM SELECTION : PAL

VIDEO SYSTEM SELECTION : SECAM

VIDEO SYSTEM SELECTION : NTSC4.43

VIDEO SYSTEM SELECTION : NTSC3.58

VIDEO SYSTEM SELECTION : PAL_M

VIDEO SYSTEM SELECTION : PAL_N

BACKGROUND SELECTION : BLUE

BACKGROUND SELECTION : NONE

AUTO POWER OFF : NO USE

AUTO POWER OFF : USE

LAMP USAGE TIME

REVERSE OFF

REVERSE ON

INVERT OFF

INVERT ON

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

0–9999 (INTEGER)

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

T

T

3

3

I

I

I

M

M

M

M

M

M

M

I

I

A

A

T

I

I

I

I

H

H

D

D

M

M

M

E

E

E

E

E

E

E

M

M

P

P

L

M

M

M

M

M

M

N

N

D

D

D

S

S

S

S

S

S

S

B

B

O

O

T

R

R

I

I

D

D

R

R

I

I

I

Y

Y

Y

Y

Y

Y

Y

G

G

W

W

T

E

E

N

N

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

1

0

0

1

1

2

0

1

2

3

4

5

6

7

1

2

0

1

1

0

1

0

1

1

2

3

4

5

6

7

8

9

0

1OPTI

ONS

PRJ

MOD

E

COMMAND PARAMETER RETURN CONTROL CONTENTS

LANGUAGE SELECTION : ENGLISH

LANGUAGE SELECTION : DEUTSCH

LANGUAGE SELECTION : ESPAÑOL

LANGUAGE SELECTION : NEDERLANDS

LANGUAGE SELECTION : FRANÇAIS

LANGUAGE SELECTION : ITALIANO

LANGUAGE SELECTION : SVENSKA

LANGUAGE SELECTION :

LANGUAGE SELECTION : PORTUGUÊS



OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

OK OR ERR

M

M

M

M

M

M

M

M

M

M

M

E

E

E

E

E

E

E

E

E

E

E

L

L

L

L

L

L

L

L

L

L

L

A

A

A

A

A

A

A

A

A

A

A

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

_

1

1

LANG

UAGE

COMMAND PARAMETER RETURN

E-55

Appe

ndix

Wired Remote Control Terminal Specifications

Specifications of wired remote control input• ø3.5 mm minijack• External: GND• Internal: +3.3V

Function and transmission codes

Wired remote control function code

1 0 1 1 0 * * * * * * * * 1 0

C1 System Code C5 C6 Data Code C13 C14 C15

• System codes C1 to C5 are fixed at “10110”.• Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”.

LSB MSB

Sharp remote control signal format

Transmission format: 15-bit format

Wave form of output signal: Output using Pulse Position Modulation

D D D D D D D D D D D DD

67.5 ms 67.5 ms

“0”“1”“0”

D

“0”“0”“0”“1”

T0T1

t

t

26.4 µs

• t 264 µs• T0 1.05 ms• T1 2.10 ms

Transmission control code15 bit

• Pulse carrier frequency 37.91 kHz• Duty ratio 1:1

C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14

System Address

D to D Common Data Bit Reverse in D

Function Key Data BitData

ExpansionData

Deter-mination

Mask

C15 C1

1

D C2

0

C3

1

C4

1

C5

0

C6

1

C7

0

C8

0

C9

0

C10

0

C11

0

C12

0

C13

0

C14

1

C15

0

C1

1

D C2

0

C3

1

C4

1

C5

0

C6

0

C7

1

C8

1

C9

1

C10

1

C11

1

C12

1

C13

1

C14

0

C15

1

CONTROL ITEM

SYSTEM CODE

C1

1

1

1

1

1

1

1

1

1

1

ON

OFF

MENU

∂

ƒ

ß

©

ENTER

UNDO

THEATER MODE

0

0

0

0

0

0

0

0

0

0

C2

1

1

1

1

1

1

1

1

1

1

C3

1

1

1

1

1

1

1

1

1

1

C4

0

0

0

0

0

0

0

0

0

0

C5 C6

0

0

0

0

1

0

1

1

1

1

1

1

0

0

0

0

1

1

0

0

C7

1

1

1

1

1

0

1

1

0

0

C8

0

0

0

1

1

0

1

0

1

1

C9

1

1

0

1

1

1

0

1

1

1

C10 C11

0

0

0

0

0

0

0

0

0

0

1

0

1

0

0

1

1

1

1

0

C12

0

1

1

1

1

0

0

0

0

0

C13

1

1

1

1

1

1

1

1

1

1

C14

0

0

0

0

0

0

0

0

0

0

C15

DATA CODE JUDGEMENTCODE

JUDGEMENTCODECONTROL

ITEM

SYSTEM CODE

C1

1

1

1

1

1

1

1

1

1

1

1

RESIZE

GAMMA

CLR TEMP +

CLR TEMP –

AUTO SYNC

KEYSTONE

INPUT 1

INPUT 2

INPUT 3

INPUT 4

INPUT 5

0

0

0

0

0

0

0

0

0

0

0

C2

1

1

1

1

1

1

1

1

1

1

1

C3

1

1

1

1

1

1

1

1

1

1

1

C4

0

0

0

0

0

0

0

0

0

0

0

C5 C6

0

0

1

1

0

1

0

0

1

0

1

1

0

0

0

1

1

1

1

1

1

0

C7

1

0

1

0

0

1

0

0

1

0

1

C8

1

0

1

1

1

1

1

1

0

0

0

C9

1

0

1

1

1

1

1

1

1

1

1

C10 C11

0

0

1

1

1

1

0

1

1

1

1

1

1

0

1

1

0

0

0

0

0

0

C12

0

0

0

1

1

1

0

0

0

0

0

C13

1

1

1

1

1

1

1

1

1

1

1

C14

0

0

0

0

0

0

0

0

0

0

0

C15

DATA CODE

Example of Reverse D to

E-56

Appendix

Computer Compatibility Chart

Horizontal Frequency: 15–81 kHzVertical Frequency: 43–100 HzPixel Clock: 12–120 MHzCompatible with sync on green and composite sync signalsSXGA compatible in advanced intelligent compression or intelligent compressionAICS (Advanced Intelligent Compression and Expansion System) resizing technology

PC/MAC/WS

HorizontalFrequency

(kHz)

VerticalFrequency

(Hz)

VGA

PC

PC

SVGA

XGA

VESAStandard

Resolution

640 350

1,152 864

1,152 882

720 350

640 400

720 400

640 480

800 600

1,024 768

Display

Upscale

Advanced Intelligent

Compression

27.0 60

27.0 60

27.0 60

60

31.5 70

31.5 70

31.5 70

31.5 60

34.7 70

37.9 72

37.5 75

43.3 85

47.9

53.0

90

100

31.4 50

35.1 56

37.9 60

44.5 70

48.1 72

46.9 75

53.7 85

56.8 90

64.0 100

31.5 70

37.9 85

37.9

27.0

85

37.9 85

26.2 50

PC/MAC/WS

HorizontalFrequency

(kHz)

VerticalFrequency

(Hz)Resolution Display

AdvancedIntelligent

Compression

AdvancedIntelligent

Compression

54.3 60

67.5 75

75.7 80

65.9 72

54.8 60

67.4 74

64.0 60

VESAStandard

SXGA

MAC 16"

MAC 21"

PC/MAC 13"

PC/MAC 19"

PC (WS)

SGI (WS)

SUN (WS)

640 480

832 624

AdvancedIntelligent

Compression

Upscale

34.9

1,152 870 68.5

67

60.0

60.0 60

1,024 768

1,280 960

VGA

SVGA

SXGA

SXGA

XGA48.4 60

75

46.8 75

1,280 1,024 53.5 50

1,152 90060.9 66

71.9 76

49.6 75

75

64.0 70

64.1 72

35.5 43

40.3 50

58.1 72

68.7 85

73.5 90

77.2 96

80.6 100

56.5 70

Upscale

• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should thisoccur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on howto change display modes can be found in your notebook computer’s operation manual.

• This projector can receive 640 350 VESA format VGA signals, however, “640 400” will appear on the screen.

E-57

Appe

ndix

Dimensions

15 49

/ 50 (

406)

7 (1

78)

18 11/16 (475)

Units: inches (mm)

Front View

Bottom View

Side ViewTop ViewSide View

Rear View

E-58

Appendix

Specifications

Product typeModel

Video system

Display methodDLP panel

LensProjection lamp

Contrast ratioVideo input signal

S-video input signal

Component input signal

Horizontal resolutionRGB input signal

Pixel clockVertical frequency

Horizontal frequencyComputer control signal

Rated voltageInput current

Rated frequencyPower consumption

Power dissipationOperating temperature

Storage temperatureCabinet

I/R carrier frequencyDimensions (approx.)

Weight (approx.)Supplied accessories

Replacement parts

ProjectorXV-Z9000UPAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43DTV 480i/480P/720P/1080iDLP chip, RGB optical shutter methodPanel size: 0.8Display method: Single Panel Digital Micromirror Device (DMD™) by Texas InstrumentsDrive method: Digital Light Processing (DLP™)No. of dots: 921,600 dots (1,280 [H] 720 [V])1–1.35 zoom lens, F3.0, f=32.5–44.0 mm275 W NSH lamp1100:1RCA Connector: VIDEO (INPUT 4), composite video, 1.0 Vp-p, sync negative, 75 Ωterminated4-pin Mini DIN connector (INPUT 3)Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminatedC (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminatedRCA Connector (INPUT 1, 2)Y: 1.0 Vp-p, sync negative, 75 Ω terminatedPB: 0.7 Vp-p, 75 Ω terminatedPR: 0.7 Vp-p, 75 Ω terminated520 TV lines (NTSC 3.58 input), 750 TV lines (DTV 720P input)15-PIN MINI D-SUB CONNECTOR (INPUT 5):

RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive,75 Ω terminated

HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only)VERTICAL SYNC. SIGNAL: Same as above12–120 MHz43–100 Hz15–81 kHz9-pin D-sub connector (RS-232C Port)AC 100–240 V3.8 A50/60 Hz365 W (SELECTING “BRIGHT” in the “Theater Mode”)310 W (SELECTING “NORMAL” in the “Theater Mode”)1,400 BTU/hour41°F to 95°F (5°C to 35°C)4°F to 140°F (20°C to 60°C)Plastic38 kHz1811⁄16 (W) 7 (H) 1549⁄50 (D) (475 178 406 mm) (main body only)1811⁄16 (W) 7 (H) 191⁄2 (D) (475 178 496 mm) (including terminal cover)20.9 lbs. (9.5 kg) (main body only)Remote control, Two AA size batteries, Power cord (11 10, 3.6 m), Terminal cover, Lenscap (attached), CD-ROM, Projector operation manual, SharpVision Manager operationmanualLamp unit (Lamp/cage module) (BQC-XVZ9000/1), Remote control (RRMCG1657CESA),AA size batteries, Power cord (CACCU5013DE01), Terminal cover (CCOVA1985CE01),Lens cap (PCAPH1056CESA), CD-ROM (UDSKA0047CEN1), Projector operation manual(TINS-7416CEZZ), SharpVision Manager operation manual (TINS-7418CEZZ)

This SHARP projector uses a DMD chip. This very sophisticated chipcontains 921,600 pixels. As with any high technology electronicequipment such as large screen TVs, video systems and videocameras, there are certain acceptable tolerances that the equipmentmust conform to.

This unit has some inactive pixels within acceptable tolerances whichmay result in inactive dots on the picture screen. This will not affectthe picture quality or the life expectancy of the unit. If you have anyquestions about this matter, please call toll free 1-877-DTV-SHARP(1-877-388-7427). U.S.A. ONLY

Specifications are subject to change without notice.

E-59

Appe

ndix

Glossary

Aspect ratioWidth and height ratio of an image. The normal aspect ratio of a computer and video image is 4 : 3. There are also wide images with an aspect ratio of 16 : 9and 21 : 9.

Auto SyncOptimizes projected computer images by automatically adjusting certain characteristics.

BackgroundInitial setting image projected when no signal is being input.

Cinema zoomMode that projects the 16:9 image which uses the center of the image signal on the full-screen.

ClockClock adjustment is used to adjust vertical noise when clock level is incorrect.

CLR Temp (Color temperature)Function that can be used to adjust the color temperature to suit the type of image input to the projector. Decrease the color temperature to create warmer,reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.

Composite syncSignal combining horizontal and vertical sync pulses.

Digital keystone correctionFunction to digitally correct a distorted image when the projector is set up at an angle, smoothes out jaggies on keystone images and compresses the imagenot only horizontally but vertically keeping the 4 : 3 aspect ratio.

Digital shiftShifts image up or down easily by / buttons when RESIZE mode of input image is SMART STRETCH, CINEMA ZOOM, or DOT BY DOT of COMPUTER,VIDEO and DTV inputs.

Dot by dotMode that projects images in their native resolution.

GAMMAImage quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighterportions. You can select four different modes : STANDARD, GAMMA 1, GAMMA 2 and CUSTOM.

Intelligent compression and expansionHigh quality resizing of lower and higher resolution images to fit the projector’s native resolution.

Lens shiftThe lens can be easily raised and lowered to minimize or eliminate “Keystone” type effect.

PhasePhase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontalflicker.

Progressive ModeThe progressive display projects a smoother video image. You can select three different modes : 2D Progressive, 3D Progressive and Film Mode.

RESIZEAllows you to modify or customize the picture display mode to enhance the input image. You can select six different modes: SIDE BAR, SMART STRETCH,CINEMA ZOOM, STRETCH, NORMAL, and DOT BY DOT.

RS-232CFunction to control the projector from the computer by using the RS-232C ports on the projector and computer.

Side barMode that projects the normal 4:3 image at the 4:3 area for the center of the screen.

Smart StretchMode that stretches the right and left sides of the 4:3 image horizontally while maintaining the aspect ratio around the center of the image to display it on the WIDEscreen.

Status functionDisplays the settings of each adjustment item.

StretchMode that stretches the 4:3 image horizontally to display it on the WIDE screen.

Sync on greenVideo signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin.

3D DNR (3D Digital Noise Reduction)Provides high quality images with minimal background.

E-60

Appendix

Index

AAC socket .......................................................................... 13ADJUSTMENT buttons ...................................................... 26Adjusting the Picture ......................................................... 29Adjustment feet ................................................................. 18Air filters ............................................................................ 49Aspect ratio ....................................................................... 23Automatic power shutoff function ..................................... 41Auto sync adjustment ....................................................... 35AUTO SYNC button........................................................... 35

BBackground ...................................................................... 39BACKLIGHT button ........................................................... 16

CCeiling-mount .................................................................... 22Ceiling+Rear ..................................................................... 43CINEMA ZOOM................................................................. 23Clock ................................................................................. 32CLR TEMP (Color Temperature) buttons........................... 30COMPONENT/RGB terminals ........................................... 14COMPUTER-RGB port ...................................................... 15

DDigital shift ........................................................................ 40DOT BY DOT ..................................................................... 23

EEconomy Mode ................................................................. 41ENTER button.................................................................... 9Exhaust ventilative hole..................................................... 4

FFocus ring ......................................................................... 17

GGAMMA button ................................................................. 25GUI (Graphical User Interface) ......................................... 26

IINPUT buttons ................................................................... 23

KKensington Lock ............................................................... 49KEYSTONE button ............................................................ 19

LLAMP REPLACEMENT indicator ....................................... 45Lens shift ........................................................................... 18

MMENU button..................................................................... 26

OOn-screen display............................................................. 37On-screen display Language ........................................... 43

PPhase ................................................................................ 32POWER buttons ................................................................ 17Power cord ........................................................................ 13POWER indicator .............................................................. 45Progressive Mode ............................................................. 31

RRear projection.................................................................. 22Remote control .................................................................. 11Remote control sensor ...................................................... 16Remote control signal transmitter ..................................... 11RESIZE button ................................................................... 23RS-232C Off Function ....................................................... 41RS-232C port .................................................................... 51

SSave Setting ...................................................................... 33Select Setting .................................................................... 33SIDE BAR .......................................................................... 23SMART STRETCH ............................................................. 23Status function .................................................................. 44STRETCH .......................................................................... 23Subtitle .............................................................................. 40S-VIDEO INPUT terminal ................................................... 13SXGA................................................................................. 24Sync .................................................................................. 35Sync on green ................................................................... 51

TTEMPERATURE WARNING indicator ................................ 45THEATER MODE button .................................................... 38Transmission Speed (RS-232C) ........................................ 42

UUNDO button .................................................................... 26

VVIDEO INPUT terminal ...................................................... 13Video System .................................................................... 37

WWired remote control input jack ........................................ 16

ZZoom knob ........................................................................ 17

No.3D DNR (3D Digital Noise Reduction) .............................. 36

XV-Z9000U Operation Manual - ProjectorCentral are two important reasons for prompt warranty...

Documents

Transcript of XV-Z9000U Operation Manual - ProjectorCentral are two important reasons for prompt warranty...