WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover...
Transcript of WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover...
![Page 2: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/2.jpg)
Issue Date:
Revision:
BGP-LSSDN Workshop
[Date]
[xx]
WSDN01_v0.1
![Page 3: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/3.jpg)
Overview
• In a nutshell• Motivations
• Introduction• BGP extensions
• Example• SR extensions• Extensions for BGP Egress Peer Engineering (EPE)
• Operational considerations
3
![Page 4: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/4.jpg)
4
In a nutshell
![Page 5: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/5.jpg)
SDN architectural framework
5
Application Plane
Application Service
Network Devices – IP/MPLS/Transport
Southbound Interfaces
REST/RESTCONF/NETCONF/XMPP
Control Plane
(controller)
Traffic Engineering
Route selection & failover
Resource Management
PCE-Pi2RS
SNMP MIBs OpenFlow YANG
Configuration
OpenFlowSNMP Netconf
Data Plane
BGP PCCRIBs
RSVP-TE
East/West-bound
interfaces –BGP
IPFIXForCES
Northbound Interfaces
Note: designations of north-bound and south-bound are relative to the control plane (“controller”)
Device & Resource Abstraction Layer (DAL)
Network Services Abstraction Layer
Segment Routing
Topology Discovery & Management
BGP-LS
![Page 6: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/6.jpg)
BGP-LS: in a nutshell…
6
Mechanism by which IGP link-state and traffic-engineering information is collected from networks and shared with external components using the BGP protocol
By using a new BGP NLRI encoding format and a new BGP-LS path attribute
For PCE, ALTO etc
What?
How?
Why?
![Page 7: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/7.jpg)
7
Motivations
![Page 8: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/8.jpg)
Complete topology visibility
• The contents of a router’s link-state database (LSDB) or traffic-engineering database (TED) only describes links and nodes within a single area
• End-to-end network visibility is important for certain applications:– End-to-end traffic-engineered paths that cross IGP areas or
autonomous systems (ASs)– Path Computation Element (PCE) function requires topology visibility
8
![Page 9: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/9.jpg)
MPLS-TE with PCE
• A Path Computation Element (PCE) can be used to compute MPLS-TE paths:
– within a “domain” (e.g. an IGP area)• May be used to provide greater computational capability, ability to impose additional
policy and more complex algorithms
– across multiple domains (such as a multi-area AS or multiple ASs)• Since the TED only includes information for a single area, routers cannot make
optimal decisions for constructing end-to-end traffic-engineered paths.• One solution to this problem is per-domain path computation (RFC5152). However,
it suffers from several limitations.
9
![Page 10: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/10.jpg)
Topology visibility for PCE
• There is no standards-defined mechanism mandated for a PCE to acquire network topology
• One option that is used by many implementations for the PCE is to use the services of a passive IGP listener
• BGP-LS provides an alternative option
10
![Page 11: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/11.jpg)
Challenges with using IGP listeners
• Controller needs to hear all IGP updates and therefore needs direct links to every area/domain in the network
• Operators tend to be uncomfortable with the approach of extending the IGP to external controllers
• Controllers need to support all relevant IGP protocols and extensions
11
![Page 12: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/12.jpg)
Advantages of using BGP
• Limited to a single protocol• BGP is already well-known and widely deployed; not a new
protocol• BGP has extensive policy mechanisms to control the
exchange of information and protect the network• BGP sessions between the controller and the BGP
speakers can be multi-hop i.e. there is no need for direct connectivity
• Route reflectors can be used to reduce the points of contact between the controller and the network
12
![Page 13: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/13.jpg)
TED synchronisation with PCE
13
Head-endnode Adjacent node
TED BGP speaker
Service request
Signaling protocol
Request/ response
PCE
TED synchronisation
mechanism: BGP-LS
![Page 14: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/14.jpg)
14
Introduction
![Page 15: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/15.jpg)
Router databases
15
Link-state database (LSDB) Traffic-engineering database (TED)
• Router IP addresses• Router link attributes:
• Neighbor router identifier• Local Interface IP address• Remote interface IP address• IP subnet address of link• IGP link metric
• Router IP addresses• Router link attributes:
• Local Interface IP address• Remote interface IP address• Traffic-engineering metric• Maximum bandwidth• Maximum reservable bandwidth• Unreserved bandwidth• Administrative group• Per-CoS reservation state• Pre-emption• SRLGs
![Page 16: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/16.jpg)
Advertising IGP info to consumers
16
BGP speaker BGP speaker BGP speaker. . .
IGP (LSDB, TED)
BGP speaker
Consumer
IGP (LSDB, TED) IGP (LSDB, TED)
LSDB, TED information mapped to
BGP-LS
User of the topology information
![Page 17: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/17.jpg)
BGP-LS peering example
17
PCE
N1
N2N9
N10N8
N4
N3N5
N6
N7
N11
N14
N12
N13
RR
BGP-LS speaker
BGP-LS speaker
BGP-LS speaker
![Page 18: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/18.jpg)
18
BGP extensions
![Page 19: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/19.jpg)
New BGP definitions
• New BGP link-state NLRI:– To describe link, node and prefixes corresponding to IGP link-state
data
• New BGP link-state path attribute:– Link, node and prefix properties and attributes (e.g. link metrics)
• Information carried by the new link-state NLRI and BGP-LS path attribute is represented in an IGP-neutral way as far as possible
![Page 20: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/20.jpg)
20
• Node NLRI• Link NLRI
• Prefix NLRILink-state NLRI
20
![Page 21: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/21.jpg)
MP-BGP attributes
21
• The MP-BGP attributes MP_REACH_NLRI and MP_UNREACH_NLRI are used for advertising BGP-LS information
16 bits
MP_REACH_NLRI (Type Code 14)Used to advertise feasible routes and next-
hop address
afi
safi next-hop length
address of nexthop(variable)
reserved
nlri (variable)
16 bits
MP_UNREACH_NLRI (Type Code 15)Used for withdrawing multiple unfeasible
routes
afi
safi
withdrawn routes (variable)
![Page 22: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/22.jpg)
Generic TLV format
• All information carried in the BGP-LS NLRI and path attribute uses this generic TLV format:
22
type length
32 bits16 bits16 bits
value (variable)
![Page 23: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/23.jpg)
Link-state NLRI
• Each link-state NLRI describes either a node, link or a prefix
• Non-VPN link, node and prefix information:– AFI: 16388, SAFI: 71
• VPN link, node and prefix information:– AFI: 16388, SAFI: 72
23
![Page 24: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/24.jpg)
Compatibility
• For two BGP speakers to exchange link-state NRLIs, they must have advertised their ability to do so via BGP Capabilities Advertisement.
• Capabilities Advertisement:– Capability code: 1 (MP-BGP)– AFI 16388 / SAFI 71 for BGP-LS– AFI 16388 / SAFI 72 for BGP-LS-VPN
24
![Page 25: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/25.jpg)
Link-state NLRI at a glance
25
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 26: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/26.jpg)
Link-state NLRI
26
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 27: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/27.jpg)
Link-state NLRI format (1)
27
nlri type total nlri length
32 bits16 bits16 bits
link-state nlri (variable)
Link-state NLRI (AFI 16388 / SAFI 71)Non-VPN link-state
nlri type total nlri length
32 bits16 bits16 bits
link-state nlri (variable)
route distinguisher Link-state NLRI (AFI 16388 / SAFI 72)VPN link-state
![Page 28: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/28.jpg)
Link-state NLRI format (2)
28
nlri type total nlri length
32 bits16 bits16 bits
link-state nlri (variable)
Link-state NLRI (AFI 16388 / SAFI 71)Non-VPN link-state
NLRI types
1 node nlri
2 link nlri
3 ipv4 topology prefix nlri
4 ipv6 topology prefix nlri
node nlri, link nlri or prefix nlri(see following slides)
![Page 29: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/29.jpg)
Node NLRI
29
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 30: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/30.jpg)
Node NLRI
30
protocol ID
32 bits16 bits16 bits
local node descriptors (TLVs)
Node NLRI (NLRI type = 1)
Protocol ID
1 IS-IS L1
2 IS-IS L2
3 OSPFv2
4 Direct
5 Static
6 OSPFv3
identifier
identifier
0 Default layer 3 routing topology
Identifies the IGP instance
![Page 31: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/31.jpg)
Link NLRI
31
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 32: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/32.jpg)
Link NLRI format
32
32 bits16 bits16 bits
local node descriptors (TLVs)
Link NLRI (NLRI type = 2)
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
Protocol ID
1 IS-IS L1
2 IS-IS L2
3 OSPFv2
4 Direct
5 Static
6 OSPFv3
identifier
0 Default layer 3 routing topology
Identifies the IGP instance
![Page 33: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/33.jpg)
Prefix NLRI
33
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 34: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/34.jpg)
IPv4 and IPv6 prefix NLRI format
34
32 bits16 bits16 bits
local node descriptors (TLVs)
IPv4 and IPv6 NLRI (NLRI type = 3 or 4)
identifier
protocol ID
prefix descriptors (TLVs)
Protocol ID
1 IS-IS L1
2 IS-IS L2
3 OSPFv2
4 Direct
5 Static
6 OSPFv3
identifier
0 Default layer 3 routing topology
Identifies the IGP instance
![Page 35: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/35.jpg)
Node identification
• Router identification:– OSPF uses 32-bit Router-ID (does not even have to be routable)– IS-IS uses a 48-bit ISO System ID
35
![Page 36: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/36.jpg)
Node descriptors
36
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 37: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/37.jpg)
Node descriptor TLVs
37
type=256 length
32 bits16 bits16 bits
node-descriptor sub-tlvs(variable)
Local Node DescriptorsNode descriptor for the local end of a link or the node itself• Mandatory for all three types of
NLRIs
type=257 length
32 bits16 bits16 bits
node-descriptor sub-tlvs(variable)
Remote Node DescriptorsNode descriptor for the node at the remote end of a link• Mandatory for Link NLRIs
![Page 38: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/38.jpg)
Node descriptor sub-TLVs
38
Type=256 or 257 length
32 bits16 bits16 bits
node-descriptor sub-tlvs(variable)
Sub-TLV code point Length Description Details
512 4 Autonomous System 32-bit ASN
513 4 BGP-LS identifier Uniquely identifies BGP-LS domain; combination of ASN and BGP-LS ID has to
be globally unique
514 4 Area-ID IGP area ID
515 variable IGP Router-ID Either a 6-octet ISO node-ID or 4-octet OSPF router-ID
![Page 39: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/39.jpg)
Link descriptors
39
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 40: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/40.jpg)
Link descriptor TLVs (1)
40
type length
32 bits16 bits16 bits
link-descriptor sub-tlvs(variable)
TLV code point Description Corresponding ISIS TLV/sub-TLV
258 Link Local/Remote Identifiers 22/4
259 IPv4 interface address 22/6
260 IPv4 neighbour address 22/8
261 IPv6 interface address 22/12
262 IPv6 neighbour address 22/13
263 Multi-topology identifier -
Link DescriptorUniquely identifies a link between multiple parallel links between a pair of routers.Actually a half-link: unidirectional logical link. The remote end advertises the other half.
Format and semantics of the value fields of these TLVs is identical to ISIS Extended IS Reachability sub-TLVs (RFC5305, RFC5307, RFC6119). A subset of these TLVs is present.
![Page 41: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/41.jpg)
Link descriptor TLVs (2)
type=258 length
32 bits16 bits16 bits
link local identifier
link remote identifier
Link Local/Remote Identifiers TLVUsed for unnumbered interfaces
type=259 length
32 bits16 bits16 bits
IPv4 interface address
IPv4 Interface Address TLV
type=260 length
32 bits16 bits16 bits
IPv4 neighbour address
IPv4 Neighbour Address TLV
![Page 42: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/42.jpg)
Link descriptor TLVs (3)
type=261 length
32 bits16 bits16 bits
IPv6 Interface Address TLVIPv6 interface address
type=262 length
16 bits16 bits
IPv6 Neighbour Address TLVIPv6 neighbour address
![Page 43: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/43.jpg)
Link descriptor TLVs (4)
type=263 length
32 bits16 bits16 bits
Multi-Topology ID 1
Multi-Topology ID TLVRRRR . . .
Multi-Topology ID nRRRR. . .
![Page 44: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/44.jpg)
Prefix descriptors
44
protocol ID
32 bits
local node descriptors (TLVs)
Node NLRI
identifier
32 bits
local node descriptors (TLVs)
Link NLRI
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
32 bits
local node descriptors (TLVs)IPv4 and
IPv6 NLRI
identifier
protocol ID
prefix descriptors (TLVs)
TLV Description
512 Autonomous System
513 BGP-LS identifier
514 Area-ID
515 IGP Router-ID
TLV Description
258 Link Local/Remote Identifiers
259 IPv4 interface address
260 IPv4 neighbour address
261 IPv6 interface address
262 IPv6 neighbour address
263 Multi-topology identifier
TLV Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
![Page 45: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/45.jpg)
Prefix descriptor TLVs (1)
45
type length
32 bits16 bits16 bits
link-descriptor sub-tlvs(variable)
TLV code point Description
263 Multi-topology identifier
264 OSPF route type
265 IP reachability information
Prefix DescriptorUniquely identifies an IPv4 or IPv6 prefix originated by a node
![Page 46: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/46.jpg)
Prefix descriptor TLVs (2)
type=263 length
32 bits16 bits16 bits
Multi-Topology ID 1
Multi-Topology ID TLVRRRR . . .
Multi-Topology ID nRRRR. . .
type=264 length
32 bits16 bits16 bits
route type
OSPF route type TLVIdentifies the OSPF route type of the prefix
Value Route Type
1 Intra-area
2 Inter-area
3 External 1
4 External 2
5 NSSA 1
6 NSSA 2
![Page 47: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/47.jpg)
Prefix descriptor TLVs (3)
type=265 length
32 bits16 bits16 bits
prefix length ip prefix (variable)
IP reachability information TLVContains one IP prefix originally advertised in the IGP
![Page 48: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/48.jpg)
Next-hop
• BGP-LS is supported over both IPv4 and IPv6 BGP sessions.
• Generally, the next-hop will be set to the local endpoint address of the BGP session
IF address_family(BGP session) = IPv6 THENaddress_family(next-hop in MP_REACH_NLRI) = IPv6_address
ELSE /* must be IPv4 */ address_family(next-hop in MP_REACH_NLRI) = IPv4_address
![Page 49: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/49.jpg)
49
• Node attribute TLVs• Link attribute TLVs
• Prefix attribute TLVs
Link-state Path Attribute
49
![Page 50: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/50.jpg)
BGP-LS attribute
• Optional, non-transitive BGP attribute• Attribute type value assigned by IANA is 29
• Carries link, node and prefix parameters and attributes corresponding to the nodes, links or prefixes carried in the link-state NLRI
• Attribute is only applicable when included with link-state NLRIs
50
![Page 51: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/51.jpg)
Link-state attribute
51
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
attribute flags
16 bits8 bits8 bits
node/link/prefix attribute TLVs(variable)
attribute type code = 29
BGP-LS Attribute (attr type = 29)
![Page 52: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/52.jpg)
Node attribute TLVs
• Node attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Node NLRI.
52
TLV code point Name Description263 Multi-topology
identifierCarries MT-IDs of all topologies where the node is reachable
1024 Node flag bits Overload, Attached, External, ABR, Router, V6 bites
1025 Opaque node attribute
Used for possible future IGP extensions not natively supported by BGP-LS
1026 Node name Symbol name (e.g. FQDN) of the router
1027 IS-IS area identifier All of the IS-IS areas a node is part of
1028 IPv4 router-ID of local node
Auxiliary router-ID that a node may be using e.g. for TE
1029 IPv6 router-ID of local node
Auxiliary router-ID that a node may be using e.g. for TE
![Page 53: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/53.jpg)
Link attribute TLVs (1)
• Link attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Link NLRI.
53
TLV code point Name Description1028 IPv4 router-ID of
local nodeAuxiliary router-ID that the local node may be using e.g. for TE
1029 IPv6 router-ID of local node
Auxiliary router-ID that the local node may be using e.g. for TE
1030 IPv4 router-ID of remote node
Auxiliary router-ID that the remote node may be using e.g. for TE
1031 IPv6 router-ID of remote node
Auxiliary router-ID that the remote node may be using e.g. for TE
1088 Admin group (colour) Bitmask of supported admin groups
1089 Max link bandwidth Maximum bandwidth of the link in this direction
1090 Max reservable link bandwidth
Maximum bandwidth of the link that can be reserved in this direction
![Page 54: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/54.jpg)
Link attribute TLVs (2)
• Link attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Link NLRI.
54
TLV code point Name Description1091 Unreserved
bandwidthAmount of bandwidth of the link that is available for reservation in this direction
1092 TE default metric TE metric for the link
1093 Link protection type Bitmask of supported protection types
1094 MPLS protocol mask Bitmask describing which MPLS protocolsare enabled: LDP, RSVP-TE
1095 IGP metric IGP metric for the link
1096 Shared risk link group
List of SRLG values
1097 Opaque link attribute Used for possible future IGP extensionsnot natively supported by BGP-LS
1098 Link name Symbol name (e.g. FQDN) for the link
![Page 55: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/55.jpg)
Prefix attribute TLVs
• Prefix attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Prefix NLRI.
55
TLV code point Name Description1152 IGP flags IS-IS up/down bit, OSPF “no unicast bit”,
OSPF “local address” bit, OSPF “propagate NSSA bit”
1153 IGP route tag Original IGP tags of the prefix
1154 IGP extended route tag
IS-IS extended route tags
1155 Prefix metric Metric of the prefix as known in the IGP topology
1156 OSPF forwardingaddress
OSPF forwarding address as known in the original OSPF advertisement
1157 Opaque prefix attribute
Used for possible future IGP extensions not natively supported by BGP-LS
![Page 56: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/56.jpg)
56
TLV Summary
56
![Page 57: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/57.jpg)
Summary: TLV codepoints (1)
57
TLV code point Description Usage
256 Local node descriptors Node NLRI, Link NLRI, Prefix NLRI
257 Remote nodedescriptors
Link NLRI
258 Link Local/remote identifiers
Link NLRI
259 IPv4 interface address Link NLRI
260 IPv4 neighbour address Link NLRI
261 IPv6 interface address Link NLRI
262 IPv6 neighbour address Link NLRI
263 Multi-topology identifier Link NLRI, Prefix NLRI, Link-stateattribute with node NLRI
264 OSPF route type Prefix NLRI
265 IP reachability information
Prefix NLRI
512 Autonomous System Remote/Local node descriptor TLVs
513 BGP-LS identifier Remote/Local node descriptor TLVs
514 Area-ID Remote/Local node descriptor TLVs
515 IGP Router-ID Remote/Local node descriptor TLVs
![Page 58: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/58.jpg)
Summary: TLV codepoints (2)
58
TLV code point Description Usage
1024 Node flag bits Link-state attribute with node NLRI
1025 Opaque node attribute Link-state attribute with node NLRI
1026 Node name Link-state attribute with node NLRI
1027 IS-IS area identifier Link-state attribute with node NLRI
1028 IPv4 router-ID of local node
Link-state attribute with node/link NLRI
1029 IPv6 router-ID of local node
Link-state attribute with node/link NLRI
1030 IPv4 router-ID of remote node
Link-state attribute with link NLRI
1031 IPv6 router-ID of remote node
Link-state attribute with link NLRI
1088 Admin group (colour) Link-state attribute with link NLRI
1089 Max link bandwidth Link-state attribute with link NLRI
1090 Max reservable link bandwidth
Link-state attribute with link NLRI
1091 Unreserved bandwidth Link-state attribute with link NLRI
![Page 59: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/59.jpg)
Summary: TLV codepoints (3)
59
TLV code point Description Usage
1093 Link protection type Link-state attribute with link NLRI
1094 MPLS protocol mask Link-state attribute with link NLRI
1095 IGP metric Link-state attribute with link NLRI
1096 Shared risk link group Link-state attribute with link NLRI
1097 Opaque link attribute Link-state attribute with link NLRI
1098 Link name Link-state attribute with link NLRI
1152 IGP flags Link-state attribute with prefix NLRI
1153 IGP route tag Link-state attribute with prefix NLRI
1154 IGP extended route tag Link-state attribute with prefix NLRI
1155 Prefix metric Link-state attribute with prefix NLRI
1156 OSPF forwarding address
Link-state attribute with prefix NLRI
1157 Opaque prefix attribute Link-state attribute with prefix NLRI
![Page 60: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/60.jpg)
60
Example
![Page 61: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/61.jpg)
OSPF network
61
lo1: 1.1.1.1/32 lo1: 2.2.2.2/32
lo1: 4.4.4.4/32lo1: 3.3.3.3/32
R1 R2
R4R3
10.0.0.1
10.0.0.3
10.0.0.2
10.0.0.4
10.1.2.1 10.1.2.2
10.3.4.3 10.3.4.4
10.1.3.1
10.1.3.3
10.2.4.2
10.2.4.4
Area 0.0.0.0
OSPF network design• Single area:0.0.0.0• All links identical• Default metrics • 4 point-to-point links• 1 broadcast interface on
each router• Router-ID is lowest
configured IP address• R4 is the DR for the
broadcast network
![Page 62: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/62.jpg)
OSPF link-state database
62
Router (type 1) LSAs
Network (type 2) LSAs
lo1: 1.1.1.1/32 lo1: 2.2.2.2/32
lo1: 4.4.4.4/32lo1: 3.3.3.3/32
R1 R2
R4R3
10.0.0.1
10.0.0.3
10.0.0.2
10.0.0.4
10.1.2.1 10.1.2.2
10.3.4.3 10.3.4.4
10.1.3.1
10.1.3.3
10.2.4.2
10.2.4.4
Area 0.0.0.0Link State
IDAdvertising
Router
1.1.1.1 1.1.1.1
2.2.2.2 2.2.2.2
3.3.3.3 3.3.3.3
4.4.4.4 4.4.4.4
Link StateID
AdvertisingRouter
10.0.0.4 4.4.4.4
Identical database on all nodes within the area
![Page 63: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/63.jpg)
R1’s router-LSA
63
Router (type 1) LSAslo1: 1.1.1.1/32 lo1: 2.2.2.2/32
lo1: 4.4.4.4/32lo1: 3.3.3.3/32
R1 R2
R4R3
10.0.0.1
10.0.0.3
10.0.0.2
10.0.0.4
10.1.2.1 10.1.2.2
10.3.4.3 10.3.4.4
10.1.3.1
10.1.3.3
10.2.4.2
10.2.4.4
Area 0.0.0.0Link State
IDAdvertising
Router
1.1.1.1 1.1.1.1
Type Link ID Link Data
Stub 1.1.1.1 255.255.255.255
Stub 10.1.2.0 255.255.255.0
Stub 10.1.3.0 255.255.255.0
Point-to-point
2.2.2.2 (neighbor router ID)
10.1.2.1 (intf addr)
Point-to-point
3.3.3.3 (neighbor router ID)
10.1.3.1 (intf addr)
Transit 10.0.0.4 (DR)
10.0.0.1 (intf addr)
# links: 6
![Page 64: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/64.jpg)
Introducing BGP-LS into the network
64
lo1: 1.1.1.1/32 lo1: 2.2.2.2/32
lo1: 4.4.4.4/32lo1: 3.3.3.3/32
R1 R2
R4R3
10.0.0.1
10.0.0.3
10.0.0.2
10.0.0.4
10.1.2.1 10.1.2.2
10.3.4.3 10.3.4.4
10.1.3.1
10.1.3.3
10.2.4.2
10.2.4.4
Area 0.0.0.0SDN
Controller
BGP session configured with
BGP-LS address family
OSPF LSDB exported to BGP
• At a minimum, only a single BGP speaker is required in each area (since all routers share the same LSDB)
BGP-LS NLRIs
![Page 65: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/65.jpg)
R1’s Link-state NLRIs (1)
65
Type Description
Node Local node descriptor
Type Description
Link Link to R2
Link Link to R3
Link Link to broadcast network
Type Description
Prefix 10.1.2.0/24
Prefix 10.1.3.0/24
Prefix 1.1.1.1/32
Router (type 1) LSAs
Link StateID
AdvertisingRouter
1.1.1.1 1.1.1.1
# links: 6
R1’s BGP-LS NLRIs
Type Link ID Link Data
Stub 1.1.1.1 255.255.255.255
Stub 10.1.2.0 255.255.255.0
Stub 10.1.3.0 255.255.255.0
Point-to-point
2.2.2.2 (neighbor router ID)
10.1.2.1 (intf addr)
Point-to-point
3.3.3.3 (neighbor router ID)
10.1.3.1 (intf addr)
Transit 10.0.0.4 (DR)
10.0.0.1 (intf addr)
![Page 66: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/66.jpg)
R1’s link-state NLRIs (2)
66
lo1: 1.1.1.1/32 lo1: 2.2.2.2/32
lo1: 4.4.4.4/32lo1: 3.3.3.3/32
R1 R2
R4R3
10.0.0.1
10.0.0.3
10.0.0.2
10.0.0.4
10.1.2.1 10.1.2.2
10.3.4.3 10.3.4.4
10.1.3.1
10.1.3.3
10.2.4.2
10.2.4.4
Area 0.0.0.0Type Description
Node Local node descriptor
Type Description
Link Link to R2
Link Link to R3
Link Link to broadcast network
Type Description
Prefix 10.1.2.0/24
Prefix 10.1.3.0/24
Prefix 1.1.1.1/32
![Page 67: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/67.jpg)
All link-state NLRIs (1)
• For each router:– 1 x Node NLRI– 3 x Link NLRIs:
• 2 for the point-to-point links• 1 for the broadcast network
– 3 x Prefix NLRIs• 2 for the point-to-point links• 1 for the loopback interface
– TOTAL: 28 link-state NLRIs
67
• For the broadcast network:– 1 x Node NLRI
• For the DR– 4 x Link NLRIs:
• For each DR to node adjacency– TOTAL: 5 link-state NLRIs
Total of 33 BGP-LS NLRIs generated for this OSPF network
![Page 68: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/68.jpg)
All link-state NLRIs (2)
68
Type Local Node Description
Node R1 Local node descriptor
Node R2 Local node descriptor
Node R3 Local node descriptor
Node R4 Local node descriptor
Node R4 (DR) Local node descriptor
Type Local Node Description
Link R1 Link to R2
Link R1 Link to R3
Link R1 Link to broadcast network (DR)
Link R2 Link to R1
Link R2 Link to R4
Link R2 Link to broadcast network (DR)
Link R3 Link to R1
Link R3 Link to R4
Link R3 Link to broadcast network (DR)
Link R4 Link to R2
Link R4 Link to R3
Link R4 Link to broadcast network (DR)
Link R4(DR) To R1
Link R4(DR) To R2
Link R4(DR) To R3
Link R4(DR) To R4
Type Local Node Description
Prefix R1 10.1.2.0/24
Prefix R1 10.1.3.0/24
Prefix R1 1.1.1.1/32
Prefix R2 10.1.2.0/24
Prefix R2 10.2.4.0/24
Prefix R2 2.2.2.2/32
Prefix R3 10.1.3.0/24
Prefix R3 10.3.4.0/24
Prefix R3 3.3.3.3/32
Prefix R4 10.2.4.0/24
Prefix R4 10.3.4.0/24
Prefix R4 4.4.4.4/32
![Page 69: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/69.jpg)
69
Extensions for Segment Routing
![Page 70: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/70.jpg)
Link-state attribute
70
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
attribute flags
16 bits8 bits8 bits
node/link/prefix attribute TLVs(variable)
attribute type code = 29
There is no change to the link-state NLRIs. Additional TLVs are defined for the BGP-LS attribute
BGP-LS Attribute (attr type = 29)
![Page 71: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/71.jpg)
SR: node attribute TLVs
• Node attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Node NLRI.
71
TLV code point Name Description1161 SID/Label Encodes a segment identifier (SID)
1034 SR capabilities Advertises the node’s SRGB
1035 SR algorithm List of SR algorithms supported
1036 SR local block Range of labels reserved for local SIDs
1037 SRMS preference SRMS preference for advertising router
![Page 72: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/72.jpg)
Link attribute TLVs
• Link attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Link NLRI.
72
TLV code point Name Description1099 Adjacency Segment
Identifier (Adj-SID)Includes an adjacency SID
1100 LAN Adjacency Segment Identifier
(Adj-SID)
Allows use of a single NLRI to announce all adjacencies on a LAN segmemt
1172 L2 Bundle Member Identifies L2 bundle member links associated with a parent L3 link
![Page 73: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/73.jpg)
Prefix attribute TLVs
• Prefix attribute TLVs that may be encoded in the BGP-LS path attribute when advertised together with a Prefix NLRI.
73
TLV code point Name Description1158 Prefix SID Advertises SID for a prefox
1159 Range Range of prefix to SID mappings
1170 IGP prefix attributes Routing protocol-specific flags
1171 Source router-ID IPv4 or IPv6 router-ID of the originator of the prefix
![Page 74: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/74.jpg)
74
Extensions for BGP Egress Peer Engineering (EPE)
![Page 75: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/75.jpg)
BGP peering segments
75
BGP Peering Segments• Segments identifying by a BGP EPE (Egress
Peer Engineering)-enabled node. • Enable the expression of source-routed inter-
domain paths
Peer Node SegmentsLocal (PeerNode-SID)
Segment representing a BGP peering node
Semantics:• SR header operation: NEXT• Next-hop: connected peering
node to which the segment is related
An ingress border router of an AS can steer a flow along a
selected AS, towards a selected egress border router
of the AS and through a specific peer by using BGP Egress Peer Engineering
capabilities
Peer Adjacency SegmentsLocal (PeerAdj-SID)
Segment representing an adjacency to a BGP peering node
Semantics:• SR header operation: NEXT• Next-hop: peer connected
through the interface to which the segment is related
Peer Set SegmentsLocal (PeerSet-SID)
Segment representing a set of BGP peering nodes
Semantics:• SR header operation: NEXT• Next-hop: load-balance across
any connected interface to any peer in the related group
![Page 76: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/76.jpg)
Link NLRI format
76
32 bits16 bits16 bits
local node descriptors (TLVs)
Link NLRI (NLRI type = 2)
identifier
protocol ID
remote node descriptors (TLVs)
link descriptors (TLVs)
Protocol ID
1 IS-IS L1
2 IS-IS L2
3 OSPFv2
4 Direct
5 Static
6 OSPFv3
7 BGP
identifier
0 Default layer 3 routing topology
Identifies the IGP instance
BGP-EPE segments describe links. Hence, the BGP-LS Link NLRI is used.
BGP-EPE-specific extension
![Page 77: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/77.jpg)
Node descriptor sub-TLVs
77
Type=256 or 257 length
32 bits16 bits16 bits
node-descriptor sub-tlvs(variable)
Sub-TLV code point Length Description Details
512* 4 Autonomous System 32-bit ASN
513* 4 BGP-LS identifier Uniquely identifies BGP-LS domain; combination of ASN and BGP-LS ID has to
be globally unique
514 4 Area-ID IGP area ID
515 variable IGP Router-ID Either a 6-octet ISO node-ID or 4-octet OSPF router-ID
516* 4 BGP Router-ID BGP router identifier
517 4 Confed Member ASN AS number of confederation member
BGP-EPE-specific extension
* mandatory for Link NLRI Local Node Descriptors
![Page 78: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/78.jpg)
Link-state attribute
78
afi=16388
safi=71/72next-hop length
address of nexthop(variable)
reserved
nlri (variable)
nlri type
nlri length
MP_REACH_NLRI Attribute
ORIGIN Attribute
AS-PATH Attribute
Link-State Attribute
. . .
BGP Update Message
attribute flags
16 bits8 bits8 bits
node/link/prefix attribute TLVs(variable)
attribute type code = 29
BGP-LS Attribute (attr type = 29)
TLV Name Description
1101 Peer-Node-SID Peer Node Segment Identifier (SID/index/label) + weight (for load-balancing)
1102 Peer-Adj-SID Peer Adjacency Segment Identifier(SID/index/label) + weight (for load-balancing)
1103 Peer-Set-SID Peer Set Segment Identifier(SID/index/label) + weight (for load-balancing)
BGP-EPE Link attribute TLVs
![Page 79: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/79.jpg)
Peer-Node-SID advertisement (1)
79
32 bits16 bits16 bits
local node descriptors (TLVs)
Link NLRI (NLRI type = 2)
identifier
remote node descriptors (TLVs)
link descriptors (TLVs)
protocol ID=7(BGP)
• Local BGP Router-ID of BGP-EPE enabled egress PE
• Local AS#• BGP-LS identifier
• Peer BGP Router-ID
• IPv4/v6 Interface Address: BGP session IPv4/IPv6 local address
• IPv4/v6 Neighbour Address: BGP session IPv4/IPv6 peer address
![Page 80: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/80.jpg)
Peer-Node-SID advertisement (2)
80
attribute flags
16 bits8 bits8 bits
SID/label/index (variable)
attribute type code = 29
BGP-LS Attribute (attr type = 29)
type=1101 length
32 bits16 bits16 bits
reserved
Peer-Node-SID TLV
flags weight
![Page 81: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/81.jpg)
Peer-Adj-SID advertisement (1)
81
32 bits16 bits16 bits
local node descriptors (TLVs)
Link NLRI (NLRI type = 2)
identifier
remote node descriptors (TLVs)
link descriptors (TLVs)
protocol ID=7(BGP)
• Local BGP Router-ID of BGP-EPE enabled egress PE
• Local AS#• BGP-LS identifier
• Peer BGP Router-ID
• Link Local/Remote identifiers
• IPv4/v6 Interface Address: BGP session IPv4/IPv6 local address
• IPv4/v6 Neighbour Address: BGP session IPv4/IPv6 peer address
![Page 82: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/82.jpg)
Peer-Adj-SID advertisement (2)
82
attribute flags
16 bits8 bits8 bits
SID/label/index (variable)
attribute type code = 29
BGP-LS Attribute (attr type = 29)
type=1102 length
32 bits16 bits16 bits
reserved
Peer-Adj-SID TLV
flags weight
![Page 83: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/83.jpg)
Peer-Set-SID advertisement
83
attribute flags
16 bits8 bits8 bits
SID/label/index (variable)
attribute type code = 29
BGP-LS Attribute (attr type = 29)
type=1103 length
32 bits16 bits16 bits
reserved
Peer-Set-SID TLV
flags weight
The Peer-Set-SID is advertised only as a BGP-LS attribute that is associated with Link NLRIs for Peer Node Segments or Peer Adjacency Segments that belong to the peer set.
![Page 84: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/84.jpg)
AS1
Example: BGP-EPE network
84
BGP EPE Controller
AS2
A
B
C
D G
AS3
F
K
E
AS4L/8
K/8
Node-SID: 32
Node-SID: 64
Node-SID: 16
Egress peer under consideration
![Page 85: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/85.jpg)
AS1
AS2
Example: BGP-EPE Segments
85
A
B
C
D G
AS3
F
K
E
AS4L/8
K/8
BGP EPE Controller
BGP Peering segments
allocated by PE C
Peer Node Segments
D 1012
E 1022
F 1052
Peer Adj Segments
Upper link to F 1032
Lower link to F 1042
Peer Set Segments
E, F 1060
C’s ILMIn Label
Op Out intf
1012 Pop Link to D
1022 Pop Link to E
1032 Pop Upper link to F
1042 Pop Lower link to F
1052 Pop Load balance on any link to F
1060 Pop Load balance on any link to E or F
BGP-LS NLRIs corresponding to
the BGP-EPE segments
Node-SID: 32
Node-SID: 64
Node-SID: 16
![Page 86: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/86.jpg)
Example: BGP-LS advertisements (1)
86
BGP Peering segments
allocated by PE C
Peer Node Segments
D 1012
E 1022
F 1052
Peer Adj Segments
Upper link to F 1032
Lower link to F 1042
Peer Set Segments
E, F 1060
Peer Node SID to D
Descriptors:Node: BGP-router-ID(C), AS1Peer: BGP-router-ID(D), AS2Link: IP address of C’s link to D, IP
address of D’s link to C
Attributes:PeerNode SID: 1012
Peer Node SID to E
Descriptors:Node: BGP-router-ID(C), AS1Peer: BGP-router-ID(E), AS3Link: IP address of C’s link to E, IP
address of E’s link to C
Attributes:PeerNode SID: 1022PeerSet SID: 1060
AS1
AS2A
B
C
D G
AS3F
K
E
AS4
![Page 87: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/87.jpg)
Example: BGP-LS advertisements (2)
87
BGP Peering segments
allocated by PE C
Peer Node Segments
D 1012
E 1022
F 1052
Peer Adj Segments
Upper link to F 1032
Lower link to F 1042
Peer Set Segments
E, F 1060
Peer Node SID to F
Descriptors:Node: BGP-router-ID(C), AS1Peer: BGP-router-ID(F), AS3Link: IP address of C’s loopback
used for multi-hop peering with F, IP address of F’s loopback used for multi-hop peering with C
Attributes:PeerNode SID: 1052PeerSet SID: 1060
AS1
AS2A
B
C
D G
AS3F
K
E
AS4
![Page 88: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/88.jpg)
Example: BGP-LS advertisements (3)
88
BGP Peering segments
allocated by PE C
Peer Node Segments
D 1012
E 1022
F 1052
Peer Adj Segments
Upper link to F 1032
Lower link to F 1042
Peer Set Segments
E, F 1060
Peer Adj SID – lower link to F
Descriptors:Node: BGP-router-ID(C), AS1Peer: BGP-router-ID(F), AS3Link: IP address of C’s lower link
to F, IP address of F’s lower link to C
Attributes:PeerAdj SID: 1042
Peer Adj SID – upper link to F
Descriptors:Node: BGP-router-ID(C), AS1Peer: BGP-router-ID(F), AS3Link: IP address of C’s upper link
to F, IP address of F’s upper link to C
Attributes:PeerAdj SID: 1032
AS1
AS2A
B
C
D G
AS3F
K
E
AS4
![Page 89: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/89.jpg)
89
Operational Considerations
![Page 90: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/90.jpg)
Operations (1)
• Unlike other BGP NLRIs, link-state NLRIs only carry application-level (i.e. topology) data which has no impact on forwarding state on BGP link-state speakers
• Intent is for dedicated route-reflectors to handle the distribution of this NLRI; not necessary for all routers to support this capability
90
![Page 91: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/91.jpg)
Operations (2)
• Recommended maximum rate for advertising/withdrawing link-state NLRIs is 200 updates per second
• Distribution of link-state information is recommended to be restricted to a single administrative domain (multiple areas or multiple ASs)
• Flow of updates is one-way-only: from BGP speakers to consumers; any updates from consumers need to be dropped
91
![Page 92: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/92.jpg)
92
References
![Page 93: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/93.jpg)
References• RFC4760
• RFC7752
• draft-ietf-idr-bgp-ls-segment-routing-ext-03
• draft-ietf-idr-bgpls-segment-routing-epe-13
• Using BGP-LS/PCE-P with XR and ODL (https://communities.cisco.com/community/developer/opendaylight/blog/2015/07/25/using-bgp-lspce-p-with-xrv-and-odl-or-cisco-osc)
93
![Page 94: WSDN01 - Module 4 - BGP-LS - v1 · (controller) Traffic Engineering Route selection & failover Resource Management i2RS PCE-P SNMP MIBs OpenFlow YANG Configuration Open Flow SNMP](https://reader036.fdocuments.net/reader036/viewer/2022071013/5fcb7e0651d137390b477cb2/html5/thumbnails/94.jpg)
Issue Date:
Revision:
Thank You !End of session
[Date]
[xx]
WSDN01_v0.1