Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez...
-
Upload
ada-preston -
Category
Documents
-
view
216 -
download
0
Transcript of Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez...
![Page 1: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/1.jpg)
Workshop 7:Thermal Steady State
Analysis of a Composite Slab
University of Puerto Rico at Mayagüez Department of Mechanical Engineering
Modified by (2008): Dr. Vijay K. GoyalAssociate Professor, Department of Mechanical EngineeringUniversity of Puerto Rico at Mayagüez
Thanks to UPRM students enrolled in INME 4058 sections 2006-08
![Page 2: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/2.jpg)
Scope
The purpose of this workshop is to demonstrate ANSYS capabilities in solving thermal problems. For this we will solve the steady state temperature field of a composite slab with a hole using the following prescribed geometry and boundary conditions:
![Page 3: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/3.jpg)
Geometry and Boundary Conditions
![Page 4: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/4.jpg)
Starting ANSYS
From your desktop:
Click on: START > All Programs >
ANSYS >
ANSYS Product Launcher.
Here we will set our Working Directory and the Graphics Manager
![Page 5: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/5.jpg)
Working Directory
This is the
10.0 ANSYS
Product Launcher
main window. Select the Working
Directory and type
the name of work
shop on Job Name.
![Page 6: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/6.jpg)
Click the button:
Customization/Preferences.
On the item of Use custom
memory settings type 128
on Total Workspace (MB):
and type 64 on
Database (MB):
Then click the Run
bottom.
Graphics Setup
* This setup applies to computers running under 512 MB of RAM* This setup applies to computers running under 512 MB of RAM
![Page 7: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/7.jpg)
This is ANSYS’s Graphical User Interface window.
ANSYS GUI Overview
![Page 8: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/8.jpg)
GUI Filtering
In order to maximize your workspace to meet your needs. Let’s filter out the GUI (Graphical User Interphase). Click on Preferences > Choose on GUI Filtering:
Thermal > OK.
![Page 9: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/9.jpg)
GUI Filtering
1 2
![Page 10: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/10.jpg)
Element Definition
For ANSYS to properly analyze the problem, we must choose well the appropriate element. We will choose Element Type Quad 4node 55:
![Page 11: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/11.jpg)
Element Definition
Element Type:
1. On Main Menu window, click Preprocessor > Element Type > Add/Edit/Delete
2. Click Add… on The Element Types Window
1
2
![Page 12: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/12.jpg)
Element Definition
3. On the Library of Element Type window select Quad 4node 55 > click OK > click Close on the Element Type window
plane55 will produce either quadrilateral or triangular elements for thermal analysis
3
![Page 13: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/13.jpg)
Material Properties
Now lets assign the thermal conductivity (k) for the two materials of this problem: Material 1 – KXX = 20 Material 2 – KXX = 50
![Page 14: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/14.jpg)
Material Properties
1. On the Main Menu Window select Preprocessor > Material Props > Material Model.
2. On the Material Model Behavior window select Material Model Number 1 > Thermal > Conductivity > Isotropic
3. On the Conductivity for Material Number 1 enter 20 for Thermal Conductivity KXX > click OK
2 3
![Page 15: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/15.jpg)
Material Properties
4. To add a second material: Click on the tab: Material > New Model > Define Material ID insert 2.
![Page 16: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/16.jpg)
Material Properties
Click on: Thermal > Conductivity > Isotropic > then on KXX insert the thermal conductivity of the second material (KXX = 50) > OK and close the Material window.
![Page 17: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/17.jpg)
Geometry
The strategy to produce the geometry is to create two rectangles (material 1 & 2) and remove a hole from the material 1
![Page 18: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/18.jpg)
Geometry
1. To create first rectangle, on the Main Menu Window select Preprocessor > Modeling > Create > Areas > Rectangle > By 2 Corners
2. On the Rectangle by 2 corners window enter WP X = 0 > WP Y = 0 > Width = 0.05 > Height = 0.05 > Click Apply
Note that all dimensions were converted to meters
1
2
![Page 19: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/19.jpg)
Geometry
3. To create the second rectangle repeat the process 2, using the following values:
WP X = .05
WP Y = 0
Width = .1
Height = .05
3
![Page 20: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/20.jpg)
Geometry
4. To create the circle, on the Main Menu Window select Preprocessor > Modeling > Create > Areas > Circle > Solid Circle
5. On the Solid Circular Area Window enter WP X = .025 > WP Y = .025 > Radius = .01 > Click OK
4
5
![Page 21: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/21.jpg)
Geometry
6. To create the hole select Preprocessor > Modeling > Operate > Booleans > Subtract > Areas
7. Click on the left rectangle > Click Ok on the Subtract Areas window
8. Click on the circle > Click OK again on the Subtract Areas window
7 86
![Page 22: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/22.jpg)
Geometry
9. To join the two rectangles, select Preprocessing > Modeling > Operate > Booleans > Glue > Area
10. On the Glue Areas window select Pick All \ OK
Now ANSYS know that the two rectangles are in contact, and make one big composite slab.
9
10
![Page 23: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/23.jpg)
Meshing
To make the finite element analysis we must first divide the object into small elements, this is called meshing.
![Page 24: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/24.jpg)
Meshing
1. On the Main Menu window, select Preprocessor > Meshing > Mesh Tool
2. On the Mesh Tool window Click on Smart Size > Select 5 > Select Mesh: Areas > Click on Set under Element Attributes
3. On the Meshing Attributes Window select Element Type number: 1 Plane 55 > Material number: 1 > click OK > Mesh > Click on the left rectangle
1
2
3
![Page 25: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/25.jpg)
Meshing
4. A screen like this will appear.
To view the two rectangles again go to Plot \ Areas
4
![Page 26: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/26.jpg)
Meshing
5. Repeat steps 1 through 3 selecting Material Number: 2 on the Meshing Attributes Window and Clicking on the right rectangle after selecting Mesh.
5
![Page 27: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/27.jpg)
Meshing
6. To see the mesh go to PlotCtrls \ Numbering
7. On the Plot Numbering Controls Window got to Elem/Attrib numbering \ select Material numbers \ Click OK
7
This should give you a color plot showing the areas and elements. Each element contains a number which refers to the material numbers we just set for each piece. The different material types are also denoted by the different colors.
![Page 28: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/28.jpg)
Boundary Conditions
Now we will apply the given boundary conditions for each side of the slab. Left Wall @ T = 200 Right Wall @ T = 50 Lower Wall is adiabatic Upper Wall has a h = 150 @ T = 25 Hole has a flux of q = 100
![Page 29: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/29.jpg)
Boundary Conditions (Temperature)
1. On ANSYS Main Menu Window select Preprocessing > Loads > Define Loads > Apply > Thermal > Temperatures > On Nodes
2. On the Apply TEMP on Nodes window Click on Box and draw a box around the left edge of the model to pick these nodes.
1
22
![Page 30: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/30.jpg)
Boundary Conditions (Temperature)
3. On the New Apply TEMP on Nodes window select DOFs to be constrained: Temp \ Apply as: Constant value \ Load Temp Value: 200
4. Repeat above procedure to apply the temperature boundary condition on the right boundary with a temperature of 50.
3
![Page 31: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/31.jpg)
Boundary Conditions (HT Coefficient)
1. On ANSYS Main Menu Window select Preprocessing > Loads > Define Loads > Apply > Thermal > Convection > On Nodes
2. On the Apply CONV on Nodes window Click on Box and draw a box around the top edge of the model to pick the nodes along the top edge.
1 2
![Page 32: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/32.jpg)
Boundary Conditions (HT Coefficient)
3. On the New Apply CONV on Nodes window select VALI Film coefficient\ enter h of 150 \ VAL2I Bulk Temperature \ 25 \ Click OK
3
![Page 33: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/33.jpg)
Boundary Conditions (Heat Flux)
1. On ANSYS Main Menu Window select Preprocessing > Loads > Define Loads > Apply > Thermal > Heat Flux > On Nodes
2. On the Apply HFLUX on Nodes window Click on Circle and draw a circle that catches the nodes around the hole.
1
2
![Page 34: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/34.jpg)
Boundary Conditions (Heat Flux)
3. On the New Apply HFLUX on Nodes window select VALUE Load HFLUX value\ enter 100 \ Click OK
3
Note: All geometry boundaries are adiabatic by default in ANSYS. So if you wish to apply symmetry or zero heat flux boundary conditions at any face of your model you have to do nothing to that face. We do not do any thing to the bottom edge of our model because it is an adiabatic surface by default.
![Page 35: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/35.jpg)
Display Settings
4. To see the boundary conditions on the model go to PlotCtrls \ Symbols
5. On Symbols windows go to Surface Load Symbols\ select Convect FilmCoef \ Show pres and convect as \ select Arrows \ Click OK
6. Repeat step 5 selecting Heat Flux instead of Convect FilmCoef
5
![Page 36: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/36.jpg)
FEM Solution
We are ready to start with the finite element analysis and obtain the temperature distribution across the slab.
![Page 37: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/37.jpg)
FEM Solution
1. On ANSYS Main Menu window select Solution > Solve > Current LS
1
![Page 38: Workshop 7: Thermal Steady State Analysis of a Composite Slab University of Puerto Rico at Mayagüez Department of Mechanical Engineering Modified by (2008):](https://reader036.fdocuments.net/reader036/viewer/2022062517/56649ef55503460f94c08f7e/html5/thumbnails/38.jpg)
Temperature Distribution
1. On ANSYS Main Menu Window select General Postproc > Plot Results > Vector Plot > Predefined
2. On the Vector Plot of Predefined Vectors window Click OK
2