Working with Common Plastics in the Woodshop
description
Transcript of Working with Common Plastics in the Woodshop
![Page 1: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/1.jpg)
Working with Common Plastics in the Woodshop
![Page 2: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/2.jpg)
Plastics have a Place in “High End” Work
Shelves for Built-Ins
Art Glass for Doors
Glazing for Art Frames
Display Cases
![Page 3: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/3.jpg)
Plastics Have Practical Uses in the Production
ShopSafety Shields and Guards
Guides and Slides
Push Sticks and Hold Downs
Shims and Spacers
![Page 4: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/4.jpg)
Working Plastics with ToolsYou Already Own
Sharp, clean bits and blades will provide very good results with most common tools.
Table saw, Router, Bandsaw , Sander and even Hand saws are effective tools.
![Page 5: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/5.jpg)
Friction causes melting , resulting in poor edge quality and “weld back”
Vibration and unsupported cuts can cause excessive tool marks and
chipping
Heat and Vibration are the Major Obstacles to Good
Results
![Page 6: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/6.jpg)
Many Plastics Can Be Easily Worked with Hand
Tools
![Page 7: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/7.jpg)
Drilling Requires Regrinding the Cutting Edge to Prevent “Self-feeding”
Flatten the back angle of the cutting edge
Achieve a scraping cut , rather than a digging one.
![Page 8: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/8.jpg)
Common Plastics:
Acrylic- Good optical properties, but brittle and more prone to breakageGlazing applications, signage, protective covers, tool sub-bases
![Page 9: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/9.jpg)
Common Plastics:
Acrylic- Good optical properties, but brittle and more prone to breakageGlazing applications, signage, protective covers, tool sub-bases
Polycarbonate- Lesser optical properties, highly impact resistantShields and guards, hold downs, tool sub-bases
![Page 10: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/10.jpg)
Common Plastics:
Acrylic- Good optical properties, but brittle and more prone to breakageGlazing applications, signage, protective covers, tool sub-bases
Polycarbonate- Lesser optical properties, highly impact resistantShields and guards, hold downs, tool sub-bases
Nylon, Polyethylenes- Opaque, flexible, good wear characteristicsSlides, runners, wear strips, push sticks, backers , tool sub-bases
![Page 11: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/11.jpg)
Common Plastics:
Acrylic- Good optical properties, but brittle and more prone to breakageGlazing applications, signage, protective covers, tool sub-bases
Polycarbonate- Lesser optical properties, highly impact resistantShields and guards, hold downs, tool sub-bases
Nylon, Polyethylenes- Opaque, flexible, good wear characteristicsSlides, runners, wear strips, push sticks, backers , tool sub-bases
PVC- Opaque, good adhesive properties, available in sizes and fittingsDC pipes and connectors, structural components
![Page 12: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/12.jpg)
Common Plastics:
Acrylic- Good optical properties, but brittle and more prone to breakageGlazing applications, signage, protective covers, tool sub-bases
Polycarbonate- Lesser optical properties, highly impact resistantShields and guards, hold downs, tool sub-bases
Nylon, Polyethylenes- Opaque, flexible, good wear characteristicsSlides, runners, wear strips, push sticks, backers , tool sub-bases
PVC- Opaque, good adhesive properties, available in sizes and fittingsDC pipes and connectors, structural components
Styrene/ABS- Opaque, good adhesive properties, very thin sheetsSpacers, shim stock, templates
![Page 13: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/13.jpg)
Cutting/Milling
Blades should be clean and sharp.
60-80 TPI seems to be optimal
ATB or “Triple Chip” grind scores edges before cuttingthrough
Zero-clearance inserts tosupport material
![Page 14: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/14.jpg)
Cutting/Milling
Fine tooth band saw bladeswill successfully cut plastics
Edge quality will be poor
Sanding or routing is an effective method for cleaning up the edges
![Page 15: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/15.jpg)
Cutting/Milling
Router bits are highly effective atcutting plastics
CNC machines can cut complexshapes in sheet plastics
Feed and RPM settings greatly effect edge quality. Pay attention to chip load.
Lower RPM with higher feed reduces friction heat and “melt-back”
![Page 16: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/16.jpg)
Cutting/Milling
Milling with hand routers is most effective when using templates
Band saw oversize, then trim to template
Spiral bits are highly effective, leaving few tool marks
Lower RPM with higher feed reduces friction heat and “melt-back”
![Page 17: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/17.jpg)
Hand Tools
Straight cuts in thinner plastics such as Acrylic or Styrene can be made by scoring a line and snapping the material very much like cutting glass.
![Page 18: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/18.jpg)
Hand Tools
Thin Styrene/ABS can be cut with a utility knife to complex shapes.
Thicker parts can be scored and snapped as described previously.
Hand saws can cut most plastics effectively.
![Page 19: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/19.jpg)
Dedicated Plastic Tooling
Saw Blades
Most manufactures make dedicated saw blades for plastics.
Look for 60-80 tooth Alternating top bevel or triple chip ground blades.
![Page 20: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/20.jpg)
Dedicated Plastic Tooling
Router Bits
Most manufactures make dedicated router bits for plastics.
“O-flute” bits have a concave inner face that curls the plastic chip reducing stress and chipping during the cut.
![Page 21: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/21.jpg)
Forming Plastics
“Soft” plastics like polycarbonate and styrene can be “cold formed” if thin enough.
A sheet metal brake can be used or the parts can be clamped in a vice and bent.
They will likely need to be over bent to account for spring back.
![Page 22: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/22.jpg)
Forming PlasticsAcrylic or thicker polycarbonates can be bent with heat.
Apply pressure in the bend direction and gently heat the bend area with a torch until the part softens enough to bend.
Overheating will result in bubbles appearing in the heated area.
![Page 23: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/23.jpg)
Forming Plastics
Many types of electric strip benders are available for bending plastics up to ¼ inch thick.
These heat the material slowly and safely to insure proper softening without over heating.
![Page 24: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/24.jpg)
Edge Polishing
Clear plastics parts may require polished edges.
Sand edges in successive grits to about 400
Use a buffing wheel with compound to polish the edges clear.
![Page 25: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/25.jpg)
Flame Polishing
A torch can produce a quick polished edge.
Sand to 220 grit
Pass flame quickly over the edge to very lightly melt the sanded surface
Parts can be stacked
Hydrogen/oxygen torch is most effective.
![Page 26: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/26.jpg)
Adhesives
Acrylics and polycarbonates
Can be glued to themselves using solvent cements such as IPS Weld-On
The parts need to be aligned and held with a consistent joint. The adhesive is then flowed into the joint using an artist’s brush or syringe applicator.
Capillary action causes the glue to fill the joint.
![Page 27: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/27.jpg)
PVC plastics can be glued together using common PVC cement available at any hardware store.
Styrenes and ABS plastics will bond together with common model maker’s glues from a hobby store.
Polyethylenes and nylons are impervious to virtually all adhesives and must be mechanically fastened.
Adhesives
![Page 28: Working with Common Plastics in the Woodshop](https://reader035.fdocuments.net/reader035/viewer/2022062501/56815b72550346895dc96a02/html5/thumbnails/28.jpg)
•Plastics Distributors in the local area
•For small quantities, online sources such as McMaster-Carr are excellent.
•Plastic saw blades and router bits can be sourced from your current suppliers.
•Specialty hand tools, adhesives and strip heaters for plastics are harder to source if you don’t have a plastics distributor locally. Sources are in the handout.
Sources