Our work supports teachers and administrators in preparing ...
Work Supports - vektek.com...10-0715-06 10-0815-06 0.92 1.00 0.58 2.36 For use with S/A fluid...
Transcript of Work Supports - vektek.com...10-0715-06 10-0815-06 0.92 1.00 0.58 2.36 For use with S/A fluid...
© Vektek, April 2019 800-992-0236 www.vektek.com
nAvailable in: 1,000, 2,500 and 4,000 lbs. nNormally retracted plungers do not interfere with part loading. Advance them with hydraulic pressure, exerting only spring force to bring the plunger into contact with your part. Hydraulic pressure then automatically sequences, “freezing” the plunger properly against the part. nVentless configuration and built in wiper keeps chips and debris out, reducing the chance of plunger/sleeve sticking or binding. nStainless steel plunger and sleeve assemblies help guard against corrosion in most machining environments.
Plunger and sleeve assemblies designed to help guard against corrosionin most machining environments.
Standard SAE porting and alternate O-Ring manifold face seal is located in the base of the support for bolt down in stal la tion. The base can be removed for direct cartridge mounting.
* Support capacities are listed at 5,000 psi maximum operating pressure. Support capacities for other pressures must be determined by consulting the capacity graph on the next page. ** Restrict flow rate to a maximum of 130 cu. in./minute. *** For cartridge mount models, see cavity dimensions on page B-31.
NOTE: The maximum system backpressure a fluid advance work support can overcome is 10 psi. Returning backpressure greater than 10 psi may cause slow or failed retraction.
ILS100700 REV P4000 lb.1000 & 2500 lb.
Model No.
Support Capacity
(lbs)
Mounting Style***
Contact Force**
(lbs)
Stroke(in)
Base Dimensions
(in.)
Retracted Height
(in.)
Oil Capacity**(cu. in.)
Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks.
10-0706-04 1,000Cartridge 1 - 6
0.25N/A
2.12 0.0810-0706-14 1,400 0.50 2.62 0.0910-0806-05 1,000
SAE/Manifold 1 - 60.25
0.90 X 1.31 X 1.752.51 0.16
10-0806-15 1,400 0.50 3.01 0.1710-0708-07 2,500
Cartridge 3 - 100.25
N/A2.83 0.12
10-0708-17 3,000 0.50 3.33 0.1410-0808-07 2,500
SAE/Manifold 3 - 100.25
1.25 X 1.50 X 2.313.25 0.19
10-0808-17 3,000 0.50 3.75 0.2110-0715-06
4,000Cartridge
8 - 12 0.50N/A 2.85 0.59
10-0815-06 SAE/Manifold 0.99 X 2.88 X 3.19 3.25 0.65
DimensionsModel No. A B C D E F G H J K L M N P Q R S T V W X Y Z AA˚ AB AC AD AE
Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks.10-0806-05
1-162.51 0.25 1.17
0.90 0.21 0.88 0.62 0.14 1.31 0.66 0.90 0.45 1.75 0.69 1.20 0.51 0.22 0.505/16-18 X 0.20
SAE 2 0.33 0.38 7 0.38 0.69 YES N/A10-0806-15 3.01 0.50 1.67 3/8 -24 x 0.2010-0808-07
1 1/4-163.25 0.25 1.35
1.25 0.36 1.13 0.81 0.19 1.50 0.75 1.06 0.53 2.31 0.94 1.66 0.72 0.28 0.63 7/16-14 X 0.25 SAE 4 0.43 0.38 N/A N/A N/A N/A YES10-0808-17 3.75 0.50 1.8510-0815-06 2 1/4-16 3.25 0.50 1.57 0.99 0.50 2.00 1.50 0.19 2.88 1.44 2.06 1.03 3.19 1.44 2.41 1.03 0.28 0.75 1/2-13 X 0.25 SAE 4 0.63 0.38 N/A N/A N/A N/A YES
B-29
Work Supports
Fluid Advance
www.vektek.com 800-992-0236 © Vektek, April 2019
All dimensions are in inches.
For proper sealing, mating surface must be flat within 0.003 in with a maximum 63 µ in.Ra surface finish.
Fluid Advance
1000 lb 1400 lb 2500 lb 3000 lb
Model No. Model No. Model No. Model No.
10-0706-04 10-0706-14 10-0708-07 10-0708-17
10-0806-05 10-0806-15 10-0808-07 10-0808-17
ILS100703 REV H
SUPP
ORT
FO
RCE
(lb)
0
INPUT PRESSURE (psi)5000
40003000
20001000
500
1000
1500
2000
2500
3000
10-0715-06
10-0815-06
ILS100704 REV E
05000
40003000
20001000
4000
3000
2000
1000
SUPP
ORT
FO
RCE
(lb)
INPUT PRESSURE (psi)
DimensionsModel No. A B C D E F G H J K L M N P Q R S T V W X Y Z AA˚ AB AC AD AE
Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks.10-0806-05
1-162.51 0.25 1.17
0.90 0.21 0.88 0.62 0.14 1.31 0.66 0.90 0.45 1.75 0.69 1.20 0.51 0.22 0.505/16-18 X 0.20
SAE 2 0.33 0.38 7 0.38 0.69 YES N/A10-0806-15 3.01 0.50 1.67 3/8 -24 x 0.2010-0808-07
1 1/4-163.25 0.25 1.35
1.25 0.36 1.13 0.81 0.19 1.50 0.75 1.06 0.53 2.31 0.94 1.66 0.72 0.28 0.63 7/16-14 X 0.25 SAE 4 0.43 0.38 N/A N/A N/A N/A YES10-0808-17 3.75 0.50 1.8510-0815-06 2 1/4-16 3.25 0.50 1.57 0.99 0.50 2.00 1.50 0.19 2.88 1.44 2.06 1.03 3.19 1.44 2.41 1.03 0.28 0.75 1/2-13 X 0.25 SAE 4 0.63 0.38 N/A N/A N/A N/A YES
B-30
Work Supports
Fluid Advance
© Vektek, April 2019 800-992-0236 www.vektek.com
Cavity Check List √Confirm capacity of item selected.
Note the sealing surface finish requirements.
Minimum depth specification represents the nominal depth of the standard Vektek base dimension.
Confirm cavity drawing is appropriate for the model number used.
Note specified thread depth when cutting threads.
When using a bottoming tap tool, modifications may be required.
When hand tapping threads, perpendicularity is essential.
Cartridge DimensionsModel No. A B C D E F G H J M V W
10-0706-041-16
2.12 0.25 1.680.24 0.21 0.88 0.62 0.14 0.92 0.50
5/16-18 X 0.203/8-24 X 0.2010-0706-14 2.62 0.50 2.18
10-0708-071 1/4-16
2.83 0.25 2.170.31 0.36 1.13 0.81 0.19 1.17 0.63 7/16-14 X 0.25
10-0708-17 3.33 0.50 2.67
10-0715-06 2 1/4-16 2.85 0.50 2.16 0.19 0.50 2.00 1.50 0.19 2.16 0.75 1/2-13 X 0.25
Work Supports
Fluid Advance Cartridges
B-31
www.vektek.com 800-992-0236 © Vektek, April 2019
.150 MIN.
.281 MAX. THRU TO FLUID PASSAGEANYWHERE ON OR INSIDE A .50" RADIUS
R.50
R.60.590 (REF).150(REF)
R.020MAX.
.090(REF)
.090±.016
2.165(REF)
2.189(REF)
.63 x .09 DEEPANYWHERE ON A .60" RADIUS
-A-2.165 .001
.590 MIN (THREAD DEPTH).150 .020
ILS100707 REV H
WORK SUPPORT CAVITY DIMENSIONS:#4000 SINGLE ACTING FLUID ADVANCE10-0715-06(TORQUE TO 100 Ft.Lbs.)
SEE DETAIL A
2.189±.007 x .090±.016THREAD 2 1/4-16 UN X .150±.020WITH Ø 2.27 X 45° CHAMFER
.002 -A-
Ø.125 DRILL THRUTO Ø.281 HOLE
.002 -A-.002
DETAIL A
63
Work Supports
Fluid Advance Cartridge Cavities
B-32
© Vektek, April 2019 800-992-0236 www.vektek.com
D
B
C
ATHREADS
ILS309800 REV D
SAE 4
B
C
A
ILS100708 REV G
D
Fluid Advance Work Support Shields
Model No. Work SupportModel No. A B C D
For use with fluid advance Work Supports only
81-0707-01
10-0706-0410-0706-1410-0806-0510-0806-15
10-0706-10 10-0806-10 10-0806-20
10-0706-10-PS 10-0806-20-PS
0.66 0.50 0.30 1.04
81-0708-01
10-0708-0710-0708-1710-0808-0710-0808-17
10-0708-10 10-0808-10 10-0808-20
10-0708-10-PS 10-0808-20-PS
0.85 0.84 0.43 1.38
81-0715-0110-0715-0610-0815-06
0.92 1.00 0.58 2.36
B Threaded hole
for Work Support
CFeeder Cap or
Lock Nut
ILS100709 REV D
A
.001
.002 A
Feeder Caps DimensionsModel No. A B C D
For use with fluid advance Work Supports only30-9872-39 3/4-16 UN .85 .38 1.0030-9872-40 1-16 UN 1.00 .53 1.2530-9872-43 1 1/4-16 UN 1.38 .85 1.5030-9872-46 1 3/4-16 UN 1.47 1.00 2.0030-9872-47 2 1/4-16 UN .99 .59 2.50
Work Support Capacity B C Lock
Nut1000 HC 3/4-16 1.16 N/A
1000/1400/2000 HC 1-161 1.44 N/A2500/3000/4000 HC 1 1/4-161 1.73 64-0012-00
8000 HC 1 3/4-16 2.31 N/A4000 2 1/4-16 2.89 64-0022-00
Machining Specications for Work Supports mounted with a Feeder Cap or Lock Nut
Work Supports
Fluid Advance Accessories
B-33
www.vektek.com 800-992-0236 © Vektek, April 2019
Gauge
SEQ/PRVCombo Valve
Power PinHydraulicCrowder
Fluid Advance
Work Support
TuffCam™ Top FlangeSwing Clamp
Power PinHydraulicCrowderTuffCam™ Top Flange
Swing Clamp
TuffCam™ BottomFlange Swing Clamp
TuffCam™ BottomFlange Swing Clamp
Fluid Advance
Work Support
PRV Assembly
Gauge
SequenceValve
ThreadedCylinder
ThreadedCylinder
SequenceValve
Model No.
Capacity(lbs)
O-Ring Part No. A B C D E
10-0704-1010-0804-20
1,000(High Capacity)
39-0511-72.185 x .039
.297 .141 .187 .040 1/4-20 UNC-2A
10-0706-04 10-0806-05
1,000(Std. Stroke)
39-0510-59 .236 x .059
.384 .197 .238 .047 5/16-18 UNC-2A
10-0706-14 10-0806-15
1400(Long Stroke)
39-0000-69 .301 x .064
.450 .197 .302 .047 3/8-24 UNF-2A
10-0706-1010-0806-10 10-0806-20
2000(High Capacity)
39-0510-59.236 x .059
.384 .197 .238 .047 5/16-18 UNC-2A
10-0706-1610-0806-1610-0806-26
2,000(Long Stroke
HC)
39-0510-59.236 x .059
.384 .197 .238 .047 5/16-18 UNC-2A
10-0708-0710-0808-07
2,500(Std. Stroke)
55-2500-05.301 x .070
.493 .250 .328 .070 7/16-14 UNC-2A
10-0708-17 3,000 (Long Stroke)
55-2500-05 .301 x .070
.493 .250 .328 .070 7/16-14 UNC-2A10-0808-17
10-0708-1010-0808-1010-0808-20
4,000(High Capacity)
55-2500-05.301 x .070
.493 .250 .328 .070 7/16-14 UNC-2A
10-0708-1610-0808-1610-0808-26
4,000(Long Stroke
HC)
55-2500-05.301 x .070
.493 .250 .328 .070 7/16-14 UNC-2A
10-0715-0610-0815-06
4,00039-0020-09.364 x .070
.555 .250 .390 .070 1/2-13 UNC-2A
10-0710-1010-0810-20
8,000(High Capacity)
39-0511-76.472 x .079
.681 .313 .508 .080 5/8-11 UNC-2A
D .005A MIN.
B .010C .003
60
R.020 MAX.
ILS100714 REV G
SELF-PRODUCEDCONTACT BOLT
WORK SUPPORTPLUNGER
O-RING SEAL
E, THREAD
Self-Produced Contact Bolt for Single ActingFluid Advanced Work Support
Work Supports
Fluid Advance Accessories
B-34
Vektek Concept