WORK MATERIAL TAP SELECTION CHART - OSG UK...
2
NAME SPECIFICATION THREAD DESIGNATION CC-POT Spiral point, chip control general applcations. Available in DiN series & long series METRIC, METRIC FINE, CC-SFT Spiral flute, chip control general applications. Available in DiN series & long series METRIC, METRIC FINE, UNJC, UNJF & G(BSP) VA-POT Spiral point, general applications METRIC, METRIC FINE, UNC, UNF, METRIC (6G), UNJC & UNJF VA-SFT Spiral flute, general applications METRIC, METRIC FINE, UNC, UNF, METRIC 6G, UNJC & UNJF CC-NEO-SFT Variable lead spiral flute, chip control for stainless steel applications. METRIC S-XPF Fluteless, high performance, Din series & long series. Oil hole version avaialbe. METRIC & METRIC FINE 6HX & METRIC 6GX & 7GX Z-POT Spiral point, for high speed tapping (through coolant version available) METRIC & METRIC FINE Z-SFT Spiral flute, for high speed tapping (through coolant version available) METRIC & METRIC FINE VPO-H-POT Spiral point, for steels 25 ~ 45 HRC (non-through coolant version available) METRIC VPO-H-SFT Spiral flute, for Steels 25 ~ 45 HRC (non-through coolant version available) METRIC WHR-Ni-POT Spiral point, HR coated for heat resistant alloys such as INCONEL ® 718 METRIC, UNJC & UNJF WHR-Ni-SFT Spiral flute, HR coated for heat resistant alloys such as INCONEL ® 718 METRIC, UNJC & UNJF V-Ti-POT Spiral point, for titanium alloys (Ti-6AI-4V), 40~45HRC METRIC, UNJC & UNJF V-Ti-SFT Spiral flute, for titanium alloys (Ti-6AI-4V), 40~45HRC METRIC, UNJC & UNJF VP-DC-MT Straight flute, for cast iron (through coolant version available) METRIC & METRIC FINE E-HL-POT Wire Insert spiral point, for heat resistant alloys such as Inconel ® 718 METRIC, UNJC & UNJF E-HL-SFT Wire Insert spiral flute, for heat resistant alloys such as Inconel ® 718 METRIC, UNJC & UNJF CC-HL-SFT Wire Insert spiral flute, chip control, general applications METRIC & UNJF OIL-C-MT Super high speed tapping in cast iron 100m/min with synchro feed (oil hole). METRIC WH-55-OT For heat treated steels 40~55HRC METRIC WX-PNC Carbide thread mill, general applications METRIC, UNIFIED, Rc(BSPT) & NPT Excellent Good WORK MATERIAL NEW NEW NEW NEW NEW Low Carbon steel Cast steel Cast Iron Ductile cast Iron Brass casting Copper Brass Bronze Aluminium alloy casting Aluminium rolled Titanium alloy Nickel alloy Magnesium alloy Zinc alloy casting Bakelite / Phenol Vinyl / Nylon Medium carbon steel High Carbon steel Alloy steel Hardened steel Tool steel Stainless steel C0.25% C0.25% ~0.45% C0.45% < SCM 25~35 HRC 35~45 HRC 40~555 HRC 52~65 HRC SUS SKD SC GG GGG Cu Bs BsC PB Al AC ADC MC ZDC Ti Ni 15~24 8~13 15~30 15~25 10~25 10~15 7~12 15~30 15~25 10~25 8~13 6~9 15~30 15~25 10~25 8~13 6~12 10~15 7~12 15~30 8~20 8~20 3~5 3~5 5~20 6~15 8~16 7~12 5~15 8~20 8~20 10~15 7~11 10~15 7~14 15~30 12~17 7~14 10~30 15~25 15~35 10~20 10~20 16~30 16~30 15~40 20~50 20~40 15~35 20~40 20~40 15~35 15~35 15~35 10~30 15~35 15~35 10~15 5~10 4~6 3~5 2~4 1~3 10~20 10~20 CPM CPM HR HR 15~30 30~40 15~30 6~10 15~60 15~40 25~70 25~70 25~70 2~4 1~3 1~4 40~80 40~65 50~100 50~100 50~100 50~65 65~130 50~100 65~130 50~100 65~130 50~100 65~130 50~70 50~100 65~130 50~100 65~130 50~100 65~130 20~60 20~60 65~130 65~130 50~75 40~65 40~65 40~65 15~30 30~40 8~13 15~30 6~10 8~8 6~10 4~8 7~10 6~12 10~15 7~12 4~6 3~5 2~4 1~3 15~20 15~40 6~10 15~30 15~30 30~40 8~13 15~30 15~35 6~10 15~24 15~25 15~25 10~25 10~25 15~30 15~40 TAP SELECTION CHART OSG UK Limited Tel : +44 (0)845 305 1066 Fax: +44 (0)845 305 1067 web: uk..osgeurope.com e-mail: [email protected] OSG UK Limited, Shelton House, 5 Bentalls, Pipps Hill Industrial Estate, Basildon, Essex, England, SS14 3BY V (Composite multi layered) coating, OX (steam oxide) treatment, CrN (Chromium Nitride) coating, WX (TiAlN) coating HSSE (High Vanadium) HSS-EV3, PM (Powder Metallurgy (Co5 + V5), HSS-Co (HSS Colbalt-Co8), Carbide (Tungsten carbide) MATERIAL COATING CHAMFER NEW NEW NEW NEW NEW
Transcript of WORK MATERIAL TAP SELECTION CHART - OSG UK...
NAME SPECIFICATION THREAD DESIGNATION
CC-POT Spiral point, chip control general applcations.Available in DiN series & long series METRIC, METRIC FINE,
CC-SFT Spiral flute, chip control general applications.Available in DiN series & long series
METRIC, METRIC FINE, UNJC, UNJF & G(BSP)
VA-POT Spiral point, general applicationsMETRIC, METRIC FINE, UNC, UNF, METRIC (6G), UNJC & UNJF
VA-SFT Spiral flute, general applicationsMETRIC, METRIC FINE, UNC, UNF, METRIC 6G, UNJC & UNJF
CC-NEO-SFT Variable lead spiral flute, chip control for stainless steel applications. METRIC
S-XPF Fluteless, high performance, Din series & long series. Oil hole version avaialbe.
METRIC & METRIC FINE 6HX & METRIC 6GX & 7GX
Z-POT Spiral point, for high speed tapping(through coolant version available) METRIC & METRIC FINE
Z-SFT Spiral flute, for high speed tapping(through coolant version available) METRIC & METRIC FINE
VPO-H-POT Spiral point, for steels 25 ~ 45 HRC(non-through coolant version available) METRIC
VPO-H-SFT Spiral flute, for Steels 25 ~ 45 HRC(non-through coolant version available) METRIC
WHR-Ni-POT Spiral point, HR coated for heat resistant alloys such as INCONEl® 718 METRIC, UNJC & UNJF
WHR-Ni-SFT Spiral flute, HR coated for heat resistant alloys such as INCONEl® 718 METRIC, UNJC & UNJF
V-Ti-POT Spiral point, for titanium alloys (Ti-6AI-4V), 40~45HRC METRIC, UNJC & UNJF
V-Ti-SFT Spiral flute, for titanium alloys (Ti-6AI-4V), 40~45HRC METRIC, UNJC & UNJF
VP-DC-MT Straight flute, for cast iron(through coolant version available) METRIC & METRIC FINE
E-HL-POT Wire Insert spiral point, for heat resistant alloys such as Inconel® 718 METRIC, UNJC & UNJF
E-HL-SFT Wire Insert spiral flute, for heat resistant alloys such as Inconel® 718 METRIC, UNJC & UNJF
CC-HL-SFT Wire Insert spiral flute, chip control,general applications METRIC & UNJF
OIL-C-MT Super high speed tapping in cast iron100m/min with synchro feed (oil hole). METRIC
WH-55-OT For heat treated steels 40~55HRC METRIC
WX-PNC Carbide thread mill, general applicationsMETRIC, UNIFIED, Rc(BSPT) & NPT
Excellent GoodWORK MATERIAL
NEW
NEW
NEW
NEW
NEW
low
Car
bon
stee
l
Cas
t ste
el
Cas
t Iro
n
Duc
tile
cast
Iron
Bra
ss
cast
ing
Cop
per
Bra
ss
Bro
nze
Alu
min
ium
allo
y ca
stin
g
Alu
min
ium
rolle
d
Tita
nium
allo
y
Nic
kel a
lloy
Mag
nesi
um
allo
y
Zinc
allo
y ca
stin
g
Bak
elite
/ P
heno
l
Viny
l / N
ylon
Med
ium
carb
on s
teel
Hig
h C
arbo
nst
eel
Allo
y st
eel
Har
dene
dst
eel
Tool
ste
el
Sta
inle
ssst
eel
C0.25% C0.25%~0.45%
C0.45%< SCM 25~35
HRC35~45HRC
40~555HRC
52~65HRC SUS SKD SC GG GGG Cu Bs BsC PB Al AC
ADC MC ZDC Ti Ni
15~24
8~13
15~30
15~25
10~25
10~15
7~12
15~30
15~25
10~25
8~13
6~9
15~30
15~25
10~25
8~13
6~12
10~15
7~12
15~30
8~20
8~20
3~5
3~5
5~20
6~15
8~16
7~12
5~15
8~20
8~20
10~15
7~11
10~15
7~14
15~30
12~17
7~14
10~30
15~25
15~35
10~20 10~20
16~30
16~30
15~40
20~50
20~40
15~35
20~40
20~40
15~35
15~35
15~35
10~30
15~35
15~35
10~15
5~10
4~6
3~5
2~4
1~3
10~20
10~20
CPM
CPM
HR
HR
15~3030~40 15~30 6~10
15~60 15~40 25~70 25~70 25~70
2~4
1~3
1~4
40~80 40~65
50~100
50~100
50~100
50~65 65~130
50~100
65~130
50~100
65~130
50~100
65~130 50~70
50~100
65~130
50~100
65~130
50~100
65~130 20~60 20~60 65~130 65~13050~75 40~65 40~65 40~65
15~3030~40 8~13 15~30
6~10
8~8
6~10
4~8
7~10
6~12
10~15
7~12
4~6
3~5
2~4
1~3
15~20
15~406~10 15~3015~3030~40 8~13 15~30
15~356~10 15~2415~2515~25 10~25 10~25
15~30 15~40
TAP SELECTION CHART OSG UK Limited
Tel : +44 (0)845 305 1066 Fax: +44 (0)845 305 1067 web: uk..osgeurope.com e-mail: [email protected] UK limited, Shelton House, 5 Bentalls, Pipps Hill Industrial Estate, Basildon, Essex, England, SS14 3BYV (Composite multi layered) coating, OX (steam oxide) treatment, CrN (Chromium Nitride) coating, WX (TiAlN) coating
HSSE (High Vanadium) HSS-EV3, PM (Powder Metallurgy (Co5 + V5), HSS-Co (HSS Colbalt-Co8), Carbide (Tungsten carbide)
MATERIAL COATING CHAMFER
NEW
NEW
NEW
NEW
NEW
SCM SUS SKDSKS GG GGG Cu Al AC Ti
Excellent GoodWORK MATERIAL
DRILL SELECTION CHART NAME SPECIFICATION ≤2D ≤3D ≤4D ≤5D ≤8D
MRS-GDL Micro drill for stainless steels 0.5~3
WX-MS-GDS Stub, precision processing 0.2~5
WD-2D / 4D General applications 2.0~20
WDO-3D / 5D low thrust, through coolant 2.8~20
TRS-3D / 5D & 10D
3 Flute through coolant for ultra fast processing
5.018.5
D-STAD Diamond coated carbide drill for composite materials
4.8649.55
WDO-10D / 15D20D & 30D
Non-step through coolant 10D, 15D, 20D & 30D 2~12
CAO-GDXL Non-step through coolant 3~10
HYP-HP-GDS Stub, for general applications 3~20
HYP-HPO-GDS Stub, through coolant 3~20
HYP-HPO-GDN Medium, through coolant 3~16
HYP-HPO-GDR Regular, through coolant 5~16
NEXUS-GDS Stub, for high speed drilling 1~12
NEXUS-GDR Regular, for high speed drilling 2~12
EX-SUS-GDS Stub, for stainless and aluminium 0.5~20
EX-SUS-GDR Regular, for stainless and aluminium 2~20
TDXL Non step, 10D, 15D and 20D 1.6~12
VPH-GDS Stub, for hardened steels 0.5~20
CRM Carbide straight reamer0.3
13.03
≤10D ≤15D ≤20D ≤30D
Tool
ste
el
Cas
t Iro
n
Duc
tile
cast
Iron
Cop
per
Alu
min
ium
Alu
min
ium
allo
y ca
stin
g
Tita
nium
Tita
nium
allo
y
Inco
nel®
Com
posi
tem
ater
ial
Mag
nesi
um
allo
y
low
car
bon
stee
l
Med
ium
carb
on s
teel
Hig
h ca
rbon
stee
l
Allo
y st
eel
Har
dene
dst
eel
Que
nche
d an
d
tem
pere
dst
eel
Sta
inle
ssst
eel
NEW
NEW
NEW
NEW
NEW
OSG UKTool refurbishment service
SC Smooth coating, WX (TiAlN) coating, FX (TiAlN) coating, TiAlN (Titanium Aluminium Nitride) coating,TiN (Titanium Nitride) coating, WXl coating for excellent lubricity and abrasion resistance,WD1 coating
HSSE (High Vanadium) HSS-EV3, XPM ( High Grade Powder Metallurgy , HSS-Co (HSS Colbalt-Co8), Carbide (Tungsten carbide)
Authorised Distributor
OSG UK LimitedMATERIAL COATING RANGE < 35
HRC35~45HRC
45~50HRC
50~62HRC
62~70HRC
C0.25% C0.25%~0.45%
C0.45%< CFRP
