WITTUR GM.2.001049.EN.01

No part of this publication may be reproduced or translated,even in part, without prior written permission from WITTUR. Copyright WITTUR 2015Subject to change without notice!URL: http://www.wittur.come-mail: info@wittur.comCodeVersionGM.2.001049.ENHCodeVersionDate3212.32.0230J20.01.2015AUTOMATIC DOORSFINELINETy 01-02/CTy 11-12/R-LTy 4A Ty 4ASSubject to change without notice!CodeVersionGM.2.001049.ENHCodeVersionDate3212.32.0230J20.01.2015JGeneral up-dating20/01/15IGeneral up-dating10/02/14HUp-dated document's Lay-out and the following points: 1.8.1; 1.8.2; 1.8.3; 1.8.4; 1.8.5.05/04/13MOD. DESIGNATION DATEEnglish from Pg. 1 to 76 / INSTRUCTION HANDBOOK LANDING DOOREnglish from Pg. 77 to 164 / INSTRUCTION HANDBOOK CAR DOORENENINSTRUCTION HANDBOOK LANDING DOORINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20151.164LANDING DOORINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20152.164SYMBOLS USEDINDEXSymbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Foreword and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51.1 General description: Ty 4AS, Ty 4S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51.2 General description: Ty 01/C, Ty 11/R-L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61.3 Landing door alignment with car door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71.4 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91.5 Positioning of the landing door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101.6 Assembly of the sill. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131.7 Assembly of the frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151.8 Assembly of the mechanism cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171.9 Assembly of the top track. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181.10 Assembly of door panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301.11 Assembly of the emergency opening device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .351.12 Emergency opening contact (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .361.13 Assembly of the closing weight rope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .371.14 Toe guard assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .391.15 Placing the mechanisms on the thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .401.16 Assembly of the panel buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .411.17 Assembly of the lintel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .431.18 Door contact cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451.19 Instruction on how to keep the doors in good operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .461.20 Testing the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .472. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .512.1 Replacement of the sliding shoes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .512.2 Replacement of the roller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .522.3 Replacement of the synchronisation rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .542.4 Replacement of the window glasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .562.5 Checking the locking device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .572.6 Top track - and panel fixation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .622.7 Checking the door gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .623. Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .633.1 4 Panels Asymmetric Mechanism Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .633.2 4 Panels Symmetric Mechanism Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .643.3 2 Panels Central Opening Mechanism Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .653.4 2 Panels Side Opening Mechanism Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .663.5 Components for 4 Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .673.6 Door fixation for 4 Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Warnings on how to keep the doors in good operating conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76Pag. Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag.Pag.Pag.Pag.Pag.Pag. Pag. Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag.Pag.The points that are important under the safety viewpoint and danger warnings are indicated with these symbols:Danger generalImportant warningsRisk of personal injury (e.g. sharp edges, protruding parts)Risk of damage to mechanical parts ( e.g. incorrect installation)Live partsINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20153.164Congratulations on choosing a WITTUR product!Before starting the installation of this product, read the information contained in this document.Before installation work begins, it is in your own interests to clarify what structural and spatial conditions are availablefor installation work, so that you can see which installation procedures should/must be carried out. Therefore it is recom-mended that all circumstances be taken into consideration, and to mentally plan the installation sequence before any rashor badly planned work is carried out. Check the goods or parts for correct and full delivery upon receipt.You will find important warnings on how to assemble and maintain your WITTUR product in good operating conditionsand to get the maximum of your investment.You will also find important information concerning the product care and maintenance which are an important factor toensure safety at all times.WITTUR has long been involved in research aimed at reducing noise level and in design that takes into due considerationthe product quality and the conservation of environment.This document is an integral part of the supply and must be available in the lift power room at all times.All products are provided with identification type label and in case with certification marks in accordance with the cur-rent rules.In case of need concerning the product, the identification data on the label must be always communicated to us.We hope you will get full satisfaction from this WITTUR product. Yours faithfully.WITTURFOREWORD AND WARNINGSWARNINGS- WITTUR will not be held liable for any damage caused by tampering of the packing material by thirds.- Before starting assembly, check that the product received corresponds to the order and to the packing list and that nodamage has occurred in transit.- Within its policy of continual research, WITTUR reserves to make changes to its products without notice. The figures,descriptions and data contained in this manual are intended as purely indicative and not binding.- To ensure the safety of the product, avoid any alteration or tampering.- WITTUR liability will be limited to the original components only.- WITTUR product is intended for use in the lift sector only, therefore WITTURliability shall be limited to such use.- This product is intended for professional use. Any improper use, including for hobby or DIY, is prohibited.- In order to prevent any injury to persons and damage to property, the handling, installation, adjustment and mainte-nance must be carried out by suitably trained personnel, using appropriate clothing and equipment.- Any masonry work connected with the correct installation of the product must be executed in a workmanlike manneraccording to the applicable laws.- The connection of the electric/electronic units to the local power supply must be executed in a workmanlike manneraccording to the applicable laws.- All metal parts supporting the electric/electronic units must be connected to an earth system in a workmanlike man-ner according to the applicable laws.- Before connecting the product to the power supply check that the products requirement corresponds with the powersupply available.- Before starting any work on the electric/electronic components disconnect power from the system.- WITTUR shall have no responsibility on the execution of masonry works or the connection of electric/electronic com-ponents to the power supply.-WITTUR shall not be liable for damages/injury to property/persons caused by improper use of the emergency openingdevices.INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20154.164SUGGESTIONS- Keep the material in the original packing, protected from bad weather and direct exposure to sun during the storageperiod in order to avoid the accumulation of water/condensation inside the packing material.- Never dispose of packing material in the environment.- Once dismantled, the product should be conveniently disposed as provided for by the local laws; neverdispose of inthe environment.- Whenever possible, re-cycling is preferable to disposal in dump sites.- Before re-cycling check the nature of the various materials and re-cycle in the appropriate way.INSTALLATION TOOLSFollowing tools are needed: hexagon keys 3mm, 5mm and 6mm Screw drivers (flat and crossheaded) Ratchet + extension; sockets 10mm and 13mm box spanner 17mm circlip plierThe landing toptrack is preadjusted at the factory. No other mechanical adjustments other mentioned in this instruction are required at site!DELIVERY toptrack panels sill closing weight emergency opening device fixingsOnly to be stored in the original package (plastic wrap). The components must not be unpackeduntil the installation begins.SuggestionsINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20155.1641. INSTALLATION1.1 GENERAL DESCRIPTION: TY 4AS, TY 4SFineline Landing Door AsymmetricFineline Landing Door SymmetricTy 4ASTy 4SINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20156.164Fineline Landing DoorFineline Landing Door1.2 GENERAL DESCRIPTION: TY 01/C, TY 11/R-LTy 01/CTy 11/R-LINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20157.164COCO/2COCOCO/2FLL symmetricFLL asymmetric - left openingFLL asymmetric - right openingcar doorlanding doorcar doorlanding doorcar doorlanding doorCO/21.3 LANDING DOOR ALIGNMENT WITH CAR DOOREach landing door has a mark in the top track area which is representing the center of the clear opening. While for the symmetric door the hexagon srew indicates the doors clear opening line, for asymmetric doors a hole with a diam-eter of 3mm indicates the center of the clear opening line. Ty 4STy 4ASLTy 4ASRINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20158.164COCO/2COCO/2Each car door has a mark in the operator area which is representing the center of the clear opening.While for the central opening and side opening door the hexagon srew indicates the doors clear opening line.FLLFLL - left side openingFLL - right side openingCOCO/2COCO/2Ty 01/CTy 11/RTy 11/Lcar doorlanding doorcar doorlanding doorcar doorlanding doorCOCO/2COCO/2INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.20159.1641.4 IDENTIFICATIONmanufacturer /date of manufacturingcertification numberType test designationand CE-labeltypeFINELINE Landing Top Trackclear opening (CO)serial number(defined by WITTUR)clear height (CH)opening directionlift numberINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201510.1641.5 POSITIONING OF THE LANDING DOOR5mmsill45mm5mmsill45mmwith door frame cover without door frame coverTy 4S Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201511.1645mm30mm545SillSillsillsillTy 01/C Ty 11/R-LINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201512.164ADJUSTMENT OF THE LANDING DOOR IN THE SHAFT:E121 2Fathom of the reference line in the shaft according image.reference linereference lineAdjustment of the Top Tracks to the reference line.SSSSmaxSmaxINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201513.1641.6 ASSEMBLY OF THE SILLToensureacorrectinstallationthefixingelements(dowel,strikearmature,...)mustbeusedaccordingtothewallcon-struction and the future forces.1CO R600600 6507007507008008508009006570RCOR/2R/2==2a2bwith additional bracketsINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201514.164asymmetric doorsymmetric door13034a4bTy 4STy 01/CTy 11/R-LTy 4ASTy 4ASTy 4STy 01/CTy 11/R-LINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201515.1641.7 ASSEMBLY OF THE FRAME152 36Alternative position4INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201516.1647Fixing can be adjusted by handaccording the shaft wall8910INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201517.1641.8 ASSEMBLYOFTHEMECHANISMCOVERCO +160Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201518.1641.9 ASSEMBLY OF THE TOP TRACK1.9.1 Standard installation on new jambs11) Secure the two M6 screws without tightening.Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201519.164322) Fasten the mechanism.3) Secure the mechanism using 4 M8 screws (A).4) Remove the M6 screws (B).sillvertical adjustmenthorizontal adjustmentRemove afterinstalling mechanismRemove afterinstalling mechanismAABAABTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201520.1641.9.2 Standard fixing on swing door only for Ty 4A (Asymmetric)LHToensureacorrectinstallationthefixingelements(dowel,strikearmature,...)mustbeusedaccordingtothewallcon-struction and the future forces.sillvertical adjustment21horizontal adjustment3045964,20PL+2-0LH+130Ty 4ASTy 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201521.1641.9.3 Fixing on swing door (alternative 1)2horizontal adjustmentToensureacorrectinstallationthefixingelements(dowel,strikearmature,...)mustbeusedaccordingtothewallcon-struction and the future forces.sill1vertical adjustment30120330CO45(12)CHCH+124,20+2-0CH+130Ty 4ASTy 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201522.1641.9.4 Fixing on swing door (alternative 2)Toensureacorrectinstallationthefixingelements(dowel,strikearmature,...)mustbeusedaccordingtothewallcon-struction and the future forces.sillhorizontal adjustmentvertical adjustment21CHCH+551312033013CO(55)+2-0CH+130Ty 4ASTy 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201523.1641.9.5 Wall fixing1a asymmetric door9012055CH+280MR-60 CO120Ty 4ASCO MR600244 650700750 279800 283850 313900 32570INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201524.1641a symmetric door9012012555CH+2280125M-120120Ty 4ASCO M6001070 650700750 1145800 1200850 1275900 1350INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201525.1649012012555CH+2280125M-1201201a central opening doorCO M6001070 650700750 1145800 1200850 1275900 1350Ty 01/CINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201526.1649012012555CH+2280125M-120120CO M6001070 650700750 1145800 1200850 1275900 1350Ty 11/R-L1a side opening doorINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201527.164sillhorizontal adjustmentvertical adjustmentToensureacorrectinstallationthefixingelements(dowel,strike armature,...) must be used according to the wall construc-tion and the future forces.2a+2-0CH+130Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201528.1642b - Assembling of the top track with the installation templateCH+90Ty 4S Ty 01/C Ty 11/R-L Ty 4ASCH=1900CH=2000CH=1950CH=2050CH=2100INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201529.164INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201530.1641.10 ASSEMBLY OF DOOR PANEL1.10.1 Panel shoes assemblyTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201531.164Slow panel1) Open the mechanism2) Insert the panel into the sill3) Close the mechanism4) Secure the panel on the mechanism, see 1.10.3.1.10.2 Inserting door panelsTy 4S Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201532.1641) Close the mechanism2) Insert the panel into the sill3) Open the mechanism4) Secure the panel on the mechanism, see 1.10.4.Fast panelTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201533.1641.10.3 Assembly of the rear door panels1.10.4 Assembly of the front door panels12312)...25Nm3)...see 1.10.41231...see 5.3Schnorr-washer For better assembling open the door 5cm.2mm...slots ...slots1.10.5 Adjustment of the panel gapTy 4S Ty 01/C Ty 11/R-L Ty 4ASTy 4STy 01/CTy 11/R-LTy 4ASTy 4STy 01/CTy 11/R-LTy 4AS2)...25Nm3)...see 1.10.4INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201534.1641.10.6 Adjustment of the narrow door panels (asymmetric door)1) Relax counter roller2) Relax hexagon screw3) Adjust the door panel4) Fix the hexagon screw5) Adjust the counter roller (for all counter roller available; thighten the counter roller with the hexagon screw so, that it is stillbarely rotatable)4231335Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201535.1641.11 ASSEMBLY OF THE EMERGENCY OPENING DEVICE112342a Ty 4AS 2b Ty 01/C; 11/R-L; 4STy 4STy 01/CTy 11/R-LTy 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201536.164311.12 EMERGENCYOPENINGCONTACT(OPTIONAL)Contactpositionadjustable20...0,5Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201537.1641.13 ASSEMBLY OF THE CLOSING WEIGHT ROPE1.13.1 Replacement of the closing weight roperemove screw213 4 5Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201538.1641.13.2 Adjustment of the closing weight roperelax screw==tight screw1234Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201539.1641.14 TOE GUARD ASSEMBLINGTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201540.1641.15 PLACINGTHEMECHANISMSONTHETHRESHOLDSsill gap 25 mm+3-0distance - running rails 25 mm+3-0Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201541.1641.16 ASSEMBLY OF THE PANEL BUFFERSThe contact surface on the door panels must becarefully cleaned. ~60~85Ty 4S Ty 01/C Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201542.164The contact surface on the door panels must becarefully cleaned. Ty 11/R-L1.16.1 Assembly of the panel buffers~ 60Fast PanelsClosing Side FrameINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201543.1641.17 ASSEMBLY OF THE LINTEL1.17.1 Asymmetric Landing door Lintel1.17.2 Symmetric Landing door LintelL2 L3M410CO L2 L3600 125 250650 133 275700 142 300750 138 325800 146 350850 138 375880 141 390900 144 400L3 = =M410CO L3600 250650 275700 300750 325800 350850 375880 390900 400Ty 4STy 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201544.1641.17.3 Side opening Landing door LintelTy 11/R-LCO L2 L3600 125 250650 133 275700 142 300750 138 325800 146 350850 138 375880 141 390900 144 400INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201545.1641.18 DOOR CONTACT CABLEsafety circuitgroundTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201546.1641.19 INSTRUCTION ON HOW TO KEEP THE DOORS IN GOOD OPERATING CONDITIONSTo prevent failure or malfunction and keep the system efficient, it is necessary toregularly check for technical degrada-tion and ensure that the conditions required by current regulations are maintained.After ending the door assembly the running surfaces of the running rails and the guiding - and counter roller has to becleaned.Degradation can depend on a variety of factors, such as:- Work intensity- Age of product- Volume of panels- Weather and environmental conditions (xx)- Cleanliness of the room- Correct maintenance- Etc.And may involve:- Play/interference between the panels and between panels and jambs in accordance with current regulations- Play in coupling device- State/condition of fixing and coupling elements- Condition of parts subject to wear- Efficiency of lock and associated contacts- Anything else that may be affected by the type of application.For these reasons, the schedule for part replacement cannot be set beforehand.INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201547.1641.20 TESTING THE FUNCTIONS1.20.1 Landing door locknslock hookdoor contactsCheck of the closing function:- The lock hook must touch buffer in closing position- Lock hook and beak overlap when lock is fully closed must be ~2mm.- The function of the door contacts must be available. (infeed contact min. 3mm)end-buffer~23~2123Ty 4S Ty 01/C Ty 11/R-L Ty 4ASTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201548.1641.20.2 Door gapCheck the gap between the door panels, between frame and door panel and the gap to the lintel. 5mm5mm 5mm5mm5mm2mmlintelTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201549.1641.20.3 Emergency closingThe door must close itself automaticly from each position.closing weightTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201550.164Door lock contactEmergency opening contact1.20.4 Emergency opening contactEmergency opening contact must be opened before the door get unlocked by the landing lock.Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201551.1642. MAINTENANCE2.1 REPLACEMENTOFTHESLIDINGSHOESCheck failures, break or abrasion1 2Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201552.1642.2 REPLACEMENT OF THE ROLLER1Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201553.164fast hangerplate2 34 56INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201554.164Ty 4S Ty 11/R-L Ty 4ASTy 4S Ty 11/R-L Ty 4AS1323214Adjust the rope endings in the rope actuator (3) so thatwhenthedoorisopentheendoftheropeisbendingdown and it doesnt contact the rope pulley. Then fix the rope endings with the headless pin (4) andmount the rope actuator.2.3 REPLACEMENT OF THE SYNCHRONISATION ROPE2.3.1 Removing the synchronisation ropeRelax the rope pulley (1) and the rope fixing (2), then remove the rope actuator (3).To remove the rope it is necessary to relax the headless pin in the rope actuator.2.3.2 Synchronisation rope assemblyMount the synchonization rope on the rope pulleys (1) and arrange it through the rope fixing (2).INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201555.164Ty 4S Ty 11/R-L Ty 4ASTy 4S Ty 11/R-L Ty 4AS122.3.3 Clamping the synchronisation ropeClamp the inner rope pulley with the screw driver (1) and fix the hexagon screw (2).3122.3.4 Synchronizing the doorOpen the door as far as the outer edge of the hanger plate has a distance to the mechanismus of 12mm. Then fix the rope fix-ing (3).INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201556.1642.4 REPLACEMENTOFTHEWINDOWGLASSESTy 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201557.1642.5 CHECKING THE LOCKING DEVICE2.5.1 Lock hooke locking deviceChek of the circlips2.5.2 Synchronisation ropeVisual inspection of the synchronisation rope (1), the synchronisation roller (2) and the rope fixing bracket (3).1223Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201558.1642.5.3 Emergency driveright sideleft sideMeasurement of the overlap of the emergency hook.11mm5mmTy 4S Ty 4ASTy 4S Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201559.1642.5.4 Hanger plate guidingVisual inspection of the roller on following characteristics:break, crack, abrasion, failure and correct insatallation.Deposits and dirt on the running rail and rollers must be removed.Emergencyguidingleftside:hexagonscrew(1)andlift-outguard (2)Emergency guiding right side: bushing (3) and lift-out guard (4)1 13 342Visuel inspection of the Emergency guiding on following characteristics:break, failure and correct installation.Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201560.1642.5.5 Closing weight ropeVisuel inspection of the closing weight rope on following characteristics:break, abrasion and correct installationFunction test of the emergency closing see paragraph 1.20.3.Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201561.1642.5.6 Emergency opening deviceVisuel inspection of the closing weight rope on following characteristics:completeness and correct installation.Check the free movement with the emergency opening device key.2.5.7 Testing the landing door locksee paragraph 1.20.Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201562.1642.6 TOP TRACK - AND PANEL FIXATIONVisuel inspection of the fixation on following characteristics:break, failure and correct installation2.7 CHECKING THE DOOR GAPsee paragraph 1.20.2.Ty 4S Ty 01/C Ty 11/R-L Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201563.1643. SPARE PARTS3.1 4 PANELS ASYMMETRIC MECHANISM DOOR1512346789101213Pos. Part number Description Remarks1902790 G01902790 G02Landing door lock completeleft opening doorright opening door2 902794 G01 Landing roller-set 3xlanding roller, 3xcirclip3 274093 Door contact 1 piece4 274094 Door contact bridge 1 piece5 900329 G01 Door contact cable not figure6902960 G01902960 G02Slow hanger plate, small side completeleft opening door, CO...must be specifiedright opening door, CO...must be specified7902958 G01902958 G02Slow hanger plate, small side completeleft opening door, CO...must be specifiedright opening door, CO...must be specified8902952 G11902952 G12Fast hanger plate, small side completeleft opening doorright opening door9902964 G01902964 G02Fast hanger plate, small side completeleft opening door, CO...must be specifiedright opening door, CO...must be specified10 89739 H02 Synchronisation rope L=100011 902899 G01 Hanger plate roller-set4xroller, 2xcirclip, 1xexcenter bushing, 2xscrew,2xSchnorr washer12 902915 G01 Synchronisation rope actuator13 902915 G02 Synchronisation rope fixing14 602767 G02 Synchronisation rope pulley complete incl. fixing elements15902902 G01902902 G02Top Track completeleft opening door, CO...must be specifiedright opening door, CO...must be specified14Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201564.164Pos. Part number Description Remarks1 902790 G01 Landing door lock complete2 902794 G01 Landing roller-set 3xlanding roller, 3xcirclip3 274093 Door contact 1 piece4 274094 Door contact bridge 1 piece5 900329 G01 Door contact cable not mapped6 902896 G02 Slow hanger plate, right side complete CO...must be specified7 902896 G01 Slow hanger plate, left side complete CO...must be specified8 902994 G04 Fast hanger plate, right side complete CO...must be specified9 902994 G03 Fast hanger plate, left side complete CO...must be specified10 89739 H02 Synchronisation rope L=100011 902899 G01 Hanger plate roller-set4xroller, 2xcirclip, 1xexcenter bushing, 2xscrew,2xSchnorr washer12 902915 G01 Synchronisation rope actuator13 902915 G02 Synchronisation rope fixing14 602767 G02 Synchronisation rope pulley complete incl. fixing elements15 902903 G01 Top Track complete CO...must be specified12346789101213143.2 4 PANELS SYMMETRIC MECHANISM DOOR15Ty 4SINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201565.1643.3 2 PANELS CENTRAL OPENING MECHANISM DOORPos. Part number Description Remarks1 1008063A01 Landing door lock complete2 0902794 G01 Landing roller-set 3xlanding roller, 3xcirclip3 W002105 Door contact 1 piece4 W002170 Door contact bridge 1 piece5 1008063 Door contact cable not mapped61006577 AOT RIGHTSlow hanger plate, right side complete CO...must be specified71006577 AOL LEFTSlow hanger plate, left side complete CO...must be specified8 902899 G01 Hanger plate roller-set4xroller, 2xcirclip, 1xexcenter bushing, 2xscrew,2xSchnorr washer9 1006902 Top Track complete CO...must be specified39Ty 01/C67412INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201566.1643.4 2 PANELS SIDE OPENING MECHANISM DOORTy 11/R-L367412128 1110Pos. Part number Description Remarks1 1006794 Landing door lock complete2 0902794 G01 Landing roller-set 3xlanding roller, 3xcirclip3 W002105 Door contact 1 piece4 W002170 Door contact bridge 1 piece5 1006794 Door contact cable not mapped6 1006906 Slow hanger plate, complete CO...must be specified7 1008320 Fast hanger plate, complete CO...must be specified8 1008299 Synchronisation rope L=10009 902899 G01 Hanger plate roller-set4xroller, 2xcirclip, 1xexcenter bushing, 2xscrew,2xSchnorr washer10 902915 G01 Synchronisation rope actuator11 902915 G02 Synchronisation rope fixing12 602767 G02 Synchronisation rope pulley complete incl. fixing elements13 1006912 Top Track complete CO...must be specifiedINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201567.1643.5 COMPONENTSFOR4PANELS35678101113118201915491216172Ty 4S Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201568.164Pos. Part number Description Remarks1 3212.39.5000 Sliding shoe set 8 pieces kit2 3212.23.0501 Frame assembly kit Top brackets + frame assembly screws3 3212.39.5009 Fixing kit for small panels4 3212.05.5506 Infillplate CO, surface finish... must be specified5 3212.05.7500 Silldoor type, opening handCO...must be specified6 3212.05.5508 Toe guard73212.04.05203212.04.05223212.04.0527Closing weightasymmetric doorsymmetric door standard, CO...must be specifiedsymmetric door with panel window, CO...must bespecified8 3212.04.0521Closing rope for counterweight, including ropesecuring clamp9 3212.05.9502 Counterweight guide felt 1m10 601115 G01 Roller for closing weight rope11902985 G01902985 G02Emergency opening device completeasymmetric doorsymmetric door123212.05.9500 + 3212.05.6501Bushing and spring for EOD13 C1280 Emergency opening key14 3212.32.0230 Installation gauge not mapped15902748 G01902748 G02902748 G03902748 G04902748 G05902748 G06Emergency opening contactEmergency opening contact with 230V remote resetEmergency opening contact with 24V remote resetasymmetric left opening door or symmetric doorasymmetric right opening doorasymmetric left opening door or symmetric doorasymmetric right opening doorasymmetric left opening door or symmetric doorasymmetric right opening door163212.05.5546 +3212.39.5010Cover plate with fixing elements CO, door type...must be specified17 3212.23.0500 Sill fixing kit Brackets + sill fixing screws18 3212.03.0500 Landing door frame CO, CH, surface finish...must be specified for 1 panel19 C1263 Panel buffer 1 piece203212.05.55103212.23.0508Side bracket kit with anchorsFrame width must be specifiedKit for 2 brackets:2 pc. 3212.05.5510 +1 pc. 3212.23.0508Ty 4S Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201569.1643.4.1 Componentsfor2Panels Central Opening345679101211719181481115162Ty 01/CINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201570.164Pos. Part number Description Remarks1 1006949 Sliding shoe set 4 pieces kit2 1007159 Frame assembly kit Top brackets + frame assembly screws3 1010397 Fixing kit for small panels4 1006928 Silldoor type, opening handCO...must be specified5 1006951 Toe guard6 1010483 Closing weight7 0902992Closing rope for counterweight, including ropesecuring clamp8 1010482 Counterweight guide felt 1m9 1000051 Roller for closing weight rope10 0902985A03 Emergency opening device completeasymmetric doorsymmetric door110673109 +0902986Bushing and spring for EOD12 C1280 Emergency opening key13 GM.2.001049 Installation gauge not mapped14902748 G01902748 G03902748 G05Emergency opening contactEmergency opening contact with 230V remote resetEmergency opening contact with 24V remote resetsymmetric doorsymmetric doorsymmetric door153212.05.5546 +3212.39.5010Cover plate with fixing elements CO, door type...must be specified16 1007156A01 Sill fixing kit Brackets + sill fixing screws17 1006937 Landing door frame CO, CH, surface finish...must be specified for 1 panel18 C1263 Panel buffer 1 piece1910071611007203Side bracket kit with anchorsFrame width must be specifiedKit for 2 brackets:8 pc. 1007161 +1 pc. 1007203Ty 01/CINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201571.1643.4.1 Componentsfor2Panels Side OpeningTy 11/R-L35678101113118201915491216172INSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201572.164Pos. Part number Description Remarks1 1006949 Sliding shoe set 8 pieces kit2 1007159 Frame assembly kit Top brackets + frame assembly screws3 1010397 Fixing kit for small panels4 1007069 Infillplate CO, surface finish... must be specified5 1007094 Silldoor type, opening handCO...must be specified6 1006951 Toe guard7 1010483 Closing weight8 0902992Closing rope for counterweight, including ropesecuring clamp9 1010482 Counterweight guide felt 1m10 1000051 Roller for closing weight rope11 0902985 Emergency opening device complete symmetric door120673109 +0902986Bushing and spring for EOD13 C1280 Emergency opening key14 GM.2.001049 Installation gauge not mapped15902748 G01902748 G02902748 G03902748 G04902748 G05902748 G06Emergency opening contactEmergency opening contact with 230V remote resetEmergency opening contact with 24V remote resetleft opening doorright opening doorleft opening doorright opening doorleft opening doorright opening door163212.05.5546 +3212.39.5010Cover plate with fixing elements CO, door type...must be specified17 1007165A02 Sill fixing kit Brackets + sill fixing screws18 107091 Landing door frame CO, CH, surface finish...must be specified for 1 panel19 C1263 Panel buffer 1 piece201007161 +1007162Side bracket kit with anchorsFrame width must be specifiedKit for 2 brackets:8 pc. 1007161 +1 pc. 1007162Ty 11/R-LINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201573.164Pos. Part number Description Remarks1 3212.39.5003 Bracket set for swing door standard (no figure) Standard fixing on swing door2 3212.39.5005 Bracket set for swing door alternative 1 (no figure) Alternative fixing 1 on swing door3 3212.39.5007 Bracket set for swing door alternative 2 (no figure) Alternative fixing 2 on swing door4 3212.39.5001 Bracket set for shaft wall Wall fixing43.6 DOOR FIXATION FOR 4 PANELSTy 4S Ty 4ASINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201574.164Ty 01/CPos. Part number Description Remarks1 3212.39.5003 Bracket set for swing door standard (no figure) Standard fixing on swing door2 3212.39.5005 Bracket set for swing door alternative 1 (no figure) Alternative fixing 1 on swing door3 3212.39.5007 Bracket set for swing door alternative 2 (no figure) Alternative fixing 2 on swing door4 3212.39.5001 Bracket set for shaft wall Wall fixing43.5.1 Doorfixationfor2PanelsCenterOpeningINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201575.164Ty 11/R-LPos. Part number Description Remarks1 3212.39.5003 Bracket set for swing door standard (no figure) Standard fixing on swing door2 3212.39.5005 Bracket set for swing door alternative 1 (no figure) Alternative fixing 1 on swing door3 3212.39.5007 Bracket set for swing door alternative 2 (no figure) Alternative fixing 2 on swing door4 3212.39.5001 Bracket set for shaft wall Wall fixing43.5.1 Door fixation for 2 Panels Side OpeningINSTRUCTION HANDBOOK LANDING DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201576.164WARNINGS ON HOW TO KEEP THE DOORS IN GOOD OPERATING CONDITIONSIn order to prevent failures or incorrect operation and to maintain the system in good conditions, the technical efficien-cy of the system should periodically be checked, to ensure compliance with the applicable laws.The technical efficiency depends on various factors such as:- Work load- Years of operation - Door weight- Climatic and environmental conditions- Cleanness of environment- Correct maintenance- Etc.And it can affect:- Clearance/interference between the doors, and between the doors and posts according to the applicable laws- Clearance of coupling device- Status/conditions of fixing and coupling elements- Conditions of parts affected by wear- Efficiency of the lock and relevant contacts- Any other parts that may be affected by the type of application.For these reasons it is not possible to establish a general part replacement programme beforehand.All screws used for the assembly of our product are screwed by means of a tightening torque as shown on following table:Screw Max torque (Nm) Min torque (Nm)M3 1,1 0,9M4 2,6 2,1M5 5,1 4,1M6 9 7M8 21 17M10 42 34M12 71,4 57,1In case of need please refer to above table.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201577.164CAR DOORINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201578.164INDEXSymbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79Warnings and Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .801. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .811.1 General description: Ty 4AS, Ty 4S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .811.2 General description: Ty 02/C, Ty 12/R-L. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .821.3 Car door alignment with landing door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .831.4 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .851.5 Assembly of the sill. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .861.6 Assembly of the operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .881.7 Door panels assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .911.8 Toe guard assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .961.9 Placing the mechanisms on the thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .971.10 Assembly of the panel buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .981.11 Assembly of the infillplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1001.12 Assembly of the light sensor system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1021.13 Assembly of the panel- and sill extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1051.14 Coupler with Car Door Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1061.15 Emergency opening device for coupler with Car Door Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1071.16 Instruction on how to keep the doors in good operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1081.17 Testing the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1091.18 Adjustment of the open-end position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1102. General information prior to installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1122.1 Description and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1123. Electronic assembly layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1123.1 Insulation test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1124. Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1134.1 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1134.2 Safety Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1165. Exchange of electronic box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1165.1 Preparation and learning of door parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1165.2 Driving the doors with the elevator controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1185.3 Driving the doors by the service drive buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1185.4 Reset of coupler width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1185.5 Reset of all door parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1185.6 Connection of DC motor (e.g: replacement of old electronic). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1186. Adjustments always to be done . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1196.1 Closing Force Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1196.2 Adjustment of the speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1206.3 Setting speed according to Disabled People Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1207. Description of LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1217.1 LEDs Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1217.2 LEDs Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1217.3 Different LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1218. Electrical Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1228.1 Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1228.2 Passenger protection device input and supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1238.3 Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1239. DIP-SWITCHES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12410. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12510.1 The door does not move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12510.2 The door does not reopen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12510.3 Faults causing reset or switch off (STATE LED is blinking, blinkcode (x)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12610.4 Faults decreasing performance of door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12611. Eco+ wiring diagram Drive (P.S. motor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12711.1 With WSE PLUS Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12711.2 With W2D Photocell. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12812. Wittur Programming Tool Interface Software description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12912.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12912.2 Connecting the Wittur Programming Tool to the ECO+ - electronic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12912.3 Menu structure of Programming Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12912.4 Door adjustment with the Programming Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130Pag. Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag. Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag. Pag.Pag.Pag.Pag. Pag.Pag.Pag. Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201579.16413. Default adjustment of ECO+ software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13614. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13714.1 Operator-and Panel fixation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13714.2 Checking the door gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13714.3 Synchronisation rope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13814.4 Emergency drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13914.5 Hanger plate guiding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14014.6 Assembly of the spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14114.7 Replacement of the synchronisation rope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14714.8 Replacement of the window glasses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14815. Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14915.1 4 Panels asymmetric railing complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14915.2 4 Panels asymmetric operator complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15015.3 4 Panels symmetric railing complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15115.4 4 Panels symmetric operator complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15215.5 2 Panels central opening symmetric railing complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15315.6 2 Panels central opening symmetric operator complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15415.7 2 Panels side opening railing complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15515.8 2 Panels side opening operator complete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15615.9 Components for 4 panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15715.10 Components for 2 panels center opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15915.11 Components for 2 panels side opening. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161Warnings on how to keep the doors in good operating conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163INSTRUCTION HANDBOOK CAR DOORCongratulations on choosing a WITTUR product!Before starting the installation of this product, read the information contained in this document.Before installation work begins, it is in your own interests to clarify what structural and spatial conditions are availablefor installation work, so that you can see which installation procedures should/must be carried out. Therefore it is recom-mended that all circumstances be taken into consideration, and to mentally plan the installation sequence before any rashor badly planned work is carried out. Check the goods or parts for correct and full delivery upon receipt.You will find important warnings on how to assemble and maintain yourWITTUR product in good operating conditionsand to get the maximum of your investment.You will also find important information concerning the product care and maintenance which are an important factor toensure safety at all times.WITTUR has long been involved in research aimed at reducing noise level and in design that takes into due considerationthe product quality and the conservation of environment.This document is an integral part of the supply and must be available in the lift power room at all times.All products are provided with identification type label and in case with certification marks in accordance with the current rules.In case of need concerning the product, the identification data on the label must be always communicated to us.We hope you will get full satisfaction from this WITTUR product. Yours faithfully.WITTURFOREWORDSYMBOLS USEDThe points that are important under the safety viewpoint and danger warnings are indicated with these symbols:Danger generalImportant warningsRisk of personal injury (e.g. sharp edges, protruding parts)Risk of damage to mechanical parts (e.g. incorrect installation)Live partsPag. Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag.Pag. Pag.Pag.Pag.Pag. Pag.Pag.Pag. Pag.Pag.Pag.Pag.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201580.164DELIVERY Car door operator panels sill coupler (optional) swing door unlocking (optional) fixingsOnly to be stored in the original package (plastic wrap). The components must not be unpackeduntil the installation begins.INSTALLATION TOOLSFollowing tools are needed: hexagon keys 3mm, 5mm and 6mm Screw drivers (flat and crossheaded) Ratchet + extension; sockets 10mm and 13mm box spanner 17mm circlip plierThe landing toptrack is preadjusted at the factory. No other mechanical adjustments other mentioned in this instruction are required at site!SUGGESTIONS- Keep the material in the original packing, protected from bad weather and direct exposure to sun during the storage periodin order to avoid the accumulation of water/condensation inside the packing material.- Never dispose of packing material in the environment.- Once dismantled, the product should be conveniently disposed as provided for by the local laws; never dispose of in the envi-ronment.- Whenever possible, re-cycling is preferable to disposal in dump sites.- Before re-cycling check the nature of the various materials and re-cycle in the appropriate way.WARNINGS AND SuggestionsWARNINGS- WITTUR will not be held liable for any damage caused by tampering of the packing material by thirds.- Before starting assembly, check that the product received corresponds to the order and to the packing list and that no dam-age has occurred in transit.- Within its policy of continual research, WITTUR reserves to make changes to its products without notice. The figures, descrip-tions and data contained in this manual are intended as purely indicative and not binding.- To ensure the safety of the product, avoid any alteration or tampering.- WITTUR liability will be limited to the original components only.- WITTUR product is intended for use in the lift sector only, therefore WITTUR liability shall be limited to such use.- This product is intended for professional use. Any improper use, including for hobby or DIY, is prohibited.- Inordertopreventanyinjurytopersonsanddamagetoproperty,thehandling,installation,adjustmentandmaintenancemust be carried out by suitably trained personnel, using appropriate clothing and equipment.- Any masonry work connected with the correct installation of the product must be executed in a workmanlike manner accord-ing to the applicable laws.- The connection of the electric/electronic units to the local power supply must be executed in a workmanlike manner accord-ing to the applicable laws.- Allmetalpartssupportingtheelectric/electronicunitsmustbeconnectedtoanearthsysteminaworkmanlikemanneraccording to the applicable laws.- Before connecting the product to the power supply check that the products requirement corresponds with the power supplyavailable.- Before starting any work on the electric/electronic components disconnect power from the system.- WITTUR shall have no responsibility on the execution of masonry works or the connection of electric/electronic componentsto the power supply.-WITTUR shall not be liable for damages/injury to property/persons caused by improper use of the emergency opening devices.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201581.1641. INSTALLATION1.1 GENERAL DESCRIPTION: TY 4AS, TY 4SFineline Car Door AsymmetricFineline Car Door SymmetricTy 4ASTy 4SINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201582.164Fineline Car DoorFineline Car Door1.2 GENERAL DESCRIPTION: TY 02/C, TY 12/R-LTy 02/CTy 12/R-LINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201583.1641.3 CAR DOOR ALIGNMENT WITH LANDING DOOREach car door has a mark in the operator area which is representing the center of the clear opening. While for the symmetric door the hexagon srew indicates the doors clear opening line, for asymmetric doors a hole with a diam-eter of 3mm indicates the center of the clear opening line. COCOFLC symmetricFLC asymmetric - left openingFLC asymmetric - right openingCO/2CO/2CCCLLLCOCO/2Ty 4STy 4ALTy 4ARINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201584.164CO/2COCO/2COCOCO/2CO/2COCO/2COCOCO/2CO/2COCO/2COCOCO/2Each car door has a mark in the operator area which is representing the center of the clear opening.While for the central opening and side opening door the hexagon srew indicates the doors clear opening line.FLC central openingFLC left side openingFLC right side openingCO/2COCO/2COCOCO/2CO/2COCO/2COCOCO/2CCCLLLCO/2COCO/2COCOCO/2Ty 02/CTy 12/RTy 12/LINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201585.1641.4 IDENTIFICATIONCE-labeltypeFINELINE Car Door Operatorclear opening (CO)serial number(defined by WITTUR)clear height (CH)opening directionlift numbermanufacturer /date of manufacturingelectronic-short descriptionINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201586.1641.5 ASSEMBLY OF THE SILLToensureacorrectinstallationthefixingelements(dowel,strikearmature,...)mustbeusedaccordingtothewallcon-struction and the future forces.126565CO R600600 650700750700800850800900R/2R/2RCO==INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201587.16434a4basymmetric doorsymmetric door130Ty 4STy 02/CTy 12/R-LTy 4ASTy 4ASTy 4STy 02/CTy 12/R-LINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201588.1641.6 ASSEMBLY OF THE OPERATOR12Ty 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201589.164horizontal adjustmentsillCH+130+2-0CH+7530CO3013243INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201590.164sill=455CH445100 66801614min 30INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201591.1641.7 DOOR PANELS ASSEMBLY1.7.1 Panel shoes assemblyTy 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201592.1641.7.2 Insert of the door panelsTy 4S Ty 12/R-L Ty 4ASSlow panelINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201593.164Ty 4S Ty 02/C Ty 12/R-L Ty 4ASFast panelINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201594.1641.7.3 Assembly of the rear door panels1.7.4 Assembly of the front door panels12311231222)...25Nm3)...see 1.7.4Ty 4S Ty 02/C Ty 12/R-L Ty 4ASTy 4S Ty 02/C Ty 12/R-L Ty 4AS2)...25Nm3)...see 1.7.4INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201595.1641.7.5 Adjustment of the narrow door panels (asymmetric door)1) Relax counter roller2) Relax hexagon screw3) Adjust the door panel4) Fix the hexagon screw5) Adjust the counter roller (for all counter roller available; thighten the counter roller with the hexagon screw so, that it is stillbarely rotatable)4231335Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201596.1641.8 TOE GUARD ASSEMBLINGTy 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201597.1641.9 PLACINGTHEMECHANISMSONTHETHRESHOLDSsill gap 25 mm+3-0distance - running rails 25 mm+3-0Ty 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201598.1641.10 ASSEMBLY OF THE PANEL BUFFERSThe contact surface on the door panels must becarefully cleaned. Ty 4S Ty 02/C Ty 12/R-L Ty 4AS~ 85~ 60INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.201599.164The contact surface on the door panels must becarefully cleaned. Ty 12/R-L1.10.1 Assembly of the panel buffers~ 60Fast PanelsClosing Side FrameINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015100.1641.11 ASSEMBLY OF THE INFILLPLATE1.11.1 Asymmetric Door1.11.2 Symmetric doorL2M410L3M4L3 =10=CO L3600 250650 275700 300750 325800 350850 375880 390900 400CO L2 L3600 125 250650 133 275700 142 300750 138 325800 146 350850 138 375880 141 390900 144 400Ty 4STy 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015101.164CO L3600 200650 225700 250750 275800 300850 325900 3501.11.3 Side opening landing door LintelTy 11/R-LM3L3 5017L2INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015102.1641.12 ASSEMBLY OF THE LIGHT SENSOR SYSTEM1.12.1 Preassembly12354The light sensor profile (1) must be fixed on the LSE fixing (3) with thread-rolling screws (2).Fix the cable with binders (4) on the LSE fixing. The gap to the lower LSE fixing (5) must be adjust the picture and the ham-mer screw (6) must be mounted easily.AA=10 (CH 2000)110 (CH 2100)6Ty 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015103.1641.12.2 Assembly on the operator132Fix the LSE bracket (1) with the screws (2).Accordinglymountthepre-assembledLSEfixing(3)onthe LSE bracket without fixing the screws completely.FIx the cable on the LSE bracket officinal the picture.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015104.1641.12.3 Assembly on the sillThe lower LSE fixing must be moved into the sill from the side so that the hammer screw can be mounted with the sill.645546Light sensorSill25Ty 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015105.1641.13 ASSEMBLY OF THE PANEL- AND SILLEXTENSIONTy 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015106.1641.14 COUPLER WITH CAR DOOR LOCKCar stops in door zone:The landing rollers are detected. They operate the lock vane and the latch opens. Car stops out of door zone:No landing rollers are detected. The lock vane is not touched and the latch keeps closed.CAR SILL LINELANDING SILL LINEOPENED VANESINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015107.1641.15 EMERGENCY OPENING DEVICE FOR COUPLER WITH CAR DOOR LOCKThe rope of the car door emergency opening device is fixed to the bottom end of the door panel. By pulling the rope, the car door lock is unlocked.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015108.1641.16 INSTRUCTION ON HOW TO KEEP THE DOORS IN GOOD OPERATING CONDITIONSTo prevent failure or malfunction and keep the system efficient, it is necessary toregularly check for technical degrada-tion and ensure that the conditions required by current regulations are maintained.After ending the door assembly the running surfaces of the running rails and the guiding - and counter roller has to becleaned.Degradation can depend on a variety of factors, such as:- Work intensity- Age of product- Volume of panels- Weather and environmental conditions (xx)- Cleanliness of the room- Correct maintenance- Etc.And may involve:- Play/interference between the panels and between panels and jambs in accordance with current regulations- Play in coupling device- State/condition of fixing and coupling elements - Condition of parts subject to wear- Efficiency of lock and associated contacts- Anything else that may be affected by the type of application.For these reasons, the schedule for part replacement cannot be set beforehand.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015109.1641.17 TESTING THE FUNCTIONS1.17.1 Door gapCheck the gap between the door panels, between frame and door panel and the gap to the lintel. 2mm5mm5mm5mm 5mmLintel5mmTy 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015110.164Ty 4S Ty 02/C Ty 12/R-L Ty 4AS1.18 ADJUSTMENT OF THE OPEN-END POSITIONAfter adjustment of the clear opening new learning process necessary (see 5.1).relax screwopen door12INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015111.1643tight screwWhen the door is completely open put the open end bracket aigainst the belt fixing and tight the srew.At clear opening 880 the open end bracketmust be fixed on the 2 right fixing holes.INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015112.1642.1 DESCRIPTION AND FUNCTIONECO+ door drives are used for low and mid duty elevators. The Drive can move panel masses up to 130kg complete door pack-age weight.3. ELECTRONIC ASSEMBLY LAYOUT2. GENERAL INFORMATION PRIOR TO INSTALLATIONPlug description:X1 - InputsX2 - OutputsX3 - Transformer secondary windingX4 - MotorX5 - Battery supplyX8 - RS485 interface for WPT (Wittur Programming Tool)X10 - Motor encoderX12 - Reference switchX15 - Photo Cell (Curtain of light) ReceiverX16 - Photo Cell (Curtain of light) TransmitterX40 - Test drive buttonsX60 - Extension plugCaution: Before carrying out tests on system's insulation, connector X5 must be disconnected.3.1 INSULATION TESTSTATE LEDLEARN BUTTONTy 4S Ty 02/C Ty 12/R-L Ty 4ASINSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015113.1644.1 POWER SUPPLY- The ECO+ - drive provides transformers for both different voltage ranges and can supply with 127VAC or 230VAC.- Select the recommended fuse for the nominal voltage range, see table 4. COMMISSIONING- Line in supply is connected to a plug with screw terminals (D1).4.1.1 Emergency supply- The battery's supply takes place through the X5 connector.Pay attention: the battery has to be connected only in case of absence of thesupply indicated on point 4.1.The ECO+ electronic can be used as replacement for old ECO electronics using DC Motor.Thedooroperatorssupplieddirectlyfromthefactoryarepre-adjusted:itisnotnecessarytocarryoutthedoorCO(ClearOpening) learning.The ECO+ drive at first installation or after switch-off /switch-on will use the first two complete closing / opening cycles tooptimize door CO: STATE LED off CO optimized.Nominal Supply Voltage Range:Automatic fuse slow (in control panel)127VAC2A230VAC1AMinimum cable required 1mm 0,75mmBattery voltageMin. cable sq. measure 24VDC-4Ah1,5mmD1PE = Connect ground wireN = Connect neutral wire120 = Connect 127 VAC phase wire230 = Connect 230 VAC phase wireRemove the plastic block before connecting the termi-nal 120INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015114.1644.1.2 Emergency procedure in automatic mode (specialized technical staff not present):If mains power is removed, to ensure correct operation of the emergency procedure in automatic mode via the control panel suppliedby the buffer battery, it is necessary to supply the ECO+ drive with power from a battery (24 Vdc 4 Ah) via connector X5: the batterypower must be supplied immediately after mains power is removed (the ECO+ drive must not be switched off ).The opening of doors for opening I1 (OPENING) will be managed by the control panel. Fig.1 shows the recommended wiring diagram.Door opening will be automatic (without the help of the lift controller), if relay K3 is used to activate input I1 (OPENING), or the liftcontroller will have to manage input I1 (OPENING) to activate door opening: Fig.1 recommended wiring diagram.NOTE:1. Input I1 is activated via contact K3 by a micro-switch installed inside the shaft. The micro-switch is activated by the arrival ofthe car to the floor where it was installed and the ECO+ card will control input I1 via contact K3, only when powered by abattery.2. If power is removed while the car is in line with the floor and the closing limit switch of the ECO+ card is not activated, it willbe possible to open the door manually at that floor, as the ECO+ card will leave the motor unpowered.Fig. 1INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015115.1644.1.3 Emergency procedure in manual mode (specialized technical staff present):1. If mains power is removed, to ensure correct operation of the emergency procedure in manual mode, we recommend supplyingthe ECO+ drive with battery power (24 Vdc 4 Ah ) via connector X5: the battery power must be supplied immediately after mainspower is removed (the ECO+ drive must not be switched off ). This way it will be possible to align the elevator cabin with the desiredfloor by means of a manual operation: the doors can only be opened manually: Fig.2 recommended wiring diagram.NOTE:If the operator is equipped with retractable cam with car door locking, to ensure correct operation of the emergency procedure inmanual mode, we recommend the possibility of removing battery power (e.g. via a manual or time-operated switch) when the cabinhas been aligned with the desired floor manually: it will then be possible to open the doors manually without any problem.If the ECO+ card is not supplied with power from a battery (24 Vdc 4 Ah) via connector X5, the following situation will occur:1. If there is an automatic operator with off-floor locking, the car can be manually aligned only to the nearest floor, as the floorlock will be opened by the retractable cams which will be extended to their maximum length due to the removal of power:the doors can only be opened manually.2. If you have an automatic operator without off-floor locking, it will be possible to align the car with the desired floor using amanual procedure: the doors can only be opened manually. This is possible because the automatic operators without off-floorlocking are fitted with a standard mechanic/magnetic device which allows the retractable cams to remain closed.Fig. 2INSTRUCTION HANDBOOK CAR DOORSubject to change without notice!ENCodeVersionGM.2.001049.ENHCodeVersionDatePage3212.32.0230J20.01.2015116.1644.2 SAFETY CIRCUIT- The door contacts are prewired to a terminal plugwith screw terminals D2.- Safety contact ratings: Min. 5VDC - Max. 250VAC 2A.1 DIP-Switch setting has to be copied from the replaced board, see chapter 9: DIP-Switches.2 In case of need adjust the reference switch so, that switch and magnet are oppositeone each other when the door panels are closed (clearance between switch and mag-net should be 56 mm).3 The DIP Switch S1/1 (Test Button Operation) must be activated.56mm5.1 PREPARATION AND LEARNING OF DOOR PARAMETERSCarry out only in event of replacement.PE = Connect ground wire1 & 2 =Connect safety circuit wires5. EXCHA

WITTUR GM.2.001049.EN.01

Documents

Transcript of WITTUR GM.2.001049.EN.01