WIRING AND INSTALLATION INSTRUCTIONS - GO Lighting | LED ...€¦ · GO is not responsible for any...

WIRING AND INSTALLATION INSTRUCTIONS

GO LIGHTING TECHNOLOGIES INC.

1

IMPORTANT SAFETY INFORMATION

PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION

•BEFORE INSTALLING THIS FIXTURE OR DOING ANY MAINTENANCE, MAKE SURE TO TURN OFF THE POWER SUPPLY AT THE CIRCUIT BREAKER OR FUSE BOX.

•CHECK TO MAKE SURE THAT ALL FIXTURE CONNECTIONS HAVE BEEN PROPERLY MADE AND THE FIXTURE IS GROUNDED TO AVOID POTENTIAL ELECTRICAL SHOCKS.

•DO NOT HANDLE ENERGIZED FIXTURE WITH WET HANDS, WHEN STANDING ON WET OR DAMP SURFACES, OR IN WATER.

Due to constant product improvements and/or adjustments, actual unit may vary from what is represented in this document. Please use this document as a reference guide only and confirm actual details and/or dimensions with authorized GO Lighting personnel as needed. GO is not responsible for any lighting units damaged due to improper installation.

2

Unless the networking option has been specified, the unit is designed to operate under AC wall switch control.

Designed for use in 90-240V (Canada) or 90-277V (USA), 50-60 Hertz protected circuit (fuse box, circuit breakers) and 90 degree C rated supply wire.

CAUTION:

Risk of Electric Shock

RISK OF PERSONAL INJURY

READ ALL INSTRUCTIONS

SAVE ALL INSTRUCTIONS

Do not connect Triac Dimmer to the Line voltage

Dry location use only.

IMPORTANT SAFETY INSTRUCTIONS

3

IMPORTANT SAFETY INSTRUCTIONSTHIS LUMINAIRE MUST BE MOUNTED OR SUPPORTED INDEPENDENTLY OF AN OUTLET BOX

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED

FOR CABLE USE ONLY – NOT FOR PULLING WIRES

CAUTION: DO NOT APPLY FORCE OR WEIGHT TO ANY INTERNAL WIRING OR DAMAGE TO THE UNIT MAY OCCUR. DO NOT SUSPEND THE JUNCTION BOX BY ANY OF THE INTERNAL WIRING DURING INSTALLATION. DO NOT PULL OR HOLD THE LUMINAIRE BY ANY OF THE ACCOMPANIED WIRES OR CABLES.


4

5

ELECTRICAL BLOCK DIAGRAM

90 – 300 VAC

24VDC

VOLTAGE IS ADJUSTED PER LED Vf

ECB-8.5MECB-2AC OR OR

CONTROLLER MODULES

SDVN-LVOR

PSUUL CLASS 2

LIGHT SOURCE

CONTROLLER

24VDC

LED PCB

LED PCB

LED PCB

LED PCB

WALL MOUNT

CONTROL

ECB-8.5S


5

6

WIRING


6

7

ASSEMBLY – HOUSING

PWR

24 VDC

90 – 277 VAC (White and Black wires)

ROUTE AC WIRES THROUGH Knockouts

Figure 3a

Ground wire (Green)connect PSU GND wire (green) to J-BOX housing and supply GND – See Figure C for details

AC SUPPLY WIRE


7

8

GROUND WIRE CONNECTION

Figure C


8

9

AC WIRE ISOLATION

CONTROL MODULE

PSU

ALL AC WIRES MUST SIT INSIDE THIS COMPARTMENT


9

10

0-10VDC WALL MOUNT CONTROL (SDVN) - WIRING

SDVN0 – 10V WALL MOUNT

CONTROL

VDC +

VDC -

Non-Ergonomic Wiring


10

11

NETWORKING – NON-ERGONOMIC – SDVN-GL

CN

2

CN

2C

N 2

CN

2

SDVN-GL PCBSDVN-GL PCB

SDVN-GL PCB SDVN-GL PCBC

N 2

SDVN-GL PCB

0 – 10 VDC WALL MOUNT CONTROL

CN 2 SDVN-GL


11

12

Ergonomic Wiring

Dimmer1: 0-10 VDC

Dimmer 2: 0-10 VDC

A

B

A

B

Dimmers

A

B 0-10V dimmer use purple wire

0-10V dimmer use grey wire

CONTROL BRIGHTNESS

CONTROL CCT

COLOR TERMINALCLOSE – CENTRE – 50% COLD + 50% WARMOPEN – ALL COLD OR WARM

INTENSITY TERMINALOPEN – FULL LIGHT LEVELCLOSE – NO LIGHT

SW 1 SETTING

SW 1

DIMMERM/S

MASTER PCB


12

13

IR SENSOR

M/S

MASTER PCB

SIGNAL - RED

+5V - WHITE

GND (SHIELDED AND YELLOW)

VDC +

VDC -


13

14

+ 24V

Signal

GND

Daylight Photodetector Sensor

DIMMERM/S

MASTER PCB


14

15

+ 24V

Signal

GN

D

Occupancy

DIMMERM/S

MASTER PCB


15

16

NETWORKING – ERGONOMIC

DIMMERM/S

MASTER PCB

M/S

SLAVE PCB

M/S

SLAVE PCB

M/S

SLAVE PCB

M/S

SLAVE PCB

DIM 1DIM 2


16

17

DIMMERM/S

MASTER PCB

M/S

SLAVE PCB

Master/SlaveComms Port

NETWORKING – ERGONOMIC


17

DOWN LIGHT

19

DOWN LIGHT WIRING


LED DRIVER

0-10VDC WALL MOUNT CONTROL

90-277 VAC

18

20

FLL – FLAT PANEL WIRING


LED DRIVER

0-10VDC WALL MOUNT CONTROL

90-277 VAC

WHITE WIRE

LED FLAT PANEL

19

347VAC ELECTRICAL 347 VAC

24VDC

PS

UIP

8424

GN

D

SD

VN

CO

NTR

OLLE

R

24VDC

LED PCB

LED PCB

LED PCB

LED PCB

LIGHT MODULE

WALL MOUNT

CONTROL

NOTE:1. WHITE WIRE

347VAC to 240VAC TRANSFORMER

LINE

NEU

TRA

L

POS (+)

NEG (-)

GN

D


20

Light fixture

SUSPENSION KIT – GSK1

4 per ASSY.2 per ASSY.


Please note that Suspension Kit options are highly customizable and what is represented here is merely the most common application. Please contact an authorized GO Lighting representative to discuss specific suspension kit options for your application.

21

WIRING AND INSTALLATION INSTRUCTIONS - GO Lighting | LED ...€¦ · GO is not responsible for any...

Documents

Transcript of WIRING AND INSTALLATION INSTRUCTIONS - GO Lighting | LED ...€¦ · GO is not responsible for any...