instructables

Wine Barrel Adirondack Chair

by GettingRad

Adirondack Chairs are comfortable, iconic lawn furniture that are timelessly popular. By using barrel staves youcan build a unique adirondack at an affordable price. Additionally, the compound curves of the staves themselvesgenerate make for a very comfortable chair.

Wine Barrel Adirondack Chair: Page 1

Step 1: Tools and Materials

Materials:

1. One wine barrel - both of my chairs used 25 staves - the hoops and heads were not used2. .5 lb Stainless Steel Finish Head Deck Screws3. Wood Sealer

Tools:

1. Pliers - End cutting pliers/nippers work well2. Hammer or Mallet - for removing hoops3. Chisel or screwdriver - for removing hoops4. Drill5. Measuring Tape6. Pencil7. Saw - I used a band saw and chop saw but a hand saw would work just as well though it may take

longer

Choosing a wine barrel

My preference if for red wine barrels with light or medium toast. The oak sucks up the color from the wine andturns a beautiful purple. I didn't have any red wine barrels available at the time of making this so I used white winebarrels. Whiskey, rum, tequila, etc. barrels will work as well but most are heavily charred on the inside. This meansyou will need to remove the char in order to have a clean surface. A high buildup finish - like spar varnish - can beused to seal the char so you don't turn black when you sit in your adirondack.

Finding barrels

The best way to get a barrel is to go straight to the source. If you have a local winery, call them and ask if they sellspent barrels. Be honest about the use. They may have an old dried out barrel kicking around as a table or parkingbarricade they may be willing to part with. Remember - you don't need anything that will hold liquid so it can besuper gross and old.

If you don't have any wineries nearby, try calling a Brewery or distillery. Many use wine barrels to impart differentflavors in their beer or spirits but, like at wineries, these barrels have a limited lifespan. At some point even thebest cared after barrel will become a 'garden barrel.'

If neither of these are options, some garden stores or home improvement stores stock barrels as garden art,planters or rain barrels. There are also some online resellers but I would use them as a last resort. From what Ihave seen, these last options seem to be the most expensive and shipping barrels isn't cheap.

Wine Barrel Adirondack Chair: Page 2

Step 2: Remove the Barrel Hoops

First, remove the hoop nails. These can be pried outwith end cut nippers. Stubborn ones might needsome coaxing with a chisel or screw driver.

Once the nails have been removed the hoops shouldslide off with a tap of the chisel. When the last hoopcomes free the barrel will collapse into a heap.

You will not need the hoops or heads for this projectbut they may be useful for building something elselike a mobile, wreath or tiny Dyson Ring.

I plan on using the leftover hoops, staves and barrelhead to build side-table to go with your chairs.

Wine Barrel Adirondack Chair: Page 3

Wine Barrel Adirondack Chair: Page 4

Step 3: Choose Your Staves

Lay out your staves. Set aside one wide stave for the middle of the back. Set aside the the stave with the bungholefor the face of the seat.

2 of the widest staves for the arms2 wide staves for the front legs2 wide staves for the rear legs/seat support. The more bent these are the more rounded your seatwill be.

The remaining staves can be paired up by width to make

6 staves for the backrest5 to 6 staves for the seat2 staves for the leg bracing3 staves for the back support

The inside of the barrel may be cracked or blistered. It probably goes without saying but try to select the staveswith the best insides for the seat and back. It will save you time sanding and finishing later. The legs and supportswill be less visible and are a better use of less pretty staves.

Lightly sand the outside of the staves to clean up the exterior. I only used a quick pass of 120 grit sand paper. Ididn't want to remove too much of the staining from the hoops.

You may need to sand the inside more aggressively. On several very bad staved I used the wood eraser (AngleGrinder with 24grit sanding pad). Working up to 120.

Wine Barrel Adirondack Chair: Page 5

Step 4: Cut Staves to Length

The approximate lengths for the legs, seat andsupports are in the photos. Since every barrel isdifferent, your lengths may be a little different frommine. I am about 5'11" and the seat fits me well. Itwas, however, a little big for shorter people.

The arms and back are full length staves.

The compound cure and inherent variation of thestaves makes for nice lines and a comfortable seatbut it also make joinery difficult. In the end each joint,cut and angle will need to be visually inspected tomake sure it looks right. Perfect joints are notpossible without lots of carefully cut curves. I declined

to make the joints perfect and instead simply miteredthe angles so they would be close. The gaps gnaw atmy joinery neurons but don't affect the comfort.

When cutting the staves - ALWAYS BE SAFE.

They will not lay flat like normal dimensional lumberand can be difficult to support. When cutting the pieceshould be supported very close to the blade toprevent kickback or binding.

Lay out your pieces like an exploded diagram. Makesure you have paired up similar sized pieces.

Wine Barrel Adirondack Chair: Page 6

Wine Barrel Adirondack Chair: Page 7

Step 5: Assemble the Back

Lay out the back. Pre-drill holes at the intersections of the back and support. I put two screws in the outer andmiddle stave for extra torsional support.

Screw the staves together. Add the second screw to the wider staves to help with torsional stability.

Step 6: Assemble the Seat

Arrange the staves for the seat. Start at the front edge of the chair and work your way back to where the seatintersects the back. The last stave will rest against the back of the chair.

The seat should be about 16"-18" deep.

Pre-drill the holes and screw in place.

Wine Barrel Adirondack Chair: Page 8

Step 7: Join the Seat and Back

Screw the seat to the back by drilling through the leg and into the lower back support. Be careful not to split thewood. The back and legs can exert a lot of torque on the screws until the rest of the supports are in place.

Wine Barrel Adirondack Chair: Page 9

Step 8: Add Legs and Arms

This is perhaps the most difficult step. I turned the chair on its side and dry fit the legs and arms on the ground,marked the point to drill and then screwed them in place.

Drill through the face of the front leg into the end of the rear leg. Repeat the process on the other side.

Step 9: Final Touches

The last pieces to be installed are the face of the seatand the leg braces.

The face stave with the bung hole can easily bescrewed into place from behind. Make sure to use atleast two screws in each side to keep the chair fromtwisting.

Hold the leg braces in place and scribe the angles inthe wood. Trim the pieces to fit the angles scribedand screw in place.

Make sure all your joints are sturdy and give yournew chair a test ride. The oak is hard and you mayfind that the corners are too sharp. If this is the case,hit the edges with your sander to round them over abit.

You will notice the stave in my hand still has char andsome yeast on it. I made sure to it up before using.

Wine Barrel Adirondack Chair: Page 10

This is an awesome project. Any suggestions on where to get a barrel?

Step 10: Finishing

You will likely want to seal the chair to keep them looking nice. I used a rattle can of Clear Tompson's Water SealIt slightly enhances the color and will help prevent water from soaking into your new chairs.

Since I got the barrels for free the total cost was about $13.

1 5/8" - Deck screws - $6

Thompson's Water Seal Can - $7

Wine Barrel Adirondack Chair: Page 11