WG43 indesit
Transcript of WG43 indesit
-
7/28/2019 WG43 indesit
1/39
Model type:
WG43TXGI
Commercial code:
12839 18025
-
7/28/2019 WG43 indesit
2/39
mod.WG43TXGI page 2
General notes
Technical Documentation guidelines
----------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------
You can find herewith some generic information to simplify cunsulting of technical documentation:
1. Models of same range share the same exploded views, which report the richest set of spare parts:generally, a model does not
necessarly have a related spare part for each particular shown on exploded views.
2. Some spare parts can not be represented directly on the exploded views (instruction booklets, specific kit, etc...). You can find
those codes in the spare parts list with the same reference of particular where spares are installed or with references 099, 999.
Instruction booklets, once managed, appear with 000 reference.
3. On the higher right site of each exploded view there is a serial number which indicates the beginning of the production of
certain range:some models might have more than an exploded view for a given category, each distinguished by a different serial
no.and linked to another spare parts list, In this case, serial no. is required to supply the right spare part code. Exploded view to be
considered is the one with a more recent serial no. but previous than the one of the model that needs assistance.
4.Exploded views might require further updates even after publishing. Addition of new spares will go on following the already
existing numeration references. Revision number of an exploded view is shown into last four digits of serial number into upper
right hand corner.
5.The spare parts list associated to an exploded view shows related codes of spares managed for a certain model; for each spare
part other informations are available:
REF: reference no of spare into a table; SUBSTITUTE: list of spare(s) which can replace a code but that keeps same functional
characteristics
INDUSTRIAL CODE: list of variables of a model (shown into model label) where such spare is used; NOTICE: code of
information(s) to refer to complete technical intervention, track for changes or to find correct spare part code.
6. Some notices, into a same section are generic therefore cannot be directly linked to a spare part. In order to assist a model in
the best way as possible, it is helpful to pay attention to all notices and constantly verify documentation updates
7.Technical documentation cover shows model name and its commercial codes
-
7/28/2019 WG43 indesit
3/39
mod.WG43TXGI page 3
1110010 Exploded views
-
7/28/2019 WG43 indesit
4/39
mod.WG43TXGI page 4
1110010 Spare parts list
Ref. Code . Substitute Description Notice Industrial
000 C00046972 m8x18
-
7/28/2019 WG43 indesit
5/39
mod.WG43TXGI page 5
1110150 Exploded views
-
7/28/2019 WG43 indesit
6/39
mod.WG43TXGI page 6
1110150 Spare parts list
Ref. Code . Substitute Description Notice Industrial
000 C00047551 user istructions booklet it
001 C00046947 1 x C00066277 27 giugiaro
001 C00066277 . 27 giugiaro
002 C00044900 ,
003 C00047565 control panel + handle giugiaro n1040013
005 C00046945 b.27 giugiaro
006 C00046946 . 27 giugiaro 0111098
006 C00055474 / 0111098
008 C00046944 1 x C00044735 push button knob white giugiaro
011 C00046923 1 x C00048002 cabinet white 27 giugiaro 0111131
n1040058
011 C00053781 1 x C00064546 cabinet white 27 kit n1040058
1 x C00065832
011 C00066276 27 2 n1040200
011 C00083796 . n1040200
013 C00037225
013 C00046953 1 x C00058449 inner door frame 0111125
013 C00057570 . giugiaro 0111131
013 C00058690
014 C00045244 giugiaro
015 C00045243 giugiaro
016 C00046950 giugiaro
017 C00046955 . giugiaro
018 C00046954 1 x C00058449 outer door frame 0111125
018 C00057569 . 27 0111131
019 C00047092 27 giugiaro
020 C00046951 .
029 C00047088 1 x C00046121 foot
1 x C00050320
032 C00043636 0111125
032 C00057567 . 0111125
033 C00046949
036 C00044085
038 C00046924 27
045 C00050182 . wgs / wg 0111131
-
7/28/2019 WG43 indesit
7/39
mod.WG43TXGI page 7
1110150 Spare parts list
Ref. Code . Substitute Description Notice Industrial
046 C00058692 . giugiaro
048 C00057571
049 C00058702
051 C00058689 . 27
099 C00040932 m6
099 C00044115 l = 34 mm
099 C00044116 bolt m8 x 55
099 C00076402 panel paraspray
-
7/28/2019 WG43 indesit
8/39
mod.WG43TXGI page 8
1110210b Exploded views
-
7/28/2019 WG43 indesit
9/39
mod.WG43TXGI page 9
1110210b Spare parts list
Ref. Code . Substitute Description Notice Industrial
001 C00034335 n1040259
002 C00034337 10,5 x 21 n1040259
003 C00034336 d33xd9xsp2 n1040235
004 C00040902 3l 496 0111086
0111093
004 C00047118 3lx tem 1196 0111093
004 C00053714 l 1110 j4 / 1106 0111093
005 C00053721 0111093
005 C00104529 0111093
006 C00047110 1 x C00058523 . 2 f.th 1
1 x C00103440
007 C00040130 : ++
008 C00041548 1 x C00143826 400-500
009 C00103637 d=
010 C00036059 400-600-800-1000 obg
011 C00104428 1 x C00014855 m8x80
012 C00104364
013 C00047136 1 x C00144571 romob m8
014 C00037346
015 C00046943 "wg834txi"
016 C00047133 . . 0111097
017 C00047087
018 C00039303 bolt l=55
020 C00046957 .
021 C00047099 obg 0111074
022 C00032708 plastic insert nut - case front
022 C00046961
023 C00103656 . .
024 C00040621 m4 x 50
024 C00104367 obg
025 C00046942
026 C00046962 giugiaro
028 C00034314 1 x C00104597
029 C00034315 1 x C00040888 saddle - damper spring clamp
030 C00039308 bolt l=50
-
7/28/2019 WG43 indesit
10/39
mod.WG43TXGI page 10
1110210b Spare parts list
Ref. Code . Substitute Description Notice Industrial
031 C00034316 1 x C00029588
032 C00104488 self locking nut m8
034 C00040901
035 C00047119 400g.(20406)h=56 mm
036 C00103642 l5
037 C00020181
037 C00103677
038 C00046972 m8x18
039 C00041843 8,5x17x1,5
041 C00040888 - ,
042 C00055397
-
7/28/2019 WG43 indesit
11/39
mod.WG43TXGI page 11
1110310a Exploded views
-
7/28/2019 WG43 indesit
12/39
mod.WG43TXGI page 12
1110310a Spare parts list
Ref. Code . Substitute Description Notice Industrial
001 C00019740 14mf 8 micron n1040058
n1040073
001 C00074642 + 14 mf
002 C00047115 1 x C00026359 radio interference suppressor n1040058
002 C00065987
003 C00003103 1 x C00022357 supply cable n1040058
003 C00064563 3x1 schuko 1,5 m
004 C00047111 1 x C00049312 wiring + timer elbi 5000 0678 n1040073
004 C00074678 wiring + timer elbi 5000 0678.a
005 C00030358 .-. -
005 C00031061 nc
006 C00019749
008 C00041163 terminal block
009 C00047114 elbi 5000 0678-0003 0111060
009 C00049196 elbi 5000 0678(60411 0111060
n1040073
009 C00065975 elbi 0748/1.a/2.a n1040178
010 C00019650
010 C00047062 0111098
011 C00047109 1 x C00052621 1 210 / 95 0111060
011 C00048195 1-. 0111060
012 C00047066
013 C00047069 1 x C00097834
014 C00047068 1 x C00075352 detergent drawer
015 C00034325 1 x C00103834 pressure switch hose l 560 mm
017 C00011140
019 C00103883 1-. 117
020 C00046976 2000 230
021 C00040931
023 C00047117 1 x C00053714 motor 2/12 poles 0111093
1 x C00053721
1 x C00054724
023 C00054724 2/12 . 0111093
024 C00104675
025 C00047173 seal m5
-
7/28/2019 WG43 indesit
13/39
mod.WG43TXGI page 13
1110310a Spare parts list
Ref. Code . Substitute Description Notice Industrial
025 C00047174 m 5
027 C00034332 bracket - heater element/tub
029 C00027466 .
030 C00026616 1 x C00015498 hose - valve/dispenser (hot)
031 C00019902 . .
032 C00003070 . 1500 mm
034 C00005572
036 C00028568
037 C00019708
038 C00028569
039 C00047067
040 C00019732 hc
041 C00047065 1 x C00052771 hopper
042 C00046980 8lt/1 220
052 C00044998 . . 240
053 C00050197
-
7/28/2019 WG43 indesit
14/39
mod.WG43TXGI page 14
Notices
0111060: MODIFIED ELBI 5000 0678 TIMER
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
As from serial no. 60411.0001, ELBI 5000 0678 timer and relevant wiring have been modified and pressure switch code 047109
without overflow (excepting in the case of model WG625SK) is used on 400 and600 rpm washers in the Giugiaro range.
Modified timer code 049196 refers to drawing number 160004008.07
printed on the data plate on the timer.
The new timer may be used to replace the premodification timer (drawing number 160004008.03 printed on the data plate on the
timer)
only if mounted with the modified wiring and pressure switch code
047109 (excepting in the case of model WG625SK).
Timer code 047114 and pressure switch 048195 will be supplied normally.
0111074: MODIFIED GIUGIARO DOOR SEAL
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 61212.0001, a new seal will be used with a thicker front lip, on all of the round glass doors on the
Giugiaro washing machines produced at the Teverola factory, in order to increase adherence between the seal and the door, to
eliminate any water leaks.
The new seal will have the same code no. 047099, as the pre- modification component.
0111086:
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
In order to eliminate the noise made by the slipping of the belt on the pulleys on the 400 r.p.m. washing machines with the
standard cabinet, the belt must be replaced, using the one with code number 040902.
0111093: MODIFIED MOTOR, PULLEY AND BELT
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-
7/28/2019 WG43 indesit
15/39
mod.WG43TXGI page 15
Beginning with serial no. 70908.0001 on the 400/500/600 rpm washing machines produced at the Teverola plant (except model
WG620G from serial no. 70901.0001), the motors, drive pulleys and belts have been changed.
The new parts are:
400/500 rpm Models:
Cod. 054724 - Motor: 2/12 poles;
Cod. 053721 - Driven pulley;
Cod. 053714 - Belt: CINGHIA L 1110 J4
600 rpm Models:
Cod. 054723 - Motor: 2/16 poles;Cod. 053721 - Driven pulley;
Cod. 053714 - Belt: CINGHIA L 1110 J4
WG620G
Cod. 056521 - Motor: 2/16 poles;
Cod. 053721 - Driven pulley;
Cod. 053714 - Belt: CINGHIA L 1110 J4
The modified parts are interchangeable with the pre-modification ones, only if used as a complete assembly; the pre-modification
parts will continue to be handled normally.
0111097: CODIFICATION OF CROSS-SUPPORT FOR CABINET
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
There have been requests for the following part, which was not previously supplied, but which is now coded.
The new code is as follows:
Code 055397 - support cabinet
This part is now available from our Centralised Spare Parts
Warehouse.
0111098: UNIFICATION OF THERMOSTAT AND POTENTIOMETER
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 71110.0001 for the washing machines produced in the Teverola factory, the parts already in use at the
Comunanza factory will be used, (where appropriate) in order to unify the component parts utilised in production.
The parts concerned are as follows:
.ps
Part no. 019650 - Adjustable Thermostat;
Part no. 046981 - Spin Potentiometer;
Part no. 014917 - Thermostat Seal;
The use of these parts necessitated the modification of the knobs and in some cases the control panels.
The new knobs are not interchangeable with the previous ones therefore, they have been given new part numbers.
The new control panels + handles however, can be used on the pre-modification appliances (without having to change the knobs).
The only exceptions are the following models:
WG835TXR, WG834TXI, WG838TXE and WN880XWE/S, where the new control panels had to be re-coded and the new
potentiometer used with the relative knob.
The part numbers for the new control panels are:
Part no. 055584 - Control panel + handle WN880XWE/S;
Part no. 055577 - Control panel + handle WG835TXR;
Part no. 055581 - Control panel + handle WG834TXI;Part no. 055583 - Control panel + handle WG838TXE.
-
7/28/2019 WG43 indesit
16/39
mod.WG43TXGI page 16
0111125: DOOR HINGE MADE OF METAL SHEET
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 80703.0001 on models that use the door with part no. 001459, a steel hinge with part no. 057567, a new
door with part no. 057573 and screws to fasten it (part no. 057568) have replaced the previous pieces.The new hinge can be used on pre-modification appliances only if they use the new door and screws.
The new door can be fitted onto the earlier aluminium hinge, part no 043636, but only if the screws used to fasten it have part no.
057571.
0111131:
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 81020.0001 on some of the washing machine models produced in the Teverola factory, the door with
the center handle is being used(in line with the hinge).
This modification affects the following parts:
Part no. 051926 - Giugiaro cabinet;
Part no. 058692 - Door handle kit with Giugiaro restyling;
Part no. 058702 - Complete Giugiaro door;
Part no. 058689 - Giugiaro door frame;
Part no. 058690 - Inner frame.
Said modification also entails a change in the commercial codes, as indicated below:
Serial no. 81020.00001 Mod. W415TPDI - Com. code changes from 16938 to 18032;
Serial no. 81020.00001 Mod. W535TPI - Com. code changes
from 16942 to 18036;Serial no. 81021.00001 Mod. WG430TXEI - Com. code changes from 12837 to 18023;
Serial no. 81022.00001 Mod. WG630TXI - Com. code changes from 08442 to 18018;
Serial no. 81022.00001 Mod. WG425PI - Com. code changes from 16939 to 18033;
Serial no. 81022.00001 Mod. WG437TPEI - Com. code changes from 16940 to 18034;
Serial no. 81023.00001 Mod. WG43TXGI - Com. code changes from 12839 to 18025;
Serial no. 81023.00001 Mod. W44TXDI - Com. code changes from 13738 to 18027;
Serial no. 81023.00001 Mod. WG636TPI - Com. code changes from 16869 to 18030;
Serial no. 81023.00001 Mod. WG635TXEI - Com. code changes from 12838 to 18024;
Serial no. 81024.00001 Mod. W44TXDI - Com. code changes from 13738 to 18027.
n1040013: New Indesit logo
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 90301.0001, a new logo (as shown in the figure) will be printed or silk-screened on the control panels
and the manuals for the Indesit washing machines and washer-dryers.
The new parts will be handled with the same SAT numbers as the pre-modification parts (which will be eliminated).
-
7/28/2019 WG43 indesit
17/39
mod.WG43TXGI page 17
n1040058: Various modifications (Plastic tub without safety thermostat hole, new supply cable and radio
interference suppresser complete with terminal board).
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 00110.0001, a few modifications have been made to washing machines manufactured at the Teverola
factory. These modifications mainly affected the cabinet (on which the perforation of the terminal board was modified) and the
tub (from which the hole and the safety thermostat were removed) and a new heating element with fuse was used.
The new parts, except for the worktop, cannot be used on their own on pre-modification appliances because the cabinet has to
have the supply cable moulded together as well as the radio interference suppresser and the quick connection condenser, whereas
for the tub it is absolutely necessary to use the heating element with fuse.
However, to carry out this intervention, the wiring needs to be modified in the following way:
1) Discard the wire leading from the safety thermostat to the heating element.2) Disconnect the wire that leads from the wiring to the safety thermostat and insert it onto the contact of the new heating element
on which the fuse is placed (it can be recognised by the green insulating sheath on 230 V models and the blue one on 240 Volt
models).
The pre-modification parts shall continue to be handled until stocks run out.
The following table has been attached in order to make it simpler to identify the parts necessary for the use of a new cabinet or of
a new tub on pre-modification appliances.
-
7/28/2019 WG43 indesit
18/39
mod.WG43TXGI page 18
-
7/28/2019 WG43 indesit
19/39
mod.WG43TXGI page 19
n1040073: ELBI Standardised Timer on 400-600 rpm appliances from Teverola
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Beginning with serial no. 00420.0001, the new ELBI standardised timers have been used on 400-600 rpm Washing machines
manufactured at the Teverola factory (both with plastic and stainless steel tub), (00714.0001 - WG522TXU- 46180660100) , with
the exception of models from the LB2000 range which were manufactured using the new timer from the very beginning.
In connection with the use of this new timer, condensers complete with fixing brackets have been used and a hole was pierced
into the cabinets for the hardware key as well as suitable cutting for the condenser fixing bracket housing.
The part nos. for the parts used for the modification, excluding the wiring assemblies (they appear in the documentation of the
respective models) are the following:
ELBI standardised timers:
Part no. 065975 - ELBI Timer 0748 fonly for Service.
The timer SAT must be used in place of the following timers, making sure that
during the connection the wiring harness connectors are not rotated at 180 degrees.The connectors must be inserted in respect to their correspondence to the letters noted on the lower right side of the timer, without
respecting the terminals.
-
7/28/2019 WG43 indesit
20/39
mod.WG43TXGI page 20
ELBI 0748/1.A (yellow plate) ;
ELBI 0748/2.A (blue plate);
ELBI 5000 0678.A Standardised (white plate);
ELBI 5000 0698.A Standardised (red plate);
ELBI 5000 0698/3.A Standardised (white plate with red band).
Condensers:
Part no. 074642 - Condenser + bracket 14 mF;Part no. 074643 - Condenser + bracket 16 mF;
Part no. 074644 - Condenser + bracket 12,5 mF.
Pressure switches
Cabinets:
Part no. 066276 - White cabinet 27 two holes electrovalve for ranges A-AF-BAMR-HL-IW-LRE-W-WG-WH-WN-;
Part no. 066507 - Brezil cabinet for range AF;
Part no. 066275 - White cabinet 27 for range WGS.
Part no. 064899 Serial port test plug for cabinet.
The timer 065975, if used instead of the pre-modification one requires without exception the replacement of the wiring assembly,
therefore the pre-modification timers (part no. 049196, part no. 049378 and part no. 053719) will continue to be handled normally.
The new condensers are not interchangeable with the pre-modification ones (part no. 019740, part no. 013582 and part no.
036121), therefore both those with and those without fixing bracket are handled.
The modified cabinets will keep the same part number as the pre-modification ones.
All the wiring assemblies will only be handled upon request and therefore warehouse stocks are not planned.
n1040178: Timer ELBI 0748 green label specifically for the SAT.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
The timer code 065975 that is forwarded as a spare part, is used exclusively for After Sales Service.
This particular item is handled in place of the five timers used in production, and differs not only aesthetically but also in function
as it combines all the operations.
Please be aware of the following, in the employment of the timer Code 065975 - Timer Elbi 0748 Green Label for SAT :
1) Do not rotate the wiring harness connectors at 180 during the connection;
2) The connectors must be inserted in respect to their correspondence to the letters noted on the lower right side of the timer,without respecting the terminals.
3) The SAT timer is mounted without any modification performed on apparatus that employ a timer without a distribution lever.
Rationalized Elbi Timers.
The SAT timer, is used in place of the following timers:
ELBI 0748/1.A (yellow label) the distribution lever is not employed;
ELBI 0748/2.A (blue label) the distribution lever is not employed;
ELBI 5000 0678.A Rationalized (white label);
ELBI 5000 0698.A Rationalized (red label);
ELBI 5000 0698/3.A Rationalized (white label with red band).
-
7/28/2019 WG43 indesit
21/39
mod.WG43TXGI page 21
n1040200: Electrovalve drill hole plug for Teverola production cabinets.
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
From the registration no. 10601.0001 on all Washing machines produced in the Teverola plant have been using cabinets with two
electrovalve drill holes.If the model produced provides for one only electrovalve, then one drill hole is capped by using the appropriate plug code
083796.
The cabinets handled by After Sales Service with two electrovalve drill holes where used on models with one only electrovalve
should use the plug.
n1040235: Restored the fixing of the anterior counterweight with platelets inserted in the tub-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
From the 11105.0001 registration number on the washing machines with plastic tubs produced in the Teverola factory, the fixing
of the anterior counterweight is restored with platelets inserted in the tub instead of those realised with self-threading screws, the
system described in Notice N1040184.
The tubs maintain the same SAT code and are provided with the following particulars:
N 3 Screws code cod. 014342;
N 3 Conical washer cod. 055018;
N 3 Plain washer cod. 034336.
Whenever the necessity may arise on a tub, proceed with diverting the self-threading screws that block the anteriorcounterweight., as it's compulsory to execute the fixing again avoiding in time a possible loosening and thus the breaking of the
tub by utilising the registered screws (cod. 014342), the conical washers (cod. 055018), the plain washers (cod. 034336) and the
platelets (cod. 055038).
-
7/28/2019 WG43 indesit
22/39
mod.WG43TXGI page 22
Electric schemes and links
Cod. 111167a
-
7/28/2019 WG43 indesit
23/39
mod.WG43TXGI page 23
Legend
Legend: 111167a
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC Blocco Cesto NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer P Pressure switch
BP Buzzer P1 1st level pressure cut-off switch
C Condensator P2 2nd level pressure cut-off switch
CA Condensator PA High speed potentiometer
DV Switching device PB Low speed potentiometer
EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool
EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector
EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch
ER Exclude Heating Element PS Drain pumpET Thermostat disactivation R Heating element
EV Electrovalve RE Relay
EVA Dryer electrovalve RR Heating element
EVC Hot water electrovalve RV Speed regulator
EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element
EVL Wash electrovalve S LED
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
I1..2..3.. Switches/switching devices TA Drying timer contacts
IA Switch On/Off TB Low Temperature Thermostat
IC Switch N.C. - 1/2 Load TC Spider wheel earth
ID Switch display TFL Flange earth
IE Water Saving Device TG Main earth
IF Switch - Spin Reduction TH Thermostat
IP Door switch TH1 1st temperature thermostat
IR Line switch TH2 2nd temperature thermostatIS Water-stop TH3 3rd temperature thermostat
-
7/28/2019 WG43 indesit
24/39
mod.WG43TXGI page 24
L Line or Lamp THF Operating thermostat
LB Low Level THR Adjustable thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
-
7/28/2019 WG43 indesit
25/39
mod.WG43TXGI page 25
Electric schemes and links
Cod. 111168b
-
7/28/2019 WG43 indesit
26/39
mod.WG43TXGI page 26
Legend
Legend: 111168b
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC Blocco Cesto NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer P Pressure switch
BP Buzzer P1 1st level pressure cut-off switch
C Condensator P2 2nd level pressure cut-off switch
CA Condensator PA High speed potentiometer
DV Switching device PB Low speed potentiometer
EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool
EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector
EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch
ER Exclude Heating Element PS Drain pumpET Thermostat disactivation R Heating element
EV Electrovalve RE Relay
EVA Dryer electrovalve RR Heating element
EVC Hot water electrovalve RV Speed regulator
EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element
EVL Wash electrovalve S LED
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
I1..2..3.. Switches/switching devices TA Drying timer contacts
IA Switch On/Off TB Low Temperature Thermostat
IC Switch N.C. - 1/2 Load TC Spider wheel earth
ID Switch display TFL Flange earth
IE Water Saving Device TG Main earth
IF Switch - Spin Reduction TH Thermostat
IP Door switch TH1 1st temperature thermostat
IR Line switch TH2 2nd temperature thermostatIS Water-stop TH3 3rd temperature thermostat
-
7/28/2019 WG43 indesit
27/39
mod.WG43TXGI page 27
L Line or Lamp THF Operating thermostat
LB Low Level THR Adjustable thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
-
7/28/2019 WG43 indesit
28/39
mod.WG43TXGI page 28
Electric schemes and links
Cod. 111168c
-
7/28/2019 WG43 indesit
29/39
mod.WG43TXGI page 29
Legend
Legend: 111168c
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC Blocco Cesto NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer P Pressure switch
BP Buzzer P1 1st level pressure cut-off switch
C Condensator P2 2nd level pressure cut-off switch
CA Condensator PA High speed potentiometer
DV Switching device PB Low speed potentiometer
EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool
EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector
EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch
ER Exclude Heating Element PS Drain pumpET Thermostat disactivation R Heating element
EV Electrovalve RE Relay
EVA Dryer electrovalve RR Heating element
EVC Hot water electrovalve RV Speed regulator
EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element
EVL Wash electrovalve S LED
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
I1..2..3.. Switches/switching devices TA Drying timer contacts
IA Switch On/Off TB Low Temperature Thermostat
IC Switch N.C. - 1/2 Load TC Spider wheel earth
ID Switch display TFL Flange earth
IE Water Saving Device TG Main earth
IF Switch - Spin Reduction TH Thermostat
IP Door switch TH1 1st temperature thermostat
IR Line switch TH2 2nd temperature thermostatIS Water-stop TH3 3rd temperature thermostat
-
7/28/2019 WG43 indesit
30/39
mod.WG43TXGI page 30
L Line or Lamp THF Operating thermostat
LB Low Level THR Adjustable thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
-
7/28/2019 WG43 indesit
31/39
mod.WG43TXGI page 31
Electric schemes and links
Cod. ce012100
-
7/28/2019 WG43 indesit
32/39
mod.WG43TXGI page 32
Legend
Legend: ce012100
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC Blocco Cesto NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer P Pressure switch
BP Buzzer P1 1st level pressure cut-off switch
C Condensator P2 2nd level pressure cut-off switch
CA Condensator PA High speed potentiometer
DV Switching device PB Low speed potentiometer
EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool
EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector
EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch
ER Exclude Heating Element PS Drain pumpET Thermostat disactivation R Heating element
EV Electrovalve RE Relay
EVA Dryer electrovalve RR Heating element
EVC Hot water electrovalve RV Speed regulator
EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element
EVL Wash electrovalve S LED
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
I1..2..3.. Switches/switching devices TA Drying timer contacts
IA Switch On/Off TB Low Temperature Thermostat
IC Switch N.C. - 1/2 Load TC Spider wheel earth
ID Switch display TFL Flange earth
IE Water Saving Device TG Main earth
IF Switch - Spin Reduction TH Thermostat
IP Door switch TH1 1st temperature thermostat
IR Line switch TH2 2nd temperature thermostatIS Water-stop TH3 3rd temperature thermostat
-
7/28/2019 WG43 indesit
33/39
mod.WG43TXGI page 33
L Line or Lamp THF Operating thermostat
LB Low Level THR Adjustable thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
-
7/28/2019 WG43 indesit
34/39
mod.WG43TXGI page 34
Electric schemes and links
Cod. lg001400
-
7/28/2019 WG43 indesit
35/39
mod.WG43TXGI page 35
Legend
Legend: lg001400
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC Blocco Cesto NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer P Pressure switch
BP Buzzer P1 1st level pressure cut-off switch
C Condensator P2 2nd level pressure cut-off switch
CA Condensator PA High speed potentiometer
DV Switching device PB Low speed potentiometer
EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool
EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector
EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch
ER Exclude Heating Element PS Drain pumpET Thermostat disactivation R Heating element
EV Electrovalve RE Relay
EVA Dryer electrovalve RR Heating element
EVC Hot water electrovalve RV Speed regulator
EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element
EVL Wash electrovalve S LED
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
I1..2..3.. Switches/switching devices TA Drying timer contacts
IA Switch On/Off TB Low Temperature Thermostat
IC Switch N.C. - 1/2 Load TC Spider wheel earth
ID Switch display TFL Flange earth
IE Water Saving Device TG Main earth
IF Switch - Spin Reduction TH Thermostat
IP Door switch TH1 1st temperature thermostat
IR Line switch TH2 2nd temperature thermostatIS Water-stop TH3 3rd temperature thermostat
-
7/28/2019 WG43 indesit
36/39
mod.WG43TXGI page 36
L Line or Lamp THF Operating thermostat
LB Low Level THR Adjustable thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer
-
7/28/2019 WG43 indesit
37/39
mod.WG43TXGI page 37
Electric schemes and links
Cod. se045700
-
7/28/2019 WG43 indesit
38/39
mod.WG43TXGI page 38
Legend
Legend: se045700
AQS Aquastop electrovalve Mzbn/MTA zbn timer motor
B Buzzer N Neutral or Terminal Board
BC Blocco Cesto NC Spin cycle exclusion
BF Terminal board contact, motor fan and dryer P Pressure switch
BP Buzzer P1 1st level pressure cut-off switch
C Condensator P2 2nd level pressure cut-off switch
CA Condensator PA High speed potentiometer
DV Switching device PB Low speed potentiometer
EF/CL Electro-Valve Cold Water / Bleach PL Pure Wool
EF/L Electro-Valve Cold Water / Wash PM Motor Thermoprotector
EF/P Electro-Valve Cold Water / Prewash PR Timer programmer or Pressure switch
ER Exclude Heating Element PS Drain pumpET Thermostat disactivation R Heating element
EV Electrovalve RE Relay
EVA Dryer electrovalve RR Heating element
EVC Hot water electrovalve RV Speed regulator
EVF Elettrovalvola acqua fredda Ras/RA Dryer heating element
EVL Wash electrovalve S LED
EVP Pre Wash electrovalve SL Line LED
FA Antijamming filter SO Door LED
FD Delicate drying cycle thermostat SR Heating LED
FE Strong drying cycle thermostat ST Temperature selector FRT Thermofusible Heating Element SV Speed Selector for Spin
I Inverter T Timer contacts
I1..2..3.. Switches/switching devices TA Drying timer contacts
IA Switch On/Off TB Low Temperature Thermostat
IC Switch N.C. - 1/2 Load TC Spider wheel earth
ID Switch display TFL Flange earth
IE Water Saving Device TG Main earth
IF Switch - Spin Reduction TH Thermostat
IP Door switch TH1 1st temperature thermostat
IR Line switch TH2 2nd temperature thermostatIS Water-stop TH3 3rd temperature thermostat
-
7/28/2019 WG43 indesit
39/39
L Line or Lamp THF Operating thermostat
LB Low Level THR Adjustable thermostat
LN Normal Level TM Motor earth
LS Pilot lamp TMB Main cabinet earth
M Earth-symbol TMP Motor thermal protector
MC Spin cycle motor TMS Thermostop
MI MOTOR WITH PULLEY TP Thermal protector
ML Wash cycle motor TPS Drain pump earth
MO Terminal Board TR Heating element earth
MP Door dip-switch TS Safety thermostat
MR Thermal Lock TT Timer earthing connection
MT Timer motor TTH Earthing Thermostat
MV Motor fan TV Tank earth
MV -Ras Dryer heating element ZBN Timer