WENDLAND MANUFACTURING CORPORATION

Product/Engineering Catalog

2004

601 West 11th Phone: (325) 655-6778 P.O. Box 808 Fax: (325) 655-0325 San Angelo, TX 76902 www.wendlandmfg.com

P.O. Box 808 Telephone: (325) 655-6778

San Angelo, Texas 76902 Fax: (325) 655-0325 E-Mail: [email protected] Web Site: www.wendlandmfg.com

& Atlanta Sales Office

P.O. Box 49083 Telephone: (404) 636-2028 Atlanta, GA 30359 Fax: (404) 325-5422

E-Mail: [email protected]

PRODUCTS MANUFACTURED BY WENDLAND MFG. CORP.

A.S.M.E. - U.L. - Standard Pressure Vessels - Atmospheric Storage Tanks

- WATER RELATED TANKS -

Hot Water Storage Tanks Hot Water Heater Tanks Expansion Tanks Flash Tanks Hydropneumatic Storage Tanks Water Filter Tanks

Fire Protection Tanks Condensate Receivers Boiler Feed Water Tanks Boiler Blow Down Tanks Make Up Water Tanks Deaerator Tanks

Chill Water Tanks

- OTHER PRESSURE TANKS -

Steam Accumulators Nitrous Oxide Tanks Freon Receivers Air Receivers Vacuum Tanks Separators Suction Scrubbers Acid Storage Tanks Stainless Steel Tanks Chemical Storage Tanks

- FUEL & ATMOSPHERIC STORAGE TANKS -

Overhead Farm Tanks Skidded Fuel Tanks

Water Storage Tanks

Oil Field Pressure Skid Tanks Misc. Chemical Storage Tanks

WENDLAND MANUFACTURING CORP. 1 10-01-2004

TABLE OF CONTENTS GENERAL:

History of Wendland Manufacturing Corporation...............................…............. 2General Information................................................................................….......... 2-3

LININGS:

Exterior Paint..............................................................................................…...... 4Hot Dip Galvanizing.......................................................................................….. 4Epoxy….........................................................................................................…... 4Cement...........................................................................................................…... 4AWWA Linings..............................................................................................….. 5Other Linings..................................................................................................….. 5Insulation and Metal Jacket…………………………………………………….. 5

WATER STORAGE TANKS:

General Information and Outline Drawings......................................................... 6 CHILL WATER STORAGE TANKS:

General Information and Outline Drawings......................................................... 7 WATER HEATERS:

General Information and Outline Drawings......................................................... 8 FIRE PROTECTION TANKS:

General Information and Outline Drawings........................................................ 9 HYDROPNEUMATIC STORAGE TANKS:

General Information and Outline Drawings........................................................ 10 AIR RECEIVER TANKS:

General Information and Outline Drawings........................................................ 11 CATALOG DATA INFORMATION SHEETS

Sizing Chart….............................................................................……..…........... 12-14 FLASH TANKS:

General Information and Outline Drawings........................................................ 15-16 EXPANSION TANKS:

General Information and Outline Drawings........................................................ 17-18 BLOW-DOWN TANKS

General Information and Outline Drawings........................................................ 19-20 AIR SEPARATOR TANKS:

General Information and Outline Drawings........................................................ 21-22

WENDLAND MANUFACTURING CORP. 1a 0-01-2004

TABLE OF CONTENTS ENGINEERING SPECIFICATION SHEETS:

Water Storage Tanks……………………………………………………………. 23Chill Water Storage Tanks……………………………………………………… 24-25Water Heater Tanks…………………………………………………………….. 26Fire Protection Tanks…………………………………………………………… 27Hydropneumatic Storage Tanks…………..………………………….…………. 28-30Air Receiver Tanks………………………………………………………….….. 31Flash Tanks………………………………………………………..……..…...… 32Expansion Tanks………………………………………………………..………. 33Blow-Down Tanks……………………………………………………...………. 34Air Separator Tanks……………………………………………………….……. 35

SUPPORT ACCESSORIES:

Skirt………….....................................................................…….....…................. 36Angle Leg Supports.....................................................................………………. 37Heavy Duty WFI Beam Supports......................................................….......…… 38Saddle Supports....................................................................................…....…… 39-40

MISCELLANEOUS:

Warranty Under 36” OD Vessel...............................................................……… 41Warranty Over 36” OD Vessel...................................................................…….. 42Operations and Maintenance Instructions………………………………………. 43-44Lifting and Handling Instructions………………………………………………. 45

PRICING: Main Pricing Page (Not viewable unless you have pricing pages)...................

WENDLAND MANUFACTURING CORP. 10-01-2004 2

HISTORY OF WENDLAND MANUFACTURING CORP.

For over 84 years, Wendland Manufacturing has provided quality tanks and pressure vessels to their suppliers and customers. Many of our representatives have been with Wendland for over 50 years. Mr. H.G. Wendland founded the company in 1921 doing mainly light gauge fabrication. After the death of Mr. Wendland in the early fifties, the company expanded its tank product lines from mainly oil field work to propane tanks and hot water tanks under the direction of J.R. Salmon and his sons. These tanks became the major product lines during the fifties and sixties. In the seventies and eighties, propane tanks were dropped from the line and the focus became the hot water storage tank industry, and in the nineties, the larger hydropnuematic storage tanks were added to the line. Today, Wendland manufactures an entire line of tanks and pressure vessels for the water, waste water, chemical, and numerous other industries along with a light gauge line for the oil markets. In July of 1998, Wendland Mfg. Co. became a wholly owned subsidiary of Burnham Holdings of Lancaster, Pennsylvania. The company name was changed to Wendland Manufacturing Corp. The

merger opened up new markets and introduced a new line of manufacturer’s representatives. Wayne McCune, who had directed the company since early 1997, was named President and General Manager. Under his management, new equipment was purchased, new products developed, and existing markets expanded. As a result, the labor force increased in size and sales increased. Together with the sales office in Atlanta, Georgia, the customer base for large hydropneumatic storage tanks and new customer accounts has dramatically increased. At Wendland Manufacturing Corp., the past has been good, but the future looks even better. The company is well situated to take advantage of important markets for the future. Water resource management is being accomplished by the use of Wendland water conditioning and water filter tanks. The hydropneumatic tank products have been expanded to meet the needs of municipal water districts and other waste utilities. With continued growth and expansion, Wendland truly represents the "can do" attitude and the "no job is too small" philosophy.

GENERAL INFORMATION Wendland Manufacturing created this catalog to assist the representative, architect, engineer or designer in selecting tanks for his/her needs. This catalog outlines only a few of the many standard tanks that we fabricate. Our standard vessel sizes are shown in table format for your convenience. The standard drawings are for customer convenience and should be used as a guide only. If you require, we can custom fabricate a vessel to your particular specifications and provide you with a custom drawing to your specifications. Wendland fabricates vessels to specifications of the two most commonly used tank standards. We fabricate A.S.M.E. Code vessels to requirements of

Section VIII, Division 1. In addition, we fabricate UL specification #142 for above ground installation. Also available is our standard non-code pressure tank built to your specifications. Wendland’s modern production facilities enable us to build a wide range of vessels. We can fabricate tanks from 10-gallon capacity to 50,000-gallon capacity or from one tank to any quantity you require. We have made a commitment to make the highest quality vessel available at an economical price and to give you the best service available in the industry. If required, Wendland will make every effort to assist you in formulating and writing a specification to meet your specific tank needs.


A.S.M.E. CODE TANKS & NATIONAL BOARD

REGISTRATION The American Society of Mechanical Engineers was established with the objective of formulating rules for fabricating pressure vessels, to afford reasonably certain protection of life and property and to provide a margin for deterioration in service so as to give a reasonably long period of safe usefulness. The A.S.M.E. Code governs the design material, fabrication, and quality control via an outside authorized inspection agency that oversees the A.S.M.E. Code vessel from start to completion by inspecting all processes. All Wendland Mfg. A.S.M.E. Code tanks are built in strict compliance to meet or exceed the A.S.M.E. Section VIII, Division 1 Code requirements. The tanks will be furnished with an A.S.M.E. Code nameplate, and we can furnish the customer with manufacturer’s data report verifying A.S.M.E. Code compliance. We can also register the tanks with the National Board of Boiler & Pressure Vessels if required.

U.L. STORAGE TANKS We also offer a U.L. labeled fuel storage tank, which is required by fire marshals of most municipalities. Underwriters Laboratories is an independent non-profit organization testing for public safety. This organization regulates material thickness, joint procedures and overall vessel design. We offer aboveground fuel storage tanks fabricated to U.L. specification #142. Our U.L. tanks are built under strict adherence to our Quality Control Department and meet all U.L. directives. Each U.L. tank is thoroughly inspected and tested prior to shipment. These tanks are intended for installation and use in accordance with NFPA30 and NFPA31 requirements of the National Fire Protection Association.

WENDLAND STANDARD PRESSURE TANKS

When the A.S.M.E. Code stamp is not required, Wendland can furnish a standard pressure tank of high quality built to your specifications. These tanks have sufficient safety factors and are hydrostatically tested at one and one half times the design pressure. Since these tanks are fabricated by the same personnel as the A.S.M.E. tanks, you can be assured that these vessels are built with the same welding procedures and meet A.S.M.E. Code quality. As a result of this, you will have a high quality tank at a more economical price than vessels built with the A.S.M.E. Code symbol. Wendland can also furnish you with a standard non-code pressure tank. These tanks also have sufficient safety factors and are air tested. These vessels are a quality tank at an economical price.


LININGS:

EXTERIOR PAINT

Unless otherwise specified, all vessel exteriors are prime painted before shipment. Prior to being painted, the vessel is cleaned of loose mill scale and rust with power grinders and power wire brushes. The vessel is then painted with one coat of Wendland standard shop primer. Sandblasting and most industrial and military specification exterior coatings are also available. Please consult the factory for this pricing.

HOT DIP GALVANIZING

For many years galvanizing has been popular for protecting steel water tanks. The zinc coating serves in twofold capacity. First, it protects the steel from corrosion as long as the zinc coating is unbroken. Second, due to the fact it is more electro-chemically active than steel, it sacrifices itself to protect the steel vessel even when moderate sized areas of bare metal have been exposed. Tanks to be hot dip galvanized are thoroughly cleaned; first by dipping in a caustic bath removing grease, oil and dirt, then by being dipped in a 12% solution of sulfuric acid removing rust and mill scale. The vessel is then rinsed and submerged in a liquid flux pre-dip. Finally, the vessel is immersed into the molten zinc at approximately 850° Fahrenheit to produce the finished product, which meets ASTM specifications. To have a successful galvanizing job, additional openings may be required which we at the factory can determine. We do not recommend galvanizing for water service when temperatures exceed 160° Fahrenheit. The largest diameter tank that can be galvanized is 72” OD.

“EPOXOLINE”

This superior tank lining has excellent resistance to corrosive hot water. It is a multifunctional epoxy phenolic resin reacted with a special aliphatic amine adduct. The polymer structure is odorless, tasteless, non-toxic, and has excellent resistance to thermal shock. This durable lining conforms to Title 21 CFR 175.300 US Food & Drug Administration and the USDA requirements for coatings in contact with food and drinking water. Prior to sandblasting, all interior welds are ground smooth to eliminate sharp edges and high spots. The vessel interior is then sandblasted to near-white metal per SSPC-SP-10 and lined with two separate coats of epoxy to produce 8-16 mils total dry film thickness. “Epoxoline” has service capabilities for potable water up to 180° F. dry and wet temperature. This lining will not crack or break during proper installation. For chemical applications, we suggest that you contact the factory for specific data and compatibility.

“CEMENTLINE”

Cement lining is another time tested lining for protection against corrosion in steel hot water tanks. Wendland’s cement lining is specially formulated hydro-plastic cement for withstanding corrosive hot water to 212° Fahrenheit. Prior to installation, the interior of the vessel is thoroughly cleaned of rust, mill scale and grease. The interior is then covered with a heavy-duty metal lath, which is secured to the vessel walls at 12” centers. The cement is then troweled throughout the vessel to a thickness of 5/8”. This creates a superior and durable lining which can better withstand handling during shipments along with an outstanding lining for corrosive hot water.


AWWA AND NSF LININGS

Hydropneumatic and other types of water tanks for potable water systems normally require a lining approved by State Health authorities. The American Water Works Association is a national organization, which most states recognize for lining standards of potable water storage tanks. Wendland offers several interior linings meeting the latest revision of AWWA D102 pamphlet for painting steel water storage tanks. We adhere to strict application requirements of this AWWA painting specification. For economical reasons, we recommend inside paint system #1, which is an epoxy system. These include TNEMEC Series 20 Potapox, and others that can be provided upon request. These systems meet EPA requirements and should give many years of trouble free service.

OTHER LININGS

Wendland has a wide variety of other tank linings available. They include asphalt, coal tar, epoxies, and many other chemical resistant coatings that are available for your specific requirements. We strive to keep abreast of innovations in the paint industry and improve and upgrade our current linings along with offering new linings when they are available. We take great care in the selection of linings, as they can add many years of service to your tanks. Contact us for your coating needs or if we can help select a particular lining for your purpose.

INSULATION AND METAL JACKET

Wendland also offers insulation and metal jacketing on all our pressure vessels. Standard insulation is 2” thick to meet ASHRAE specification 90.1-1989. Metal jacket is extra heavy 14-gauge material. The tank is prime painted prior to insulation and jacketing and then the jacket is also prime painted for added protection. Most insulated and jacketed vessels are skidded for shipment.

SPRAY FOAM INSULATION

Wendland uses polyurethane foam, R-16 with weatherproof topcoat. These tanks require protective skidding and special shipping arrangements. Please consult the factory if your specification calls for spray foam insulation.

IMPORTANT WARRANTY INFORMATION

To validate the warranty, Wendland Manufacturing requires that all hot water tanks be installed with dielectric bushings to aid in corrosion prevention. Please read the warranty sections of this catalog for additional information.

8"

VERTICAL WATER STORAGE TANK

" Diameter

DRAIN G

A

EHOT WATEROUTLETSIZE OPTIONAL

4"D

Ove

rall

Len g

th

12"4

WATER INLETSIZE OPTIONAL

F

6"

E

8"C

D

1/2" PRESSUREGAUGE

FC A

(2) LIFTING LOOPS

RECIRCULATIONSIZE OPTIONAL

2

6"

H

3/4" THERMOMETER

1-1/4" TANKSTAT

1

MANWAY

C L

M

3

RELIEF VALVE

M

B

C L

BH

45°

WATER STORAGE TANKS

Our Wendland water storage tanks are utilized with a boiler, solar heating medium or other types of hot water heating systems to store domestic water. When sized properly these tanks are an effective means of storage of hot water for meeting maximum usage requirements along with normal system needs. As peak hot water demand requirements are critical, we suggest using ASHRAE’s latest guide and data book for the sizing of these tanks.

The hot water storage tank drawings shown in this book are for customer convenience and are intended as a guide only. We will custom fabricate each vessel to your requirements. We can fabricate the vessels per A.S.M.E. code with stamp or as a Wendland standard pressure tank either code or non-code.

As hot water can be corrosive, we recommend these tanks be internally lined for extended tank life. For interior linings, Wendland recommends Epoxoline orCementline. Refer to the lining section of this catalog for other available linings. We also require that those tanks used for hot water be installed using dielectric bushings to aid in corrosion prevention.

Wendland Manufacturing can assist you in formulation and writing specifications for your particular hot water storage tank requirements.

GENERAL NOTES: Water Storage Tanks

1) If centerline of vessel is on girth seam, openings will be offset 6”.

2) See Accessory details for alternate supports.

3) Manway is not required on tanks 36” or less unless lined. Inspection couplings will be installed if manway is not required.

4) Vertical legs dimension can be changed as required.

5) See Engineer Specification W-100 for a written specification for this tank.

OVERALL LENGTH

1/2" PRESSUREGAUGE

HORIZONTAL WATER STORAGE TANK

M C


6"

H

MANWAY3

DRAIN

2 5G

L

HOT WATEROUTLETSIZE OPTIONAL

LIFT LUGSA6"

1

RELIEFVALVE

B

DIA

MET

ER

1-1/4"TANKSTAT

E


6"

FGH

F

C L

3/4" THERMOMETER

D

C 6"

E

D

CBA


CHILL WATER/BUFFER TANKS

Our chill water tanks are used in conjunction with the buildings chiller system for additional volume required for operation. The chill water tank drawing in this manual is our standard. We can custom fabricate each vessel to your exact requirements. We offer, at customer option, NPT connections in lieu of flanges, internal baffle plate and insulation and metal jacket. The chill water tank exterior will be power wire brushed and painted with one coat of standard

shop primer. Galvanized tanks are available at customer option. Tanks larger than 36” diameter will require a manway to meet A.S.M.E. code specifications.

CHILL WATER TANK NOTES

1. Chill water tank material stocked is normally for 125 psi. Contact factory if you require different size or design pressure.

2. See Engineering Specification CW-100 for a written specification for this tank.

Ove

rall L

engt

h

6"

8"

OPTIONALNPT Connection

OPTIONAL2" Fiberglass Insulation& 14 Gauge Metal Jacket

6"

VERTICAL CHILL WATER TANK

BafflePlate

Diameter

FC

Lift Lugs

A

F

E

C

D

6"

6"

OPTIONAL3/6" PlateBaffle

B

12"

OPTIONALNPT Connection

E

D

A



" OD


3/4" THERMOMETER

1-1/4" TANKSTAT


C L

8"

45°

VERTICAL WATER HEATER TANK

4"

O. A. L.

F

6"

12"4

DRAIN

H

G

COLD WATER INLETSIZE OPTIONAL

D

E

1/2" PRESSUREGAUGE

C A8"

D E M

(2) LIFTING LOOPS

FC A

J

2

M

MANWAY3

1

TANK HEATINGUNIT

RELIEF VALVEB

H

C L

B

J

OVERALL LENGTH

1/2" PRESSUREGAUGE

F

C 6"

HORIZONTAL WATER HEATER TANK

52



MANWAY3

M

6"H

A6"

DRAING

C L

1

RELIEFVALVE

LIFT LUGS B


GH

1-1/4"TANKSTAT

DIAM

ETER

D

TANK HEATINGUNIT

6"

J

E

3/4" THERMOMETER

D

L

F

J

C

E

CBA

WATER HEATERSWendland’s water heater tanks are used for the storage andheating of water. We can furnish tank-heating units for usewith steam, boiler water, or electricity as the heating source.Due to our wide selection of tank capacities for storage andthe availability of tank heating units, the proper water heatertank can be fabricated for a more economical operation tomeet peak and normal operating demands for special jobrequirements. For proper sizing and selection of your waterheater tank, we suggest using ASHRAE’s latest guide anddata book with the tank heating unit catalog in this manual.

The outline drawings we have provided in this manual arefor customer convenience and are intended as a guide only.We will custom fabricate each vessel to your requirements.We can fabricate the vessels per A.S.M.E. code with stampor as a Wendland standard pressure tank.

As hot water can be corrosive, we recommend these tanksbe internally lined for extended tank life. For interior linings,Wendland recommends Epoxoline or Cementline. Refer tothe lining section of this catalog for other available linings.We also require that these tanks be installed using dielectricbushings to aid in corrosion prevention.

Wendland Manufacturing can assist you in writingspecifications for your particular water heater requirements.

GENERAL NOTES: Hot Water Heater Tanks

1) If centerline of vessel is on girth seam, openings will beoffset 6”.

2) See Accessory details for alternate supports.

3) Manway is not required on tanks 36” or less unlesslined. Inspection couplings will be installed if manway isnot required.


5) See Engineer Specification W-200 for a writtenspecification for this tank.

FIRE PROTECTION TANKS The Wendland fire protection tank is a pressure tank used for private fire protection systems. These tanks are constructed in accordance with the latest ASME code specifications, under Section VIII, Division 1 and meet the specifications as required by the latest edition of National Fire Protection Association pamphlet #22. To determine the capacity for the tank in this system, we suggest you refer to the latest NFPA pamphlet #13, “Standard for the Installation of Sprinkler Systems” In all cases, sizing must meet the requirements of the local or State governing authority having jurisdiction. The outline drawing shown in this manual was specifically designed to meet ASME and NFPA requirements. If the governing authority requires changes, Wendland can fabricate the custom designed vessel to your requirements. In addition to the standard hydrostatic test dictated by the ASME Code, we will test the tank to meet NFPA #22 requirements. NFPA requires the tank to be tested 24 hours at two-thirds capacity at normal working pressure and shall not lose more than one-half pound pressure in this period. We will furnish a signed certificate for the file of the governing authority certifying that the test has been successfully completed. The NFPA requires the tanks be thoroughly cleaned by scraping, wire brushing, wiping, and be painted inside and outside with at least two coats of an approved metal protective

paint. As the interior is subjected to severe corrosion problems due to the standing water, we recommend the interior be painted with a coal tar lining or our standard Epoxoline. Due to shipping, we recommend the exterior be prime painted at the factory and the finish coat is applied at the job site. We can finish out the exterior per your requirements if needed. Sandblasting is available at the factory when required. Refer to the lining section of this catalog for other available linings and further explanation.

Fire Protection Tank Notes 1. See Support section for supports

available. 2. Fire Protection Storage Tanks are

available in several design pressures. 3. See Engineer Specification W-300 for a

written specification for this tank. Dia. OAL “W” Dia. OAL “W” 48 146 30-1/4 84 307 53 48 206 30-1/4 84 331 53 54 149 34 96 144 60-1/2 54 197 34 96 168 60-1/2 54 221 34 96 192 60-1/2 60 174 37-3/4 96 216 60-1/2 60 246 37-3/4 96 240 60-1/2 72 180 45-1/2 96 264 60-1/2 72 240 45-1/2 96 288 60-1/2 72 288 45-1/2 96 312 60-1/2 84 211 53 96 336 60-1/2 84 259 53 96 432 60-1/2

OUTLET - 4" FLANGE MINIMUMSIZE OPTIONAL

OVERALL LENGTH

FIRE PROTECTION TANK E

LIFT LUGS

2" DRAIND

2/3 WATER LEVEL

2"

6"

2" AIR/WATER INLET 6"

C

ED

C L

C

" Dia

met

er

MANWAY

M

A

W

A

B

(2) - 3/4" GAUGEGLASS FITTINGS

B

2/3 WATERLEVEL MARKPLATE

12"

M

6"


C L

45°

180°

RELIEF VALVE

INLET/OUTLET

VERTICAL HYDROPNEUMATIC TANK

" Diameter

D

Ove

rall

Len g

thSIGHTGLASS

12"DRAIN G

6"

H E

F

PRESSUREGAUGE

8"

225°

D

A

E

270°A

HF

(2) LIFTING LOOPS 0°

MANWAY

3 1

12"

M

LEVELCONTROL

C2

C

AIR INLET

6"B

135°

C

C L MB90°

HYDROPNEUMATIC STORAGE TANKS Our Hydropneumatic tanks are primarily used for private and public water systems for potable service. They can also be used in wastewater treatment plant applications. A properly designed and maintained system can give many years of trouble free and economical service. For proper selection and sizing of your potable hydropneumatic system, we suggest you contact your domestic water supply division of your State Health Division as you are required to meet health laws for your particular state.

The hydropneumatic tank outline drawing provided in this manual is for convenience and is intended as a guide only. As there are many types of controls systems, we can fabricate the vessel to meet those requirements. Fabrication of vessels to A.S.M.E. code with stamp or as a Wendland standard pressure tank is available at your option.

As these tanks are generally for potable service, great care must be taken in selection of interior tank linings. We suggest using a lining approved by the American Water Works Association per pamphlet AWWA D-102, latest revision.

Wendland Manufacturing can assist you in formulation and writing specifications for your particular hydropneumatic tank requirements. (See Engineer Specification No. W-400)

GENERAL NOTES: Hydropneumatic Tanks

1) See accessory details for alternate supports.

2) Manway is not required on tanks 36” or less. Inspection couplings will be installed if manway is not required. Manway is required for all lined tanks other than galvanized.



OVERALL LENGTH

1/2" PRESSUREGAUGE

OUTLET

HORIZONTAL HYDROPNEUMATIC TANKDRAIN

6"

G

MANWAY2

M

1

C L

LIFT LUGS

RELIEF

6" A INLETB

DIA

MET

ER

E

6"

F

E

GF

LC

SIGHT GLASSD

C 6"

D

CBA


AIR RECEIVER TANKS

Wendland’s air receivers are utilized with air compressors for storage and improved operation of air systems. The vessel provides storage capacity permitting proper pressure and volume requirements during peak usage when normal compressor output is exceeded. Along with reducing air-entrained moisture and oil which settles during the storage period, it reduces pulsation in the systems due to peak requirements and helps extend the lifetime of the compressor. The drawings for air receivers in this manual are intended as a guide and are for customer convenience. Wendland Manufacturing Corporation can assist you in formulation and writing specifications for your air receiver requirements for higher operating pressures.

AIR RECEIVER TANK NOTES

1) See accessory details for alternate supports. 2) Manway is not required on tanks 36” or less.

Inspection couplings will be installed if manway is not required. Manway will be required for lined tanks other than galvanized. Manway size will be 12” x 16” unless otherwise specified.

3) Vertical legs dimensions can be changed as

required. 4) See Engineer Specification W-500 for a written

specification for this tank.

VERTICAL AIR RECEIVER TANK

F

AM

" Diameter

" OVE

RHEA

DS

12" 31

M

DRAIN

C D

1/4" PRESSUREGAUGE

1" REGULATOR

AIR INLETSIZE OPTIONA

MANWAY2

B

E

AIR OUTLETSIZE OPTIONAL

30°

3/4" FCFor Field Testing

A

(2) LIFTINGLOOPS

3/4" FCFor Field Testing

RELEIF VALVESIZE & QTYOPTIONAL

C

D

C

C E B

OVERALL LENGTH

AIR OUTLETSIZE OPTIONAL

DRAIN

1" REGULATOR

AIR INLETSIZE OPTIONAL

RELIEF VALVESIZE & QTYOPTIONAL

HORIZONTAL AIR RECEIVER TANK

MANWAY2

M

1

1/4" PRESSUREGAUGE

DA C C

" Dia

met

e r

FF

E BEB

ADC


STANDARD STORAGE TANKSDimensions Capacity Openings

OD Shell OAL(1) (ACTUAL "B" "G" ManwayCatalog No. In. In. In. gallons +/- 3) SQ. FT. Rel. VA Drain See Note

WS-24-3 (2) 24 36 51 91 28 1" 1" N/A WS-24-4 (2) 24 48 63 114 31 1" 1" N/A WS-24-5 (2) 24 60 75 137 40 1" 1" N/A WS-24-6 (2) 24 72 87 159 46 1" 1" N/A WS-24-7 (2) 24 84 99 182 53 1" 1" N/A WS-24-8 (2) 24 96 111 205 59 1" 1" N/A WS-30-4 (2) 30 48 66 185 45 1" 1" N/A WS-30-5 (2) 30 60 78 220 53 1" 1" N/A WS-30-6 (2) 30 72 90 256 60 1" 1" N/A WS-30-7 (2) 30 84 102 292 68 1" 1" N/A WS-30-8 (2) 30 96 114 328 75 1" 1" N/A WS-30-9 (2) 30 108 126 364 82 1" 1" N/A WS-36-4NM 36 48 68 271 54 1" 1-1/2" NoneWS-36-5NM 36 60 80 322 63 1" 1-1/2" NoneWS-36-6NM 36 72 92 374 73 1" 1-1/2" NoneWS-36-7NM 36 84 104 426 82 1" 1-1/2" NoneWS-36-8NM 36 96 116 478 92 1" 1-1/2" NoneWS-36-9NM 36 108 128 530 101 1" 1-1/2" NoneWS-36-10NM 36 120 140 581 110 1" 1-1/2" NoneWS-36-4 36 48 68 271 54 1" 1-1/2" Lined OnlyWS-36-5 36 60 80 322 63 1" 1-1/2" Lined OnlyWS-36-6 36 72 92 374 73 1" 1-1/2" Lined OnlyWS-36-7 36 84 104 426 82 1" 1-1/2" Lined OnlyWS-36-8 36 96 116 478 92 1" 1-1/2" Lined OnlyWS-36-9 36 108 128 530 101 1" 1-1/2" Lined OnlyWS-36-10 36 120 140 581 110 1" 1-1/2" Lined OnlyWS-42-4 42 48 70 380 67 1" 1-1/2" AllWS-42-5 42 60 82 451 78 1" 1-1/2" AllWS-42-6 42 72 94 522 89 1" 1-1/2" AllWS-42-7 42 84 106 593 100 1" 1-1/2" AllWS-42-8 42 96 118 663 110 1" 1-1/2" AllWS-42-9 42 108 130 734 121 1" 1-1/2" AllWS-42-10 42 120 142 805 132 1" 1-1/2" AllWS-42-11 42 132 154 875 148 1" 1-1/2" AllWS-42-12 42 144 166 946 154 1" 1-1/2" AllWS-42-13 42 156 178 1017 170 1" 1-1/2" AllWS-48-4 48 48 74 508 80 1-1/2" 2" AllWS-48-5 48 60 86 601 93 1-1/2" 2" AllWS-48-6 48 72 98 693 105 1-1/2" 2" AllWS-48-7 48 84 110 785 118 1-1/2" 2" AllWS-48-8 48 96 122 877 130 1-1/2" 2" AllWS-48-9 48 108 134 969 142 1-1/2" 2" AllWS-48-10 48 120 146 1061 155 1-1/2" 2" AllWS-48-11 48 132 158 1153 167 1-1/2" 2" AllWS-48-12 48 144 170 1245 180 1-1/2" 2" AllWS-48-13 48 156 182 1337 192 1-1/2" 2" AllWS-48-14 48 168 194 1429 205 1-1/2" 2" AllWS-48-15 48 180 206 1521 217 1-1/2" 2" All

(1)Overall length may vary depending on the type of head used and does not include supports (2)Also available as galvanized. Consult factory.NOTE: ALL LINED TANKS HAVE A 12" X 16" MANWAY. ALL UNLINED TANKS 42" OD AND OVER HAVE A 12" X 16" MANWAY


STANDARD STORAGE TANKSDimensions Capacity Openings

OD Shell OAL(1) (ACTUAL "B" "G" ManwayCatalog No. In. In. In. gallons +/- 3) SQ. FT. Relief Drain See Note

WS-54-4 54 48 77 659 94 1-1/2" 2" AllWS-54-5 54 60 89 775 108 1-1/2" 2" AllWS-54-6 54 72 101 892 122 1-1/2" 2" AllWS-54-7 54 84 113 1009 136 1-1/2" 2" AllWS-54-8 54 96 125 1126 150 1-1/2" 2" AllWS-54-9 54 108 137 1243 164 1-1/2" 2" AllWS-54-10 54 120 149 1359 178 1-1/2" 2" AllWS-54-11 54 132 161 1476 192 1-1/2" 2" AllWS-54-12 54 144 173 1593 206 1-1/2" 2" AllWS-54-13 54 156 185 1710 220 1-1/2" 2" AllWS-54-14 54 168 197 1827 234 1-1/2" 2" AllWS-54-15 54 180 209 1943 248 1-1/2" 2" AllWS-54-16 54 192 221 2060 262 1-1/2" 2" AllWS-54-17 54 204 233 2177 276 1-1/2" 2" AllWS-60-4 60 48 78 831 114 1-1/2" 2" AllWS-60-5 60 60 90 975 130 1-1/2" 2" AllWS-60-6 60 72 102 1119 146 1-1/2" 2" AllWS-60-7 60 84 114 1263 162 1-1/2" 2" AllWS-60-8 60 96 126 1407 177 1-1/2" 2" AllWS-60-9 60 108 138 1551 193 1-1/2" 2" AllWS-60-10 60 120 150 1694 208 1-1/2" 2" AllWS-60-11 60 132 162 1838 224 1-1/2" 2" AllWS-60-12 60 144 174 1982 240 1-1/2" 2" AllWS-60-13 60 156 186 2126 256 1-1/2" 2" AllWS-60-14 60 168 198 2270 272 1-1/2" 2" AllWS-60-15 60 180 210 2414 287 1-1/2" 2" AllWS-60-16 60 192 222 2558 302 1-1/2" 2" AllWS-60-17 60 204 234 2701 318 1-1/2" 2" AllWS-60-18 60 216 246 2845 334 1-1/2" 2" AllWS-60-19 60 228 258 2989 350 1-1/2" 2" AllWS-60-20 60 240 270 3133 366 1-1/2" 2" AllWS-60-21 60 252 282 3277 381 1-1/2" 2" AllWS-66-4 66 48 82 1033 135 1-1/2" 2" AllWS-66-5 66 60 94 1208 152 1-1/2" 2" AllWS-66-6 66 72 106 1382 169 1-1/2" 2" AllWS-66-7 66 84 118 1557 186 1-1/2" 2" AllWS-66-8 66 96 130 1731 203 1-1/2" 2" AllWS-66-9 66 108 142 1905 221 1-1/2" 2" AllWS-66-10 66 120 154 2080 237 1-1/2" 2" AllWS-66-11 66 132 166 2254 254 1-1/2" 2" AllWS-66-12 66 144 178 2428 271 1-1/2" 2" AllWS-66-13 66 156 190 2603 289 1-1/2" 2" AllWS-66-14 66 168 202 2777 306 1-1/2" 2" AllWS-66-15 66 180 214 2952 323 1-1/2" 2" AllWS-66-16 66 192 226 3126 340 1-1/2" 2" AllWS-66-17 66 204 238 3300 357 1-1/2" 2" AllWS-66-18 66 216 250 3475 374 1-1/2" 2" AllWS-66-19 66 228 262 3649 391 1-1/2" 2" AllWS-66-20 66 240 274 3824 409 1-1/2" 2" AllWS-66-21 66 252 286 3998 426 1-1/2" 2" All

(1)Overall length may vary depending on the type of head used and does not include supports (2)Also available as galvanized. Consult factory.

NOTE: ALL LINED TANKS HAVE A 12" X 16" MANWAY. ALL UNLINED TANKS 42" OD AND OVER HAVE A 12" X 16" MANWAY


STANDARD STORAGE TANKSDimensions Capacity

OD Shell OAL (ACTUAL "B" "G" ManwayCatalog No. In. In. In. gallons +/- 3) SQ. FT. Rel. VA Drain See Note

WS-72-5 72 60 96 1469 172 1-1/2" 2" AllWS-72-6 72 72 108 1677 191 1-1/2" 2" AllWS-72-7 72 84 120 1885 210 1-1/2" 2" AllWS-72-8 72 96 132 2093 229 1-1/2" 2" AllWS-72-9 72 108 144 2301 248 1-1/2" 2" AllWS-72-10 72 120 156 2509 267 1-1/2" 2" AllWS-72-11 72 132 168 2717 286 1-1/2" 2" AllWS-72-12 72 144 180 2924 304 1-1/2" 2" AllWS-72-13 72 156 192 3132 323 1-1/2" 2" AllWS-72-14 72 168 204 3340 342 1-1/2" 2" AllWS-72-15 72 180 216 3548 360 1-1/2" 2" AllWS-72-16 72 192 228 3756 379 1-1/2" 2" AllWS-72-17 72 204 240 3964 398 1-1/2" 2" AllWS-72-18 72 216 252 4172 417 1-1/2" 2" AllWS-72-19 72 228 264 4380 438 1-1/2" 2" AllWS-72-20 72 240 276 4587 457 1-1/2" 2" AllWS-72-22 72 264 300 5003 495 1-1/2" 2" AllWS-72-24 72 288 336 5211 514 1-1/2" 2" AllWS-84-5 84 60 103 2082 208 1-1/2" 2" AllWS-84-6 84 72 115 2366 230 1-1/2" 2" AllWS-84-7 84 84 127 2649 252 1-1/2" 2" AllWS-84-8 84 96 139 2933 274 1-1/2" 2" AllWS-84-10 84 120 163 3500 318 1-1/2" 2" AllWS-84-12 84 144 187 4068 362 1-1/2" 2" AllWS-84-14 84 168 211 4635 406 1-1/2" 2" AllWS-84-16 84 192 235 5202 450 1-1/2" 2" AllWS-84-18 84 216 259 5769 494 1-1/2" 2" AllWS-84-20 84 240 283 6337 538 1-1/2" 2" AllWS-84-22 84 264 307 6904 582 1-1/2" 2" AllWS-84-24 84 288 331 7471 626 1-1/2" 2" AllWS-96-5 96 60 108 2833 250 1-1/2" 2" AllWS-96-6 96 72 120 3203 275 1-1/2" 2" AllWS-96-7 96 84 132 3573 300 1-1/2" 2" AllWS-96-8 96 96 144 3944 325 1-1/2" 2" AllWS-96-10 96 120 168 4684 375 1-1/2" 2" AllWS-96-11 96 132 180 5054 400 1-1/2" 2" AllWS-96-12 96 144 192 5425 425 1-1/2" 2" AllWS-96-14 96 168 216 6165 475 1-1/2" 2" AllWS-96-16 96 192 240 6905 525 1-1/2" 2" AllWS-96-18 96 216 264 7646 575 1-1/2" 2" AllWS-96-20 96 240 288 8386 625 1-1/2" 2" AllWS-96-22 96 264 312 9127 675 1-1/2" 2" AllWS-96-24 96 288 336 9,867 725 1-1/2" 2" AllWS-96-32 96 384 432 12,829 925 1-1/2" 2" All

(1)Overall length may vary depending on the type of head used and does not include support(2)Also available as galvanized. Consult factory.NOTE: ALL LINED TANKS HAVE A 12" X 16" MANWAY. ALL UNLINED TANKS 42" OD AND OVER HAVE A 12" X 16" MANWAY

Openings


FLASH TANKS

Our flash tanks are intended for flashing of high-pressure condensate into steam. It can also be used for cooling low-pressure steam prior to return to boiler, condensate receiver, or for discharge into sewer. The flash tank drawings in this manual are our standards. We can custom fabricate each vessel to your exact requirements. We offer, at customer option, an inlet spray pipe. The area of the drilled holes in the spray pipe will be equal to the cross sectional area of the pipe. The Flash tank exterior will be power wire brushed and painted with one coat of standard shop primer. Galvanized tanks are available at customer option. Tanks larger than 36”

diameter will require a manway to meet A.S.M.E. code specifications. Wendland Manufacturing Corporation will make every effort to assist you in formulation and writing specifications for your flash tank requirements.

FLASH TANK NOTES

1. Flash tank material stocked is normally for 150 psi. Contact factory if you require different size or design pressure.

2. Vertical flash tanks are also available. 3. See Engineering Specification W-600 for a

written specification for this tank.

FLASH TANK

SPRAYPIPE

INSPECTIONOPENINGS

Overall Length

OUTLETSIZEOPTIONAL

B

E

VENT5" D

INLETSIZEOPTIONAL

" Dia

met

e r

DRAINC

A

5"E


FLASH TANKS

MODEL

SIZE

CAPACITY GALLONS

“A” INLET

“B” OUTLET

“C” DRAIN

“D” VENT

“E” INSP.

PIPE SIZE X LENGTH W/HOLE QTY X HOLE DIA.

FT-15 12” X 30” 15 1” 2” 1” 2” N/A 1” X 18” LG. W/(18) 1/4”

FT-24 12” X 50” 24 1-1/4” 2” 1” 2” N/A 1-1/4” X 30” LG. W/(30) 1/4”

FT-30 14” X 50” 30 1-1/4” 2” 1” 2” 2-1/2” 1-1/2” x 30” LG. W/(30) 1/4”

FT-40 16” X 50” 40 1-1/2” 2” 1” 2” 1-1/2” 1-1/2” X 42” LG. W/(42) 1/4”

FT-60 16” X 70” 60 1-1/2” 2” 1” 2” 1-1/2” 1-1/2” X 42” LG. W/(42) 1/4”

FT-80 20” X 60” 80 1-1/2” 2” 1-1/2” 2” 2” 1-1/2” X 42” LG. W/(42) 1/4”

FT-100 20” X 72” 100 2” 2” 1-1/2” 2” 2” 2” X 45” LG. W/(45) 5/16”

FT-120 24” X 61” 120 2” 2” 1-1/2” 2” 2” 2” X 45” LG. W/(45) 5/16”

FT-140 24” X 73” 140 2” 2” 1-1/2” 2” 2” 2” X 45” LG. W/(45) 5/16”

FT-175 30” X 65” 175 3” 2” 2” 2” 2” 3” X 60” LG. W/(66) 3/8”

FT-250 30” X 89” 250 3” 2” 2” 2” 2” 3” X 60” LG. W/(66) 3/8”

LENGTH (INCHES) AS REQUIRED

AREA OF DRILLED HOLES TOEQUAL OR EXCEED CROSSSECTIONAL AREA OF PIPE3 HOLES PER ROW

SIZE AS REQ'D

PIPE SIZEAS REQ'D

90°90°

CAP

OPTIONAL SPRAY PIPE

MNPT

FLASH TANK SIZING CHART

Flash Tank Capacity (Gallons)

Condensate GPM

15 0 to 15

24 16 to 22

30 23 to 30

40 31 to 40

60 41 to 60

80 61 to 80

100 81 to 100

120 101 to 120

140 101 to 150

175 151 to 200

250 201 to 265


EXPANSION TANKS

Wendland’s standard expansion tank allows for the expansion and contraction of the hydronic system and provides for proper pressurization under different operating conditions. We recommend using ASHRAE’s latest guide and data book for determining your tank volume requirements. The catalog “C” model expansion tank drawing is our standard tank. Please consult the factory for expansion tanks built to your specific specifications if changes are required. Our expansion tanks are designed for 150 psi A.S.M.E. code with stamp and are tested at 225 psi. The “C” model tanks are thoroughly power wire brushed and prime painted prior to shipment. The “CG” model is our standard hot dipped galvanized expansion tank.

WENDLAND MANUFACTURING CORP 10-01-2004 17

A.S.M.E. CODE EXPANSION TANK NOTES 1) Tanks are designed, constructed, and

stamped in accordance with Section VIII, Division 1 for the A.S.M.E. Code for unfired pressure vessels.

2) Tank exterior to be prime painted with one coat of standard shop primer.

3) Inspection openings are provided on all Expansion tanks as required by A.S.M.E. code.


A.S.M.E. CODE EXPANSION TANK

DRAIN

OVERALL LENGTH

O D E

CD

C L

BB

(2) 1/2" GAUGEGLASS FITTINGS

AA

E

INSPECTIONOPENINGS

E

INLET1/4 TANKLENGTH

C D

C L

2

3

OVERHEAD EXPANSION TANK HANGING BRACKET NOTES HANGING BRACKETS 1. Maximum total weight capacity is 4000

A

B

BOLT HOLE CENTERS

1

C

D

Tank Dia.

Dim. “A”

Dim. “B”

Dim. “C”

Hole Size “D”

12” 18” 24” 2” 1/2” 14” 20” 26” 2” 1/2” 16” 22” 28” 2” 1/2” 18” 24” 30” 2” 1/2” 20” 26” 32” 3” 3/4” 24’ 30” 36” 3” 3/4” 30” 36” 42” 3” 3/4” 36” 42” 48” 3” 3/4”

WENDLAND MANUFACTURING CORP 10-01-2004 18

A.S.M.E. CODE EXPANSION - COMPRESSION TANKS (150 PSI)

MODEL

SIZE

CAPACITY GALLONS

DIMENSION “E”

“C” DRAIN

“D” INLET

C-15 12” X 30” 15 7” 3/4” 3/4”

C-24 12” X 50” 24 7” 3/4” 3/4”

C-30 14” X 50” 30 8” 3/4” 3/4”

C-40 16” X 50” 40 9” 3/4” 3/4”

C-60 16” X 70” 60 9” 3/4” 3/4”

C-80 20” X 60” 80 12” 3/4” 3/4”

C-100 20” X 72” 100 12” 3/4” 3/4”

C-120 24” X 61” 120 14” 3/4” 3/4”

C-140 24” X 73” 140 14” 3/4” 3/4”

C-175 30” X 65” 175 17” 1” 1”

C-250 30” X 89” 250 17” 1” 1”


BLOW DOWN TANKSThe Wendland blow-down tanks are fabricatedwith 3/8” thick heads and shell and are inspectedand stamped in accordance with the latest ASMEcode specifications, under Section VIII, Division 1for 150 psi design pressure at 300° F. They arealso registered with the National Board of Boilerand Pressure Vessel Inspectors.

Each tank includes an internal wear plate, an inletconnection, an outlet connection with internal elland pipe, a vent connection, a cold water inletconnection, and other connections as shown onour standard drawing.

Each tank also includes a 4” X 6” Handhole or a12” X 16” Manway depending on the size of thetank.If the governing authority requires changes,Wendland can fabricate the custom designedvessel to your requirements.

Tank exteriors are painted with one coat of ourstandard shop primer.

Vertical Blow Down Tank Notes

1. See Support section for supports available.2. Vertical leg dimensions can be changed as

required.3. See Engineer Specification W-800 for a

written specification for this tank.SIPHONBREAKER

SCHEDULE40 PIPE

VERTICAL BLOW DOWN TANK

DRAIN

8"

(2) LIFTING LOOPS

" Diameter

D

G

8"SH

ELL

LENG

TH

12"2

6"

Cold WaterInlet

6"J

Sight Glass

A

H

Inlet

A

PressureGauge

C

H C GJ

6" WIDEWEAR PLATE3/8" THICK

F

6"

1

C 4"L

Thermomete5"

H

B

Outlet

Vent

F

M

BC L

M

E

45°

180° WEARPLATE


Horizontal Blow Down Tank Notes

1. See Support Section for supports available2. See Engineer Specification W-800 for a written specification for this tank.

Model No.& Size

BoilerHP Gallons Inlet Vent Outlet Drain Inspection

BD243V 5 to 50 91 1” 2-1/2” 1-1/2” 1-1/2” 4”X6” HH24” X 36”

BD305V 51 to 100 220 1” 2-1/2” 1-1/2” 1-1/2” 4”X6” HH30” X 60”

BD365V 101 to 130 322 1-1/4” 3” 2” 1-1/2” 4”X6” HH36” X 60”

BD367V 101 to 170 426 1-1/4” 3” 2” 1-1/2” 4”X6” HH36” X 84”

BD425V 101 to 175 448 1-1/2” 4” 2-1/2" 2" 12”X16” MW42” X 60”

BD485V 151 to 200 601 2” 6” 4” 2” 12”X16” MW48” X 60”

BD604V 201 & Up 837 2-1/2” 8” 6” 2” 12”X16” MW60” X 48”

OVERALL LENGTH

Relief

HORIZONTAL BLOW DOWN TANK

SiphonBreaker

Vent

Outlet

6"

B

C

3/8" ThickWear Plate

F1

DRAIN

E E

F

3/4" Cold WaterInlet

" Diam

eter

Inlet

A

M

InspectionManway

F

D

A

C

M


AIR SEPARATOR TANKS

Our air separator tanks are intended forseparation of air and water.

The air separator tank drawings in this manualare our standards. We can custom fabricateeach vessel to your exact requirements.

Air separator tank exterior will be power wirebrushed and painted with one coat of standardshop primer. Tanks larger than 36” diameterwill require a manway to meet A.S.M.E. codespecifications.

AIR SEPARATOR TANK NOTES

1. All separators with 3” in/out and below donot have skirts.

2. Larger sizes of in line air separators areavailable upon request.

3. Hanger lugs can be supplied in lieu of skirtif requested.

4. See Engineer Specification W-900 for awritten specification for this tank.

AIR SEPARATOR TANK (WITHOUT STRAINER)

"C"

1-1/2" NPT

" OD

OAL

"A"

OUTLET

6"SKIRT

1" NPT

C L

C L

1/2" NPT

C L

"B"

INLET

MODEL IN/OUT DIA. OAL A B C WT. NOZZ. GPM

WASO-2C 2" 12" 30" 9" 12" 13-3/8" 52# 56WASO-2.5C 2-1/2" 12" 30" 9" 12" 15-5/8" 53# 90WASO-3C 3" 12" 30" 9" 12" 16-1/4" 55# 170


AIR SEPARATOR TANKS

" OD

"C"

1-1/2" NPT

If IN/OUT1" NPT (2" THRU 2" NPT (8" & ABO

OAL

OUTLET

"A"

6"

AIR SEPARATOR TANK (WITHOUT STRAINER)

SKIRT

C L

C L

1/2" NPT

C L

"B"

INLET

" OD

"C"

1-1/2" NPT

STRAINER

If IN/OUT1" NPT (2" THRU 6")2" NPT (8" & ABOVE)

OAL

OUTLET

"A"

6"

AIR SEPARATOR TANK (WITH T304 STAINLESS STEEL STRAINER)

SKIRT

C L

1/2" NPT

C L

C L

"B"

INLET

MODEL IN/OUT DIA. OAL A B C WT. NOZZ. GPMWASO-30 3" 12" 30" 9" 12" 22" 75# 170WASO-40 4" 16" 33" 9-1/2" 14" 26" 53# 300WASO-50 5" 20" 42" 12" 18" 30" 195# 500WASO-60 6" 24" 42" 12" 18" 34" 210# 700WASO-80 8" 30" 53" 15-1/2" 22" 40" 440# 1400

WASO-100 10" 36" 64" 16" 32" 46" 635# 2100WASO-120 12" 42" 67" 18-1/2" 30" 54" 1000# 3000

;601 West 11th P.O. Box 808

San Angelo, TX 76902 Phone: (325) 655-6778

Fax: (325) 655-0325 www.wendlandmfg.com

ENGINEERING

SPECIFICATIONS


ENGINEERING SPECIFICATION NO. W-100

WATER STORAGE TANKS

Furnish and install ______(quantity) ________________ (vertical or horizontal) storage tank(s),Wendland Model Number ____________(Consult chart). Tank(s) to be ______” diameter by_________” (OAL or Shell) with a capacity of _____________ gallons.

Provide supports (legs) (skirt) (saddles) to elevate the tank ______” high. Tank to be providedwith manway or inspection openings and connections the size and type as shown on the plans ordrawings. Provide lifting lugs for handling.

The tank shall be:1. Electrically welded to produce smooth and uniform welds with no undercut, 2. ASME, Section VIII, Division 1 inspected and stamped for _______ psig design pressure,3. Registered with the National Board if required,4. Hydrostatically tested at one and one-half times the design pressure.

The engineer shall be provided with an ASME U-1(a) form, signed, and dated by an authorizedinspector.

The exterior of the tank shall be wire brush cleaned per SSPC-SP-3 and painted with one coat ofWendland Standard Primer (can be changed to fit your application). The interior shall be_________________(cleaned per SSPC-SP-3)/(Commercial sandblasted per SSPC-SP-6)/ (Nearwhite sandblasted per SSPC-SP-10)/(White metal sandblast per SSPC-SP-5) and lined perSpecification Number ________________.

ENGINEERING SPECIFICATION NO. CW-100

CHILL WATER/BUFFER TANK


1.01 SCOPE OF WORK

This specification shall govern the furnishing of all materials, labor and equipment to fabricate and deliver a chill water/buffer tank the size and capacity as shown on the plans. The tank shall be designed, constructed, and stamped in accordance with the latest edition of the ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 for 125 psi working pressure at 200°F.

1.02 CHILL WATER/BUFFER TANK

The tank manufacturer is to supply all and any items welded to the tank. Any items or components screwed or bolted to the tank are to be supplied by the vessel installer. The manufacturer shall furnish to the ENGINEER six copies of SHOP DRAWINGS that clearly confirm that the tank will be fabricated in accordance with the code. Prior to delivery, the Manufacturer shall furnish to the ENGINEER two copies of Form U-1/U-1A, Manufacturer’s Data Report for Pressure Vessels.

1.03 MANUFACTURER’S The tank shall be a Wendland Manufacturing Corp. Model No. CW-Model ________

or approved equal. 1.04 CONSTRUCTION

A. The tank shall have appurtenances as shown on the Plans and specified herein. These connections and appurtenances shall include but not be limited to the following:

i) An ASME nameplate must be permanently attached to the tank. ii) An access manhole with cover and gasket shall be installed in

accordance with A.S.M.E. Code requirements and manufacturer’s standard practice when required.

iii) The tank will be constructed of carbon steel and of vertical design with a base skirt.

iv) The tank exterior shall be primer painted. v) Set of lifting lugs. vi) All flanges shall be 150# standard type ANSI B16.5, raised face type,

forged of Specification SA-105 steel. vii) All screwed couplings shall be 3000# half or full couplings of forged

carbon steel meeting Specification SA-105. viii) If required, the tank manufacturer shall utilize spot radiography on the

Head to Shell girth weld and spot radiography on the Shell to Shell girth welds all fully meeting the afore stated codes.

ENGINEERING SPECIFICATION NO. CW-100

CHILL WATER/BUFFER TANK


1.05 OPTIONAL REQUIREMENTS

A. The tank can be epoxy lined. Tanks lined with epoxy lining shall be equipped with the number and size of magnesium anode rods sufficient to provide adequate protection for the tank lining.

B. The exterior of the tank can be covered with 2” fiberglass insulation and 14

gauge metal jacket.

C. The tank can be furnished with non-ferrous tank connections.

D. The tank can be furnished with internal baffle(s).



HOT WATER HEATERS

Furnish and install ______(quantity) ________________ (vertical or horizontal) water heatertank(s), Wendland Model Number ____________(Consult chart). Tank(s) to be ______”diameter by _________” (OAL or Shell) with a capacity of _____________ gallons.


The heating coil shall be Wendland Model Number _______________(Consult chart fornumber) sized to heat __________ gallons per hour from _____°F. to ______°F. with steam inthe tubes at _______psig (or boiler water at ______°(EWT) and _____°(LWT).) The coiltubesheet shall be _______________(steel or naval/bronze). The heating coil shall have aminimum of _______ sq. ft. of heating surface and shall be constructed so that the entire coil canbe removed from the tank for cleaning and inspection.



The exterior of the tank shall be wire brush cleaned per SSPC-SP-3 and painted with one coat ofWendland Standard Primer (can be changed to fit your application). The interior shall be_________________(cleaned per SSPC-SP-3) (Commercial sandblasted per SSPC-SP-6) (Nearwhite sandblasted per SSPC-SP-10) (White metal sandblast per SSPC-SP-5) and lined perSpecification Number ________________.



FIRE PROTECTION TANKS

Furnish and install ______(quantity) horizontal Fire Protection tank(s), Wendland ModelNumber ____________(consult chart). Tank(s) to be ______” diameter by _________”(OAL or Shell) with a capacity of _____________ gallons.

Provide two (2) Style II saddles to elevate the tank ______” high. Tank to be provided withmanway and connections the size and type as shown on the plans or drawings. Provide liftinglugs for handling.


The engineer shall be provided with an ASME U-1(a) form, signed, and dated by anauthorized inspector.

The exterior of the tank shall be wire brush cleaned per SSPC-SP-3 and painted with one coatof Wendland Standard Primer (can be changed to fit your application). The interior shall be_________________(cleaned per SSPC-SP-3) (Commercial sandblasted per SSPC-SP-6)(Near white sandblasted per SSPC-SP-10) (White metal sandblast per SSPC-SP-5) and linedper Specification Number ________________.


HYDROPNEUMATIC STORAGE TANK


PART 1 - GENERAL

1.01 SCOPE OF WORK

This specification shall govern the furnishing of all materials, labor and equipment tofabricate and deliver a hydropneumatic pressure tank the size and capacity as shown onthe plans. The tank shall be designed, constructed, and stamped in accordance with thelatest edition of the ASME Boiler and Pressure Vessel Code, Section VIII, Division 1.Tank manufacturer shall have been in the ASME Vessel manufacturing business for aminimum of five (5) years.

PART 2 - PRODUCTS

2.01 HYDROPNEUMATIC TANK

The tank manufacturer is to supply all and any items welded to the tank. Any items orcomponents screwed or bolted to the tank are to be supplied by the vessel installer. Themanufacturer shall furnish to the ENGINEER six copies of SHOP DRAWINGS thatclearly confirm that the tank will be fabricated in accordance with the code. Prior todelivery, the Manufacturer shall furnish to the ENGINEER two copies of Form U-1/U-1A, Manufacturer’s Data Report for Pressure Vessels.

2.02 MANUFACTURER’SThe tank shall be a Wendland Manufacturing Corp. Model No. HP-Model ________ orapproved equal.

2.03 ACCESSORIES

A. The tank shall have appurtenances as shown on the Plans and specified herein.These connections and appurtenances shall include but not be limited to thefollowing:

i) An ASME nameplate must be permanently attached to the tank. ii) An access manhole with cover and gasket shall be provided the size and

location as shown on the plans.iii) The tank will be provided with a drain the size and location as shown on

the plans.iv) The tank shall be fitted with inlet/outlet connections the size and location

as shown on the plans.v) Threaded nozzles shall be 3,000 pound for sight glass assembly, probes,

air supply, and pressure relief valves.vi) Set of lifting lugs.vii) Sight glass and pressure gauge as specified elsewhere in these

specifications.




viii) Steel saddles shall29vided with the tank and installed on foundationsas shown on the plans.

B. All flanges shall be 150# standard type ANSI B16.5, raised face type, forged of

Specification SA-105 steel. C. All screwed couplings shall be 3000# half or full couplings of forged carbon steel

meeting Specification SA-105. D. Do not provide coupling at center of heads. Weld fabrication holes in each head

up as per the Code and grind flush inside and out. E. If required, the tank manufacturer shall utilize spot radiography on the Head to

Shell girth weld and spot radiography on the Shell to Shell girth welds all fullymeeting the afore stated codes.

F. The tank manufacturer shall calculate thickness of the steel to withstand the

highest expected working pressure with a safety factor on both Heads and Shell asrequired by the most current edition of the ASME Code.

G. The tank manufacturer shall calculate the Shell thickness so as not to have

internal or external stiffener rings.

PART 3 - PAINTING AND PROTECTIVE COATING

3.01 PAINT

A. The tank shall be prepared, blasted, cleaned, primed, and finish coated on theoutside and inside.

B. The inside finish shall be to the “Standard Specifications for Painting and

Repainting Steel Tanks” of the AWWA, D-102, latest edition, and revision, InsideSystem #1. The coating system shall be a two- (2) coat system with a total dryfilm thickness of 8-10 mils.

C. The outside finish coating system shall consist of two (2) coats of Hi-build epoxy

and one (1) coat of Urethane enamel. The total dry film thickness shall be 6-8mils. Owner shall approve color.

D. All protective coatings applied to this vessel shall conform to ANSI/NSF

Standards for potable water service.




PART 4 - SUBMITTALS

I. The Contractor shall furnish for submittal six (6) sets of shop drawings depicting thefollowing prior to fabrication: A. Design and Construction Notes B. Material and Inspection Notes C. Schedule of Openings D. Weld Attachment Details E. Protective Coating System F. Design Calculations

Fabrication may commence after approval of shop drawings.



AIR RECEIVER TANKS

Furnish and install ______(quantity) ________________ (vertical or horizontal) air receivertank(s), Wendland Model Number ____________(consult chart). Tank(s) to be ______”diameter by _________” (OAL or Shell) with a capacity of _____________ gallons.




The exterior of the tank shall be wire brush cleaned per SSPC-SP-3 and painted with one coat ofWendland Standard Primer (can be changed to fit your application). The interior shall be_________________(cleaned per SSPC-SP-3) (Commercial sandblasted per SSPC-SP-6) (Nearwhite sandblasted per SSPC-SP-10) (White metal sandblast per SSPC-SP-5) and lined perSpecification Number ________________.



FLASH TANKS

Furnish and install ______(quantity) vertical or horizontal flash tank(s), Wendland ModelNumber ____________(consult chart). Tank(s) to be ______” diameter by _________” (OALor Shell) with a capacity of _____________ gallons.

Provide supports to elevate the tank _____” high. Include ______” inlet connection with internalspray pipe perforated with holes equal to the cross sectional area of the pipe. Tank to beprovided with inspection openings and standard connections for the outlet, drain, and vent, thesize and type as shown on the plans or drawings.

The tank shall be:1. Electrically welded to produce smooth and uniform welds with no undercut, 2. ASME, Section VIII, Division 1 inspected and stamped for 150 psig design pressure at

_____° design temperature.3. Registered with the National Board if required,4. Hydrostatically tested at one and one-half times the design pressure.


The exterior of the tank shall be wire brush cleaned per SSPC-SP-3 and painted with one coat ofWendland Standard Primer.



EXPANSION TANKS

Furnish and install ______(quantity) horizontal expansion tank(s), Wendland Model Number____________(consult chart). Tank(s) to be ______” diameter by _________” (OAL or Shell)with a capacity of _____________ gallons.

(OPTION: Provide two (2) overhead hanging brackets) Tank to be provided with inspectionopenings and standard connections for the inlet, drain, and gauge glass, the size and type asshown on the plans or drawings.

The tank shall be:1. Electrically welded to produce smooth and uniform welds with no undercut, 2. ASME, Section VIII, Division 1 inspected and stamped for 150 psig design pressure,3. Registered with the National Board if required,4. Hydrostatically tested at one and one-half times the design pressure.


Tank(s) shall be ____________(painted or galvanized). If painted, the exterior of the tank shallbe wire brush cleaned per SSPC-SP-3 and painted with one coat of Wendland Standard Primer.If galvanized, both interior and exterior will be hot dipped galvanized.



BLOW DOWN TANKS

Furnish and install ______(quantity) ________________ (vertical or horizontal) blow-downtank(s), Wendland Model Number ____________(consult chart). Tank(s) to be ______”diameter by _________” (OAL or Shell) with a capacity of _____________ gallons.

Provide supports (legs) (skirt) (saddles) to elevate the tank ______” high. Tank to be providedwith inspection openings (4”x6” handhole or 12”x16” manway), inlet connection ____” (malethreaded pipe or flanged), vent connection _____”(female threaded coupling or flanged), outletconnection _____” (Female threaded coupling or flanged), and other threaded couplings fordrain, thermometer, cold water inlet, pressure gauge, and gauge glass, the size and type as shownon the plans or drawings. Include also an internal carbon steel 3/8” thick wear plate. Tank headsand shell to be minimum 3/8” thick plate to allow for internal corrosion. Provide lifting lugs forhandling.






AIR SEPARATION TANKS

Furnish and install ______(quantity) ________________ vertical air separator tank(s), WendlandModel Number ____________(consult chart). Tank(s) to be ______” diameter by _________”long with a capacity of _____________ gallons.

Provide 6” high skirt. The separator shall be provided _______(with or without) strainer. Tankto be provided with manway or inspection openings and connections the size and type as shownon the plans or drawings. Provide lifting lugs for handling.







SUPPORT ACCESSORIES


SUPPORT ACCESSORIES

We offer a complete line of tank accessoriesand steel supports. The dimensional outlinedrawings show our standard tank supports. Wecan furnish supports to your specifications, butwe recommend standard supports as they aremore economical.

The different kinds of standard tank supportsavailable for vertical tanks are: skirt, angle legsupports, and heavy-duty wide flange beamsupports. Supports for horizontal tanks are:overhead expansion tank hanging brackets,base legs, and saddle supports. All supportsare thoroughly cleaned and painted to matchtank exteriors unless otherwise specified.

Please contact the factory if we can be of anyassistance for special supports or accessories.

SKIRT

TankDia.

Dim.“A”

24” 20”30” 24”36” 30”42” 36”48” 36”54” 42”60” 48”66” 54”72” 60”84” 72”96” 84”

SKIRT

2

*

A

STYLE II - 12"STYLE I - 6"*

3

ANGLE CLIPS ATCUSTOMER OPTION

TANK DIAMETER

1

45.000°

SKIRT NOTES:

1) Mounting holes are not factory drilled, as they are left forfield drilling to suit actual anchor bolt measurements.

2) There are 4 standard skirt access openings. For changes

to the standard, consult factory for pricing. 3) A ring base plate is available as an option.


ANGLE LEG SUPPORTSTankDia.

No. ofLegs

AngleLegs

BasePlate

12” 3 2” x 2” x 1/4” 4” x 4” x 5/16”14” 3 2” x 2” x 1/4” 4” x 4” x 5/16”16” 3 2” x 2” x 1/4” 4” x 4” x 5/16”18” 3 2” x 2” x 1/4” 4” x 4” x 5/16”20” 3 2” x 2” x 1/4” 4” x 4” x 5/16”24” 4 2” x 2” x 1/4” 4” x 4” x 5/16”30” 4 2-1/2” x 2-1/2” x 1/4” 5” x 5” x 3/8”36” 4 2-1/2” x 2-1/2” x 1/4” 5” x 5” x 3/8”42” 4 3” x 3” x 3/8” 5” x 5” x 3/8”48” 4 3” x 3” x 3/8” 5” x 5” x 3/8”54” 4 3” x 3” x 3/8” 5” x 5” x 3/8”60” 4 4” x 4” x 1/2” 6” x 6” x 1/2”66” 4 4” x 4” x 1/2” 6” x 6” x 1/2”72” 4 4” x 4” x 1/2” 6” x 6” x 1/2”84” 4 6” x 6” x 1/2” 8” x 8” x 1/2”96” 4 6” x 6” x 1/2” 8” x 8” x 1/2”

ANGLE LEG SUPPORTS

SECTION A-A

A

1

3

A 12"2

TANK DIAMETER


ANGLE LEG AND HEAVY DUTYWFI BEAM SUPPORT NOTES

1) Mounting holes are not factory drilled, as they are left for field drilling to suit anchor boltmeasurements.

2) Vertical leg dimensions can be changed as required. 3) Legs will straddle natural centerlines unless otherwise required.

HEAVY DUTY WFIBEAM SUPPORTS

Tank Dia.

No. ofLegs

Leg Size

Base Plate

72” 4 6” WF15 3/4” x 10” x 10”84” 4 6” WF15 3/4” x 10” x 10”96” 4 8” WF31 3/4” x 12” x 12”

SUPPORT PADPLATE

WIDE FLANGE "I" BEAMLEGS

BASE PLATE

1

3

12"

2

HEAVY DUTY WFI BEAM SUPPORTS


SADDLE SUPPORTSFOR HORIZONTAL VESSELS

TYPE I SADDLE SUPPORT

Tank Dia. Dim. “A” Dim. “B”

12” 10” 4”14” 12” 4”16” 14” 4”18” 16” 4”20” 17-1/2” 4”24” 21” 4”30” 26” 4”36” 30” 4”42” 33-1/2” 4”48” 44” 6”54” 49” 6”

TYPE II SADDLE SUPPORT

Tank Dia. Dim. “A” Dim. “B”

36” 30” 4”42” 33-1/2” 4”48” 44” 6”54” 49” 6”60” 54” 8”66” 60” 8”72” 64” 8”84” 76” 8”96” 86” 8”

SADDLE SUPPORT NOTES:

1) Mounting holes are not factory drilled, as they are left forfield drilling to suit actual anchor bolt measurements.

2) The Type II saddle supports for 84” diameter and greaterwill be fabricated with full web plate for added strength.

3) Pipe leg bosses are available as an option.


A

TYPE I SADDLE SUPPORT

A

TYPE II SADDLE SUPPORT

6"

1 32

6"

1 3

B

B

601 West 11th P.O. Box 808



MISCELLANEOUS

LIMITED WARRANTIES

OPERATIONS & MAINTENANCE

LIFTING & HANDLING

INSTRUCTIONS


WENDLAND MANUFACTURING CORP.

LIMITED WARRANTY FOR TANKS UNDER 36” OD This warranty applies to the original owner at the original installation address only. Should premature failure occur and subsequent examination reveal that the tank lining has failed under the terms of this warranty, at Wendland Manufacturing Corp.’s option, the lining will be repaired or replaced F.O.B. factory, San Angelo, Texas in accordance with the following schedule: WARRANTY PERIOD/UNIT COST TYPE OF LINING 1st yr. CONSECUTIVE YEARS HOT DIP GALVANIZED No Charge No Warranty Available EPOXOLINE No Charge No Warranty Available CEMENTLINE No Charge No Warranty Available NOTIFICATION: If a failure should occur under the terms of this warranty, notice shall

be in writing from the owner or his representative and addressed to Wendland Manufacturing Corp. Notice shall include tank serial number, date manufactured, date installed, installation location, from whom purchased and description of failure. Warranty is considered in effect from date of shipment.

LIMITATIONS: 1. This warranty does not cover any tank not installed in accordance

with applicable codes and ordinances. This warranty is void if working pressure exceeds the allowable working pressure stamped on the tank, neither is it applicable where the temperature of the water stored is in excess of recommended use. This warranty does not cover damages incurred if dielectric bushings are not included in plumbing, or from damages resulting from loose or damaged fittings installed by others.

2. This warranty does not cover any labor, freight, or installation cost,

either for its original purchase or its replacement. This warranty is in lieu of all other warranties expressed or implied, and of all other obligations or liabilities on our part and we neither assume nor authorize any person to assume for us any other obligations or liabilities in connection with the sale of the tank. The Manufacturer shall not be liable by virtue of this warranty or otherwise for damages to any person or property.


WENDLAND MANUFACTURING CORP.

LIMITED WARRANTY FOR TANKS 36” OD AND LARGER This warranty applies to the original owner at the original installation address only. Should premature failure occur and subsequent examination reveal that the tank lining has failed under the terms of this warranty, at Wendland Manufacturing Corp.’s option, the lining will be repaired or replaced F.O.B. factory, San Angelo, Texas in accordance with the following schedule: WARRANTY PERIOD/UNIT COST TYPE OF LINING 1st yr. 2nd yr. 3rd yr. 4th yr. 5th yr. HOT DIP GALVANIZED No Charge None None None None EPOXOLINE No Charge No Charge No Charge No Charge No Charge CEMENTLINE 1-6 years No Charge, 7th year thru 10th year Prorated Warranty 7th year 20% of list price, 8th year 40% of list price, 9th year 60% of list price, 10th year 80% of list price NOTIFICATION: If a failure should occur under the terms of this warranty, notice shall

be in writing from the owner or his representative and addressed to Wendland Manufacturing Corp. Notice shall include tank serial number, date manufactured, date installed, installation location, from whom purchased and description of failure. Warranty is considered in effect from date of shipment.

LIMITATIONS: 1. This warranty does not cover any tank not installed in accordance

with applicable codes and ordinances. This warranty is void if working pressure exceeds the allowable working pressure stamped on the tank, neither is it applicable where the temperature of the water stored is in excess of recommended use. This warranty does not cover damages incurred if dielectric bushings are not included in plumbing, or from damages resulting from loose or damaged fittings installed by others.

2. This warranty does not cover any labor, freight, or installation cost,

either for its original purchase or its replacement. This warranty is in lieu of all other warranties expressed or implied and of all other obligations or liabilities on our part and we neither assume nor authorize any person to assume for us any other obligations or liabilities in connection with the sale of the tank. The Manufacturer shall not be liable by virtue of this warranty or otherwise for damages to any person or property.


Wendland Manufacturing Corp.P.O. Box 808 San Angelo, Texas 76902

Telephone: (325) 655-6778 Fax: (325) 655-0325 E-Mail: [email protected]

OPERATION AND MAINTENANCE INSTRUCTIONS

FOR: Storage tanks, water heaters, and other pressure vessels.

OPERATION:

A. CAUTION: DO NOT FIELD WELD to any pressure-retaining component on an ASMEstamped pressure vessel.

B. All epoxy-lined vessels should be connected using dielectric isolators to form a breaker

between dissimilar metals. Failure to do so, will cause electrolysis that WILL damagethe interior lining. Failure to install dielectric isolators will void the warranty on thetank and/or heater.

C. Check all connections for proper hook-up. Make sure any unused connections are plugged

tightly. D. Before starting up, fill tank with cold water, venting all air from the system. Check for leaks

with city/county water pressure on system. E. After inspection, start the circulator (when applicable), open valves in lines supplying heating

medium to tank heating coil (when applicable). Do NOT open heating medium to heatingcoil until tank is filled with water. Severe damage can be done to heating coil otherwise.

F. Watch temperature of water in tank and set controls to provide desired outlet temperature,

using appropriate temperature (when applicable) and use appropriate control instructions. G. Check safety valves for free operation by lifting lever on side of valve and releasing. Valve

should re-seat. IF THE VALVE APPEARS TO FUNCTION IMPROPERLY, REPLACE ITIMMEDIATELY!

H. Approximately ten (10) gallons of water should be left in all cement-lined tanks or heaters

before installation to prevent the lining from drying out and cracking.

MAINTENANCE:

A. To open and/or inspect the interior of a tank or water heater, FIRST SHUT DOWN ALLFEED SERVICE LINES (water, air, steam, boiler water, etc.) to the tank or water heater. Besure that the vessel is DRAINED of contents BEFORE opening manholes/inspection ports orother connections. Be sure all pressure is relieved from the vessel prior to removing anyopenings.


Wendland Manufacturing Corp. MAINTENANCE (con’t) B. Open up vessel at least every twelve-(12) months provided manholes/inspection ports are

furnished. Wash out all sediment and inspect interior of tank for corrosion or otherproblems.

C. If tank is lined with a corrosion resistant lining such as Cemaline or Epoxoline, inspect for

damage to the lining. If magnesium anodes were supplied originally, check for possiblerequired replacement of anodes.

D. On Epoxy lined vessels, the Inspector should enter the tank wearing socks -- NOT SHOES!

SHOES AS WELL AS OTHER ABRASIVE ARTICLES WILL DAMAGE THE LINING. E. If tank lining is damaged or in need of repair, check with tank manufacturer for possible

suggested repair instructions. F. Clean off gasket surface of manhole/inspection ports, install new gaskets, pull up all

fasteners, and tighten securely. Check for any leaks and then fill vessel with cold water. G. On a water heater…if the heating coil is removed for inspection, replace the gaskets, tighten

the bolts securely, check for leaks, and reconnect the heating medium piping (CLOSED) tothe heating coil.

H. Inspect the vessel and all connections for leaks. I. Check relief valve for free operation. In case of malfunction or questionable operation,

REPLACE THE VALVE(S). J. With tank filled with water, supply heating medium to tank heating coil (when applicable),

start up circulator (when applicable), and check temperature controls for proper operation(when applicable).

WARNING: NEVER ALLOW THE INTERNAL AIR PRESSURE TO EXCEED THEDESIGN PRESSURE SHOWN ON THE WENDLAND LABEL ON THEVESSEL, AND DO NOT ALLOW THE WATER TEMPERATURE INSIDETO EXCEED THE RECOMMENDED MAXIMUM TEMPERATURE FORWHICH THE INTERIOR LINING IS RATED.

Following these simple instructions will assure the owner many years of safe, trouble-free andefficient operation.


Wendland Manufacturing Corp.P.O. Box 808 San Angelo, Texas 76902

Telephone: (325) 655-6778 Fax: (325) 655-0325 E-Mail: [email protected]

HANDLING AND LIFTING INSTRUCTION

1. ALWAYS USE THE LIFTING LUGS. To prevent damage to the interior lining, donot hook into the connections on the tank. Do not hook into the supports whenhandling. Do not hook into the manway yoke.

2. To avoid damage to the tank or the supports, do not pull, push, roll or drag the tank

when loading, unloading, locating, or handling. Use care when using a forklift tomove or locate the tank.

3. If it is necessary to enter the interior of the tank for inspection, enter with “sock feet”

only. Do not enter the interior of the tank with shoes. This can be very abrasive andmay cause severe damage to the interior lining.




PRICING

Multiplier .................…………………......................... PRICING 1 General Notes.....................................….................. PRICING 2 125 PSI Tanks………………………………………… PRICING 3-5 150 PSI Tanks………………………………………… PRICING 6-8 Flash Tanks…………………………………………… PRICING 9 Expansion Tanks……………………………………… PRICING 10 Angle Legs, Saddles, & Skirts………………………. PRICING 11-12 Nozzles, Manways, Handholes, & Accessories…… PRICING 13-16 Tank Heating Units…………………………………… PRICING 17-20 Insulation & Metal Jacket……………………………. PRICING 21-22

MANUFACTURERS/REPRESENTATIVES DISCOUNT SHEET FOR PRICE LIST

DESCRIPTION MULTIPLIER

Standard 125# & 150# Water Tanks .50 Insulation & Jacket .50 Nozzle Accessories .50 Mounting Accessories & Lifting Lugs .50 Heating Units .50 Air Receivers .50 Air Receivers Nozzle & Accessories .50 Air Separators .50 Expansion & Compression Tanks (C-Series) .50 Flash Tanks .50 Blow-Down Tanks .50 Air Separator Tanks .50 National Board Registration Fees .50

PRICES EFFECTIVE October 1, 2004 PRICES AND MULTIPLIER SUBJECT TO CHANGE

WENDLAND MANUFACTURING CORP. 10-01-2004 PRICING 1


- WENDLAND MANUFACTURING TANKS -GENERAL NOTES FOR WATER STORAGE TANKS

1. Prices do not include any supports, lifting lugs, or special accessories. These must be added tothe base price of the tank.

2. A 12” x 16” manway is included in unlined tanks 42” diameter and greater. 3. All Epoxoline and Cement lined tanks 36” diameter and greater have 12” x 16” manways

included in price. 4. 24”, 30” and 36” diameter unlined tanks do not have manways. They have (2) 2” half-coupling

inspection openings. If manway is required in unlined vessels, deduct (2) 2” half couplings andadd the manway. Refer to nozzle accessories in section PRICING 14-16.

5. A standard set of steel openings is included in tank pricing. If other than standard openings arerequired, refer to nozzle accessories in section PRICING 14-16.

6. Cement lining adds 8 lbs. per square foot to the tank shipping weight. 7. For galvanized tanks consult the factory for pricing. 8. Except for galvanized tanks, all vessels are power tool cleaned per SSPC-SP-3-63 and painted

with one coat of standard shop primer. 9. Threaded connections (couplings) larger than 3” cannot be used when the maximum allowable

working pressure exceeds 125 psi. Per the A.S.M.E. Code, these connections must be flanged. 10. Interpolation for in-between lengths of vessels is not permissible. You must price vessel the

next larger size. 11. All vessels are A.S.M.E. Code, Section VIII, Division 1 and “U” stamped. You must supply us

the end user’s name and address with your purchase order for Data Report purposes. NationalBoard registration is available at an extra charge when required or specified. It is yourresponsibility to determine if National Board registration is a requirement. A NationalBoard number cannot be added to the vessel data report AFTER the vessel has shipped.Registration fees are as follows:

- NATIONAL BOARD REGISTRATION FEES -

0 sq. ft. - 60 sq. ft. $ 30.00 list price61 sq. ft. - 100 sq. ft. $100.00 list price101 sq. ft. - & over $220.00 list price

12. Optional shipping containers to prevent in transit damage by motor freight carriers is nowavailable at your option. Tanks will be banded to a wood or metal shipping skid for protection.Net price for this optional container is as follows:

24” - 36” Diameter tanks $25.00 each 42” - 48” Diameter tanks $35.00 each 54” - 60” Diameter tanks $50.00 each

13. Tanks may be insulated and metal jacketed. Standard insulation is 2” thick to meet ASHRAEspecification 90.1-1989. Metal jacket is extra heavy 14-gauge material.

14. Spray Foam insulation is also available. Wendland uses polyurethane foam, R-16 withweatherproof topcoat. These tanks require protective skidding and special shipping arrangements.Consult the factory for Spray Foam Pricing. Please include the shipping container pricing fromthe chart in number 12 of this page.

WENDLAND STANDARD STORAGE TANKS - LIST PRICES

125 PSI ASME CODE

CATALOG NO. OAL SQ FT GALLONS BLACK WEIGHT EPOXOLINE CEMENT(1)WS-24-3 51" 28 91 $1,355 224 N/A (2) N/AWS-24-4 63" 34 114 $1,452 272 N/A (2) N/AWS-24-5 75" 40 137 $1,572 320 N/A (2) N/AWS-24-6 87" 46 159 $1,683 368 N/A (2) N/AWS-24-7 99" 53 182 $1,920 416 N/A (2) N/AWS-24-8 111" 59 205 $2,027 464 N/A (2) N/A

WS-30-4 66" 45 185 $1,685 374 N/A (2) $2,905WS-30-5 78" 53 220 $1,824 434 N/A (2) $3,172WS-30-6 90" 60 256 $1,958 494 N/A (2) $3,418WS-30-7 102" 68 292 $2,254 554 N/A (2) $3,842WS-30-8 114" 75 328 $2,387 614 N/A (2) $4,087WS-30-9 126" 82 364 $2,521 675 N/A (2) $4,333

WS-36-4NM 68" 54 271 $1,932 601 N/A N/AWS-36-5NM 80" 63 322 $2,074 697 N/A N/AWS-36-6NM 92" 73 374 $2,216 793 N/A N/AWS-36-7NM 104" 82 426 $2,533 889 N/A N/AWS-36-8NM 116" 92 478 $2,676 985 N/A N/AWS-36-9NM 128" 101 530 $2,818 1,081 N/A N/AWS-36-10NM 140" 110 581 $2,963 1,178 N/A N/A

WS-36-4 68" 54 271 $2,702 679 $3,134 $3,566WS-36-5 80" 63 322 $2,843 775 $3,347 $3,851WS-36-6 92" 73 374 $2,986 874 $3,570 $4,154WS-36-7 104" 82 426 $3,410 967 $4,066 $4,722WS-36-8 116" 92 478 $3,554 1,063 $4,290 $5,026WS-36-9 128" 101 530 $3,696 1,159 $4,504 $5,312WS-36-10 140" 110 581 $3,841 1,256 $4,721 $5,601

WS-42-4 70" 67 378 $3,821 799 $4,357 $4,692WS-42-5 82" 78 448 $4,036 911 $4,660 $5,050WS-42-6 94" 89 518 $4,235 1,023 $4,947 $5,392WS-42-7 106" 100 588 $4,703 1,135 $5,503 $6,003WS-42-8 118" 110 659 $5,073 1,247 $5,953 $6,503WS-42-9 130" 121 729 $5,302 1,360 $6,270 $6,875WS-42-10 142" 132 799 $5,529 1,472 $6,585 $7,245WS-42-11 154" 148 870 $5,898 1,584 $7,082 $7,822WS-42-12 166" 154 940 $5,936 1,696 $7,168 $7,938WS-42-13 178" 170 1010 $6,142 1,808 $7,502 $8,352

WS-48-4 74" 80 508 $4,235 930 $4,875 $5,275WS-48-5 86" 93 601 $4,478 1,058 $5,222 $5,687WS-48-6 98" 105 693 $4,721 1,187 $5,561 $6,086WS-48-7 110" 118 785 $5,239 1,315 $6,183 $6,773WS-48-8 122" 130 877 $5,644 1,443 $6,684 $7,334WS-48-9 134" 142 969 $5,892 1,571 $7,028 $7,738WS-48-10 146" 155 1061 $6,135 1,699 $7,375 $8,150WS-48-11 158" 167 1153 $6,378 1,827 $7,714 $8,549WS-48-12 170" 180 1245 $6,624 1,956 $8,064 $8,964WS-48-13 182" 192 1337 $6,868 2,084 $8,404 $9,364WS-48-14 194" 205 1429 $7,111 2,212 $8,751 $9,776(1) Add 8 lbs. per sq. ft. to shipping weight for cement lining.(2) Available as galvanized.N/A = Not Available N/M = No Manway



125 PSI ASME CODE

CATALOG NO. OAL SQ FT GALLONS BLACK WEIGHT EPOXOLINE CEMENT(1)WS-54-4 77" 94 663 $4,894 1,124 $5,646 $6,116WS-54-5 89" 108 779 $5,169 1,269 $6,033 $6,573WS-54-6 101" 122 896 $5,443 1,413 $6,419 $7,029WS-54-7 113" 136 1013 $6,061 1,557 $7,149 $7,829WS-54-8 125" 150 1130 $6,531 1,701 $7,731 $8,481WS-54-9 137" 164 1247 $6,801 1,845 $8,113 $8,933WS-54-10 149" 178 1363 $7,073 1,990 $8,497 $9,387WS-54-11 161" 192 1480 $7,347 2,134 $8,883 $9,843WS-54-12 173" 206 1597 $7,621 2,278 $9,269 $10,299WS-54-13 185" 220 1714 $7,892 2,422 $9,652 $10,752WS-54-14 197" 234 1831 $8,050 1,566 $9,922 $11,092WS-54-15 209" 248 1947 $9,011 2,710 $10,995 $12,235WS-54-16 221" 262 2064 $9,301 2,855 $11,397 $12,707WS-54-17 233" 276 2181 $9,585 3,051 $11,793 $13,173

WS-60-4 78" 114 837 $6,086 1,573 $6,998 $7,568WS-60-5 90" 130 981 $6,460 1,773 $7,500 $8,150WS-60-6 102" 146 1125 $6,840 1,973 $8,008 $8,738WS-60-7 114" 162 1269 $7,752 2,173 $9,048 $9,858WS-60-8 126" 177 1413 $8,221 2,374 $9,637 $10,522WS-60-9 138" 193 1557 $8,601 2,574 $10,145 $11,110WS-60-10 150" 208 1700 $8,981 2,774 $10,645 $11,685WS-60-11 162" 224 1844 $9,359 2,974 $11,151 $12,271WS-60-12 174" 240 1988 $9,738 3,175 $11,658 $12,858WS-60-13 186" 256 2132 $11,050 3,375 $13,098 $14,378WS-60-14 198" 272 2276 $11,430 3,575 $13,606 $14,966WS-60-15 210" 287 2420 $11,869 3,775 $14,165 $15,600WS-60-16 222" 302 2564 $12,249 3,976 $14,665 $16,175WS-60-17 234" 318 2707 $12,621 4,176 $15,165 $16,755WS-60-18 246" 334 2851 $12,994 4,376 $15,666 $17,336WS-60-19 258" 350 2995 $13,366 4,577 $16,166 $17,916WS-60-20 270" 366 3139 $13,740 4,777 $16,668 $18,498WS-60-21 282" 381 3283 $14,110 4,977 $17,158 $19,063

WS-66-4 82" 135 1041 $7,118 1,755 $8,198 $8,738WS-66-5 94" 152 1216 $7,534 1,976 $8,750 $9,358WS-66-6 106" 169 1390 $7,951 2,196 $9,303 $9,979WS-66-7 118" 186 1565 $9,005 2,416 $10,493 $11,237WS-66-8 130" 203 1739 $9,461 2,636 $11,085 $11,897WS-66-9 142" 221 1913 $9,902 2,857 $11,670 $12,554WS-66-10 154" 237 2088 $10,319 3,077 $12,215 $13,163WS-66-11 166" 254 2262 $10,736 3,297 $12,768 $13,784WS-66-12 178" 271 2436 $11,152 3,518 $13,320 $14,404WS-66-13 190" 289 2611 $11,569 3,738 $13,881 $15,037WS-66-14 202" 306 2785 $11,949 3,958 $14,397 $15,621WS-66-15 214" 323 2960 $12,522 4,178 $15,106 $16,398WS-66-16 226" 340 3134 $12,887 4,399 $15,607 $16,967WS-66-17 238" 357 3308 $13,897 4,619 $16,753 $18,181WS-66-18 250" 374 3483 $14,296 4,839 $17,288 $18,784WS-66-19 262" 391 3657 $14,694 5,060 $17,822 $19,386WS-66-20 274" 409 3832 $15,093 5,280 $18,365 $20,001WS-66-21 286" 426 4006 $15,455 5,500 $18,863 $20,567(1) Add 8 lbs. per sq. ft. to shipping weight for cement lining.(2) Available as galvanized.N/A = Not Available N/M = No Manway



125 PSI ASME CODE

CATALOG NO. OAL SQ FT GALLONS BLACK WEIGHT EPOXOLINE CEMENT(1)WS-72-5 96" 172 1480 $8,188 2,259 $9,564 $10,252WS-72-6 108" 191 1688 $8,630 2,500 $10,158 $10,922WS-72-7 120" 210 1896 $9,260 2,740 $10,940 $11,780WS-72-8 132" 229 2104 $9,715 2,980 $11,547 $12,463WS-72-9 144" 248 2312 $10,991 3,220 $12,975 $13,967WS-72-10 156" 267 2520 $11,427 3,461 $13,563 $14,631WS-72-11 168" 286 2728 $11,864 3,701 $14,152 $15,296WS-72-12 180" 304 2935 $12,301 3,941 $14,733 $15,949WS-72-13 192" 323 3143 $12,932 4,182 $15,516 $16,808WS-72-14 204" 342 3351 $13,369 4,422 $16,105 $17,473WS-72-15 216" 360 3559 $13,831 4,662 $16,711 $18,151WS-72-16 228" 379 3767 $14,271 4,903 $17,303 $18,819WS-72-17 240" 398 3975 $15,494 5,143 $18,678 $20,270WS-72-18 252" 417 4183 $15,922 5,383 $19,258 $20,926WS-72-19 264" 438 4391 $16,342 5,624 $19,846 $21,598WS-72-20 276" 457 4598 $16,766 5,864 $20,422 $22,250WS-72-22 300" 495 5003 $17,602 6,409 $21,562 $23,542WS-72-24 336" 514 5211 $18,354 6,897 $22,466 $24,522

WS-84-5 103" 208 2098 $11,311 3,286 $12,975 $13,807WS-84-6 115" 230 2381 $11,947 3,622 $13,787 $14,707WS-84-7 127" 252 2664 $12,821 3,959 $14,837 $15,845WS-84-8 139" 274 2946 $13,356 4,295 $15,548 $16,644WS-84-10 163" 318 3512 $15,780 4,968 $18,324 $19,596WS-84-12 187" 362 4078 $16,987 5,641 $19,883 $21,331WS-84-14 211" 406 4643 $18,367 6,314 $21,615 $23,239WS-84-16 235" 450 5209 $19,567 6,987 $23,167 $24,967WS-84-18 259" 494 5774 $22,041 7,659 $25,993 $27,969WS-84-20 283" 538 6340 $23,209 8,332 $27,513 $29,665WS-84-22 307" 582 6906 $24,380 9,005 $29,036 $31,364WS-84-24 331" 626 7471 $25,551 9,678 $30,559 $33,063

WS-96-5 108" 250 2850 $13,955 5,363 $15,955 $16,955WS-96-6 120" 275 3218 $14,645 5,876 $16,845 $17,945WS-96-7 132" 300 3587 $15,531 6,388 $17,931 $19,131WS-96-8 144" 325 3957 $16,222 6,901 $18,822 $20,122WS-96-10 168" 375 4695 $19,141 7,926 $22,141 $23,641WS-96-11 180" 400 5064 $19,828 8,439 $23,028 $24,628WS-96-12 192" 425 5434 $20,515 8,952 $23,915 $25,615WS-96-14 216" 475 6172 $22,083 9,977 $25,883 $27,783WS-96-16 240" 525 6911 $23,437 11,002 $27,637 $29,737WS-96-18 264" 575 7649 $26,368 12,027 $30,968 $33,268WS-96-20 288" 625 8387 $27,715 13,053 $32,715 $35,215WS-96-22 312" 675 9126 $29,059 14,078 $34,459 $37,159WS-96-24 336" 725 9,864 $30,410 15,103 $36,210 $39,110WS-96-32 432" 925 12,818 $37,376 19,204 $44,776 $48,476(1) Add 8 lbs. per sq. ft. to shipping weight for cement lining.(2) Available as galvanized.N/A = Not Available N/M = No Manway



150 PSI ASME CODE

CATALOG NO. OAL SQ FT GALLONS BLACK WEIGHT EPOXOLINE CEMENT(1)WS-24-3 51" 28 91 $1,353 224 N/A (2) N/AWS-24-4 63" 34 110 $1,450 272 N/A (2) N/AWS-24-5 75" 40 135 $1,570 320 N/A (2) N/AWS-24-6 87" 46 160 $1,682 368 N/A (2) N/AWS-24-7 99" 53 180 $1,918 416 N/A (2) N/AWS-24-8 111" 59 205 $2,025 464 N/A (2) N/A

WS-30-4 66" 45 185 $1,683 374 N/A (2) $2,903WS-30-5 78" 53 220 $1,822 434 N/A (2) $3,170WS-30-6 90" 60 256 $1,956 494 N/A (2) $3,416WS-30-7 102" 68 292 $2,252 554 N/A (2) $3,840WS-30-8 114" 75 328 $2,385 614 N/A (2) $4,085WS-30-9 126" 82 364 $2,519 675 N/A (2) $4,331

WS-36-4NM 68" 54 271 $2,205 601 N/A N/AWS-36-5NM 80" 63 322 $2,388 697 N/A N/AWS-36-6NM 92" 73 374 $2,573 793 N/A N/AWS-36-7NM 104" 82 426 $2,931 889 N/A N/AWS-36-8NM 116" 92 478 $3,116 985 N/A N/AWS-36-9NM 128" 101 530 $3,299 1,081 N/A N/AWS-36-10NM 140" 110 581 $3,485 1,178 N/A N/A

WS-36-4 68" 54 271 $2,975 679 $3,407 $3,839WS-36-5 80" 63 322 $3,157 775 $3,661 $4,165WS-36-6 92" 73 374 $3,341 871 $3,925 $4,509WS-36-7 104" 82 426 $3,804 967 $4,460 $5,116WS-36-8 116" 92 478 $3,989 1,063 $4,725 $5,461WS-36-9 128" 101 530 $4,172 1,159 $4,980 $5,788WS-36-10 140" 110 581 $4,358 1,256 $5,238 $6,118

WS-42-4 68" 67 378 $3,819 799 $4,288 $4,690WS-42-5 80" 78 448 $4,034 911 $4,580 $5,048WS-42-6 92" 89 518 $4,233 1,023 $4,856 $5,390WS-42-7 104" 100 588 $4,453 1,135 $5,153 $5,753WS-42-8 116" 110 659 $5,071 1,247 $5,841 $6,501WS-42-9 128" 121 729 $5,300 1,360 $6,147 $6,873WS-42-10 140" 132 799 $5,518 1,472 $6,442 $7,234WS-42-11 152" 143 870 $5,714 1,584 $6,715 $7,573WS-42-12 164" 154 940 $5,878 1,696 $6,956 $7,880WA-42-13 176" 165 1010 $6,085 1,808 $7,240 $8,230

WS-48-4 74" 80 508 $4,444 930 $5,004 $5,484WS-48-5 86" 93 601 $4,687 1,058 $5,338 $5,896WS-48-6 98" 105 693 $4,930 1,187 $5,665 $6,295WS-48-7 110" 118 785 $5,377 1,315 $6,203 $6,911WS-48-8 122" 130 877 $6,056 1,443 $6,966 $7,746WS-48-9 134" 142 969 $6,303 1,571 $7,297 $8,149WS-48-10 146" 155 1061 $6,547 1,699 $7,632 $8,562WS-48-11 158" 167 1153 $6,790 1,827 $7,959 $8,961WS-48-12 170" 180 1245 $7,035 1,956 $8,295 $9,375WS-48-13 182" 192 1337 $7,482 2,084 $8,826 $9,978WS-48-14 194" 205 1429 $7,725 2,212 $9,160 $10,390(1) Add 8 lbs. per sq. ft. to shipping weight for cement lining.(2) Available as galvanized.N/A = Not Available N/M = No Manway



150 PSI ASME CODE

CATALOG NO. OAL SQ FT GALLONS BLACK WEIGHT EPOXOLINE CEMENT *WS-54-4 77" 94 663 $5,096 1,124 $5,848 $6,318WS-54-5 89" 108 779 $5,371 1,269 $6,235 $6,775WS-54-6 101" 122 896 $5,645 1,413 $6,621 $7,231WS-54-7 113" 136 1013 $6,121 1,557 $7,209 $7,889WS-54-8 125" 150 1130 $6,936 1,701 $8,136 $8,886WS-54-9 137" 164 1247 $7,206 1,845 $8,518 $9,338WS-54-10 149" 178 1363 $7,478 1,990 $8,902 $9,792WS-54-11 161" 192 1480 $7,751 2,134 $9,287 $10,247WS-54-12 173" 206 1597 $8,026 2,278 $9,674 $10,704WS-54-13 185" 220 1714 $8,499 2,422 $10,259 $11,359WS-54-14 197" 234 1831 $8,657 2,566 $10,529 $11,699WS-54-15 209" 248 1947 $9,618 2,710 $11,602 $12,842WS-54-16 221" 262 2064 $9,909 2,855 $12,005 $13,315WS-54-17 233" 276 2181 $10,192 3,051 $12,400 $13,780

WS-60-4 80" 114 837 $6,288 1,573 $7,200 $7,770WS-60-5 92" 130 981 $6,663 1,773 $7,703 $8,353WS-60-6 104" 146 1125 $7,043 1,973 $8,211 $8,941WS-60-7 116" 162 1269 $8,157 2,173 $9,453 $10,263WS-60-8 128" 177 1413 $8,626 2,374 $10,042 $10,927WS-60-9 138" 193 1557 $9,006 2,574 $10,550 $11,515WS-60-10 150" 208 1700 $9,386 2,774 $11,050 $12,090WS-60-11 162" 224 1844 $9,763 2,974 $11,555 $12,675WS-60-12 174" 240 1988 $10,143 3,175 $12,063 $13,263WS-60-13 186" 256 2132 $11,658 3,375 $13,706 $14,986WS-60-14 198" 272 2276 $12,037 3,575 $14,213 $15,573WS-60-15 210" 287 2420 $12,476 3,775 $14,772 $16,207WS-60-16 222" 302 2564 $12,856 3,976 $15,272 $16,782WS-60-17 234" 318 2707 $13,228 4,176 $15,772 $17,362WS-60-18 246" 334 2851 $13,601 4,376 $16,273 $17,943WS-60-19 258" 350 2995 $13,973 4,577 $16,773 $18,523WS-60-20 270" 366 3139 $14,347 4,777 $17,275 $19,105WS-60-21 282" 381 3283 $14,717 4,977 $17,765 $19,670

WS-66-4 82" 135 1041 $6,626 2,090 $7,706 $8,246WS-66-5 94" 152 1216 $6,945 2,354 $8,161 $8,769WS-66-6 106" 169 1390 $7,276 2,618 $8,628 $9,304WS-66-7 118" 186 1565 $8,401 2,883 $9,889 $10,633WS-66-8 130" 203 1739 $8,696 3,147 $10,320 $11,132WS-66-9 142" 221 1913 $9,060 3,411 $10,828 $11,712WS-66-10 154" 237 2088 $9,406 3,676 $11,302 $12,250WS-66-11 166" 254 2262 $9,751 3,940 $11,783 $12,799WS-66-12 178" 271 2436 $10,037 4,204 $12,205 $13,289WS-66-13 190" 289 2611 $10,571 4,469 $12,883 $14,039WS-66-14 202" 306 2785 $10,902 4,733 $13,350 $14,574WS-66-15 214" 323 2960 $11,234 4,997 $13,818 $15,110WS-66-16 226" 340 3134 $11,642 5,262 $14,362 $15,722WS-66-17 238" 357 3308 $12,420 5,526 $15,276 $16,704WS-66-18 250" 374 3483 $12,750 5,790 $15,742 $17,238WS-66-19 262" 391 3657 $13,072 6,055 $16,200 $17,764WS-66-20 274" 409 3832 $13,394 6,319 $16,666 $18,302WS-66-21 286" 426 4006 $13,665 6,583 $17,073 $18,777(1) Add 8 lbs. per sq. ft. to shipping weight for cement lining.(2) Available as galvanized.N/A = Not Available N/M = No Manway


WENDLAND STANDARD WATER STORAGE TANKS - LIST PRICES

150 PSI ASME CODE

CATALOG NO. OAL SQ FT GALLONS BLACK WEIGHT EPOXOLINE CEMENT *WS-72-5 96" 172 1480 $9,420 2,658 $10,796 $11,484WS-72-6 108" 191 1688 $9,937 2,946 $11,465 $12,229WS-72-7 120" 210 1896 $10,642 3,234 $12,322 $13,162WS-72-8 132" 229 2104 $11,172 3,523 $13,004 $13,920WS-72-9 144" 248 2312 $12,523 3,811 $14,507 $15,499WS-72-10 156" 267 2520 $13,035 4,099 $15,171 $16,239WS-72-11 168" 286 2728 $13,547 4,388 $15,835 $16,979WS-72-12 180" 304 2935 $14,059 4,676 $16,491 $17,707WS-72-13 192" 323 3143 $14,766 4,964 $17,350 $18,642WS-72-14 204" 342 3351 $15,296 5,253 $18,032 $19,400WS-72-15 216" 360 3559 $15,815 5,541 $18,695 $20,135WS-72-16 228" 379 3767 $16,338 5,830 $19,370 $20,886WS-72-17 240" 398 3975 $17,643 6,118 $20,827 $22,419WS-72-18 252" 417 4183 $18,150 6,406 $21,486 $23,154WS-72-19 264" 438 4391 $18,656 6,695 $22,160 $23,912WS-72-20 276" 457 4598 $19,670 6,971 $23,326 $25,154WS-72-22 300" 495 5003 $20,175 7,560 $24,135 $26,115WS-72-24 324" 531 5511 $21,133 8,136 $25,381 $27,505

WS-84-5 103" 208 2098 $11,739 3,282 $13,403 $14,235WS-84-6 115" 230 2381 $12,346 3,618 $14,186 $15,106WS-84-7 127" 252 2664 $13,202 3,955 $15,218 $16,226WS-84-8 139" 274 2946 $13,827 4,291 $16,019 $17,115WS-84-10 163" 318 3512 $16,229 4,964 $18,773 $20,045WS-84-12 187" 362 4078 $17,487 5,637 $20,383 $21,831WS-84-14 211" 406 4643 $18,864 6,310 $22,112 $23,736WS-84-16 235" 450 5209 $20,078 6,982 $23,678 $25,478WS-84-18 259" 494 5774 $22,649 7,655 $26,601 $28,577WS-84-20 283" 538 6340 $23,745 8,328 $28,049 $30,201WS-84-22 307" 582 6906 $24,916 9,001 $29,572 $31,900WS-84-24 331" 626 7471 $26,087 9,674 $31,095 $33,599

WS-96-5 108" 250 2850 $15,377 4,605 $17,377 $18,377WS-96-6 120" 275 3218 $16,268 5,118 $18,468 $19,568WS-96-7 132" 300 3587 $17,354 5,630 $19,754 $20,954WS-96-8 144" 325 3957 $18,246 6,143 $20,846 $22,146WS-96-10 168" 375 4695 $21,693 7,168 $24,693 $26,193WS-96-11 180" 400 5064 $22,585 7,681 $25,785 $27,385WS-96-12 192" 425 5434 $23,478 8,193 $26,878 $28,578WS-96-14 216" 475 6172 $25,456 9,219 $29,256 $31,156WS-96-16 240" 525 6911 $27,220 10,244 $31,420 $33,520WS-96-18 264" 575 7649 $30,612 11,269 $35,212 $37,512WS-96-20 288" 625 8387 $32,408 12,295 $37,408 $39,908WS-96-22 312" 675 9126 $34,167 13,320 $39,567 $42,267WS-96-24 336" 725 9,864 $35,931 14,345 $41,731 $44,631WS-96-32 432" 925 12,818 $44,658 18,446 $52,058 $55,758(1) Add 8 lbs. per sq. ft. to shipping weight for cement lining.(2) Available as galvanized.N/A = Not Available N/M = No Manway


ASME CODE FLASH TANKS - LIST PRICES

MODEL SIZE LIST WEIGHTFT-15 12” X 30” $562 48

FT-24 12” X 50” $683 83

FT-30 14” X 50” $920 100

FT-40 16” X 50” $906 118

FT-60 16” X 70” $1,034 157

FT-80 20” X 60” $1,167 175

FT-100 20” X 72” $1,278 207

FT-120 24” X 61” $1,265 224

FT-140 24” X 73” $1,387 259

FT-175 30” X 65” $1,780 442

FT-250 30” X 89” $2,020 542

NOTES:

1. All prices are “LIST” F.O.B. Factory, San Angelo, Texas. Add for freight.

2. Flash tanks are A.S.M.E. stamped for 150 psi design pressure.

3. Price includes inspection openings as required. Price includes spray pipe.

4. If National Board registration is required, add $30.00 to the list price.

5. If a 4” X 6” hand-hole is required, add $150.00 to list price and 7 lbs. to weight.

6. Exterior is cleaned and standard shop primer painted only.

7. Any deviations from this “standard” will result in a price increase. Call the factory for price changes.


ASME CODE EXPANSION - COMPRESSION TANKS - LIST PRICES

CATALOG MODEL NO.

LIST PRICE PRIME PAINTEDSIZE WEIGHT

C-15 12” X 30” $480 82

C-24 12” X 50” $561 122

C-30 14” X 50” $619 132

C-40 16” X 50” $663 153

C-60 16” X 70” $788 206

C-80 20” X 60” $792 200

C-100 20” X 72” $892 240

C-120 24” X 61” $919 252

C-140 24” X 73” $1,035 300

C-175 30” X 65” $1,254 368

C-250 30” X 89” $1,496 488

NOTES:

1. All prices are “LIST” F.O.B. Factory, San Angelo, Texas. Add for freight.

2. Expansion - Compression tanks are A.S.M.E. stamped for 150 psi design pressure.

3. If National Board registration is required, add $30.00 to the list price.

4. For other sizes, call for an estimate.

5. Exterior is cleaned and standard shop primer painted only.

6. Any deviations from “standard” tappings will be quoted on application.

7. Any deviations from the “standard” will result in a price increase. Call factory for price changes.



BLOW DOWN TANKS LIST PRICES

CATALOG MODEL NO.

SIZE

LIST PRICE BLACK

WEIGHT

BD243V 24” X 36” $3,655 541#

BD305V 30” X 60” $4,805 960#

BD365V 36” X 60” $6,195 1201#

BD367V 36” X 84” $6,300 1559#

BD425V 42” X 60” $8,085 1433#

BD485V 48” X 60” $9,550 1879#

BD604V 60” X 48” $11,115 2376# NOTES: 1. All prices are “LIST” F.O.B. Factory, San Angelo, Texas. Add for freight. 2. Prices include supports. Vertical tanks have angle legs and horizontal tanks have saddles

welded to the tank. 3. Blow Down tanks are A.S.M.E. stamped for 150-psi design pressure. 4. National Board registration is included in the price. 5. For other sizes, call for an estimate. 6. Exterior is cleaned and standard shop primer painted only. 7. Any deviations from “standard” tappings will be quoted on application. 8. Any deviations from the “standard” will result in a price increase. Call factory for price

changes.

MOUNTING ACCESSORIES FOR TANKS - LIST PRICES

ANGLE LEGS WFI BEAM LEGS SADDLE SUPPORTS (LOOSE) TO WELD STYLE I STYLE II SADDLES

TANK DIA. PRICE WT PRICE WT PRICE WT PRICE WT TO TANK

12" $152 25 N/A N/A $142 15 N/A N/A $7014" $152 25 N/A N/A $144 17 N/A N/A $7016" $152 25 N/A N/A $148 21 N/A N/A $7018" $152 25 N/A N/A $148 21 N/A N/A $7020" $152 25 N/A N/A $148 22 N/A N/A $7024" $202 34 N/A N/A $162 26 N/A N/A $7030" $222 50 N/A N/A $262 45 N/A N/A $8036" $222 50 N/A N/A $268 51 $530 110 $10042" $306 78 N/A N/A $298 56 $578 150 $13048" $314 85 N/A N/A $434 136 $676 175 $16054" $318 85 N/A N/A $502 146 $760 194 $18060" $564 178 N/A N/A N/A N/A $896 273 $20066" $564 178 N/A N/A N/A N/A $982 303 $25072" $568 178 $2,296 320 N/A N/A $1,068 317 $27584" $946 317 $2,482 395 N/A N/A $2,394 744 $60096" $996 356 $2,920 628 N/A N/A $2,878 966 $750

STYLE I SKIRTS - 6" High STYLE II SKIRTS - 12" HighNO ANGLE CLIPS WITH ANGLE CLIPS NO ANGLE CLIPS WITH ANGLE CLIPS

TANK DIA. PRICE WT PRICE TANK DIA. PRICE WT PRICE

24" $146 30 $176 24" $182 51 $21230" $162 39 $192 30" $202 63 $23236" $194 53 $224 36" $244 83 $27442" $204 63 $234 42" $260 99 $29048" $298 64 $328 48" $366 100 $39654" $438 108 $468 54" $528 164 $55860" $530 140 $560 60" $634 204 $66466" $622 170 $652 66" $738 242 $76872" $756 202 $786 72" $908 282 $93884" $1,108 341 $1,138 84" $1,300 462 $1,33096" $1,464 533 $1,494 96" $1,750 701 $1,780

N/A = Not Available


MOUNTING ACCESSORY NOTES

1. Tanks 20" diameter and smaller with angle leg supports will have three (3) angle legs.2. If tanks require lifting loops, add per price LIST.3. See Nozzles & Heating Bundle Pricing Section for tube bundle related accessories and adders.4. All saddles are 6" high, and shipped loose unless otherwise priced.5. All vertical tank standard mounting accessories are 12" high with the exception of Style skirts which are 6" high.

LIFTING LOOP ADDS

TANK SIZE LIST PRICE

12" OD thru 30" OD $12.00 each36" OD thru 48" OD $20.00 each54" OD thru 72" OD $30.00 each84" OD and above $50.00 each


NOZZLE ACCESSORIES - LIST PRICES

STANDARD OPENINGS INCLUDED IN ALL A.S.M.E. STORAGE TANK PRICING

TANK DIAMETER STANDARD 3000# OPENINGS INCLUDED TOTAL VALUE (LIST) PRICE

24” & 30” (4)1-1/2” H. Cplg’s; (1)1-1/4” H. Cplg; (1)1” H. Cplg; $250(1)3/4” F. Cplg; & (1)1/2” F. Cplg

36” & 42” (3)2” H. Cplg’s; (1)1-1/2” H. Cplg; (1)1” H. Cplg; $275(1)1-1/4” H. Cplg; (1)3/4” F. Cplg; & (1)1/2” F Cplg.

48” & Above (4)2” H. Cplg; (1)1-1/2” H. Cplg; (1)1-1/4” H. Cplg; $300(1)3/4” F. Cplg; (1)1/2” F. Cplg.

STANDARD OPENING NOTES

1. If other than standard opening sizes or quantities are required, deduct standard opening value shown above and add for openings as required. Use multiplier accordingly to above pricing. 2. No consideration is given in the above listings for inspection openings or for an inspection manway.

OTHER OPENING NOTES

1. Blind flange prices are for blind flange, bolts, and gasket only. Price must be added to flange nozzle. 2. Unlined tank coupling prices are welded from the outside only. If couplings are required to be welded inside and outside, use lined tank coupling prices. 3. Lined tank couplings are welded inside and outside. 4. Cement lined tanks require FULL COUPLINGS for 2” size and below. All cement lined tanks priced in the “standard” price sheets INCLUDE the full couplings in that price.



CARBON STEEL 304 STAINLESS STEEL 316 STAINLESS STEEL3000# COUPLINGS 3000# COUPLINGS 3000# COUPLINGS

SIZE HALF CPLG FULL CPLG HALF CPLG FULL CPLG HALF CPLG FULL CPLG1/2” N/A $32 N/A $34 N/A $363/4” N/A $38 N/A $44 N/A $461” $40 $40 $44 $46 $46 $52

1-1/4” $48 $50 $58 $70 $60 $721-1/2” $50 $52 $60 $76 $70 $76

2” $50 $54 $68 $82 $80 $882-1/2” $60 $72 $112 $144 $136 $190

3” $120 $138 $176 $218 $204 $2664" $188 $236 $278 $334 $332 $374

150# RFSO STEEL 300# RFSO STEEL 304 STAINLESS STEELFLANGE NOZZLE FLANGE NOZZLE 150# RFSO FLANGE

LIST LIST LISTSIZE WT PRICE WT PRICE WT PRICE

1” 3 $154 6 $230 3 $1541-1/2” 5 $172 6 $246 5 $172

2” 7 $170 9 $254 7 $1702-1/2" 12 $192 14 $262 12 $192

3” 14 $226 18 $304 14 $2264” 19 $290 28 $372 19 $2905" 23 $364 36 $458 23 $3646” 38 $410 55 $506 38 $4108” 58 $656 84 $778 58 $656

10" 75 $828 116 $992 75 $82812" 106 $1,016 156 $1,168 106 $1,01614" 128 $1,176 215 $1,754 128 $1,17616" 151 $1,390 278 $1,922 151 $1,39018" 185 $1,632 345 $2,270 185 $1,63220" 272 $1,908 442 $2,570 272 $1,90824" 377 $2,380 657 $3,538 377 $2,380

NOTE: Repads may be required on flanges 6” diameter and larger. If a repad is required, there will be an added charge for this. CONSULT THE FACTORY! N/A = Not Available



316 STAINLESS STEEL 150# STEEL BLIND150# RFSO FLANGE W/BOLTS & 1/16"

COMP. ASB. GASKETLIST LIST

SIZE WT PRICE WT PRICE1” 3 $208 4 $28

1-1/2” 5 $248 6 $322” 7 $280 7 $363” 14 $320 15 $404” 19 $418 26 $426” 38 $490 49 $588” 58 $652 77 $92

NOTE: Repads may be required on flanges 6” diameter and larger. If a repad is required, there will be an added charge for this. CONSULT THE FACTORY!

N/A = Not Available



ELLIPTICAL MANWAYS & HANDHOLES

LISTSIZE TYPE WT PRICE

11” X 15” Carbon Steel 77 $53212” x 16” Carbon Steel 85 $56214” X 18” Carbon Steel 105 $8104” X 6” Carbon Steel 6 $132

11” X 15” 304 Stainless Steel 77 $1,85212” X 16” 304 Stainless Steel 85 $2,08814” X 18” 304 Stainless Steel 105 $2,4144” X 6” 304 Stainless Steel 6 $346

REPLACEMENT PARTS

LISTSIZE DESCRIPTION WT PRICE

11” X 15” Carbon Steel Cover 24 $13412” x 16” Carbon Steel Cover 30 $170

11” X 15” 304 Stainless Steel Cover 24 $58612” X 16” 304 Stainless Steel Cover 30 $780

11” X 15” Molded Rubber Gasket $1412” X 16” Molded Rubber Gasket $14 4” X 6” Molded Rubber Gasket $10

MANWAY DAVITS FOR FLANGED MANWAYS

LISTDIAMETER WT PRICE

18” 60 $40020” 70 $45024” 85 $500

The above openings are for 300 psi maximum allowable working pressure. Contact Factory for higher pressure requirements.


TANK HEATING UNIT NOTES

1. The list price includes the heating bundle with 3/4” OD Copper tubes, standard steel tubesheet andthe steam or boiler water head. It also includes installing the collar, installing the bundle, and installingthe coil support if required.

2. Oversized tank heating units (identified with the letters -TB) are required for all cement lined waterheaters.

3. In selecting your tank-heating unit, keep in mind the diameter and length of the shell. Tank heatingunits for vertical heaters should not be longer than the diameter of the tank.

4. If the customer furnished the tank-heating unit, please refer to page HC-4 of this section. Add for installing the collar, installing the bundle, and installing the coil support when required. Also, check to see if a repad is required. CONSULT THE FACTORY.

NOTE:

Tank heating units and collars shipped to us by the customer for installation by WMC must be shipped by PREPAID FREIGHT AND TAGGED WITH YOUR COMPANY NAME AND PURCHASE ORDER NUMBER for which heating bundle unit is to be used. PRIOR TO START OF FABRICATION: The collar must be received along with the A.S.M.E. "partial data report".

5. TA heating units have 3/4” X 20 gauge copper tubing, cast iron heads, and cast iron or steel tubesheets.

6. TB heating units are identical to the TA units except they are furnished with the next larger diameterhead and collar for cement lined applications.

7. For special applications such as bronze, stainless steel, etc. consult the factory.

8. Heating unit model number designation is as follows:10 36 2

Collar Diameter-------- ----------Number of passes of tubesInches

------------------Length of tube bundle

WENDLAND TANK HEATING UNITS - LIST PRICES

STANDARD UNIT

MODEL NO. WT LIST SQ. FT. HEATING LIST PRICELBS. PRICE SURFACE ADDER FOR CEMENT LINED

T4242A 55.1 $970 3.19 $125 T4362A 59.1 $988 4.79 $125 T4482A 63.1 $1,230 6.39 $125 T4602A 65.1 $1,284 7.98 $125 T4722A 71.1 $1,302 9.58 $125 T4842A 83.1 $1,364 $125 11.18



STANDARD UNIT

MODEL NO. WT LIST SQ. FT. HEATING LIST PRICELBS. PRICE SURFACE ADDER FOR CEMENT LINED

T6242A 68.6 $1,324 8 $135 T6362A 76.6 $1,378 12.8 $135 T6482A 90.6 $1,696 17.6 $135 T6602A 103.6 $1,780 22.4 $135 T6722A 116.6 $1,830 27.1 $135 T6842A 122.6 $1,904 31.9 $135

T8242A 113.9 $2,036 15.2 $225 T8362A 131.9 $2,142 24 $225 T8482A 161.9 $2,482 32.7 $225 T8602A 179.9 $2,620 41.5 $225 T8722A 207.9 $2,882 50.3 $225 T8842A 219.9 $2,902 59.1 $225 T8962A 243.9 $3,022 67.9 $225

T10362A 204.8 $3,044 42.3 $360 T10482A 220.8 $3,546 57.5 $360 T10602A 251.8 $3,732 72.7 $360 T10722A 276.8 $3,908 87.8 $360 T10842A 303.8 $4,164 103 $360 T10962A 321.8 $4,340 118.2 $360

T101082A 335.8 $4,622 133.3 $360 T101202A 358.8 $5,200 148.5 $360

Repad from here on included in priceT12362A 307 $4,202 62 $415 T12482A 359 $4,726 84 $415 T12602A 397 $5,164 106 $415 T12722A 455 $5,436 128 $415 T12842A 498 $5,776 150 $415 T12962A 552 $6,076 172 $415

T121082A 601 $6,452 194 $415 T121202A 656 $6,690 216 $415

T14362A 394 $5,908 87 $710 T14482A 470 $6,742 117 $710 T14602A 527 $7,350 147 $710 T14722A 594 $7,994 177 $710 T14842A 648 $8,618 207 $710 T14962A 751 $9,270 237 $710

T141082A 848 $9,930 266 $710 T141202A 938 $10,578 296 $710

T16362A 527 $7,484 115 $815 T16482A 617 $8,568 155 $815 T16602A 699 $9,458 194 $815 T16722A 783 $10,328 233 $815 T16842A 860 $11,210 272 $815 T16962A 985 $12,112 311 $815

T161082A 1053 $13,142 352 $815 T161202A 1103 $13,824 389 $815

WENDLAND MANUFACATURING CORP. 10-01-2004 PRICING 19


NAVAL BRASS/BRONZE TUBESHEET ADDERS

Coil Diameter

List Price

4” $206 6” $220 8” $296 10” $444 12” $786 14” $1,578 16” $1,930

T304 STAINLESS TUBESHEET ADDERS

Coil Diameter

List Price

4” $378 6” $490 8” $710 10” $1,056 12” $1,842 14” $2,186 16” $2,836

CUPRO-NICKEL TUBES ADDERS

Consult Factory

NOTE: Above prices to be added to the coil price from pages PRICING 17 &PRICING 18 if a bronze tubesheet or Type 304 stainless tubesheet isrequired.


ADDITIONS FOR TANK HEATING UNITS - LIST PRICES(For Customer furnished Coil ONLY)

INSTALL HEATING UNIT COLLAR IN TANK

SIZE LIST PRICE

SIZE LIST PRICE

4” $165 12” $426 6” $230 14” $470 8” $230 16” $670

10” $380

INSTALLATION OF TUBE BUNDLE INTO COLLAR

SIZE LIST PRICE

SIZE LIST PRICE

4” $52 12" $162 6” $80 14” $184 8” $94 16” $212

10” $122

HEATING UNIT SUPPORT LIST PRICE FOR CUSTOMER SUPPLIED HEATING UNIT

List PriceCarbon Steel $100

Stainless Steel $160

TANK HEATING UNIT NOTES1. Cement lined tanks or heaters require Stainless Steel Bundle Supports.

2. Repads may be required on heating coils 10” Diameter and larger. If a repad is required, there will be an added charge for this. CONSULT THE FACTORY!

3. You do not need these adders if you get your coil price from PRICING 17 & PRICING 18.

4. These prices are ADDERS - To be added to the Heating Coil prices only when the customer furnishes the heating coil to Wendland.


INSULATION AND METAL JACKET

1. Standard insulation is 2" thick to meet ASHRAE specification 90.1-1989. Metal jacket is extra heavy 14-gauge material.

2. Jacketed vessels are prime painted. This is included in the price listed.

3. Lift lugs are included in the price. (Required for handling)

4. On vertical insulated and jacketed vessels, be sure to add a skirt to the tank pricing. We cannot jacket around angle legs.

5. Add for skid to ship (Price are shown on page PRICING 2).

6. Tank Size is for overall length on tank only. Do not add any other dimensions to these numbers.

Tank Size Sq ft Weight List Price Tank Size Sq ft Weight List Price

24" x 51" 28 112 lbs. $756 48" x 110" 118 472 lbs. $3,00924" x 75" 40 160 lbs. $1,080 48" x 122" 130 520 lbs. $3,31524" x 87" 46 184 lbs. $1,242 48" x 134" 142 568 lbs. $3,62130" x 66" 45 180 lbs. $1,215 48" x 146" 155 620 lbs. $3,95330" x 78" 53 212 lbs. $1,431 48" x 158" 167 668 lbs. $4,25930" x 90" 60 240 lbs. $1,620 48" x 170" 180 720 lbs. $4,59030" x 102" 68 272 lbs. $1,836 48" x 182" 192 768 lbs. $4,89630" x 114" 75 300 lbs. $2,025 48" x 194" 205 820 lbs. $5,22830" x 126" 82 328 lbs. $2,214 54" x 89" 108 432 lbs. $2,75436" x 68" 54 216 lbs. $1,458 54" x 101" 122 488 lbs. $3,11136" x 80" 63 252 lbs. $1,701 54" x 113" 136 544 lbs. $3,46836" x 92" 73 292 lbs. $1,971 54" x 125" 150 600 lbs. $3,82536" x 104" 82 328 lbs. $2,214 54" x 137" 164 656 lbs. $4,18236" x 116" 92 368 lbs. $2,484 54" x 149" 178 712 lbs. $4,53936" x 128" 101 404 lbs. $2,727 54" x 161" 192 768 lbs. $4,89636" x 140" 110 440 lbs. $2,970 54" x 173" 206 824 lbs. $5,25342" x 70" 67 268 lbs. $1,809 54" x 185" 220 880 lbs. $5,61042" x 82" 78 312 lbs. $2,106 54" x 197" 234 936 lbs. $5,96742" x 94" 89 356 lbs. $2,403 54" x 209" 248 992 lbs. $6,32442" x 106" 100 400 lbs. $2,700 54" x 221" 262 1048 lbs. $6,68142" x 118" 110 440 lbs. $2,970 60" x 78" 114 456 lbs. $2,90742" x 130" 121 484 lbs. $3,267 60" x 90" 130 520 lbs. $3,31542" x 142" 132 528 lbs. $3,564 60" x 102" 146 584 lbs. $3,72342" x 154" 148 592 lbs. $3,996 60" x 114" 162 648 lbs. $4,13142" x 166" 154 616 lbs. $4,158 60" x 126" 177 708 lbs. $4,51442" x 178" 170 680 lbs. $4,590 60" x 138" 193 772 lbs. $4,92248" x 98" 105 420 lbs. $2,678 60" x 150" 208 832 lbs. $5,304

60" x 162" 224 896 lbs. $5,712


WENDLAND MANUFACTURING CORPORATION

Documents

Transcript of WENDLAND MANUFACTURING CORPORATION