WELL SERVICING & PRODUCTION EQUIPMENToilstates.com/wp-content/uploads/Oil-States-Well...suspended in...

Oil States WELL SERVICING & PRODUCTION EQUIPMENT

™

TM

Table of Contents

Swab Cups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Swab Cup Reference Chart . . . . . . . . . . . . . . . . . . . .2

Swab Mandrels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Rope Sockets, Wireline Oil Saver . . . . . . . . . . . . . . .4

Rod Stripper Rubbers, Pipe Wipers . . . . . . . . . . . . . .5

Tubing Stripper Rubbers . . . . . . . . . . . . . . . . . . . . .6-7

Tubing Test Cups . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

OSI Sucker Rod Guides . . . . . . . . . . . . . . . . . . . . . .9

OSI Packer Cups . . . . . . . . . . . . . . . . . . . . . . . .10-11

Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Oilfield Products Catalog - Page 1

Swab Cups

Type HL-HD Wire Cups* These wire cups are designated as HL or HD series for Heavy Load or Heavy Duty. The rugged cups are made of strong, flexible spring steel reinforcing wiresinserted into an alloy steel base. This forms the “skeleton” for the tough body ofspecial compounded oilfield rubber to make the ultimate cup for deep, heavy duty service. Available in sizes from 1-1/4” tubing through 7” casing.

Type EL Wire Cups* The EL series wire cup is a strengthened version of Oil States standard HD series cup. Because of the extra length and improved wire arrangement, the ELworks best in heavy load situations. A combination of long and short wires affords maximum wire density in the critical lower load area of the cup. The ELuses the same high-performance oilfield rubber compound as the HD series. Because of the improved wire arrangement and thicker rubber, it is not necessary to use sleeves when running the EL. *Special order only.

Type M Cups The workhorse of the “all-rubber” type cups. The M series utilizes an ideal cup configuration, molded of a special long wearing rubber compound bonded to analuminum or steel sleeve. Type M cups are recommended for deep, heavy dutyjobs as well as medium load work. This is Oil States most popular “all-rubber”cup.

Type RTL Cups Medium to light loads can be adequately handled by this rubber cup. Featuring either steel or aluminum insert sleeves, the RTL cup has a unique “dual lip” feature. The thin lip of the dual lip is the load lip and the heavier long lip is thesupporting portion. The same tough Oil States compound used in the M seriescups makes the RTL cup Rough, Tough, and Long lasting. Available in all popular sizes of tubing in both full size and undersize.

SD Series (Sand Devil) Cups These highly efficient Oil States all-rubber sand swab cups are designed especially for use in problem wells where there is danger of “sticking” due to ahigh ratio of sand suspended in the fluid. They are also highly suitable for liftinglight loads. The number of Sand Devil cups on a mandrel can be varied to fit specific conditions. Available in 2”, 2-1/2” and 3” tubing and 4-1/2”, 5-1/2” and 7" casing sizes.

Type SV Cups SV type swab cups are ideal for use in wells where there is a high ratio of sand suspended in the fluid. These long-life cups are designed to fall fast to speed up swabbing and the flexible lips of the cup automatically expand under a loadto compensate for wear. Available in 2”, 2-1/2” and 3” tubing sizes.

Wireless Cups These Oil States cups are of a wireless design for use as a long-wearing light load cup. Specially compounded heavy rubber cup walls molded around a metal base provide for long service life.

*Patented

HL-HD WireCups

EL WireCups

Type RTLCups

SD Series(Sand Devil)

Cups

Type SVCups

WirelessCups

Type M Cups

Swab Cup Reference Chart


** Sleeves recommended with these swab cups on SJ-20, SJ-21, SJ-25 or SJ-26 mandrels.~ Available with steel or aluminum insert; all others available with steel insert only.

Oil States Casing Swab Cups Part NumbersWire Type

Std.CupO.D.

SD Type CupO.D.

W Type(Wireless)

CupO.D.

RTL Type CupO.D.

454-1 4.01 454-SD-ST 4.00 454-1W 4.12454-2 3.91454-3 3.73504-1 4.37504-2 4.10 504B-RTL-AL 4.25554-1 5.00

554-SD-ST 4.95554-1W 5.10

554-2 4.89554-4 4.73 554-3W 4.99

554B-RTL-AL4.87

554-4 4.73 4.75704-1 6.52

700-SD-ST 6.47704-2 6.30704-3 6.14

Casing DataNom. Csg.

SizeO.D.

(inches)Lbs./Ft. Csg. I.D.

(inches)

4 1/2” 4.5009.5-11.6 4.090-4.000

13.5 3.92015.1 3.826

5” 5.00011.5-15.0 4.560-4.408

18.0 4.276

5 1/2” 5.500

14.0 5.01215.5 4.95017.0 4.89220.0 4.778

7” 7.00017.0 6.538

22.0-23.0 6.456-6.36626.0-29.0 6.276-6184

Oil States Tubing Swab Cups Part NumbersWire Type M Type RTL Type SV Type SD Type

MandrelPartNumber

CupO.D.

PartNumber

CupO.D.

Part NumberCupO.D.

PartNumber

CupO.D.

PartNumber

CupO.D.

124-HL 1.30 124-R~ 1.35 120154-HD 1.57 154-RTL~ 1.58 150154-HY 1.49 154R-HY-AL 1.50 150

216 1.63 216-RTL~ 1.66 150204-HD** 1.92 M-2~ 1.95 204-RTL~ 1.96 204-SV~ 1.96 204-SD 1.99 200, SJ20,

SJ21204-HD** 1.92 UM-2~ 1.93 204-RTL-U~ 1.93238-PH6 1.77 M-1~ 1.76 150254-HD** 2.34 M-5~ 2.39 254-RTL~ 2.39 254-SV~ 2.43 254-SD 2.43 250, SJ25,

SJ26254-HD** 2.34 UM-5~ 2.35 254-RTL-U~ 2.35278-PH6** 2.22 M-7~ 2.24

200, SJ20,SJ21278-DP** 2.12 M-6~ 2.17

278-DP** 2.12 278-R-DP-AL 2.14304-HL 2.97 M-3~ 2.92 304-RTL-ST 2.98 304-SV~ 2.96 304-SD 2.96

250, SJ25,SJ26

304-HY** 2.83350-PH6** 2.62350-DP** 2.56 350R-DP-1~ 2.73350-DP** 2.56 350R-DP-2~ 2.59

Tubing DataNom.Tbg.Size

O.D.(in.)

Lbs. / Ft.I.D.(in.)

Joint BoredI.D. (inches)

1 1/4” 1.660 2.40 1.380

1 1/2” 1.9002.90 1.6103.64 1.500

1 3/4” 2.063 3.40 1.750

2” 2.3754.60-4.70

1.9954.70 1.945- 1.925.95 1.867 1.805

2 1/2” 2.875

6.40-6.50 2.441

6.50 2.375 7.90 2.323 2.2658.70 2.259 2.200

10.40 2.151

3” 3.500

9.20 2.99210.30 2.92212.95 2.750 2.68713.30 2.76415.50 2.602

Swab Mandrels


Components122-U Upper Section

122-L Lower Section

121-A Nose Guide

151-U Upper Section

152-L Lower Section

151-A Nose Guide

Model Size

120~ 1 1/4”

150 1 1/2”

Pin Size5/8” S.R.

5/8” S.R.

5/8” S.R.

5/8” S.R.

5/8” S.R.

5/8” S.R.

Model Size

200~** 2”

250~** 2 1/2”

Components 202 Mandrel

201 Adapter

252 Mandrel

201 Adapter

Pin Size3/4” S.R.

3/4” S.R.

3/4” S.R.

3/4” S.R.

Model Size

SJ-202”

SJ-21~

SJ-252 1/2”

SJ-26~

Pin Size

3/4” S.R.

Components SJ-1 Adapter

SJ-2 Upper SectionSJ-3 Lower Section

SJ-1 AdapterSJ-6 Lower Section

SJ-1 AdapterSJ-4 Upper SectionSJ-5 Lower Section

SJ-1 AdapterSJ-7 Lower Section

** For use with all Rubber Type Cups.~ May be used with Wire Type Cups if sleeves are used.

Two Basic TypesSwab Mandrels from Oil States areavailable for use with wire or “all rubber”type swab cups. Wire type tubing and drillpipe swab cups (1 1/4” through 3 1/2”) canbe used on the “all rubber” type mandrelsby utilizing sleeves available from OilStates.

Maximum Fluid By-PassTubing and drill pipe mandrels are fluted,allowing maximum fluid by-pass whilelowering the mandrel to swabbing depth.Steel mandrels are either machined ordrop forged from high strength alloy steel.All mandrels exceed strengthrequirements for wire rope sizesrecommended for use with mandrels.

Mandrel with NutSpacing

Ring

SKJ-45 MANDREL 1-CUPSKJ-45 RING

SKJ-45 MANDREL 2-CUPSKJ-55 MANDREL 1-CUP

SKJ-55 RINGSKJ-55 MANDREL 2-CUP

Top Section3/4” Pin

SKJ-55 TOP

SKJ-55 TOP

Model

SKJ-45, 1 CUPSKJ-45, 2 CUPSKJ-55, 1 CUPSKJ-55, 2 CUP

120 or150

TubingSwab

Mandrel

SJ-21 orSJ-26

Mandrel

SJ-20 orSJ-25SwivelJoint

Mandrel

Tubing Mandrels for Wire or All Rubber Type Cups

Straight Mandrels for use with All Rubber Type Cups**

SKJ Series Knuckle Joint Swab Mandrels

Swivel Joint Mandrels

Oil Saver Bushings PreventsPremature Rubber WearBy centering the wireline in the oil saver unit,Oil Saver Bronze Bushings prevent prematurewear on the rubbers, as well as othercomponents in the oil saver unit.

Simple Installation and RemovalOil States bushings are equipped withconvenient spring clips for easy installation andremoval from the wireline.

Part Number Bushing TypeUsed w/

Rubber NumberOS-GA Guiberson “H” GAOS-GA-3/4”

Rope Sockets, Wireline Oil Saver


Sure Swivel Rope Sockets - Fish Neck GroovesRope Sockets are constructed of high quality materials andare continuously checked for even the slightest defect. Fishneck grooves are incorporated on the upper neck and lowerhalf of the type SS-1 rope sockets. These units are availablefor various wire rope sizes.

Rope SocketsCompleteAssembly

Tubing Size Rope FishingNeck Size

Thread Size Components

RS109696 1”

1/2” - 5/8”

.700” 9/16” - 12 N.C. 1 ea: RS109600 .8125” x 9/16” BOTTOM1 ea: RS100096 .8125” TOP, 9/16” WIRELINE

SS1158581-1/4” to 1 3/4” 1.000”

5/8” API SuckerRod Thread

1 ea: SS115800 1-1/4” x 5/8” BOTTOM1 ea: SS110058 1-1/4” TOP, 5/8” WIRELINE

SS115896 5/8” API SuckerRod Thread


SS1358581-1/2” to 2-1/2” 1.188”





RS155896 1-1/2” 1.125” 5/8” API SuckerRod Thread

1 ea: RS155800 1-1/2” x 5/8” BOTTOM1 ea: RS150096 1-1/2” TOP, 9/16” WIRELINE

SS173412

2” to 3” 1.375”


1 ea: SS173400 2” x 3/4” BOTTOM1 ea: SS170012 2” TOP, 1/2” WIRELINE


1 ea: SS173400 2” x 3/4” BOTTOM1 ea: SS170058 2” x 5/8” WIRELINE


1 ea: SS173400 2” x 3/4” BOTTOM1 ea: SS170096 2” TOP, 9/16” WIRELINE

Rope Socket

OS-GA Bushing Assembly forGuiberson Type H Oil Saver Rubbers

Part # Type SizeGA-9/16 Type H - Black 0 - 5/16”

3/8” - 5/8”3/4” - 1”

GA-9/16-G Type H - GreenGA-9/16-M Guiberson “H” (Med) GA-9/16-S Guiberson “H” (Soft)

O-GA Guiberson “H” Seal KitOSB-C Bell “HR” & Bowen 3/8” - 5/8”OSBJ BJ Stipple 1/2” - 7/8”

OSBJ-1/4” BJ Stipple 1/4” - 5/8”OSB-1 Bell Type “HL” 3/8” - 5/8”

Oil Saver Rubbers - Tough, Long-Life RubberOil States Oil Saver Rubbers are molded from a specialcompound of oil, gas and abrasion-resistant rubber for longservice life. Oil and other fluids are removed from thewireline and allowed to re-enter the well, which helps preventpotential well-site contamination.

OSBJ Wireline Wiper

Type GA OSB-1 OSB-C

Rod Stripper Rubbers, Pipe Wipers


Pipe WipersConvenient Cutting GroovesMolded into Oil States long wearing, abrasion-resistant Pipe Wipers are concentric grooveswhich act as a guide for cutting the wiper intovarious pipe sizes.

Keeps Out Foreign ObjectsPipe Wipers can also prevent foreign objectsfrom entering the well bore by covering theannulus between the tubing and the casing.

WiperSize

Tubing Size

9”

1 1/4”-2 1/16”2 3/8”2 7/8”3 1/2”

10”2 3/8”

2 7/8”-4 1/2”

12”

1 1/4”-2 1/16”2 3/8”2 7/8”3 1/2”

4”-4 1/2”

14”

2 3/8”

2 7/8”

3 1/2”-5”

17”2 3/8”

2 7/8”-5”

Cutting Grooves

Molded to fit1 1/4” - 3 1/2” tubing

sizes

Molded to fit2 3/8” tubing, or may

be cut to fit largersizes

Molded to fit1 1/4” - 3 1/2” tubing,or may be cut to fit

larger sizes

Molded to fit2 3/8” & 2 7/8” tubing,

or may be cut to fitlarger sizes

Molded to fit 2 3/8”tubing, or may be cut

to fit larger sizes

PartNumber

9SRL-19009SRL-23759SRL-28759SRL-3500

10-HB-2375

10-HB-XXXX

12SRL-190012SRL-237512SRL-287512SRL-350012SRL-XXXX14SRL-2375

14SRL-2875

14SRL-XXXX

17TL-2375

17TL-XXXX

Rod Stripper Rubbers -Excellent Service LifeRod Stripper Rubbers efficiently remove oil andother fluids from the rod string being pulled fromthe well. The special abrasion and wear-resistant rubber compound used in the stripperrubbers assures maximum product service life.

Part Number Type SizeBRS-FINGER E.E. Stripper 5/8” - 1”

RS-5350 E.E. Stripper All Rod SizesRS-5058 BJ Praetet 5/8” RodRS-5034 BJ Praetet 3/4” RodRS-5078 BJ Praetet 7/8” RodRS-5100 BJ Praetet 1” RodRS-Pigtail BJ “Pigtail” All Rod Sizes

“BRS” RodStripper Rubber

10” Handlebar Type

BJ “Praetet”

RS-5350

BJ “Pigtail”

Type SRL, 9-SRL12-SRL & 14-SRL

Thin Lip, Type TL

Tubing Stripper Rubbers


Hercules Type

NH type 4 in 1 Petromec “Flex Grip”

OCT Type ROS OCT Type T-16 ROS

PartNumber

Description NominalSize

Guiberson TypeDH-1315

Guiberson Type

1.315

DH-1660 1.660

DH-1900 1.900

DH-2250 2-3/8

DH-2750 2-7/8

DH-3000* 2.875 DP

DH-3750* 3.500

BIW-1 TypeBIW-1-20*

BIW PX-107

2-3/8

BIW-1-25* 2-7/8

BIW-1-30* 3-1/2

Gulfco TypeGSR-12*

Gulfco Type S6

1.660

GSR-15* 1.900

GSR-17* 1.990

GSR-20* 2-3/8

GSR-25* 2-7/8

Huber TypeHERC-20*

Huber Hercules2-3/8

HERC-25* 2-7/8

Norris-Hinderliter TypeNH-12*

Norris-Hinderliter 4-1

1.660

NH-15* 1.900

NH-20* 2-3/8

NH-25* 2-7/8

Petromec TypePETRO-20

Petromec “Flex Grip” 20155-32-3/8

PETRO-25 2-7/8

OCT TypeROS-20*

OCT Type

2-3/8

ROS-25* 2-7/8

ROS-30* 3-1/2

RT-1617*

T-16 OCT Type

2.063

RT-1620* 2-3/8

RT-1625* 2-7/8

RT-1630* 3-1/2

Guiberson Type BIW PX-107

Gulfco Type S6, GSR

A product of Oil States for more than thirty years. Tubing Stripper Rubbers are

made from a proven oil and abrasion-resistant rubber.

Tubing can be pulled or run-in with pressure still on the well while also stripping

fluids off the tubing O.D. to provide a cleaner job site.

*Available by special order

Tubing Stripper Rubbers


LarkinTop Seal

PGSR Type

Part Number Head Type SizePGSR

PGSR-12*

PGSR Type

1.660PGSR-15* 1.990PGSR-20* 2-3/8PGSR-25* 2-7/8PGSR-30* 3-1/2

Halstrip TypeHS-10* TXS-10, Halstrip 1.315HS-12* TXS-12, Halstrip 1.660HS-15* TXS-15, Halstrip 1.900HS-17* TXS-17, Halstrip 2-1/16HS-20 TXS-20, Halstrip 2-3/8HS-25 TXS-25, Halstrip 2-7/8HS-30* TXS-30, Halstrip 3-1/2

Rector TypeRSR-10*

Rector ‘S’

1.315RSR-12* 1.660RSR-15* 1.900RSR-20* 2-3/8RSR-25* 2-7/8RSR-30* 3-1/2

Larkin TypeLSK-20

Larkin ‘K’

2-3/8LSK-25 2-7/8LSK-30* 3-1/2

LSK-TS-20 2-3/8LSK-TS-25 2-7/8

LSR-12

Larkin ‘SR’

1.660LSR-15 1.900LSR-20 2-3/8LSR-25* 2-7/8LSR-30* 3-1/2

Tubing Stripper Top SealLSR-TS-20*

4-1 & Larkin ‘SR’2-3/8

LSR-TS-25* 2-7/8LSR-TS-30* 3-1/2

Marcom TypeMSR-20* Marcom 2-3/8

Halstrip

Larkin Type SR

Larkin Type K

*Available by special order.

RSR Type

Tubing Test Cups


Bar Type CupsPart Number Tubing O.D. Tubing Weight Tool Size Durometer

150BT-2.90* 1.900” 2.90 1”

90216BT-3.25* 2 1/16” 3.25-3.4 1”

238BT-0890

2 3/8”4.6-4.7

7/8”

238BT-1070*

1 1/16”

70

238BT-1080* 80

238BT-1090 90

238BT-1091* 91

238BT-1270

1 1/4”

70

238BT-1280 80

238BT-1290 90

238BT-1291* 91

238BT-5.95* 5.95 90

278BT-1070*

2 7/8”

6.4-6.5

1 1/16”70

278BT-1090 90

278BT-1270*

1 1/4”

70

278BT-1280* 80

278BT-1290* 90

278BT-1291* 91

278BT-1370*

1 5/16”

70

278BT-1370* 70

278BT-1380* 80

278BT-1390 90

278BT-1570*

1 1/2”

70

278BT-1580* 80

278BT-1590 90

278BT-1670

1.600”

70

278BT-1680* 80

278BT-1690 90

278BT-1691* 91

278BT-7.90* 7.90 90

278BT-870* 8.70 90

350BT-1270*

3 1/2”

9.2-9.3

1 1/4”70

350BT-1290* 90

350BT-1670*1.600”

70

350BT-1690* 90

350BT-1870*

1.875”

70

350BT-1880* 80

350BT-1890* 90

350BT-2070*

2.000”

70

350BT-2080* 80

350BT-2090* 90

350BT-10.3* 10.31.855”

90

350BT-12.95

12.95

90

350BT-12.95-1670 1.600”

70

350BT-12.95-1690 90

450BT-2870

4 1/2” 9.5-11.6 2.875”

70

450BT-2880 80

450BT-2890 90

*Available Special Order Only

Drag TypeThe standard drag-type test cup is constructed

of a 70 durometer upper section with a 90

durometer lower section for greater strength.

The two compounds are bonded to a steel

sleeve and base to form a rugged, long lasting

test cup.

Bar TypeOil States bar-type tubing test cups are

available for six tubing sizes, various tool sizes

and in 70, 80 and 90 durometer nitrite rubber

compounds. A 90 durometer natural rubber

compound is also available for all-weather

operation. Field tests have repeatedly proven

the heavy-duty capabilities of this cup.

Drag Type CupsPart Number Tubing O.D. Tool Size

20-MT 2 3/8”7/8”

20-MTS 2 3/8” Hydril

25-TC 2 7/8” 1 1/16”

30-TC 3 1/2” 1 1/4”

Drag Type

Water Saver Cup

Bar TypeWater Saver Cups

Part Number Tubing O.D. Cup I.D.20-WS 2 3/8”

11/16”

25-WS 2 7/8”

30-WS 3 1/2”

20-WS-60 2 3/8”

25-WS-60 2 7/8”

30-WS-60 3 1/2”

OSI Sucker Rod Guides


Sucker Rod GuidesIncrease Pumping EfficiencyEliminate or greatly reduce down-hole problemswith Oil States’ Hi-Temp Snap-on and Twist-onRod Guides. With a coefficient of friction whenwet lower than metal, overall pumping efficiencyis increased while costly metal-to-metal contactbetween the rods and tubing is minimized. Wearon couplings is also less, thus reducing costly rodpartings.

Fewer “Pulling” JobsThe guides also function as bearings bycentralizing the sucker rods in the tubing. Evenas tubing buckles in the well during the upstroke,the guides help prevent contact between the rodsand tubing. Polished rod loads are reduced dueto the lower friction and less abrupt stressreversals.

Snap-on GuidesThe standard of the industry for years, Oil States’Hi-Temp Snap-on guides are made of abrasion-resistant, synthetic rubber. A spring steel “clip”insert is molded into the rubber guide, providing apositive grip on the sucker rod and preventingslippage in temperatures up to 300°F.

Twist-on GuidesOil States’ Twist-on rod guides contain no metalclip insert. Tests, however, indicate an excellentholding strength due to design and materials.The Twist-on style rod guide can easily beinstalled with a pipe wrench, and withstandtemperatures up to 200°F.

Rubber Rod GuidesPart

NumberSize Rod Size Tubing

Size5820-HT 5/8” X 2” 5/8”

2 3/8”3420-HT 3/4” X 2” 3/4”7820-HT 7/8” X 2” 7/8”5825-HT 5/8” X 2 1/2” 5/8”

2 7/8”

3425-HT 3/4” X 2 1/2” 3/4”7825-HT 7/8” X 2 1/2” 7/8”1025-HT 1” X 2 1/2” 1”1125-HT* 1 1/16” X 2 1/2” 3/4” Pipe1525-HT* 1 5/16” X 2 1/2” 1” Pipe5827-HT* 5/8” X 3” 5/8”

3 1/2”

3427-HT 3/4” X 3” 3/4”7827-HT 7/8” X 3” 7/8”1027-HT 1” X 3” 1”1127-HT* 1 1/16 X 3” 3/4” Pipe1527-HT* 1 5/16” X 3” 1” Pipe3435-HT* 3/4” X 3 1/2” 3/4”

Casing7835-HT* 7/8” X 3 1/2” 7/8”1035-HT* 1” X 3 1/2” 1”1135-HT* 1 1/16” X 3 1/2” 3/4” Pipe1535-HT* 1 5/16” X 3 1/2” 1” Pipe

Twist On GuidesPart

NumberSize O.D. of

Guides(Installed)

TubingSize

TO-3420 3/4” Rod X 2” Tubing1 3/4” 2 3/8”TO-5820 5/8” Rod X 2” Tubing

TO-7820 7/8” Rod X 2” TubingTO-3425 3/4” Rod X 2 1/2” Tubing

2 1/8” 2 7/8”TO-7825 7/8” Rod X 2 1/2” Tubing

Rod coupling shows abrasivedamage of metal-to-metal friction.Sucker Rod Guides

*Available by special order.

All dimensions shown arenominal only and subject to

change without notice

A B C D E2.01 1.88 1.28 1.09 0.872.46 2.29 1.67 1.34 1.25

3.19

2.91

1.75 1.34 1.302.31 1.94 1.22

3.05 1.75 1.34 1.313.01 2.21 1.94 1.243.05 1.75 1.34 1.313.01 2.21 1.94 1.243.58 3.53 2.62

1.941.31

3.51 3.43 2.253.41 3.20 2.60 1.29

4.18 3.902.66 2.41

1.46

3.93 3.72 1.514.52 4.37 2.66

2.411.46

4.52 4.37 2.664.37 4.15 2.67

1.394.37 4.15 2.67

5.10 4.91

3.28 2.90 1.445.01 4.83

4.95 4.64

5.65 5.41 3.52 2.90 1.46

6.12 5.91 4.18 3.53 1.43

6.00

5.70 4.06 3.531.38

5.604.23 4.034.18 2.90 1.43

5.70 4.06 3.531.38

5.604.23 4.034.18 2.90 1.43

PartNumber

P-204-1P-254-1*P-304-2

*P-304-S-1P-304-1P-304-SP-304-1P-304-SP-354-1P-404-1*P-404-2

P-454-1

*P-454-DP

P-504-1

P-504-2

P-554-1

P-554-2

P-554-2A

*P-604-1

P-658-2P-658-3

*P-658-3A*P-658-3CP-658-3

*P-658-3A*P-658-3C

�

�

�

�

�

OSI Packer Cups


Packer CupsOil States packer cups are molded from adurable oil, gas and abrasion resistant rubbercompound that withstands wear and tear, evenunder high pressure. Each is equipped with asturdy steel base for additional support in thecritical area where the wires connect to thecup base. Oil States offers over fifty individualcups, ranging from 2 3/8” tubing thru 13 3/8”casing, with optional I.D. sizes from manypopular casing sizes.

*Special compounds are available on request. High pressurecups are also available on certain sizes.

NominalTubing/Casing

O.D.

Wt.RangeLb/Ft

Tubing/Casing

I.D.

2 3/8” 4.6-4.7 1.9952 7/8” 6.4-6.5 2.441

3 1/2”

7.7 3.068

9.2-9.32.992

10.2

4”9.5 3.54811.0 3.47613.4 3.340

4 1/2”9.5 4.09011.6 4.00016.6 3.826

5”

13.0 4.49415.0 4.40818.0 4.27620.3 4.184

5 1/2”

13.0 5.04415.0 5.01215.5 4.950

17.0 4.892

20.0 4.77823.0 4.670

6”15.0 5.52418.0 5.424

6 5/8”

20.0 6.049

24.0 5.921

28.0 5.791

*Available special order only.

2 3/8” - 6 5/8” Cups

PartNumber

P-958-2*P-958-2AP-958-2BP-958-2

*P-958-2AP-958-2B*P-958-4

*P-958-4BP-958-1AP-958-1

P-958-1B*P-958-4

*P-958-4BP-958-1AP-958-1

P-958-1B*P-958-4

*P-958-4BP-958-1AP-958-1

P-958-1B*P-958-3P-958-3AP-958-3B*P-958-3P-958-3AP-958-3B P-1075

P-1075-BP-1075

P-1075-B P-1075-AP-1075-AP-1175-1

*P-1175-1BP-1175-1

*P-1175-1B*P-1200

*P-1200-BP-1338-1P-1338-1



A B C D E6.60 6.39 4.06 3.53 1.386.57 6.30 4.21 2.90 1.446.60 6.39

4.063.53 1.38

6.57 6.30 2.90 1.446.52 6.27 3.53 1.386.50 6.22 4.45 4.03 1.446.52 6.27 4.06

3.53 1.386.22 4.45 4.03

6.34 6.09

4.064.19 4.03 1.40

4.062.90

1.383.53

4.19 4.03 1.404.06 2.90 1.38

6.12 5.91 4.183.53

1.43

6.005.70 4.06

1.385.60

4.23 4.034.18 2.90 1.43

7.156.92 4.61

3.53

2.047.15

6.90 6.744.63

2.00

6.73 6.51 1.96

8.24 8.02 5.043.53

1.574.53

8.03 7.67

5.30

1.56

5.75 5.53

5.303.534.53

5.75 5.535.30 3.53

7.76 7.49 5.35

4.533.534.533.53

PartNumber

P-704-1*P-704-1C P-704-1

*P-704-1C P-704-1A*P-704-1BP-704-1A*P-704-1BP-704-2

*P-704-2A*P-704-2CP-704-2

*P-704-2A*P-704-2C

P-658-2

P-658-3*P-658-3A*P-658-3C

P-758-1

P-758-2

*P-758-3P-904-1

*P-904-1BP-858-1

*P-858-1AP-858-1BP-858-1

*P-858-1AP-858-1B*P-858-2

*P-858-2B*P-858-2

*P-858-2B

OSI Packer Cups



O.D.

Wt.RangeLb/Ft

Tubing/Casing

I.D.

7”

17.0 6.538

20.0 6.456

22.0 6.398

24.0 6.336

26.0 6.276

29.0 6.184

32.0 6.09435.0 6.004

38.0 5.920

7 5/8”

24.0 7.02526.4 6.96929.7 6.87533.7 6.76539.0 6.625

8 5/8”

20.0 8.191

28.0 8.017

36.0 7.825

40.0 7.725

44.0 7.625



O.D.

Wt.RangeLb/Ft

Tubing/

CasingI.D.

9 5/8”

29.3 9.063

36.0 8.921

40.0 8.835

43.5 8.755

47.0 8.681

53.5 8.535

10 3/4”

40.5 10.050

55.5 9.760

60.7 9.66073.2 9.406

11 3/4”38.0 11.150

54.0 10.880

12” 40.0 11.384

13 3/8”54.5 12.61572.0 12.347



A B C D E9.21

8.67

5.02 3.53 1.77

9.23 5.775.53

1.624.53

9.21 5.02 3.53 1.77

9.23 5.775.53

1.624.53

9.03 8.60 5.795.53

1.643.53

8.90 8.45 5.035.53

1.814.53 3.53

9.03 8.60 5.795.53

1.643.53

8.90 8.45 5.035.53

1.814.53 3.53

9.03 8.60 5.79 4.53

1.64 5.53

8.90 8.45 5.035.53

1.814.533.53

8.80 8.42 5.805.53

1.644.533.53

8.80 8.42 5.805.53

1.64 4.533.53

10.17 9.715.83

4.53

1.64

3.534.533.53

9.85 9.30 4.53

11.25 10.50

6.12 4.53 1.655.95 3.53 1.716.12 4.53 1.655.95 3.53 1.71

11.82 11.387.22

4.531.69

11.38 10.38 3.53

12.68 12.29 7.10 4.53 1.72


�

�

�

�

�

7” - 8 5/8” Cups

9 5/8” - 13 3/8” Cups

Locations


For over 60 years, Oil States has provided a wide array ofelastomeric and plastic products for the oil & gas, defense,

construction and general industries. Oil States maintains a highlevel of technical competency in engineering, development andmanufacturing. Oil States swab cups and packer elements are

molded from a variety of custom elastomers and meet the mostdemanding quality requirements in the industry. Oil States

Industries, Inc. has representatives carrying the Oil States andRegal product lines at the following locations:

CaliforniaLong Beach, CABakersfield, CAVentura, CATaft, CA

ColoradoGreeley, CO

IllinoisOlney, IL

KansasGreat Bend, KS

LouisianaBossier City, LAHouma, LALafayette, LA

MississippiNatchez, MSLaurel, MS

New MexicoFarmington, NMHobbs, NM

North DakotaWilliston, ND

OhioWooster, OH

OklahomaChoctaw, OKOklahoma City, OK

TexasAbilene, TXAlice, TXDecatur, TXHouston, TXKilgore, TXOdessa, TXVictoria, TX

UtahVernal, UT

WyomingCasper, WYGillette, WYRock Springs, WY

CanadaNisku, Alberta

Please call our Arlington Corporate Office forinformation concerning foreign agents and/or

stocking locations.

Proprietary Oilfield ProductsCorporate OfficeP.O. Box 670Arlington, Texas 76004Telephone: 817-548-4200Fax: 817-548-4252

Terms and Conditions of Sale

Effective December 1, 2012

Oil States Industries, Proprietary Oilfield Products, is hereafter referred to simply as Oil States.

Warranty

All Oil States products are guaranteed to be free from defects in both workmanship and materials for a period of one yearfrom date of purchase under recommended use or service. This guarantee and the liability of Oil States, however, is limited

solely to the replacement of defective parts or refund of purchase price.

Payment Terms

Net 30 Days with Approved Credit, else Payment in Advance of shipping. Master Card and Visa are accepted.

Freight Allowance

FOB Point of Shipment, Ex-works.

Export Sales

Export sales will be made only through the Proprietary Sales Department, Oil States Industries, Inc, Arlington, Texas

Pricing Policy

1. The schedule of discounts and terms and conditions of sales cannot be altered without written approval of the ProprietarySales Department, Oil States, Arlington, Texas.

2. Minimum charge on all sales, excluding discounts, labor, freight, and other service charges will be $75.00.

3. All published catalog list price and discount schedules are subject to change without notice.

4. All items classified as “Available by Special Order” are not carried in warehouse stock; delivery might exceed thatnormally experienced. A Minimum Order of $500.00 net per line item may be charged on “Special Order” items. Sales onthese items are final, and cannot be returned for credit. Contact the Proprietary Sales Department for details on“Special Order” items.

Return Goods

1. Permission must be secured from Oil States prior to return of any merchandise.

2. List of material submitted for return must show date of purchase and invoice number.

3. All return merchandise is subject to inspection by Oil States and must consist of items being actively offered for sale by OilStates.

4. A restocking charge of 15% will be made on all merchandise returned within 90 days after date of purchase. A restockingcharge of 25% will be made on merchandise returned after 90 days. Freight must be prepaid by shipper on all returnedgoods.

5. Credit will be allowed only on merchandise returned within one year of purchase date.

6. Refunds on returned merchandise will be issued in cash or in merchandise credit. Merchandise refunds in form of creditcan be applied against future purchases from Oil States, but in no case to exceed fifty percent of any one month’s purchase.

Terms and Conditions of Sale

OIL STATES SYSTEMS & SOLUTIONSProduction Platform SystemsIntegrated Solutions for Secure Production

Riser Systems & Conductor SolutionsComplete Risers with Advanced Merlin™ Connection Technology

Subsea Pipeline SystemsRobust Connections & Sealing Technology

Onshore, Marine & Industrial SolutionsLeading Technologies for Maximum Well Productivity & Safe Operations

ServicesWe Work Where You Work, Around the World, Around the Clock

Copyright 2018 Oil States Industries, Inc. All rights reserved. Oil States is a registered trademark of Oil States International, Inc. DM\r8-18\M

™

OIL STATES INDUSTRIESWell Servicing EquipmentCustom Molded ProductsManufacturing, Engineering & Sales1720 Central Texas ExpresswayLampasas, Texas 76550 USAT 512 556 5471

7701 S. Cooper StreetArlington, Texas 76001 USAT 817 548 4200

www.oilstates.com

About Oil States Industries

Oil States Industries, a subsidiary of Oil States International (NYSE: OIS), is a major global provider of integrated energy systems and solutions. With over 75 years serving customers with innovative technology and technical expertise, we deliver reliable, cost-effective solutions for offshore drilling, completion/workover, production, lifting and mooring challenges. We also serve customers in the onshore, marine and industrial markets. Oil States is headquartered in Arlington, Texas USA with locations in 14 countries and more than 1,700 employees. For additional information, visit www.oilstates.com.

[email protected] [email protected]

WELL SERVICING & PRODUCTION EQUIPMENToilstates.com/wp-content/uploads/Oil-States-Well...suspended in...

Documents

Transcript of WELL SERVICING & PRODUCTION EQUIPMENToilstates.com/wp-content/uploads/Oil-States-Well...suspended in...