Welding
description
Transcript of Welding
Welding
LEMMONS
Arc Welding – fusing two or more pieces of metal together using heat from an electric arc
Advantages of Arc Welding
• Quick repairs
• Cheap to operate
• Arc welder has other uses(cutting, gouging, beveling)
Types of Welding Machines
I. ARC WELDERA. AC Welder• SMAW(Shielded
Metal Arc Welding)• Plugs into any 240
volt outlet• Uses AC current• Runs up to 225 amps
1. Advantages
– Low cost
– Easy to maintain
Flow
– 50% heat at electrode
– 50 % heat at work
B. DC Reverse Current (DC+)• Deeper penetration• Higher possible amps
• 2/3rd heat at work
• 1/3rd heat at electrode
C. DC Straight Current (DC-)
• Shallow penetration
• Lower amps
• Flatter bead
• 2/3rd heat at electrode
• 1/3rd heat at work
AC/DC Welders
• Combines all three processes into one machine
Gasoline Driven Machines
• AC/DC welding machine powered by a gas or diesel engine
• Portable
• AC generator power to run other tools
II. MIG(Metallic Inert Gas)
1. Other names
• hardwire, short arc, GMAW(Gas Metal Arc Welding), wire machine
* Advantages
• Can be used as an automatic welder
• Can use flux core wire to eliminate gas
• No slag
• Continuous weld
III. TIG(Tungsten Inert Gas)
1. Other Names• GTAW(Gas Tungsten Arc Welding)
Heliarc
* Advantages• Welds are free of slag• Produces the strongest weld• No splatter• Almost all metals can be welded with the
TIG process• Produce non corrosive welds
Selecting a Welder* Factors to consider:• Cost• Use• Select a reliable manufacturer
(Lincoln, Miller, ESAB)• Guarantee or warranty (90 Days, 1 yr,
etc.)• Service
* Other equipment needed• Welding hood• Assure proper electrical hookup• Pliers• Leather gloves• Chipping hammer• Wire brush• Grinder• Metal Table
Electrodes
A. Definitionwire, either bare or with flux, used in the welding process
B. Types of Electrodes1. Coated – electrode metal should match base metal. Covered with powder flux.
2. Bare- requires excessive heat and is voltage sensitive. It is
smoke free.
3. Carbon – special purpose rod for high carbon steel
C. Electrode Classification
1. Universal color code and number system
Example: E7018
E - electrode
70 - tensile strength in thousands pounds
1 } welding position
1 = all position
2 = flat and horizontal
3 = flat only
Example: E7018
8 }current, penetration, flux, etc.
numbers range 0 - 8
D. Electrode Size
Size is determined by the diameter of the bare end of the electrode
Examples:3/32” electrode
• 36 rods per pound• Run at 30-80 amps
1/8” electrode• 17 rods per pound• run at 70-120 amps
5/32” electrode• 11 rods per pound• Run at 120-170 amps
E. Common Electrodes
6010 – mild steel , DC+ deep penetration
6011 – same as 6010, AC/DC
6013 – AC/DC, quiet, general purpose
7018 – AC/DC+, high carbon steel, iron powder flux
Selecting an Electrode• ID of base metal
• Available current
• Metal thickness
• Joint design
• Welding position
• Environmental conditions
• Storage
• Building Code
8 Essentials to a Proper Weld• Proper electrode• Metal preparation• Proper amperage• Proper electrode angle• Proper arc length• Correct travel speed• Proper curing of finished weld• Good connected ground
I. Preparing Metal for Welding
a. Metal should be cleaned
b. Dirty metal is harder to weld and requires more heat
c. Clean metal by brushing, filing, sanding, grinding, scraping, sandblasting, chemically
d. Metal more than ¼” thick metal should be beveled at 30 degrees and spaced 1/16” apart
e. Bevels – one-sided, two-sided, lap, corner
II. Amperagea. Too high
• Flat bead• Splatter on bead edge• Undercut edges• Extremely loud
b. Too low• high, narrow bead• Weak penetration• Hard to keep arc goingc. Correct• Even, steady sound• Adequate penetration• Uniform in shape
III. Electrode Angle
A. Flat welds – electrode angle should be 15 degrees to the direction of travel and 90 degrees to each side
B. Vertical welds – electrode angle should be on the centerline and angled 30 degrees down
IV. Arc Length
• The distance between the electrode and work
• Arc length should equal the diameter of the bare end of the electrode
V. Travel Speed
• How fast or slow the electrode moves across the work
• The bead should remain the same width and height at all times
• Watch the molten puddle to gauge travel speed
Methods of Starting an Arc
1. Scratching - simply drag the electrode across the work, lifting it when arc starts
2. Tapping – tap the electrode to the work, picking it up quickly while maintaining the arc
Causes of difficulty starting an arc
1. Flux chipped off end of electrode
2. Flux covering end of electrode
3. Improper amperage(too low)
4. Inadequate ground
Electrode movement or patterns
1. Slight arch2. Straight3. Circular4. Zig Zag5. Horseshoe