Welcome to Practical Components · 2006. 3. 3. · LQFP Low Profile Quad Flat Pack ..... 21 QFN...

Practical Components is a distributor of mechanical IC

samples or “dummy” components and also distributes

SMD production tools and equipment.

Welcome toPractical Components

What other products doesPractical Components offer?There are a number of solder training aids, tools,

and equipment that Practical Components carries. The catalog has

the latest information regarding available products. In addition,

your sales representative can supply technical information and

pricing on these products.

Who uses dummy components?Companies that are involved with electronic

component assembly, testing, evaluation and employee training.

Contacting Practical Components.If you should have any additional questions concerning Practical

Components, our products or policies, we offer a number of

different ways to contact us:

Practical Components, Inc.15211 Springdale StreetHuntington Beach, CA 92649Tel: 1-714-899-8309Fax: [email protected]

What are dummy components?Dummy components are the exact mechanical equivalent of

functional electronic components.

Why use dummy components?Dummies save money. In cases where only mechanical character-

istics are required, dummy components can be used instead of

live functioning components. Because there is not an expensive

die inside the package, the cost for performing mechanical testing

is significantly lower.

Who is Practical Components?A team of dedicated electronic industry professionals makes up

Practical Components, offering value pricing, on-time delivery, and

superior service to customers. The Practical Components team is

ready to provide project assistance in the areas of technical

component knowledge, drawings, component land patterns, and

PCB practice kits.

What is a PCB Practice Kit?Combining both the PCB Practice Board and dummy components

allows customers to conduct assembly process evaluation without

using high-cost live components and functional PC Boards. Kits

are available in a single pack, for employee hand soldering

training, or packaged for production equipment evaluation. Both

XY Theta data and Gerber data are available without charge.

Frequently Asked Questions

Patricia Meeks

Open the bookmarks window for easy navigation through this catalog.

Patricia Meeks

Click here to jump to the Table of Contents.

Patricia Meeks

Patricia Meeks

Patricia Meeks

Non-Catalog Items: Merchandise not listed in our catalog, if

available from our suppliers, may be subject to minimum order

quantities and/or special handling charges. Shipment is made as

quickly as deliveries are received from our suppliers. Special order

products are sold on a non-returnable basis.

Quotations: All items are subject to prior sale.

Dishonored Check Policy: If a check you give us as payment is

dishonored for any reason by the bank or any other institution on

which it is drawn, you agree to pay us $20.00 as a service charge.

In addition, you agree to pay any other reasonable charges

imposed by any check verification company or collection agency

that we may use for collection.

Prices/Quantities: Prices are subject to change without notice and

quantities may be limited.

Handling Charge: A $10.00 handling charge applies to all orders

less than $50.00.

Terms: We accept Visa, MasterCard and American Express

(minimum order is $50.00).

Open Account: We bill on a net 30-day basis to customers with

approved credit.

Large Quantity Quotations: Practical Components will be happy

to quote quantities in excess of the amounts shown in the catalog.

Freight Charges: On open accounts, actual freight charges are

added to the invoice. A packing and handling fee of $4.50 is added

to the order. C.O.D accounts will have the freight charges pre-

billed to the C.O.D. total in addition to a $4.50 packing and

handling charge.

Special Requirements: Please include specific instructions if you

require special packing, marking, shipping, routing or insurance.

*All prices are in US$.

How To Place Your Order

Our sales staff is ready to serve you from 7:30 A.M. to

5 P.M. Pacific Standard Time, Monday through Friday.

Our fax lines are open 24 hours every day.

Fax and email orders received after normal busi-

ness hours are processed the next business day.

Please include your telephone number so we can

confirm your order.

Terms and Conditions

Out Of Stock Items: Items not available for immediate shipment

will be shipped as they become available. Items not available at

the end of 90 days will be cancelled. The number of back-ordered

days may be extended beyond 90 days with customer approval.

Return Policy: Returns must be made promptly and accompanied

by a return authorization number. Please contact a customer

service representative to obtain a return authorization number. All

returns must be made within 30 days of date of invoice and

accompanied by return authorization number.

� Return freight charges must be prepaid.

� C.O.D. returns cannot be accepted.

� Return merchandise in original packaging and in

resalable condition.

� Please note that items returned due to customer error may be

subject to a restocking charge of 25%.

� Non-catalog items are not returnable.

Catalog Listings: Not all products listed in this catalog are

maintained in stock, and all product specifications and prices for

each product are current as of the date of publication. Product

listings, specifications and prices for each product are subject to

change without notice.

Product Liability: Practical Components’ sole obligation for

products that prove to be defective within 10 days of purchase will

be replacement or refund. Practical Components gives no

warranty either expressed or implied and specifically disclaims all

other warranties, including warranties for merchantability

and fitness.

In no event shall Practical Components’ liability exceed the

buyer’s purchase price nor shall Practical Components be liable

for any indirect or consequential damages.

Shipment Damage: Merchandise is carefully packaged in

compliance with carrier requirements. Claims for loss or damage

in transit must be made with the carrier by the customer. All

shipments should be unpacked and inspected immediately upon

receipt. If damage does not become apparent until shipment is

unpacked, make a request for inspection by the carrier’s agent.

Failure to do so will result in the carrier refusing to honor

the claim.

Practical Components, Inc.15211 Springdale StreetHuntington Beach, CA 92649 USAPhone: 1-714-899-8309Fax: 1-714-899-8599Email: [email protected] Site: www.practicalcomponents.comF.O.B. Is Huntington Beach, CA USA

PRACTICALCOMPONENTS

Contents

Ball Grid ArrayPBGA Plastic Ball Grid Array ...................................................... 4CSBGA Chip Scale BGA Package ............................................. 7CBGA Ceramic Ball Grid Array ................................................... 8High Temperature FR4 CBGA Test Board .................................. 8BGA Variable Pitch and Array Board .......................................... 9µBall Grid Array ......................................................................... 10µBGA Test Boards ..................................................................... 14

Flip ChipFlip Chip .................................................................................... 15Flip Chip Test Boards ................................................................ 16

Plastic Quad Flat PackQFP Plastic Quad Flat Pack ...................................................... 18LQFP Low Profile Quad Flat Pack ............................................ 21QFN Quad Flat Pack Non-Leaded ............................................ 21BQFP Bumpered Quad Flat Pack ............................................. 22

Ceramic BodyCQFP Ceramic Quad Flat Pack ................................................ 23LCC Leadless Ceramic Carrier ................................................. 23

Small OutlineSOIC Small Outline Integrated Circuit ...................................... 24TSOP Thin Small Outline Package ........................................... 25SSOP Small Shrink Outline Package ....................................... 26TSSOP Thin Shrink Small Outline Package ............................. 28SON Small Outline Non-Leaded Package ............................... 29

Plastic Leaded Chip CarrierPLCC Plastic Leaded Chip Carrier ........................................... 30

Passives, Transistors, DiscretesSMT Surface Mount Transistors ............................................... 31SMC Surface Mount Ceramic Capacitors ................................ 32SMR Surface Mount Resistors .................................................. 33Zero Ohm Jumper Resistors .................................................... 34SMTA Surface Mount Tantalum Capacitor ............................... 34SME Surface Mount Electrolytic Capacitors ............................ 35Melf Diodes ............................................................................... 35

Through-HoleTO Through-Hole Transistors ................................................... 36Axial Leaded Resistors ............................................................. 36

Printed Circuit Board KitsCustom PCB Practice Kits ........................................................ 37PC008 Practice Board and Kits ................................................ 38PC008 Test Pattern ................................................................... 40SMTA Saber Evaluation PC Board and Kits ............................. 41PCB003 Solder Practice Board and Kit .................................... 42Omni Training Kits ..................................................................... 43

Through-Hole Training Kit, Through-Hole RecertificationKit, Standard Pitch Training Kit, Fine Pitch Training Kit

Omni Training ProductsWorkmanship Acceptance Posters .......................................... 44SMT Workmanship Criteria on CD-ROM .................................. 44Terminal Holder ......................................................................... 44Unified Inspection Criteria Workmanship Manuals .................. 45Unified Wiring and Soldering Handbook ................................. 45Soldering Workbook ................................................................. 45

Practical Production ToolsWeller QFP Lead Repair Kit ...................................................... 46Weller Reballing Kit ................................................................... 47Personal Magnifiers .................................................................. 48Adjustable Matrix Trays ............................................................. 49Practical Vacuum Handling Tools ............................................. 50

Practical Hand-Vac, Practical Pen-Vac, Practical Bulb-Vac,Practical SMD-Vac-GP, Practical Pac-Vac, Practical HP-300

Weller Soldering Gun Kit .......................................................... 52Weller Circuit Board Vise .......................................................... 52Weller Self-Contained 2-Person Fume Extractor ...................... 52Xcelite Pliers Kit—Electronics Handy Pack Assortment .......... 52Xcelite Attaché Tool Cases ....................................................... 53Xcelite Multi-Purpose Tool Kit ................................................... 54Xcelite Offset Ratchet Screwdriver Set ..................................... 54Xcelite Personal Computer Repair Kit ...................................... 54Eram Mutli-Purpose Assembly Kit ............................................ 54Eram Anti-Static 5-Tweezer and Micro-Cutter Kit ..................... 54

Tech Spray ProductsCleaners/Degreasers, Defluxers, Dusters, Freeze Spray ......... 55Static Control ............................................................................ 58Desoldering Braid ..................................................................... 59Equipment and Specialty Products .......................................... 60Swabs ....................................................................................... 60Wipes ........................................................................................ 61

Glossary .................................................................................... 62Fax Order Form ......................................................................... 63

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Patricia Meeks

Click on highlighted section heading to jump directly to that section.

4 Practical Components • Phone 1-714-899-8309 • Fax 1-714-899-8599 • [email protected] • www.practicalcomponents.com

Part Number I/O Count Pitch Body Size Ball Matrix Ball Alignment QuantityPer Tray

PBGA84-1.0mm-11mm 84 1.0mm 11mm — — 176PBGA144-1.0mm-13mm 144 1.0mm 13mm 12 x 12 Full Grid 160PBGA156-1.0mm-15mm 156 1.0mm 15mm 14 x 14 Perimeter 126PBGA160-1.0mm-15mm 160 1.0mm 15mm 14 x 14 Perimeter 126PBGA196-1.0mm-15mm 196 1.0mm 15mm 14 x 14 Perimeter 126PBGA208-1.0mm-17mm 208 1.0mm 17mm 16 x 16 Perimeter 90PBGA256-1.0mm-17mm 256 1.0mm 17mm 16 x 16 Full Grid 90PBGA288-1.0mm-23mm 288 1.0mm 23mm 22 x 22 Perimeter 60PBGA324-1.0mm-23mm 324 1.0mm 23mm 22 x 22 Perimeter 60

PBGA

PBGA144–1.0mm–13mmPlastic BallGrid Array

I/O Count

Body Size

Pitch

Add “T” to end of part number for Tray.Add “TR” to end of part number for Tape and Reel.

Part Number I/O Count Pitch Body Size Ball Matrix Ball Alignment QuantityPer Tray

PBGA121-1.27mm-15mm 121 1.27mm 15mm 11 x 11 Full Grid 126PBGA169-1.5mm-23mm 169 1.5mm 23mm 13 x 13 Full Grid 60PBGA225-1.5mm-27mm 225 1.5mm 27mm 15 x 15 Full Grid 40PBGA256-1.27mm-27mm 256 1.27mm 27mm 20 x 20 Perimeter 40PBGA272-1.27mm-27mm 272 1.27mm 27mm 20 x 20 Perimeter 40PBGA292-1.27mm-27mm 292 1.27mm 27mm 20 x 20 Perimeter 40PBGA313-1.27mm-35mm 313 1.27mm 35mm 25 x 25 Stagger 24PBGA324-1.27mm-27mm 324 1.27mm 27mm 20 x 20 Perimeter 40PBGA352-1.27mm-35mm 352 1.27mm 35mm 26 x 26 Perimeter 24PBGA388-1.27mm-35mm 388 1.27mm 35mm 26 x 26 Perimeter 24PBGA420-1.27mm-35mm 420 1.27mm 35mm 26 x 26 Perimeter 24PBGA480-1.27mm-35mm 480 1.27mm 35mm 26 x 26 Perimeter 24PBGA676-1.27mm-35mm 676 1.27mm 35mm 26 x 26 Full Grid 24

Plastic Ball Grid Array 1.0mm Pitch

Notes� Overall thickness of 1.0mm pitch PBGA packages will vary in

size (please call for more details).

� Parts are packaged in JEDEC trays.

� Call for tape and reel quantity and availability.

� Solder ball material is eutectic 63/67 SnPb.

� Some components are daisy-chained (please call for

more details).

� Daisy-chained connections are connections between I/O

(input/output) of the component.

Part Number System

Plastic Ball Grid Array 1.5mm/1.27mm Pitch

Notes� Parts are packaged in JEDEC-trays.


� Solder ball material is eutectic 63/67 SnPb.

� Solder ball diameter is 0.76mm (30 mils).

� Daisy-chain connections are connections between I/O

(input/output) of the component.

� Daisy-chain connections are used, paired with a PC board that

has complimentary connections between pads in order to test

for continuity. BGA packages should be baked at 125°C for 24

hours prior to assembly to prevent delamination during the

assembly process.

PBGA121–1.27mm–15mmPlastic BallGrid Array

I/O Count

Body Size

Pitch


� BGA packages should be baked at 125°C for 24 hours prior to

assembly to prevent delamination during the assembly process.

� Parts can be baked and dry-packed.

Part Number System

� Parts can be baked and dry-packed.

� Most PBGA packages are assembled with “dummy” die to

conduct thermal coefficient testing.

Practical Components • Phone 1-714-899-8309 • Fax 1-714-899-8599 • [email protected] • www.practicalcomponents.com 5

PBGA

PGBA225-1.5mm-27mm

PBGA169-1.5mm-23mm

PBGA256-1.27mm-27mm

8.00

18.0

023.00±0.20

23.0

0±0.

20

1.50

1.50

ø1.00(3X) Ref.

Pin #1 Corner

20.00 Ref.

20.0

0 R

ef.

3.00*45°(4X) B

A

0.20(4X)

Top View Die Side Bottom View Ball Side

A

B

C

E

D

F

G

H

J

L

M

K

N

A

B

C

E

D

F

G

H

J

L

M

K

N

123456789101112131 2 3 4 5 6 7 8 9 10 11 12 130.75±0.15ø

ø0.10ø0.30

S CC A BS S S

2.13±0.130.56 Ref. 0.60±0.10

0.97Ref.0.15 C

Seating PlaneC

30° Typ.

21.00

21.0

0

27.00±0.20

27.0

0±0.

20

1.50

1.50

ø1.00(3X) Ref.Pin #1 Corner

24.00 Ref.

24.0

0 R

ef.

4.00*45°(4X) B

A

0.20(4X)

0.75±0.15(225X)ø

ø0.10ø0.30

SS SS

CC A B

2.33±0.13

Seating PlaneC

0.56 Ref. 0.60±0.10

1.17 Ref. 30° Typ. 0.15 C


A

B

C

E

D

F

G

H

J

L

M

K

N

P

R

A

B

C

E

D

F

G

H

J

L

M

K

N

P

R

1234567891011121314151 2 3 4 5 6 7 8 9 10 11 12 13 14 15

24.13

24.1

3

27.00±0.20

27.0

0±0.

20

1.27

1.27


24.00 Ref.

24.0

0 R

ef.

4.00*45°(4X) B

A

0.20(4X)

0.75±0.15(256X)ø

ø0.10ø0.30

SS SS

CC A B


A

B

C

E

D

F

G

H

J

L

M

K

N

P

RT

U

W

Y

V

A

B

C

E

D

F

G

H

J

L

M

K

N

P

RT

U

W

Y

V

12345678910111213141516171819201 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Seating PlaneC

0.56 Ref. 0.60±0.10 2.33±0.13

1.17 Ref.30° Typ. 0.15 C


PBGA313-1.27mm-35mm

PBGA352-1.27mm-35mm

30.48

30.4

8

35.00±0.20

35.0

0±0.

20

2.54

2.54

1.27

1.27


30.00 Ref.

30.0

0 R

ef.

4.00*45°(4X) B

A

0.20(4X)

1 12 23 34 45 56 67 78 810 1011 1112 1213 1314 1415 1516 1617 1718 189 919 1920 2021 2122 2223 2324 2425 25

0.75±0.15(313X)ø

ø0.10ø0.30

SS SS

CC A B

A

BC

ED

F

G

H

J

L

M

P

T

U

W

Y

AAAB

AC

AD

AE

N

R

V

K

A

BC

ED

F

G

H

J

L

M

P

T

U

W

Y

AAAB

AC

AD

AE

N

R

V

K


Seating PlaneC0.56 Ref. 0.60±0.10 2.33±0.13

1.17 Ref. 30° Typ.

0.15 C0.15 C0.15 C

31.75

31.7

5

35.00±0.20

30.0

0±0.

20

1.27

1.27


30.00 Ref.

30.0

0 R

ef.

4.00*45°(4X) B

A

0.20(4X)

0.75±0.15(352X)ø

ø0.10ø0.30

SS SS

CC A B

Seating PlaneC0.56 Ref. 0.60±0.10 2.33±0.13

1.17 Ref. 30° Typ.0.15 C


AB

C

ED

FGHJ

LM

K

NPRTU

WY

V

AAABACADAEAF

AB

C

ED

FGHJ

LM

K

NPRTU

WY

V

AAABACADAEAF

123456789101112131415161718192023 22 212425261 2 3 4 5 6 7 8 9 10 1112 13 14 151617 18 19 20 232221 2425 26

PBGA


Part Number I/O Count Body Size Pitch Ball Matrix Ball Alignment

CSBGA20-5mm-1.0mm 20 5mm 1.0mm 6 x 6 PerimeterCSBGA28-5mm-.8mm 28 5mm .8mm 6 x 6 PerimeterCSBGA48-8mm-1.0mm 48 8mm 1.0mm 8 x 8 PerimeterCSBGA56-9mm-.8mm 56 9mm .8mm 10 x 10 PerimeterCSBGA72-9mm-.8mm 72 9mm .8mm 11 x 11 PerimeterCSBGA80-10mm-1.0mm 80 10mm 1.0mm 12 x 12 PerimeterCSBGA108-10mm-.8mm 108 10mm .8mm 11 x 11 PerimeterCSBGA96-12mm-1.0mm 96 12mm 1.0mm 14 x 14 PerimeterCSBGA120-13mm-1.0mm 120 13mm 1.0mm 13 x 13 PerimeterCSBGA156-13mm-.8mm 156 13mm .8mm 15 x 15 PerimeterCSBGA120-9x13mm-.8mm 120 9 x 13mm .8mm 9 x 14 Full Array

CSBGA20–5mm–1.0mmChip ScaleBGA Package

I/O Count Body Size

Pitch

Add “TR” to the end of part number for Tape and Reel.

Notes� Parts are packaged in waffle trays (tray quantity may vary).

� All CSBGA packages are daisy-chained.


� Package outline drawings and daisy-chain patterns are available

upon request.

CSBGA

Chip Scale BGA Package

Part Number System

A1 Corner

7.0 8.0

7.0

8.0 0.5 7.0

1 2 3 4 5 6 7 8A

B

C

E

F

G

H

D

0.6 Nom0.350.75

0.45 Nom

1.70 Max.

Top View (Die Side) Bottom View (Ball Side) X-Ray View (Daisy-Chain Pattern)

Side View

8 7 6 5 4 3 2 1A

B

C

E

F

G

H

D

1.0


CBGA

Practical Components now offers this high-temperatureFR4 CBGA board for placement and rework usingdaisy-chain CBGAs.Order the FR4 CBGA Test Board or configure custom kits to meet

your specific requirements.

Order Number: PCB006 (Board Only)

High Temperature FR4 CBGA Test Board

Part Number I/O Count Pitch Body Size Ball Matrix Ball Alignment

CBGA121-1.27mm-15mm 121 1.27mm 15mm 11 x 11 Full ArrayCBGA196-1.27mm-18.5mm 196 1.27mm 18.5mm 14 x 14 Full ArrayCBGA256-1.27mm-21mm 256 1.27mm 21mm 16 x 16 Full ArrayCBGA304-1.27mm-21x 25mm 304 1.27mm 21 x 25mm 16 x 19 Full ArrayCBGA361-1.27mm-25mm 361 1.27mm 25mm 19 x 19 Full ArrayCBGA625-1.27mm-32.5mm 625 1.27mm 32.5mm 25 x 25 Full Array

Ceramic Ball Grid Array

Notes� Parts are cavity up.

� Parts are packaged in non-JEDEC waffle trays

(tray quantity may vary).

� Parts are daisy-chained.

Part Number System

CBGA196–1.27mm–18.5mmCeramic BallGrid Array

I/O Count

Body Size

Pitch

Add “T” to the end of part number for Tray.

Not to scale—Top/bottom view (double-sided).

Actual size of board is 3.5" x 3.5".

CBGA Test Board

CBA121-1.27mm-15mm

CBA256-1.27mm-21mm

CBA361-1.27mm-25mm

CBA304-1.27mm-21x25mm

CBA625-1.27mm-32.5mm

P/N PC006 REV A

T1 T2

T2T1T1 T2

T2T1

T2T1

PH

ON

E:714.899.8309 Fax:714.899.8599

E-M

AIL

: klp

ci@

wor

ldne

t.att.

net

Notes� Kits can be configured to the customer’s requirements.

� All CBGA components are 1.27mm pitch.

� Gerber Data and X,Y Theta Data are available if required at

no charge.


1.27mm pitch 34x34

1.27mm pitch 26x26

1.27mm pitch 26x26

1.27mm pitch 34x34

1.5mm pitch 15x15

1.5mm pitch 15x15 1.5mm pitch 20x20 1.5mm pitch 20x20

Phone:714.899.8309 Fax: 714.899.8599

VARIABLE PITCH & ARRAY

E-m

ail:

dgpr

actic

al@

wor

ldne

t.att.

net

0.75mm pitch 6x8

1.00mm pitch 26x26

1.00mm pitch 26x26

0.8mm pitch 9x9

1.00mm pitch 11x11

0.8mm pitch 18x18

Phone:714.899.8309 Fax: 714.899.8599

VARIABLE PITCH & ARRAY

ww

w.p

ract

ical

com

pone

nts.

com

1.00mm pitch 11x11

0.5mm pitch 22x22

BGA Test Board

Variable Pitch and Array Board

Mix and match components to configure your custom kit.Practical Components is now offering a “one-of-a-kind” BGA

Variable Pitch and Array PC Board. Each board contains matrices

for the most popular ball pitches found on BGAs and CSPs. The

use of full matrices allows maximum flexibility for placing parts

with full, staggered, or perimeter configurations. Each board has a

mixture of even and odd matrices to enable placement, using

automatic equipment, of the highest ball counts available.


Top View Bottom View

Notes� Kits can be configured to the customer’s requirements.

� Gerber Data and X,Y Theta Data are available if required at

no charge.


Part Number I/O Count Pitch Body Size

TV-46A 46 .75mm 6 x 8mmTV-46AM 46 .75mm 6 x 8mmTV-62A 62 .75mm 9.3 x 11.5mmTV-62AM 62 .75mm 9.3 x 11.5mmTV-74A 74 .75mm 8.17 x 12.7mmTV-74AM 74 .75mm 8.17 x 12.7mm

Notes� Parts are packaged in waffle trays.

� Parts are eutectic (SnPb) solder bumps.

� Parts are daisy-chained.

� Parts are available on tape and reel.

Back View

(Nom) Z X

(Nom) Z X

A1 Corner

(5.51 Nominal Die)

Die 5

(7.47 Nominal Die)

Index Area

3

▲

Z 10

SeatingPlane

See Section Detail Side View(Scale=None)

▲

▲

Z

A

Die (0.432±0.025) thick

ø0.3±0.03

Lead

Adhesive

0.05 Z

0.84±0.05

Typical AssemblySection

Elastomer 7

Elastomer Seal4 Sides/Edges 7 11

Polyimide Tape ASM 6

0.18±0.03 9

10

ø0.1 Z XYø0.05 Z 9

ST

// 0.1 Z

7.87±0.05

4X — 0.05

▲

▲

Y

X

Bump View

Die Pad 1Datum Axis X

Die Pad 2

(2.505)

Datum Axis Y

(1.4)

(3.935)

5X 0.75

(2.505) (2.88)

0.375

5.76±0.05

6 5 4 3 2 1

4X r0.2 Max

A

B

C

F

G

H

7X 0.75(1.33)

A

®

TV

46 C

1

µB

GA

®

D

E

0.375

Notes:

1. Dimensioning and tolerancing per ASME Y14.5M–1994.

2. Do not subject part to ultrasonic cleaning or intense UV.

3. Mark back of die with laser.

4. Contact ball position designation per JESD 95–1, SPP –010(Bumps E3, E4 are missing).

5. Die P/N TES5118.

6. Use Tessera Tape 22099D1AX, where X=suffix whichidentifies tape manufacturer.

7. Elastomer=Tessera P/N.106000100108 (Dow Corning 6810 Encapsulant).103000100108 (Dow Corning 6910 Spacer Adhesive).

8. Parts to be cleaned per Tessera cleaning instructions APN01.

9. Make from eutectic solder ball (ø0.3mm). Dimensions apply aftersolder ball reflow.

10. Datum Z established by high points of solder bumps.

11. Elastomer shall not extend beyond datum A.

��

µBGA

µBall Grid Array

TV-46

Part Number SystemTV-74AµBall Grid Array

I/O Count

Daisy-Chain Type

A= Qualified Daisy-Chain (reliability evaluation, stress,life cycle testing).

AM=Mechanical Daisy-Chain (package handling, pickand place evaluation).

New!


µBGA

TV-62

Notes:

1. Dimensioning and tolerancing per ASME Y14.5M–1994.

2. Do not subject part to ultrasonic cleaning.

3. Mark back of die with laser.

4. Contact ball position designation per JESD 95–1, SPP –010.

5. Silicon Die, 2000 Grit Grind.

6. Use Tessera Tape 26399D1AX, where X=suffix which identifies tapemanufacturer.

7. Elastomer=Tessera P/N as follows:106000100108 (Dow Corning 6811 Encapsulant).103000100108 (Dow Corning 6910 Spacer Adhesive).

8. (Not used)

��

See Section Detail Side View (Scale=None)

Z 13

SeatingPlane

Back View

8.8±0.025 Die

A1 CornerIndex

11±-.025 Die

(Nom) Z X

3

DIR

ECT

- RD

RAM

µBG

ATV

- 62

TTA

PE D

.C.

YYW

W D

LLLL

®

RA

MB

US

®®Te

sser

a

Bump View Datum Axis 'X'4X RO.2 Max

9.3±0.05

(4.65)

8X 1

134 256789101112

2X 1.6

DatumAxis 'X'

4X — 0.05

(5.75)

11.5±0.05

4X 0.8

2X 1.2

X

A

B

C

D

E

F

G

H

J

TV

62TR

AM

BU

S µ

BG

A®

▲

A

Die (0.4±0.025) thick

ø0.35±0.030.05 Z


Elastomer 7


▲

Z

0.25±0.03 10

13

ø0.1 Z XYø0.05 Z

12

ST

// 0.1 Z

0.89±0.05

ø0.3 (Conductor)

9. Parts to be cleaned per Tessera cleaning instructions APN01.

10. Make from eutectic solder ball (ø0.35mm). Dimensions apply aftersolder ball reflow.

11. (Not used)

12.

13.

Elastomer is not allowed to extend beyond datum A.

Datum Z established by high points of solder bumps.

(Nom) Z X

New!


µBGA

TV-74

▲

Z 10

Die (0.4±0.025 thick)

ø0.3±0.03

Lead

Adhesive

0.05 Z



Elastomer Seal4 Sides/Edges 7 11

0.19±0.03 9

9ø0.1 Z XYø0.05 Z

▲A

0.77±0.05

ST

// 0.1 Z

Elastomer 7

(Nom) Z X

15X 0.75

Notes:1. Dimensioning and tolerancing per ASME Y14.5M–1994.2. Do not subject part to ultrasonic cleaning or intense UV.3. Mark back of die with laser.

4. Contact ball position designation per JESD 95–1,SPP –010.5. Die P/N TES5119.6. Use Tessera Tape 22799D1AX, where X=Suffix which identifies tape

manufacturer.7. Elastomer=Tessera P/N.

106000100108 (Dow Corning 6810 Encapsulant).103000100108 (Dow Corning 6910 Spacer Adhesive).

��

8. Parts to be cleaned per Tessera cleaning instructions APN01.9. Make from eutectic solder ball (ø0.3mm). Dimensions apply after solder

ball reflow.10. Datum Z established by high points of solder bumps.11. Elastomer shall not extend beyond datum A.

Die 5

A1 Corner

Index 3

Back View

(7.49) Die

(12.29) Die

DIR

EC

T - R

DR

AM

µB

GA

MTV

- 74

ME

CH

AN

ICA

LY

YW

W M

LLLL

®

RA

MB

US

®®Te

sser

a

Bump View

A

B

C

D

E

F

G

H

J

K

L

M

N

P

R

T

7 6 5 3 2 1

Datum Axis 'X'

DatumAxis 'Y'

4X R0.2 Max

12.7±0.05

8.17±0.05

(6.35)

Die Pad 2Die Pad 14X — 0.05

▲

Y

(4.085)

6X 0.75

0.375

4

RA

MB

US

TV

74

µB

GA

®®

▲

Z 10

SeatingPlane

See Section Detail Side View


TB-188 Test Board

Tessera®

®

TV-188M µBGA®

DAISY-CHAINTEST SITE

12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

TV-188M µBGA®


12 3 4 5 6

12

11

10

9

8

7

18 17 16 15 14 13A1

19

20

21

22

23

24

25 25 25 25

2525252525

25

µBGA® PN 324—0168—REV00 TOP

TV–188M DAISY CHAIN TEST BOARD

Not to scaleThe TB–188 test board has 10 daisy-chain test sites on one side,

and 10 bias/SIR test sites on the other, for use with the TV–188M

µBGA daisy-chain test package on both sides. The two sides are

laid out so as to use the same solder stencil aligned to three

global fiducial.

The test board is not perforated for snap-apart, but it is

designed so it can be cut into testable 5–up or 1–up coupons. The

drilled holes are for hard wiring with solder for in-situ testing at the

panel or coupon level (no plated through-holes).

Notes� Board is made with nickel/gold solder-

pad finish.

� Actual size of board is 2.75" x 6.5".

Order Number: TB188

TB-46 Test Board

Notes� Test board has 10 daisy-chained chip sites per board.

� Board is made with nickel/gold solder-pad finish.

� Gerber data for solder stencil is supplied at no charge.

TB-74 Test BoardPlease call for details.

Not to scale

®Tessera µBGA TB 13371T1A

TV46 TEST BOARD 7 – 16 – 96

98

76

54

3

10 11 12 13 14 15

2 1 24 23 22 2116

1718

1920

TE

ST

BO

AR

DµB

GA

™

1337

1T1A

-7dl

g

94U-Ø

-35 3697 DCI

®

98

76

54

3

10 11 12 13 14 15

2 1 24 23 22 2116

1718

1920

TE

ST

BO

AR

DµB

GA

™

1337

1T1A

-6dl

g

94U-Ø

-35 3697 DCI

®

98

76

54

3

10 11 12 13 14 15

2 1 24 23 22 2116

1718

1920

TE

ST

BO

AR

DµB

GA

™

1337

1T1A

-8dl

g

94U-Ø

-35 3697 DCI

®

98

76

54

3

10 11 12 13 14 15

2 1 24 23 22 2116

1718

1920

TE

ST

BO

AR

DµB

GA

™

1337

1T1A

-9dl

g

94U-Ø

-35 3697 DCI

®

98

76

54

3

10 11 12 13 14 15

2 1 24 23 22 2116

1718

1920

TE

ST

BO

AR

DµB

GA

™

1337

1T1A

-10

dlg

94U-Ø

-35 3697 DCI

®

98

76

54

3

101112131415

212423222116

1718

1920

TE

ST

BO

AR

DµB

GA

™

13371T1A

-5dlg 94U-Ø

-35 3697DCI

®

98

76

54

3

101112131415

212423222116

1718

1920

TE

ST

BO

AR

DµB

GA

™

13371T1A

-4dlg 94U-Ø

-35 3697DCI

®

98

76

54

3

101112131415

212423222116

1718

1920

TE

ST

BO

AR

DµB

GA

™

13371T1A

-3dlg 94U-Ø

-35 3697DCI

®

98

76

54

3

101112131415

212423222116

1718

1920

TE

ST

BO

AR

DµB

GA

™

13371T1A

-2dlg 94U-Ø

-35 3697DCI

®

98

76

54

3

101112131415

212423222116

1718

1920

TE

ST

BO

AR

DµB

GA

™

13371T1A

-1dlg 94U-Ø

-35 3697DCI

®

Order Number: TB46

µBGA Test Boards


Flip Chip

Part Number FB250 FB500 FA10-200 orFA10-400

PB8-200 orPB8-400 x 600 PST2

Die Size 250 x 250 mils 500 x 500 mils200 x 200 mils400 x 400 mils

200 x 200 mils400 x 600 mils

150 x 150 mils

Bump Pitch 457 µm, 18 mil 457 µm, 18 mil 254 µm, 10 mil 203 µm, 8 mil 457 µm, 18 milPassivation Via 102 µm 102 µm 80 µm 73 µm 102 µmUBM Diameter 152 µm 152 µm 102 µm 95 µm 152 µm

Bump Height 140 µm 140 µm 110 µm 98 µm 130 µmBump Diameter 190 µm 190 µm 135 µm 120 µm 160 µm

No. of Bumps 48 96 317 88 21Max. Bump Diagonal 7.7 mm 16.5 mm 7.9 mm — —

Pad Size 193 x 193 µm 193 x 193 µm 127 x 127 µm 115 x 115 µm 165 x 165 µmThickness 12 kA 12 kA 12 kA 12 kA 40 kA

DieMetal

Type 98/1/1 Al/Cu/Si 98/1/1 Al/Cu/Si 98/1/1 Al/Cu/Si 98/1/1 Al/Cu/Si 98/1/1 Al/Cu/Si

Packaging

Uncut Wafer*

5" Wafer250 x 250 mils

(243 Die)


(48 Die)


(379 Die)400 x 400 mils

(86 Die)


(379 Die)400 x 600 mils

(50 Die)


(682 Die)

Tray

Sawed 5" Wafer25 per tray 2" sq

Waffle Pack


Waffle Pack

Sawed 5" Wafer36 per tray 200 x 2009 per tray 400 x 400

Waffle Pack

Sawed 5" Wafer36 per tray 200 x 2009 per tray 400 x 600

Waffle Pack


Waffle Pack

Tape and Reel.400 PitchTack Tape

12mm Width

.600 PitchTack Tape

24mm Width

.400 PitchTack Tape

12mm Width

.400 PitchTack Tape

12mm Width

Call ForAvailability

*Note: Die count represents expected yield per wafer.

Epoxy EncapsulantChip

Flip Chip BumpFB250

Substrate


Flip Chip Test Boards

Laminate BoardLaminate board is double-sided board. One

side has 10 pads for the FB250, the other side

has 10 pads for the FB500.

Ceramic BoardCeramic board is single sided. FB250 ceramic

board has 10 pads on one side. The FB500

ceramic board has 10 pads on one side.

Order Number: FB250-PCB

Top view

Order Number: FB500-PCB

Bottom view


Flip Chip Test Boards

Laminate BoardLaminate board is double-sided board. One

side has 10 pads for the PB8-2x2, the other

side has 10 pads for the PB8-4x6.

Ceramic BoardCeramic board is not available.

Order Number: PB8-2x2-PCB

Top view

Order Number: PB8-4x6-PCB

Bottom view

Laminate BoardLaminate is only available for FA10-2x2.

Ceramic BoardCeramic is not available.

Order Number: FA10-2x2-PCB

Top view only


QFP

Plastic Quad Flat Pack

Part Number Numberof Pins Body Size Lead Pitch Footprint Quantity

Per TrayTapeWidth

TapePitch

QuantityPer Reel

QFP44-10mm-.8mm-3.2 44 10mm sq .8mm 3.2mm 90/96 24mm 24mm 500QFP44-10mm-.8mm-3.9 44 10mm sq .8mm 3.9mm 90/96 24mm 24mm 500QFP64-14mm-.8mm-3.2 64 14mm sq .8mm 3.2mm 84 32mm 24mm 350QFP64-14x20mm-1.0mm-3.2 64 14 x 20mm 1.0mm 3.2mm 50/66 44mm 32mm 350QFP64-14x20mm-1.0mm-3.9 64 14 x 20mm 1.0mm 3.9mm 50/66 44mm 32mm 350QFP80-14x20mm-.8mm-3.2 80 14 x 20mm .8mm 3.2mm 50/66 44mm 32mm 350QFP80-14x20mm-.8mm-3.9 80 14 x 20mm .8mm 3.9mm 50/66 44mm 32mm 350QFP100-14x20mm-.65mm-3.2 100 14 x 20mm .65mm 3.2mm 50/66 44mm 32mm 200QFP100-14x20mm-.65mm-3.9 100 14 x 20mm .65mm 3.9mm 50/66 44mm 32mm 200QFP120-28mm-.8mm-3.2 120 28mm sq .8mm 3.2mm 24 44mm 40mm 200QFP120-28mm-.8mm-3.9 120 28mm sq .8mm 3.9mm 24 44mm 40mm 200QFP160-28mm-.65mm-3.2 160 28mm sq .65mm 3.2mm 24 44mm 40mm 200QFP160-28mm-.65mm-3.9 160 28mm sq .65mm 3.9mm 24 44mm 40mm 200QFP208-28mm-.5mm-2.6 208 28mm sq .5mm 2.6mm 24 44mm 40mm 200QFP240-32mm-.5mm-2.6 240 32mm sq .5mm 2.6mm 24 — — N/AQFP256-28mm-.4mm-2.6 256 28mm sq .4mm 2.6mm 24 44mm 40mm 200QFP304-40mm-.5mm-2.6 304 40mm sq .5mm 2.6mm 12 — — N/A

Notes� All QFPs are standard in JEDEC trays.

� Tray quantities may vary.

Part Number System

S L

R1

R2

Gage Plane

0.25mmθ3

θ2

-H-

θ1

θ

-C-

0.10 C

Seating Plane

e

D2D1D

E2

E1E

bbb C A-B D4X

aaa C A-B D4X

c

L1

A

A2A1

s0.

10

b

-A-

-B-

-D-

ccc M C A-B S D S

QFP44-10mm-.8mm-3.2mm QFP44-10mm-.8mm-3.9mmMillimeter Inch Millimeter Inch

Min Nom Max Min Nom Max Min Nom Max Min Nom MaxA — — 2.55 — — 0.100 A — — 2.45 — — 0.096A1 0.15 0.25 0.35 0.006 0.010 0.014 A1 0.15 0.25 0.35 0.006 0.010 0.014A2 1.80 2.05 2.20 0.071 0.081 0.087 A2 1.95 2.05 2.10 0.077 0.081 0.083D 13.20 BSC. 0.520 BSC. D 13.90 BSC. 0.547 BSC.D1 10.00 BSC. 0.394 BSC. D1 10.00 BSC. 0.394 BSC.E 13.20 BSC. 0.520 BSC. E 13.90 BSC. 0.547 BSC.

E1 10.00 BSC. 0.394 BSC. E1 10.00 BSC. 0.394 BSC.R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — —θ 0º — 7º 0º — 7º θ 0º 3.5º 7º 0º 3.5º 7ºθ1 0º — — 0º — — θ1 0º — — 0º — —θ2 10º Ref 10º Ref θ2 10º Ref 10º Refθ3 7º Ref 7º Ref θ3 7º Ref 7º Refc 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041L1 1.60 0.063 L1 1.95 Ref 0.077 RefS 0.20 — — 0.008 — — S 0.40 — — 0.016 — —b 0.30 0.35 0.45 0.012 0.014 0.018 b 0.30 0.35 0.45 0.012 0.014 0.018e 0.80 BSC. 0.031 BSC. e 0.80 BSC. 0.031 BSC.

D2 8.00 0.315 D2 8.0 0.315E2 8.00 0.315 E2 8.0 0.315

Tolerances of Form and Position Tolerances of Form and Positionaaa 0.25 0.010 aaa 0.25 0.010bbb 0.20 0.008 bbb 0.20 0.008ccc — 0.20 — — 0.008 — ccc — 0.20 — — 0.008 —Note: Control dimensions are in millimeters.

QFP44–10mm–.8mm–3.9mmQuadFlat Pack

Number of Pins Lead PitchBodySize

LeadFootprint

Add “TR” to end of part number for Tape and Reel.


S L

R1

R2

Gage Plane

0.25mmθ3

θ2

-H-

-C-

ddd C

Seating Plane

e

E2

E1E

D2D1D

bbb C A-B D4X

aaa C A-B D4X

θ

θ1 b

s0.

10

c

L1

A

A2 A1

-D-

-A-

-B-

ccc M C A-B S D S

QFP

QFP64-14x20mm-1.0mm-3.2mm QFP64-14x20mm-1.0mm-3.9mmMillimeter Inch Millimeter Inch

Min Nom Max Min Nom Max Min Nom Max Min Nom MaxA — — 3.40 — — 0.134 A — — 3.40 — — 0.134A1 0.25 — — 0.010 — — A1 0.15 0.25 0.35 0.006 0.010 0.014A2 2.50 2.72 2.90 0.098 0.107 0.114 A2 2.55 2.72 3.05 0.100 0.107 0.120D 23.20 BSC. 0.913 BSC. D 23.90 BSC. 0.941 BSC.D1 20.00 BSC. 0.787 BSC. D1 20.00 BSC. 0.787 BSC.E 17.90 BSC. 0.677 BSC. E 17.90 BSC. 0.705 BSC.

E1 14.00 BSC. 0.551 BSC. E1 14.00 BSC. 0.551 BSC.R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — —θ 0º — 7º 0º — 7º θ 0º 3.5º 7º 0º 3.5º 7ºθ1 0º — — 0º — — θ1 0º — — 0º — —

Alloy 42 L/F θ2, θ3 7º Ref 7º Ref θ2, θ3 7º Ref 7º RefCopper L/F θ2, θ3 15º Ref 15º Ref θ2, θ3 15º Ref 15º Ref

c 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041L1 1.60 Ref 0.063 Ref L1 1.95 Ref 0.077 RefS 0.20 — — 0.008 — — S 0.40 — — 0.016 — —b 0.35 0.40 0.50 0.014 0.016 0.020 b 0.35 0.40 0.50 0.014 0.016 0.020e 1.00 BSC. 0.039 BSC. e 1.00 BSC. 0.039 BSC.

D2 18.00 Ref. 0.709 Ref. D2 18.00 Ref. 0.709 Ref.E2 12.00 Ref. 0.472 Ref. E2 12.00 Ref. 0.472 Ref.

Tolerances of Form and Position Tolerances of Form and Positionaaa 0.25 0.010 aaa 0.25 0.010bbb 0.20 0.008 bbb 0.20 0.008ccc — 0.20 — — 0.008 — ccc — 0.20 — — 0.008 —ddd — 0.10 — — 0.004 —

Note: Control dimensions are in millimeters.

QFP80-14x20mm-.8mm-3.2mm QFP80-14x20mm-.8mm-3.9mm QFP100-14x20mm-.65mm-3.2mm QFP100-14x20mm-.65mm-3.9mmMillimeter Inch Millimeter Inch Millimeter Inch Millimeter Inch

Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom MaxA — — 3.40 — — 0.134 A — — 3.40 — — 0.134 A — — 3.40 — — 0.134 A — — 3.40 — — 0.134

A1 0.25 — — 0.010 — — A1 0.15 0.25 0.35 0.006 0.010 0.014 A1 0.25 — — 0.010 — — A1 0.15 0.25 0.35 0.006 0.010 0.014A2 2.50 2.72 2.90 0.098 0.107 0.114 A2 2.55 2.72 3.05 0.100 0.107 0.120 A2 2.50 2.72 2.90 0.098 0.107 0.114 A2 2.55 2.72 3.05 0.100 0.107 0.120D 23.20 BSC. 0.913 BSC. D 23.90 BSC. 0.941 BSC. D 23.20 BSC. 0.913 BSC. D 23.90 BSC. 0.941 BSC.

D1 20.00 BSC. 0.787 BSC. D1 20.00 BSC. 0.787 BSC. D1 20.00 BSC. 0.787 BSC. D1 20.00 BSC. 0.787 BSC.E 17.90 BSC. 0.677 BSC. E 17.90 BSC. 0.705 BSC. E 17.90 BSC. 0.677 BSC. E 17.90 BSC. 0.705 BSC.E1 14.00 BSC. 0.551 BSC. E1 14.00 BSC. 0.551 BSC. E1 14.00 BSC. 0.551 BSC. E1 14.00 BSC. 0.551 BSC.R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — —θ 0º — 7º 0º — 7º θ 0º 3.5º 7º 0º 3.5º 7º θ 0º — 7º 0º — 7º θ 0º 3.5º 7º 0º 3.5º 7º

θ1 0º — — 0º — — θ1 0º — — 0º — — θ1 0º — — 0º — — θ1 0º — — 0º — —

Alloy 42 L/F θ2, θ3 7º Ref 7º Ref θ2, θ3 7º Ref 7º Ref θ2, θ3 7º Ref 7º Ref θ2, θ3 7º Ref 7º Ref

Copper L/F θ2, θ3 15º Ref 15º Ref θ2, θ3 15º Ref 15º Ref θ2, θ3 15º Ref 15º Ref θ2, θ3 15º Ref 15º Refc 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041

L1 1.60 Ref 0.063 Ref L1 1.95 Ref 0.077 Ref L1 1.60 Ref 0.063 Ref L1 1.95 Ref 0.077 RefS 0.20 — — 0.008 — — S 0.40 — — 0.016 — — S 0.20 — — 0.008 — — S 0.40 — — 0.016 — —b 0.30 0.35 0.45 0.012 0.014 0.018 b 0.30 0.35 0.45 0.012 0.014 0.018 b 0.22 0.30 0.38 0.009 0.012 0.015 b 0.22 0.30 0.38 0.009 0.012 0.015e 0.80 BSC. 0.031 BSC. e 0.80 BSC. 0.031 BSC. e 0.65 BSC. 0.026 BSC. e 0.65 BSC. 0.026 BSC.

D2 18.40 Ref. 0.724 Ref. D2 18.40 Ref. 0.724 Ref. D2 18.85 Ref. 0.742 D2 18.85 Ref. 0.742 Ref.E2 12.00 Ref. 0.472 Ref. E2 12.00 Ref. 0.472 Ref. E2 12.35 Ref. 0.486 E2 12.35 Ref. 0.486 Ref.

Tolerances of Form and Position Tolerances of Form and Position Tolerances of Form and Position Tolerances of Form and Positionaaa 0.25 0.010 aaa 0.25 0.010 aaa 0.25 0.010 aaa 0.25 0.010bbb 0.20 0.008 bbb 0.20 0.008 bbb 0.20 0.008 bbb 0.20 0.008ccc — 0.20 — — 0.008 — ccc — 0.20 — — 0.008 — ccc — 0.13 — — 0.005 — ccc — 0.12 — — 0.005 —ddd — 0.10 — — 0.004 — ddd — 0.10 — — 0.004 —

Note: Control dimensions are in millimeters.


QFP

e

D2D1D

E2

E1E

aaa C A-B D4Xbbb C A-B D4X c

L1

A

A2A1

s0.

10

bθ1

S L

R1

R2

Gage Plane

0.25mmθ3

θ2

-H-

θ

0.10 C

-C- Seating Plane

-D-

-B-

-A-

ccc M C A-B S D S

QFP120-28mm-.8mm-3.2mm QFP120-28mm-.8mm-3.9 QFP160-28mm-.65mm-3.2 QFP160-28mm-.65mm-3.9Millimeter Inch Millimeter Inch Millimeter Inch Millimeter Inch

Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom Max Min Nom MaxA — — 4.10 — — 0.161 A — — 4.07 — — 0.160 A — — 4.10 — — 0.161 A — — 4.07 — — 0.160

A1 0.25 — — 0.010 — — A1 0.15 0.25 0.35 0.006 0.010 0.014 A1 0.25 — — 0.010 — — A1 0.15 0.25 0.35 0.006 0.010 0.014A2 3.20 3.32 3.60 0.126 0.131 0.142 A2 3.17 3.32 3.67 0.125 0.131 0.144 A2 3.20 3.32 3.60 0.126 0.131 0.142 A2 3.17 3.32 3.67 0.125 0.131 0.144D 31.20 BSC. 1.228 BSC. D 31.90 BSC. 1.256 BSC. D 31.20 BSC. 1.228 BSC. D 31.90 BSC. 1.256 BSC.

D1 28.00 BSC. 1.102 BSC. D1 28.00 BSC. 1.102 BSC. D1 28.00 BSC. 1.102 BSC. D1 28.00 BSC. 1.102 BSC.E 31.20 BSC. 1.228 BSC. E 31.90 BSC. 1.256 BSC. E 31.20 BSC. 1.228 BSC. E 31.90 BSC. 1.256 BSC.E1 28.00 BSC. 1.102 BSC. E1 28.00 BSC. 1.102 BSC. E1 28.00 BSC. 1.102 BSC. E1 28.00 BSC. 1.102 BSC.R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012 R2 0.13 — 0.30 0.005 — 0.012R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — — R1 0.13 — — 0.005 — —θ 0º — 7º 0º — 7º θ 0º 3.5º 7º 0º 3.5º 7º θ 0º — 7º 0º — 7º θ 0º 3.5º 7º 0º 3.5º 7ºθ1 0º — — 0º — — θ1 0º — — 0º — — θ1 0º — — 0º — — θ1 0º — — 0º — —θ2 8º Ref 8º Ref θ2 8º Ref 8º Ref θ2 8º Ref 8º Ref θ2 8º Ref 8º Refθ3 8º Ref 8º Ref θ3 8º Ref 8º Ref θ3 8º Ref 8º Ref θ3 8º Ref 8º Refc 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009 c 0.11 0.15 0.23 0.004 0.006 0.009L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041 L 0.73 0.88 1.03 0.029 0.035 0.041

L1 1.60 Ref 0.063 Ref L1 1.95 Ref 0.077 Ref L1 1.60 Ref 0.063 Ref L1 1.95 Ref 0.077 RefS 0.20 — — 0.008 — — S 0.40 — — 0.016 — — S 0.20 — — 0.008 — — S 0.40 — — 0.016 — —b 0.30 0.35 0.45 0.012 0.014 0.018 b 0.30 0.35 0.45 0.012 0.014 0.018 b 0.22 0.30 0.38 0.009 0.012 0.015 b 0.22 0.30 0.38 0.009 0.012 0.015e 0.80 BSC. 0.031 BSC. e 0.80 BSC. 0.031 BSC. e 0.65 BSC. 0.026 BSC. e 0.65 BSC. 0.026 BSC.

D2 23.20 0.913 D2 23.20 0.913 D2 25.35 0.998 D2 25.35 0.998E2 23.20 0.913 E2 23.20 0.913 E2 25.35 0.998 E2 25.35 0.998

Tolerances of Form and Position Tolerances of Form and Position Tolerances of Form and Position Tolerances of Form and Positionaaa 0.25 0.010 aaa 0.25 0.010 aaa 0.25 0.010 aaa 0.25 0.010bbb 0.20 0.008 bbb 0.20 0.008 bbb 0.20 0.008 bbb 0.20 0.008ccc — 0.20 — — 0.008 — ccc — 0.10 — — 0.004 — ccc — 0.13 — — 0.005 — ccc — 0.10 — — 0.004 —

ddd — 0.20 — — 0.008 — ddd — 0.12 — — 0.005 —Note: Control dimensions are in millimeters.


QFN

0.75 Typ

7.00

±0.

05

7.15

Max

0.20±0.060.1

0.13 M⊕0.125±0.030

0.25±0.10Typ

Top View

Bottom View

Surface Roughness: 6±2µ (RZ)m

A A

0.05 Max

ø1.0

Section A-A

RO 15Typ

10° Typ

3° Typ

0.225

Detail A

7.15 Max7.00±0.05

2.5048

136

24

2.50

12

RO 33-

CO 35

ø2.00

0.10 Max

0.50

1

48

36

12

24

01JAPAN

A1

01JAPAN

A1

0.80±0.05A

Part Number Numberof Pads Body Size Pitch

QFN48-7.15x7.15mm-.5mm 48 7.15 x 7.15mm .5mm

Part Number Numberof Pins Body Size Lead Pitch Footprint Quantity

Per TrayTapeWidth

TapePitch

QuantityPer Reel

LQFP32-7mm-.8mm-2.0 32 7mm sq .8mm 2.0mm 250 16mm 12mm 1,000LQFP48-7mm-.5mm-2.0 48 7mm sq .5mm 2.0mm 250 16mm 12mm 1,000LQFP64-14mm-.8mm-2.0 64 14mm sq .8mm 2.0mm 90 32mm 24mm 1,000LQFP64-10mm-.5mm-2.0 64 10mm sq .5mm 2.0mm 160 24mm 24mm 1,000LQFP80-10mm-.4mm-2.0 80 10mm sq .4mm 2.0mm 160 24mm 24mm 1,000LQFP80-12mm-.5mm-2.0 80 12mm sq .5mm 2.0mm 90 24mm 20/24mm 1,000LQFP80-14mm-.65mm-2.0 80 14mm sq .65mm 2.0mm 90 32mm 24mm 1,000LQFP100-14mm-.5mm-2.0 100 14mm sq .5mm 2.0mm 90 32mm 24mm 750LQFP100-14x20mm-.65mm-2.0 100 14 x 20mm .65mm 2.0mm 90 44mm 24mm 500LQFP120-14mm-.4mm-2.0 120 14mm sq .4mm 2.0mm 90 32mm 24mm 750LQFP144-20mm-.5mm-2.0 144 20mm sq .5mm 2.0mm 60 44mm 24mm 750LQFP168-14mm-.3mm-2.0 168 14mm sq .3mm 2.0mm 90 32mm 24mm 500LQFP176-20mm-.4mm-.2.0 176 20mm sq .4mm 2.0mm 60 44mm 24mm 500LQFP176-24mm-.5mm-2.0 176 24mm sq .5mm 2.0mm 40 44mm 32mm 500LQFP208-28mm-.5mm-2.0 208 28mm sq .5mm 2.0mm 36 44mm 40mm 500LQFP256-28mm-.4mm-2.0 256 28mm sq .4mm 2.0mm 36 44mm 40mm 500

Low Profile Quad Flat Pack

LQFP

Notes� All LQFPs are standard in trays.

� LQFPs have a body thickness of 1.4mm.

� Tray quantity may vary.

Part Number System

Quad Flat Pack Non-Leaded

Part Number System

QFN48-7.15x7.15mm-.5mmQuad Flat PackNon-Leaded

Pad Count

Pitch

Body Size

LQFP48–7mm–.5mm–2.0Low ProfileQuad Flat Pack

Number of Pins Lead PitchBodySize

LeadFootprint

Add “TR” to end of part number for Tape and Reel.


Part Number Numberof Pins Body Size Lead Pitch

BQFP100-22.6mm-.636mm 100 22.6mm .636mmBQFP132-27.7mm-.636mm 132 27.7mm .636mm

BQFP100–22.6mm–.636mmBumpered QuadFlat Pack

Number of Pins

LeadPitch

Body Size

Notes� BQFPs are packaged in JEDEC trays.


� BQFP packages are expected to be phased out (obsolete) due

to low demand. Please call for availability.

D G C Z

E

X

Y

Z

C

G

D

GridPlacementCourtyard

Y

YX

Full Radius Optional

BE

W

A

H

S

L

T

ComponentIdentifier Z (mm) G (mm) X (mm Y (mm)

RefC (mm)

RefD (mm)

RefE (mm)Basic

Placement Grid(No. of Grid Elements)

BQFP 100 23.20 19.60 0.35 1.80 21.40 15.24 0.63 50 x 50BQFP 132 28.20 24.60 0.35 1.80 26.40 20.32 0.63 58 x 58

Component L (mm) S (mm) W (mm) T (mm) A (mm) B (mm) E (mm) H (mm)Identifier Min Max Min Max Min Max Min Max Max Max Basic Max

BQFP 100 22.10 22.60 20.10 20.71 0.20 0.30 0.75 1.00 19.35 19.35 0.635 4.57BQFP 132 27.20 27.20 25.25 25.81 0.20 0.30 0.75 1.00 24.20 24.20 0.635 4.57

BQFP

BQFP Component Dimensions

BQFP Land Pattern Dimensions

Part Number System

Bumpered Quad Flat Pack


Part Number Number ofCastellations Pitch Body Size

16LCC-1.27mm-7.36x8.96mm 16 1.27mm 7.36 x 8.96mm20LCC-1.27mm-8.90mm 20 1.27mm 8.90mm sq28LCC-1.27mm-11.5mm 28 1.27mm 11.5mm sq32LCC-1.27mm-11.4x14.0mm 32 1.27mm 11.4 x 14.0mm32LCC-1.27mm-11.4x16.5mm 32 1.27mm 11.4 x 16.5mm40LCC-1.00mm-10.1mm 40 1.00mm 10.1mm sq48LCC-1.00mm-14.2mm 48 1.00mm 14.2mm sq52LCC-1.27mm-19.0mm 52 1.27mm 19.0mm sq68LCC-1.27mm-24.11mm 68 1.27mm 24.11mm sq84LCC-1.27mm-29.2mm 84 1.27mm 29.2mm sq

Part Number Numberof Pins Body Width Lead Pitch

52CQFP-19.0mm-1.27mm 52 19.0mm sq 1.27mm68CQFP-24.1mm-1.27mm 68 24.1mm sq 1.27mm84CQFP-16.5mm-.65mm 84 16.5mm sq .65mm100CQFP-19.0mm-.65mm 100 19.0mm sq .65mm132CQFP-24.1mm-.65mm 132 24.1mm sq .65mm144CQFP-26.6mm-.65mm 144 26.6mm sq .65mm172CQFP-29.2mm-.65mm 172 29.2mm sq .65mm196CQFP-32.0mm-.50mm 196 32.0mm sq .50mm

CQFP

Ceramic Quad Flat Pack

Part Number SystemNotes� CQPFs are available with or without combo lid.

� Pins are flat (sandwiched) with tie bar.

� Parts are packaged in non-JEDEC trays.

� Due to the custom nature of the package, body size and

dimensions can change without notice.

LCC

Leadless Ceramic Carrier

Part Number SystemNotes� LCCs are available with or without combo lid.

� Gold castellations are standard, but can be solder coated.

� Parts are packaged in non-JEDEC trays.

� Parts are available with a daisy-chain configuration

upon request.

20LCC–1.27mm–8.90mmNumber ofCastellations

Castellation Pitch

Body Size

LeadlessCeramic Carrier

52CQFP–19.0mm–1.27mmI/O Count

Body Size

Lead Pitch

Ceramic QuadFlat Pack


Component JEDEC L (mm) S (mm) W (mm) T (mm) A (mm) B (mm) H (mm) P (mm)Identifier Number Min Max Min Max Min Max Min Max Min Max Min Max Min Max Basic

SO8 MS-012 AA 5.80 6.30 3.26 4.55 0.33 0.51 0.40 1.27 3.80 4.00 4.80 5.00 1.35 1.75 1.27SO14 MS-012 AB 5.80 6.30 3.26 4.55 0.33 0.51 0.40 1.27 3.80 4.00 8.55 8.75 1.35 1.75 1.27SO16 MS-012 AC 5.80 6.30 3.26 4.55 0.33 0.51 0.40 1.27 3.80 4.00 9.80 10.00 1.35 1.75 1.27

SO16-7.6mm MS-013 AA 10.00 10.65 7.46 8.85 0.33 0.51 0.40 1.27 7.40 7.60 10.10 10.50 2.35 2.65 1.27SO20-7.6mm MS-013 AC 10.00 10.65 7.46 8.85 0.33 0.51 0.40 1.27 7.40 7.60 12.60 13.00 2.35 2.65 1.27SO28-7.6mm MO-119 AB 10.29 10.64 8.21 9.01 0.36 0.51 0.53 1.04 7.40 7.60 18.08 18.39 2.34 2.64 1.27

Part Number Numberof Pins

LeadStyle

BodyWidth

QuantityPer Tube

Part Number(Tape and Reel)

TapeWidth

TapePitch

QuantityPer Reel

SO8GT-3.8mm 8 Gull 3.8mm 99 SO8GTR-3.8mm 12mm 8mm 2,500SO14GT-3.8mm 14 Gull 3.8mm 50 SO14GTR-3.8mm 16mm 8mm 2,500SO16GT-3.8mm 16 Gull 3.8mm 50 SO16GTR-3.8mm 16mm 8mm 2,500SO16GT-7.6mm 16 Gull 7.6mm 46 SO16GTR-7.6mm 16mm 12mm 1,000SO20GT-7.6mm 20 Gull 7.6mm 38 SO20GTR-7.6mm 24mm 12mm 1,000SO28GT-7.6mm 28 Gull 7.6mm 25 SO28GTR-7.6mm 24mm 12mm 1,000SO32GT-7.6mm 32 Gull 7.6mm 25 SO32GTR-7.6mm 1,000SO20/26JT-7.6mm 20/26 J-Lead 7.6mm 25 SO20/26JTR-7.6mm 24mm 12mm 1,000SO28JT-7.6mm 28 J-Lead 7.6mm 27 SO28JTR-7.6mm 24mm 12mm 1,000SO40JT-10mm 40 J-Lead 10.0mm 17 SO40JTR-10mm 44mm 16mm 500

SOIC

SOIC Component Dimensions

SOIC Land Pattern Dimensions

Small Outline Integrated Circuit

Notes� Standard lead pitch is 1.27mm.

� Tube quantity may vary.

Part Number System

ComponentIdentifier Z (mm) G (mm) X (mm) Y (mm)

RefC (mm)

RefD (mm)

RefE (mm)

RefPlacement Grid

(No. of Grid Elements)SO8 7.40 3.00 0.60 2.20 5.20 3.81 1.27 12 x 16

SO14 7.40 3.00 0.60 2.20 5.20 7.62 1.27 20 x 16SO16 7.40 3.00 0.60 2.20 5.20 8.89 1.27 22 x 16

SO16-7.6mm 11.40 7.00 0.60 2.20 9.20 8.89 1.27 22 x 22SO20-7.6mm 11.40 7.00 0.60 2.20 9.20 11.43 1.27 28 x 24SO28-7.6mm 11.40 7.00 0.60 2.20 9.20 16.51 1.27 38 x 24

B

A S L

HWP

D

G Z

Y

C

E X


SO14GT–3.8mmSmall OutlineIntegrated Circuit

Number of Pins

Body Size

Packaging

Lead Style: G=Gull Wing, J=J-LeadedPackaging: T= Tubes, TR=Tape and Reel

Lead Style


Part Number Numberof Pins Body Size Lead

PitchQuantityPer Tray

TapeWidth

TapePitch

QuantityPer Reel

TI-TSOP20/24-6x14.4mm-.5mm 20/24 6 x 14.4mm .5mm 240 24mm 12mm 1,000TI-TSOP28-8.1x11.8mm-.55mm 28 8.1 x 11.8mm .55mm 234 24mm 12mm 1,000TI-TSOP28/32-8x18.4mm-.5mm 28/32 8 x 18.4mm .5mm 156 32mm 12/16mm 1,000TI-TSOP32-8x18.4mm-.5mm 32 8 x 18.4mm .5mm 156 32mm 12/16mm 1,000TI-TSOP40-10x18.4mm-.5mm 40 10 x 18.4mm .5mm 120 32mm 16mm 1,000TI-TSOP48-12x18.4mm-.5mm 48 12 x 18.4mm .5mm 96 32mm 16mm 1,000

Part Number Numberof Pins Body Size Lead

PitchQuantityPer Tray

TapeWidth

TapePitch

QuantityPer Reel

TII-TSOP20/26-7.6x17.14mm-1.27mm 20/26 7.6 x 17.14mm 1.27mm 176 24mm 12mm 1,000TII-TSOP24/26-7.6x17.14mm-1.27mm 24/26 7.6 x 17.14mm 1.27mm 176 24mm 12mm 1,000TII-TSOP24/28-10.16x18.41mm-1.27 24/28 10.16 x 18.41mm 1.27mm 100 32mm 16mm 1,000TII-TSOP26-7.6mmx17.14mm-1.27mm 26 7.6 x 17.14mm 1.27mm 176 24mm 12mm 1,000TII-TSOP32-10.16x20.95mm-1.27mm 32 10.16 x 20.95mm 1.27mm 117 32mm 16mm 1,000TII-TSOP40/44-10.16x18.42mm-.8mm 40/44 10.16 x 18.42mm .8mm 135 32mm 16mm 1,000TII-TSOP44-10.16x18.42mm-.8mm 44 10.16 x 18.42mm .8mm 135 32mm 16mm 1,000TII-TSOP50-10.16x20.95mm-.8mm 50 10.16 x 20.95mm .8mm 117 32mm 16mm 1,000TII-TSOP54-10.16x22.22mm-.8mm 54 10.16 x 22.22mm .8mm 108 44mm 20mm 1,000TII-TSOP54-12.7x22.22mm-.8mm 54 12.7 x 22.22mm .8mm 84 44/32mm 20mm 1,000

Thin Small Outline Package – Type I

Thin Small Outline Package – Type II

Notes� Standard packaging is in JEDEC trays or tape and reel

(quantities may vary).

� Body dimensions are measured by body length and width.

� Type I means that pins extend from the narrow end (the width)

of the body.

� Type II means that pins extend from the wide end (the length)

of the body.

Part Number System

TSOP

TI–TSOP28–8.1x11.8mm–.5mm

Thin SmallOutline Package

Numberof Pins

LeadPitch

Body Size


Type I or Type II


Notes:

1. Dimensions and tolerancing per ANSI Y14.5M-1982.

2. “D” and “E1” are reference datums and do not include mold deflash orprotrusions, but do include mold mismatch and are measured at the partingline. Mold deflash or protrusions shall not exceed 0.15 (.006") per side. Endflash from the package body shall not exceed 0.15 (.006") per side (D).

3. Dimension “L” is the length of terminal for soldering to a substrate.

4. “N” is the number of terminal positions.

5. Formed leads shall be planar with respect to one another within 0.10(.004") at seating plane.

6. Dimension “b” does not include dambar protrusion/intrusion. Dambarprotrusion to be 0.13 (.005") max per side.

D

1.14

1.14

1.14 Dia.152 DP Max

EE1

2

Datum Plane

Seating PlaneBase Plane

b

e

A1A

5

Side View

Top View Bottom View

Dia. Pin Y236.125 DP Max

C

A

A2

End View

b1BaseMetal

With LeadFinish

bSection BB

c c1

Note: All dimensions are in millimeters.

Gauge Plane

Seating Plane0.25

3

7°±5°

8°±1° Typical

Detail A

1.25 Ref(.049")

B

L

B

R

D

Common DimensionMin Nom Max

Inch mm Inch mm Inch mm NoteA .068 1.73 .073 1.86 .078 2.00A1 .002 0.05 .005 0.13 .008 0.20A2 .065 1.65 .069 1.75 .073 1.85b .009 0.22 .012 0.30 .015 0.38b1 .009 0.22 .012 0.30 .013 0.33c .004 0.09 .006 0.15 .010 0.25c1 .004 0.09 .006 0.15 .008 0.21D See The Specific Part Number 2E .291 7.40 .307 7.80 .323 8.20

E1 .197 5.00 .209 5.30 .221 5.60 2e .026 Inch 0.65 mm BSCL .022 0.55 .030 0.75 .037 0.95 3N See The Specific Part Number 4R .004 0.09

D 0° 4° 8°

Part Number Numberof Pins Body Width Quantity

Per Tube Tape Width Tape Pitch QuantityPer Reel

SSOP8T-5.3mm 8 5.3mm 156 12mm 8mm 2,500SSOP14T-5.3mm 14 5.3mm 100 12/16mm 12mm 1,000SSOP16T-5.3mm 16 5.3mm 80 12/16mm 12mm 1,000SSOP20T-5.3mm 20 5.3mm 62 16mm 12mm 1,000SSOP24T-5.3mm 24 5.3mm 66 16mm 12mm 1,000SSOP28T-5.3mm 28 5.3mm 47 16/24mm 12mm 1,000SSOP48T-7.6mm 48 7.6mm 30 32mm 12/16mm 1,000SSOP56T-7.6mm 56 7.6mm 26 32mm 12/16mm 500SSOP64T-10.2mm 64 10.2mm — 44mm 16/24mm 500

SSOP

Small Shrink Outline Package


� Standard body width is 5.3mm.


Part Number System

SSOP8T-5.3mm to SSOP28T-5.3mm

SSOP20T–5.3mmSmall ShrinkOutline Package

Number of Pins

Body Width

Packaging

Packaging: T= Tubes, TR=Tape and Reel

D 2

Part 4 Min Nom MaxNumber N Inch mm Inch mm Inch mm

SSOP8T-5.3mm 8 .106 2.70 .118 3.00 .130 3.30SSOP14T-5.3mm 14 .232 5.90 .244 6.20 .256 6.50SSOP16T-5.3mm 16 .232 5.90 .244 6.20 .256 6.50SSOP20T-5.3mm 20 .271 6.90 .283 7.20 .295 7.50SSOP24T-5.3mm 24 .311 7.90 .323 8.20 .334 8.50SSOP28T-5.3mm 28 .390 9.90 .402 10.20 .413 10.50


SSOP

SSOP 48T-7.6mm

SSOP 56T-7.6mm

48 25

241

-B-

-A-

E1 E

-D-

b 0.007" M C A—B S D S

0.010" C A—B S D S

e

D

A2 A

A10.004" C

θ

L

Gauge Plane

0.010°

Detail F

L1

Seating Plane

-C-

c

See Detail F

Notes:

1. Dimension D does not include mold flash, protrusions or gate burs. Moldflash protrusions or gate burs shall not exced 0.006 per side.

2. Dimension E1 does not include interlead flash or prorusion. Interlead flashor protrusion shall not exceed 0.015 per side.

Millimeter InchMin Nom Max Min Nom Max

A 2.41 2.59 2.79 0.095 0.102 0.110A1 0.20 0.30 0.40 0.008 0.012 0.016A2 2.26 2.39 2.52 0.089 0.094 0.099b 0.20 0.25 0.34 0.008 0.010 0.0135c 0.13 0.20 0.25 0.005 0.008 0.010D 15.75 15.88 16.00 0.620 0.625 0.630E1 7.39 7.49 7.59 0.291 0.295 0.299e 0.64 BSC 0.025 BSCE 10.03 10.31 10.67 0.395 0.406 0.420L 0.51 0.76 1.02 0.020 0.030 0.040L1 1.42 0.056θ 0° 8° 0° 8°

Note: Controlling Dimension — Inch

Millimeter InchMin Nom Max Min Nom Max

A 2.41 2.59 2.79 0.095 0.102 0.110A1 0.20 0.30 0.40 0.008 0.012 0.016A2 2.26 2.39 2.52 0.089 0.094 0.099b 0.20 0.25 0.34 0.008 0.010 0.0135c 0.13 0.20 0.25 0.005 0.008 0.010D 18.29 18.42 18.54 0.720 0.725 0.730E1 7.39 7.49 7.59 0.291 0.295 0.299e 0.64 BSC 0.025 BSCE 10.03 10.31 10.67 0.395 0.406 0.420L 0.51 0.76 1.02 0.020 0.030 0.040L1 1.42 0.056θ 0° 8° 0° 8°

Note: Controlling Dimension — Inch

Notes:

1. Dimension D does not include mold flash, protrusions or gate burs. Moldflash protrusions or gate burs shall not exced 0.006 per side.

2. Dimension E1 does not include interlead flash or prorusion. Interlead flashor protrusion shall not exceed 0.015 per side.

0.010" C A—B S D S

56 29

281

-B-

-A-

E1 E

-D-

b 0.007" M C A—B S D S

e

D

A2 A

A10.004" C

θ

L

Gauge Plane

0.010°

Detail F

L1

Seating Plane

-C-

c

See Detail F


Part Number Numberof Pins Body Width Tape Width Tape Pitch Quantity

Per TubeQuantityPer Reel

TSSOP8T-4.4mm 8 4.4mm 12/16mm 8mm 100 1,000/2,500TSSOP14T-4.4mm 14 4.4mm 12/16mm 8mm 96 1,000/2,500TSSOP16T-4.4mm 16 4.4mm 12/16mm 8mm 96 1,000/2,500TSSOP20T-4.4mm 20 4.4mm 16mm 8/12mm 76 1,000/2,500TSSOP24T-4.4mm 24 4.4mm 16mm 8/12mm 63 1,000/2,500TSSOP28T-4.4mm 28 4.4mm 16mm 8/12mm 50 1,000TSSOP38T-4.4mm 38 4.4mm 16mm 8/12mm 43 1,000TSSOP48T-6.1mm 48 6.1mm 24mm 12mm 39 1,000TSSOP56T-6.1mm 56 6.1mm 24mm 12mm 35 1,000

Thin Shrink Small Outline Package

TSSOP


� Standard body width is 5.3mm.


Part Number System

TSSOP8T–4.4mmThin Shrink SmallOutline Package

Number of Pins Packaging


Body Width


SON 24 Pin

Exposed Pad

1.00

1.000.325 Typ

3.10

2.50

Mark (Cavity)Top Side

0.65

A1A1

5.60

±0.

05

5.85

Max

Surface Roughness: 6±2µ (RZ)

RO 15Typ

4-10°

0.05 Max

ø1.0

7.80±0.058.05 Max

0.24±0.06

4-10°

0.1

0.13 M⊕

0.60±0.05

0.125±0.030

0.50±0.10

0.50±0.10

0.27±0.06

2.20

Top View Bottom Viewm

SON

Part Number Numberof Pads Body Size Pitch

SON20-5.45x7.45mm-.65mm 20 5.45 x 7.45mm .65mmSON24-5.85x8.05mm-.65mm 24 5.85 x 8.05mm .65mmSON40-10.10x10.75mm-.5mm* 40 10.10 x 10.75mm .5mmSON46-10.10x12.00mm-.5mm* 46 10.10 x 12.00mm .5mm

Part Number SystemNote� Parts are packaged in trays or tubes.

Small Outline Non-Leaded Package

SON20–5.45x7.45mm–.65mmSmall OutlineNon-Leaded

Package

Pad Count

Pitch

Body Size

1.00

1.00

0.675 Typ

Mark (Cavity)Top Side

0.65

A1A1

5.30

±0.

05

5.45

Max

ø1.0

7.20±0.057.45 Max

0.30±0.060.1

0.13 M�

0.80±0.05

0.125±0.030

0.51±0.10

0.50±0.10

0.25±0.06

2.20

Top View Bottom ViewSurface Roughness: 6±2µ (RZ)m

1 10

20

A A

0.05 Max

10

201

Section A-A

RO 15Typ

10° Typ

3° Typ

0.225

Detail A

SON 20 Pin


Component L (mm) S (mm) W (mm) T (mm) A (mm) B (mm) J (mm) H (mm) P (mm)Identifier Min Max Min Max Min Max Min Max Min Max Min Max Ref Max BasicPLCC-20 9.78 10.03 5.78 6.53 0.33 0.53 1.50 2.00 8.89 9.04 8.89 9.04 7.87 4.57 1.27PLCC-28 12.32 12.57 8.32 9.07 0.33 0.53 1.50 2.00 11.43 11.58 11.43 11.58 10.41 4.57 1.27PLCC-44 17.40 17.65 13.40 14.15 0.33 0.53 1.50 2.00 16.51 16.66 16.51 16.66 15.49 4.57 1.27PLCC-52 19.94 20.19 15.94 16.69 0.33 0.53 1.50 2.00 19.05 19.20 19.05 19.20 18.03 5.08 1.27PLCC-68 25.02 25.27 21.02 21.77 0.33 0.53 1.50 2.00 24.13 24.33 24.13 24.33 23.11 5.08 1.27PLCC-84 30.10 30.35 26.10 26.85 0.33 0.53 1.50 2.00 29.21 29.41 29.21 29.41 28.19 5.08 1.27

Part Number(In Tubes) Pin Count Body Size Quantity

Per TubePart Number(Tape and Reel) Tape Width Tape Pitch Quantity

Per ReelPLCC20T 20 8.8mm 48 PLCC20TR 16mm 12mm 1,000PLCC28T 28 11.4mm 38 PLCC28TR 24mm 16mm 750PLCC32T 32 11.4 x 13mm 30 PLCC32TR 24mm 16mm 750PLCC44T 44 16.5mm 28 PLCC44TR 32mm 24mm 500PLCC52T 52 19.0mm 24 PLCC52TR 32mm 24mm 500PLCC68T 68 24.1mm 17 PLCC68TR 44mm 32mm 250PLCC84T 84 29.2mm 15 PLCC84TR 44mm 36mm 250

PLCC Land Patterns

PLCC Component Dimensions

Plastic Leaded Chip Carrier

PLCC

Notes� All PLCCs have “J” leads.

� 13" reels are standard.


� Standard lead pitch is 1.27mm (50 mils).

� PLCCs are to JEDEC standards.

Part Number System

PLCC20TPlastic Leaded Chip Carrier

Number of Pins

Packaging


H

S J L

T

PW

A

B

L

E

ZG

D C

C GridPlacementCourtyard

Heel

Y

X

Full Radius Optional

ComponentIdentifier Z (mm) G (mm) X (mm) Y (mm)

RefC (mm)

RefD (mm)

RefE (mm)

RefPlacement Grid

(No. of Elements)PLCC-20 10.80 6.40 0.60 2.20 8.60 5.08 1.27 24 x 24PLCC-28 13.40 9.00 0.60 2.20 11.20 7.62 1.27 30 x 30PLCC-44 18.40 14.00 0.60 2.20 16.20 12.70 1.27 40 x 40PLCC-52 21.00 16.60 0.60 2.20 18.80 15.24 1.27 44 x 44PLCC-68 26.00 21.60 0.60 2.20 23.80 20.32 1.27 54 x 54PLCC-84 31.20 26.80 0.60 2.20 29.00 25.40 1.27 66 x 66



Body Size-A-

Body Leads-S- SC Device Tape

WidthTapePitch

QuantityPer 7" Reel

SC90-TR (Supermini) 3 1.6mm 1.6mm SC-75A 8mm 4mm 3,000SOT323-TR 3 2.0mm 2.1mm SC-70 8mm 4mm 3,000SOT325-TR 5 2.0mm 2.1mm SC-88A 8mm 4mm 3,000SOT326-TR 6 2.0mm 2.1mm SC-88 8mm 4mm 3,000SOT23-TR 3 2.9mm 2.4mm 8mm 4mm 3,000SOT25-TR 5 2.9mm 2.4mm 8mm 4mm 3,000SOT26-TR 6 2.9mm 2.8mm 8mm 4mm 3,000SOT143-TR 4 2.9mm 2.8mm 8mm 4mm 3,000SOT89-TR 3 4.5mm 4.0mm SC-62 12mm 4mm 1,000SOT223-TR 3 6.7mm 7.3mm 12mm 8mm 1,000DPAK(TO-252)-TR 6.5mm 9.5mm SC-63 16mm 8mm 2,500D2PAK(TO-263)-TR 10.29mm 15.88mm 24mm 12mm 800/1,000

Surface Mount Transistors

SMT

Part Number SystemNotes� Carrier pack is plastic for surface mount transistors.

S

A

SOT326–TRTransistor Package Packaging



Component Identifier(mm) (in) Z (mm) G (mm) X (mm) Y (mm)

RefC (mm)

RefPlacement Grid

(No. of Grid Elements)0603 (0201) 0.72 0.26 0.32 0.23 0.49 —1005 (0402) 2.20 0.40 0.70 0.90 1.40 2 x 61608 (0603) 2.80 0.60 1.00 1.10 1.70 4 x 62012 (0805) 3.20 0.60 1.50 1.30 1.90 4 x 83216 (1206) 4.40 1.20 1.80 1.60 2.80 4 x 103225 (1210) 4.40 1.20 2.70 1.60 2.80 6 x 104532 (1812) 5.80 2.00 3.40 1.60 3.90 8 x 12

Component Dimensions L (mm) S (mm) W (mm) T (mm) H (mm)(mm) (in) Min Max Min Max Min Max Min Max Max

0603 (0201) 0.57 0.63 — — 0.27 0.33 — — 0.331005 (0402) 0.90 1.10 0.30 0.65 0.40 0.60 0.10 0.30 0.601608 (0603) 1.45 1.75 0.45 0.97 0.65 0.95 0.20 0.50 0.852012 (0805) 1.80 2.20 0.30 1.11 1.05 1.45 0.25 0.75 1.103216 (1206) 3.00 3.40 1.50 2.31 1.40 1.80 0.25 0.75 1.353225 (1210) 3.00 3.40 1.50 2.31 2.30 2.70 0.25 0.75 1.354532 (1812) 4.20 4.80 2.30 3.46 3.00 3.40 0.25 0.95 1.35

Body SizePart Number

(Inch) (mm)Tape Width Tape Pitch Quantity

Per 7" ReelQuantityBulk Cassette

0805SMC-PL .08" x .05" 2.0 x 1.2mm 8mm 4mm 4,000 10,0001206SMC-PL .12" x .06" 3.2 x 1.6mm 8mm 4mm 3,000 5,0001210SMC-PL .12" x .10" 3.2 x 2.5mm 8mm 4mm 3,000 —1812SMC-PL .18" x .12" 4.5 x 3.2mm 12mm 8mm 1,1001825SMC-PL .18" x .25" 4.5 x 6.4mm 12mm 8mm 1,000


(Inch) (mm)Tape Width Tape Pitch Quantity


0201SMC-PA .02" x .01" 0.6 x 0.3mm 8mm 2mm 15,000 50,0000402SMC-PA .04" x .02" 1.0 x .05mm 8mm 2mm 10,000 50,0000603SMC-PA .06" x .03" 1.5 x .08mm 8mm 4mm 4,000 15,0000805SMC-PA .08" x .05" 2.0 x 1.2mm 8mm 4mm 5,000 10,0001206SMC-PA .12" x .06" 3.2 x 1.6mm 8mm 4mm 4,000 5,000

SMC

SMC Component Dimensions

SMC Land Pattern Dimensions

Surface Mount Ceramic Capacitors – Plastic Tape

Surface Mount Ceramic Capacitors – Paper Tape

Notes� Surface mount capacitors come on standard 7" reels (larger

quantity reels are available upon request).

� Plastic carrier tape is non-standard for some carrier sizes.

� The numeric section of the part number refers to the physical

body size (in inches) of the component. For example: Part

number 0805SMC-PL has a body size of .08" length by .05" width.

Part Number System0402SMC–PACase Size in Inches

Surface Mount Ceramic Capacitor

Tape Type

Tape Type: PA= Paper Tape, PL=Plastic TapeAdd “B” at end of part number for bulk.Add “C” at end of part number for bulk cassette feeder.

LT

W

H

S

C

G

Z

X

Y



Component Identifier(mm) (in) Z (mm) G (mm) X (mm) Y (mm) Ref C (mm) Ref Placement Grid

(No. of Grid Elements)1005 (0402) 2.20 0.40 0.70 0.90 1.30 2 x 6

1608 (0603) 2.80 0.60 1.00 1.10 1.70 4 x 6

2012 (0805)* 3.20 0.60 1.50 1.30 1.90 4 x 8

3216 (1206)* 4.40 1.20 1.80 1.60 2.80 4 x 10

3225 (1210)* 4.40 1.20 2.70 1.60 2.80 6 x 10

Component Dimensions L (mm) S (mm) W (mm) T (mm) H (mm)(mm) (in) Min Max Min Max Min Max Min Max Max

1005 (0402) 1.00 1.10 0.40 0.70 0.48 0.60 0.10 0.30 0.401608 (0603) 1.50 1.70 0.70 1.11 0.70 0.95 0.15 0.40 0.602012 (0805) 1.85 2.15 0.55 1.32 1.10 1.40 0.15 0.65 0.653216 (1206) 3.05 3.35 1.55 2.32 1.45 1.75 0.25 0.71 0.713225 (1210) 3.05 3.35 1.55 2.32 2.34 2.64 0.25 0.71 0.71


(Inches) (mm)Tape Width Tape Pitch Quantity


0402SMR-PA .04" x .02" 1.0 x .05mm 8mm 2mm 10,000 80,0000603SMR-PA .06" x .03" 1.6 x .08mm 8mm 4mm 5,000 25,0000805SMR-PA .08" x .05" 2.0 x 1.2mm 8mm 4mm 5,000 10,0001206SMR-PA .12" x .06" 3.2 x 1.6mm 8mm 4mm 5,000 5,0001210SMR-PA .12" x .10" 3.2 x 2.5mm 8mm 4mm 5,000 —

SMR

SMR Component Dimensions

SMR Land Pattern Dimensions

*Note: If a more robust pattern is desired for wave soldering

devices larger than 1608 (0603), add 0.2mm to the Y dimension

Surface Mount Resistors

Bulk Cassette Feeder

Notes� Surface mount resistors come packaged on paper carrier tape

and 7" reels (larger quantities are available upon request).

� Plastic carrier tape is non-standard for surface mount resistors.

� The numeric section of the part number refers to the physical

body size (in inches) of the component. For example: Part

number 0402SMR-PA has a body size of .04" length by .02" width.

Part Number System

0402SMR–PABody Size in Inches

Surface Mount Resistor

Tape Type

Tape Type: PA= Paper Tape, PL=Plastic TapeAdd “B” at end of part number for bulk.Add “C” at end of part number for bulk cassette feeder.

LT

W

H

S

C

G

Z

X

Y


and consider reducing the X dimension by 30%. Add a “W” suffix

to the number; e.g., 103w.

53.3

10.0 1.5 +0.1-0

3.0+0.2-0

6.8 ± 0.1 8.8± 0.1

12.0± 0.1

2.0+0.-0.1

110 ±0.7 5.0

19.0

31.5+0.2-0

36.0+0.-0.2

Bulk Case Dimensions in mm.


SMTA

Part Number Body Size Case Size Tape Width Tape Pitch Quantity7" Reel

3216SMTA-PL 3.2 x 1.6mm A 8mm 4mm 2,0003528SMTA-PL 3.5 x 2.8mm B 8mm 4mm 2,0006032SMTA-PL 6.0 x 3.2mm C 12mm 8mm 500/7507343SMTA-PL 7.3 x 4.3mm D 12mm 8mm 500/750

Component Identifier(mm) Z (mm G (mm) X (mm) Y (mm)

RefC (mm)

RefPlacement Grid

(No. of Grid Elements)3216 4.80 0.80 1.20 2.00 2.80 6 x 123528 5.00 1.00 2.20 2.00 3.00 8 x 126032 7.60 2.40 2.20 2.60 5.00 8 x 187343 9.00 3.80 2.40 2.60 6.40 10 x 20

Component Identifier L (mm) S (mm) W1 (mm) W2 (mm) T (mm) H1 (mm) H2 (mm)(mm) Min Max Min Max Min Max Min Max Min Max Max Min3216 3.00 3.40 0.80 1.74 1.17 1.21 1.40 1.80 0.50 1.10 0.70 1.803528 3.30 3.70 1.10 2.04 2.19 2.21 2.60 3.00 0.50 1.10 0.70 2.106032 5.70 6.30 2.50 3.54 2.19 2.21 2.90 3.50 1.00 1.60 1.00 2.807343 7.00 7.60 3.80 4.84 2.39 2.41 4.00 4.50 1.00 1.60 1.00 3.10

Zero Ohm


(Inches) (mm)Tape Width Tape Pitch Quantity

7" Reel0402SMR-PA-0 .04" x .02" 1.0 x .05mm 8mm 4mm 10,0000603SMR-PA-0 .06" x .03" 1.6 x .08mm 8mm 4mm 5,0000805SMR-PA-0 .08" x .05" 2.0 x 1.2mm 8mm 4mm 5,0001206SMR-PA-0 .12" x .06" 3.2 x 1.6mm 8mm 4mm 5,000

Zero Ohm Jumper Resistors

Note� Plastic carrier tape is non-standard for surface mount resistors.

Part Number System0402SMR–PA–0Case Size in Inches

Tape Type

Zero Ohm

Surface Mount Resistor

Tape Type: PA= Paper Tape, PL=Plastic Tape

Surface Mount Tantalum Capacitor

SMTA Land Pattern Dimensions

SMTA Component Dimensions

Notes� Components are molded, surface mount tantalums.

� Conformal coated tantalums are available.

� Please call for availability of mil-spec surface mount tantalums.

� Standard reel size is 7" (larger sizes are available upon request).

� All tantalum capacitors are on plastic carrier pack.

Part Number System

C

G

Z

X

Y


WW

SL

HH

T2 Places

1

2

1

2

3216SMTA–PLCase Size inMillimeters Plastic Carrier Pack

Surface MountTantalum Capacitor


Part Number Body Size Quantity7" Reel Tape Width Tape Pitch Quantity

13" ReelSOD80-TR 1.4 x 3.4mm 2,500 8mm 4mm 10,000SOD80 Package is also known as LL-34 or DO-213AA.SM1-TR 2.6 x 5.0mm 1,500 12mm 4mm 5,000Package is also known as LL-41 or DO-213AB.

Part Number Body Size Tape Width Tape Pitch Quantity13" Reel

3mm-SME-PL 3mm 12mm 8mm 2,0004mm-SME-PL 4mm 12mm 8mm 2,0005mm-SME-PL 5mm 12mm 12mm 1,0006.3mm-SME-PL 6.3mm 16mm 12mm 1,0008mm-SME-PL 8mm 16mm 12mm 1,00010mm-SME-PL 10mm 16mm 16mm 500

SME

Surface Mount Electrolytic Capacitors

Part Number System3mm–SME–PLBody Size Plastic Carrier Pack

Surface MountElectrolytic Capacitor

X2P

10 16V

øD±0.5

Plastic Platform 0.3 Max

B±0.2

5.4+0.1-0.2

C±0.2

Positive

Negative

0.5 Max

E

A±0.2

A±0.2

0.5~0.8

3 4 5 6.3

1.5 1.8 2.1 2.4

3.3 4.3 5.3 6.6

3.3 4.3 5.3 6.6

0.8 1.0 1.3 2.2

A

B

C

E

øD(mm)

Notes� Melf Diodes are cylindrical glass or plastic packages.

Melf Diodes

Part Number System

SOD80–TRDevice/Package Tape and Reel

A B

PackageDimension ADimension B

SOD80 (LL34)3.4 mm1.5 mm

SM1 (LL41)5.0 mm2.8 mm

Notes� Surface mount electrolytic capacitors come standard on

15" reels.

� Components are measured by the diameter of the

electrolytic can.


Part Number

1/8-W-AR-1.6X3.7mm-TR1/4-W-AR-2.3X6.5mm-TR1/2-W-AR-3.5X9.5mm-TR


TO5-3-B 3TO92-3-B 3TO220-3-B 3

Notes� Parts are conformal coated resistors - carbon film type.

Axial Leaded Resistors

TO

Through-Hole Transistors

Part Number System

Part Number System

TO5–3–B Packaging

Number of Pins

Packaging: B=Bulk, T=Tubes, TR=Tape and Reel

Transistor Package

4.8

4.8

12.7 Min.

2.5 Min.

0.5

2.5

(1) (2) (3)

0.452.3

3.7

5

EBC(1) Emitter(2) Base(3) Collector

ECB(1) Emitter(2) Collector(3) Base Dimensions: mm

2.54 2.54

0.8

1.3

ø3.17.0

10.0

13.5 Min.

17.012.0

5.0

8.0

(1) Base(2) Collector(3) Emitter

4.5

2.8

0.55 2.6

1.8

(1) (2) (3)

(1) (2) (3) Dimensions: mm

1/8–W–AR–1.6x3.7mm–TRWattage Size

Body Size

Tape and Reel

Axial ResistorPackage


Custom PCB Practice Kits

Design A Custom PCB Practice Board Or CompleteKit To Meet Your Specific Requirements.Practical Components will help you design custom practice PC

boards or complete kits. Use the building blocks below to create

your board and start saving time and money using dummy parts

and a PCB practice kit. Please contact your service representative

for more information.

Stencil� Metal mask stencil is

used for solder printingwhich is available forcustom or Practicalboard.

Gerber Data� Software data used to

create a metal maskstencil for solder pasteapplication.

X, Y and Theta Data� Software used to

calibrate pick and placemachines for placementof components to PCB.

Delivery�

�

Standard delivery is4 to 6 weeks.Expedited deliveryis available.

Board Material��

FR4 (standard)Polyimide

Board Size/Thickness��

4" x 5.5" (standard)8" x 5.5".062"Other

Fiducials/Tooling Holes

�

�

Fiducials are used toorient the position ofeach individualcomponent to populatethe board.Tooling holes are .125"

� Doughnut (local andglobal)

LP/Alpha Level�

�

LPI is a photo liquidimageable solder maskthat will not interfere withsolder paste screenprinting.Alpha level (silver flash)

Parts for PC Board� Capacitor QFP

Transistor TSOPSOIC BGAPLCC TantalumCSBGA Other

� �Resistor LQFP�

� ��

Final ProductPCB Practice Kit


SO8

SO8

SO8

SOT23SO14

SO14 SO14

SO14

SOJ20 26

SOJ20 26

SOJ20 26

SO8

SOT143

SO20 SO20

SO20SO20

PRACTICALCOMPONENTS

PLCC209

14

9

14

1

34

23

12QFP44

.8mm PITCH

1

34

23

12QFP44

.8mm PITCH

T1+ T1–

8A

H

1

CSBGA48 T1+ T1–

8A

H

1

CSBGA48

DPAK

PLCC201 1

39 39

29 29

18 18

7 7

PLCC44 PLCC44

1

76

5126

LQFP100.5mm PITCH

10

1

60

44

27

PLCC68

10

1

60

44

27

PLCC68TSOP32TSOP32

0402 0402

0402

0402

0603 0603

0603

0603

08051206

08051206

0805

1206

08051206

TANTALUMC

D

A

B

+ +

++

P/N PC008 REV C FAX: 714.899.8599

PHON

E: 7

14.8

99.8

309

E-MA

IL: KLPCI@W

ORLDN

ET.ATT.NET

Solder Practice Board and Kits

A universal PCB to meet all your needs.Rework practice, solder training and evaluation, and for testing

and calibration of pick-and-place machines.

Part Number NumberPer Board Part Number Number

Per BoardCSBGA-8sq.-1.0mm 2 SO20GTR-7.6mm 4PBGA169-1.5mm-23mm-T 2 SO20/26JT-7.6mm 3PBGA225-1.5mm-27mm-T 2 SOT23-TR 4PBGA352-1.27mm-35mm-T 2 SOT143-TR 4PQFP44-10mm-.8mm-3.9mm 2 D Pak(TO252)-TR 1PQFP100-14x20mm-.65mm-3.9mm 2 3216SMTA-PL 1PQFP208-28mm-.5mm-2.6mm 2 3528SMTA-PL 1PQFP256-28mm-.4mm-2.6mm 2 6032SMTA-PL 1LQFP100-14mm-.5mm-2.0mm 1 7343SMTA-PL 1TI-TSOP32-8x20mm-.5mm 2 0402SMR-PA 52PLCC20-TR 2 0603SMR-PA 42PLCC44-TR 2 0805SMR-PL 36PLCC68-TR 2 1206SMR-PL 32SO8GTR-3.8mm 4 PCB008 Board 1SO14GTR-7.6mm 4

PC008 Solder Practice Board


Top view—actual size of board is 5.5" x 8".


T1+ T2+ T3+ T4+

T4+T1– T4–

BGA1691.5mm PITCH

BGA3521.27mm PITCH

BGA2251.5mm PITCH

T1+ T2+ T3+ T4+

T1– T2– T3– T4–

T2– T3–T1+ T2+ T3+

T1– T2– T3– T4–

T1+ T2+ T3+ T4+

T4+T1– T4–

BGA1691.5mm PITCH

BGA3521.27mm PITCH

BGA2251.5mm PITCH

T1+ T2+ T3+ T4+

T1– T2– T3– T4–

T2– T3–T1+ T2+ T3+

T1– T2– T3– T4–

© 1998 PRACTICAL COMPONENTS, INC.

18

51

31

QFP100.65mm PITCH

18

51

31

QFP100.65mm PITCH

QFP256.4mm PITCH

QFP256.4mm PITCH

1157

10553

QFP208.5mm PITCH

1157

10553

QFP208.5mm PITCH

Solder Practice Board and Kits

Quantity Of Parts Per Kit

Order Number PBGA169

PBGA225

PBGA352 Boards QFP100-

.65mmQFP208-.5mm

QFP256-.4mm

PC008-BGA-6 12 12 12 6PC008-BGA-12 24 24 24 12PC008-BGA-24 48 48 48 24PC008-BGA-48 96 96 96 48PC008-QFP-6 6 12 12 12PC008-QFP-12 12 24 24 24PC008-QFP-24 24 48 48 48PC008-QFP-48 48 96 96 96PC008-BGA/QFP-6 12 12 12 6 12 12 12PC008-BGA/QFP-12 24 24 24 12 24 24 24PC008-BGA/QFP-24 48 48 48 24 48 48 48PC008-BGA/QFP-48 96 96 96 48 96 96 96

PC008 Solder Practice Board

Note� Gerber Data and X,Y Theta Data are available if required at

no charge

PC008 Practice Board KitsChoose from the kits below or create your own custom configuration.

Bottom view—actual size of board is 5.5" x 8".


PC008 Test Board

BGA Daisy-Chain Patterns for the PC008 Test Board

T-4 T+4 T+2 T-2 T-1 T+1 T-3 T+3T-4T+4T+2T-2T-1T+1T-3T+3T-4T+4T+2T-2T-1T+1T-3T+3

BGA 169 Daisy Chain

X-Ray ViewAfter Mounting to Test BoardBall View

T-4 T+4 T+2T-2 T-1 T+1 T-3 T+3T-4T+4T+2 T-2T-1T+1T-3T+3T-4T+4T+2 T-2T-1T+1T-3T+3

BGA 225 Daisy Chain


1234567891011121314151 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

AB

C

E

D

F

G

H

J

L

M

K

N

P

R

AB

C

E

D

F

G

H

J

L

M

K

N

P

R

AB

C

E

D

F

G

H

J

L

M

K

N

P

R

T-4T+4T+2T-2T-1T+1 T-3 T+3 T-4 T+4 T+2 T-2 T-1 T+1T-3T+3T-4T+4T+2T-2T-1T+1 T-3 T+3

BGA 352 Daisy Chain


ABC

ED

FGHJ

LM

K

NPRTU

WY

V

AAABACADAEAF

123456789101112131415161718192023 22 212425261 2 3 4 5 6 7 8 9 10 1112 1314 15 16 1718 19 20 232221 24 25 261 2 3 4 5 6 7 8 9 10 1112 1314 15 16 1718 19 20 232221 24 2526

ABC

ED

FGHJ

LM

K

NPRTU

WY

V

AAABACADAEAF

ABC

ED

FGHJ

LM

K

NPRTU

WY

V

AAABACADAEAF

A B C ED F G H J L MK N

2

3

4

5

6

7

8

9

10

11

12

1

13

A B C ED F G H J L MK N

2

3

4

5

6

7

8

9

10

11

12

1

13

ABCE DFGHJLM KN

2

3

4

5

6

7

8

9

10

11

12

1

13


SMTA SABERIPC-SM-782A Version

BGA169 (Daisy Chained) DPAK

QFP100

SOL20TSOP 32

SO16

.010 Wave Test

.020 Wave Test

Screen

Test

SO16

Screen

Test

SIR Test

QFP208

BQFP100

PLCC68

SMTA Saber Board

SMTA Saber Evaluation PC BoardThe SMTA Saber Evaluation PC Board.Practical Components is licensed by SMTA to distribute

the Saber Evaluation PC Board. The Saber Board

includes land patterns for a wide variety of JEDEC and

EIAJ components.

The Saber Board is used to evaluate:� P&P equipment

� Reflow process

� Component placement accuracy

� Cleanliness

� Surface Insulation Resistance (SIR)

� Speed and accuracy of component placement

� Solder paste screening

Note� Gerber Data and X,Y Theta Data are available if

required at no charge.

Order Number: PCB-SABER (Board Only)

Top/bottom view (double-sided)

—actual size of board is 3.875" 5.375".

SMTA Saber Board Kits

Part Number Quantity Per24 Kits

Quantity Per48 Kits

Quantity Per96 Kits

Board 24 48 960402SMR 1000 1632 40000603SMR 1000 1488 30000805SMR 500 1008 20001206SMR 500 960 20001210SMR 500 672 2000SOT23 1000 1152 3000DPAK(TO252) 48 96 200SO16GT-3.8mm 100 144 288SO20GT-7.6mm 24 48 96PLCC68 24 48 96TI-TSOP32 24 48 96PQFP208-.5mm 24 48 96PQFP100-.65mm 24 48 96BQFP100-.636mm 24 48 96PBGA169-1.5mm 24 48 96

Order Number: SMTA-24 SMTA-48 SMTA-96


Part Number QuantityPer Kit

PQFP208-28mm-.5mm-2.6mm 1PQFP44-10mm-.8mm-3.2mm 1PQFP100-14x20mm-3.2mm 1PLCC44-TR 1SO8GT-3.8mm 1SO20GT-7.6mm 1SOT23-TR 3SOT143-TR 20603SMR-PA 60805SMR-PA 31206SMR-PA 6QSOP20T-3.8 3DIP14T-3.8mm 1PCB003 Board 1

Solder Practice Board

SOIC8

SOT23

SOT143

PRACTICALCOMPONENTS

134

2312QFP44 –.8

0603

0603

0603

0805

0805

1206

1206

SOIC20

1

39

29

7

PLCC4418

P/N PC003

DIP14O

.C.

A 94V

–O 81

51

31

QFP100 –.65mm

1157

10553

QFP208 –.5mmQSOP20

© 1999 P

RA

CT

ICA

L CO

MP

ON

EN

TS

, INC

.

PH

ON

E: 7

14.8

99.8

309

F

AX

: 714

.899

.859

9

E-MAIL:[email protected]

PCB003 Solder Practice Board KitPractical Components offers this low cost kitfor solder practice and rework.

PCB003 Solder Practice Board

Top View—actual size of board is 2.5" x 2.5". Bottom View


Order Number: PC003 (Complete Kit)

Note� Gerber Data and X,Y Theta Data are available if required

at no charge


Fine Pitch Training Kit

Through-Hole Training Kit

Standard Pitch Training Kit

Through-Hole Recertification Kit

Kit ContentsQty Description15 Turret Terminal

15 Bifurcated Terminal

15 Hook Terminal

15 Pierced Terminal

15 Cup Terminal

2 Printed Wiring Board

15' 22 Gauge Wire

15' 26 Gauge Wire

10 TO5 Transistor

10 Spacer for TO5

4 TO18 Transistor

Choose the Through-Hole Recertifica-

tion Kit for verification of soldering

operator’s skills for though-hole board

technology.

This kit provides sufficient

components for students to assemble

and solder final workmanship samples

for evaluation.

OMNI Practice And Training Kits

Kit ContentsQty Description4 Small Outline IC (SOIC) 16 pin

(300 mils wide)

10 Small Outline IC (SOIC) 16 pin

(150 mils wide)

5 Plastic Leaded Chip Carrier

(PLCC) 20 Pin

5 Leadless Ceramic Chip Carrier

(LCC)

2 Plastic Leaded Chip Carrier

(PLCC) 44 Pin

Kit ContentsThis kit contains all the material listed

for the TK-2 Standard Pitch Training

Kit plus:

Qty Description4 Quad Flat Packs (QFP) 44 Pin

(0.030" Pitch)

2 Quad Flat Packs (QFP) 100 Pin

(0.025" Pitch)

1 TB4-TB4FP PWB (Replaces

TB4 PWB)

Qty Description14 Small Outline Transistor SOT89

8 Chip Resistor 1206

8 Metal Electrode Face Device

(Melf) SOD80

16 Tantalum Capacitor “C” Case

(6032)

4 Flat Pack 14 Pin

1 TB4 PWB

Order Number: TK-2

Qty Description4 Spacer for TO18

20 1/4 Watt Resistor

12 1/2 Watt Resistor

10 Diode

20 Capacitor (CKO)

4 Capacitor (Axial)

6 DIPs 14/16 Pin

4 Flat Packs 14 Pin

Order Number: TK-1M

Kit ContentsQty Description1 TB3 Through-Hole PWB

3 TO5 Transistor

3 TS5/18 TO5 and TO18 Transistor

Spacer

7 RCO7 1/4 Watt Resistor

2 CKO5 Capacitor

2 IC6 16 Lead DIP

1 FP14 14 Lead Flat Pack

Order Number: TK-1R

Order Number: TK-2FP


OMNI Training Products

Workmanship Acceptance Posters

SMT Workmanship Criteria on CD-ROM

These large (17" x 22") full color posters

depict acceptance criteria for terminals,

through-hole PWB and SMT terminations

in accordance with the latest military and

IPC specifications.

The new format, which includes three

different types of connections per poster,

requires just one-third the wall area of

previous designs. Each poster presents

The latest in Surface Mount Technology

(SMT) workmanship criteria in a user-

friendly CD-ROM format. All criteria is

based on the newest industry specifica-

tions: IPC-A-610-B and J-STD-001B. This

CD-ROM contains over 200 color photo-

graphs and 90 line drawings of SMT

Terminal Holder

1 2 3 4 5 6 7

Recommended for classroom training.This reusable tool safely holds terminals

during wiring and soldering operations.

Terminals will fit snug in holes when

holder is new. The holes are intentionally

slightly undersized to allow for expansion

with use.

three times the information in less space,

making them more functional, economical

and comprehensive. They are ideal for use

in training and production areas for

continual reference to required quality.

P/N: P114 P/N: P115

Poster sizes are 17" x 22".

Order Numbers:

P111 Turret, Bifurcated Side Route and BottomRoute Terminals

P112 Pierced, Hook and Cup Terminals

P113 Clinched, Stud and DIP Top-View

P114 SMC-LCC, Chip and Melf

P115 SMT-Flat Lead (side), Flat Lead (heel)and “J” Leads

F100 Metal Poster Frame (Black)

Order Number: TH-1

1, 7 ......... CT5 Cup Terminal

2, 6 ......... HT3 Hook Terminal

3, 4, 5 ..... TT1 Turret Terminal

3, 4, 5 ..... BT2 Bifurcated Terminal

components, footprints and workmanship

criteria, as well as explanatory text

descriptions.

Minimum System Requirements: 486 or

Pentium Processor, Windows 3.1 or higher,

8 MB of RAM, 2X or higher CD-ROM, 16 bit

video card and VGA or SVGA monitor.

Order Number: CD-WM12


New! Unified Wiring and Soldering Handbook

The Unified Wiring and Soldering Hand-

book has been designed to provide the

electronics manufacturing industry with a

comprehensive step-by-step training

handbook. The use of this cost effective

handbook will greatly simplify the training

of your soldering personnel. The handbook

follows the same format as our Audio

Visual Training Programs (sold separately).

The easy-to-follow process instructions

provide operators with the means for

continual reference and skills updating.

This spiral bound handbook addresses

the workmanship quality standards MIL-

STD-2000A, IPC-A-61 OA and the new joint

industry standard ANSI/J-STD-001. The use

of these handbooks will provide training

for military, medical and all levels of

commercial electronic products. This

training handbook is a must for every

production area and training department.

OMNI Training Products

Unified Inspection Criteria Workmanship ManualsUnified Inspection Criteria Workmanship

Manuals provide all segments of the

electronics manufacturing industry with

the latest SMT and through-hole workman-

ship criteria.

Order Numbers:

WM7 Through-Hole Commercial (B/W)WM8 Through-Hole Commercial and Military

(B/W and Color)WM9 SMT Commercial (B/W)WM10 SMT Commercial and Military

(B/W and Color)

P/N WM8 P/N WM10

This spiral-bound soldering workbook

provides electronics manufacturing

personnel with a comprehensive soldering

training book addressing: Wire prepara-

tion, wiring and soldering terminals,

assembly and soldering of through-hole

components and also placement and

soldering of SMT components.

Each page contains detailed drawings

with provisions for students to record their

notes and applicable workmanship criteria.

This workbook is also an excellent tool to

teach IPC-A 610B or any other commercial,

military or in-house quality standard. The

generic design allows instructors the

opportunity to develop those sections that

are applicable to their training program.

The Soldering Workbook is a must for

every training department.

Order Number: SWB-1

Soldering Workbook

Each handbook addresses the following

areas of workmanship:

No. of

Pages

4 Wire Preparation

7 Turret Terminals

7 Bifurcated Terminals

7 Hook Terminals

8 Pierced Terminals

7 Cup Connectors

12 Printed Wiring Boards

8 Appendix 1: Workmanship criteria

MIL-STD-2000A and IPC-A-610A

4 Appendix 2: Solder connection

criteria

Order Number: HBS-3


OrderNumber

ComponentNumber Pitch Pins

WLSK244 QFP144 .5mm 144WLSK246 QFP208 .5mm 208WLSK247 QFP240 .5mm 240WLSK249 QFP304 .5mm 304WLSK255 QFP144 .65mm 144WLSK256 QFP160 .65mm 160WLSK257 QFP184 .65mm 184

WLSK1000 Lead StraighteningKit Contents:� Patented Precision Alignment Templates

—make it easy to manually reshape bent

leads into correct position

� Lab Grade True Flat Granite

Surface Plate

� 2 Lead Straightening Probes

� Precision Tweezers

� Vacuum Pickup Tool

� Kapton Tape®

� Rugged Storage Box

� Replacement Templates—other size

templates are available

� Instruction Manual

Templates Included in Kit:

Order Number: WLSK1000

Price: $549.50

®Kapton is a registered trademark of Dupont.

Weller QFP Lead Repair Kit

This Kit Makes It Easy To Repair BentLeads And Recover Components ThatMight Otherwise Be Lost.

Lab grade true flat granite surfaceplate provides a stable work

surface and ensures coplanarityafter lead alignment

Lead straightening probes and tweezersmake the delicate process of placement of

bent probes into the correct depressionseasy and repeatable

Patented orientationtemplates make it easy to

manually reshape leadsinto correct position

OrderNumber


WLSK201 QFP180 .015" 180WLSK202 QFP284 .015" 284WLSK203 QFP40 .02" 40WLSK204 QFP52 .02" 52WLSK205 QFP68 .02" 68WLSK206 QFP84 .02" 84WLSK207 QFP132 .02" 132WLSK208 QFP220 .02" 220WLSK209 QFP256 .02" 256WLSK210 QFP44 .025" 44WLSK211 QFP52 .025" 52WLSK212 QFP68 .025" 68WLSK213 QFP84 .025" 84WLSK214 QFP100 .025" 100WLSK215 QFP132 .025" 132WLSK216 QFP148 .025" 148WLSK217 QFP164 .025" 164WLSK218 QFP196 .025" 196WLSK219 QFP244 .025" 244WLSK220 QFP28 .05" 28WLSK221 QFP36 .05" 36WLSK222 QFP44 .05" 44WLSK223 QFP52 .05" 52WLSK224 QFP68 .05" 68WLSK225 QFP84 .05" 84WLSK226 QFP100 .05" 100WLSK227 QFP40 .4mm 40WLSK228 QFP64 .4mm 64

OrderNumber


WLSK229 QFP80 .4mm 80WLSK230 QFP100 .4mm 100WLSK231 QFP120 .4mm 120WLSK232 QFP176 .4mm 176WLSK233 QFP216 .4mm 216WLSK234 QFP256 .4mm 256WLSK235 QFP286 .4mm 286WLSK236 QFP336 .4mm 336WLSK237 QFP376 .4mm 376WLSK238 QFP32 .5mm 32WLSK239 QFP48 .5mm 48WLSK240 QFP64 .5mm 64WLSK241 QFP80 .5mm 80WLSK242 QFP100 .5mm 100WLSK243 QFP128 RECT .5mm 128WLSK245 QFP176 .5mm 176WLSK248 QFP272 .5mm 272WLSK250 QFP40 .65mm 40WLSK251 QFP52 .65mm 52WLSK252 QFP64 .65mm 64WLSK253 QFP80 .65mm 80WLSK254 QFP100 RECT .65mm 100WLSK258 QFP232 .65mm 232WLSK259 QFP32 .8mm 32WLSK260 QFP44 .8mm 44WLSK261 QFP52 .8mm 52WLSK262 QFP64 .8mm 64WLSK263 QFP80 RECT .8mm 80WLSK264 QFP120 .8mm 120WLSK265 QFP128 .8mm 128WLSK266 QFP36 1.0mm 36WLSK267 QFP44 1.0mm 44WLSK268 QFP52 1.0mm 52WLSK269 QFP64 RECT 1.0mm 64

Templates (Available Separately)

Templates (Available Separately)


OrderNumber Pitch Matrix

WPRB210 1.00mm StaggeredWPRB100F 1.00mm FullWPRB203 1.27mm StaggeredWPRB127F 1.27mm FullWPRB205 1.50mm StaggeredWPRB150F 1.50mm Full

WPRB1000 Kit Contents:� 6 Templates

� Vial of 10,000 Eutectic Solder Balls

� BGA Template Clamping Fixture

� Straight Probe

� Bent Probe

� Tweezers

� Screwdriver

� Spatula

� Squeegee

� Flux Pen

� Kapton® Tape

� Dummy BGA Component

� Instruction Manual

Templates Included in Kit:

Order Number: WPRB1000

Price: $549.50

®Kapton is a registered trademark of Dupont

Weller Reballing Kit

BGA template clamping fixtureensures critical ball placement

on the BGA componentA vial of 10,000eutectic solder balls

Precision screening/positioningtemplates for the most commonBGA pitches—replacementtemplates are available

Reball BGA Components ToOriginal Condition AndSave Time And Money!

The Weller Reballing Kit features patented

templates, etched to ensure precise ball

placement. BGA components can be re-

balled to original condition. Used with a

temperature controlled hot air rework tool

or station, the WPRB1000 saves money.


Personal Magnifiers

Reduce Eyestrain—Evaluate Surface FeaturesQuickly, Easily and Accurately WithMag-Eyes Personal Magnifiers.

➊ Feather-lite, only 50 Grams (1.75 oz.)

➋ Magnifier swings up and down, or can be locked in place

➌ Modern open design assures unimpaired vision

➍ Comfortable during long hours of use

➎ Slip-on cushioned headband

➏ For use with long or short hair

➐ Snap-out interchangeable acrylic lenses (2.5X and 4X)

Features� Instantly enlarges images and objects

� Hands-free magnification

� Can be worn with or without eye-glasses, contact lenses or

safety glasses.

� Optical grade acrylic lenses

� Distortion-free viewing

� No Headaches: simple, comfortable

and safe

� Double lens for 3D viewing

� Wide field of vision

� Adjustable lens angle

� One Size Fits All

APPLICATIONS� Electronics

Schematics and Printed Circuit Board

Assembly/Rework

� Manufacturing

Tooling and Prototype Development

� Quality Control

Gauging and Hands-on Parts Inspection

� Dentistry

X-rays, Lab Work

� Manual Trades

Jewelry Work, Watch Repair

� Science

Sample Studies In Geology, Botany and Biology

ESD SAFE

Model 383-AS ESD SAFEFor electronics and clean room environments.The model 383-AS Anti Static Mag-Eyes has all the advanced

features of the model 383, but is specifically designed for work

areas where Electro Static Discharge is to be avoided or when

clean room standards must be met. To comply with these

requirements, the 383-AS is molded from solid-state semi-

conductive material chemically bonded into polymer matrix and

has these qualities:

� Color: black

� Surface resistivity—“Static Dissipative” range: 106–109 ohms/sq.

� Static protection is independent of humidity from 0% to 100%.

� Static resistivity and static decay rate are unaffected by

temperature.

� Static protection is maintained throughout entire life of material.

� Tribo-electric charging < 20 v.

� Contains no amine or amide based volatile additives and will

not contaminate component surfaces.

� Clean room compatible, no sloughing—the particle counts are

substantially below those limits set for Class 10 clean rooms.

� Meets stringent German standards for recyclability.

Order Numbers:

383 (Regular) $31.95383-AS (Anti-Static) $39.95

Each unit is shipped

complete with 2 lenses

(2.5X and 4X) and

instruction sheet.


Adjustable Matrix Trays

Features� Hold any size quadpack or flatpack up to 4" long.

� Plastic supports are molded in PPA with carbon fiber with a

surface resistivity of 10E5-10E7 ohm/ch, are non-sloughing and

tolerate 170C.

� Tray and cover are extruded aluminum, finished in ESD safe,

clear chromate.

� ESD foam with conductive film in the cover for cushioning and

component thickness variations.

� Standard unit measures 6" x 12" x 1" with cover.

� Thumb screws lock the cover to the base.

� Standoffs on each end for easy location and locking to

the cover.

� Patent No. 5,370,225.

Optional Pick and Place Mode� Quads only, must be square.

� Orients devices in accurately registered X–Y positions.

� Interfaces with standard pick and place machines,

e.g. Zevatech, Fuji, Quad, etc.

� Overall length of .400" less cover.

Maximum Capacity For Square Quadpacks

Maximum Body Number of PiecesDimensions Per Row

.580 inches ............ 7

1.026 inches ............ 6

1.480 inches ............ 5

1.875 inches ............ 4

2.125 inches ............ 3

Order Numbers:

Product Order Number PriceBase w/cover for 10 Quadpacks ........................AMT-6x12 QP .......... $185.50

Base w/cover for 10 Flatpacks ...........................AMT-6x12 FP ............. 185.50

Base w/cover for bottom brazed pkgs. ..............AMT-6x12 QP-B ......... 295.00

Base w/cover P&P for automation (QFP) ...........AMT-6x12 QP-A ......... 325.00

Base, no cover, no supports ..............................AMT-B1 ........................ 68.90

Cover only with anti-static foam .........................AMT-C1 ........................ 47.40

Anti-static foam .................................................AMT-A1 .......................... 5.30

Quadpack molded support w/hardware .............AMT-QP ......................... 3.81

Flatpack molded support w/hardware ................AMT-SS .......................... 3.81

NoteCall for quantity price breaks.

Combination tray shown with quadpack

and flatpack supports is for illustration only.


Practical Pen-Vac™ Vacuum Handling Tool� No vacuum hoses or power cords to get

in your way.

� Has rear storage cap.

� Quick change luer lock fitting.

� Made in the U.S.A.

Order Number: V8901-LMS-ESD1-10 11-25

Pricing: $48.75 $47.00

� Fits in your pocket like a pen.

� ESD safe units are supplied with a clear

aluminum finish.

� Perfect for handling surface mount

components.

� Vacuum-cup rubber is ESD safe.

� No batteries to replace.

� Includes two 1/4" cups, two 3/8" cups

and two 1/8" cups.

ESD SAFE

Length146mm (5 3/4")

Quick ChangeLuer Lock Fitting

RearStorage Cap

1/8"

1/4"

3/8"

Cup Size Order Number 1-10 11-25BVJ-038 (3/8" diameter vacuum cup) BVJ-038-B $11.25 $10.70BVJ-050 (1/2" diameter vacuum cup) BVJ-050-B 11.25 10.70BVJ-062 (5/8" diameter vacuum cup) BVJ-062-B 11.45 10.75BVJ-075 (3/4" diameter vacuum cup) BVJ-075-B 11.45 10.75

Practical Bulb-Vac™ Vacuum Handling Tool

ESD SAFE� The Bulb-Vac™ Vacuum Handling Tool is

for the user who needs very little

accuracy when placing parts.

� The entire tool is constructed of ESD

safe materials.

� A needle protrudes out of the plastic tip

to hold the vacuum cup in place.

� This tool is available in four

different styles.

89mm(3.5")

39.6mm(1.56")

92mm(3 5/8")

12.7mm(1/2")

Vacuum Handling Tools

ESD SAFE

Practical Handi-Vac™ Vacuum Handling Tool� An inexpensive tool that no assembler

should be without.

� Replaces tweezers for many

applications.

� ESD safe.

� ESD safe with antistat treatment.

� Selection of four probes with vacuum

cups included.

� Includes one 1/4" cup, one 3/8" cup and

two 1/8" cups.

� Easily handles up to 3–ounce objects.

� Totally self-contained vacuum.


� Can be included in all of your tool kits.

� Good for handling surface mount

components.



Order Number: HV-KIT1–10 11–25

Pricing: $11.25 $10.75


Vacuum Handling Tools

Optional Vacuum

Interrupter for precision

parts placement.

Practical SMD-Vac™-GP Vacuum Handling ToolIs ESD Safe

ESD SAFE

ESD SAFE

� Perfect for pick and place operations.

� Whisper quiet.

� Diaphragm pump provides years of

continuous service.

� All components including vacuum cups

are ESD safe.

� Three-wire power cord.

� Small footprint (3" x 5") consumes

minimal bench space.

� Develops over 5 inches Hg. of vacuum.

� The SMD-VAC™-GP comes with:

● 110 or 220 volt vacuum source.

● Four feet of 1/8" flexible vacuum hose.

● Four feet of 1/8" coiled vacuum hose.

● A set of seven vacuum tips.

● Optional Vacuum Interrupter facili-

tates precision placement of SMT

capacitors, resistors and MCM die.

Order Numbers: V8000 (for 110 volts)V8000-200 (for 200 volts)

1–10 11–25Pricing: $113.00 $119.00

Practical Pac-Vac™ Vacuum Handling ToolFor Portable Operation

� A 9-volt disposable alkaline battery.

� Compact design measures 108mm x

61mm x 22.1mm (approx. 4 1/4" x 2 3/8"

x 7/8").

� Lightweight—only 156 grams.

� Runs up to eight hours

continuously on one 9-volt

alkaline battery.

� Produces vacuum of over ten inches

of mercury.

Practical HP-300™ Vacuum Handling ToolFor Large Components� High-power vacuum tool designed for

large components.

� Perfect for MCM modules and other

heavy components.

� ESD Safe.

� Easily handles up to 500 grams with the

3/4" (19mm) vacuum cup.

� No vacuum hoses or power cords to get

in your way.

� Totally self-contained.

� Fits in your pocket like a pen.



� Perfect for handling large surface mount

components.

� Vacuum-cups push on to a barbed fitting

that holds them tight.

� Vacuum-cup diameters are 1/2"

(12.7mm), 5/8" (15.8mm) and 3/4"

(19mm).


ESD SAFE

The Pack-Vac™ vacuum handling tool is a

battery operated self-contained unit. This

versatile unit can be clipped to your belt for

one-handed portable operation. The Pac-

Vac™ is constructed with ESD safe materials

and comes complete with the

following features:

� A belt clip on the housing.

� Four feet of straight vacuum hose,

#VSH-1/16-4.

� Four feet of coiled vacuum hose,

#VCH-1/16-4.

� A set of seven vacuum tips, #VCS-7-B.

� A vacuum pick-up handle, #V3020-RF.

Order Number: V32001–9 10-24

Pricing: $149.50 $142.03

120mm(4 3/4")

12.7mm(1/2")

Order Number: HP-3001–10 11–25

Pricing: $49.50 $48.00


Tools And Tool Kits

Weller® Soldering Gun Kit(140/100 Watts)� 8-piece kit with 8200 soldering gun

� Includes: one soldering tip; one sealing

tip; one cutting tip; flux brush;

soldering aid tool; coil of lead-free rosin

core solder

� Sturdy plastic carrying case

� Soldering hints booklet

� UL listed

Order Number: 8200PK ..................... $40.00

(260/200 Watts)� 8-piece heavy duty kit with D550

soldering gun

� Includes: one soldering tip; one sealing

tip; one cutting tip; flux brush;

soldering aid tool; coil of lead-free rosin

core solder

� Sturdy plastic carrying case

� Soldering hints booklet

� UL listed

Order Number: D550PK .................... $43.00

Weller® Circuit Board Vise� Complete work center for placing,

soldering and desoldering printed

circuit boards

� Spring clamps hold workpiece in place

� Rotates through 360º, allowing work

performance at any convenient angle

� Adjustable features allow handling of a

variety of circuit board sizes

� Socket key included

� Maximum surface: 6-1/4" x 9-1/8"

(160mm x 235 mm)

� ESD safe

Order Number: ESF120ESD .............. $90.00

Weller® Self-Contained 2-Person Fume Extractor

Xcelite® Pliers Kit—Electronics Handy Pack AssortmentKit Includes:

● EC54J 4-1/2" Transverse end cutting

pliers

● MS54 4" Diagonal cutting pliers

● SN54 5" Long nose pliers with side cutter

● NN54 5" Fine tip needle nose pliers

● DN54G 5" Flat nose pliers

● LN54 5" Long nose pliers

● Pocket pouch with snaps

Order Number: C1K ........................... $89.95

� Efficient 4-stage, replaceable filter

system removes 99.995% of contami-

nants up to 3 microns

� No external air source required

� Silent-running, maintenance-free

rotary pump

� Compact size makes it convenient to

use anywhere

� For use with FE Series soldering irons

� Fully portable

� 120v

Order Number: WFE2P .................... $625.00

ESD SAFE

� A compact kit designed for the sophisti-

cated electronics technician or dedi-

cated hobbyist

� Consists of the six most popular Copaloy

electronics pliers

� Durable pocket-pouch with heavy-duty

snaps

� Each professional quality tool

features the unique Copaloy rivet for

smoother action


A carefully selected, intermediate assortment ofXcelite® hand tools.� Contains 23 individual hand tools, popular WP25 Weller® 25

watt soldering iron, 24 Series 99® interchangeable screwdriver/

nutdriver blades and handles, XL70 offset ratchet screwdriver

set, measuring tape and solder

� Covered with attractive durable tan leather grain Marvelon vinyl

� Removable tool pallet in lid and bottom

� Solid brass hardware and padded handle with anodized

aluminum divider in bottom

� Size: 18" x 12-5/8" x 4-1/4" (457mm x 321mm x 108mm)

Order Number: TC150ST (Tool Case With Tools) ..................................................... $610.50TC150MT (Tool Case Only—No Tools) ............................................ $199.00

Tools And Tool Kits

Xcelite® Attaché Tool Cases For Technicians,Servicemen, And Field Engineers� Choice of sturdy, spacious and attractive attaché style tool cases

� Aluminum tool case plus flexible soft-sided case to meet

virtually every need

� Each contains an ideal assortment and arrangement of top

quality Xcelite® professional hand tools

Largest, most elaborate of tool cases.� Contains 53 individual hand tools, 31 Series 99® interchangeable

screwdriver/nutdriver blades and handles, and two specialized

screwdriver/nutdriver kits

� Covered with attractive durable charcoal brown leather-grain

Marvelon vinyl

� Removable 3-panel hinged tool pallet in lid, plus additional

pallet in bottom

� Solid brass hardware with anodized aluminum divider

in bottom

� Size: 18-3/4" x 12-1/2" x 5-7/8" (476mm x 318mm x 149mm)

Order Number:TC100ST (Tool Case With Tools) ..................................................... $710.50TC100MT (Tool Case Only—No Tools) ............................................ $225.45

A fine blending of quality, economy and flexibility.� Contains 10 individual hand tools and 27 Series 99® interchange-

able screwdriver/nutdriver blades and handles

� Case made from rugged Cordura® and features a heavy-duty

zipper and soft leather-wrapped handles

� Contains (on outside) one pocket on one side and two smaller

pockets on opposite side

� Size: 13-1/2" x 10-1/2" x 2-3/8" (343mm x 267mm x 60mm)

Order Number: TCS200ST (Tool Case With Tools) ................................................... $325.25TCS200MT (Tool Case Only—No Tools) ............................................ $87.95

� Tools neatly mounted in pockets, plus generous space for

individualized selection of test instruments, parts boxes, Weller®

soldering iron, Xcelite® measuring tapes and other tools

� Roomy file pocket in lid for service manuals, circuitry diagrams

and literature


Tools And Tool Kits

Xcelite® Multi-Purpose Tool Kit� 11 quality tools perfect for all types of

routine repair work and simple

D.I.Y. projects

� Packed in an attractive easy-to-store

case

Eram Mutli-Purpose Assembly Kit

Order Number: 3000 KC .................. $315.00

Xcelite® Offset Ratchet Screwdriver Set� 19-piece midget, offset, reversible

ratchet set

� All-purpose driver bits 1/4" (6mm)

hex shank

� Simple and easy-to-use for assembly,

disassembly, adjustment and repair

work involving Allen hex, Phillips and

slotted screws Order Number: XL70 ......................... $53.95

Eram Anti-Static 5-Tweezer andMicro-Cutter Kit

Order Number: 3900 KC .................. $215.00

Xcelite® Personal Computer Repair Kit� Ideal for repairs on PCs

� Contains 12 anti-static chip tools,

protects chips from ESD damage

� Tools fit securely in a convenient

roll-up pouch Order Number: 99SPC-PC ................. $36.95

Order Number: TKX11 ....................... $71.95


Tech Spray 1600

Isopropyl AlcoholLabel & Adhesive Remover

Cleaners/Degreasers, Defluxers, Dusters, Freeze Spray

Order Numbers:1610-P (1 Pint in Plastic) ...................................................................... $6.821610-G (1 Pint in Metal) .................................................................... $32.401610-DSP (48 Pre-Saturated Wipes in Pop-up Container) ................. $10.75

Order Number:1608-DSP (48 Pre-Saturated Wipes in Pop-Up Container) .................... $9.68

Features Benefits� Pre-Saturated Wipe � Quick, Efficient Cleaner

� IPA and DI Water Blend � Controlled Evaporation

� Non-Aggressive � Safe on Most Plastics

� Lint-Free Wipe � Particle Free Cleaning

Isopropyl Alcohol99% pure, anhydrous isopropanol for general purpose cleaning.

Excellent for tape head cleaning, removal of fluxes, light oils, polar

soils and white mineral residue. Can be used as a thinner for

most fluxes.

ApplicationsTape Head Cleaning • Printed Circuit Boards • Connectors

• Microwave and Telephone Circuitry • Data Processing Equip-

ment • Medical Equipment • Relays • Flux Thinner • Fiber Optics

SMT Stencil WipesThis pre-saturated wipe is excellent for removing inks, pastes and

contaminants that usually arise in most SMT processes.

ApplicationsScreens • Stencils • Squeegees • Ceramic and Epoxy Substrates

Features Benefits� 99% Pure Anhydrous Alcohol � Water Free to Prevent Corrosion

� Rapid Evaporation � More Productive Cleaning Agent

� Non-Aggressive � Safe on Most Plastics

� General Purpose Cleaner � Dissolves a Majority of the Soils

Found in the Electronics

Workplace

Label & Adhesive RemoverLabel & Adhesive Remover is a specially designed, hydrocarbon

cleaner that safely removes labels and adhesive gums from

equipment and products. Effectively removes gummy residues,

labels, stickers, ink-marks, beverage spills, and other contami-

nates. Solvent has a pleasant odor.

ApplicationsLabels • Adhesives • Office Equipment • Telephones • Printers

• Copiers • Video Games • CRT Screens • Terminals

• Plastic Cases

Features Benefits� Mild Cleaner � Safe on Most Plastics

� High Flash Point (43°C/111°F) � Reduces Risk of Flammability

� Low Toxicity � Safer Solvent

� Natural Solvent � Non-Ozone Depleting

� Penetrates Rapidly � Efficient Cleaning

� Pleasant Odor � Easy to Use

Order Numbers:1613-6S (6 Ounce Aerosol) ..................................................................$7.931613-6SC (12 Cans Per Case) .......................................................... $85.64


1600 Tech Spray


Ecoline Flux RemoverThe Flux Remover is a unique combination of hydrocarbon

solvents and alcohols making it a excellent defluxer. Safe on

plastics and rapidly evaporating, the Flux Remover dissolves type

R, RMA, SA and most no-clean fluxes. Can also be used as an all-

purpose cleaner for removal of light oils, silicones, waxes, greases

and similar contaminants.

ApplicationsPrinted Circuit Boards • Gold Fingers • Connectors • Microwave

and Telephone Circuitry • Avionics • Relays • Switches

Ecoline Flux Remover Ecoline Contact Cleaner

Order Numbers:1621-10S (10 Ounce Aerosol) .............................................................. $8.621621-10SC (12 Cans Per Case) ........................................................ $93.00

Features Benefits� Contains THF � Excellent Defluxing Power

� Non-Ozone Depleting � Replaces CFCs and HCFCs

� Non-Corrosive � Will Not Harm Metals

� Rapid Evaporation � Efficient Cleaning

� Safe on Plastics � Can Be Used in a Wide Variety

of Applications

Ecoline Contact CleanerGeneral Purpose CleanerThe Contact Cleaner is a hexane mixture that cleans electrical

contacts and connections. Ideal for switches, relays, contact pads

and other electrical connections. Safe on most plastics, the

solvents will not damage switch housings.

ApplicationsContacts and Controls • PCBs • Motors• Generators • Switches

• Industrial Machinery • Gears • Electromechanical Devices


Features Benefits� Hexane Mixture � Excellent Contact Cleaner

� Quickly Penetrates � Efficient Cleaner

� Mild Cleaner � Safe on Most Plastics

� Non-Corrosive � Will Not Harm Metals

Envi-Ro-Tech™ DusterFormulated with HFC-134a, this exceptionally pure, moisture-free,

inert gas removes particles without the use of harmful solvents.

Because HFCs do not harm the ozone, this product has a zero

ozone depletion factor. This product removes microscopic

contaminants, lint, dust, metallic oxide deposits and other soils.

ApplicationsElectronic Equipment • Computers • Printers• Optical Cleaning

• Photographic • Industrial• Film Negatives • Data Processing

Equipment• Laboratory Apparatus • Magnetic Tape Heads


Features Benefits� 100% HFC-134a � Zero Ozone Depletion Potential

� Non-Flammable � No Risk of Combustion

� Leaves No Residue � Contaminant Free

� Moisture-Free � Non-Corrosive

� Non-Abrasive � Safe on Most Plastics

� Oderless � No Irritating Smell

Envi-Ro-Tech Duster


Tech Spray 1600


Envi-Ro-Tech™ FreezerAn HFC134a based, rapidly evaporating liquid that can chill to

minus 62°F. Because HFCs do not harm the ozone, this product

has a zero depletion factor. Used as a troubleshooting aid for

intermittently faulting capacitors, resistors, semiconductors and

other defective components. It also detects cold solder joints,

cracks in printed circuit boards and oxidized junctions.

ApplicationsLocator of Faulty Components • Prevents Cold Solder Joints

• Protects Heat Sensitive Components


Features Benefits� 100% HFC-134a � Zero Ozone Depletion

� Non-Flammable � Less Risk of Combustion

� Chills to -62°F � Quickly Detects Faults

� Leaves No Residue � Will Not Contaminate Substrate

� Moisture-Free � Develops Frost

SMT Stencil Cleaner


Envi-Ro-Tech™ 1676General Purpose DefluxerGeneral Purpose azeotropic defluxer for R, RA, RMA and SA type

fluxes. Can be used as an all-purpose cleaner to remove light oils,

silicones, waxes, greases, and similar contaminants often found in

electronics manufacturing.

ApplicationsPrinted Circuit Boards • Gold Fingers • Connectors • Microwave

and Telephone Circuitry • Avionics • Relays • Switches • Other

Electronic Assemblies

SMT Stencil CleanerHydrocarbon-based, non-ozone depleting stencil cleaner effec-

tively removes solder paste from screens, misprinted boards and

equipment. Its proprietary blend works on most wet or dried thick

film and solder paste compositions. Ideal for hand cleaning

application equipment and misprinted substrates.

ApplicationsCleaning Screen Emulsions • Stencils • Ceramic and Epoxy

Substrates • Most Electronic Components • Application Accesso-

ries such as Squeegees, Spatulas and Mixers

Order Number:1693-DSP (48 Pre-Saturated Wipes in Pop-Up Container) ................. $13.42

Features Benefits� General Purpose Defluxer � Excellent Solvent for

Moderately Polar Soils


� Pure Solvent � Zero Residue

� Penetrates Rapidly � Quickly Dissolves Soils

� Blended HCFC � Removes Ionic Contamination

Features Benefits� Hydrocarbon Based Cleaner � Non-Ozone Depleting

� High Flash Point (43°C/111°F) � Reduces Risk of Flammability

� Excellent Cleaner � Removes Solder Pastes

� Non-Corrosive � Will Not Attack Metal Surfaces

� Completely Evaporates � Efficient Cleaner


1700 Tech Spray

Zero Charge Anti-Stat (Gal.) Zero Charge

Mat & Table Top Cleaner

Zero Charge® Mat and Table Top CleanerA neutral pH cleaner for general use in production areas that

removes insulating contaminants such as flux residues, oils,

greases, nicotine, dirt and grime. The Mat & Table Top Cleaner

eliminates charge while leaving an anti-static agent that helps

prevent static charge build-up.

ApplicationsConductive Mats • Table Tops • Cleanrooms • Computer Stations

• Soldering Stations • Office Equipment • Telecommunications

• Conductive Floor Mats • Electronic Instrumentation

Zero Charge® Anti-StatA fast drying, anti-static coating that eliminates static charge and

reduces triboelectric generation from most surfaces. Recom-

mended for applications that experience flexing and movement

and for plastics such as polyethylene, polypropylene and

polyphenylene oxide (Noryl™).

ApplicationsComputer Cabinets • Printer Covers • Office Equipment • Carpets

• Drapes • Flexible Mats • Walls • Table Tops• Work Stations

• Cloth • Any Application Requiring Static ProtectionOrder Numbers:1726-PT (1 Pint with Trigger in Plastic) ................................................ $9.041726-PTC (12 Cans Per Case) .......................................................... $97.64

Order Numbers:1733-PT (1 Pint with Trigger in Plastic) ................................................ $7.931733-PTC (12 Cans Per Case) .......................................................... $85.64

Features Benefits� All-Purpose Anti-Stat � Can Be Applied to Most Surfaces

� Controls Static � Eliminates Static Charge

� Topical Coating � Reduces Triboelectric

Generation

� Fast Drying � Instant Charge Dissipation


� Easy Application � One Step

Features Benefits� Dual Purpose � Cleans and Provides Static

Protection

� Leaves No Insulating Film � Protects Your ESD Environment

� Non-Abrasive � Will Not Scratch Substrate

� Non-Corrosive � Safe on Plastics


� Contains No Ammonia � Use on Any Surface

Static Control


Tech Spray 1800

Desoldering Braid

No-Clean WickProtective Vacuum Packaging

Tips For Selecting The Right Wick

Important Considerations� Amount of solder involved

� Size of pad or connection

� Desired speed of operation

� Operating temperature

Suggestions� Use a wick equal in diameter to pad and

tip size.

� Use a slightly larger diameter wick if cut

at an angle.

� Use a smaller diameter wick if folded.

Cautions� If the wick size is too large, it will restrict

heat transfers to the connection and

result in reduced wicking action.

� If the wick size is too narrow, it will

require numerous applications to

effectively desolder joint, subjecting the

component and pad to unnecessary

prolonged heat.

SpecificationsMeets or Exceeds MIL-F-142560D, Type R;

NASA NHB 5300.4 (34-1); NASA NPC 200-4;

NASA SP5002.1821: HP 8690-0576; 1822: HP

8690-0588; 1823: HP 8690-0577.

All dimensions are approximate. All

products shipped in vacuum packaging.

Order Numbers:1809-5F ..................................................... $1.701810-5F ..................................................... $1.841811-5F ..................................................... $2.03

1821-5F ..................................................... $2.111822-5F ..................................................... $2.251823-5F ..................................................... $2.48

Wick (Actual Size)#1 White

#2 Yellow

#3 Green

#4 Blue

#5 Brown

#6 Red

nibboBcitatS-itnAkciWorProloC/eziS wolleY/2# neerG/3# eulB/4#

tcudorP 9081 0181 1181

htdiW )mm5.1("060. )mm0.2("58. )mm5.2("001.

ytilibaliavA F01,F5 F01,F5 F01,F5

nibboBcitatS-itnAkciWnaelC-oNroloC/eziS wolleY/2# neerG/3# eulB/4#

tcudorP 1281 2281 3281

htdiW )mm5.1("06. )mm0.2("58. )mm5.2("001.

ytilibaliavA F01,F5 F01,F5 F01,F5


TechPump Bottles: 1980, 1982, 1981

TechPump BottlesTechPump Bottles are designed for precision control and dispens-

ing of solvents in electronic and laboratory environments. The

distinctive pumping mechanism combined with a high density

polyethylene (HDPE) bottle makes a complete unit, ready for use

with a broad range of cleaning solvents. The dish-type pump

dispenser allows for a clean, one-handed operation, which

prevents the use of excessive solvent, and keeps contaminants

from entering the container.

The pump includes a hinged lid to keep out impurities while

the container is not in use, and stainless steel parts to facilitate the

use of aggressive solvents. Precision valve seals contents to reduce

vapor and product loss. To insure total purity, the unit is shipped

with a cellon band sealing the pump head.

Order Numbers:1980 (4 Ounce Bottle with Pump) ....................................................... $11.771981 (6 Ounce Bottle with Pump) ....................................................... $11.941982 (8 Ounce Bottle with Pump) ....................................................... $12.101983 (6 Ounce Conductive Bottle with Pump) .................................... $15.27

1900 Tech Spray

Equipment and Specialty Products

TechSwabs™

Order Numbers:2302-10 (10 Pack Bag) ........................................................................ $3.152302-50 (50 Pack Bag) ........................................................................ $9.872302-1000 (1000 Pack Bag) ........................................................... $123.972300-100 (100 Pack Bag) .................................................................... $2.832300-1000 (1000 Pack Bag) ............................................................. $21.52

2300 Tech Spray

ApplicationsFor use with all Tech Spray cleaners, degreasers and defluxers

• Isopropanol • Ethanol• Mixed Alcohols • Terpenes •Water

Based Solvents

Swab tips are manufactured with a variety of quality materials to

suit different tasks. Most are heat sealed onto handles to avoid the

contaminating residues of adhesives. Handles are fashioned from

a selection of natural and man-made materials chosen for their

flexibility and durability.

TechSwabs™ are packaged in a Class 100 cleanroom in static

dissipative resealable bags that control both electrostatic dis-

charge and contamination. TechSwabs™ are ideal for

cleanroom use.

2302 2300

Tip Width 7/16" 3/16"Attachment of Tip Heat Sealed WrappedHandle Length 6" 6"Handle Material Polypropylene WoodAnti-Static Handle Yes NeutralPliable Handle Yes —


TechClean® SMT Blue WipesSpecifically designed for maintenance, this blue hydroentangled

cellulose/polyester wipe has high absorbency with extra low

particulate and chemical extractables. This wipe has the same

composition as the TechClean® Wiper (2350).

ApplicationsCleanroom Maintenance • Solvent and Aqueous Absorbent

• Dislodgement of heavy Soils • Static Free Environments

Tech Spray 2300

Wipes

TechClean SMT Wipe

TechClean® WiperSpecifically designed for cleanroom maintenance, this hydro-

entangled cellulose/polyester wipe has high absorbency with extra

low particulate and chemical extractables.

ApplicationsCleanroom Maintenance • Solvent and Aqueous Absorbent

• Dislodgment of Heavy Soils • Static Free Environments

Order Number:2350-100 (100 9x9 Inch “C”-Fold Wipes Packaged Bag ‘n’ Bag™) .... $14.57

SpecificationsExceeds U.S. Air Force requirements for surface contamination,

HP 9300-1618.

TechClean® SMT WipeSpecifically designed for cleaning surface mount stencils and

screening equipment. TechClean® SMT Wipe’s cellular based foam

structure traps particulates and liquids for a thorough job. This

wipe is manufactured with polyurethane materials, using a fiber-

free configuration that will not leave wipe particulates behind. Use

with Tech Spray’s SMT Stencil Cleaner (1693) for effective results.

ApplicationsCleaning SMT Stencils • Screens • Squeegees • Mounts

• Misprinted Boards and Components

Order Number:2358-50 (100 6x6 Inch Wipes) .......................................................... $47.50

Order Number:2359-300 (300 9x9 Inch Flat Wipes Packaged Bag ‘n’ Bag™) ............ $23.47


Alloy = A combination of two or more elements whereby at least

one of them is a metal.

Array = A group of elements arranged in rows and columns.

BGA = Ball grid array

BQFP = Bumpered quad flat pack

Castellation = A leadless termination used on LCC packages for

connection to the printed circuit board.

Coplanarity = Related to surface mount, how flat the leads are

referenced to the seating plane.

CQFP = Ceramic quad flat pack

CSBGA = Chip scale BGA

CSP = Chip scale package

DRAM = Dynamic random access memory

Dummy Component = A mechanical package, typically

without the silicon die. Used to verify the manufacturing process

inexpensively.

FC = Flip chip

HASL = Hot air solder leveling

Heatsink = A device that absorbs and drains off heat from hot

objects, re-radiating it into the surrounding environment.

JEDEC = Joint Electronic Device Engineering Council

MCMBGA = Multichip module BGA

MQFP = Metric quad flat pack

LCC = Leadless chip carrier

LPI = Liquid photo imageable

OHM = The unit of resistance

PCMCIA = Personal Computer Memory Card International

Association

PQFP = Plastic quad flat pack

PLCC = Plastic leaded chip carrier

QFP = Quad flat pack

SMD = Surface mount device

SMOBC = Solder mask over bare copper

SMT = Surface mount technology

SMTA = Surface Mount Technology Association

SOIC = Small outline integrated circuit

SOJ = Small outline “J” leads

Solder = A readily meltable alloy of tin and lead used to bond

component connections.

SOP = Small outline package

SSOP = Small shrink outline package

SOT = Small outline transistor

TAB = Tape automated bonding using tape for leads rather than

bonded gold wire.

TQFP = Thin quad flat pack

TSOP = Thin small outline package

TSSOP = Thin, Shrink Small Outline Package

Glossary

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

____________________________________________________________________________________________________

PRACTICALCOMPONENTS

Practical Components, Inc.15211 Springdale StreetHuntington Beach, CA 92649Phone: 1-714-899-8309Fax: 1-714-899-8599Email: [email protected]

Fax Quote Form

Name ________________________________________________

Title _________________________________________________

Company_____________________________________________

Address ______________________________________________

_____________________________________________________

City __________________________________________________

State _______________________________ ZIP ______________

Country ______________________________________________

Phone ____________________________ Ext _______________

Fax __________________________________________________

Email ________________________________________________

Credit Card

□ Visa □ MasterCard □ American Express

Card# _______________________________________________

Exp. Date ____/____

Signature _____________________________________________

Part Number Package Type Quantity Target Price

Delivery Due Date____________________ □ For Purchase Within 30 Days □ For Bid Only

Comments ____________________________________________________________________________________________________

______________________________________________________________________________________________________________

______________________________________________________________________________________________________________

______________________________________________________________________________________________________________

Welcome to Practical Components · 2006. 3. 3. · LQFP Low Profile Quad Flat Pack ..... 21 QFN...

Documents

Transcript of Welcome to Practical Components · 2006. 3. 3. · LQFP Low Profile Quad Flat Pack ..... 21 QFN...