WCDMA Test Guidelines.docx
-
Upload
depeoplearsenal7569 -
Category
Documents
-
view
222 -
download
0
Transcript of WCDMA Test Guidelines.docx
7/27/2019 WCDMA Test Guidelines.docx
http://slidepdf.com/reader/full/wcdma-test-guidelinesdocx 1/2
WCDMA TestGuidelines
1. The WCDMA SSV test include:
A: Mobility test B: Handover(3G->2G)test C: Static test(Pointing test)
2.
Mobility test
A: You should lock all the Scrambling Code of the target site in TEMS.
B: Test route
Road site 1 Road site 2 City site
City site: Ensure you are close to the site before you start the test and make
sure that the radius for the test is about 1km.
3. Handover(3G->2G)test
In the Dedicated mode (WCDMA), make the signal bad, then it will perform
hard handover to GSM.
4. Static test
A: Voice test: Lock the Scrambling Code of target cell
B: Video test: Lock the Scrambling Code of target cell
C: R99 test (DL&UL): Lock the Scrambling Code of target cell and lock the R99 in
TEMS·
D: HSPDA and HSUPA test: You cannot lock the Scrambling Code of target cell
while using the modem, so you must ensure that you are directly under the
sector which is to be tested so that the Modem can camp on the target cell
steadily.
5. Name rule:
Mobility test: DT_2011031216_B1202_Mobility_MS1 for Voice_MS2 for
HSDPA_Long callHandover (3G->2G)test: DT_2011031216_B1202_Mobility_InterRAT Handover
Voice test: DT_2011031216_B1202_Sect1_Static_Voice_Short call
Video test: DT_2011031216_B1202_Sect1_Static_VP_Short call
R99 DL test: DT_2011031216_B1202_Sect1_Static_R99_DL
R99 UL test: DT_2011031216_B1202_Sect1_Static_R99_UL
HSDPA test: DT_2011031216_B1202_Sect1_Static_HSDPA_DL
HSUPA test: DT_2011031216_B1202_Sect1_Static_HSUPA_UL
6. SSV Report:
FOR CS
A: Export the logfile (Mobility test choosing MS1 for Voice) from TEMS to Mapinfo
7/27/2019 WCDMA Test Guidelines.docx
http://slidepdf.com/reader/full/wcdma-test-guidelinesdocx 2/2
The KPIs needed for this export are:AS CPICH EcNo; AS CPICH RSCP;UE Tx Power;
AS SC;AS No of Member
FOR PS
B:Export the logfile(Mobility test choosing MS2 for HSDPA) to Mapinfo
The KPIs needed for the export are:HS-DSCH Throughput; AS CPICH EcNo;
ASCPICH RSCP; UE Tx Power; AS SC; AS No of Member
FOR EVENT
C: Export the logfiles(All of the logfiles for this site) to Mapinfo, and then get the
Event number from the Mapinfo. Below is the Event statistics (SSV report->test
Summary) which can get from the Mainfo Event stat.
Cell Addition 1A Radio Link Additon
Cell Removal 1B Radio Link Removal
Cell Replacement 1C Radio Link Replacment
RRC Setup Count
RRC Established+RRC Connection Abnormal Release+RRC
Connection Reject
RRC Setup Suc Count RRC Established
RRC Setup Suc RatioRRC Established/(RRC Established+RRC Connection Abnormal
Release+RRC Connection Reject)*100
Average Setup Time Delay (ms) 100
Total Number of Calls Call Attempt
Total Successful Call Setup Call Established
Total Access Failures Call Attempt-Call Established
Total Drops Dropped Call
Total Completed Calls Call End
Drops Call Rate (%) Dropped Call/Call Established*100
Call Setup Success Rate (%) Call Established/Call Attempt*100
Number of IntraFreqHHOFail Intra-frequency Hard Handover Failure
Number of IntraFreqHHOSuc Intra-frequency Hard Handover
R99 IntraFreq HHO Success Rate (%)(Intra-frequency Hard Handover-Intra-frequency Hard
Handover Failure)/Intra-frequency Hard Handover*100
Number of InterFreqHHOFail Inter-frequency Handover Failure
Number of InterFreqHHOSuc Inter-frequency Handover
R99 InterFreq HHO Success Rate (%)(Inter-frequency Handover-Inter-frequency Handover
Failure)/Inter-frequency Handover*100
Handover From UTRAN (3G->2G) Handover From UTRAN
Cell Change Order From UTRAN
Failure (3G->2G)
Cell Change Order From UTRAN Failure/Handover From
UTRAN*100
Cell Change Order From UTRAN
Success Rate (%) (3G->2G)
(Handover From UTRAN-Cell Change Order From UTRAN
Failure)/Handover From UTRAN*100
Location Area Update Location Area Update
Location Area Update Failure Location Area Update Failure
Location Area Update Failure Rate (%) Location Area Update Failure/Location Area Update*100