Wayside Inspector...Model A81000 Wayside Inpector shown for reference purposes only! Actual unit...
2
Model A81000 Wayside Inpector shown for reference purposes only! Actual unit selected may vary in mounting and features. SIEMENS Wayside Inspector Automated Grade Crossing Testing System automates periodic inspection of crossings such as monitoring the state of discrete I/O signals, battery voltages and AC power. From that information, it analyzes the operation of the grade crossing’s warning systems and provides a means for inspection of those systems. It can send alarms and inspection report logs to a backoffice system or can interact thru a WebUI to allow field personnel to adjust system settings, view statuses etc. Overview ● Scheduled Annual Warning Time inspection available for both main and standby equipment, and for every directional approach and route through associated crossing. (When used in conjunction with optional WiMag® sensor and specific setup procedures) (Railroad personal must verify warning time) Scheduled Monthly Standby Power inspection available. ● Scheduled Monthly Ground inspection available. ● (When used in conjunction with optional Ground Fault Tester - GFT II and specific setup procedures) All inspections can be tailored to meet individual railroad ● threshold requirements. Features Reference to any specific commercial products, processes, or services, or the use of any trade, firm, or corporation name is for the information and convenience of the public and does not constitute endorsement, recommendation, or favoring by their respective entities usa.siemens.com/rail-automation Wayside Inspector Automated Grade Crossing Testing System 8 9 10 11 12 13 14 - 15 16 1718 19 20 21 - 22 - 23 - 24 - 25 - TX/RX Comms Alarms Suppressed Health Power 1 2 3 4 5 6 7 - On-Site Personnel 1 2 3 - - - - - - - - - Digital Inputs Battery Inputs B H F B H F B H F B H F Relay Outputs AC CTRL Relay F H Line In Neutral 110/220 VAC Isolated 12VDC (0.5A) OUT - - - Wayside Inspector 81000 Network Laptop Comms DANGER HIGH VOLTAGE B N 22YUU 4 3 2 1
Transcript of Wayside Inspector...Model A81000 Wayside Inpector shown for reference purposes only! Actual unit...
Model A81000 Wayside Inpector shown for reference purposes only! Actual unit selected may vary in mounting and features.
SIEMENS Wayside Inspector Automated Grade Crossing Testing System automates periodic inspection of crossings such as monitoring the state of discrete I/O signals, battery voltages and AC power.
From that information, it analyzes the operation of thegrade crossing’s warning systems and provides a meansfor inspection of those systems.
It can send alarms and inspection report logs to a backofficesystem or can interact thru a WebUI to allow field personnel to adjust system settings, view statuses etc.
Overview
● Scheduled Annual Warning Time inspection available for both main and standby equipment, and for every directional approach and route through associated crossing. (When used in conjunction with optional WiMag® sensor and specific setup procedures) (Railroad personal must verify warning time)
Scheduled Monthly Standby Power inspection available.●
Scheduled Monthly Ground inspection available.● (When used in conjunction with optional Ground Fault Tester - GFT II and specific setup procedures)
All inspections can be tailored to meet individual railroad ● threshold requirements.
Features
Reference to any specific commercial products, processes, or services, or the use of anytrade, firm, or corporation name is for the information and convenience of the public and does not constitute endorsement, recommendation, or favoring by their respective entities
usa.siemens.com/rail-automation
Wayside Inspector
Automated Grade Crossing Testing System
8 9 10 11 12 13 14 - 15 16 1718 19 20 21 - 22 - 23 - 24 - 25 -
TX/RX Comms
Alarms Suppressed
Health
Power
1 2 3 4 5 6 7 -
On-Site Personnel
1 2 3--- --- ---
Digital Inputs
Battery Inputs
B
H
F
B
H
F
B
H
F
B
H
F
RelayOutputs
AC CTRL RelayF
H
Line In
Neutral110/220 VAC
Isolated12VDC (0.5A)
OUT
---
Wayside Inspector81000
Network Laptop
Comms
DANGER
HIGHVOLTAGE
B N
22YUU
4
3
2
1
Wayside Inspector(Part No. NYK:8000810000001)Physical Data
Series Designation
Height
Dimensions:
▼Specification ▼Models
10.00 in (25.40 cm)
Width 19.00 in (48.26 cm)
Depth 2.00 in (5.08 cm)
Weight: 9.44 lbs (4.28 kgs)
General Data
Series Designation ALL Models
Digital input(s)
Analog battery input(s)
AC Power Control Relay(s)
AC Power Monitor Input(s)
Power Output(s)
General Purpose Relay Output(s)
Laptop Network Interface Ports
Communications Network
Interface Ports
Communications
Serial ports
External Configuration Device (ECD) Ports
Expansion Card Slots
▼Specification ▼Models
25 (also supports Ground Fault Tester (GFT II) serial data)
Ordering
To Order:Call: 1 (800) 793 7233
Specify:
● Part Number
SIEMENS Industry Inc.Mobility, Rail Automation2400 Nelson Miller ParkwayLouisville, KY 40223
SIE-MO-RA-PFBR-WAYINSPEC-17-ENUnrestricted ReleasePrinted copies are uncontrolledSubject to modifications
© SIEMENS Industry Inc. 2017
A81000 Wayside Inspector
Operating Temperature: -40° to +160° F (-40° to +70° C)
Humidity (Maximum) 90% non-condensing
Environmental Data
Series Designation ALL Models
▼Specification ▼Models
4 (1 for supply power, 3 additional)
1
1
1(Isolated, for Communications Equipment)
4
1
1
1
1
1
1
WiMag® Standard Vehicle Sensor (Required for some tests)(Part No. NYK:Z921004070000)
WiMag® Standard Repeater (Optional)(Part No. NYK:Z921004070000)
Access Point Base Station (Optional)(Part No. NYK:Z927004210000)
Made in USA A81010-01
GROUND FAULT TESTER II
FOR 9V TO 16.5V BATTERIES
SIEMENS
FAILGFT
PWRBAT 2BAT 1
FAULT FAULT
SE
L 0
SE
L 1
SE
L 2
SE
L 3
See user manual forcurrent mode selection.ON
OFF
NC
NC
BA
T 1
BA
T 1
RLY
2 C
OM
RLY
1 N
O
RLY
1 C
OM
RLY
2 N
O
D O
UT
TE
ST
B N BA
T 2
BA
T 2
E G
ND
1
E G
ND
2
J1 J2
Ground Fault Tester - GFT II (Optional)(Part No. NYK:8000810100001) 9V - 16.5V version
