USEFUL FOR:

� Basements

� Cellars

� Foundations

� Below Grade Walls

� Cisterns

� ICF

� Plywood

� Concrete

Elastic!

Adhesive!

Impervious!

Manufactured by Ames Research Laboratories, Inc.1891 16th St. SE Salem, OR 97302

Ames’® Blue Max® is a trademark of Ames Research Laboratories, Inc. Copyright ©2019 by Ames Research Laboratories, Inc. All illustrations, photographs, diagrams and written content are property of Ames Research Laboratories, Inc. All Rights Reserved. 032119

Maximum Waterproofer

®®‘Ames

VOC less

than

25g/liter

Find Blue Max®

On Our Website

Ames Research Laboratories, Inc. is a green

manufacturer of premium grade, elastomeric

coatings, sealants, and paints for

waterproofing roofs, walls, decks, basements,

and many other surfaces. We are experts with

over 30 years of experience in waterproofing.

Our impervious coatings are the highest

quality on the market today. All products are

water-based, water clean-up, and contain no

harmful petroleum or silicone.Blue Max® Regular GradeBasement & Foundations

Waterproofer

Features:� High Strength Liquid Rubber� High in solids � Water-based� Water clean up� Easy application� Pour out and rolled, brushed, or sprayed.

Benefits:� Flows into cracks and crevices as a liquid and sets up as a durable rubber to seal leaks.� Expands and contracts to resist cracking and peeling� Creates and impervious membrane� For Extreme waterproofing situations� Up to 1200% Elastomeric

Waterproofing

that really works!

1-888-345-0809www.amesresearch.com

Veteran Owned Business

Estimated CoverageStandard product coverage on a smooth surface is 100 sq. ft. per gallon per coat (est. 10 mil). More than one coat recommended. More coats equal longer life. Rough surfaces will require additional product and drying time.

3. ApplicationApply Blue Max to the surface using a standard paint roller at the rate of 1 gallon per 100 sq. ft. per coat. We recommend 2 coats minimum or 3 coats for water tanks and cisterns. Blue Max is an elastomeric, and therefore dries slightly tacky. It may be top-coated on roofs with Maximum-Stretch®, and on basement walls with Block & Wall® or Paint & Prime®. When used on roof decks, Blue Max is top coated with Safe-T-Deck®. Blue Max needs to be top coated in applications with direct sun contact to protect from UV degradation. Applications below ground, such as ICF (insulated concrete forms) and water tanks or cisterns do not need to be top coated.

1. Surface PreparationWire brush any loose flaking material off the surface, and remove any dust or particles. Caulk all cracks greater than 1/8" wide with Ames’ Blue Max Trowel Grade and allow to dry. Always run a test patch first, in an inconspicuous area, to ensure proper adhesion and drying, and that the product performs to your satisfaction. Be sure that surface is clean and dry before applying the coating. Do not use any soaps or detergents to clean surface.

2. Prime & Seam TapePrime all inside 90° angles and joints with Blue Max Regular Grade, and let dry. Apply Ames’ Peel & Stick Seam Tape™ to primed areas. Repeat steps with any other cracks or joints on surface. Ames’ Peel & Stick™ Seam Tape is available in 2”(PS250), 4” (PS450) , and 6” (PS650) widths. (See Seam Tape label for instructions.) Apply a liberal topcoat of Blue Max over the Seam Tape and allow to cure. Blue Max is self-priming.

Stop Leaks in 3 Easy StepsTo learn more application tips visit www.amesresearch.com

Scissors or Utility Knife

3”-4” Wide Paint Brush

Ames Peel & Stick Seam Tape

Low Nap Roller & Handle

TrowelCommercial Airless Spray

©2019

1 Gal = 100 Sq. Ft.

10’

10’

Application ToolsYou may need one or more of the following:

Adhesive Strength: 80 PSIBlue Max has been testedup to 35 ft under water