Warthog Mount assembly instructions mount assembly instructions_nov2018.pdfWarthog Stick Assembly:...
Transcript of Warthog Mount assembly instructions mount assembly instructions_nov2018.pdfWarthog Stick Assembly:...
Warthog Mount assembly instructions
1 24
3
5
6
6
7
8 910
Item # Qty Description
1 1 Throttle Vertical Assembly
2 1 Warthog Throttle Assembly
3 1 Warthog Stick Assembly
4 1 Stick Horizontal Assembly
5 4 Anchor Mounts
6 4 WH Throttle Hardware
7 4 WH Stick Hardware
8 2 End Cap Plate
9 4 Push-In Retainers
10 1 5/32” Ball End Hex Key
What’s Included in the Box:
Vertical Assembly Overview:
Rotate the Toggle Clamp Lever to toggle between the unlocked and locked positions
For small adjustments in clamping distance, rotate the leveling
foot, and secure with the locking nut
For larger adjustments, use the included Hex Key to loosen
the two screws holding the Toggle Clamp, and shift up and down as needed. It should only take a turn or so to loosen. Tighten firmly when done.
Leveling Foot Locking
Nut
Vertical Assembly Overview:
Test fit the Vertical Assembly on your desk. Adjust the clamp as necessary to make a firm and secure hold. A tip for this is to screw the leveling foot fully into the shaft, flip the clamp in the upward position, loosen the two screws securing the clamp, then slide it up to touch your desk. Next, tighten the two screws holding the clamp fully tight. Then unscrew the leveling foot a few turns so that it makes a firm hold on your desk. You may need to toggle the clamp to unscrew, then latch again. Repeat this process for both vertical assemblies.
CAUTION
This clamp can exert hundreds of
pounds of force. Be careful not to
overtighten the clamp or you might
cause damage to your desk.
Keep fingers, limbs, and electrical
cords away from the leveling foot
when toggling the clamp.
!
Warthog Stick Assembly:
The Warthog stick assembly mounts to the Vertical Assembly using two anchor fasteners. The stick plate can be
adjusted forward and backward 0-3”.Adjustment is made by loosening the two button head, and two flat head screws, sliding to the desired position, then tightening again. These are tightened for shipping, but it should only take a
turn or two to loosen.
To make future adjustment easier, you may wish to leave the two flat head screws in the center of the plate slightly loose. This will allow you to adjust the stick forward and backward without removing it. To do this, loosen all 4 screws until you can slide the plate freely. Then
tighten the two flat head screws until it takes some force to slide the plate, and you can’t lift
it up. Slide to the desired position, then tighten the two button head screws at the front.
Mounting the Stick Assembly to the Vertical Assembly
Mount the vertical assembly to your desk, then hold the stick assembly at the height you desire. Remember this location or mark it with a piece of tape. Being exact isn’t important, it’s just to get you in the ballpark for future adjustment. Once you have the height in mind, set the stick assembly aside, and
mount the vertical assembly upside down on your desk.
Take an Anchor Assembly and loosen the nut on it such that only a few threads are engaged. Then slide it into the left slot as shown.
Repeat for the right Slot.
Mounting the Stick Assembly to the Vertical Assembly
Position the Throttle Horizontal Assembly below the two anchors, then slide it upwards, and guide the
anchors into the pockets in the rail as shown. Raise to approximately the desired height
Use the Ball End of the included 5/32” Hex Key to snug up the two anchor bolts. Then use the short
end for more leverage to snug them down extra tight. Take care to ensure that the horizontal beam is rotated level when tightening.
Afterwards you can install the push in fasteners.
Mounting the Stick To the Stick Assembly
Use the included M4 Screws to mount the stick to the Stick Assembly. You will need a Phillip’s head screwdriver for this. Once done, rotate the mount right side up and give it a feel. Adjust the height, and horizonal position as needed for optimal comfort
Throttle Assembly
Assemble the Throttle Assembly onto its Vertical Assembly using the same procedure as the stick
Rotate the mount right side up, and place the throttle on top. Align the throttle holes with the holes in the mount, and use the included screws and nuts to secure. You will need an adjustable wrench for this. The nuts may take a little force to screw on due to the locking feature. It is up to the user whether they want the nut on top or on bottom, either way works.
All Done, Enjoy!