WARP9 LED - CNR Lighting

KIM LIGHTING 1Lenis eumsan esent lutat lam

SITE/ROADWAY

WARP9

The Next Generation of LED Site and Street Lighting

WARP9® LED


Kim Lighting is known throughout the world as the premier designer and manufacturer of quality, high performance, and architecturally relevant outdoor lighting solutions. Kim Lighting is a division of Hubbell Lighting, Inc.

Contents:LED Glare Guard Technology 2

Amazing Distribution Capabilities 5

LED Uniformity Perfected 7

Upgradable EmitterDeckTM 9

Enhanced Green Footprint 10

Light Pollution Reduction 11

Advanced Technology Exclusives 14

Visual Stealth Features 16

Installation and Maintenance 18

Ordering 20

Specifications 22

LM-79 Compliance 23

Photometry and BUG Ratings 24

Warranty 29

IP66RATING

MADEUSA

INThE


Glare, no. Brilliant, yes. The promise of LEDs has finally been realized without compromising visual comfort…Now is the time for WARP9 LED, the newest innovation in high tech street and area lighting from Kim Lighting. By controlling powerful solid-state sources with advanced reflector dynamics, WARP9 LED harnesses the enormous brightness from the latest diode technology to collect and widely distribute light precisely and efficiently without objectionable glare or hot spots. Combine this with a rugged, visually stealth housing, an upgradeable LED module, and progressive warranty protection, WARP9 LED is the modern, energy efficient, truly sustainable LED lighting solution that will serve your community for decades. With Kim Lighting’s WARP9 LED, the future of site and street lighting has arrived.

This is LED lighting perfection. This is Kim Lighting.

KIM LIGHTING 1

The Only Low Glare LED Solution

WARP9 LED - Up to 50% less glare Competitor's LED Luminaire

70°

70°

When located outside the illuminated zone, the viewer’s eye is always in WARP9-LED’s glare-free zone.

When located within the illuminated zone, the viewer’s normal field of vision never includes all of the luminaire’s source.

The 140-70 PrincipleThe normal human field of vision is approximately 140°. By maintaining a sharp 70° cutoff, WARP9-LED achieves the optimum angle to block glare and still maintain wide pole spacings. In addition, even if the viewer does look toward the luminaire, half of WARP9’s reflector controlled LEDs are directed away from the viewer, automatically reducing glare by nearly 50% compared to other manufacturer’s refracted or lensed LED systems. The result is broad, uniform ground plane illumination and superior visual comfort.

Premium Comfort and Safety

KIM LIGHTING 2

WARP9 LED is the first outdoor area light to utilize LEDs properly and safely to effectively capitalize on the incredible efficiency, life, and brightness of Solid State Lighting technology. Just because LEDs are the wave of the future does not mean that designers should abandon the important safety practices and performance standards established by the industry over decades of study and refinement. Rather, WARP9 LED meets or exceeds currently adopted international outdoor lighting codes to maintain existing pole spacings, extinguish backlight pollution, completely cutoff uplight, and eliminate harmful glare which can significantly improve citizen safety.

Full Cutoff, Zero Uplight

Full Cutoff, Zero Uplight

Glare-Free Zone

Glare-Free Zone

LED’S RECESSED INTO FIXTURE HOUSING

Canted MicroEmitterTM Design Each WARP9 LED board and reflector cap is precisely aimed at optimal angles for maximum reach and uniform illumination.See page 4 for more details.

PATENT PENDING

Deeply Regressed SourcesSince WARP9’s LEDs are tightly controlled with reflectors, it was not necessary to place them at the lens plane to maximize efficiency. Glare and high angle brightness is significantly reduced.

Glare Guard Perimeter ReflectorWARP9 LED uses a secondary perimeter reflector system to capture miniscule stray light above 70° and redirect it towards the intended ground plane target. These reflector surfaces are precisely engineered to increase efficiency and visual comfort at normal viewing angles, and feature imported Miro4

® 95% reflective surfaces.

The Only Low Glare LED Solution Exclusive Optical Technology

70°

70°

When located outside the illuminated zone, the viewer’s eye is always in WARP9-LED’s glare-free zone.

When located within the illuminated zone, the viewer’s normal field of vision never includes all of the luminaire’s source.

The 140-70 PrincipleThe normal human field of vision is approximately 140°. By maintaining a sharp 70° cutoff, WARP9-LED achieves the optimum angle to block glare and still maintain wide pole spacings. In addition, even if the viewer does look toward the luminaire, half of WARP9’s reflector controlled LEDs are directed away from the viewer, automatically reducing glare by nearly 50% compared to other manufacturer’s refracted or lensed LED systems. The result is broad, uniform ground plane illumination and superior visual comfort.

The 70° Principle

KIM LIGHTING 3

By maintaining a sharp 70° angle, WARP9 LED achieves the optimum cutoff to block glare and still maintain wide pole spacings. In addition, even if the viewer does look toward the luminaire, half of WARP9’s reflector controlled LEDs are directed away from the viewer, automatically reducing glare by nearly 50% compared to other manufacturer’s refracted or lensed LED systems. The result is broad, uniform ground plane illumination and superior visual comfort.

Miro4 is a registered trademark owned by Alanod.

Kim Lighting has always been known for its expertise in optical design and advanced reflector engineering, and has applied that knowledge in WARP9 LEDs patent pending MicroEmitter design.

EmitterDeck

Carrier Plates

EmitterDeck

Quick-Connect

Reflector Cap

Thermal Junction Monitor

(3) Diodes

Replaceable MicroEmitter and Heat Sink Assembly

Plug and Play Connector

Redirected Side-Candela

Redirected Side-Candela

Targeted, precisely controlled LED illumination

UnimpededMain Beam

MicroEmitterTM

Reflector Modules

Essentially miniature luminaires, a replaceable MicroEmitter

consists of a circuit board of three LEDs individually controlled by a hollow cap reflector. This efficient design leaves each diode’s main beam candlepower unencumbered while amplifying and redirecting any LED spill light. Each MicroEmitter is mounted in the WARP9 LED EmitterDeck, which is deeply recessed into the housing. Each MicroEmmiter is aimed to widely spread uniform illumination onto the ground plane while maintaining a sharp 70° cutoff. A secondary perimeter reflector blocks and redistributes any stray light out of the high angle zone to achieve a truly glare-free appearance. The result is comfortable, powerful, and properly shielded LED sources that only place light where intended, without the use of blinding, inefficient and ineffective refractive media.

Maximizing Main Beam Candlepower

KIM LIGHTING 4

MicroEmitter Reflector Module

Replaceable EmitterDeck LED Array

Interchangeable MicroEmitters

PATENT PENDING

Achieve any IES distribution, as well as new unique and custom distributions, with the incredible flexibility of Kim Lighting’s MicroEmitter modules within each removable WARP9 LED EmitterDeck assembly. Because each of WARP9’s LED boards is optically controlled separately, designers have the ultimate in flexibility to shape, direct, and distribute light precisely…and only where it is desired.

Imagine Any Distribution with WARP9 LED EmitterDeckTM Arrays

Type II Type III Type IV Type VFor narrow roads or

residential on 20' poles, 4 mounting heights apart.

For double lane roads with two-way traffic on 20' poles,

4 mounting heights apart, staggered on both sides

of the street.

For parking lot perimeter areas with two-way traffic on 20' poles, 2.5 mounting

heights apart.

For parking lot interior areas with lighting desired

in all directions on 20' poles, 2.5 mounting heights apart. With multiple fixtures on a

pole, use Type III.

Amazing Distribution CapabilitiesMicroEmitterTM

Reflector Modules

Wrap light around an odd intersection. Block light at the neighbor’s fence. Maintain existing pole spacings. Even direct all light glare-free in one direction for a downtown boulevard or a regional light rail system. The possibilities are infinite, and only attainable with Kim Lighting’s patent pending WARP9 LED technology.

Unique One-Way Distributions

Type L Type R

KIM LIGHTING 5

NoGlareZone

NoGlareZone70° 70°

WARP9 LED One-Way Distribution

.5 .5 .5.8 .8 .8 .8 .8 .8

.4 .4 .4.8 .5 .8 .8 .5 .8

.4 .4 .4.6 .3 .6 .6 .3 .6

25�' �

25�' �

25�' �

WARP9 LED is perfect for street lighting upgrade projects because communities can safely utilize existing pole installations and still maintain uniform illumination between luminaires. Compare WARP9 LED’s low max-to-min uniformity ratio to other LED systems, and the difference is clear.

Maintain Existing Pole Spacings

* Readings at one mounting height forward.

Footcandles*

Footcandles*

Footcandles*

Broad, Even Distribution

WARP9 LED’s unique point-and-shoot approach to area lighting allows for wide, uniform illumination without hot spots, and eliminates the bright pool of light beneath the luminaire compared to traditional inverted LED-bar fixtures.

Perfect For Upgrade and Modernization Projects

KIM LIGHTING 6

Catalog Number Typical Luminaire Wattage

AverageFootcandles

MaximumFootcandles

MinimumFootcandles

Average to Minimum

Ratio

Maximum to Minimum Ratio

WP9LE3/L5K 175 1.51 2.11 1.01 1.49:1 2.09:1

TYPEIII/150PMH 185 1.98 2.96 .89 2.22:1 3.33:1

TYPEIII/200PMH 240 3.33 4.98 1.51 2.21:1 3.30:1

TYPEIII/250PMH 291 3.66 5.48 1.66 2.21:1 3.30:1

TYPEIII/150HPS 188 2.80 4.32 1.34 2.09:1 3.22:1

TYPEIII/200HPS 240 3.85 5.95 1.84 2.09:1 3.23:1

TYPEIII/250HPS 295 4.90 7.57 2.34 2.09:1 3.24:1

Criteria: Mounting height is 20', on a street width of 50', and spacing is 95' apart. Mean Lumens and photopic equipment was used for this data.

100' Spacing

120' Spacing

160' Spacing

.5 .5 .5.8 .8 .8 .8 .8 .8

.4 .4 .4.8 .5 .8 .8 .5 .8

.4 .4 .4.6 .3 .6 .6 .3 .6

25�' �

25�' �

25�' �

Broad, Even Distribution

WARP9 LED eliminates the staccato of glare and hot spots experienced by drive lane users as they travel through illuminated zones. Other LED systems cannot achieve WARP9’s wide 70° reach. Unfortunately, other optically compromised products create a striped-street strobe effect with alternating regions of extreme brightness and darkness. The resultant human experience is annoying at best, but can be potentially hazardous under certain conditions.

3 .20 0.2

Avoid Nadir Dump

KIM LIGHTING 7

Nadir DumpZoneD

AR

K Z

ON

E

DA

RK

ZO

NE

Nadir DumpZone

60°

Footcandles are at one mounting height forward

Competitor LED Distribution Maximum to Minimum Ratio = (5:2 Poor)

WARP9 LED Urban Streetscape

The Only Sustainable LED Solution

Now, upgrading your LEDs can be as simple as changing a bulb.

Think of it like a personal computer system. The WARP9 housing is the hardware, and its easily replaceable EmitterDeck™ LED array module is the software. As LED technology improves and becomes even more efficient, WARP9 LED’s upgradeable, sustainable solution will meet the needs of your community today and in the future. When compared to a standard throwaway fixture which can only remain installed as long as its LED life, WARP9 LED is the obvious choice over time. Communities can also take advantage of the newest advances in LED technology as they become available, without the added expense of removing and replacing an entire housing.

Invest in an Upgradeable LED System

KIM LIGHTING 8

Specify WARP9 today for your community’s sustainable tomorrow.”

”

Kim Lighting’s goal is to be more than just your lighting equipmentsupplier. We can be an integral partner with your community to builda truly sustainable lighting solution for future generations to enjoy. Kim Lighting also offers a unique +1 Guarantee program. Any WARP9 LED housing that is upgraded or retrofitted with a new Kim Lighting LED module will enjoy an additional 1-year housing warranty regardless of its installation age, free of charge!1

The Only Sustainable LED Solution Kim Lighting’s Exclusive PlusOneTM

Guarantee

Quick-Connect Wiring with Retrofittable EmitterDeckTM

KIM LIGHTING 9

Specify WARP9 today for your community’s sustainable tomorrow.”

1 Certain conditions apply.

An investment in WARP9 now provides assurance that it will be the right solution for the future. Now that’s sustainability you can count on.

Ownership Comparison Years of System Ownership:

Disposable Non-Upgradeable LED System

LED Warranty Coverage

Housing Warranty Coverage

State-of-the-Art Technology Installed?

WARP9 Upgradeable LED System

LED Warranty Coverage

Housing Warranty Coverage

State-of-the-Art Technology Installed?

1 2 3 4 5 6 7 8 9 10 11 12

Notes and Assumptions: • LED Warranty Coverage: Assumes 11 hours operation per day. • Housing Warranty Coverage: Kim’s PlusOne Guarantee restarts housing warranty for one year upon LED Upgrade.

NewestTechnology

NewestTechnology

•

•

•

•

•

•

•

•

•

•

• • •

• •

•

• •

•

•

•

•

•

•

• •

•

•

•

• •

• •

•

• •

• NewestTechnology

6 YearsWithoutWarranty

6 Years OldTechnology

TotalWarrantyCoverage

Always NewTechnology

NewestUpgrade

NewestUpgrade

RestartWarranty

RestartWarranty

PlusOne

6 Year Out-of-Date Technology Gap

6 Year Warranty Gap

Quick and EasyThe entire assembly fastens to the housing as a one-piece module and features wiring quick-connects for easy upgrading.

DOE/Energy Star SSL Quality Advocate

KIM LIGHTING 10

Kim Lighting is proud to be an official Energy Star Partner and Department of Energy SSL Quality Advocate. The SSL Quality Advocate program is a voluntary pledge that seeks truth in advertising by introducing the Lighting Facts™ label, similar to the Food and Drug Administration (FDA) Nutrition Facts label. The Lighting Facts label provides a quick and simple summary of product performance data as measured by the new industry standard for testing photometric performance, IESNA LM-79-2008. Contact Kim Lighting for the Warp9 LED Lighting Facts label.

All of Kim Lighting’s WARP9 LED photometry and LEDs will be tested and third-party verified under LM-79 and LM-80 standards. See page 23 for additional details.

Kim Lighting is committed to supporting continuous improvement of SSL product quality and assuring the products we deliver perform as promised.

MADEUSA

INThE

More Than Just Energy Savings...An Enhanced Green Footprint

Coast , Wildlife, and Turtle Friendly Clean Industrial Wastewater AwardSpecify WARP9 LED with 1700K amber LEDs to create safe zones and protect sensitive nocturnal animal life.

Kim Lighting’s California factories have been awarded the Sanitation District of LA County’s clean water certification each year since 2006.

The Lighting Facts trademark is registered to the U.S. Department of Energy.

HID LED Savings Guide

KIM LIGHTING 11

Description Total Luminaire Wattage

Energy Savings (Watt)

Energy Savings (Kw)

Savings Per Yr @ 11 Hrs per night

@ $0.10 Per Kwh1

WARP9 LED 175 - - -

150W Metal Halide 185 10 .01 $ 44.02

200W Metal Halide 240 65 .065 $ 66.10

250W Metal Halide 291 116 .116 $ 86.57

150W HPS 188 13 .013 $ 45.22

200W HPS 240 65 .065 $ 66.10

250W HPS 295 120 .12 $ 88.181 Assumes HID lamp replacement every three years, includes labor and lamp.

More Than Just Energy Savings...An Enhanced Green Footprint

RoHS/WEEE Compliant Made from +90% Recycled MaterialsKim Lighting is doing its part to limit hazardous waste. WARP9’s housing and LED components meet strict US and international environmental protection and recyclability requirements.

WARP9 LED’s aluminum housing and reflector components are constructed from more than 90% recycled materials and are entirely lead and mercury free.

No Backlight No Backlight

Light Pollution Reduction Technology

WARP9 LED exceeds Illuminating Engineering Society and International Dark Sky Association full cutoff requirements for applications where light pollution or light trespass may be a concern. WARP9 LED's unique optical system and smooth flat glass lens produces full cutoff with zero light above 90° contributing to the enjoyment of celestial visibility at night for future generations.

WARP9 LED with the IDA Fixture Seal of Approval™ meets full cutoff regulations in any jurisdiction.

The Future of Dark Sky Compliance

KIM LIGHTING 12

The IDA Fixture Seal of Approval is a trademark owned by the International Dark-Sky Association.

Neighbor Friendly Backlight Elimination

Being neighbor friendly was an important requirement when developing WARP9 LED. Because each of its MicroEmitter™ modules are directed forward in its Type 2, 3, and 4 distributions, any backlight is precisely blocked to eliminate spill light and light pollution behind the pole or across property lines, and without any unsightly drop-down shield or efficiency loss.

WARP9’s versatile design also allows this Neighbor Friendly feature to be factory customized to illuminate sidewalks or other house-side zones where limited backlight is desired. Contact your Kim Lighting representative for additional details on creating custom distributions.

Welcome to the Neighborhood, WARP9!

KIM LIGHTING 13

No Backlight No Backlight

WARP9 LEDIES Type III Distribution120 LEDs25' Mounting Height

Avg. Outdoor Ambient Temp.

Estimated LED Life

Expectancy

OperatingLife in Years

at (10) Hours Per Night

-60°C / -76°F 80,000 hrs. 21.92 yrs

-50°C / -58°F 80,000 hrs. 21.92 yrs

-40°C / -40°F 80,000 hrs. 21.92 yrs

-30°C / -22°F 76,000 hrs. 20.82 yrs

-20°C / -4°F 72,000 hrs. 19.73 yrs

-10°C / +14°F 68,000 hrs. 18.63 yrs

0°C / +32°F 64,000 hrs. 17.53 yrs

+10°C / +50°F 60,000 hrs. 16.44 yrs

+20°C / +68°F 56,000 hrs. 15.34 yrs

+30°C / +86°F 52,000 hrs. 14.25 yrs

+40°C / +104°F 50,000 hrs. 13.70 yrs

+50°C / +122°F 50,000 hrs. 13.70 yrs

+60°C / +140°F 50,000 hrs. 13.70 yrs

Advanced Technology Exclusives

WARP9 LED employs two distinct but complimentary methods to maintain the optimal operating temperature for its advanced LED sources: First, WARP9 LED uses dissipation and air flow to draw heat away from the fully sealed reflector chamber. Each MicroEmitter™ incorporates a solid aluminum heat sink, which is then snapped into the EmitterDeck™, a stacked and spaced removable carrier plate designed to maximize cooling surface area. This module is then fixed to WARP9 LED’s thick diecast aluminum housing and external cooling ribs to effectively disperse heat away from the optical chamber. In addition, a solid cast aluminum wall completely separates the LEDs from the breathable adjacent driver compartment, further improving LED and driver life.

Additionally, each WARP9 LED circuit board is equipped with an individual thermal junction monitor that automatically adjusts each LED board according to the ambient temperature. This feature allows the LEDs to realize their maximum life in extreme and fluctuating weather conditions including hot zones without overheating or failing. This, along with its very low EPA rating, means that WARP9 LED can be installed almost anywhere in almost any climate.

A Unique Dual Approach to Reliable Heat Management

KIM LIGHTING 14

Advanced Technology Exclusives

WARP9 LED is offered in two standard color temperatures to meet the needs of a variety of modern applications. Specify 3500K fixtures in residential and suburban zones to improve skin color rendering and to provide a warmer, hospitable atmosphere. Specify 5100K fix-tures for higher mounting heights and basic street lighting for greater reach and improved visual acuity. Other color temperatures are also available, including 1700K amber color for wildlife and turtle zones. Contact your Kim Lighting representative for details.

Two Standard Color Temperatures: 3500K and 5100K

KIM LIGHTING 15

Specify: 3500K 5100K 580nm

Cat. No. L3K L5K L2K

Description Daylight Bright White Amber

Light Color

Angled sidewallsreflect sky

Hollow arm design

Framelessglass lens

Signature Kim cooling fins

Round pole selection

Curved topreflects sky

Stealth Gray™ Finish

WARP9 Cloaking Technology

WARP9 is a new concept in luminaire design – visual stealth. Typical site lighting attempts to embellish, decorate, or adorn, often beyond the original architectural intent. WARP9 was conceived and developed with an entirely different directive. WARP9 was designed to disappear from the site, camouflage itself within its surroundings, and avoid detection from daytime visual perception. WARP9 is the antithesis of massive, showy, recognizable, and ornamental luminaires, allowing architecture to remain visually dominant as it was originally intended. WARP9 is a concept that is long overdue, yet one that is light years ahead of its time.

The First Visual Stealth Luminaire

KIM LIGHTING 16

One-piece silicone gasket

Super TGIC finish

Aluminum

Powder Coat

Titanated Zirconium Conversion Coating

Tool-less access

An Obsession with PerfectionWARP9 Cloaking Technology

WARP9’s housing and arm assembly are die-cast from low copper alloy (<0.6% Cu) aluminum for precision and repeatability. The housing is internally reinforced at the arm connection, and cooling fins are integral with the top and gear cover surfaces. This self-cooling feature substantially reduces the operating temperatures of heat-sensitive electrical components, promoting extended life.

A concealed die-cast latch is designed into the nose of the fixture allowing no-tool entry into the optical chamber1. In addition, the completely separated driver compartment is accessed through a flush, bottom mounted tool-less slide latch for servicing electrical components and wiring access.1

1Tamper-Resistant option available

Kim Lighting's FoundryLos Angeles, California

Exacting Fabrication and Assembly Standards

KIM LIGHTING 17

Modern Installation & Maintenance Features

KIM LIGHTING 18

Easy Installation & Set-Up Simple Maintenance

The attachment of lighting fixtures to poles is often a neglected detail that ruins a clean design with boxy armatures and exposed nuts, bolts, or screws. WARP9’s arm connection naturally integrates and blends with the fixture head for a clean, strong appearance without exposed hardware or attachments. WARP9 also utilizes an internal mounting-bolt system concealed within the arm, fixture, and pole for maximum rigidity and assured coupling.

Inside the pole top, a reinforcing plate receives the mounting bolts. A strain relief is provided on the reinforcing plate for securing the field wires. The cast-aluminum arm has concealed mounting bolts accessible through a flush cover that blends with the arm pre-assembled at Kim Lighting. The arm is configured to complement the fixture design and make the fixture-to-pole connection appear natural, logical, and homogeneous.

Ease of maintenance is a feature that distinguishes a lifetime product from an inferior substitution. WARP9 utilizes modular construction for easy installation and maintenance, and to allow for upgrading as source technology advances.

To replace an LED EmitterDeckTM, a single latch on the nose of the fixture opens the hinged frameless lens. If driver replacement is required, the entire electrical module is accessed through a separate latched door on the underside of the fixture, and includes quick-disconnect plugs on all wiring.

WARP9 LED uses modern plug-n-play mounting and connection features right out of the box that make installation a snap. In addition, WARP9 LED’s fully sealed optical chamber keeps bugs, dirt, and debris away from the LEDs for their entire life, and the tempered flat glass lens and rugged IP66 rating make cleaning simple and thorough.

®

WP9S

WP9S

WP9S

GEMLED

WP9L

WP9L

KIM LIGHTING 19

Modern Installation & Maintenance Features Proportion Guide

Ordering Example:

Mounting3SY configurtion is available for round poles only.

1

EPA WP9S: 0.52 1.04 0.82 1.3 1.3 1.5 n/aEPA WP9L: 0.95 1.9 1.47 2.4 2.4 2.7 n/a Cat. No.: 1SA 2SB 2SL 3ST 3SY 4SC 1W

WallMount

3

FixtureCatalog no. designates fixture and light distribution.

2

Plan View:

HOUSiNGWP9 = WARP9

SOURCEL = LED

DRivERE=Electronic

SiZES = Small, 60 LEDs, 88WL = Large, 120 LEDs, 175W

COLOR TEMPERATURE3K = 3500K5K = 5100K2K = 1700K Amber

DiSTRiBUTiON2 = Type II Full Cutoff3 = Type III Full Cutoff4 = Type IV Full Cutoff 5 = Type V Square Full CutoffR = Type R Right Full CutoffL = Type L Left Full Cutoff

Type IVForwardThrow

Type LLeft

Type II

Type VSquare

Type III

Type RRight

Light Distribution

1SA / WP9LE3 / L5K240 / SG / A-35 / PRA20-4188SA/SG / VSF-1SA

WP9

L

E

1 2 3 4 5-12 13 14

Electrical Module

WARP9 LED

KIM LIGHTING 20

Wall Mounting:5 Cat. No.: 1W

FinishSuper TGIC powder coat paint over titanated zirconiumconversion coating.

Color: Stealth Gray Light Gray Platinum Silver White Black Dark Bronze Custom Colors Cat. No.: SG LG PS WH BL DB CC

4

A cast-aluminum mounting plate is mounted to the wall with four bolts (by others). Fixture and arm are mounted to the cast aluminum cover plate before attaching to the wall mounting plate. The fixture-arm-cover plate asssembly is hooked to the wall mounting plate and secured with stainless steel screws provided. Field splices are made at the opening in the cover plate. Cover is finished to match arm and fixture color.

High temperature fuse holders factory installed inside the fixture housing. Fuse is included.Line Volts: 120V 208V 240V 277V 347V 480VCat. No.: SF DF DF SF SF DF

Optional Fusing:6

Consult your Kim Lightingrepresentative for custom colors.

1 Due to current unavailability of 347V and 480V drivers, specification of these voltages shall feature an integral step-down transformer. Driver compartment door extends down 1" on small housing and 1M" on large housing to accommodate. See page 22.

vOLTAGE120 = 120V208 = 208V240 = 240V277 = 277V347 = 347V1

480 = 480V1

Standard die-cast latches are optical cavity and electrical cavity provided with a captive 10-32 stainless steel flat socket-head screw to prevent unauthorized opening. Required only for vandal protection in locations where fixtures may be reached by unauthorized persons.

Optional Tamper-Resistant Latches:

9

Replaces standard mounting arm with a slipfitter for mounting to a horizontal pole davit-arm with 2" pipe-size mounting end (2 C " O.D.). Provides ±5° vertical fixture adjustment.

Optional Horizontal Slipfitter Mount:

10

Optional Photocell:7 Cat. No.: A-25 Receptacle

A-30 - A-35 Button

Two types of photocell controls are available. A receptacle for a NEMA base photocell (by others) is located above the electrical compartment. Also available is an internal photocell with a button sensor on the left side of the fixture. For all multiple-fixture pole mountings with two or three fixtures, one fixture has a receptacle to operate the others.

Button

Receptacle

Optional Lexan® FlatNon-Yellowing Lens:

8 One-piece non-yellowing flat advanced polymer (Lexan® from GE Advanced Materials) replaces standard tempered glass lens.

CAUTiON: Use only when risk of vandalism is anticipated to be high. For LED use only.

Tamper-Resistant Latch

Cat. No.: TL

Cat. No.: HSF

Slipfitter

11

Cat. No.: LS

Lexan® Lens

WARP9 LED Ordering Information

KIM LIGHTING 21

See Kim Arms and Poles Selection Guide for a complete selection of round and square poles in aluminum and steel.

Kim Lighting is working with several driver suppliers and control system manufacturers to develop a variety of proven turnkey solutions to meet any application's need. Kim Lighting will advise availability of complete control packages, and even two-way monitoring systems, once they have been tested and exceed Kim's high quality standards.

Poles:

Dimming Controls:Contact factory for further details and current capabilities.

12

14 Optional Vertical Slipfitter Mounts:

13

Cat. No.: vSF-1SAvSF-2SBvSF-2SLvSF-3ST vSF-3SYvSF-4SC

Cat. No.: SvSF-1SASvSF-2SBSvSF-2SL SvSF-3ST --------------SvSF-4SC

Mounting Configuration1SA - Single arm mount2SB - 2 at 180°2SL - 2 at 90°3ST - 3 at 90°3SY - 3 at 120°45 - 4 at 90°

Allows standard fixture and arm to be mounted to poles having a 2 pipe-size tenon (2C " O.D. x 4K " min. length).

Round Square

Terminal Block located inside the fixture electrical compartment. (For Large WARP9 LED only.)

Special Option forStreet Lighting:

Cat. No.: TB

Lexan is a registered trademark owned by GE Advanced Materials

TOP

SIDEFRONT

BOTTOM

8I"(227 mm)

15"(381 mm)

1K"(38 mm)

4B"(105 mm)

26I"(684 mm)

8I"(227 mm)

5N"(141 mm)

4G"(113 mm)

1"(25 mm)

347/480V Driver1

TOP

SIDEFRONT

BOTTOM

35B"(892 mm)

10M"(262 mm)

5I"(151 mm)

5B"(130 mm)

10M"(262 mm)

20"(508 mm)

1I"(49 mm)

5K"(140 mm)

1M"(33 mm)

347/480V Driver1

KIM LIGHTING 22

SpecificationsHOUSING: One-piece die-cast, low copper alloy (<0.6% Cu) aluminum with integral cooling ribs over the electrical compartment. Solid barrier wall separates optical and electrical compartments. A single die-cast aluminum cam-latch provides positive locking and sealing of the optical chamber. A one-piece extruded and vulcanized silicone gasket seals the housing against the lens surface.

ELECTRONIC DRIVER MODULE: One-piece die-cast, low copper alloy (<0.6% Cu) aluminum with integral cooling ribs over exposed bottom surface. Integral hinges and slide latch with stainless steel hardware provides no-tool mounting and removal from housing. All electronic components are UL and CSA recognized and mounted directly to the driver tray for maximum heat dissipation.

LENS: Clear F" thick tempered glass lens retained by a stainless steel piano hinge and a single die-cast aluminum cam-latch. The edges are camouflaged to conceal the outer portion of the housing.

OPTICAL MODULE: Precision injection molded, high specular reflectors are positioned to achieve directional control toward desired task. Secondary high specular reflector 95% Miro4 panels surround the module to redirect light downward. No fasteners are placed on the reflective surface. The entire assembly fastens to the housing as a one-piece module and features wiring quick-connects for easy upgrading.

SUPPORT ARM: Heavy cast, low copper alloy aluminum with stainless steel mounting bolts. A pole reinforcing plate is provided with wire strain relief. Arm is circular cut for specified round pole.

FINISH: Super TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness, applied over a titanated zirconium conversion coating; 2500 hour salt spray test endurance rating. Standard colors are Black, Dark Bronze, Stealth Gray™, Platinum Silver, or White. Custom colors are available.

CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury.

Listings and Ratings UL cUL 1598 CE IP66 25°C Ambient

Kim Lighting reserves the right to change specifications without notice.

WP9SESmall LED60 LEDsEPA: .52Maximum Weight:17 lbs.Maximum System Watts = 88 W

WP9LELarge LED120 LEDsEPA: .95Maximum Weight:35 lbs.Maximum System Watts = 175 W

Small Specs Large Specs

1 Driver compartment door extends down 1" on small housing and 1M" on large housing to accommodate integral step-down transformer on 347V and 480V models (only).

KIM LIGHTING 23

LEDs and Absolute PhotometryThe LM-79-2008 absolute photometric principles for LEDs are new to the industry and are quite different than the relative photometric principals that have been used for years with HID luminaires.

TRADITIONAL RELATIVE PHOTOMETRYWith traditional relative photometric testing, the lamp is tested separately prior to testing the luminaire as a system to determine actual lumen output of the lamp. After the lamp is tested, the lamp manufacturers’ published initial lumen output is divided by the actual lumen output to determine a lamp factor. The luminaire is then tested and the lamp factor can be applied to all candela measurements.

LM-79 ABSOLUTE PHOTOMETRYAlternatively, the absolute photometric testing process does not test the source independently from the system. There is no lamp factor to adjust the output of the source to the lamp manufacturers’ published diode output. The LEDs are completely dependent on their function within the overall luminaire system to be accurately measured, and the lumen output data from the LED manufacturer should not be used because it is based on raw bare diode data collected prior to being assembled onto PC boards in the luminaire.

Small Specs Large Specs WARP9 LED and LM-79-2008 Photometry

(INDICATES STANDARD IES FORMATTING)

Actual Test Report

WHY DO LED LUMINAIRES USE THE ABSOLUTE PHOTOMETRIC TESTING METHOD?

1. LEDs in luminaires act like clusters rather than individual sources.

2. The output of individual LEDs is less consistent than HID sources.

3. The performance of an LED is dependent on its integration within the luminaire to account for thermal, optic and driver variables. Conversely, HID lamps are a single source and relative photometry accounts for these losses in the output data.

Kim Lighting’s photometry data for WARP9 LED luminaires are tested to the IESNA LM-79-2008 standard, and Kim Lighting will only use LEDs that are tested to the IESNA LM-80-2008 standard. Indication that photometric data has been tested using the approved LM-79-2008 method is the use of a negative one (-1) in the lumen output space of the photometric data file. Be aware that other manufacturers may elect to assign a lumen value to the photometric test report after the fact, however any IES report for an LED luminaire with a non-negative lumen value should be considered invalid, and does not follow industry standards established by LM-79-2008.

The following test reports (pages 24-28) reflect photometry performed under LM-79-2008 standards.

Type II - 60 LED

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

34

1

.5

.2

.1

.05

180°

UH

UL

FVH 90° = 3.9%

FL 30° = 4.0%

FM 60° = 23.5%

FH 80° = 41.0%

0°

100°100°FORWARD LIGHT2004 lm. 72.4%

UP LIGHT0 lm. 0%

BACK LIGHT764 lm. 27.6%

BVH 90° = 1.4%

BH 80° = 14.1%

BM 60° = 9.6%

BL 30° = 2.4%

Small WARP9 LED Photometry

KIM LIGHTING 24

Type III - 60 LED

180°

UH

UL

FVH 90° = 3.3%

FL 30° = 3.6%

FM 60° = 26.7%

FH 80° = 42.4%

0°


UP LIGHT0 lm. 0%


BVH 90° = 0.9%

BH 80° = 9.4%

BM 60° = 10.0%

BL 30° = 3.7%

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

3

4

1

.5

.2

.1

LM-79-2008 Test Results


Report Number KLV01650

Mounting Height 12 Feet

Light Dist. Type Type II

Total Flux 2769 Lm.

System Watts 88W



Light Dist. Type Type III

Total Flux 3075 Lm.

System Watts 88W

.05

.IES files available at www.kimlighting.com.As LED technology advances, photometric data is subject to change. Always consult factory for current luminaire lm/w (lumen per watt) and other technical data.

Type IV - 60 LED

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

34

180°

UH

UL

FVH 90° = 2.7%

FL 30° = 6.2%

FM 60° = 36.6%

FH 80° = 47.3%

0°


UP LIGHT0 lm. 0%


BVH 90° = 0.1%

BH 80° = 1.6%

BM 60° = 3.7%

BL 30° = 1.8%

2

.5

.2

.05

.1

1

Small WARP9 LED Photometry

KIM LIGHTING 25

Type V - 60 LED

hOuSE STREET

0

1

23

1

2

3

4

3

2

1

0

1

2

3

180°

UH

UL

FVH 90° = 2.5%

FL 30° = 1.7%

FM 60° = 18.3%

FH 80° = 28.3%

0°


UP LIGHT0 lm. 0%


BVH 90° = 3.0%

BH 80° = 28.4%

BM 60° = 16.2%

BL 30° = 1.6%

1.5

.2.1

4





Light Dist. Type Type IV

Total Flux 3289 Lm.

System Watts 88W



Light Dist. Type Type V

Total Flux 2813 Lm.

System Watts 88W

.05


Type II - 120 LED

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

34

1.5

.2

.1

Large WARP9 LED Photometry

Report Number KLV01647A

Mounting Height 20 Foot


Total Flux 5501 Lm.

Sytem Watts 175W

KIM LIGHTING 26

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

34

.5

.2

.1

1

Type III - 120 LED

180°

UH

UL

FVH 90° = 3.2%

FL 30° = 3.9%

FM 60° = 26.6%

FH 80° = 43.9%

0°


UP LIGHT0 lm. 0%


BVH 90° = 1.1%

BH 80° = 9.9%

BM 60° = 8.4%

BL 30° = 3.0%

180°

UH

UL

FVH 90° = 3.6%

FL 30° = 2.7%

FM 60° = 23.3%

FH 80° = 40.8%

0°


UP LIGHT0 lm. 0%


BVH 90° = 1.7%

BH 80° = 16.0%

BM 60° = 9.8%

BL 30° = 2.2%



Report Number KLV01646B


Light Dist. Type Type II

Total Flux 5377 Lm.

System Watts 175W

Report Number KLV01607J


Light Dist. Type Type III

Total Flux 5471 Lm.

System Watts 175W

.05

.05


Type IV - 120 LED

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

34

2

.5

.2

.1

1

180°

UH

UL

FVH 90° = 2.2%

FL 30° = 5.5%

FM 60° = 36.9%

FH 80° = 46.7%

0°


UP LIGHT0 lm. 0%


BVH 90° = 0.2%

BH 80° = 2.6%

BM 60° = 4.0%

BL 30° = 1.8%

Large WARP9 LED Photometry


Report Number KLV01645D


Light Dist. Type Type IV

Total Flux 5942 Lm.

System Watts 175W

KIM LIGHTING 27

Type V - 120 LED

hOuSE STREET

0

1

23

1

2

3

4

3

2

1

0

1

2

3

4




Total Flux 5501 Lm.

System Watts 175W


.5

.2

.1

.05

.05

180°

UH

UL

FVH 90° = 2.3%

FL 30° = 1.6%

FM 60° = 17.1%

FH 80° = 28.8%

0°


UP LIGHT0 lm. 0%


BVH 90° = 3.0%

BH 80° = 30.1%

BM 60° = 15.6%

BL 30° = 1.5%


Type R - 60 LED

hOuSE STREET

0

-1

-2-3

1

2

3

4

3

2

1

0

1

2

34

1

2

5

.5

.2

.1

Right Orientation

180°

UH

UL

FVH 90° = 3.6%

FL 30° = 2.7%

FM 60° = 23.3%

FH 80° = 40.8%

0°


UP LIGHT0 lm. 0%


BVH 90° = 1.7%

BH 80° = 16.0%

BM 60° = 9.8%

BL 30° = 2.2%

Exclusive One-Way Photometry

KIM LIGHTING 28

Type L - 120 LED

3

2

1

0hOuSE STREET

0

-1

-2

-3

1

2

3

1

2

3

4

.5.2

.1.05

12

4

Left Orientation

180°

UH

UL

FVH 90° = 3.2%

FL 30° = 3.9%

FM 60° = 26.6%

FH 80° = 43.9%

0°


UP LIGHT0 lm. 0%


BVH 90° = 1.1%

BH 80° = 9.9%

BM 60° = 8.4%

BL 30° = 3.0%





Light Dist. Type Type R

Total Flux 3187 Lm.

System Watts 88W

Report Number KL016600


Light Dist. Type Type L

Total Flux 6248 Lm

System Watts 175W


Warranty InformationExclusive One-Way Photometry

KIM LIGHTING 29

PGL7 LED Parking Structure

NEW

LED Landscape Collection LED Architectural Lighting LED Compact Floodlight

Additional Kim Lighting Premium LED Luminaires

Standard WARP9 LED Limited Manufacturer’s WarrantyKim Lighting LED lighting products are long lasting and energy efficient. Your purchase of environmentally friendly Kim Lighting LED luminaires is helping contribute to a healthier environment and supports your commitment as an energy efficient consumer.

Contact Kim Lighting for complete warranty language, exceptions, and limitations, and availability of PlusOne extended warranty options.

When properly installed and under normal conditions of use, Kim Lighting warrants WARP9 LED luminaire products ("Product(s)") sold by it to be free from defects in material and workmanship for (i) a period of five (5) years for metal parts, (ii) a period of ten (10) years for paint finishes, and, (iii) a period of six (6) years or 20,000 operating hours (whichever comes first) for LED Light Engines and LED power components, from the date of sale of such goods to the buyer as specified in Kim Lighting shipment documents for each Product(s). The buyer agrees to make all claims regarding defects or deficiencies in the Product(s) according to the terms of Kim Lighting's official warranty. Warranty claims must be made in writing according to Kim Lighting procedures existing at the time of the claim. Valid warranty claims must be made within the warranty period specified herein above, and submitted within thirty (30) days of discovery of the damage or defect. NO FIELD LABOR, REPAIR, DISMANTLE, OR INSTALLATION CHARGES ARE INCLUDED WITH THIS WARRANTY. Kim Lighting may repair or replace any Product(s) covered by this warranty at its sole discretion and in accordance with its procedure. Any unauthorized return, repair, replacement or modification of the Product(s) shall void this warranty. This warranty applies only to the use of the Product(s) as intended by Kim Lighting and does not cover any misapplication or misuse of said Product(s), or installation in hazardous or corrosive environments. Contact Kim Lighting for complete warranty language, exceptions, and limitations.

W A R P 9 L E D W A R R A N T Y

5/6/10

MAILING ADDRESSP.O. BOX 60080CITY OF INDUSTRY, CA 91716-0080

Printed in U.S.A.93022105 Version 1.3 (10/09)

www.kimlighting.comPATENT PENDINGBECAUSE OF CONTINUING PRODUCT IMPROVEMENT PROGRAMS, KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE.ENTIRE CONTENTS © COPYRIGHT 2009 KIM LIGHTING INC. ALL RIGHTS RESERVED REPRODUCTION IN WHOLE OR IN PART WITHOUT PERMISSION IS STRICTLY PROHIBITED.

BUSINESS ADDRESS16555 EAST GALE AVENUECITY OF INDUSTRY, CA 91745PHONE: 626.968.5666FAX: 626.369.2695

WARP9®

LED

WARP9 LED - CNR Lighting

Documents

Transcript of WARP9 LED - CNR Lighting