WARNING: The ladder must not be used • DO NOT until it ......WARNING: The ladder must not be used...
1
WARNING: The ladder must not be used until it has been fully installed in the loft. • WARNING: Ensure the ladder is fully extended, both lock catches are fully engaged and the top stops are against the guide/pivot assemblies before each use. • WARNING: Only to be used by one person at a time. • IMPORTANT: In some cases it may be necessary to install additional wooden braces or noggins to be able to fix the pivot arm in the correct position. • IMPORTANT: During installation ensure the work area is kept clean and free from obstructions. • IMPORTANT: Non-authorised parts may be dangerous and will invalidate the warranty. • IMPORTANT: Read and follow all of the safety information on the side of the ladder. • IMPORTANT: When not in use, stow the ladder securely. • IMPORTANT: All ladders have potential injury risks, please follow these instructions at all times. • IMPORTANT: A separate suitable ladder is needed to access the loft during installation. • IMPORTANT: Two persons are needed to safely complete the installation, one person working from inside the loft, the other on the ground below. • DO NOT use the ladder for any purpose other than that for which it was designed. • DO NOT install or use until you have read the instructions completely. Ensure you understand the limitations and potential hazards. • DO NOT fit loft ladder brackets, pivots or other fixings to chipboard or composite board. • DO NOT install if parts are missing or damaged. • DO NOT use if parts are missing or damaged. • DO NOT allow children to climb the ladder. • DO: Wear non-slip footwear and if necessary clean the soles before using the ladder. • DO: Ensure the ladder rungs are horizontal and both ladder feet are on the floor. • DO: Always grip the ladder when climbing. Always try to keep three points of contact with the ladder. • DO: Always face the ladder when ascending and descending. • DO: Only carry light materials (up to 10kg) up the ladder. Never exceed the total static load of 100kg. • DO: Keep these instructions in a safe place for future reference. • DO: Ensure there is a good flat access area at the base of the ladder to dismount safely. A minimum area of 1 square metre is recommended. • DO: Ensure there is enough clear internal loft space for the ladder to be stowed before attempting installation (see specifications). • DO: Keep children, animals and unauthorised persons away from the working area. • DO: Ensure there is sufficient lighting in the work areas. • DO: Keep the ladder in good condition. Please check that you have all the components against the list below and that they are in good condition before installation. If any components are missing contact the retailer. Tools and Equipment needed: Suitable ladder to access loft, Ruler & tape measure (3 metre), Sharp knife, Pencil, Bradawl (sharp point), Drill, 2mm & 13mm wood drill bits, Phillips screwdriver (medium), Flatblade screwdriver (medium), 8mm & 19mm Spanners, Lighting for loft. Assembly and Installation 1. Attach hinges to trapdoor and opening. Drill 2mm pilot holes, attach hinges (K) to trapdoor and surround using 8 x csk 20mm screws (N). Note: The trapdoor will attach to the same side of the opening as the ladder (Trapdoor is not supplied). 2. Mark and drill catch hole in trapdoor. Mark the centre line onto the opening edge of the trapdoor. Measure 25mm in from the opening edge of the trapdoor and drill a 13mm hole (a). Note: If the trapdoor opening has a rebate ‘X’, add this distance to the 25mm (X + 25mm) (b). 3. Assemble the catch. Assemble the catch onto the trapdoor ensuring the ‘tab’ on the catch barrel and the catch are positioned as shown (a). Note: Only fix the retaining washer (D3) using the 12mm screw (M) once correctly positioned as shown above (b). 4. Attach catch plate. Find and mark the centre line onto the opening end of the trapdoor surround. Allow a 7mm gap between the top of the catch plate and the trapdoor (b or c). Attach the catch plate (D4) to the trapdoor surround using 2 x 12mm screws (a). 5. Fit the ends to the pole (a). To lock: Turn anti- clockwise, To unlock: Turn clockwise (b). 6. Prepare the loft ladder. Using a sharp knife, carefully cut along the grooves and remove both end caps. Keep end caps for later use. 7. Loosely insert 12mm screws (M) into both stops (H) and slide into the top ladder section. 8. Slide the glide/pivot assembly (F) into the ladder, ensure it is fitted the correct way around as shown. 9. Loosely insert 12mm screws (M) into both retainers (I) and slide into the ladder. Refit both end caps. 10. Measure the distance between the floor of the room to the floor of the loft (2.70m used as example) (a). Place paper template (G) on back ladder section with the cut- out lining up with the top hole. Position the stop at the required height (2.70m used as example), tighten both stop screws (b). Repeat with stop on other side of ladder. 11. Attach the handrail. Note: The handrail (C) can be attached to either side of the ladder as required. 12. Using a suitable ladder gain access to the loft and position the ladder centrally across the loft opening with the pivot assembly resting squarely on the trapdoor surround. To help with access, release the lock catch on the end of the top ladder section and slide the middle and bottom sections down the ladder. 13. Ensure both pivots (F) are spaced as far apart as possible (up against the glides). Use a bradawl or small drill to start the screw holes, attach the pivots to the trapdoor surround using 10 x 25mm screws (P). Note: The trapdoor surround must be solid wood. Chipboard or composite board will not be strong enough. 14. Fully extend ladder out of loft opening. Release the lock catch on middle ladder section and extend bottom section until it locks (a). Repeat with the catch on the top section and extend the middle section until it locks (b). Important: Ensure top stops (H) are tight against glides (c) and feet sit evenly on the floor below. 15. Fit the pivot arm (E). Fit covers (U). 16. Attach the pivot arm to the loft floor/wooden batten (this may have to be added at the correct distance) using the pivot arm bracket. Use a bradawl or small drill to start the screw holes, attach the bracket (L) to the loft floor using 4 x 20mm screws (O). 17. Release the lock catch on the top ladder section (1) and slide the middle section up until it locks. Release the lock on the middle section (2) and slide the bottom section up until it locks. Use the pole to fully stow the ladder. With the ladder fully stowed, slide the retainers 18. To lower ladder. Insert the pole (B) into the round hole on the bottom ladder section and carefully pull down until bottom section rests on top stops. IMPORTANT: DO NOT allow ladder to fall under its own weight. 19. When ladder comes to a stop, release catch on middle section (1) and lower bottom section (2) until it locks into place (a). Release catch on top section (3) and lower middle section (4) until it locks into place (b). Important: Ensure top stops (H) are tight against glides (c) and feet sit evenly on the floor. To stow ladder repeat steps 18 and 19 in reverse order. Opening edge a b a b a b up to the glide/pivot assembly (F) and clip onto the glide. Ensure both retainers (I) are the same distance from the end of the ladder and tighten the 4 retainer screws. Important: Ensure ladder clears trapdoor when closed. Operating Instructions Safety Information - Before installing or using the loft ladder carefully read and follow the safety information below. A x 1 B x 1 C x 1 M 12mm x 12 N 20mm csk x 8 O 20mm x 4 P 25mm x 10 R 8mm x 2 Q 65mm x 2 D1 x 1 G x 1 E x 1 F x 1 H x 2 I x 2 J x 2 K x 2 L x 1 T x 1 U x 2 V x 1 S x 2 Trapdoor Trapdoor opening 25mm X = Opening rebate X Draught excluder (if fitted) Inside loft Thickness of trapdoor Trapdoor Trapdoor opening 25mm a b 25mm 13mm catch hole Opening edge Centre line Trapdoor 25mm 13mm catch hole Opening edge Centre line Trapdoor X 25mm ‘Tab’ in locked position a b Catch in locked position 7mm Trapdoor Trapdoor opening Centre line Catch plate Catch plate 7mm Trapdoor Trapdoor opening Catch plate Draught excluder (if fitted) a b c Unlocking ‘Tab’ in locked position End caps End caps Measure from floor to floor (2.70m used as example) c 1 2 1 3 a b c N N K T D5 D2 M D3 M D4 M H H F H B V D1 B M I I I J Q C Q J R S R S L O E U P P F F I H H D2 x 1 D3 x 1 D5 x 1 D4 x 1 = = G B 2 4 C Youngmans 3 Section Loft Ladder.indd 1 8/3/12 18:07:47
Transcript of WARNING: The ladder must not be used • DO NOT until it ......WARNING: The ladder must not be used...
WARNING: The ladder must not be used until it has been fully installed in the loft.
• WARNING: Ensure the ladder is fully extended, both lock catches are fully engaged and the top stops are against the guide/pivot assemblies before each use.
• WARNING: Only to be used by one person at a time.
• IMPORTANT: In some cases it may be necessary to install additional wooden braces or noggins to be able to fix the pivot arm in the correct position.
• IMPORTANT: During installation ensure the work area is kept clean and free from obstructions.
• IMPORTANT: Non-authorised parts may be dangerous and will invalidate the warranty.
• IMPORTANT: Read and follow all of the safety information on the side of the ladder.
• IMPORTANT: When not in use, stow the ladder securely.
• IMPORTANT: All ladders have potential injury risks, please follow these instructions at all times.
• IMPORTANT: A separate suitable ladder is needed to access the loft during installation.
• IMPORTANT: Two persons are needed to safely complete the installation, one person working from inside the loft, the other on the ground below.
• DO NOT use the ladder for any purpose other than that for which it was designed.
• DO NOT install or use until you have read the instructions completely. Ensure you understand the limitations and potential hazards.
• DO NOT fit loft ladder brackets, pivots or other fixings to chipboard or composite board.
• DO NOT install if parts are missing or damaged.
• DO NOT use if parts are missing or damaged.
• DO NOT allow children to climb the ladder.
• DO: Wear non-slip footwear and if necessary clean the soles before using the ladder.
• DO: Ensure the ladder rungs are horizontal and both ladder feet are on the floor.
• DO: Always grip the ladder when climbing. Always try to keep three points of contact with the ladder.
• DO: Always face the ladder when ascending and descending.
• DO: Only carry light materials (up to 10kg) up the ladder. Never exceed the total static load of 100kg.
• DO: Keep these instructions in a safe place for future reference.
• DO: Ensure there is a good flat access area at the base of the ladder to dismount safely. A minimum area of 1 square metre is recommended.
• DO: Ensure there is enough clear internal loft space for the ladder to be stowed before attempting installation (see specifications).
• DO: Keep children, animals and unauthorised persons away from the working area.
• DO: Ensure there is sufficient lighting in the work areas.
• DO: Keep the ladder in good condition.
Please check that you have all the components against the list below and that they are in good condition before installation. If any components are missing contact the retailer.
Tools and Equipment needed: Suitable ladder to access loft, Ruler & tape measure (3 metre), Sharp knife, Pencil, Bradawl (sharp point), Drill, 2mm & 13mm wood drill bits, Phillips screwdriver (medium), Flatblade screwdriver (medium), 8mm & 19mm Spanners, Lighting for loft.
Assembly and Installation
1. Attach hinges to trapdoor and opening. Drill 2mm pilot holes, attach hinges (K) to trapdoor and surround using 8 x csk 20mm screws (N). Note: The trapdoor will attach to the same side of the opening as the ladder (Trapdoor is not supplied).
2. Mark and drill catch hole in trapdoor. Mark the centre line onto the opening edge of the trapdoor. Measure 25mm in from the opening edge of the trapdoor and drill a 13mm hole (a). Note: If the trapdoor opening has a rebate ‘X’, add this distance to the 25mm (X + 25mm) (b).
3. Assemble the catch. Assemble the catch onto the trapdoor ensuring the ‘tab’ on the catch barrel and the catch are positioned as shown (a). Note: Only fix the retaining washer (D3) using the 12mm screw (M) once correctly positioned as shown above (b).
4. Attach catch plate. Find and mark the centre line onto the opening end of the trapdoor surround. Allow a 7mm gap between the top of the catch plate and the trapdoor (b or c). Attach the catch plate (D4) to the trapdoor surround using 2 x 12mm screws (a).
5. Fit the ends to the pole (a). To lock: Turn anti-clockwise, To unlock: Turn clockwise (b).
6. Prepare the loft ladder. Using a sharp knife, carefully cut along the grooves and remove both end caps. Keep end caps for later use.
7. Loosely insert 12mm screws (M) into both stops (H) and slide into the top ladder section.
8. Slide the glide/pivot assembly (F) into the ladder, ensure it is fitted the correct way around as shown.
9. Loosely insert 12mm screws (M) into both retainers (I) and slide into the ladder. Refit both end caps.
10. Measure the distance between the floor of the room to the floor of the loft (2.70m used as example) (a). Place paper template (G) on back ladder section with the cut-out lining up with the top hole. Position the stop at the required height (2.70m used as example), tighten both stop screws (b). Repeat with stop on other side of ladder.
11. Attach the handrail. Note: The handrail (C) can be attached to either side of the ladder as required.
12. Using a suitable ladder gain access to the loft and position the ladder centrally across the loft opening with the pivot assembly resting squarely on the trapdoor surround. To help with access, release the lock catch on the end of the top ladder section and slide the middle and bottom sections down the ladder.
13. Ensure both pivots (F) are spaced as far apart as possible (up against the glides). Use a bradawl or small drill to start the screw holes, attach the pivots to the trapdoor surround using 10 x 25mm screws (P). Note: The trapdoor surround must be solid wood. Chipboard or composite board will not be strong enough.
14. Fully extend ladder out of loft opening. Release the lock catch on middle ladder section and extend bottom section until it locks (a). Repeat with the catch on the top section and extend the middle section until it locks (b). Important: Ensure top stops (H) are tight against glides (c) and feet sit evenly on the floor below.
15. Fit the pivot arm (E). Fit covers (U). 16. Attach the pivot arm to the loft floor/wooden batten (this may have to be added at the correct distance) using the pivot arm bracket. Use a bradawl or small drill to start the screw holes, attach the bracket (L) to the loft floor using 4 x 20mm screws (O).
17. Release the lock catch on the top ladder section (1) and slide the middle section up until it locks. Release the lock on the middle section (2) and slide the bottom section up until it locks. Use the pole to fully stow the ladder. With the ladder fully stowed, slide the retainers
18. To lower ladder. Insert the pole (B) into the round hole on the bottom ladder section and carefully pull down until bottom section rests on top stops.
IMPORTANT: DO NOT allow ladder to fall under its own weight.
19. When ladder comes to a stop, release catch on middle section (1) and lower bottom section (2) until it locks into place (a). Release catch on top section (3) and lower middle section (4) until it locks into place (b). Important: Ensure top stops (H) are tight against glides (c) and feet sit evenly on the floor. To stow ladder repeat steps 18 and 19 in reverse order.
Op
enin
g ed
ge
a b
2.86m 3.00m
2.85m
9 4½ 9 10
(9 4 )
2.80m(9 2 )
2.75m(9 0 )
2.65m(8 8 )
2.70m(8 10 )
a b
a b
up to the glide/pivot assembly (F) and clip onto the glide. Ensure both retainers (I) are the same distance from the end of the ladder and tighten the 4 retainer screws.
Important: Ensure ladder clears trapdoor when closed.
Operating Instructions
Safety Information - Before installing or using the loft ladder carefully read and follow the safety information below.
A x 1 B x 1 C x 1 M 12mm x 12
N 20mm csk x 8
O 20mm x 4
P 25mm x 10
R 8mm x 2
Q 65mm x 2
D1 x 1
G x 1
E x 1 F x 1
H x 2 I x 2 J x 2 K x 2 L x 1
T x 1
U x 2
V x 1
S x 2
Open Stop
Closed Stop
25mm 25mmxx = measure the rebate +25mm
Trapdoor
Trapdoor opening
25mm
Open Stop
Closed Stop
25mm 25mmxx = measure the rebate +25mm
X = Opening rebate
X
Draught excluder (if fitted)
Inside loft
Thickness of trapdoor
Trapdoor
Trapdoor opening
25mm
a b
25mm
13mm catch hole
Opening edge
Centre lineTrapdoor
25mm
13mm catch hole
Opening edge
Centre lineTrapdoor
X
25mm
‘Tab’ in locked position
a
bCatch in locked position
7mm
Trapdoor
Trapdoor opening
Cen
tre
line
Catch plate
Catch plate
7mm
Trapdoor
Trapdoor opening
Catch plate
Draught excluder (if fitted)
a
b c
Unlocking
‘Tab’ in locked
position
End caps
End caps
Measure from floor to floor
(2.70m used as example)
c
1
2
1
3
a b
c
N
N
K
T
D5
D2
M
D3M
D4
M
H
H
F
H
B
V
D1
B
M
II
I
JQCQ
J
R S
R S
L
O
E
U
P
PF
FI
H
H
D2 x 1D3 x 1
D5 x 1
D4 x 1
=
=
G
B
2
4
C
Youngmans 3 Section Loft Ladder.indd 1 8/3/12 18:07:47
