WARNING LIGHTS, ARROWBARS, Brochure …...3 T: +44 (0)113 202 9115 infohaztec.uk T: +44 (0)113 202...

WARNING LIGHTS, ARROWBARS, MESSAGE SIGNS & ANCILLARIES

Motorcycle Systems

INTEGRATED LED SYSTEMS

Brochure

ILS

Brochure

4WARNING BEACONS

SIRENS, SPEAKERS & PROGRAMMABLE CONTROLS

LIGHTBARS& LIGHTBAR LAYOUTS

Brochures

2a&2b

Brochure

3

R65 APPROVED PRODUCTS

Brochure

R65MOTORCYCLE SYSTEMS

Brochure

1

NEW

NOVEMBER 2019

2T: +44 (0)113 202 9115 ∙ [email protected] ∙ www.haztec.ukT: +44 (0)113 202 9115 ∙ [email protected] ∙ www.haztec.uk

R10

R65 Class 2

NEW

Warning lights:- Slimline surface mount warning lights- Compact warning lights- Directional warning lights- Wide angle directional warning lights- Small surface mount warning lights- Large surface mount warning lights- Slim warning lights- Slim vertical warning lights- Number plate mounted warning lights- Screen/deck mounted warning lightsDirectional hideaway lightsInterior vehicle lightsMulti-module warning and Arrowbars

4-10026 slimline dual colour12LED warning light

• Compact but powerful dual colour R65 LED warning light• Dual colour units reduce the need for separate lights• Separate switching • Night dim mode• Multiple units can be synchronised

• Compact design helps make the vehicle less conspicuous when the lights are powered off

• Built-in flasher provides numerous single and dual colour patterns

Mounting: • Surface mount or mount using optional L bracket or roof housing• Also available in a screen mounted housing - see page 15

Voltage: • 10-40VDC - suitable for 12 or 24V use

R65 approvals: • Class 2 - amber/blue

4-10026 12LED ultra slim warning lightDimensions (mm): 124L x 31H x 13DOrder codesDual colour R65 amber/blue 4-10026-EAEBDual colour red/R65 blue 4-10026-EBRDual colour white/R65 blue 4-10026-EBWOther colour combinations available - please contact sales Optional L mounting bracket for 4-10026 4-10033Roof mounted housing for 4-10026 4-10036

All LEDs operate in the selected colour (LEDs change colour)

Dual colour

5 YEAR WARRANTY

Contents

2-182-34-56-7

89

10111213

14-1616-17

1819-21

2223-26

2323

24-2526

27-2829-31

3233343435

InfoSign LED message signsWorklights:

- Dual mount worklights- Linear bar lights- General purpose worklights- High power worklightsMotorised searchlightsScene lightsCigar plug leads and weatherproof switchesRocker switchesHeavy duty switching unitsMotorcycle handlebar switchesLED flash control units

Optional 4-10033 L bracket

4-10036 roof mounted housing

3W LEDs


R10

R65 Class 2

R65 Class 1

R65 Class 2

SINGLE OR SPLIT COLOURS

• Ultra thin - just 10mm deep• Single or split colours with separate switching option

on split colour versions• Built-in flasher with up to 27 patterns• Cruise mode - constant low level illumination• Night dim mode• Multiple units can be synchronised

4-10014/10016 ultra thin 4, 6 & 2x6LED warning lights

• Slimline design - no need to cut holes in vehicle bodywork• Split colour versions feature 2 + 2 LEDs (4-10014) or 3 + 3LEDs

(4-10016) - each colour can be independently controlled• 4-10016-D consists of two independently controlled 4-10016

units sharing a common mount plate for ease of installation - ideal where even higher light output is required

Mounting: • Wide choice of mounting options including surface, L bracket

or roof housing. See page 15 for screen/deck mounted versions. Other options available - please contact sales

Voltage - suitable for 12 or 24V operation: • 4-10014: 10-30VDC supply• 4-10016: 10-40VDC supply

R65 approvals: • 4-10016 and 4-10016-D: Class 1 amber, Class 2 blue,

Class 2 red

Number of LEDs 4 6 2 x 6Dimensions (mm) 90L x 29H x 10D 124L x 31H x 10D 124L x 60H x 10DSupply voltage (DC) 10-30 10-40 10-40Order codesAmber 4-10014-A 4-10016-EA 4-10016-D-EAABlue 4-10014-B 4-10016-EB 4-10016-D-EBBBlue/red (split colour) 4-10014-BR 4-10016-BR 4-10016-D-EBRBlue/white (split colour) 4-10014-BW 4-10016-BW 4-10016-D-EBWAmber/blue (split colour) 4-10014-AB 4-10016-AB 4-10016-D-EAEBRed 4-10014-R 4-10016-ER 4-10016-D-ERWhite 4-10014-W 4-10016-W 4-10016-D-WOther colour combinations available - please contact our sales team for more details4-10033 Optional L mounting bracket for 4-100164-10036 Roof mounted housing for 4-10014/10016

Just 10mm deep

4-10016

4-10014

4-10016-D

Split colour

Half of LEDs are one colour and half are another colour

(LED colour is fixed)

5 YEAR WARRANTY

SEE PAGE

15

Screen and deck mount versions also available

Optional 4-10033 L bracket

4-10036 roof mounted housing

3W LEDs

4-10415 compact 4LED warning light

• Compact but powerful light with 4 or 8 x 3 Watt LEDs• Single, split or dual colours• Heavy duty metal base provides ample heatsinking for

long, reliable LED life • Built-in flasher• Cruise mode - constant low level illumination• Night dim mode• Multiple modules can be synchronised

Flash patterns: • 4-10145: 27 patterns • 4-10145-D: 14 patterns

Variants: • Single colour - four same colour LEDs• Split colours - 2 LEDs (colour 1) + 2 LEDs (colour 2)• Dual colours - 4 dual colour LEDs - light illuminates in

one of the two chosen colours• Independent control of colours

Mounting: • Surface mounting • Recess - with optional 4-1305 rubber bezel

Supply voltage: • 10-40VDC suitable for 12 or 24V operation

R65 approvals - single colour versions: • Class 1 amber or blue • Class 2 red

Dimensions (mm) 120L x 36H x 25DOrder Code Description4-10415-EA 4LED surface mount, R65 Class 1 amber4-10415-EB 4LED surface mount, R65 Class 1 blue4-10415-ER 4LED surface mount, R65 Class 2 red4-10415-x/4-10415-xx 4LED surface mount, green or white or alternating 2+2LEDs (split colour) - all colours4-10415-D-xx 4 dual LED (4 optics) surface mount, dual colour combinations - 4LEDs for each colour4-1305 Recessed mount rubber bezel for 4-10415Clear lenses as standard. Coloured lenses are available to special order - please contact sales for prices

4-10415 with 4-1305 recessed mount rubber bezel

Two LEDs of one colour and two of another

(LED colour is fixed)

All four LEDs operate in the selected colour

(LEDs change colour)

Split colour Dual colour

4-10415

R65 Class 1

R65 Class 1

R65 Class 2

SINGLE, DUAL OR SPLIT COLOURS


R10

5 YEAR WARRANTY

SEE PAGE

14Screen and deck mount versions available

3W LEDs

4-1548 compact 6LED warning light

• Compact, high output light with 6 x 3W LEDS and purpose-designed optic lens

• R65 Class 2 approved in amber, blue and red• Choice of mounting options

Mounting options: • Single hole mount - requires a 20mm hole which acts as

the fixing point and cable entry aperture (suitable for mounting panels up to 5mm deep). Visible depth of just 16mm when fitted

• Surface mount - bezel sits flush against vehicle with no rear protrusions

• Optional 20 degree angle-down moulded rubber mount - directs light downward and compensates for non-vertical mounting surfaces

Supply voltage: • 10-40VDC suitable for 12 or 24V use

R65 approvals:• Class 2 amber, blue or red LEDs

4-1548-SB (surface mount)

4-1548 (single hole mount)

4-1548 with 4-1005 L bracket

Order code Description Dimensions (mm)4-1548-Ex Single hole mount, R65 Class 2 amber, blue or red LEDs 50L x 40H x 34D1/16D24-1548-x Single hole mount, green or white LEDs 50L x 40H x 34D1/16D2

4-1548-SB-Ex Surface mount, black bezel, R65 Class 2 amber, blue or red LEDs 85L x 55H x 26D

4-1548-SW-Ex Surface mount, white bezel, R65 Class 2 amber, blue or red LEDs 85L x 55H x 26D

4-1548-SB-x Surface mount, black bezel, green or white LEDs 85L x 55H x 26D4-1548-SW-x Surface mount, white bezel, green or white LEDs 85L x 55H x 26D4-1005 L bracket for 4-1548 lights (finished in black) 45L x 56H x 31D4-10500 20 degree angled rubber mount for 4-1548 light 90L x 59H x 22D (max)

6-62240 2 x 5A flasher, 18 flash patterns plus cruise and high/low power modesRuns up to 2 lights per output, 10-30V input, 3 year warranty

Standard bezels are black or white - other colours available to order - please contact sales D2

D1

L

H

4-1548-SB fitted with 4-10500 angled

rubber mount


R10

5 YEAR WARRANTY

SEE PAGE

35Designed to work with external flasher

R65 Class 2

R65 Class 2

R65 Class 2

3W LEDs

4-1043/1044/1048 3, 4 & 8LEDdirectional warning lights

Mounting options: • Choice of fixing brackets and bezels available• Surface, L or recessed mount • Double fixing bezels allow modules to be stacked

horizontally (4-1228) or vertically (4-1238)

Supply voltage: • 4-1043/1044: 10-14VDC - 12V use only• 4-1443: requires external 10-40VDC flasher• 4-1048: 10-40VDC - 12 or 24V operation

R65 approvals: • 4-1048: Class 1 amber or blue

3LED modulesDimensions (mm) 69L X 27H x 31D4-1043-x 3LED module with integral flasher, 12V only4-1443-x 3LED module, 10-40V - requires external

flasherMounting options for 4-1043 and 4-14434-1003 L mounting bracket4-1103-B or W Surface mount black or white bezel4-1103-C Surface mount chromed bezel4-1203-B or W Recessed mount black or white bezel4-1203-C Recessed mount chromed bezel4-1303 Recessed mount moulded rubber housingFlasher unit for 4-1443 lights6-62240 2 x 5A flasher, 18 flash patterns plus cruise

and high/low power modes Runs up to 10 x 4-1443 lights per output 10-30V input, 3 year warranty

Please specify required LED and bezel colours when ordering. LED colours: amber, blue, green, red or white Bezel colours: black, chromed or white

4LED modules with integral flasher, 12V onlyDimensions (mm) 55L X 45H X 31D4-1044-x 4LED module 4-1004 L mounting bracket4-1104-B or W Surface mount black or white bezel 4-1104-C Surface mount chromed bezel4-1204-B or W Recessed mount black or white bezel4-1204-C Recessed mount chromed bezel4-1304 Recessed mount moulded rubber housing

8LED modules with integral flasher, 10-40VDimensions (mm) 100L x 45H x 31D4-1048-EA/EB 8LED module - R65 Class 1 amber or blue4-1048-x 8LED module - green, red or white4-1048-xx 8LED split colour - all colours, 4+4LEDs

alternating4-1048-IR 8LED infrared 840-870nm or 930-960nm4-1008 L mounting bracket4-1108-B or W Surface mount black or white bezel4-1108-C Surface mount chromed bezel

4-1208-B or W Recessed mount black or white bezel4-1208-C Recessed mount chromed bezel4-1228-B, C or W Recessed mount double bezel (horizontal)4-1238-B, C or W Recessed mount double bezel (vertical)4-1308 Recessed mount moulded rubber housing

4-1048 with 4-1108-C surface bezel

4-1044 with 4-1104-B surface bezel

4-1043 with 4-1203-C recessed bezel

4-1303 recessed rubber bezel

2 x 4-1048 with 4-1238-B recessed double bezel (vertical)

4-1048 with L bracket and

4-1108-B bezel

4-1308 recessed

rubber bezel

All bezels are supplied with gasket and mounting plate

• Versatile, ultra-bright 3, 4 and 8 x 3W LED lights• Single, split colour and infrared versions• Multiple modules can be synchronised• 8LED variant (4-1048) R65 approved • Night dim mode

2 x 4-1048 with 4-1228-C recessed double bezel (horizontal)



R10

5 YEAR WARRANTY

R65 Class 1

R65 Class 1

3W LEDs

4-10409 Impact 9LED directional warning light

Mounting:• Simple surface fixing

Options: • Choice of LED and bezel colours - see table below

Materials: • Lens and bezel: strong UV stabilised polycarbonate

Supply voltage: • 10-40VDC suitable for 12 or 24V use

R65 approvals: • Class 2 amber or blue

• Highly effective optical lens design with wide angle light output • 3 independent groups of 3 LEDs - can be single colour or

alternating colours • Built-in flash controller with 17 flash patterns • Night dim mode• Multiple modules can be synchronised• R65 Class 2 approved in amber or blue

Dimensions (mm) 182L x 77H x 38D (7”x 3”x 1.5”) Order Code Description4-10409-EA 9LED R65 Class 2 amber 4-10409-EB 9LED R65 Class 2 blue 4-10409-xxx 9LED green, red, white or mixed colours, 3+3+3 LEDs alternating Please specify LED and bezel colours when ordering LED colours: amber, blue, green, red or whiteBezel colours: black, chromed, white or yellowLens colours: clear as standard - amber, blue or red available to order - please contact our sales team for prices

R65 Class 2

R65 Class 2

SINGLE OR MIXED COLOURS

3W LEDs


R10

5 YEAR WARRANTY

SEE PAGE

30Matching angle down scene light available

4-10418 8LED wide angle directional warning light

• High output LEDs and purpose-designed optic lens distribute light evenly over a wide 180 degree angle

• Fully weatherproof, suitable for exterior use• Integral flasher• Cruise mode - constant low level illumination• Night dim mode• Multiple modules can be synchronised• R65 Class 2 approved

Mounting options: Light is supplied mounted in a neat surface mount, cast metal housing, or can be used in conjunction with a choice of additional fixing brackets:• 4-10001 - fixed surface mount - does not require access

to the rear of the light for fixing• 4-10002 - adjustable surface mount bracket - allows the

light to be angled up or down. Can be mounted on each corner of a vehicle to provide 360 degree warning light

• 4-10003 - allows the light to be angled up or down but is designed to fix the lights at a 45 degree angle. Ideal for motorcycle applications, allowing a pair of lights to each point out at 45 degrees and provide full intensity coverage over 180 degrees (see illustration below)

Supply voltage: • 10-40VDC suitable for 12 or 24V operation

R65 approvals: • Class 2 amber, blue and red LEDs

4-10418 dimensions (mm) excluding bracket 155L x 32H x 48D4-10418-S dimensions (mm) 184L x 34H x 50D

Order code (separate bracket type)

Order code(cast housing - no bracket required)

Description

4-10418-EA-F 4-10418-S-EA-F 8LED wide angle warning light, amber LEDs R65 Class 2

4-10418-EB-F 4-10418-S-EB-F 8LED wide angle warning light, blue LEDs R65 Class 2

4-10418-ER-F 4-10418-S-ER-F 8LED wide angle warning light, red LEDs R65 Class 2

4-10418-BR-F 4-10418-S-BR-F 8LED wide angle warning light, split colour (4+4LEDs) blue/red LEDs

4-10418-x-F 4-10418-S-x-F 8LED wide angle warning light, green or white LEDs

Mounting brackets (order in addition to 4-10418 lights)4-10001 Surface mount bracket4-10002 U bracket mounting assembly (with vertical swivel)

4-10003 U bracket 45 degree angle mounting assembly (with vertical swivel)

4-10418-S

4-10418 + 4-10001

4-10418 + 4-10003

4-10418 + 4-10002

H

D

L

2 x 10418 lights arranged to provide 180 degree full intensity coverage using 4-10003 brackets

R65 Class 2

R65 Class 2

R65 Class 2



R10

5 YEAR WARRANTY

3W LEDs

4-2033/2034/2053 surface mount warning lights

Dimensions (mm) 99L x 38H x 28D Order Code Description4-2033-A 3LED warning light - amber LEDs, black bezel4-2033-B 3LED warning light - blue LEDs, black bezelOther colours are available to order - please contact our sales team

4-2033 3LED surface mount warning light

• 14 patterns using built-in flasher• Easy installation via neat plastic bezel

using just two screws• Synchronise multiple lights• 10-30VDC supply - for 12 or 24V use

Dimensions (mm) 83L x 25H x 19D Order Code Description4-2053-EA 3LED warning light - R65 Class 1 amber, black bezel4-2053-EB 3LED warning light - R65 Class 1 blue, black bezel4-2053-R 3LED warning light - red, black bezel4-2303 Recessed mount moulded rubber housing for 4-2053

• R65 approved - Class 1 amber or blue• Built-in flasher with 20 flash patterns • Cast metal bezel secures the light in position using two

screws and provides excellent heatsinking to maximise LED performance

• 10-30VDC supply range (suitable for 12 or 24V use)• IP67 rated - suitable for harsh environments• Multiple lights can be synchronised for simultaneous

or alternating flash

Dimensions (mm) 120L x 38H x 28D Order Code Description4-2034-A 4LED warning light - amber LEDs, black bezelOther colours are available to order - please contact our sales team for assistance

4-2034 4LED surface mount warning light• Built-in flasher with choice of 24 patterns • Amber LEDs as standard - other colours available to

order• 10-30VDC supply range (suitable for 12 or 24V use)• Multiple units can be synchronised

4-2053 3LED surface mount warning light

4-2303 recessed mount rubber housing for 4-2053

R65 Class 1

R65 Class 1


R10

2 YEAR WARRANTY

3W LEDs

3W LEDs

3W LEDs

4-10446/10479 large format8 & 16LED warning lights

• Powerful light output particularly for large vehicles• Single or split colours• Low profile design for unobtrusive surface mounting• Built-in flasher with choice of 12 flash patterns• Cruise mode - constant low level illumination• Night dim mode• Multiple units can be synchronised

Mounting:• Easy surface mount installation using just two or four

screws - no need to cut holes in bodywork

Voltage: • 10-40VDC supply for 12 or 24V operation

R65 approvals: • 4-10446: Class 2 amber, blue or red• 4-10479: Class 2 blue

4-10446 (6” x 4”)Dimensions (mm) 150L x 100H x 24D Order Code Description4-10446-EA 8LED 6” x 4” surface mount R65 Class 2 amber4-10446-EB 8LED 6” x 4” surface mount R65 Class 2 blue4-10446-ER 8LED 6” x 4” surface mount R65 Class 2 red4-10446-xx 8LED 6” x 4” surface mount split colours - all colours4-10446-x 8LED 6” x 4” surface mount green or white4-10479 (9” x 7”) Dimensions (mm) 228L x 176H x 25D Order Code Description4-10479-A 16LED 9” x 7” surface mount amber4-10479-EB 16LED 9” x 7” surface mount R65 Class 2 blue4-10479-xx 16LED 9” x 7” surface mount split colours - all colours4-10479-x 16LED 9” x 7” surface mount green, red or whitePlease specify lens and bezel colours when orderingLens colours: clear as standard - amber, blue or red available to special orderBezel colours: black or chromed

4-10446 (black)

4-10479 (chrome)

4-10479 (black)

R65 Class 2

R65 Class 2

R65 Class 24-10446

R65 Class 24-10479

4-10446 (chrome)



R10

5 YEAR WARRANTY

3W LEDs

4-1601 rubber bezel

• Low profile design• Single split or dual colours• Supplied with multiple mounting brackets to cover most applications• Integral flasher with numerous flash patterns (see table)• Synchronise up to eight lights

4-1641/1642/1643 slim6 & 12LED warning lights

Features:• High power LED lights with enhanced output from linear

optic on 4-1642 and 4-1643• 4-1643 has 12 LEDs, providing dual colour output. The

complete light operates in the selected colour • On 4-1643-D variants, the light alternates between

colour 1 and colour 2; on 4-1643-DI models, each colour is independently controlled via a separate trigger wire

IP rating: • All versions protected to IP67 - suitable for harsh

environments

Mounting:• Direct surface mounting • Surface or lip mount brackets for panel or grille edge

mounting, allowing the light to be tilted• Flush mount using optional 4-1601 rubber mount

Voltage: • 10-30VDC supply for 12 or 24V operation

R65 approvals: • Class 1 amber, Class 1 blue

Dimensions (mm) 130W x 24H x 17.5D 4-1641 6LED single colour low profile warning light with TIR optic - designed for horizontal mounting 29 flash patterns4-1641-EA Universal mount, R65 Class 1 amber4-1641-EB Universal mount, R65 Class 1 blue4-1641-R Universal mount, red4-1641-W Universal mount, white4-1601 Flush/recess mount moulded rubber housing for 4-16414-1642 6LED single colour low profile warning light with linear optic - designed for horizontal mounting 29 flash patterns4-1642-A Surface mount, amber 4-1642-B Surface mount, blue4-1642-X Surface mount, red, white or split colour combinations - please specify when ordering4-1601 Flush/recess mount moulded rubber housing4-1643 12LED dual colour surface mount low profile warning light with linear optic -DI versions allow independent control of each colour Flash patterns: -D models 29, -DI models 814-1643-D-XX Dual colour - amber/red, blue/red or blue/white4-1643-DI-XX Dual colour with independent switching

Surface mount bracket

Lip mount bracket

4-1642/1643

4-1641

R65 Class 1

R65 Class 1



R10

5 YEAR WARRANTY

3W LEDs

4-1641-V produces a wide horizontal beam spread when

mounted vertically

Normal warning lights produce a very narrow horizontal beam when

mounted vertically

4-1641-V slim vertical mount 6LED warning light

Design features:When mounted on a vertical axis, the special optical design ensures light is distributed correctly in accordance with R65 requirements. In contrast, conventional warning lights designed to be mounted only on a horizontal axis produce a very narrow horizontal beam spread when mounted vertically.

Mounting options:• Surface mount• Flush or recess mount with optional moulded rubber housing• Also available as a number plate mounted light (models 5-7066/7166)

Voltage:• 10-30V suitable for 12 or 24V use

IP rating: • IP67 rated - suitable for harsh environments

R65 approvals: • Class 2 amber or blue

• Purpose designed and R65 Class 2 approved for vertical mounting• Wide horizontal beam spread• Very low profile design• Built-in flasher with 12 patterns• Night dim mode• Synchronise up to eight units

Dimensions (mm) 130H x 24W x 17.5D 4-1641-V 6LED low profile warning light (TIR optic) - designed for vertical mounting Order code Description4-1641-V-EA 6LED vertical mount, R65 Class 2 amber4-1641-V-EB 6LED vertical mount, R65 Class 2 blue4-1641-V-R 6LED vertical mount, red4-1641-V-W 6LED vertical mount, white 4-1601 Flush/recess mount moulded rubber housing

R65 Class 2

R65 Class 2


R10

5 YEAR WARRANTY

3W LEDs

5-7064/7066/7164/7166 number plate mounted lights

• 4 & 6LED front number plate mounted warning lights• Synchronised sideways and forward warning light for excellent

visibility when emerging at junctions• Ideal for covert applications• 6LED version R65 approved Class 2 in amber or blue

Choice of beam spreads:• 4-10014: 4LED warning lights - vertical spread • 4-1641-V 6LED warning lights - horizontal spread

Mounting options:• 5-7064/7066: mount the two housings to each end of the

number plate• 5-7164/7166: mounts behind the number plate. To

install, remove the number plate, fit the light to the plate and refit the plate in the original position

All fixing holes are covered by the number plate.

Voltage:• 10-30V suitable for 12 or 24V use

R65 approvals: • 4-1641-V versions (5-7066/7166): Class 2 amber or blue

4-10014

Order code DescriptionFront number plate end housing type Dimensions (mm): 140H x 79L x 36D5-7064-x Pair of end housings with 4-10014 4LED warning lights - amber, blue, red or white LEDs5-7066-EA/EB Pair of end housings with 4-1641-V 6LED warning lights - R65 Class 2 amber or blue5-7066-x Pair of end housings with 4-1641-V 6LED warning lights - red or white LEDsFront number plate plinth type Dimensions (mm): 140H x 619L x 39D5-7164-x Number plate mounted system with 2 x 4-10014 4LED warning lights - amber, blue, red or white LEDs5-7166-EA/EB Number plate mounted system with 2 x 4-1641-V 6LED warning lights - R65 Class 2 amber/blue5-7166-x Number plate mounted system with 2 x 4-1641-V - 6LED warning lights - red or white LEDsPlease replace -x with required LED colour (A, B, R or W)

4-1641-V

5-7064/5-7066 number plate end housing

5-7164/5-7166 number plate plinth

R65 Class 2

R65 Class 2


R10

5 YEAR WARRANTY

3W LEDs

3W LEDs


• Compact, powerful screen/deck mount versions of 4-10415 lights (see page 4)

• Single, dual or split colours• Built-in multi-pattern flasher• Ventilation slot aids airflow and demisting• Triple suction cups for secure fixing• Cruise mode on 4-1065 versions • Night dim mode (switch dependent)

Mounting options:• 4-1055: windscreen mount. Supplied with light shield,

suction mounts and lead with switched options and fused cigar plug

• 4-1065: dash/deck or permanent mount. Supplied with light shield, suction mounts and 1.5 metre lead with wiring options for pattern change, high/low intensity, synchronisation, cruise mode and colour selection (on split or dual colour types)

• Easily adjust reach and angle to suit the design of the vehicle

Voltage: • 10-40V supply range (suitable for 12 or 24V use)• 4-1055 versions are available with a pattern change

button or can be ordered with a preset fixed pattern

R65 approvals - single colour versions: • Class 1 amber or blue • Class 2 red

4-1055/1065 4LED screen/deck mount lights

4LED windscreen mount light27 patterns on single or split colour combinations; 14 patterns on dual colour combinationsDimensions (mm) 154W x 130D x 41HOrder code Description4-1055-I-x/xx 4LED single colour, with single switch lead

4-1055-P-x/xx 4LED single colour, with double switch lead for pattern change. Also available in green or white, or split colour LEDs (2 + 2 - please specify required colours)

4-1055-S-xx 4LED split colour, with double switch lead for individual colour selection4-1055-D-P-xx 4 dual LED, dual colour, with double switch lead for pattern change4-1055-D-S-xx 4 dual LED, dual colour, with double switch lead for individual colour selection4LED deck or rear screen mount lightDimensions (mm) 154W x 130D x 41HOrder code Description4-1065-x/xx 4LED deck/rear screen mount. Also available in green, white or split colour options 4-1065-D-xx 4 dual LED deck/rear screen mount, dual colour - amber/blue or blue/redPlease replace x with required colour(s) when ordering

4-1055-I

Half of LEDs are one colour and half are another (LED colour is fixed)



R65 Class 1

R65 Class 1

R65 Class 2


R10

5 YEAR WARRANTY

3W LEDs

4-1056/1066/1067 6 & 12LEDscreen/deck mounted lights

• Single, dual or split colour options• Built-in flasher with numerous flash patterns• Ventilation slot aids airflow and demisting• Triple suction cups for secure fixing

Variants:• 6LED lights are screen mounted variants of the 4-10016

warning light with cruise and dim modes (see page 3)• 12 LED lights are screen mounted variants of the

4-10026 dual colour light with dim mode (see page 2)• 4-1056 versions are available with a pattern change

button or can be ordered with a preset fixed pattern • Dual colours alternating or independent switching of

each colour

Mounting options:• 4-1056: screen mount. Supplied with light shield, suction

mounts and lead with switched options and fused cigar plug

• 4-1066/1067: dash/deck or permanent mount. Supplied with light shield, suction mounts and 1.5 metre lead with wiring options for pattern change, high/low intensity, synchronisation and colour selection (split/dual colour versions)

• Reach and angle are easy to adjust

Voltage: • 10-40V supply range (suitable for 12 or 24V use)

R65 approvals: • Please see table

Windscreen mount - with full depth visor 27 flash patterns Dimensions (mm) 154W x 130D x 41HOrder code Description R65 certification4-1056-I-x/xx 6LED single colour with single switch lead Class 1 amber, Class 2 blue, Class 2 red

4-1056-P-x/xx 6LED single colour with double switch lead for pattern change. Also available in split colour LEDs (3 + 3) - non R65 Class 1 amber, Class 2 blue, Class 2 red

4-1056-S-xx 6LED split colour (3 + 3 LEDs) with double switch lead for individual colour selection -

4-1056-D-I-xx 12LED dual colour - one button per colour Class 2 amber and Class 2 blue

4-1056-D-P-xx 12LED dual colour - one button activates lights in dual colour mode/one button for pattern selection Class 2 amber and Class 2 blue

Dash/deck mount - with full depth visor Dimensions (mm) 154W x 130D x 41H4-1066-x/xx 6LED single colour. Also available in split colours (non R65) Class 1 amber, Class 2 blue, Class 2 red4-1066-D-xx 12 LED dual colour Class 2 amber and Class 2 blueRear screen mount - with reduced depth visor 8 flash patterns Dimensions (mm) 154W x 48D x 41H

4-1067-x/xx 6LED single colour with single switch lead. Also available in split colours (non R65) Class 1 amber, Class 2 blue, Class 2 red

4-1067-D-xx 12LED dual colour Class 2 amber and Class 2 blueLED colours: R65 amber, R65 blue, green, red or white - please specify LED colours when ordering

4-1056-I

Half of LEDs are one colour and half are another (LED colour is fixed)



The 4-1067’s shortened visor is designed for mounting onto vertical or near vertical rear screens

4-1066-I

R65 Class 2

R65 Class 1

R65 Class 2

R65 Class 2SINGLE, DUAL OR

SPLIT COLOURS


R10

5 YEAR WARRANTY

3W LEDs

4-2060 4+4LED screen mount light

• Low cost but powerful 4+4LED windscreen light• Single colour or amber, blue or red (4+4LED) combinations • Built-in flasher with 20 patterns • Linear optic projects a uniform warning signal

4-2060

Dimensions (mm) 237W x 130D x 41HOrder Code Description4-2060-xx Dual 4+4 LED modules - amber, blue or red combinations, 12V

Mounting options:• Supplied with cigar plug• Triple suction cups for secure fixing • Easily adjust reach and angle to suit the design of the

vehicle

Voltage:• 10-16VDC for 12V operation


R10

2 YEAR WARRANTY

3W LEDs

2 YEAR WARRANTY4-1430 4LED hideaway lightwith built-in flasher• Powerful single or split colour (2+2) LED hideaway button light • Flash controller built into the light head for easy fitting• Unobtrusive flush mounting - rubber bezel just 5.5mm deep• Multiple lights can be synchronised• Night dim mode• 14 flash patterns 4-1430 with flush

mount rubber bezel

Mounting:• Supplied with rubber bezel for unobtrusive flush

mounting and two lugs allowing the light to be screw mounted. Max 30mm diameter cut-out required

• Optional 4-1504 metal L bracket

Voltage:• 12V• Maximum current: 1.7A at 12VDC

Dimensions (mm): 40L x 28HDiameter: 35mm (with bezel) 29mm (without bezel)Order Code Description4-1430-x/xx 12W 4LED hideaway light with bezel and mounting lugs 4-1504 Optional stainless steel metal L bracket

LED coloursSingle colours - Amber, blue, red or white Split colours (2+2) - Blue/red or blue/whitePlease replace -x with required LED colour(s) when ordering


With optional 4-1504 stainless steel L mounting bracket

With two hole screw mount

R10

4-1420 LED hideaway unit

4-1420 single light head

Flasher dimensions (mm) - see diagram for head dimensions: 4-1420/4-2420: 115L x 29H x 19D 4-2422: 85L x 62H x 29D

Order Code Description

4-1420-xx 12W LED hideaway directional light4-2420-x Linked pair of 12W LED hideaway directional lights (common flasher)

4-2422-x/xPair of 12W LED hideaway directional lights with common flasher. Split colours (2 + 2 LEDs per head) - amber, blue, green, red or white, each colour separately switched/independently controlled

Please replace -x with required LED colour (A, B, R or W) when ordering

• Powerful output from 4x3W LEDs per light head• In-line flash controller with plug and socket connector and multiple patterns• 4-2422 has dual colour heads with separate switching of each colour• Synchronise multiple units for simultaneous or alternating flash• IP65 water ingress protection - suitable for use in a wide range of operating

environments

Surface bezel fixing

Mounting:• Standalone or integrate within the vehicle lighting• Plastic surface mount bezel and metal L bracket supplied as standard • Can also be mounted in headlight

Voltage:• 10-30V supply

4-2420/4-2422 linked pair with common flasher

38mm diameter

25mm

7mm

18mm

57mm

49mm

L bracket fixing3W LEDs


R10

3 YEAR WARRANTY


R10Interior vehicle lights

4-54100/54150/54300/54600• 16, 31, 61 & 121LED lights in lengths from

100-600mm• Simple surface fixing• 12 or 24V versions - specify when ordering

4-6220 rectangular LED interior light• Operating temperature -20oC to +60oC• 4W consumption• 64 SMD LEDs - 140 Lumen output• 12 or 24V operation • Dual levels touch to select off/dim/high

(last setting is memorised on switch-off)

4-6221 rectangular LED interior light• Operating temperature -20oC to +60oC• 4W consumption• 60 SMD LEDs - 140 Lumen output• 12 or 24V operation • Dual levels touch to select off/dim/high

(last setting is memorised on switch-off)

4-7343 rectangular LED interior light• 3 high output white Generation 3 LEDs• Optical lens maximises light distribution• Durable polycarbonate lens and base• Simple surface mount with 2 wire connection• 10-30V supply for 12/24V operation• 0.4A current consumption@13V

4-7612/7614 12” (304mm) Flexi-Map light mount• Halogen or LED models• Sliding red filter• On/off/dimmer switch• 12 or 24V

Order code

Description Dimensions (mm)

4-54100 16LED interior light* 100L x 25W x 10D4-54150 31LED interior light* 150L x 25W x 10D4-54300 61LED interior light* 300L x 25W x 10D4-54600 121LED interior light* 600L x 25W x 10D4-6220 LED interior light, 12/24V 185L x 150W x 12D4-6221 LED interior light, 12/24V 220L x 100W x 12D4-7343 LED interior light, 12/24V 178L x 83W x 18D4-8031 8” diameter dual bulb dome light, 12V

Add -B to product code for blue lens4-7612-T Halogen 12” Flexi-Map light mount*4-7614-T LED 12” Flexi-Map light mount** Please specify 12V or 24V when ordering

4-7612/4-7614

4-54300

4-6220

4-6221

4-7343

1 YEAR WARRANTY

NEW


R10 5-355X-3560 programmable LED Arrowbars/warning bars

5 YEAR WARRANTY

8-82304

• Slimline Arrowbar/warning bar - just 28mm deep• Lengths from 558 to 1386mm (20.5 to 54.5 inches)• 4 to 10 x 6LED modules featuring powerful 3 Watt LEDs• Built-in flasher with choice of single, double and quad flash patterns• Can be mounted vertically or horizontally using the adjustable brackets• R65 certified to Class 1 amber, Class 2 blue or Class 2 red modules• Night dim option

Order code DescriptionSlimline Arrowbar with 6LED modules R65 certified in Class 1 amber, Class 2 blue, Class 2 red or non R65 green or white 10-40VDC suitable for 12 or 24V operation Dimensions: 35mm high x 28mm deep5-3554 20.5 inch (558mm) 4 module 24LED Arrowbar5-3556 33 inch (830mm) 6 module 36LED Arrowbar5-3557 38 inch (969mm) 7 module 42LED Arrowbar5-3558 43.5 inch (1108mm) 8 module 48LED Arrowbar5-3558-A6B2 43.5 inch (1108mm) 8 module 48LED Arrowbar, 6 x R65 Class 1 amber + 2 x Class 2 blue (or Class 2 red) modules5-3559 49 inch (1247mm) 9 module 54LED Arrowbar5-3559-A7B2 49 inch (1247mm) 9 module 54LED Arrowbar, 7 x R65 Class 1 amber + 2 x Class 2 blue (or Class 2 red) modules5-3560 54.5 inch (1386mm) 10 module 60LED Arrowbar5-3560-A8B2 54.5 inch (1386mm) 10 module 60LED Arrowbar, 8 x R65 Class 1 amber + 2 Class 2 blue (or Class 2 red) modulesArrowbars are supplied with built-in flasher and are compatible with a wide range of switching controllers where required6-63101 Arrowbar switch panel - 1 year warranty6-63102 Deluxe Arrowbar controller - 1 year warranty8-82304 4 button EuroSmart handset with quick release magnetic mount and 1.2m cable - 2 year warranty

8-82306 6 button EuroSmart handset with integral microphone, quick release magnetic mount and plug-in coiled lead, CANbus - 2 year warranty

3W LEDs

R65 Class 2

R65 Class 1

R65 Class 2

• The bar has 4 fully programmable flash activation wires. Each wire can be set to trigger any of 30 different arrow / warning patterns

• Up to 4 separate patterns can be stored in the flasher - a typical configuration might be: Pattern 1: arrow left Pattern 2: arrow right Pattern 3: centre out Pattern 4: warning pattern Many alternative configurations can be programmed

• If preferred, the two end modules can be programmed to emit a continuous warning pattern operating completely independently from the inner module arrowbar function

8-82306

6-63101

6-63102

See brochure

3


R10Multi-module warning& Arrowbars

Multi-module bars are available in 2 to 14 module configurations, with 3LEDs per module, and almost any combination of LED colours. • 2-4 module units have integral flasher with a choice of

programmable warning patterns and synchronisation options

• 8-14 module bars have extra functionality and can be used as warning lights or programmed as arrowbars (to direct traffic) with either integrated or separate warning functions

• 8-14 module units without FP in the part number have three separate, individually programmed flash sequence modes. Any of the three modes can be activated by applying a 12V signal to the appropriate trigger wire

• A flash mode can be a warning pattern, an arrow pattern or a combination of arrow pattern followed by a warning pattern (all as one cycle). Any of the programmed modes can be re-programmed at any time

• Units with FP in the part numbers have four trigger wires instead of three, preconfigured for arrow left, arrow right, centre out and warning pattern (side to side alternating using all modules). FP range bars cannot be reconfigured

Mounting options:• Supplied with mounting brackets for vertical or

horizontal mounting, bolts and wiring loom. The brackets include mounting holes which allow the bar to be tilted to direct light output

• For ease of installation, all versions and sizes can be supplied in split configuration with linking cable

Voltage:• Suitable for 12 or 24V operation

• Lengths from 160 to 975mm (6 to 38”)• Single or multiple colour options• Longer lengths can be split with interconnecting wiring• Can operate as warning, arrowbar or combined warning/arrowbar units

Multi-module warning bars (without arrow patterns)Dimensions (mm) 30H x 45D Order code Description4-3442-xx 160mm long, 2x3LED modules 4-3443-xxx 240mm long, 3x3LED modules 4-3444-xxxx 322mm long, 4x3LED modulesMulti-module warning bars and arrowbars (with arrow patterns)5-3448-x8 25” (644mm) - 8x3LED modules (configuration A)5-3448-x4x4 25” (644mm) - 8x3LED modules (configuration B - 4 inner plus 4 outer modules or configuration C)5-3448-x6x2 25” (644mm) - 8x3LED modules (configuration B with 6 inner and 2 outer)5-34410-x10 32” (810mm) -10x3LED modules (configuration A)5-3448+2-x8x2 32” (810mm) - 10x3LED module (configuration D with 8 inner plus 2 outer modules)5-34412 -x12 38” (975mm) - 12x3LED modules (configuration A)5-3448+4-X8X4 38” (975mm) - 12x3LED module (configuration D with 8 inner plus 4 outer modules)5-34410+4- X10X4 45” (1140mm) - 14x3LED module (configuration D with 10 inner plus 4 outer modules)5-3448-X8-FP 25” (644mm) - 8x3LED modules (configuration E) 5-3448+2-X8X2-FP 32”(810mm) - 10x3LED modules (configuration F) 5-3448+4-X8X4-FP 38” (975mm) - 12x3LED modules (configuration F) Notes:1) When ordering please specify the required configuration (A-F - see facing page)2) Choice of amber, blue, green, red or white LEDs - please replace X with required LED module colours in above part numbers

4-3444 4 module unit

5-34412 12 module Arrowbar

5 YEAR WARRANTY


R10

6-63101

6-63102

All Arrowbars are supplied with built-in flasherPlease order Arrowbar controllers separately if required1 year warrantyOrder Code Description6-63100 Sequential three pattern LED Arrowbar flasher with harness, 12/24V, 8 output (10-40V)6-63101 Arrowbar switch panel, three patterns plus on/off6-63102 Deluxe controller for operation of 5-3448 series Arrowbars, on/off plus selection of 4 patterns (arrow left,

right or centre out or warning)

Multi-module warning & Arrowbars

Configuration AAll LED modules are the same colour. Unit has three separately programmable modes. Each mode can be a warning pattern, arrow pattern or combined warning and arrow pattern. Normally configured to display combined warning and arrow patterns whereby inner modules are displayed as an arrow pattern before flashing the two outer modules as a warning pattern, then repeating. All three modes are stored in separate memories and can be activated at any time by applying a positive signal to the relevant trigger wire.

Configuration BGenerally as configuration A except one or two outer modules at each end are a different colour to inner modules.

Configuration DInner modules operate as configuration A. In addition, two or four outer modules are provided (one or two at each end) which are wired separately and operate completely independently of inner modules. A separate flash controller is required (e.g. 6-62240) for flashing of outer modules.

Configuration CGenerally as configuration A except that units incorporate two different colour LED modules, arranged with differing colour lights left and right.

Configuration EAll LED modules are the same colour, four separate fixed modes, each with a separate trigger wire. Modes are arrow left, arrow right, centre out and side-to-side warning pattern.

Configuration FInner modules operate as configuration E. In addition, two or four outer modules are provided (one or two at each end), these are wired separately and operate completely independently of inner modules. A separate flash controller is required (e.g. 6-62240) for flashing of outer modules.

45mm

166mm

26mm

81mm

44mm

16mm

7mm


R105-9305/9405/9406 LED InfoSigns

• Weatherproof design• Choice of 70 or 110mm high characters• Amber or red high intensity LEDs (see table)• Large memory - stores up to 99 messages• Back-lit LCD display on controllers for ease of message selection and validation

• Display up to 8 or 9 characters without scrolling • Create and store up to 99 messages plus functions such

as scroll, flash and wipe using Haztec Windows software • Create custom bitmap symbols

Operation:• Select the required message from the library and

activate with the push of a button. The active message is also shown as a confirmation on the handset

• Multi-line display on controller shows the current message and allows the user to scroll through the library and preselect the next message; brightness of the message sign and controller screen can also be adjusted

Mounting:• Supplied as a complete kit including mounting brackets,

bolts, wiring loom and controller• 9-9305 versions are suitable for fitting in Haztec Xpress

lightbars - please see lightbar brochure

Options:• Electrically controlled flip-up versions (suitable for

interior vehicle use only)

Voltage:• 12V as standard. Please contact sales for 24V options

5-9305 9 x 70mm high character InfoSign Dimensions (mm) 464L x 86H x 50D5-9305-99-x Programmable LED message sign with back-lit LCD 99 message controller - amber or red LEDs5-9305-F-99-R Flip-up programmable LED message sign with back-lit LCD 99 message controller - red LEDs only5-9301-V2 Programming software and USB data lead for 5-9305-99 InfoSign5-9305-99-CTR 99 message programmable LCD controller for 9305-995-9405 8 x 110mm high character InfoSign Dimensions (mm) 510L x 140H x 42DOrder code Description5-9405-16-R Programmable LED message sign with back-lit LCD 16 message controller - red LEDs only5-9405-F-16-R Flip-up programmable LED message sign with back-lit LCD 99 message controller - red LEDs only5-9405-99-R Programmable LED message sign with back-lit LCD 99 message controller - red LEDs only5-9405-F-99-R Flip-up programmable LED message sign with back-lit LCD 99 message controller - red LEDs only5-9402-99 Programming software and USB data lead for 5-9405-99 InfoSign5-9405-99-CTR 99 message programmable LCD controller for 9405-995-9406 9 x 110mm high character InfoSign Dimensions (mm) 573L x 142H x 45D Order code Description5-9406-99-x Programmable LED message sign with back-lit LCD 99 message controller - amber or red LEDs5-9406-F-99-x Flip-up programmable LED message sign with back-lit LCD 99 message controller - amber or red LEDs5-9403-99 Programming software and USB data lead for 5-9406-99 InfoSign5-9406-99-CTR 99 message programmable LCD controller for 9406-99Please specify LED colour when ordering

Controller with backlit LCD display and illuminated buttons

to aid night-time useFlip-up InfoSign with 5-9406

5-9305 in Xpress lightbar

5-9305 InfoSign

5-9406 InfoSign

2 YEAR WARRANTY


R10

7-1211/12/22 linear bar lights

Order code Description Output(Lumens) Beam details Dimensions

(mm)7-1211-40-8-F 8’’ (200mm) 40W single row flood beam 3400 45° Flood 90D x 70H7-1211-40-8-S 8’’ (200mm) 40W single row spot beam 3400 15° Spot 90D x 70H7-1212-120-20-C 20’’ (520mm) 120W sgl row combination beam 10200 45° + 15° + 45° Flood/Spot/Flood 90D x 70H7-1212/240-40-C 40’’ (1010mm) 240W sgl row combination beam 20400 45° + 15° + 45° Flood/Spot/Flood 90D x 70H7-1212-300-49-C 49’’ (1240mm) 300W sgl row combination beam 25500 45° + 15° + 45° Flood/Spot/Flood 90D x 70H7-1222-72-14-C 14’’ (342mm) 72W dbl row combination beam 5760 60° + 30° +60° Flood/Spot/Flood 80D x 82H7-1222-180-32-C 32’’ (810mm) 180W dbl row combination beam 14400 60° + 30° +60° Flood/Spot/Flood 80D x 82H7-1222-234-42-C 42’’ (1044mm) 234W dbl row combination beam 18700 60° + 30° +60° Flood/Spot/Flood 80D x 82H7-1222-288-50-C 50’’ (1278mm) 288W dbl row combination beam 23040 60° + 30° +60° Flood/Spot/Flood 80D x 82H

7-5430 dual mount 10LED worklight

• Ideal for applications requiring large amounts of light• Powerful Cree LEDs • Single or double row• IP67 rated

Dimensions (mm) 150 x 80 x 38D (excluding bracket)Order code Description7-5430-F 15W LED floodlight (60 degrees), 9-32V

• 15W LED floodlight with 10 powerful Osram LEDs • Can be mounted vertically or horizontally • 60 degree angle• IP67 rated suitable for harsh environments

• 10 x Osram LEDs running at low individual current maximise LED efficiency and produce a very uniform beam

• 1375 Lumen output - typically 30-40% higher than most low cost 15W LED worklights, but with a current consumption of just 1.25A @ 12V / 0.625A @ 24V

Mounting options:• Vertical or horizontal - suitable for a variety of locations

using stainless steel mounting brackets supplied

Voltage:• 9-32VDC supply suitable for 12/24V operation

7-1212-300-49-C7-1222-234-42-C

• Units are rated from 40-288W, with a maximum output of over 25,000 Lumens, sufficient for the most demanding of tasks. Please see table below for individual outputs

• Choice of spot, flood or combination beams. Combination beam versions are normally divided into three sections, flood/spot/flood, giving an excellent combination of both short and long range performance

Mounting options:• Supplied with mounting feet that slide along the body of

the light for ease of installation. Mounting brackets allow the light to be angled up or down

Voltage:• 10-30VDC supply suitable for 12 or 24V operation

1 YEAR WARRANTY

2 YEAR WARRANTY

General purpose LED worklights

• Rugged and weatherproof• Latest LED technology• Long life and low current drain• Typical working life of 30,000 hours

Haztec supplies a wide range of LED worklights which offer high light output with low current drain in comparison with earlier halogen technologies. With a choice of power outputs and beam patterns, there are lights for every requirement - from the compact 7-1418, which is available with a choice of flood or concentrated beams, to the very high 3800 Lumen output 7-1048.With the exception of the 7-1110 compact unit, all lights incorporate multiple LEDs.

The range includes optics designed for short range, wide angle illumination, with other models providing an excellent combination of short range beam spread or long range performance. All lights in the range are suitable for 12 or 24V operation and feature stainless steel mounting brackets and bolts.

Order code Shape/Type Dimensions (mm) excl mount bracket Watts Beam Beam angle

(degrees) Lumens

7-1009-F Rectangular 112W x 81H x 56D 9W Flood 90 5407-1015-F Square 110W x 128H x 46D 15W Flood 60 1200 7-1018-C Round 116W x 128H x 48D 18W Concentrated 30 14007-1418-F Rectangular 150W x 45H x 59D 18W Flood 60 14007-1418-S Rectangular 150W x 45H x 59D 18W Concentrated 30 14007-1027-C Square 106W x 128H x 55D 27W Concentrated 30 22007-1048-F Square 110W x 127H x 72D 48W Flood 60 38007-0000-CW Magnetic mount option with coil lead and switched plug for work lights

7-1009-F

7-1015-F

7-1018-C7-1027-C 7-1048-F

7-1418


R10

1 YEAR WARRANTY

7-1426-C

7-1118-S

General purpose LED worklights

Order code Shape/Type Dimensions (mm) excl mount bracket Watts Beam Beam angle

(degrees) Lumens

7-1426-C Rectangular 139W x 45H x 72D 15W Combination 20/40 10507-1118-F Square 76W x 83H x 42D 18W Flood 60 14007-1118-S Square 76W x 83H x 42D 18W Concentrated 30 14007-1020-BS Round 98W x 63H x 75D 20W Spot blue 5 14007-1020-S Round 98W x 63H x 75D 20W Concentrated 30 1600

7-1127-F Rectangular - with integral on/off switch

150W x 167H x 57D 27W Flood 60 21607-1127-FM With magnetic mount and coil lead/plug

7-1127-C With switched coil lead/plug

7-0000-CW Magnetic mount option with coil lead and switched plug for work lights

• Rugged and weatherproof• Latest LED technology• Long life and low current drain• Typical working life of 30,000 hours

For general applications, the 7-1426’s specially designed combination optic beam offers an excellent combination of range and beam spread.At just 76mm wide, the 7-1118-S projects a very powerful 1400 Lumen spot for its compact size.The 7-1020 is available as a conventional white light version and as a separate model (7-1020-BS) featuring blue LEDs which, with its special purpose optic, projects a concentrated circle of blue light downwards. The 7-1020-BS is intended to warn pedestrians of an approaching fork lift truck or similar vehicle.

There are further worklights in the range, including wireless remote control motorised searchlights which provide very precise illumination of a scene. In addition, for applications requiring even larger amounts of light, Haztec’s linear bar lights offer outputs from 3,400 up to a very powerful 25,500 Lumens. Lights can be angled up or down for better illumination of the working area and are sealed to IP67 so are sufficiently robust for harsh environments.

7-1020

7-1127 with swivel mount and handle

167mm


R10

1 YEAR WARRANTY


R107-1160/1190 60 & 90W high power worklights

• Very powerful, heavy duty light using multiple 10W Cree LEDs • 5400 (7-1160) and 8100 (7-1190) Lumen output• Choice of long range spot or wide angle flood beam• IP67 rated - suitable for harsh environments

• Choice of wide angle 90 degree flood beam or long range 10 degree spot beam versions

• Rugged construction with cast aluminium body and polycarbonate lens

• Front lens secured with Allen screws and gasketed for enhanced ingress protection

• Extensive heatsinking fins maintain stable LED temperature to maximise performance and LED life

Mounting options:• Surface mount using heavy duty bracket

Voltage:• 9-32VDC suitable for 12/24V operation

Dimensions (mm) 135L x 124D x 150H (without bracket)Order code Description Lumens7-1160-F 60W LED flood light (90 degree beam) 5,4007-1160-S 60W LED spot light (10 degree beam) 5,4007-1190-F 90W LED flood light (90 degree beam) 8,1007-1190-S 90W LED Spot light (10 degree beam) 8,100

7-1160-F 7-1190-F

7-1160-S 7-1190-S

2 YEAR WARRANTY

7-7250 self-parking high power LED searchlight

• Powerful 50W LED searchlight with 3045 Lumen output• Wired or wireless control• Self-parking for safe use • Long range beam• CANbus control interface option• Fully weatherproof design• 3600 rotation

Beam spread:• Peak light output generated across a 10 degree horizontal and vertical

spread, providing an excellent long range beam• Significant light output also provided over a 30 degree spread giving wide,

uniform short range coverage

Operation:• Unlimited 360 degree horizontal rotation, 90 degree upward vertical

elevation and 30 degree downward elevation• Fast and slow movement speed also available (controller dependent)• When switched off, light automatically self-parks in the home position for

both tilt and rotation, ensuring a safe position that will not dazzle other vehicles when next switched on. This function also allows the operator to know exactly where the aim point of the light will be when switched on even if they do not have direct sight of the searchlight

Options:• Handheld wireless remote control included as standard. Optional dash

mount remote available - please see TL and TLED series searchlights for options

• Optional interface for operation by a Haztec CANbus controller such as the 8-82306 or 8-82312

Voltage:• Suitable for 12 or 24V operation

Dimensions (mm) 120H x 212W x 280D 50W Self-parking motorised LED searchlightOrder code DescriptionNEW 7-7250 Self-parking 50W motorised LED searchlight (12/24V)

8-82858 8 output CANbus switch module allowing searchlight to be controlled using Haztec CANbus multi-purpose handsets

8-82306 6 button CANbus switch with coiled lead and magnetic mount holder8-82312 12 button CANbus switch with coiled lead and magnetic mount holder

7-7250

70 Metres10 250190

32 Lux 16 Lux 8 Lux 4 Lux 2 Lux 1 Lux

30

-30

0Beam angle

NEW


R10

2 YEAR WARRANTY


R10TL series motorised searchlights

• Low profile powerful searchlight with wireless remote control • Full 360 degree rotation and 90 degree elevation• Long range 8 degree uniform spot beam• Halogen or LED variants• Up to 2400 Lumen output - see table below

Wireless operation:• Wireless remote control of on/off, rotate and elevate

functions• 433.92Mhz operation - typical range up to 65 metres in

free air• Supplied with one remote control - extra units can be

ordered separately - please see table below• Up to four controllers can be programmed to work with

one light

Mounting options:• Permanent mount using four fixing bolts. The light head

can be removed from the base for maintenance• 7-1007 can be supplied as magnetic mount with a flying

lead and cigar plug

Halogen handheld wireless remote control searchlight - permanent mount Dimensions (mm) 190L x 155W x 130H Weight 1.2kgOrder code Description Output (Lumens)7-1007-x 12V 55W H3 Halogen searchlight with 7-SL010 handheld battery powered wireless remote 10007-1007-x-24 24V 70W H3 Halogen searchlight with 7-SL010 handheld battery powered wireless remoteLED wireless remote control searchlight with purpose-designed optical reflectorDimensions (mm) 190L x 155W x 130H Weight 1.4kg7-1150-x 12V 30W LED searchlight with 7-SL007 deluxe handheld battery powered wireless remote 12007-1150-x-24 24V 30W LED searchlight with 7-SL007 deluxe handheld battery powered wireless remoteLED wireless remote control searchlight Dimensions (mm) 149L x 181W x 169H Weight 1.9kg7-1220-x 12V 50W LED searchlight with 7-SL007 deluxe handheld battery powered wireless remote

24007-1220-x-24 24V 50W LED searchlight with 7-SL007 deluxe handheld battery powered wireless remote7-1222-x 7-1220 12V 50W LED searchlight with 7-1027 dash mount 2 speed wireless remote7-1222-x-24 7-1220 24V 50W LED searchlight with 7-1027 dash mount 2 speed wireless remoteOptions and additional/spare remote controls for all TL, TLED and 7-7250 search lights - work in addition to handheld controller supplied as standard with each light -M Magnetic mount option for 7-1007 & 7-1150 - heavy duty magnet, flying lead and cigar plug7-SL007 Deluxe handheld battery powered wireless remote control 7-SL009 Dash mount battery powered wireless remote control7-SL010 Handheld battery powered wireless remote control

7-1027-12/24 Hard wired dash mount two-speed remote control with wireless communication to searchlight, 12 or 24V supply - please specify on order

Black or white housings available - please specify preferred colour when ordering

7-1027 dash mount hard wired wireless remote control

7-SL010 handheld wireless remote control

7-SL007 deluxe handheld wireless remote control

7-1007-B 7-1150-B 7-1220-W

1 YEAR WARRANTY

7-SL009 dash mount wireless remote control


R10 4-1547 compact LED scene lights

• Powerful 10W LED scene light with 400 Lumen output• Choice of flood or spot beam• Integral heatsinking for a typical working life of 50,000 hours

Mounting options:• Surface-mount unit complete with cast surface bezel in

black or white • Single hole mount - 20mm mounting hole also acts as

the cable entry facility• Optional L bracket• Optional angled rubber mount - allows surface mount

versions to be angled down or compensates for angled mounting surfaces

Voltage:• 10-40VDC supply suitable for 12 or 24V operation

Order code Description Dimensions (mm)Single hole mount4-1547-F Flood light single hole mount, black bezel 50L x 40H x 24D1 + 16D24-1547-S Spot light single hole mount, black bezel 50L x 40H x 24D1 + 16D2Surface mount4-1547-S-F Flood light surface mount, black bezel 85L x 55H x 37D4-1547-SW-F Flood light surface mount, white bezel 85L x 55H x 37D4-1547-S-S Spot light surface mount, black bezel 85L x 55H x 37D 4-1547-SW-S Spot light surface mount, white bezel 85L x 55H x 37DOptions4-1005 L bracket for 4-1547 (black) 45L x 56H x 31D4-10500 20 degree angled rubber mount for 4-1547 90L x 59H x 22D (max)

4-1547-S on 4-10500 angled rubber mount

4-1547-S-F surface mount (flood beam optic)

4-1547-S mounted on optional 4-1005 L bracket

4-1547- S single hole mount (spot beam optic)

5 YEAR WARRANTY

4-10412 12LED scene light

• 12 x 1W high output LEDs with low current draw• Working life of over 50,000 hours • Purpose-designed optical design directs light downward • Optional rubber mount increases downward beam angle to 45 degrees• Strong UV stabilised polycarbonate lens and bezel

• Powerful 800 Lumen output with purpose-designed optical system for very precise direction of light, minimising glare and stray light

• Light is concentrated from 0 to 30 degrees below horizontal, with peak output 15 degrees below horizontal. Beam width is 20 degrees either side of vertical

• Optional mount provides an additional a downward angle of 30 degrees, giving a total of 45 degrees beam angle - ideal for high mounting heights or where there is a need to focus light near to the vehicle

IP rating:• Sealed to IP65 and designed to withstand vibration from

heavy duty commercial vehicle applications

Mounting:• Two hole surface mount with rubber seal - no need to

cut recesses in vehicle bodywork

Materials:• Strong UV stabilised polycarbonate lens and bezel• Robust cast metal mounting bezel with ample heat

dissipation to ensure long LED life

Voltage:• 10-40V supply, suitable for 12V or 24V operation• Low current draw, typically 0.75A at 13.8V • Power regulated design automatically compensates for

supply voltage fluctuations

Dimensions (mm) L182 x H77 x D38Order code Description4-10412-BL 12LED scene light - black bezel, 10-40V4-10412-WH 12LED scene light - white bezel, 10-40V4-10412-YL 12LED scene light - yellow bezel, 10-40V4-10412-CH 12LED scene light - chrome bezel, 10-40VOptions4-10400 30 degree angle-down moulded rubber

mounting plinth for additional downward beam angle

0 to 30 degree angle down beam

4-10400 rubber mount increases downward

beam angle to 45 degrees

SEE PAGE

7Matching warning light available


R10

5 YEAR WARRANTY

4-1809 9LED scene light

• Purpose-designed for vertical mounting on the side of the vehicle• Powerful 1000 Lumen output with low current consumption• 0-60 degree vertical beam spread• 80 degree horizontal beam spread

• Unobtrusive design - just 30mm deep• Powerful 1000 Lumen output with a current consumption of just 12W• Special optical design provides very precise directional light - asymmetrical 60

degree vertical spread and 80 degree horizontal spread• Advanced design, cast alloy metal base with integral heatsink fins provides excellent

thermal management ensuring long LED life and high light output • Choice of bezel finish - black, white or red (RAL 3000)

Voltage:• 10-33V supply, suitable for 12V or 24V use

Dimensions (mm) L250 x D30 x H57Order code Description4-1809-BL 9LED scene light - black housing4-1809-RD 9LED scene light - red (RAL 3000) housing4-1089-WH 9LED scene light - white housing

60o Asymmetric beam

H - 57mm

L - 250mm

D - 30mm

Lateral view

60 degree asymmetric beam


R10

3 YEAR WARRANTY

• Suitable for outdoor applications such as on motorcycles*

• Momentary (press for on/release for off) or latching switching operation (press for on/press for off)

• Backlit switches with backlight connections separate to the switching contacts, allowing completely independent operation

• Simple to install with push-fit connection and push-on crimp connectors

3-1000

Cigar plug leads and weatherproof switches

• Integral fuse protection • LED indication when switch is operated• 3 metre lead length

• 3-0990/3-0995: single illuminated on/off switch with coiled or straight lead

• 3-0999: two separate on/off rocker switches, each with separate LED which indicates when activated. For ease of identification, each switch has a screen printed legend and a different colour indicator LED (1 red and 1 blue). Switches operate independently

• 3-1000: One on/off rocker switch with LED and one momentary switch for functions such as flash pattern select. The momentary output is interlocked with the

main output so is only available when the main output is on

Voltage:• Supplied with a 3 metre, 3-core lead (common negative

output plus 2 switched positive outputs)• 3-0999 and 3-1000: 12VDC supply with common 8A

rated fuse protecting both switched outputs; the fuse can be replaced by the user if required

Order code Description Fuse Rating

3-0990 Coil lead with fused and switched plug 8A3-0995 Straight lead with fused and LED indicator switch plug 10A3-0999 Straight lead with fused and 2LED indicator double switch plug 8A3-1000 Straight lead with fused and 1 on/off and 1 momentary LED indicator switched plug 8A

3-09903-0999

Order code Backlight colour Description8-61105-R Red On/off weatherproof push switch, 10A 8-61105-A Amber On/off weatherproof push switch, 10A8-61105-G Green On/off weatherproof push switch, 10A8-61106-R Red Momentary weatherproof push switch, 10A 8-61106-A Amber Momentary weatherproof push switch, 10A8-61106-G Green Momentary weatherproof push switch, 10A

1 YEAR WARRANTY12V weatherproof switches

* Please note that whilst switch fronts are fully weatherproof, wiring connections should be protected from water ingress


R10

1 YEAR WARRANTY

• 12/24V 20A rated switches• LED back-lit with additional LED ‘ON’ indicator • Choice of legends and backlight colours• Simple to install

Key features:• Designed to fit into a standard 20mm hole, switches are simple to

install with push-lock fitting and push-on connectors• Back-lit for ease of identification with separate ‘ON’ indicator

Voltage:• 12 or 24V operation, maximum load 20A

Order code Legend Backlight colour Description

8-61100-4-B-B-01 01 Blue 20A Single pole rocker switch8-61100-4-R-R-02 02 Red 20A Single pole rocker switch8-61100-4-G-G-08 08 Green 20A Single pole rocker switch8-61100-4-G-G-10 10 Green 20A Single pole rocker switch8-61100-4-A-A-12 12 Amber 20A Single pole rocker switch8-61100-4-B-B-12 12 Blue 20A Single pole rocker switch8-61100-4-R-R-19 19 Red 20A Single pole rocker switchPlease specify required backlight colour and legend when orderingOther combinations available - please contact sales

Legend 01 Legend 02 Legend 08

Legend 10 Legend 12 Legend 19

Heavy duty 12V rocker switches

6-61200 6-61220 6-62000

Multiple 6-61200 + 6-62000 linked

Order code Description

8-61200 Switch on/off large rocker: red/amber, blue, green or white light, 12V

8-61220Switch on/off/on large rocker: amber/amber, red/amber, blue/red or red/white warning (on) light, 12V

8-62000 Linking mounting panel for 8-61200 and 8-61220

• On/off or on/off/on variants • Optional 6-62000 panel for simple fixing

of individual or multiple linked switches

Illuminated on/off rocker switches

Customisable switch panels available - please contact sales for assistance

BEACON REAR 360 STOP

FLOOD SPOT

Switch panels can be customised to meet individual

specifications - please call our sales team for more

information


R10

1 YEAR WARRANTY

1 YEAR WARRANTY


R108-66000 heavy duty switching unit

• Simple surface fixing, heavy duty switch• 6 x 10A outputs• Supplied with large selection of preprinted

self-adhesive labels• Back-lit for improved visibility during use

Additional features:• External connections are by means of self-locking plug

and socket connections • Easily accessible, user replaceable 15A blade fuse per

output• Buttons illuminate red when activated, providing status

indication• Latching operation on all buttons (press for on, press for

off)

Mounting: • Supplied with fixing brackets, cables and connectors

Voltage: • Single, common heavy duty positive supply and six

separate switched positive outputs• Separate 12V auxiliary supply required to operate the

backlighting and button status indicators

Dimensions (mm) 160L X 57H x 30DOrder code Description8-66000 Dash mount switch unit - with 6 back-lit switches, LED indicators and 6 x 10A fused outputs

8-87421 motorcycle handlebar switch• Heavy duty labelled motorcycle handlebar

switch • Slide switch control of cruise, warning lights

or warning lights plus siren• Momentary air horn or siren push button• Heavy duty cable loom with weatherproof

connector included

Order code Description8-87421 Motorcycle handlebar slide switch unit with momentary push button

1 YEAR WARRANTY

1 YEAR WARRANTY


R10

8-82838-HLF

NEW

Most Haztec warning lights are supplied with integrated flash controllers offering a selection of patterns. Where a flash controller is not included, stand-alone units are available. The units below are designed for latest generation Haztec LED warning lights and offer a choice of patterns, including

simultaneous and alternating options. They are also suitable for use with other LED devices that require a 12 or 24V supply for operation. With the exception of the 6-60240, all units shown on this page are supplied with plug-in connections for ease of installation and maintenance.

LED flash control units

8-82814/8-82838/8-82800

Order code Description Outputs Supply range

LED multi-pattern flasher Up to 4 x 130mm LEDs per output 1 year warranty6-60240-12 2 output controller, 12V 2 x 1A6-60240-24 2 output controller, 24V 2 x 1ALED flasher - 3 year warranty

6-62240 18 selectable patterns, with dim and cruise modes. Runs up to 2 lights per output 2 x 5A

10-30V(Vin = Vout)6-62240-A

Airside and non-airside flash patterns plus dim and cruise modes. Flash mode is selected by a remote switch

2 x 5A

LED programmable flash controllers, 12/24V Two or more modules can be linked 2 year warranty8-82814 Compact switch module 4 x 10A*

10-30V(Vin = Vout)

8-82838 Compact switch module8 x 10A*8-82848 LINbus switch module

8-82858 CANbus switch module* Max 2 x 15A total per groupLED flash controllers Zonal switching options: cruise 25% constant illumination of corners, high/low (50%) output for night-time use plus front/rear and inner/outer switching options3 year warranty6-62400 16 selectable patterns, 12V 4 x 3A

10-30V6-62440 16 selectable patterns, 12V 8 x 3A6-62808 16 selectable patterns, 10-30V 8 x 3A

6-62812 12 selectable patterns, 10-30V - includes data lead for optional Eurosmart switching 12 x 3A 10-30V

(Vin = Vout)6-62820 12 selectable patterns, 10-30V - includes data

lead for optional Eurosmart switching 20 x 3A

Headlight flasher units

6-60930 Solid state halogen light or headlight flasher 5 selectable patterns - 1 year warranty 2 x 9.5A 10-30V

(Vin = Vout)8-82838-HLF Programmable headlight flasher

Standalone, CANbus or LINbus - 2 year warranty 2 x 10A

Run-lock unit - 2 year warranty

8-82800Run-lock control unit - plug and play operation, interlock function. Universal model for negative earth vehicles, 12 or 24V - please state when ordering

10-30V (Vin = Vout)

8-82800-CAN CANbus run-lock control unit

6-60240

6-62240

6-62400

6-62440/62808

6-609306-62820

6-62812

V11.3 03/20

DIRECTIONAL RANGE SUMMARY

Page

Appl

icati

on

Inte

gral

flas

her

Dual

col

ours

Split

col

our

Infr

ared

Sync

hron

isatio

n

Crui

se m

ode

Nig

ht d

im m

ode

Ope

ratin

g vo

ltage

R65

appr

oval

s

4-10026 12LED dual colour warning light Also available as a screen mount version - see page 15 2 Slim/screen

mount ● ● ● ● 12/24V

4-10014 4LED warning light 3 Ultra slim ● ● ● ● ● 12/24V

4-10016 6LED + 2x6LED warning light Also available as a screen mount version - see page 15 3 Ultra slim/screen

mount ● ● ● ● ● 12/24V

4-10415 4LED warning light Also available as a screen mount version - see page 14 4 Compact ● ● ● ● ● ● 12/24V

4-1548 6LED warning light 5 Compact 12/24V

4-1043 3LED warning light 6 Compact ● ● 12V

4-1044 4LED warning light 6 Compact ● ● 12V

4-1048 8LED warning light 6 Compact ● ● ● ● 12/24V

4-10409 9LED warning light 7 Wide angle ● ● ● 12/24V

4-10418 8LED warning light 8 Wide angle ● ● ● ● 12/24V

4-2033 3LED warning light 9 Economy ● ● 12/24V



4-10446 8LED warning light 10 Large format ● ● ● ● ● 12/24V

4-10479 16LED warning light 10 Large format ● ● ● ● ● 12/24V

4-1641/42/43 6 & 12LED warning lights R65 applies to 4-1641 only 11 Low profile ● ● ● 12/24V

4-1641V 6LED warning light Also available as a number plate mounted light - see page 13 12 Vertical mount ● ● ● 12/24V

4-2060 4+4LED warning light 16 Screen mount ● 4+4 12V

4-1420 hideaway warning light 18 Covert ● ● 12/24V

4-1430 hideaway warning light 19 Covert ● ● ● ● 12V

See inside for Arrowbars, LED message signs, scene, search & work lights, switches & flash control units and more

R65 Class 1

R65 Class 1

R65 Class 2

R65 Class 1

R65 Class 1

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 1

R65 Class 1

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 2

R65 Class 1

R65 Class 2

R65 Class 1

R65 Class 1

R65 Class 2

R65 Class 2

R65 Class 2

Haztec International LtdMoorfield Road ∙ Leeds ∙ LS19 7BN ∙ England

T: +44 (0)113 202 9115 ∙ [email protected] ∙ www.haztec.uk

WARNING LIGHTS, ARROWBARS, Brochure …...3 T: +44 (0)113 202 9115 infohaztec.uk T: +44 (0)113 202...

Documents

Transcript of WARNING LIGHTS, ARROWBARS, Brochure …...3 T: +44 (0)113 202 9115 infohaztec.uk T: +44 (0)113 202...