Volvo Navigations system Installation.pdf

8/14/2019 Volvo Navigations system Installation.pdf

1/24

Installation instructions, accessories - Navigation system portableVolvo Car Corporation Gteborg, Sweden

XC60Section Group Weight(Kg/Pounds) Year Mont

3 391 0.067 / 0.15 2009 08

XC60 2009, XC60 2010

IMG-334408


2/24

Required tools:

A0000162 IMG-239664

IMG-334484

IMG-334409


3/24

IMG-334410


4/24

INTRODUCTION

NOTE! Read through the whole installationinstruction before starting the work.

The front page gives the date of this edition andthe edition it replaces

The second page shows the tools needed for theinstallation and the contents of the installation kit

The illustrations display the procedure in order ofoperation. The order of operation is repeated inthe text section

Cut out the text page in order to follow theillustrations and text at the same time.

Navigation system portable


5/24

1

IMG-245980

Note!

Work is carried out the same way on left-hand drive cars as onright-hand drive cars (Mirrored). Left-hand drive car shown. In caseswhere there are differences between left and right-hand drive cars,both versions are shown.

Turn the ignition switch to position 0.

Note!

Wait at least three minutes before unplugging the connectors orremoving other electrical equipment.

2

IMG-298585

Remove the tunnel console's panel on the left-hand side (Alsoapplies to right-hand drive cars). It is secured with sevenclips on the inside.

3

IMG-282523

Carefully pry loose the panel with air blower all round. Thepanel is secured by five clips on the sides and at the top andwith four mounting springs on the lower edge.

4

IMG-282524

Pull out the panel and disconnect the connector for the hazardwarning lights.

5AIllustrations A and B

Replacement of the panel for the air vent

Poke the catches downwards using a small screwdriver.


6/24

IMG-303983

5B

IMG-303984

Fold down the air nozzle and unhook it from the four mountingeyelets at the lower edge of the panel.

6

IMG-303985

Poke the catches on the hazard warning button in and pushthe button out.

7

IMG-334413

Remove and transfer the clips to the new panel, place the oldone to one side.

8

IMG-334414

Install the button for the hazard warning lights in the newpanel.


7/24

9

IMG-334416

Install the air vent in the new panel.

10

IMG-329154

11

IMG-329155

Use tape to protect the tunnel console.

12

IMG-293021


8/24

13

IMG-293022

14

IMG-293023

15

IMG-293024

16

IMG-329163

17


9/24

IMG-293028

18

IMG-293029

19

IMG-329164

20

IMG-334421

Remove the rear end with cover.

Disconnect the connectors for the 12 V socket and seat

heating.

21

Route the cable harness to the centre console in the sameway on left-hand drive and right-hand drive cars


10/24

IMG-334422

Take a piece of curtain wire and insert it in the rear edge of thetunnel console and slide it forward on the left-hand side andout where the left side panel was located.

Lift up the console at the rear edge to facilitate access.

22

IMG-334423

Take the large cable harness from the kit and secure it to theend of the wire using a piece of masking tape.

Pull the cable harness forward.

Lift up the tunnel console at the rear edge to facilitate pullingthrough.

Check that the cable harness is not trapped when the tunnelconsole is positioned.

23

IMG-334424

Connect the male connector (1) in the new cable harness tothe 12 V socket.

Connect the disconnected connector (2) from the 12 V socketto the female connector (2) in the new cable harness.

Reconnect the green connector (3).

Insert the connectors and fuse holder down as far as possible.

24

IMG-329164

25

Wrap the connectors and fuse holder with foam tape.


11/24

IMG-334425

26

IMG-334426

Position the connectors and fuse holder.

27

IMG-334427

28


12/24

IMG-334428

29

IMG-334429

30

IMG-293023

31

IMG-334431

32


13/24

IMG-334432

33

IMG-334433

Insert the wire through the centre console on the left-hand sideand out where the side panel was located.

34

IMG-334434

Tape the routed cable using a piece of masking tape and pullup.

35

IMG-334435

Take the short cable from the kit and connect to the newlyrouted one.

36 Steps 36-49 are mirrored for right-hand drive cars


14/24


15/24

40

IMG-222268

Remove the screws and the panel.

41

IMG-222270

Disconnect the lighting connector and place the panel to oneside.

42

IMG-295944

Remove the two screws.


16/24

43

IMG-295945

Carefully pry off the glovebox lighting.

44

IMG-295946

Loosen the connector from the lamp in the glovebox lighting, itmay be tight.

45

IMG-295947

Remove the six screws.

If necessary, disconnect the connector from the SIM cardholder.

Pull the glove compartment out slightly so that the clipsrelease.

Remove the glovebox.

46

Take the panel with cradle and aerial from the kit.


17/24

IMG-334449

Insert the aerial over the air vent to the right and down towardsthe rear edge of the dashboard.

Note!

Leave enough cable excess so that the panel with cradle is not inthe way when making connections in the centre console.

47

IMG-333785

Continue to route the aerial with cable, from the right air duct inthe centre console, and then along the rear edge of thedashboard to the right.

Secure using pieces of butyl tape.

48

IMG-333786

Continue to route the aerial with cable towards the air duct atthe right end of the dashboard.

Route it on the outside of the air duct and out through the holein the end and position on the dashboard.

Secure the cable to the outside of the air duct using butyl tape.

49

Clean the surface in front of the air vent on the right-hand sideof the dashboard and wipe dry.


18/24

IMG-334451

50

IMG-334452

Remove the protective tape from the mounting tape.

51

IMG-334453

Steps 51-53 are mirrored for right-hand drive cars

Secure the aerial approximately in position as shown.

52

IMG-334454

Route the cable under the cradle (1) for the A-pillar and back.

Route the cable excess back to the rear edge of the dashboardwhere the cable was previously routed.

53AIllustrations A and B

Secure the cable excess at the existing pieces of butyl tapeaccording to image A and B.

Also secure on the right-hand side of the air duct.


19/24

IMG-334455

53B

IMG-334456

54

IMG-334457

Secure the green connectors at the existing cable harnessusing cable ties.

55

IMG-334458

Connect the connectors to the cradle and button for the hazardwarning lights.

56

Push the panel into place. Ensure that the cables are not infront of the air vents.


20/24

IMG-334459

57

IMG-333791

Steps 57-66 are mirrored for right-hand drive cars

58

IMG-333792

59

IMG-333793

60


21/24

IMG-296464

Take the glovebox and connect the connector to the Sim cardholder, if necessary.

Insert the connector to the glovebox lighting.

61

IMG-296465

62

IMG-296466

63

IMG-296467

64


22/24

IMG-286608

65

IMG-225272

66

IMG-280033

67A

IMG-333800

67B

Illustrations A, B and C

Take the Garmin device, connect the aerial and align the guideholes in the bottom, with the corresponding lugs in the cradle.

Fold it to the limit position and check that it springs up andlocks in the catches on the reverse. When removing, press thereceiver down until the catches release and then fold itbackwards and disconnect the connector from the aerial.


23/24

IMG-333801

67C

IMG-334328


24/24

VolvoCar Corporation, 2009 Printed in Sweden 3075814

Volvo Navigations system Installation.pdf

Documents

Transcript of Volvo Navigations system Installation.pdf