Vinyl Fence and Railing - Roofing Hardware and Supply Company … · 2017-04-05 · If you can’t...
Transcript of Vinyl Fence and Railing - Roofing Hardware and Supply Company … · 2017-04-05 · If you can’t...
Vinyl Fence and Railing
Virtually maintenance free
Weather resistant
Safe, strong, durable, and ideal for all climates
No painting, sanding, or maintenance required
Easy to clean
Will not corrode, flake or discolor
Protection from discoloration due to ultra violet rays
Easy to install
No insect damage
Consistently meets and exceeds quality and appearance
Limited lifetime warranty
Resistant and self-extinguishes to fire
Maintains beauty year after year
The vinyl fence that we supply has been through
performance testing for impact, weather, and resistance
to discoloration. The profiles are safe, strong, flexible,
durable, and will hold up to any climate. Properly
assembled fence will withstand snow loads and high
winds, and can used to protect children or pets from
WHY PRO ELITE & PRO GUARD VINYL?
HOW VINYL FENCE IS MANUFACTURED
PROFILES:
Vinyl fencing originates as a PVC powder-form resin. When
blended with the required additives, the formulation is fed
into an extruder where it is formed into a malleable vinyl.
The vinyl is then fed through a die into the shape of the
finished profile. While using vacuum technology to retain
the malleable vinyl’s proper shape, water is introduced to
cool the vinyl to its desired and final rigid state.
PERFORMANCE:
Vinyl fences are engineered to retain their beauty and good
looks throughout their lifetime. We do not recommend
painting your vinyl fence. Painting or otherwise treating the
vinyl products will void the limited lifetime warranty.
Vinyl will not mildew. Mildew feeds off organic materials.
PVC in non-organic and therefore does not support mildew.
The high-gloss, smooth, non-porous surface, makes it
difficult for organic material to attach (e.g., dirt) and
therefore does not promote the growth of mildew. The use
of non-chalking TiO2 (titanium dioxide) further prevents
most mildew.
Vinyl is formulated to be non-toxic to the environment. It
will not
Power auger or post hole digger
Shovel, and digging bar (optional)
Bright colored spray paint
String line stakes and level
Cordless or power drill with drill and screw bits
Tape measure, safety glasses and work gloves
Miter saw or circular saw to cut rails (if applicable)
Table saw or circular saw to cut pickets
Set all corner, end, and gate posts first for proper
alignment. This also allows you to get the height on
all posts accurate by running a string line from
beginning post top to ending post top.
WE RECOMMEND YOU HAVE A PROFESSIONAL INSTALLER TAKE
CARE OF YOUR FENCE. WILL GIVE YOU THE NAMES OF SOME OF THE
BEST INSTALLERS IN TOWN.
HELPFUL HINTS
DO IT YOURSELF, THIS IS WHAT YOU
NEED
FOLLOW THESE IMPORTANT STEPS
Locate property lines. You can find these by locating
a pin placed in the curb in the front of your house or
by a stake buried in the ground or by the post placed
in the back. If you can’t find any of these then try
and locate a plot map from your city. Otherwise you
will have to hire a surveyor to locate your property
lines.
Check your local city regarding fence locations in the
front of the house. Some cities may restrict you at 3’
or 4’ height limit. Also check for overall fence
heights in your city. A permit may be required for
fences that exceed 6’ in height.
If you live in and HOA make sure to have your fence
color and height approved before installing. This will
save you money and possible delays.
CONTACT BLUE STAKES FOR LOCATION OF
PRIVACY PANEL -
2 RAILS 2 POSTS 2 CAPS 2 U-CHANNEL 6 TONGUE & GROOVE SLATS 2 3/4” SCREWS FOR UCHANNEL
PREPARE FENCE LAYOUT
Please read these instruction sheets completely before
beginning work. Laying out the fence is an important
first step toward a quality installation.
STEP 1:
LOCATE YOUR
PROPERTY LINES
STEP 2:
DRIVE STAKES INTO THE
GROUND JUST BEYOND
WHERE THE POSTS ARE
BEING PLACED AND OFF
CENTER OF THE PROPERTY
LINE. STRETCH A STRING
FROM STAKE TO STAKE.
STEP 3:
MARK THE LOCATION OF
EACH POST HOLE. LOCA-
TIONS SHOULD BE 73” ON
CENTER FOR 6’ SECTIONS
TIP: USE SPRAY PAINT TO
MARK HOLE LOCATIONS.
EXAMPLE:
SETTING THE POSTS
STEP 1:
Dig holes approximately 8” - 10” in diameter and 24”
deep.
STEP 2:
Place the post in the center of the hole and square it up
with the fence line. Check the post on two adjacent sides
with a level or use a post level to check for plumb. You
will adjust for the height of the fence at this time. It is
recommended that you set the post 2” from the bottom
of the bottom rail to the ground.
STEP 3:
Pour concrete around posts and fill up to 24” below
ground level. If using mixed concrete make sure it is
only slightly wet. This will allow for a faster set-up and
less chance of leaning due to the wind. If using dry con-
crete, dump 1/3 of the bag in the hole and mix with
some water. Repeat this step until filled. Follow these
steps until all posts are set
and are ready for panel in-
stallation. Relevel posts if
necessary before concrete is
set.
PANEL ASSEMBLY - BOTTOM RAIL
STEP 1: Slide bottom rail into the post and secure bot-
tom rail with a screw. If you have to cut your rail, make
sure that your rail is 3” longer than your post to post
measurement. This will allow for proper inset.
PANEL ASSEMBLY - TOP RAIL
STEP 2: Follow the previous instructions. Secure the
rail then move onto next step.
PANEL ASSEMBLY - PANELS
STEP 3: Starting at the end, insert the panels into the top
and bottom rails and move down the rail.
PANEL ASSEMBLY—U-CHANNEL
STEP 4: (If applicable) Put U-channel on the posts be-
tween the holes for the top and bottom rail. You can use
a grabber screw about 3/4” to 1” length to secure the U-
channel.
NOTE: ALTHOUGH OPTIONAL, U-CHANNEL IS
RECOMMENDED FOR TAN OR ADOBE COLORED VINYL
AND IN SOME CASES IT’S REQUIRED FOR FULL
**IF YOUR RAILS DON’T COME PRE-NOTCHED, YOU
CAN RENT A NOTCHER OR SECURE WITH SCREWS TO
ATTACH THE RAIL.
POST CAPS
Apply a small amount of PVC glue to the inner rim of
the cap and place onto post. Make sure the cap is firmly
in place.
TIP: PLACE ONLY ONE OR TWO DOTS OF GLUE.
THIS IS SUFFICIENT FOR HOLDING THE CAP
CLEANING
During installation your fence will collect some vinyl
residue and dirt due to static electricity and basic instal-
lation procedures. In most cases you can spray this off
with a hose. However, for more stubborn marks you can
use some simple green cleaner with non-abrasive scotch
brite pad. This is also the best thing to use to clean and
SECURING RAILS WITH SCREWS
STEP 1: To secure bottom rail, screw a screw into the
wall of the rail at an angle towards the inside of the post.
This will securely hold the rail in place and will make
removal easier if necessary.
STEP 2: To secure the top rail, screw a screw into the
top rail next to the post at an angle. This will securely
hold the rail in place and will make removal easier if
necessary. (secure screws should be hidden inside rail
ACCESSORY COLORS AVAILABLE
CAPS
SPECIALTY CAPS/LIGHTED CAPS
** CAPS ALSO AVAILABLE IN DIFFERENT STYLES AND COLORS**
FINISH COLORS AVAILABLE
Pyramid Cap Gothic Cap Ball Cap
Internal Pyramid Cap Dog Ear Picket Cap Nantucket cap
Stallion Cap Lighted Cap Solar Cap
PRIVACY FENCE
6’ Privacy Pocket Rail Privacy
Jail Box Two Tone
Step Fence 4’ - 3’
6’ Privacy Fence Mocha Walnut 6’ Privacy
6’ Privacy
RANCH RAIL
2 RAIL
RANCH 3 RAIL
RANCH
4 RAIL
RANCH
3 Rail Ranch Fence
2 Rail
Ranch Fence
2 Rail
Ranch Fence
OPEN PICKET/CLOSED PICKET
Closed Picket Fence
Scalloped Picket Fence
Closed Picket Pool Fence
PORCH RAIL/ADA RAIL
PERGOLA / AWNINGS /
Stair Rail and Post Kits Fast, Easy, and Affordable
Residential Rail Kit
Parts
6' Straight Rail Kit White
Part Number: PE6W White 6' Straight Rail Kit
PE6T Tan
Box Set Includes: 2 - 2x3.5x72 Rail White
13 - 7/8x1.5" Picket White
4 - 2x3.5" Mounting Brackets
8' Straight Rail Kit White
Part Number: PE8W White 8' Straight Rail Kit
PE8T Tan
Box Set Includes: 1 - 2x3.5x16' Rail White
18 - 7/8x1.5" Picket White
4 - 2x3.5" Mounting Brackets
1 - 96" Rail Stiffener
6' Stair Rail Kit White
Part Number: PE6SW White 6' Stair Rail Kit
PE6ST Tan
Box Set Includes: 2 - 2x3.5x72" Rail White
11 - 7/8x1.5" Picket White
4 - 2x3.5" Mounting Brackets
8' Stair Rail Kit White
Part Number: PE8SW White 8' Stair Rail Kit
PE8ST Tan
1 - 2x3.5x16' Rail White
15 7/8x1.5 Picket White
4 - 2x3.5 Mounting Bracket
1 - 96" Rail Stiffener
4x4x38" Post Kit White
Part Number: PE39W White Post Kit
PE39T Tan
Box Set Includes: 1 - 4x4x38 Post White
1 - 4" Cap White
1 - 4" Trim Ring White
4x4x44" Post Kit White
Part Number: PE44W White Post Kit
PE44T Tan
Box Set Includes: 1 - 4x4x44 Post White
1 - 4" Cap White
1 - 4" Trim Ring White
**Please contact the Pro Sales Department for other options.