VIEW ON THE CONTROL ASPECTS OF UNIVERSAL MOTOR SUBRAMANIAN.R Edited By Sarath S Nair 1.
-
Upload
axel-ryall -
Category
Documents
-
view
216 -
download
0
Transcript of VIEW ON THE CONTROL ASPECTS OF UNIVERSAL MOTOR SUBRAMANIAN.R Edited By Sarath S Nair 1.
VIEW ON THE CONTROL ASPECTS OF UNIVERSAL MOTOR
SUBRAMANIAN.REdited By
Sarath S Nair
www.technologyfuturae.com1www.technologyfutuare.com
SYNOPSISBasics of universal motor
Characteristics
Control aspects
Equivalent circuit
Analysis
Conclusion
References
2www.technologyfutuare.com
UNIVERSAL MOTOR
Can run on either dc or ac power
A series wound dc motor
A double-excited motor
High starting torque and a variable speed
characteristics
Runs at dangerously high speed on no load
Input range is few watts to 2000 watts3www.technologyfutuare.com
PARTSStator: field windings to generate the radial
magnetic flux
Rotor: armature winding supplied with
current through the carbon brushes to generate
magnetic flux
Brushes: mechanical linking of power supply
and rotor windings
Commutator & a compensating winding4www.technologyfutuare.com
UNIVERSAL MOTOR FROM A BLENDER
Fig.1 Fig.2
5www.technologyfutuare.com
CONSTRUCTION
Permanent magnets in dc motor is replaced
by electromagnets
manufactured in two types
1. Concentrated-pole, non-compensated
2. Distributed-field compensated
6www.technologyfutuare.com
Contd…
Concentrated-pole, non-compensated
low rating
Stator: Two salient poles & like a two pole dc
series motor except that whole of its magnetic
path is laminated
Rotor: wound type and a small dc motor with
laminated core having straight slots having
armature winding is connected to the commutator7www.technologyfutuare.com
Contd…
Distributed-field compensated
high rating
Stator: Similar to that of a split phase motor
Rotor: Wound type similar to that of a small d.c. motor
Compensating winding is used to reduce the reactance
voltage present in the armature when motor runs on ac
supply
The reactance of the field winding can be kept low by
limiting the number of turns.8www.technologyfutuare.com
OPERATION
With input DC power, the stator coils as permanent magnets
like a DC motor & continues to rotate in the same direction
the current through the rotor also reverses the current through
the electromagnets
every pole of the motor changes from north to south or from
south to north 9www.technologyfutuare.com
Contd… With input AC power, it reverses the poles and thus the
direction of rotation is obtained.
experiences no torque during current reversal, but the
average torque is sufficient to turn the motor as if it were
connected to a DC power supply.
different rotational speeds can be achieved by varying
the amount of current reaching the electromagnets.
The starting torque of a universal motor is determined by
the current that flows through the armature 10www.technologyfutuare.com
ADVANTAGES
Simple structure
Robust
Small size & compact
Portable
Good power density characteristics
Rotates more than 3000 to 25000 rpm
11www.technologyfutuare.com
DISADVANTAGES Sparks occurring between brushes & commutator due to their
imperfect electrical contact leads to loud noise while operating
As a result life of brushes is reduced
High maintenance requirements
High peak to peak current gains poor motor efficiency
High brush temperature results in limited motor lifetime
APPLICATIONS Speed control and high torque are required
Typical applications are in the field of power tools and home
appliances like mixers, washing machine.12www.technologyfutuare.com
CHARACTERISTICS
13www.technologyfutuare.com
Contd…
Torque is inversely proportional to speed & directly
proportional to the current
More current flows at high speed, torque increases
as magnetic flux density also increase
low speed tends to cause magnetic saturation,
deteriorates the characteristic of the motor
Rotation speed is determined by the no. of
windings
14www.technologyfutuare.com
CONTROL ASPECTS
In domestic appliances, Electric motors the ability
to control its speed
Two control methods
1. Phase angle control
2. Chopper control
15www.technologyfutuare.com
PHASE ANGLE CONTROL
16www.technologyfutuare.com
Contd… Phase angle control is a simple and cost-effective
solution
The speed of a universal motor is controlled by
using a triac.
The gate of the triac can be controlled directly by
the output ports of a microcontroller
The whole circuitry is usually connected directly to
the mains.17www.technologyfutuare.com
Contd…
Advantages
1. simplicity
2. cost effectiveness
3. full speed control
Disadvantages
4. high brush noise
5. short lifetime
6. high current ripple 18www.technologyfutuare.com
CHOPPER CONTROL
PWM control
The AC voltage from the mains is rectified and then
switched at a high frequency by a Power MOSFET
or an IGBT
lower current ripple which reduces the harmonics
reduces the copper and iron losses
19www.technologyfutuare.com
Contd…Advantages
1. Higher motor efficiency
2. Lower acoustic noise
3. Smooth current behavior
Disadvantages
1. More components needed
2. Filtering of chopper frequency required
Two chopper control method is used
1. DC chopper speed control
2. DC chopper speed and current control20www.technologyfutuare.com
1. DC CHOPPER SPEED CONTROL
The speed regulation is poor at low and medium speeds
The average error is large
The speed regulation improves at high speeds
The speed dynamic response is slow
Control system takes a long time to get back to a steady state when
load changes21www.technologyfutuare.com
2. DC CHOPPER SPEED AND CURRENT CONTROL
The current control loop is designed to be much
faster than the speed control
a fast dynamic response to load changes22www.technologyfutuare.com
EQUIVALENT CIRCUIT
The equivalent circuit of a proposed universal
motor with speed and current control is shown in
Figure
23www.technologyfutuare.com
Contd… The model of the proposed universal motor control can be
described mathematically as:
e the motor back emf
k1 is the motor constant dependent on the motor
characteristics.24www.technologyfutuare.com
Contd… V(t) = [R + Lp – k1w]i(t)
Where
R=Ra+Rf
Lp =La+Lf
The mechanical equation can be written as
a serial excitation motor
the motor torque is proportional to the square of the motor
current25www.technologyfutuare.com
MODEL OF UNIVERSAL MOTOR Dynamics of universal motor is governed by the equations:
Term ωφ in (1) represents the Counter electromotive force
Term iφ in (2) is the electromagnetic Torque produced by the motor.
The flux φ is a function of the current I, a non-linear system of
equations.
The relation between Φ and I is
Φ(i ) =k(| I |)I (3)
Where the coefficient k is the mutual inductance Between the field and
armature coils.26www.technologyfutuare.com
CONCLUSION
The basic outline of the universal motor & the dc
chopper speed & current control are discussed here
Equivalent circuit & model of the universal motor
are also explained briefly
27www.technologyfutuare.com
Log On to www.technologyfuturae.com
Technology Futurae
Technical Presentations, Research Reviews, New designs & Developments
REFERENCES[1] Huangsheng Xu, Kevin King, and Yashvant Jani Renesas Technology America, Inc. 450
Holger Way, San Jose, CA 95134 “ High Performance DC Chopper Speed and Current Control
of Universal Motors Using a Microcontroller” 0197-2618/07/$25.00 © 2007 IEEE
[2] Hac1 Bodur, A. Faruk Bakan, M. Hadi Sarul Yildiz Technical University, Dept. of Electrical
Engineering Istanbul 80750, TURKEY “Universal Motor Speed Control with Current
Controlled PWM AC Chopper by using a Microcontroller 0-7803-5812-0/00/$10.00~2000IE
[3] L. C. PACKER Associate. A. I. E. E. “Universal Type Motors” Westinghouse Electric &
Mfg. Co., Springfieldl Mass.- Presented at the Regional Meeti,ng of the A. I. E. E., Swarmp-
scott, Mass., May 7-9, 1925
[4] Rex Miller and Mark Richard Miller “Small Electric Motors” 2nd Edition Wiley-dreamtech
India Pvt. Ltd
[5] Charles I. Hubert “Electrical Machines” 2nd Edition Pearson Education
[6] B.L.Theraja, A.K. Theraja “ A Textbook of Electrical Technology” Volume II AC &DC
Machines S.Chand & Company Ltd. 29www.technologyfutuare.com