Be carelul not to touch with metals/conduClives.

AL'NCO

PS0261Printed in Japan

• SPECIRCATlONS:

<General>• Frequency range/144.000-145.995MHz(E), 144.000-147.995MHz(T). ModuIation/F3E· DC ~rsource/3.6-4.5V~ntemaJ

batt8/Y), 5.5V (external regulated source) • Current TX/ approx.260mA @4.5VDC, RX/approx.33mA (squelched). Dimensions/55(W) x 100(H) x 28(D)rrm without projections • Weightl approx.185g (With three AA drycells)

<Tnlnamltter>• Output Power/ approx. 340mW @4.5VDC • Modulator/Variablereactance e Max. deviation / ± 5kHz

<Receiver>Configuration/Double conversion superheterodyne .'.F./1st:23.05MHz/2nd: 450kHz· Sensitivity/betterthan -15dBI' (12dBSINAD). AF output/not less than 1CJOmW (10% distort. @80)

ALINCO, INC.Head Office: "'TWIN 21" MID Tower Building 23F

1-61. 2-ehome. Shlroml, Chuo-kU. Osaka 540. JapanPhone: 08-~1150 Fax: 06-946-8175 Telex: 8308t5E-mail: 101243.1446@compuserve.com

VHF FM MINI POWER TRANSCEIVER

DJ-S11Telescopic AntennaI------+­

Rotate. stand up and extend fully when operating.

Function (F) 1Press and hold this key and press another key toactivate the secondary function. Press andrelease this key quickly to change the blinkingfrequency dtgit: the blinking digit can be changedwith the UP/DOWN keys.

MONITOR 1Press this switch to unmute the preset squelchand monitor weak signats. Press and hold theF-key and press this key to lock/unlock the keys toavoid unintended key entries. ("L" is displayedduring the keylock.)

ExtemIII PO_ Tennlnall------+-+-----...00 not connect any power supply when dry ceUeare Installed in the radio.It NiCd baneries are inataned. charging can bedone through this terminal using the EOH-18.EOC·78179 charger, Of an external regulated5.5V DC (negatiVe ground).(Do not u" any other types of charger orals. theradio will be damaged and warranty will be void.)

PTTIPress-tcHalk switch.

•

Extemel Speeker JlIc:k 1Connect to this jack when using an optionalspeaker (e.g. EMS·9. EME·12. e1C.)

External Microphone JlIc:k 1COnnttCt to this Jack when using an optionalmicrophone (e.g. EMS-9. EME-12, .'c.)

• FEATURES

® "N" ;, displayed continuously on aprogrammed memory channel. The "M""ashes on a memory channel not yetprogrammed.

® Memory channel number.

© Frequency(and other parameters when programmingfunctions)

@ "BUSY" appears upon receiving 8 signal.

® S-me1er/RF output power meier

® AUlD Power Off.n.bIed@ low Battery Ind~ator (Flashes when needs

replacement or charge)

® low Power Output mode indicatorCD Alarm lunetton ONQ) Offset shift direction

® cress 'one encoder ON

®

@

®@

Lift the bottom tab and lift the battery-case cover. Insert three AA drycellsor NiCd battery cells here; close. and lock with the bottom tab.

• DISPLAY

©

® 00@"><:---;'-F:"""':;;..<:---x@®

"Speciftcalions and information found in this documenl ate subject to change w;thoul notice.ChcMce of NiCd battery is at user's risk.

• QUICK REFERENCE CHARTCondition Pressed while Press and hold and

KeyPressed alone

F is pressed tum the power on

F il released qUickly.reselIreq. change by digits

MaNI unmutes squelch keylocklunlock beeponloft

PTT transmits

Mem.llliltmodl:Channel IndicationVIM VFO- -Memory Solect eli by UP.oowNMode

key.&IJISSViVlo....

freq./mem up (scans if

UP pressed a while)channel step Courtesy beep ON(II pressed with PTT.

emits alert tone.)

Ireq.lmem down

DOWN(scans if pressed

tone Ireq. change Courtesy beep OFFawhile) (II pressed withPTT. emits alert tone.)

CAll call channel a1armon/oll a1erV1750Hz

scan startollsetSCAN With PTT. toggles

power Hi/Low programming

LAMP lampon/oll Auto Power 011 change lamp mode

Copyright © 1996 Alinco. Inc., Osaka. Japan. All rights re88Mld. No part 01 thismanual may be reproduced, copied. translated, or transaibed in any lorm or by anymeans without the prior written permission of Alinco, Inc.Names 01 products used in this manual are lor identilication or description purposeonly and may be trademarks or registered tredemarkS oltheir respective company.

V/M/MWIChanges between VFO and memory channel.To program a memory channel. (1) in the VFOmode, press and hold the F-key and press thiskey. (2) Use the UP/DOWN key to select a memorychannel number. (3) Preea thja key again tomemorize the displayed frequency (including theoffset and tone encoder) to that channel. Memorychannels avallabkt are: c. 0 - 19.

DOWNltonelPreas this key to change frequency/channeldownwards. Press this key while pressing theF-key to entre programming mode for the CTCSSencoder. Then preas this key to change theencoding tone frequency. Preas the F-key with thiskey again to the display/erase the a inthe LCD that turns onJofl the encoder. PressPTT to exit.Pressing the UP Of DOWN key while transmittingwill emil 1750Hz tone or the alerting ring to raisethe attention of the called party. This sound can betoggted between 1750Hz Of' the alerting ring bypress and hOlding the CALL key (see bek)w) andturning on Ihe power. Preea the UP or DOWN keyfor a few seconds to slart &Canning.

UP/step IPress this key to change freqooncy/channelupwards. Press this key white pressing lhe F-keyto entre programming mode for the channel step.Press this key to change the channel step. PressPTTto 8xit.

Microphone I

Speekerl

LAMP/APOIPress this key to illuminate the LCD for 5 seconds.Press and hotd the F-key and press this key totoggle the APQ (auto-power-off); Use theUP/DOWN keys to change the automalic powerott timer from OFF to 120 min. In 30 min. step.Press and hold this key and turn the power on.then the 5 second iIIuminaHon timer is disabled:the lamp ls togg~onion wUh the key regardlessot the time passed.

LCD

SCAN/SHIFT IPress thie key tOSC8fl. Press and hotd the F-key andpress this key to set the aemH;tuplex offaet treque,..cy. Each ptellS of .he key in the _ -inll modechanges the shift direction + Of - . PnIes PTT to exit.WhUe preeeing PTT. press this key to toggle traO$­mission 0U1PU' High/Low (LOW~ in .he LCDwhen In LOW' power mode).

CALUBELLIPreaaing 'his key changes)OUt' opere'ing frequencyto memory ch "C". Pressing again resumes theortginal frequency. Press and hold ,he F~ey andpress 1his key 10 lum onJoff the alann funcl:ton; thetuncUon alarms you with an electronic sound whena signalla received. (woppeara in ,he LCD.)

P_ switch and Volume 1----'

• OTHER FUNCTIONSa Cour1eay Beep: A short beep is emitted on your transmitting signal upon

each release 01 the PTT key. to lelthe other party "goaheed" and talk. Totoggle on this function, press and hold the UP key and turn on the power.To toggle all, do the same with the DOWN key.

a KayStrolul8MpSound: The beep heard with each stroke 01 keys can betoggled on/oil, by pressing and holding the MONITOR key and turning thepower on.

a Chennel Dleplay Mode: Only the memory channel number (and notthe Irequency) is displayed. "your operation is limited on your "usual"channels only, this aetting may be uselul. This mode can be entredlexitedby presslholding the VIM key and turning the power on.

Resetting: Press and hold the F-key and turn on the power.

• OPTIONSe Baftery Charger MW818 (220V AC input)a Headset w~h VOX EME·12 (Earpad type)

EME·13 (Earphone type)a Ti&-pin mic. and earphone with VOX . EME-15a Speaker Microphone _ EM5-9e Earphone Mic EME-4a Soft Case E8C-27eCar lighter DC cable with voltage conversion to 5.5V DC EDH-18a Mobile brackel _ EIIC-6a NiCd baftery·pack E -25Na Battery Charger eoCo79 (220V AC input)a Battery Charger eoCo78 (l20V AC input)

• CBOAHAFI TA5nM~ AflR nOnb30BATEIlRKHOnKa HIUKlITMe Ha xHonxy H8JIllITMe Ha xHonxy BXnlO'l8HMe nMTaHMII

npM H8JIllITOil XHonxe F npM HIUKlITOil XHonxe

M3MeHeHMe OAHoro B03BpaT xF (4)YHX14MII) 143 PUPIIAOB ~aCTOTbl

"Function" (npM XOpOTXOM Ha· npeAblAYIIIMM yCTa·JK8TMM) HOBxaM

KOHTPOflb OTxpblBaHMe WyMl>- OnoxMpoBxa MnM BXnlO'l8HMe MnM Bbl·"Moni" nOAaBMTenll pa30nOXMpOBxa xnlO~eHMe 3BYXOBbiX

XHonOK CMrHanOB

~Mr~P.A4A nepeAa~a

4 ACTOTA· 3anMCb B naMIITb:

nAMSlTb nepexnlO~eHMe BblOMpaTb xaHanOB no peJKMM MHAMXa14MM"VIM" ~aCTOTa - xaHan "UPIDOWN",M xaHanOB

HaJKMMTe VIM CHOBa.

YBenM~HMe ~aCTOTbl

MnM xaHana. npMAnMTenbHOM HIUKlITMM

BBEPX - cxaHMpoBaHMe. npM war xaHana BxnlO~eHMII 3yMMepa"UP" HIUKlITMM BMeCTe C nepexoAa Ha npM!!M

xHonKoil nEPEAA4AnBpBAaATcII CMrHanTpeBorM

YMeHbweHMe ~aCTOTbl

MnM XaHana. npMAnMTenbHOM HIUKlITMM

BHIo13 - cxaHMpOBaHMe. npM M3MeHeHMe ~aCTOTbl BbIKl1IO~eHMe 3yMMepa"DOWN" HIUKlITMM BMeCTB C TOHa nBpexoAa Ha npM!!M

XHonKoM nEPE,AA4AnepeAaATcII CMrHanTpeBorM

Bbl30B Bbl3blBHOlOt xaHan BXnlO'l8HM&- TpeBorM ... ~ 1750r14"CALL:' BblxnlO~eHMe 3BOHxa

clUlHMpoBaHMIICKAH. C XHOnXOIOt yCTaHoBxa cABMra"SCAN" nEPEAA4A,Oonbwoil/

lIanylO (Low) 1I0IllHOCTM)

nOACBETKA BKnlO~HMe·OTKnlO~eHMe M3MeHeHMe peJKMMa

"LAMP" BblKnlO~eHMeaBTOBblKnlO~aTenll nOAcBeTxM AMcnnellnOAcBeTxM AMcnnBII

• DJ-S11 VHF ~~~fl'ltnji

Ii II .~lil' .!:;iFiI-gifJlJ 1i1'#1fJiSl@.iIl

F lIIt'@'ilill¥JtJ:roP~'l UMIt~

MONI PJIJf 11., Jf1JtIl. BeepPJJfI ~

P'IT ~M

~iC.tl.mil:

VIM VFO E,iiCtUail~lljUlUPIDOWN.

lail~>FE,iM.~>F!illji1filiMJm, J!ftltVIM.

\. M.E,iji1fill:1t

UP2.*tJ:;9Btfi~t M:it'illfAlt Beep)ll'ifMtl3.E,iP'IT-t!:ltJll~IIfA4

1U~i!\%

\.M.E,imil-r,.

OOWN 2.*tJ:;9Btfi~tcrcSSIIf.Mi.i~ Bcep)ll'ifMtl

3.E,iP'IT-t!:ltJll~IIfA4

.~i!\%

CALL IIfA4fil"iI t'%Jf/~ ~1IIilE,i 17S0Hzgl~if%!ill

BtfiSCAN ~ PTI -t!:ltJll~M.lli ~MMi.i~

!illiflj/~ (Low)

LAMP ~)It~>F*/~ (ji;/):X;tn.ill:~ ~'l~)It~>FfIj.t

• MODE D'EMPLOI

Touche Pressez seulement Maintenez F et Maintenez la touchepressez et remettre I'appareil

FPressez pour I'instant, pour Reinitialisation

(fonction) changer la frliquence en (Reset)digit de lMHz

MONI Ouvrer Ie squelch pour Verrouillage desactiver/activerecouter les signaux faibles Bip

PTT emitter

Mise en memoire:

VIM VFO (commande crantee) choisir Ie canal par mode d'affiche Nr.+- -+ Memoire UP/DOWN, et appuyer de Canal

VIM encore.

freq./mem. vers en hautactiver Ie bip de

UP ~alayage si maintenu). pas des canauxi pressee avec PTT, commence d'ecouteemittera sono d'alerte.

freq.lmem. vers en basdesaetiver Ie bip de

Down (balayage si maintenu) selection des tonsSi pressee avec PTT, cress pour codage commence d'ecouteemittera sono d'alerte.

CALL cana'''C''activer/desactiver changer entre ton-I'alarme alert et 1750Hz

commence balayage(scan start).

SCAN Avec PTI, changer la Decalage relaispuissanceHaut (Hi)/Bas (Low).

LAMP eclairer Ie LCD ArrAt automatique changer chrono-(APO) graph de la lampe

.OPERACION BASICA

teclado pulse solamente empuje cuando F empujado este teclado,esta empujado enciende el radio

F Pulse rapidamente para

(Funci6n) cambiar la frecuencia en re-iniciodigit de 1MHz

MONI abrir el squelch para escuchar bloqueo/libre de tonos de avisolos seliales debiles teclado desactivar/activar

PTT Transmitir

programe la mem.:

VIM VFO (Dial por sintonizar) Elige CH por UPI modo de indicaci6n+- .... Mem6ria DOWN, yempuje del nro. de canal

VIM otra vez.

aumentar el Nr de free./mem.

UP (cuando empujado par s~un- paso de sintonia activar el tono dedes ysi empujado con P , sintoniatransmije el tono de alerta)

disminuye el Nr. de free.lmem.

Down (cuando empujado par~un- Selecci6n de desactivar el tonodes ysi e"1lujado con P , subtonos CTCSS de sintoniatransmite el tono de alerta)

CALL canal"C" activar/desactivar cambio tono-el alarma aiertal1750Hz

comenzar barrido (scan). frecuencia deSCAN Con PTI, cambio desplazamientopotencia de salida

Hi (Alta)/Low (Baja) (off-set)

LAMP lIIuminar la pantalla LCD desconexi6n cambio tiempo porautomatica (APO) illuminar

EI marcado CE que aparece en los productos indica que se han certificado de acuerdocon la Directiva EMC 89/336/CEE Y la Directiva sobre Bajo Voltaje 73/23/CEE, enlos casos en los que les sea aplicable. Los productos satisfacen la Normativa deCompatibilidad Electromagnetica: EN 50081, Normativa General sobre Emisiones yCompatibilidad Electromagnetica; EN 50082, Normativa General sabre Inmunidad.

• CPU UnitDISPLAY

~l'lll • &&P'11' I 1 I 1 1 I l" S ,

1:5 I _

~r~"""-~ --~ ....-~_./_ OCMN

~-

ilf -tiif. _,_ --~-=41 ~I~L. Iwc""" L, : 1m :c~ 'I" - 'r"" ~ ~nl~ ~WW~ ~ r~~~~ r~~ ~§ 1!1 :1:1'1

8I~~~ ~O ,\I~'\'&'&&&';X!1';I!! I !lj!ll~,.f..oa!!.! r::;:.'-....11.-.1__ ~ : • 7 • ~ .. loft 2 ~ ~ r ~ 1 ~ S:'~

... woe ~! 1m •••." ~!1 Ii.~ ;jJ'~:- ~ r- ~~ ::'~- 1.1 iI' -iff'I:' ~'I'ii .... C:±.. _ ,,~L,r-''j' ~,.. a! Ii ;. ~~ In C'" .x) _" ::."~..:.. r· .... r- :r~ ,. ."'. .. ''''' ." ::?,UIQ(,ItJIII :!;r; ml c_ L.L[IClIl; S1.!1

~<0U-4I'" I :!:0::&1 ~ L.::lL (tDfolA S1.

1; 5:1 T':ll:'" i'.I\:ill:'>l1 :: .... ::; ::

~'~.i:l!' I~' S. .Bll........:II'] IA: ~ :/il :. ":;~j)J"1.. I' f,l,. I.. e! .... '" l" .,. ,,~-- ; 1-;;1lI O<V ....,. <- ~! ,:J!!-:: "~I

Sl"UlKut 1\1 2 I'?- mr ~ tlI 'J~

~! 'I ~~~Ih ~ni "j;;D • c,. • • "~• 'fI ~.fur-_~ ~ ~., 1'"" ~~ i ! =:Ol _ C :" t ~ r ! : i i ~ i , r ~ i ~ ~ ",.......e;r ~t J,~" , 8~J. .;~.. i'lI. ~ ~ ". I!\ I! ~! Ii lnnJ~ I~ :, WJ~Pir ±3; :w ~l:' d!!~,i l~ 'I:' I a B Ii Ie ~ I-J

'='~~ ·W·-" er * ~~ ~lI!r I a: "b,~i 1;: Hr ~.~ rFr }":": ~~[POw<-':: I' ~ iI~! ,. ~ t! "'" ~~I~D!! £fla: ±a! ~ II':': I r1'-, ,."' -. ~ c::.... r~ I':" ji~ L.... ::::::'~1l L~ ~ ~ -rr. 1 g 't:: 'tl _ J.~ , ~

()WlC(~ Q~. C»I 1t3~ O<»I:;......!:~ .11 f<>! i ~r~ ,••w -~ l'" ~ tl "" _ I ~ K!

~; - ti t;;,·~lili~!- ~,b ~I- 1±5l .wt!J .~U~c ,n, • D: ~..... .L: ro:;;o-i!~! ~I5 ! I \'ii ~~!f a; l I . .to

l=t.. f--.. V'L · ITw

I...... I 'II '" ex f ~.... j b~ ~r rp;,r-l' ...... '"..~~i !~lp' ~,'/.. ~:1,',' .. f-{f !P ~l I :: t,,,,, ,,~,,~nL 141: ',4~J.l!:iI~~ 1 ""Al~il l~ ~ ~~!... I'i"~ ai,pHxU XXXX

• RF Unit

till.... ~;;u

~H h+-H+H

NOTE: This equipment has been testedand found to comply with the limits for aClass B digital device, pursuant to part15 of the FCC Rules. These limits aredesigned to provide reasonable protec­tion against harmful interference in aresidential installation. This equipmentgenerates, uses, and can radiate radiofrequency energy and. if not installedand used in accordance with the instruc­tion manual, may cause harmful inter­ference to radio communications.However, there is no guarantee thatinterference will not occur in a particularinstallation. If this equipment does causeharmful interference to radio or tele­vision reception, which can be deter­mined by turning the equipment off andon, the user is encouraged to try tocorrect the interference by one or moreof the following measures:

• Reorient or relocate the receivingantenna.

• Increase the separation between theequipment and receiver.

• Connect the equipment into an outleton a circuit different from that to whichthe receiver is connected.

• Consult the dealer or an experiencedradiofTV technician for help."

~ ...

,..n

38~ h

• veoUnit

'",-

e:tII.l. .l.r.; -'··'1 1'11I -6-' -, - - - --

[.!)( ]5H

·~so

~

;It iI~ T i fi;.;;;+, ,':I 1l:.,::4·''''i 1:1 .:~ IE! ,_ -IP"."r __ I *el~ .,. c;:~~_