verve - Focal Point Lights › sites › default › files › FV3S_IS0196_0.pdfIS0196 Rev. H 2016...
3
IS0196 Rev. H 2016 ©Focal Point, LLC 4201 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 3 1 3 4 5 2 verve ™ III FV3S FOCAL POINT OPTIONAL DUST COVER UNIT DESCRIPTION FOLLOW FOCAL POINT INSTRUCTIONS FOR UNIVERSAL SUSPENSION SYSTEM ASSEMBLY. SEE IS0166 UNIVERSAL SUSPENSION SYSTEM - SHIPS SEPARATELY KEY Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. MAKE ELECTRICAL CONNECTIONS ADDITIONAL INSTRUCTIONS IS0166 POWER OFF U - INDIVIDUAL S - START OF RUN I - INTERMEDIATE E - END OF RUN POWER ON LEVEL ATTENTION KEEP LUMINAIRE IN ORIGINAL CARTON UNTIL READY TO INSTALL. DO NOT REST ON THE GROUND. KEEP LUMINAIRE IN ORIGINAL CARTON UNTIL READY TO INSTALL. USE CRADLES TO SUPPORT LUMINAIRE, DO NOT REST ON THE GROUND. PLASTIC PACKAGING SHOULD ONLY BE REMOVED AFTER LUMINAIRE IS INSTALLED LOCKING SCREW ALLOWS FOR Y-CABLE ADJUSTMENT 8.25” W (+/- .10”)
Transcript of verve - Focal Point Lights › sites › default › files › FV3S_IS0196_0.pdfIS0196 Rev. H 2016...
IS0196 Rev. H 2016 ©Focal Point, LLC 4201 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 3
1
11113 4 115
112
verve™ III FV3S
focal point
optional dust cover
unit description
FOLLOW FOCAL POINT INSTRUCTIONS FOR
UNIVERSAL SUSPENSION SYSTEM ASSEMBLY.
SEE IS0166
universal suspension system - ships separately
key
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing.
make electrical connections
additional instructions is0166
power off
u - individual
s - start of run
i - intermediate
e - end of run
power on
level attention
keep luminaire in original carton until ready to install. do not rest on the ground.
keep luminaire in original carton until ready to install. use cradles to support luminaire, do not rest on the ground. plastic packaging should only be removed after luminaire is installed
locking screw allows for y-cable adjustment 8.25” w (+/- .10”)
IS0196 Rev. H 2016 ©Focal Point, LLC 4201 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 3
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing.
BALLAST SERVICE
76
8
1 2
IF LUMINAIRE/RUN IS TWISTED
LOUVER REMOVAL
OPTIONAL DUST COVER
grip here, not on end cap
hold louver in place while releasing levers to prevent damage
A
A
B
B
C
C
fasteners indicate ballast locations
installed
flex to install
x4
Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited.
IS0196 Rev. H 2016 ©Focal Point, LLC 4201 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 3
EMERGENCY
SEE BATTERY MANUFACTURER INSTRUCTIONS
emergency maximum mounting height: 8.00'
