Vertical Inkjet Cutting Plotter User manual...2017/06/06 · 1.3.1 cartridge type H8 series of...
57
www.han-bond.com Vertical Inkjet Cutting Plotter User manual
Transcript of Vertical Inkjet Cutting Plotter User manual...2017/06/06 · 1.3.1 cartridge type H8 series of...
www.han-bond.com
1
Preface
Thank you for choosing Han-Bond H8 plus vertical inkjet cutting plotter.H8
plus vertical inkjet cutting machine can be widely used in drawing, cutting a large
garment marker, cases and handbags styling, engineering drawings, models and
other fields, the graphics cutting quality has reached the international first-class
results. In your use of the vertical inkjet cutting machine before, please read
<user manual > carefully to ensure that you can efficiently and successfully
complete the machine operation. All the features of the products for more
information please pay attention to our website www.han-bond.com.
(this manual is subject to change without notice)
www.han-bond.com
2
Catalog
Preface..................................................................................................................................... 1
Catalog..................................................................................................................................... 2
Safety instruction.....................................................................................................................5
Matters needing attention......................................................................................................7
Chapter 1 assembly............................................................................................................... 12
1.1 Open box and check components...........................................................................12
1.2 machine installation................................................................................................12
1.3 install HP45 cartridge.............................................................................................. 13
1.3.1 cartridge type.......................................................................................13
1.3.2 cartridge installation.......................................................................13
1.3.3 ink exhaustion mark...........................................................................14
1.3.4 change ink cartridge...........................................................................15
1.4 mounting tool holder.............................................................................................. 17
1.4.1 assemble and disassemble Han-Bond blade holder......................17
1.4.2 Han-Bond blade holder assemble diagram......................................18
1.4.3 The use of han-bond blade holder.................................................. 19
1.4.4 Han-bond blade.......................................................................................19
1.5 machine connection................................................................................................20
1.5.1 connection USB data line.................................................................. 20
www.han-bond.com
3
1.5.2 connection of power cord.................................................................. 20
1.6 install printing / cutting papers...............................................................................21
Chapter 2 installation and use of the output center.........................................................23
2.1 output center installation (example: win7 64 bit or above computer operating
system)...................................................................................................................................23
2.2 the use of the output center...................................................................................28
2.2.1 graphic direction setting................................................................ 28
2.2.2 page settings.........................................................................................29
2.2.3 page header and footer settings.................................................... 29
2.2.4 language selection...............................................................................29
2.2.5 print segment length settings........................................................ 30
2.2.6 Print Preview.........................................................................................31
2.2.7 print output...........................................................................................31
2.2.8 file conversion and save.................................................................. 32
Chapter 3 installation drive...................................................................................................33
3.1load driver (for example : win7 64 bit computer operating system)33
Chapter 4 control panel.........................................................................................................38
4.1 control panel............................................................................................................38
4.2 key note................................................................................................................... 38
Chapter 5 Calibration.............................................................................................................42
5.1 offset calibration..................................................................................................... 42
5.1.1 calibration nozzle dislocation...................................................... 42
www.han-bond.com
4
5.1.2 calibration of row spacing dislocation......................................43
5.1.3 calibration cartridge tilt misalignment....................................44
5.2 precision calibration................................................................................................45
Chapter 6 failure analysis......................................................................................................54
6.1 control panel error and solution.............................................................................54
6.1.1 X encoder error.......................................................................................54
6.1.2 display "AAAAAA"..................................................................................55
6.2 other issues analysis................................................................................................55
Chapter 7 contact way...........................................................................................................56
www.han-bond.com
5
Safety instruction
Please carefully read all the following instructions before using the
vertical jet cutting machine:
Place the machine on the level ground, avoid putting it on an unstable surface
caused unnecessary fault.
It is forbidden to connect the machine to the attachment with non rated
voltage. The power supply is not stable, which leads to the decline of the
performance. Even burn the power of the machine.
Power plug should be inserted in the power socket with ground wire (do not
remove the top of the plug pin), to ensure the device to be well electrical
grounding . If the machine is not grounded, may be due to excessive
accumulation of electric charge and discharge, harm to the human body, it
may cause the machine components burned.
Avoid connecting machine and high power devices to the same power
socket(such as shadow printing machine, air conditioning, air compressor,
CNC machines and other equipment); if in parallel with one power supply
socket, please make sure the device power shall not exceed the power supply
socket wire can bear the maximum current.
And the prohibition of pulling power line, do not use damaged or worn power
line, otherwise it may cause electric shock, short circuit or fire.
www.han-bond.com
6
When you do not use the machine for a long time, pull the plug from the
power outlet
Unplug the power plug before cleaning the machine.
Do not drop the liquid into a vertical jet cutting machine, otherwise it will
cause the circuit board of the machine to short circuit and destroy the
component.
Do not block up or place goods inside of the machine
During the machine working, prohibit reaching your hand into the vertical
inkjet cutting plotter, touching the head(dolly group) or inside of machine
parts.
Unless the product "Manual and warranty guidelines" are described.
Otherwise, please do not to self repair or disassemble the machine
www.han-bond.com
7
Matters needing attention
Although you may be familiar with the H8 series vertical inkjet cutting plotter,
please read the following carefully before you operating the machine:
Machine usage environment
The machine works and storage temperature: 10-35 degrees Celsius, do not
store or use it in a strong light irradiation, radiation or heat. place.
Working humidity of the machine at room temperature range: 20%-80%, do
not use it in wet and dusty place. Because once the water vapor condense
inside the machine, dust go into the inside of the machine, will cause short
circuit or poor contact and seriously affect the performance of the vertical
inkjet cutting plotter.
To avoid strong electromagnetic interference or put things with magnetic
near the machine.
Other matters
Do not use the hand to move the car(head) fast, otherwise the current will
damage the machine’s main board.
In addition to there are instruction in this manual, please don't try to
lubrication the machine, otherwise that may lead to machine not work
properly.
www.han-bond.com
8
Before you connect or disconnect the power supply, make sure the machine is
in a shutdown state.
When you end the use of machine, please keep the machine with dust cover
well to prevent dust from entering.
To avoid unnecessary frequent opening and closing machine, so as not to
affect the performance of electronic components
www.han-bond.com
9
Introduction
Thank you for choosing Han-bond H8 series vertical inkjet cutting plotter. H8
series vertical inkjet cutting plotter all in one machine adopts double feeding
paper system (white paper and kraft paper can be loaded at the same time), and
can be used to drawing, cutting large format of clothing mark, luggage break the
pattern, engineering drawings, model etc., graph cut drawing quality reached the
international first-class results. H8 series vertical inkjet cutting plotter machine’s
servo system is with high accuracy, fast speed, stable effect, can be compatible
with domestic and foreign clothing CAD software.
www.han-bond.com
10
Basic performance index
vertical inkjet cutting plotter
Model No. H8 Plus-120 H8 Plus-170 H8 Plus-190
Max drawing area 1200mm*limitless 1700mm*limitless 1900mm*limitless
Max feeding paperwidth 1250mm 1750mm 1950mm
Loading paper mode Wheel feeding paper , automatic feeding paper (double feeding paper system)
Transmission mode Han-Bond printing system+USB2.0
Original coordinatesetting
Can self set base point
Knife standarddiameter
2mm
Cutting thickness 60g-300g,accurate、stable,cutting thickness is leader in the industry
Maximum speed Inkjet 90m2/h, cutting 120cm/s
Nozzle No. 2PCS
Compatible cartridge HP45
Resolution ratio 600dpi/300dpi
Compatible format Any format (domestic and foreign clothing CAD software)
MechanicalResolution
0.025mm/step
Software resolution 0.05mm/step
Absolute accuracy 0.15% or 0.1mm
Repeatabilityprecision
0.2mm below
Concidence deviation <0.5mm
Knife pressure 10g-300g
Drive mode Servo. step
Power supply 50/60HZ，110V / 220V, 220W
www.han-bond.com
11
Computer system requirements
System Microsoft Windows XP and above
CPU Intel Core i5
Memory 2G or above
hard disk 500G above the hard disk
CD-ROM 4 times above CD-ROM
USB USB2.0 port
www.han-bond.com
12
Chapter 1 assembly
1.1 Open box and check components
List of components: main machine x1, tripod upper beam x1, tripod down
beam x1, left foot rack x1, right foot rack x1, universal casters x4, paper collection
roller X1 article, send paper drum X2, clutch paper cone x4, paper pressing rod X2,
HP45 ink cartridge X2, Han-Bond blade holder x1, han-bond bladeX3, assembly
screws X1 set, 5mm inner hexagon spanner x1, 3mm inner hexagon spanner x1,
power line x1, USB data cable x1, installation CD x1.
1.2 machine installation
Figure 1 machine parts drawing
www.han-bond.com
13
Name of all parts of the machine
1, the right side board 2, left and right foot plate
3， right tripod 4, left tripod
7, ink frame connecting plate 8, H8 slide
9, H8 tray 10, grinding wheel brace plate
13, ink cartridge mounting seat 14, press paper plate
15, Sensor holder 19 idler wheel group
21, collect and press paper bar group 22,paper collection roller group
35 paper feeding motor 36, roller base
44, universal caster
1.3 install HP45 cartridge
1.3.1 cartridge type
H8 series of vertical inkjet cutting plotter machine use HP51645 model
cartridge, in order to ensure the quality of printing, it is recommended to select
the authentic cartridge, HP supplies store sales.
1.3.2 cartridge installation
Cartridge installation example (see Figure 3):
www.han-bond.com
14
Figure 3 cartridge installation example
1.3.3 ink exhaustion mark
The ink in the ink cartridge is constantly consumed in the drawing process;
ink exhaust mark will gradually change from green to black; if the mark is
changed to black completely, indicating that the cartridge has run out of ink,
need to replace the cartridge (see Figure 4).
www.han-bond.com
15
Figure 4 ink exhaustion mark
1.3.4 change ink cartridge
When you need to replace the cartridge, please turn off the power of the
machine, plug in/off the cartridge should be cautious. Before printing a long file,
it is best to check the amount of ink cartridges, try to avoid in the middle of the
print to change cartridge.
1.4.5 cleaning cartridge
If the printing graphics have some points or lines not printed (see Figure 5),
you need to clean ink cartridge.
Fig. 5 Comparison of printing effect
www.han-bond.com
16
Figure 6 clean electronic contact 7 clean electronic cartridge PCB
Manual cleaning
A Clean the electronic contacts in the cartridge with a dry cotton swab (see
Figure 6).
B use dry cotton cloth to wipe the ink cartridge side PCB (see Figure 7) to
avoid damage to the PCB, should only be wiped once.
C To clean nozzle by non-dust cloth or cotton with alcohol(see picture
8,9,10).
Figure 8 cleaning cartridge nozzle
www.han-bond.com
17
Figure 9 before cleaning figure 10 after cleaning
1.4 mounting tool holder
1.4.1 assemble and disassemble Han-Bond blade holder
Unscrew the hand nut , then you can pull up.
www.han-bond.com
19
1.4.3 The use of han-bond blade holder
Han-bond blade holder has a gear adjustment function (0~11 gear), to
adjust the Han-bond blade holder length is more simple, quick and accurate.
Position Description: The top of the knob marked with 1/2/3/4/5/6 numbers,
the initial state (counterclockwise twist in the end) as "0", the number 1 is "gear 1
" (when the blade length is about 0.099 mm, and so on each gear blade length
increases about 0.099 mm, when go to gear 11 the blade length is about 1 mm),
between number 1 and number 2 it’s “gear 2”, number 2 is " gear 3 ", and so
on the number 6 is " gear 11 ". Special note: clockwise is increase the gear and
counterclockwise direction is to decrease the gear, when install the blade must to
counterclockwise decrease the gear to" 0 ".
When you cut different materials, can directly adjust gear according to the
material, save the time of changing paper or blade , for example: cutting 250g
kraft paper, Han-bond blade holder can be adjusted to "gear 3" (adjust the blade
length of about 0.297 mm). Note: due to the material density is different
etc.reasons, blade length adjustable there will be differences, it is also related to
the degree of loss of the blade edge and the setting of the machine parameter.
1.4.4 Han-bond blade
Han-bond blade is a Japanese custom made diamond blade, it’s the 3~10
times of life than normal blade.
www.han-bond.com
20
1.5 machine connection
1.5.1 connection USB data line
First to turn off the machine power, and the USB data line and machine
connection point need to use "can stick type fixed seat" stick firmly, prevent
because of external pull to damage the machine.
(line buckle fixed effect diagram)
1.5.2 connection of power cord
When the power switch is in the state of '0' disconnect state, one end of the
power supply line is connected with the machine, and the other end is inserted in
the power supply board which is provided with a reliable ground wire protection.
If machine power supply is abnormal, please don't try to hold on to turn on
the power switch, should immediately unplug the power line, stop related
operations and contact with the dealer, feedback about the situation, identify
and eliminate all problems then can use.
www.han-bond.com
21
1.6 install printing / cutting papers
The print / cut paper instruction: weight: 40-300g, tube diameter 60~75 mm,
fiber container quality is less than 50kg.
H8 vertical ink jet cutting all in one machine, when it’s in the use of cutting
mode( kraft paper (120g-300g) , the pressure wheel of the corresponding feed
grinding wheel wheel need to be fully pressed well, when it is in the use of
drawing mode(garment mark paper, computer paper, kraft paper (40-120g),
need to symmetric select five pressure wheels and press it them well (less than or
more than 5 wheels to press the paper that will all affect printing effect).
www.han-bond.com
22
Feeding motor switch of H8 plus vertical jet cutting machine can controlswit
ch betweenthe middlepaperfeeding motor (Kraft paper) and bottom paper feedi
ng motor (tail paper) ,If you need to usemiddle paper feeding motor (kraft pape
r), you need to switch to position, if you need to use the bottom paper feedi
ng motor (tail paper) then you need to switch to position,If you need to turn
off all the feed motors, you need to switch to O position.
www.han-bond.com
23
Chapter 2 installation and use of the output center
Note: when you select output center installation package, Windows XP, win7
32-bit computer operating system choice running the file "Han-Bond print
system 32bit"; win7 64 bit or above computer operating system choice running
the file "Han- Bond print system 64bit"!
2.1 output center installation (example: win7 64 bit or above computer
operating system)
Run folder "Han- Bond print system 64bit- Print Center _USB interface
--Han-Bond Print System 64bit"
www.han-bond.com
27
Click "finish".
Install is completed and run Print Center
Computer operating system for the installation of win7 64 can refer to
the steps of the computer operating system windows XP! But the loaded file
that need to select the file "Han-Bond Print System 64bit ".
www.han-bond.com
28
2.2 the use of the output center
Han-Bond print system is a PC terminal software presented by Han-Bond
company, its functions include graphics browsing, printing, as well as graphics
editing and text notes, etc..
Before using, be sure to adjust the following settings options!
2.2.1 graphic direction setting
When the output is installed for the first time and need to set the image
direction and open a PLT files (random CD in attached file), In turn by the “ set -
Options - automatic rotation 0 degrees” to adjust the parameters, to ensure
that the graphics in the right direction.
www.han-bond.com
29
2.2.2 page settings
Open the page settings, to confirm that the scaling ratio is 100%.
2.2.3 page header and footer settings
Header and footer: do not click the "use header print" and “use footer to
print". (usually print clothing marker is not required for headers and footers,
users can also fill the content in the blank, self definition of headers and
footers)
2.2.4 language selection
In the settings window second item can also be carried out setting in English
and Chinese.
www.han-bond.com
30
2.2.5 print segment length settings
When chose cutting function, the segment length is set to 300mm, before
debugging pettifoggery coincidence it also needs to set the segment length to
300mm;
In the selection of the drawing function, the segment length does not need
to set, the default length of the software is 500mm.
www.han-bond.com
31
2.2.6 Print Preview
Open print preview, or click on preview the ready to print graphics.
2.2.7 print output
Open the print options or click , and enter the required number of print,
and then click OK".
www.han-bond.com
32
2.2.8 file conversion and save
Han-Bond print system support Plt. Dwg. Dxf and other types of print file to
save as conversion.
www.han-bond.com
33
Chapter 3 installation drive
Note: When do printer driver installation, Windows XP, win7 32-bit computer
operating systems selected the folder "win7 32"; win7 64 bit computer operating
systems selected folder "win64bit". When installation, please must to select the
manual loading.
3.1load driver (for example : win7 64 bit computer operating system)
Copy and save the file, copy the "win7 64" folder which under the same
folder of this user manual folder to the computer at any location (in order to
facilitate the search, it is recommended to save it to the computer D disk).
Make sure the USB data line to be securely connected on the machine, and
turn on the power switch of the machine, the computer will be prompted to
"update driver software (Han-Bond Printer)", began to enter the installation
process.
www.han-bond.com
34
Select "browse the computer to find the driver software (R)"
Click “browse"
www.han-bond.com
35
Select the "win7 64" folder in the first step copy path, open the "win7 64"
folder that under "win7 64" folder , click “OK” after selected.
Click "next"
www.han-bond.com
37
After the successful installation of the Han-Bond Printer driver, turn on the
power switch of the machine (the USB data line is in the connected state). Test
methods: 'my computer' position with the right mouse button to choose
"properties", open the "device manager", in the "universal serial bus controller"
can see the 'HAN-BOND Printer Generic Drive(3.4.7.000), which indicates that the
drive and connection is normal.
www.han-bond.com
38
Chapter 4 control panel
4.1 control panel
The control panel is a human-computer interaction platform vertical spray
machine cut, the current state through a liquid crystal display device can
understand the machine; on the other hand, it is convenient for the operator to
realize feed wheel forward, back, left and right moving ink frame (drawing point
selection), the process of drawing the pause, stop, adjust the machine
parameters, dynamic self. A paper cutting operation and other functions.
4.2 key note
Figure 11 Key-press panel
www.han-bond.com
39
【 】 —— draw back paper
【 】 —— paper feed
【 】 —— Left shift ink box group
【 】 —— right shift ink box group
【 】 —— Cancel the current print job
【 】 —— One key cutting paper function
【 】 —— One button entry test mode (b1~b5)：
"b1. test X axis motor"
"b2. test Y axis motor"
"b3. test cutting"
"b4. test ink jet"
"b5 test cutting"
【 】 —— In the drawing process, if necessary，Press【 】，Vertical
jet cutting opportunity is in a suspended state，Press again【 】Continue
drawing。Standby state，Press【 】Is to redefine the origin of the machine，
Long press this button for 3 seconds to restore the data to the factory settings；
In settings，Press【 】Data save。
【 】 —— Enter settings，Press【 】，【 】Scroll parameter settings，
Press【 】，【 】Parameter addition and subtraction，Last press【 】Save
and exit。
www.han-bond.com
40
Parameter setting check list:
Parameter setting
1. Ink jet speed [ MIDIUM ]
2. Ink jet head split [ 0.00 ]
3. Nozzle coincident [ 0.00 ]
4. Row spacing split [ 0.00 ]
5. Ink jet speed shift [ 13000 ]
6. Row spacing join [ 0.0mm ]
7. Nozzle selection [ ALL ]
8. Ink jet head selection [ ALL ]
9. Ink jet effect [ CLEAR ]
10. Cutting speed [ 80cm ]
11. Full cut pressure [ 390g ]
12. Half cut pressure [ 270g ]
13.Half cut pressurecommand [ SP9 ]
14. Cutting length [ 50mm ]
15. Cutting space [ 0.2mm ]
16. X coincident set [ 0.0mm ]
17. Y coincident set [ 0.0mm ]
18. X axis scaling [ 1000.0 ]
19. Y axis scaling [ 1000.0 ]
www.han-bond.com
41
20. Ink jet head maintenance [ OPEN ]
21. Tool nose radius [ 0.00mm ]
22. Cut paper [ CLOSED ]
23. Collect paper motor [ OPEN ]
24. Paper type [ Thick ]
25. Language [ English ]
26. Factory Reset [ Press OK 3” ]
www.han-bond.com
42
Chapter 5 Calibration
5.1 offset calibration
Shipped along with the machine there is a disk, select PLT test file
"1000X1000.PLT" in the disk, and print.
firgure7 test file 1000X1000.PLT
5.1.1 calibration nozzle dislocation
When the nozzle is dislocation to the right side (Fig. 8), increase parameter
value in the 2nd item [nozzle dislocation] parameter, otherwise, decrease the
value;
www.han-bond.com
43
Figure 8 sprinkler head dislocation
5.1.2 calibration of row spacing dislocation
If row spacing dislocation is to the right side (for example, figure 9 left),
increase the parameter value in the parameter set of 4th item [ spaced
dislocation ], contrary to reduce numerical;
When the row spacing front and back is disconnecting dislocation (for
example, figure 9 ) , reduce parameter value of the parameter setting item 6 [row
spacing docking], and conversely increased the parameter value;
www.han-bond.com
44
Figure 9 spacing dislocation
5.1.3 calibration cartridge tilt misalignment
Ink box frame’s tilt lean to the right dislocation (FIG. 10 cases, right), tighten
the spring adjusting screw on the left of the ink holder. (Before adjustment, the 2
fixed screws on the left of the ink box rack must be all unscrewed)
Ink box frame’s tilt lean to the left dislocation (FIG. 10 cases, left), tighten
the spring adjusting screw on the right of the ink holder.(Before adjustment, the
2 fixed screws on the right of the ink box rack must be all unscrewed).
www.han-bond.com
45
Figure 10 ink box tilt adjustment
5.2 precision calibration
Due to the existence of the CAD software of the clothing coefficient error,
before using vertical ink jet cutting all in one machine must to be carried out
precision calibration, the user can through "Han-bond printing system" or
"clothing CAD software” to realizing graphic precision correction. To correct
"clothing CAD software", please consult the software company, following are the
correction method of “Han-Bond printing system"!
Note: the same software corresponding to the machine is with same
compensation coefficient, it needs to re -adjust after changing the software !
Calibration print 1000X1000mm rectangular file to do calibration, the file
need to use the corresponding clothing CAD software to generate.
www.han-bond.com
46
Print 1000x1000.plt calibration file
Measuring the actual print length, for example: the feed paper direction is 999mm
www.han-bond.com
47
In Han-Bond printing system click "Settings"--> “ option. "
Click on the right side of the “paper feeding direction “.
www.han-bond.com
48
Enter the design size and the actual size, and click "OK"
www.han-bond.com
49
Han-bond printing system automatically help you calculate the
compensation coefficient of “feed direction"
The setting method of compensation coefficient in the” direction of the
car “ is the same as above!!!
www.han-bond.com
50
5.3 pettifoggery coincidence set
Shipped along with the machine there is disk, select test file "H8 pettifoggery coincidence
set " in the disk and print,
Start debugging pettifoggery coincidence.
Note: before the operation, the segment length of the output center must be set
to 300 mm
www.han-bond.com
51
Now to analyse the printed and cut file:
Figure 11 X/Y coincidence effect diagram
("---black line" is ink jet lines, --- "red line" is cutting line)
Note: all of the following parameters must be adjusted during machine in the
standby mode or during ink jet period. If it’s in the parameters of the
adjustment during the cutting process are not valid.
The first step: take (Figure 11) "a reference position" as an example, when the
cutting line in the right-hand of ink jet line, need to increase the control panel
item 16th [x axis coincides set] corresponding value, contrary to reduce
numerical;
www.han-bond.com
52
The second step: take (Figure 11) "B reference position as an example, when
the cutting line in the jet line below, it needs to increase the control panel
seventeenth [Y axis coincidence set] the corresponding value, contrary to reduce
numerical;
Complete the debugging of X, Y axis of the coincidence set
Again to print the file "H8 pettifoggery coincidence settings file, start
debugging pettifoggery scaling.
Note: reference E reference position, after adjusting the X/Y axis coincidence
set, then you can to carry out this operation.
Figure 12 X/Y coincidence effect figure 2
("---black line" is ink jet lines, --- "red line" is cutting line)
www.han-bond.com
53
The third step: take (Figure 12) "C reference position" as an example, when
the cutting line in the right-hand of ink jet line, reducing the control panel item
18th [X-axis scaling] corresponding value, otherwise to increase the value.
The fourth step: take (Figure 12) "D reference position" as an example,
when the cutting line in the jet line below, the need to reduce the control panel
19th [Y axis scaling] the corresponding numerical value, and on the contrary to
increase the value;
www.han-bond.com
54
Chapter 6 failure analysis
6.1 control panel error and solution
6.1.1 X encoder error
Solution:
1．Check the sensor head in the dolly board and grating ruler’s assembly
position, if grating ruler is not in the middle region of sensor groove, need to
adjust it well.
2．check the grating ruler paste is loose, loose grating ruler can not
guarantee the accuracy of the sensor area, please be carefully tear off and
re-paste it by using the double side adhesive;
3．check whether the surface of the grating ruler is contaminated with dirt,
wipe clean with cotton cloth;
4． to check whether the appearance of the grating ruler is worn, the worn
grating ruler can not guarantee the accuracy of the grating, please replace it
immediately;
5．grating ruler under the strong light, may affect the accuracy, please avoid
the glare of the area;
6．check X axis direction of the belt is off or broken;
www.han-bond.com
55
6.1.2 display "AAAAAA"
Solution:
1. need password to unlock, please contact the dealer.
6.2 other issues analysis
1.each time to print file, the front section of the print blank or print is not
clear, may be the indoor temperature is too low, indoor temperature is less
than 10 degrees, it is recommended that the machine be moved to work in
the studio with heating supply.
2.The machine in the printing process, if the car suddenly left and right jitter,
it may encounter strong interference source, please immediately shut down
and eliminate interference.
3.Print line is dotted line, please shut down machine and pull out cartridges,
then use cotton wipe ink nozzle; cleaning method refer to (Figure 18).
4.If the printed line moves along the direction of the nozzle there is a gap of
about 2mm wide blank, and nozzle each movement appear the same
problem, may head is not in place or loose cable plug nozzle.
5.Car around a large difference between the left & right scanning speed, may
be the fault of the transverse servo motor.
www.han-bond.com
56
Chapter 7 contact way
Shenzhen Han-Bond Technology Co.,Ltd
Company address: China Shenzhen Baoan District Fuyong Street rainbow colorful
city Xiamen stone garden building B room 1306
Tel: 86-755-61508810
Fax:86-755-61508813
Quanjiao Han-Bond Technology Co.,ltd
Company address: Han-Bond Industrial Park,Yang Qiao Economic Development
Zone, Quan Jiao County, Chu Zhou City, Anhui Province, China , Zip Code
239500.
Tel: 86-550-5185755/655
Fax: 86-550-5185500
Company website: www.han-bond.com
Customer service Tel: 400-068-1698
Thank you for your selection of Han-Bond technology H8 plus vertical inkjet
cutting plotter all in one machine.
