VERTICAL BLINDS AND CONSERVATORY AWNINGS safe · …VERTICAL BLINDS AND CONSERVATORY AWNINGS...
Transcript of VERTICAL BLINDS AND CONSERVATORY AWNINGS safe · …VERTICAL BLINDS AND CONSERVATORY AWNINGS...
V E R T I C A L B LI N D S A N D CO N S E R VAT O RY A W N I N G S s a f e · t i m e l e s s · b e a u t i f u l
Form follows function – the timelessly modern conservatory awning with contrasting shapes – designed down to the last detail – optionally with tracfix system
markilux 8800 / 8800
www.markilux.com markilux
rated to wind resistance class 3
(corresponds to Beaufort 6)
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
180 | Special features w w w . m a r k i l u x . c o m
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
Design Features
the round cassette and angular guide tracks harmonise perfectly with one another and with the shapes found in contemporary conservatory design
when fully extended the rounded front profile sits flush with the end of the guide tracks, giving the system a completely closed appearance
when retracted the cover is protected from the weather by the cassette, which encloses it completely
for long-lasting attractiveness the awning has been powder coated
Technical Specification
exterior solar shading so the heat does not get into the conservatory in the first place
by virtue of the especially sturdy construction areas of up to 36m² can be covered safely by one unit with a single cover
permanently high cover tension is achieved by way of two special gas-piston mechanisms operating independently of one another
motor with electronic cut-off mech-anism to prevent overheating and damage if the awning is obstructed. (Not in the case of a radio-controlled motor)
brackets with patented clip-on mechanism for simple, problem free installation
Optional Accessories
radio-controlled motor with remote control for comfortable operation, markilux remote control with ergonomic design
wall sealing profile to cover the gap between awning and wall
tracfix system – attractive, completely closed appearance with no annoying gap between the blind cover and the tracks. When completely extended the front profile finishes flush with the end of the guide tracks
to simplify fixture, a broad selection of brackets is available
awning available in non-standard RAL colours
side viewface fixture
awning pitch from 5°—45°
front profile closes completely flush with the guide tracks
coupled unit2 fields
side viewfixture to a conservatory
the maintenance cover at each end of the cassette aids quick installation
side view wall sealing profile (optional) up to a maximum awning pitch of 15°
when the awning is retracted, the cover is fully protected within the cassette
units with tracfix (optional) have no gap between the cover and the guide track; when completely exten ded the front pro -file finishes flush withthe end of guide tracks
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Dimensions and configuration options | 181
MA MAmin.
150 200 250 300 350 400 450 500 550 600 6501) 7001)
43374—
150151—
200201—
250251—
300301—
350351—
400401—
450451—
500501—
550551—
600601—
650651—
700
H
150
60
[67]
70
[77]
200250300350 • •
4002) • • • • • • • • • • • •
4502) • • • • • • • • • •• •• ••
5002) • • • • • • • • •• •• •• —
5502) • • • • • • • •• •• •• — —
6002) • • • • • • •• •• •• •• — —
6502) • • • • • • •• •• •• — — —
7002) •• •• •• •• •• •• •• •• — — — —
Dimensions and configuration options
1) depending on the fixture combination, an additional central cassette support is required from a fixture width of 601 cm, and a central support for any cover support tube from a fixture width of 451 cm2) from an extension of 401 cm, an additional track bracket per track is required• 1 cover support tube•• 2 cover support tubes
= tracfix (optional)
standard optional
hard-wired motor —
radio-controlled motor (433 MHz) —
silentec —
io radio-controlled motor —
Operation / Drive unit
standard optional
traffic white RAL 9016
metallic aluminium RAL 9006
anthracite metallic RAL 5204
grey brown, similar to RAL 8019
non-standard powder-coated finish
Frame colours
Colours similar to those in the RAL chart. Colours may differ slightly from those depicted in both hue and finish.
Covers
3) not available in tracfix units
fabric range no. standard optional
sunsilk snc 324 xx / 328 xx / 369 xx —
sunvas snc 310 xx / 311 xx 313 xx — 315 xx —
sunsilk perla FR 374 xx — 4)
transolair 338 xx —perfotex 332 xx 3) —sunvas perla 370 xx — 4)
= hard-wired motor 433 = radio-controlled motor (433 MHz)
MA = fixture width / order widthMin. MA = minimum widthsH = extension
dimensions in cm[…] dimensions in the case of tracfix
4) only available in tracfix units; from a fixture width of 501 cm, maximum extension 450 cm
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
182 | Coupled units / Dimensions and tolerances / Miscellaneous / Additional information w w w . m a r k i l u x . c o m
standard optional
wall sealing profile — 2)
tracfix —
light and wind sensor —
Miscellaneous
width extension
housing tolerances + 5 / − 10 mm
awning cover width =fixture width − 90 1) mm
blind cover length = extension ± 0 mm
Dimensions and tolerances
1) dimensions for tracfix units on request
2) up to a maximum awning pitch of 15°
standard optional
2 fields —
3 fields —
Coupled unitsThe width of the awning cover is always less than that of the awning.
Fixture / order width definition: The fixture/order width is the measurement from track centre to track centre i.e. from fixture point to fixture point on the conservatory. The overall width of the awning is 100 mm greater than the fixture width. The fixture width tolerance is + 0 mm / – 20 mm.
Definition of the extension / order extension: The extension is measured with the awning extended from the back of the cassette to the leading edge of the front profile. The tolerance in the extension is + 40 / – 40 mm.
Definition of operating side: the operating side is always given as if seen from the outside (right or left).
In cases of face fixture the awning can be set at a pitch of between 5° and 45°. Track-only mounted awnings can be set at pitches of up to 90°.
Units which are to run uphill are available upon request.
N.B! If the motor is used continuously it will stop automatically after 3 to 4 minutes to prevent overheating.
N.B! In contrast to standard motors, radio-controlled motors have no safety cut-out mechanism if the front profile is obstructed. If this function is desired in combina-tion with radio-controlled operation, order the hard-wired motor with an external radio receiver and an appropriate transmitter.
In the case of a bank of awnings operating simultaneously, the same speed of rotation of the motors cannot be guaran-teed because of the internal tolerances of the motors.
The rate of extension of a single unit with hard-wired motor is approximately 11 seconds per metre.
Depending on the size of the awning, deflection may be in evidence in individual profiles and sections of profile which is completely unavoidable. This affects neither the functionality nor the durability of the awning.
Additional information
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Dimensions and configuration options | 183
Dimensions and configuration optionsCoupled unit, 2 fields, 1 or 2 motors
Coupled unit, 3 fields, 2 motors
MA
500 600 700 800 900 1000 1100 1200 1300 1400401—
500501—
600601—
700701—
800801—
900901—
10001001
—1100
1101—
12001201
—1300
1301—
1400
overall width + 10
H
150200250300350 • •
400 • • • • • • • • • •
450 • • • • • • • •• •• ••
500 • • • • • • •• •• •• —
550 • • • • • •• •• •• — —
600 • • • • •• •• •• •• — —
650 • • • • •• •• •• — — —
700 •• •• •• •• •• •• — — — —
MA
600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100551—
600601—
700701—
800801—
900901—
10001001
—1100
1101—
12001201
—1300
1301—
14001401
—1500
1501—
16001601
—1700
1701—
18001801
—1900
1901—
20002001
—2100
overall width + 10
H
150200250300350 • • •
400 • • • • • • • • • • • • • • • •
450 • • • • • • • • • • • •• •• •• •• ••
500 • • • • • • • • • • •• •• •• •• •• 2) —
550 • • • • • • • • •• •• •• •• •• — — —
600 • • • • • • • •• •• •• •• •• •• — — —
650 • • • • • • • •• •• •• •• •• 1) — — — —
700 •• •• •• •• •• •• •• •• •• •• — — — — — —
• 1 cover support tube
1) 2 cover support tubes; possible up to a max. fixture width of 1650 cm•• 2 cover support tubes
2) 2 cover support tubes; possible up to a max. fixture width of 1950 cm
= tracfix (optional)
dimensions in cm
dimensions in cm
MA = fixture width / order widthH = extension
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
184 | Additional information coupled units / Fixtures, fittings and accessories w w w . m a r k i l u x . c o m
Coupled conservatory awnings are available up to a max. width of 3 single units (3 fields) side by side.
In the case of coupled units with 2 or 3 fields and 2 motors unequal running speeds due to tolerances within the motors may occur.
In the case of coupled units with fields of differing sizes smooth rolling-up behaviour of the covers cannot be guaran-teed. This has no bearing on the functionality of the awning or the durability of the cover.
The matrices above assume equal field widths in coupled awnings. If a coupled unit of unequal field width is ordered, for which a cover support tube is required on the larger awning, then – if only for aesthetic reasons – one should also be fitted to the smaller awning (see the matrix for one field).
In the case of coupled units up to a fixture width of 700 cm the cassette will be supplied in one piece. If, for transportation or installation reasons, the cassette needs to be split, please note this explicitly when ordering.
Additional informationThe rate of extension of coupled units with 2 fields, 1 Motor and 3 fields, 2 motors is approximately 16 to 18 seconds per metre. In the case of coupled units with 2 fields, 2 motors extension takes as long as with single awnings i.e. approx. 12 to 14 seconds per metre.
In the case of 2 motors, the individual motors can be operated independently of one another.
For the maximum awning size, please refer to the matrix for single units!
If coupled awnings are fitted into a recess or reveal the over-all width of the coupled awning must be at least 6 cm less than the width of the opening to allow the awning to be coupled.
Depending on the size of the awning, deflection may be in evidence in individual profiles and sections of profile which is completely unavoidable. This affects neither the functionality nor the durability of the awning.
Cassette fixture brackets
Fixtures, fittings and accessories
top fixture bracket assembly
pitch adjustment range from 5°—45°
77058.
face fixture bracket assemblyleft
pitch adjustment range from 5°—45°
76063.
40 126
bottom fixture bracket assemblyfor track-only fixture
left
76061.
face fixture bracket assembly, wide, right
pitch adjustment range from 5°—45°
76232.
face fixture bracket assemblyright
pitch adjustment range from 5°—45°
76064.
40
126
bottom fixture bracket assembly for track-only fixture
right
76062.
face fixture bracket assembly, wide, left
pitch adjustment range from 5°—45°
76231.
cassette coupling bracket assemblyface fixturecentral
pitch adjustment range from 5°—45°
76181.
coupling bracket assemblyfor the cassettefor track-only fixture
bottom fixture coupling point
76180.
. = insert RAL colour code no.
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Fixtures, fittings and accessories | 185
Fixtures, fittings and accessories
storm safety bracket assembly for the cassette
(recommended in windy locations and as an addi-tional safety measure for the cassette)
76197.
227—
527
raised cassette bracket assemblyfoot can be tiltedbackwards by up to 45°, head of cassette fixture bracket can be tilted forwards by up to 45°left, for track-only fixture
76067.
wall sealing profile
available by the metre
for installation example please see “Face fixture with wall sealing profile”
77780.
38
132
100
cassette / housingsupport assemblyfor track-only fixture
height 100 mm
76183.
bracket assemblycover support tube
76019.
29
20
34diagonal tensioning kit
(2 wire tensioners, 1 tensioning wire)
71790.
227—
527
raised cassette bracket assembly foot can be tilted backwards by up to 45°, head of cassette fixture bracket can be tilted forwards by up to 45° right,for track-only fixture
76068.
30
44
40
angled bracket to preventdeflection of the cover support tube for bracket height 100 mmfor installation example see “Installation dimensions”
76065.
140
132
38
cassette / housingsupport assemblyfor track-only fixture
height 140 mm
76184.
coupling bracket assemblycover support tube
76059.
270
60 fixture bracket assembly for light, wind and rain sensor
76050.
227—
527
raised cassette bracket assembly foot can be tilted backwards by up to 45°, head of cassette fix-ture bracket can be tilted forwards by up to 45°for coupling pointbottom fixture
76198.
support bracket assembly to prevent deflection of the cover support tube, can be shortened to between 70—320 mm(with clamp plate), for installation example see “Installation dimensions”
71780.
coupling bracket assembly for the cassette in the case ofrigid track-only fixture
fixture types 31 and 32
76069.
storm safety clip / closing guide
76235.
. = insert RAL colour code no.
110
50
85
65 50
15
25
Ø9
angled adapter platefor rounded mullions
withoutfixture bolts
76098.
angled adapter platefor rounded mullionsL/R incl. fixture bolts required in addition to fixture combination 32
76099.
110
40
25
15
85 track bracket assembly
for fixture directly to conservatory mullions (14 mm)
76804.
40 85
110 25
26
track bracket assembly
for fixture directly to conservatory mullions (25 mm)
76805.
bottom fixture reveal
left
76077.
bottom fixture reveal
right
76078.
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
186 | Fixtures, fittings and accessories www.markilux.com
Track brackets
Fixtures, fittings and accessories
70 40
track bracket assembly for track fixture, rigid
refer also to the section “Installation dimensions”
76017.
9
85
40 110
double track bracket assemblywith adjustable head
height 100 mm
refer also to the section “Installation dimensions”
76191.
9
85 110
40 20
10
footprint dimensions of adjustabletrack bracket
9
85
40 110
double track bracket assemblywith adjustable head
height 140 mm
refer also to the section “Installation dimensions”
76192.
9
60
45
85
110
track bracket assembly with adjustable foot plate
height 100 mm
refer also to the section “Installation dimensions”
76199.
universal track bracket assembly
height 140—500 mm
refer also to the section “Installation dimensions”
76053.
vario-V bracket assembly for single track fixture
refer also to the section “Installation dimensions”
76052.
track bracket for bottom fixture
available by the metreundrilled
max. length 6 m
76013.
60
universal track bracket assembly
height 100 mm
refer also to the section “Installation dimensions”
76054.
9110 40
85 track bracket assembly with adjustable head
height 100 mm
refer also to the section “Installation dimensions”
76046.
track bracket assemblywith adjustable head
height 100—500 mm
refer also to the section “Installation dimensions”
76047.
10
110
20,5
40858,5
spacer platetrack bracket
110 × 40 × 10 mm
78570.
track bracket assembly with adjustable head and foot
height 200—500 mm
refer also to the section “Installation dimensions”
76045.
340
flat track bracket assemblyfor lateral track fixturewith adjustable head
refer also to the section “Installation dimensions”
76049.
9
40 110
track bracket assemblyfor conservatory transom fixture
height 100 mm
refer also to the section “Installation dimensions”
76055.
9110 40
85
track bracket assemblywith adjustable head
height 140 mm
refer also to the section “Installation dimensions”
76048.
double track bracket assemblywith adjustable head
height 100—500 mm
refer also to the section “Installation dimensions”
76193.
60
110
9
85
10
8,5
adjustable foot plate for track bracket assembly
78165.
double track bracket assembly with adjustable head and foot
height 200—500 mm
refer also to the section “Installation dimensions”
76194.
fixture plate
110 × 60 × 10 mm
78158.
. = insert RAL colour code no.
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Fixture combinations | 187
Fixture combinations
Individual bracket combinations – see “Fixtures, fittings and accessories”.Please note the minimum quantity required for the width and unit height you intend to order!
All brackets incur a surchargeFixture combination 11 76061.L
76062.R 76017.
• an additional cassette support is required from a field width of 601 cm, 76183.
• from an extension of 401 cm an additional bracket 76017. per guide track is required
Fixture combination 12
76063. L76064. R
76046.
• only up to an extension of 400 cm• from an extension of 401 cm fixture combination 51• an additional cassette bracket is required from a fixture width of 601 cm,
76063.
Fixture combination 14 76046.
76061.L76062.R76180.
• an additional cassette support is required from a field width of 601 cm, 76183.
• from an extension of 401 cm an additional bracket 76046. per guide track is required
Fixture combination 16 76077. L
76078. R76180.76183.
76054.76046. • an additional cassette support is required from a field width of 601 cm,
76183.• from an extension of 401 cm an additional bracket 76046. / 76054. per guide
track is required
Fixture combination 21 76061.L
76062.R76180.
76049.
• an additional cassette support is required from a field width of 601 cm, 76183.
• from an extension of 401 cm an additional bracket 76049. per guide track is required
Fixture combination 22
76049.
76063.L76064.R76181.
• an additional cassette bracket is required from a fixture width of 601 cm, 76063.
• from an extension of 401 cm an additional bracket 76049. per guide track is required
Fixture combination 31 76017. 76017.
• an additional cassette support is required from a field width of 601 cm, 76183.
• from an extension of 401 cm an additional bracket 76017. per guide track is required
Fixture combination 32 76046.76046.
• an additional cassette support is required from a field width of 601 cm, 76183.
• from an extension of 401 cm an additional bracket 76046. per guide track is required
Fixture combination 41 76063.L
76064.R76181.
76052.
• an additional cassette bracket is required from a fixture width of 601 cm, 76063.
• from an extension of 401 cm an additional bracket 76052. per guide track is required
Fixture combination 51
76046.76052.
76063.L76064.R76181.
• up to an extension of 400 cm, fixture type 12• an additional cassette bracket is required from a fixture width of 601 cm,
76063.
Fixture combination 61
76046.
76067.L76068.R76198.
• an additional cassette bracket is required from a fixture width of 601 cm, 76067.
• from an extension of 401 cm, fixture type 81
Fixture combination 71
76067.L76068.R76198. 76052.
• an additional cassette bracket is required from a fixture width of 601 cm, 76067.
• from an extension of 401 cm an additional bracket 76052. per guide track is required
• diagonal tensioners are recommended
Fixture combination 81
76067.L76068.R76198. 76046.
76052.
• up to an extension of 400 cm, fixture type 61• an additional cassette bracket is required from a fixture width of 601 cm,
76067.• diagonal tensioners are recommended
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
[17]
20
60
45 MB = 300
60
[17]
20
45 MB = 300
MA = BA
M
185
H
1
50
50 50
= MB
M
DIF
H +
DIF
45 MB = 300
MA = BA
M
50
M
188 | Installation dimensions w w w . m a r k i l u x . c o m
Single unit 1 field, 1 motor asymmetrical guide track lengths
Coupled unit 2 fields, 1 motor
Installation dimensions
MHBAMBDIF
MA[…]
M
=====
==
=
overall awning width MA + 100 mmextensionwidth between fixture pointsbracket fixture rangedifference in measurement
awning width between fixture points = fixture width = order widthdimensions of the cover gap in a standard unit, no cover gap in units with tracfix systemmotor
MA = BA
[17]
[17]
[17]
20
116 60
45 MB = 300 45 MB = 300
MA = BA
M
60
185
20
[17]
H
50 50
= MB
M
MB = 150
dimensions in mm
dimensions in mm
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Installation dimensions | 189
Coupled unit, 2 fields, 2 motors
Coupled unit, 2 fields, 2 motors, asymmetrical extensions
Installation dimensions
MHH1H2MB
BAMA[…]
M
=====
===
=
overall awning widthextensionlong extensionshort extensionbracket fixture range
width between fixture points awning width between fixture points = fixture width = order widthdimensions of the cover gap in a standard unit, no cover gap in units with tracfix systemmotor
MA = BA
[17]
[17]
[17]
20
116 60
45 MB = 300 45 MB = 300
MA = BA
M
60
185
20
[17]
H
50 50
= MB
MM
MB = 150
[17]
[17]
116
MB = 300 45 MB = 300
M
60
185
20
[17] H1 H
2
[17]
MA = BA 50 MA = BA
45
60 = MB
MM
50
20
MB = 150
dimensions in mm
dimensions in mm
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
MA = BA
EA KA
MA = BA MA = BA
H
60
[17] [17]
185
[17] [17] [17]
[17]
20
116 116 60
20
45 MB = 300 45 MB = 300
M
50 50
= MB
M M
MB = 150 MB = 150
MA = BA
EA KA
MA = BA MA = BA
H
60
[17] [17]
185
[17] [17] [17]
[17]
20
116 116 60
20
45 MB = 300 45 MB = 300
M
50 50
= MB
M M M
MB = 150 MB = 150
76046.
BT
76046.
BT
190 | Installation dimensions w w w . m a r k i l u x . c o m
Coupled unit, 3 fields, 2 motors
Detailed illustration of guide tracks
Installation dimensions
MEAKAHBAM
76046.BT[…]
MBMA
======
===
==
overall awning widthsingle unitcoupled unitextensionwidth between fixture points motor
track bracket with adjustable headmullion / fixture substratedimensions of the cover gap in a standard unit, no cover gap in units with tracfix systembracket fixture rangeawning width between fixture points = fixture width = order width
dimensions in mm
dimensions in mm
dimensions in mm
Coupled unit, 3 fields, 3 motors
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Installation dimensions | 191
Fixture combination 11, bottom fixture
Fixture combination 14, bottom fixture
Installation dimensions
MHBA76062.76180.
S
76061.
MA76017.
76046.
=====
=
=
==
=
overall awning widthextensionwidth between fixture points bottom cassette fixture bracket, rightcoupling bracket for bottom cassette fixturein cross section
bottom fixture cassette bracket, left, from a fixture width of 6001 mman additional housing support is required, 76183.awning width between fixture points = fixture width = order widthtrack bracket for track-only fixture, rigid up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per tracktrack bracket, with adjustable head, 100 mm up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per track
208
2
1
105
70
116
37
84
210 H
min. 100max. 1000
30
MA
BA
60
50
187
M
76061.76062.76183.
76017.
A
AS A-A
37
208
105
60 116
187
210
21
min. 100max. 1000
H
84
50 MA
BA
30
A
A
76046.
76061.76062.76183.
S A-AM
dimensions in mm
dimensions in mm
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
105
max. 67
min. 46 min. 46
max. 67 MA
MA
max. 73
min. 36 min. 36
max. 73
MA
MA
min. 17 MA min. 17
max. 20
MA
max. 20
S A—A
A
A
V1
V2
V3
76061.76062.76183.
76049.
192 | Installation dimensions w w w . m a r k i l u x . c o m
Fixture combination 21, for track-only fixture (from a field width of 6001 mm an additional housing support is required in the centre)
Installation dimensions
dimensions in mmMHBAMAS76061.76062.76180.76017.76046.
==========
overall awning widthextensionwidth between fixture points awning width between fixture points = fixture width = order widthin cross sectionbottom fixture bracket, an additional cassette support is required from a field width of 6001 mm, 76183.bottom cassette fixture bracket, rightcoupling bracket for bottom cassette fixturerigid track bracket for track-only fixture, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per tracktrack bracket with adjustable head 100 mm, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per track
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Installation dimensions | 193
Fixture type 12, face fixture for extensions up to 4000 mm, from an extension of 4001 mm fixture type 51
Fixture type 22, face fixture with lateral flat track bracket
Installation dimensions
37
116 60
70
105
H
210
187
1
6 2
04
84
AX
MA
30
50
BA
min. 100max. 1000
A
A
S A-A
76063.76064.76181.
76046.
M
W
37
50 50 MA
BA
M min. 100max. 1000
max
. 385
H
210
16
187
203
AX
84
76049.
76063.76064.76181.
S A-A
A
A
W
dimensions in mm
WMHBASAX76181.MA
76063.
76064.76046.
76049.
========
=
==
=
pitchoverall awning widthextensionwidth between fixture points in cross sectiondistance from cassette to wallcassette coupling bracket, face fixtureawning width between fixture points =fixture width = order widthface fixture bracket, left, from a fixture width of 6001 mm an additional face fixture bracket is required, 76064.face fixture bracket, right, from a fixture width of 6001 mm an additional face fixture bracket is required, 76064.track bracket with adjustable head 100 mm, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, fixture type 51flat bracket for lateral track fixture with adjustable head, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per track
W AX
5° 26
10° 32
15° 37
20° 43
25° 47
30° 50
35° 52
40° 53
45° 53
W AX
5° 26
10° 32
15° 37
20° 43
25° 47
30° 50
35° 52
40° 53
45° 53
dimensions in mm
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
194 | Installation dimensions w w w . m a r k i l u x . c o m
Fixture combination 31, for track-only fixture (from a field width of 6001 mm an additional housing support is required in the centre)
Fixture combination 32, for track-only fixture (from a field width of 6001 mm an additional housing support is required in the centre)
Installation dimensions
105
37
116
70
60
187
84
210 H
MA 50
30
BA
min. 300max. 400
min. 100max. 1000
76017.
76017.
S A-A
A
A
M
37
105
208
116
70
60
210 H
187
84
21
min. 100max. 1000
30
50 MA
BA
76046.
76046.
M
S A-A
A
Amin. 300
max. 400
dimensions in mm
dimensions in mmBAMHMAS76017.76046.
=======
width between fixture points overall awning widthextensionawning width between fixture points = fixture width = order widthin cross sectionrigid track bracket for track-only fixture, up to an extension of 4000 mm, 2 per track, from an extension of 4001 mm, 3 per tracktrack bracket with adjustable head 100 mm, up to an extension of 4000 mm, 2 per track, from an extension of 4001 mm, 3 per track
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
dimensions in mm
w w w . m a r k i l u x . c o m Installation dimensions | 195
Fixture type 41, face fixture with vario-V brackets
Fixture type 51, face fixture for extensions greater than 4000 mm, up to an extension of 4000 mm fixture type 12
Installation dimensions
min
. 105
max
. 300
258
37
116
70
60
min. 300max. 1000
210 H
100
16
203
1
87
50 MA
BA
30
76063.76064.76181.
M
S A-A
A
A
76052.
AX
W
258
116 60
37
187
1
6 2
03
210
min. 100max. 1000
30
50 MA
H
BA
AX
76046.
76063.76064.76181.
M
S A-A
A
A
W
dimensions in mm
W AX
5° 26
10° 32
15° 37
20° 43
25° 47
30° 50
35° 52
40° 53
45° 53
W AX
5° 26
10° 32
15° 37
20° 43
25° 47
30° 50
35° 52
40° 53
45° 53
WAXMHBASMA
76046.
76052.76063.76064.76181.
=======
=
====
pitchdistance from cassette to walloverall awning widthextensionwidth between fixture points in cross sectionawning width between fixture points = fixture width = order widthtrack bracket with adjustable head 100 mm, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per trackvario-V brackets for lateral track fixture, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per trackface fixture bracket, left, from a fixture width of 6001 mm an additional face fixture bracket is required, 76064.face fixture bracket, right, from a fixture width of 6001 mm an additional face fixture bracket is required, 76064.cassette coupling bracket, face fixture
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
196 | Installation dimensions w w w . m a r k i l u x . c o m
Fixture combination 32 with “angled adapter plate for rounded mullions incl. fixture bolts” (76099.)
Installation dimensions
BC 75 75
25 25
MA
M
76099.
A – A
105
7
0
MA
M
50
M 50 MA 50 50 50 50
BC BC
M MA MA 50 50
31 31
19
69 69
19 19 19
105
7
0
105
7
0
76099. 76099.
A – A A – A
125
105
7
0
76606.
76099.
125
125
2
28
187
min. 100max. 1000
H
A
min. 300max. 400
A76099.
125
1
05
V2 V3
125
V1
BC 75 75
25 25
MA
M
76099.
A – A
105
7
0
MA
M
50
M 50 MA 50 50 50 50
BC BC
M MA MA 50 50
31 31
19
69 69
19 19 19 1
05
70
105
7
0
76099. 76099.
A – A A – A
125
105
7
0
76606.
76099.
125
125
2
28
187
min. 100max. 1000
H
A
min. 300max. 400
A76099.
125
1
05
V2 V3
125
V1
BC 75 75
25 25
MA
M
76099.
A – A
105
7
0
MA
M
50
M 50 MA 50 50 50 50
BC BC
M MA MA 50 50
31 31
19
69 69
19 19 19
105
7
0
105
7
0
76099. 76099.
A – A A – A
125
105
7
0
76606.
76099.
125
125
2
28
187
min. 100max. 1000
H
A
min. 300max. 400
A76099.
125
1
05
V2 V3
125
V1
MMAA—ABCH76099.V1, V2 xx.
=======
overall awning widthawning fixture width = order widthin cross sectionawning width between fixture pointsextensionangled adapter plate for rounded mullions incl. fixture boltsvariation 1, 2 xx.
dimensions in mm
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
15
25
7,5
25
76804.
4
26
40
85
Ø 10
110
85
76804.76805.
76805.
w w w . m a r k i l u x . c o m Installation dimensions | 197
dimensions in mm
Installation dimensions 76804. / 76805.
110
40
25
15
85 track bracket assembly
for fixture directly to conservatory mullions (14 mm)
76804.
40 85
110 25
26
track bracket assembly
for fixture directly to conservatory mullions (25 mm)
76805.
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
198 | Installation dimensions w w w . m a r k i l u x . c o m
Fixture type 61, raised bottom cassette fixture
Fixture type 71, raised bottom fixture with vario-V brackets
Installation dimensions
min
. 227
max
. 527
37 4
5 4
5
50 50 MA MA M
BA BA
210
H
min. 100max. 1000
187
76046.
76067. 76068.76198.
B
A
S A—B
37
min
. 227
max
. 527
258
187 210
H
MA MA 50 50 M
BA BA
min. 400max. 800
45
45
S A—A
A
76067. 76198. 76068.
A
dimensions in mm
dimensions in mm
MHBASMA76046.76052.76067.76068.76198.
==========
overall awning widthextensionwidth between fixture points in cross sectionawning width between fixture points = fixture width = order widthtrack bracket with adjustable head 100 mm, up to an extension of 4000 mm, from an extension of 4001 mm fixture type 81vario-V brackets for lateral track fixture, up to an extension of 4000 mm, 1 per track, from an extension of 4001 mm, 2 per trackraised cassette fixture bracket, left, an additional cassette bracket is required from a fixture width of 6001 mm, 76068. raised cassette fixture bracket, right, an additional cassette bracket is required from a fixture width of 6001 mm, 76068.raised cassette bracket, coupling point
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
37
45
45
258
min
. 227
max
. 527
210 187
H
105
min. 100max. 1000
50 50 MAMAM
BA BA
76067.
S A—B
A
B
76198. 76068.
76052.
76046.
w w w . m a r k i l u x . c o m Installation dimensions | 199
Fixture type 81, raised bottom cassette fixture for awnings with an extension greater than 4000 mm using vario-V brackets
Raised bottom fixture using cassette coupling bracket
Installation dimensions
76198.
dimensions in mm
dimensions in mm
MHBASMA76046.76052.76067.76068.76198.
==========
overall awning widthextensionwidth between fixture points in cross sectionawning width between fixture points = fixture width = order widthtrack bracket, with adjustable head, 100 mmvario-V bracket, for track fixtureraised cassette fixture bracket, left, an additional cassette bracket is required from a fixture width of 6001 mm, 76068. raised cassette fixture bracket, right, an additional cassette bracket is required from a fixture width of 6001 mm, 76068.raised cassette bracket, coupling point
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
200 | Installation dimensions w w w . m a r k i l u x . c o m
Diagonal tensioning kit for raised bottom fixture
Face fixture using cassette coupling bracket
Installation dimensions
BA BA
MA MA
M
76045. 76045. 76045.
71790.
50
71790.
71790. 71790.
71790. 71790.
71790. 71790.
50
dimensions in mm
dimensions in mmMBAMA76045.76181.71790.
======
overall awning widthwidth between fixture points awning width between fixture points = fixture width = order widthtrack bracket with adjustable head and foot 200 mm to 500 mmcassette coupling bracket, face fixturediagonal tensioning kit
Measurement from the back of the cassette to the leading edge of the front profile
76181.
86
70
187
H 210 AGEG
287
M
150
MA
EG AG
EGAG
==
awning retractedawning extended
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Installation dimensions | 201
Support bracket to prevent deflection of the cover support tube (100 mm)
Support bracket to prevent deflection of the cover support tube, can be shortened to between 70 mm and 320 mm
Installation dimensions
71780.76019.76059.76065.
====
support to prevent deflection of the cover support tube, can be shortened to between 70 mm and 320 mm (with clamp plate)bracket for cover support tubecoupling bracket for cover support tubeangled support bracket, 100 mm
105
Ø 48
30
40
6,5
7
1,5
21,8
76019.76059.
76065.
76065.
61
min
. 70
max
. 320
min
. 131
max
. 381
70
20
M12
6,6 11
12
50
6,4
71780.
A
A
B
B
76019.76059.
48
B-B
A-A
dimensions in mm
dimensions in mm
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
202 | Installation dimensions / Cable exit point w w w . m a r k i l u x . c o m
Installation dimensions double track bracket
Cable exit point in the case of motor-driven units
Installation dimensions
100
HH
MA = BA MA = BA
M M
45 MB = 300 45 MB = 300 HT
180
8 130 5826
dimensions in mm
dimensions in mm
HT 76191. 76192. 76193. 76194.
HH 105 145 105 to 505 205 to 505
MBAMAHTHHMB76191.76192.76193.76194.
==========
overall awning widthwidth between fixture points awning width between fixture points = fixture width = order widthfixture bracketfixture bracket heightbracket fixture range (cassette brackets)double track bracket assembly with adjustable headdouble track bracket assembly with adjustable headdouble track bracket assembly with adjustable headdouble track bracket assembly with adjustable head and foot
V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S markilux 8800 / 8800 tracfix
15
14
13
12
11
10
09
08
07
06
05
04
02
01
21
20
19
18
17
03
16
w w w . m a r k i l u x . c o m Anbringungsmaße | 203
Anbringungsmaße
WS
H
min. 100max. 1000
W
A
A
ZX
XX
AX
76063.76064.
Maße in mm
HWSWAAXXXZX76063.76064.
=========
extensiondistance from wall to center of support postinclination angledetailed viewdistance from cassette to walldistance upper edge bracket —cassettedistance upper edge cassette—guide trackface fixture bracket assembly, left, pitch adjustment range from 5°—45°face fixture bracket assembly, right, pitch adjustment range from 5°—45°
W AX XX ZX
5° 26 49 112
10° 32 38 120
15° 38 30 128
20° 44 22 135
25° 49 13 142
30° 54 4 149
35° 58 − 5 156
40° 62 − 15 161
45° 65 − 24 167
Fixture type 12, adjustable face fixture and adjustable track bracket assembly
markilux 8800 / 8800 tracfix V E R T I C A L B L I N D S A N D C O N S E R V A T O R Y A W N I N G S
21
20
05
19
17
01
02
03
04
06
07
08
09
10
11
12
13
14
15
18
16
Fixture combination 16,
37
208
105
116 60
187
210
21
min. 100max. 1000
H
84
BA
MA
A
A
76054.
76077.76078.76180. / 76183.
A–A
M
76046.
25
BAHMMA
76046.
76054.76077.76078.76180.
76183.
====
=
====
=
width between fixture pointsextensionoverall awning widthawning width between fixture points = M − 100 mm
track bracket assembly with adjustable head, height 100 mmuniversal track bracket assembly, height 100 mmbottom fixture reveal, leftbottom fixture reveal, rightcoupling bracket assembly for the cassette for track-only fixture, bottom fixture coupling pointcassette / housing support assembly for track-only fixture, height 100 mm
dimensions in mm
204 | Installation dimensions w w w . m a r k i l u x . c o m
Installation dimensions