Version: C01 - EVOC · Chapter 1 Product Introduction IPC-6805E - 1 - Chapter 1 Product...
Transcript of Version: C01 - EVOC · Chapter 1 Product Introduction IPC-6805E - 1 - Chapter 1 Product...
IPC-6805E
壁挂式兼容机箱
Compatible Wall Mount Chassis
Version: C01
Copyright Notice
Information offered in this manual is believed to be correct at the time of printing, and
is subject to change without prior notice in order to improve reliability, design and
function and does not represent a commitment on the part of the manufacturer. In no
event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of improper installation and/or use, or inability to
use the product or documentation.
This user manual is protected by copyright. No part of this manual may be reproduced,
stored in any retrieval system, or transmitted, in any form or by any means,
mechanical, electronic, photocopied, recorded or otherwise, without the prior written
permission from the manufacturer.
Trademarks
EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. Other
product names mentioned herein are used for identification purposes only and may be
trademark and/or registered trademarks of their respective companies.
Please visit our website: http://www.evoc.com for more information,
or send an email to the Technical Support Mailbox [email protected]
(International) or [email protected] (Domestic) for consultation.
Hotline: 4008809666
Safety Instructions
1. Please read this manual carefully before using the product;
2. Before inserting, removing or re-configuring motherboards or expansion cards,
first disconnect the computer and peripherals from their power sources to
prevent electric shock to human bodies or damage to the product;
3. Before moving the product, please unplug the AC cable from the power socket;
4. When inserting or removing boards, please firstly unplug the AC power cable;
5. Before connecting or disconnecting any signal cable, make sure all power cables
are unplugged in advance;
6. After turning off the computer, wait at least 30 seconds before turning it back
on;
7. All the operations such as upgrade, remove or installation shall be implemented
on the ESD worktable, because some exactitude components are sensitive to
electrostatic discharge (ESD).
8. If there's no ESD worktable, please take the following measures to prevent
damage from electrostatic discharge (ESD):
a) Wear a antistatic wrist strap and connect it with the metal part of the
corresponding product;
b) Always touch the metal enclosure or frame before touching any
components;
c) Keep part of your body in contact with the metal enclosure to discharge the
static while handling components;
d) Avoid unnecessary movement;
e) Hold the components (especially the boards) by the edges;
f) Place the components on a grounded, static-free operating platform. Use a
conductive foam pad if available (not the component wrapper).
g) Do not let the components slide on the operating platform.
9. Use cross-head screwdriver to operate. A magnetic screwdriver is recommended
(Magnet helps to prevent screws from remaining in the enclosure). Do not leave
any tools or accessories inside the enclosure;
10. Ensure abundant cooling and ventilation.
11. Non-professional personnel are not allowed to open the enclosure.
Contents
Chapter 1 Product Introduction.....................................................................................1
Overview .............................................................................................................1
Main Functions....................................................................................................1
Power Feature......................................................................................................2
Main Performance ...............................................................................................2
Mounting Mode...................................................................................................3
Requirements of Transportation and Storage.......................................................3
Chapter 2 Installation....................................................................................................5
Product Outline....................................................................................................5
Product Appearance and Installation Dimensions ...............................................5
External Connectors ............................................................................................6
Overall Assembly Drawing .................................................................................7
Installing the Cover .............................................................................................8
Installing and Removing the Motherboard ..........................................................8
Installing the Drivers ...........................................................................................9
Installing the Power...........................................................................................11
Installing the Fan ...............................................................................................13
Installing the Dust-proof Net .............................................................................14
Installing the Foot Pad.......................................................................................14
Installing the Wall-mounted Bar........................................................................15
Chapter 3 Installing the Drivers..................................................................................17
Chapter 1 Product Introduction
IPC-6805E - 1 -
Chapter 1 Product Introduction
Overview
IPC-6805E, a wall-mounted chassis compatible with EPX series products, is based on
the patented technologies of our FSC full-size cards and the EVOC-EPX bus. The
chassis is developed considering the fact that the EPX products are being sold without
auxiliary EPX bus products and certain market needs are not met. The chassis is
compatible with various EVOC motherboards, such as FSC, EPI, EPE and Mico ITX,
etc.
Main Functions
Connectors and Buttons on the Chassis
Two front-accessible USB 2.0 ports, ATX rocker switch, reset switch, power supply,
HDD indicator and safe door with lock.
Expandability
Supported motherboards: PICMG 1.0, PICMG 1.3, EPI 2.0 and EPE standard full-size
boards and EC7 standard single boards;
Supported carrier boards: 6-slot standard PICMG 1.0 carrier, 5-slot standard PICMG
1.3 carrier, 4/5-slot standard EPI 2.0 carrier and 4-slot EPE carrier.
Supported power supplies: standard PS2 ATX power, standard PS2 AT power, Mini
redundant power, 1U power (EC7 motherboard).
Storage Expansion
One notebook super-slim DVD-ROM and one 3.5″ HDD bay;
One notebook super-slim DVD-ROM and one 2.5″ HDD bay (adopting redundant
power);
Chapter 1 Product Introduction
- 2 - IPC-6805E
Power Feature
Input Voltage/Frequency: 220VAC/50Hz;
Power Consumption of the PC:
1. When mated with FSC-1813L2NA+ PCI-6106E3: 46W (Standby); Power
Consumption of the PC: 58.2W (MaxPower 100%);
2. When mated with EPE-1814V2NAR+ EPE-6105E2: 26.8W (Standby); Power
Consumption of the PC: 91.8W (MaxPower 100%);
Note: the power consumption varies with different boards used together with the PC.
Main Performance
Mechanical Dimensions, Weight and Environment
Dimensions: 397mm (L) x 174mm (W) x 265mm (H);
Net Weight:
1. Net weight when the PC is mated with PCI-6106E3: 8.35Kg;
2. Net weight when the PC is mated with EPE-6105E2: 10.35Kg
Note: the net weight varies with different boards used together with the PC.
Operating Environment:
Temperature: 0°C ~ 50°C;
Humidity: 5% ~ 90% (non-condensing);
Storage Environment:
Temperature: -20°C ~ 60°C;
Humidity: 5% ~ 90% (non-condensing).
EMC
Radiation disturbance is compliant with GB9254-2008, class A;
Conducted susceptibility meets the threshold of GB/T 17618-2008;
Chapter 1 Product Introduction
IPC-6805E - 3 -
Reliability
MTBF≥50000h;
MTTR≤0.5h.
Safety
Meets the basic requirements of GB4943;
Mechanical and Environment Adaptability
Anti-vibration: 5 ~ 19Hz/1.0mm amplitude; 19 ~ 200Hz/1.0g acceleration;
Anti-shock: 10g acceleration, 11ms duration;
Mounting Mode
□19″ Rack Mount □Desktop □Embedded Panel
■Wall Mount □VESA Standard Arm □Portable
□Others___________
Requirements of Transportation and Storage
Transportation
Well-packaged products are suited for transportation by truck, ship, and plane. During
transportation, products should not be put in open cabin or carriage. During
transshipping, products should not be stored in open air without protection from the
atmospheric conditions. Products should not be transported together with inflammable,
explosive and corrosive substances and are not allowed to be exposed to rain, snow
and liquid substances and mechanical force.
Chapter 1 Product Introduction
- 4 - IPC-6805E
Storage
Products should be stored in package box when it is not used. And warehouse
temperature should be 0°C ~ 40°C, and relative humidity should be 20% ~ 85%. In
the warehouse, there should be no harmful gas, inflammable, explosive products, and
corrosive chemical products, and strong mechanical vibration, shock and strong
magnetic field interference. The package box should be at least 10cm above ground,
and 50cm away from wall, thermal source, window and air inlet.
Chapter 2 Installation
IPC-6805E - 5 -
Chapter 2 Installation
Product Outline
Product Appearance and Installation Dimensions
Unit: mm
Chapter 2 Installation
- 6 - IPC-6805E
External Connectors
Front Panel
Rear Panel A
Rear Panel B
Chapter 2 Installation
IPC-6805E - 7 -
Overall Assembly Drawing
1 Cover 2 Mid Batten 3 DVD-ROM Bracket
4 USB 5 Door 6 Lock
7 Hinge 8 LED Board 9 Power Switch
10 Front Cover for the Dust-proof Net
11 Front Batten 12 Chassis
13 Mounting Bar 14 Rear Cover 15 Rear Batten
16 PS2 Power Bracket 17 Adjustable Batten 18 Power
Chapter 2 Installation
- 8 - IPC-6805E
Installing the Cover
Loosen the two captive screws by hands and then pull the cover backward to open it.
Installing and Removing the Motherboard
Installing the Motherboard:
1, Loosen the captive screws by hands to open the cover;
2, Remove the front, mid and rear battens respectively and then install the
Chapter 2 Installation
IPC-6805E - 9 -
rubber spring pads. Please adjust the location of the pads according to
different motherboards.
3, Take off the slot cover of the motherboard slot enclosed with the chassis;
4, Insert the motherboard and fasten the screws on the slot cover.
Removing the Motherboard:
1, Install the front, mid and rear battens on the chassis respectively and
tighten the screws. Please check whether the PCB has been buckled by the
spring pad.
2, Put on the cover and fasten the captive screws.
Installing the Drivers
A. Hard Disk Installation:
Chapter 2 Installation
- 10 - IPC-6805E
1, Fix the hard disk with the left and right bracket of the hard disk and tighten
the screws (pay attention to the location of the bracket of the hard disk);
2, Assemble the well-assembled hard disk with the four shock absorption
pads with oil bag on the HDD main bracket and then tighten the screws;
3, Fix the shroud plate on the main bracket and tighten the screws;
4, Install the well-assembled HDD module into the chassis and fix it with four
screws (1, 2, 3 and 4) on the side wall.
B. DVD-ROM Installation:
Chapter 2 Installation
IPC-6805E - 11 -
1, A: remove the screws (1, 2 and 3) fixing the baffle on the slot of the DVD-ROM;
2, B: fix the DVD-ROM on the DVD-ROM bracket by four M2 screws and then
tighten the four screws;
3, C: install the well-assembled DVD-ROM into the chassis by screws (1, 2, 3 and
4) and then tighten the screws.
Installing the Power
A: PS2 Power
Chapter 2 Installation
- 12 - IPC-6805E
1, Lay the power into the chassis, insert four screws (1, 2, 3 and 4 BS screws) into
the corresponding holes between the power and the rear baffle and then tighten
the screws.
2, Align the holes on the power bracket with that on the side wall of the chassis,
insert and tighten the two screws (5 and 6 truss head screws).
B: Exclusive Mini-type Redundant Power (Size: 185*150*86)
1, Fix the rear bracket and the side bracket enclosed with the redundant power with
the redundant power by enclosed screws and fasten them;
2, Lay the redundant power into the chassis (please remove the PS2 power bracket
before installing the redundant power);
3, Fix the power with the rear baffle (5, 6, 7 and 8 BS screws);
4, Align the rear bracket of the power with the rivets on the side wall of the chassis
and then tighten the screws (1 and 2 truss head screws).
Chapter 2 Installation
IPC-6805E - 13 -
C: 1U Power
1, Lay the 1U power into the chassis, insert four screws (3, 4, 5 and 6 BS screws)
into the holes between the power and the rear baffle and tighten the screws;
2, Align the holes on the power bracket with that on the side wall of the chassis,
insert and tighten the two screws (1 and 2 truss head screws).
Installing the Fan
Remove the cover and the bracket of the filter net to replace the fan.
Chapter 2 Installation
- 14 - IPC-6805E
Installing the Dust-proof Net
Remove the counter sunk head screws 1, 2, 3 and 4 to replace the sponge filter net.
Installing the Foot Pad
The foot pads are accessories; users may install them according to requirements. The
foot pads share the truss head screws with the wall-mounted bars.
Chapter 2 Installation
IPC-6805E - 15 -
Installing the Wall-mounted Bar
The wall-mounted bars are accessories; users may install them according to
requirements. The bars share the truss head screws with the foot pads.
Vertical Dimension for the Wall-mounted Bracket of the PC
Chapter 2 Installation
Horizontal Dimension for the Wall-mounted Bracket of the PC
- 16 - IPC-6805E
第三章 驱动程序安装说明
IPC-6805E - 17 -
Chapter 3 Installing the Drivers
Regarding the installation of the driver program and the detailed information of the
motherboard, please refer to the enclosed CD of the PC.