Vancouver Door Company Catalogue 2012
-
Upload
sean-nixon -
Category
Documents
-
view
220 -
download
0
description
Transcript of Vancouver Door Company Catalogue 2012
Top and Bottom Horizontal Edge: 1-1/8” minimum solid wood or structural composite lumber, one piece,
laminated or LVL.
Vertical Edge: 1-1/2” minimum hardwood; solid, laminated veneered. Backer or inner ply may be struc-
tural composite lumber or LVL.
Solid Core 520P / 530P - Particleboard core (PC) 5 & 7-Ply
Hardwood Veneer / MDO / HDF
Core: Particle board, ANSI A208, 1, grade LD-1 or LD-2.
Core/Edge Interface: Stiles and rails high frequency bonded to core and core assembly sanded prior to
application of cross band and veneer.
Crossband: 2 ply edge glued hardwood or one piece HDF. (2-ply shown)
Faces: Selected hardwoods minimum 1/50”, Grades “A” , “AA” and high pressure laminate, medium den-
sity overlay or hardboard. High pressure laminate
0.050” direct to core, 0.050” with cross band or 0.125”.
Warranty: Lifetime for interior use / one year exterior, fully type 1 wood or MDO faces only.
Fire Ratings
• Thicknesses of 1-3/8” to 2-1/4”.
• Fire rating to 20 minute - Neutral & Positive Pressure, See Page 4 & 9 for requirements and options.
• STC rating = 32 (Flush & Glazed). May require additional gasketing / seals.
• LEED Credits, See page 11.
• Carb 1 & 2 compliant components.
• Lead lined or electro shielding. (See page 5)
• Vision lite and louver cutouts with matching flush or raised lip stop. Metal Vision panels or louvers supplied upon re-
quest. (See page 7)
• Applied moldings of any configuration,
profile and species. (See page 8)
• Quirks, grooves and inlays. (See page 7)
• Dutch cut with matching shelf (See page 7).
• Wicket door (inset to primary door see page 7).
• 2 or 4 panel Bifold units. (See page 6)
Page 3 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
High Pressure Decorative Laminate—HPDL
WDMA: PC-7 / AWS: PC-7 WDMA: PC-HPDL-3/5 / AWS: PC-5 PC-HPDL-3/5
Blocking Options: 5” (or as specified) top and/or bottom rail(s). For undercutting and specialized hardware. Must be specified if required.
Available Options for 520P
Fire Rated Mineral Core Doors, 745, 760 & 790.
FIRE DOORS 760 & 790 Mineral Core, 60 & 90 Minute Rated, See page 10.
WDMA: FD-7 FD-5 AWS: FD-7 FD-5 WDMA: FD-HPDL AWS:FD-HPDL-5
Top and Bottom Horizontal Edge: 1” GP Firestop I See Positive Pressure compliance for all ratings at
bottom of page.
Vertical Edge: GP Fire stop 1 or II with laminated hardwood. See note 1 at bottom of this page.
Additional material may be required.
Core: Georgia Pacific (proprietary) Mineral core .
Core/Edge Interface: Stiles and rails high fre-quency bonded to core and core assembly sanded
prior to application of crossband and veneer.
Vertical Edge: GP Fire stop II + I with laminated hardwood. See note 1 and bottom of this page.
Additional material may be required.
Top and Bottom Horizontal edge: 1-1/2” GP Fire stop II+I. See Positive Prressure compliance for all
ratings at bottom of page.
Crossband: 2 ply edge glued hardwood or One piece HDF (One piece HDF shown)
Faces: Selected hardwoods minimum 1/50”, high pressure laminate, medium density overlay or hard-
board. High pressure laminate 0.050” with cross-
band or 0.125”.
Warranty: Lifetime for interior use only.
Core/Edge Interface: Stiles and rails high frequency bonded to core and core assembly sanded prior to
application of crossband and veneer.
Crossband: 2 ply edge glued hardwood or One piece HDF (One piece HDF shown)
Faces: Selected hardwoods minimum 1/50”, high pressure laminate, medium density overlay or hard-
board. High pressure laminate 0.050” with cross-
band.
Warranty: Lifetime for interior use only.
Blocking (Reinforcement) Options: 5” (or as specified) for undercutting and special-ized hardware. Specify by number and dimen-sion desired.
Note 1: Any technological advancement made
by Georgia Pacific Corp. in Fire Stop I or II
is automatically included.
TECHNICAL DATA 745, 760, 790
Slam Cycle Over 1,000,000
Screw Holding 1030.4 lbs.
Split Resistance 847.9 lbs. average.
POSITIVE PRESSURE AND “S” LABEL COMPLIANCE ALL RATINGS
HB-1 HB-2 HB-4 HB-6 HB-8
5” TR 5”x10”
Blkg
5” BR
5”x18”
Blkg 5” Blkg
Category A and B, Doors and Jambs from the following options; Georgia Pacific FIREDOOR Components / ZERO International / PEMKO Manufacturing / Vancouver Door Company Inc. Testing.
INTUMESCENT FREE DESIGN ON 20 / 45 / 60 AND 90 MINUTE DOORS *** Any testing advancement by these companies will automatically be available to customers of Vancouver Door Company Inc. Contact our factory for updates on these systems.
20 Minute/45, 60, & 90 Minute approval to UBC Fire Test Standard 7-2, 1997
Now available 20 Minute Positive Pressure to 4’x9’ single and 8’x9’ Regular and double egress pairs. Series tested was 520P with 1-1/2” total hardwood laminated stiles.
745, 760 & 790 Mineral Core Fire Doors are available in Positive Pressure to 4’x8’ Singles and 8’x8’ regular and Double egress pairs.
Smoke and Draft Control Door Assemblies UBC 7-2 (1997) Section 7.210 Approval for supplemental “S” label. 20, 45, 60 and 90 Minute
20 Minute (metal frame) to 4’x9’ singles and 8x9’ regu-lar and double egress pairs. (Wood Frames) to 3’x9’ singles and 6’x9’ regular pairs. 45, 60, and 90 Minute Mineral Core Fire Doors to 4’x8’ singles and 8’x8’ regu-lar and double egress pairs. Total intumescent and edge sealing system including assembly installation instructions provided by VDC.
FIRE DOOR 745 Mineral Core 45, Minute Rated, See page 9
WDMA: FD-7 FD-5 AWS: FD-7 FD-5 WDMA: FD-HPDL AWS:FD-HPDL-5
Core: Georgia Pacific (proprietary) Mineral core .
Available Options for 745, 760 & 790
• Thickness, 1-3/4 only.
• STC rating of 35. May require additional
gasketing / seals.
• L.E.E.D. credits (See page 11)
• Vision lites, Metal kits supplied upon re-
quest. All glazing must comply with test approvals. Ask our tech department.
• Applied moldings. Limited to rating require-
ments and area limitations.
Page 4 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
ACOUSTICAL DOORS (STC) 800 Special Acoustical Core Veneer and High Pressure Laminate
WDMA: SR AWS: SR
Top and Bottom Horizontal edge: 1-1/2” top rail and 2-3/4” bottom rail minimum solid wood,
structural composite lumber or LVL.
Specialty Doors, Acoustical, X-Ray, Electro Shielding and Bullet Resistant.
Vertical Edge: 1-1/2” minimum hardwood; solid, laminated or veneered. Backer or inner ply
may be structural composite lumber or LVL.
Core: Acoustical material.
Crossband: 2 ply edge glued hardwood or one piece HDF. (2-ply shown)
Faces: Selected hardwoods minimum 1/50”, high pressure laminate or medium density overlay.
High pressure laminate 0.050” with cross band or
0.0125”.
Warranty: Five year warranty for interior use / one year exterior, fully Type 1 only, wood or
MDO faces only.
STC RATING
THICK MAX LIGHT OPENING
FIRE RATING
32 1-3/4 N/A 20 MIN.
35 1-3/4 N/A 45,60 & 90 MIN.
36 1-3/4 N/A
37 1-3/4 N/A
37 1-3/4 FULL LIGHT
37 1-3/4 lead lined N/A 20 MIN.
39 1-3/4 24X30
40 1-3/4 24X24 10X36
42 1-3/4 N/A
43 1-3/4 N/A
ACOUSTICAL RATINGS - ASTM E90 - 97 & 99
BULLET RESISTANT 650 Acoustical rating STC 37 Multiple ply ballistic fiberglass core
UL 752 -Level 3 Thru 5
STC TEST RESULTS AVAILABLE BY REQUEST.
LEAD LINED (X-RAY DOORS) 600XR Also Available 20 Minute Rated, See, page 9. Particle Core, Stave Lumber Core, Structural Acoustical Rating STC 37
WDMA: LL AWS: LL
Top and Bottom Horizontal edge: 1-1/4” solid wood or structural composite lumber, one piece or
laminated.
Vertical Edge: 1-1/2” minimum hardwood; solid, laminated or veneered. Backer or inner ply
may be structural composite lumber or LVL.
Core: Particleboard, ANSI A208,1, grade LD-1 or LD-2. Optional Stave core or SCLC also available..
Core/Edge Interface: Stiles and rails high fre-quency bonded to core and core assembly sanded
prior to application of lead, crossband and veneer.
Lead: Lead shielding is edge to edge under both faces.
Crossband: Edge glued or one piece crossband.
Faces: Selected hardwoods minimum 1/50”, high pressure laminate, medium density overlay or hard-
board. High pressure laminate 0.050” with cross-
band or 0.125”.
Warranty: Lifetime for interior use.
Electro Shielding doors are constructed similar to X-Ray
Lead Thickness Lbs. per sq. ft.
1/16” 4 (Typical) 1/8” 8 1/4” 16
Available Options for 800, 600 & 650. Many of the same options listed for the “Solid Core” products also apply to the products listed on this page. Check with our sales or technical departments.
Top and Bottom Horizontal edge: 1” solid hard-wood .
Vertical Edge: 3/4” minimum solid hardwood and or structural composite lumber or LVL.
Core/Edge Interface: Stiles and rails high fre-quency bonded to core assembly then sanded prior
to application of crossband and veneer.
Faces: Selected hardwoods minimum 1/50”, high pressure laminate, medium density overlay or hard-
board. High pressure laminate 0.050” with cross-
band or 0.125”.
Warranty: Lifetime for interior use only.
Page 5 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Hollow Core, Bifolds and Sliders
STANDARD HOLLOW CORE 310 Honeycomb Core. WDMA: SHC-7 AWS: SHC-7 WDMA: SHC-HPDL
Top and Bottom Horizontal edge: 1-1/8” minimum solid wood, medium density fiberboard or
structural composite lumber, one piece or laminated.
Vertical Edge: 1” minimum solid, laminated or veneered wood. Backer or inner ply may be struc-
tural composite lumber or LVL.
Core: Honeycomb fully expanded to all edges.
Bonding: Vertical edges and rails not bonded to core.
Crossband: Edge glued or one piece cross band.
Faces: Selected hardwoods minimum 1/50”,
High Pressure Decorative Laminate (HPDL)
NOT provided on Hollow Core doors.
Warranty: One year for interior use. 0nly!
Blocking (Reinforcement) Options: Specify by number and dimension desired.
INSTITUTIONAL HOLLOW CORE 510 Honeycomb Core. 2 lock blocks & Intermediate rail included. WDMA: IHC-7 AWS: IHC-7 WDMA: IHC-HPDL
Top and Bottom Horizontal edge: 6-1/2” solid wood, medium density fiberboard or structural
composite lumber, one piece or laminated.
Vertical Edge: 2-1/2” minimum solid, laminated or veneered wood. Backer or inner ply may be structural
composite lumber.
Core: Honeycomb fully expanded to edges.
Bonding: Vertical edges and rails not bonded to core.
Crossband: Edge glued or one piece crossband.
Faces: Selected hardwoods minimum 1/50”, high pressure laminate, medium density overlay
or hardboard. High pressure laminate 0.050” with
crossband or 0.125”.
Warranty: One year for interior use only.
HB-1 HB-3 HB-4 HB-5 HB-7
5” TR 5” BR
5”x18”
Blkg 5” Blkg 5”x5”
Hook
Block
BIFOLD (FOLDING) UNITS, 2 & 4 DOOR Hollow Core & Solid Core. (Non rated) Veneer, HDF, MDO and High Pressure Laminate. 1-3/8” - 1-3/4” thicknesses. Heavy Duty hardware supplied upon request.
2 & 4 Door Bifold unit
SLIDERS, POCKET DOORS & PANELS Hollow Core & Solid Core. (Non rated) Matching Veneer, HDF, MDO and High Pressure Lami-nate. 1-3/8” - 1-3/4” thicknesses.
2 & 4 Door sliders.
Available Options:
• LEED Credits (Solid core doors only).
• Vision lite and Louver cut outs.
• Quirks, grooves and inlays.
• Hardware preparation.
Warranty: Lifetime Interior use only
Page 6 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Special Services and Products.
Vancouver Door Company’s many custom services reduce job site costs and assist in meeting time requirements on special installations.
DOORS & TRANSOMSDOORS & TRANSOMSDOORS & TRANSOMSDOORS & TRANSOMS
DUTCH DOORS DUTCH DOORS DUTCH DOORS DUTCH DOORS
Veneers may be continuous match, end match or no match. (End matched shown) See WDMA: I.S. 1-A, Section A-6 Rabetted meeting rails are optional. Not approved for STC applications.
Available non-rated and 20, 45, 60, and 90 minute rated. See pages 9 & 10. Check with our sales or tech department for details & options.
Dutch doors are utilized in applications where the upper half of the door may be opened while keeping the lower half closed. Both leaves are typically latched together to maintain a single opening. Dutch door shelves on one side only or on both sides of the door. All shelves are sent loose for field installa-tion. Available non-rated and 20, 45 or 60 minute rated. See pages 9 & 10. Check with our sales or tech department for details & options
WICKET DOORSWICKET DOORSWICKET DOORSWICKET DOORS
Wicket doors are utilized in applications where only a portion of the door opening needs to be accessible. They consist of the primary door and the wicket insert which can be opened to allow access while keeping the primary door closed / locked. Faces are matched so that the wicket door matches the face on the primary door. Wicket doors are attached with continu-ous or concealed hinges and can be latched with standard lock prep. Not approved for fire rated applications. Not approved for STC rated applications.
DOORS w/ VISION LITESDOORS w/ VISION LITESDOORS w/ VISION LITESDOORS w/ VISION LITES
Vision lites can be provided in many differ-ent configurations and sizes. We can provide stop and glass. Factory glazing is available as well.
Available non-rated and 20, 45, 60, and 90 minute rated. See pages 9 & 10. Check with our sales or tech department
LOUVER DOORSLOUVER DOORSLOUVER DOORSLOUVER DOORS
Variable size and type louvers can be provided and installed at the factory. From small to half to full size louvers. Great for providing pass through Ventilation and fresh air. Chevron style louvers are available in most hardwoods.
Available non-rated and 45, 60, and 90 minute rated. See pages 9 &10. Not approved for 20 minute!
INLAYS, QUIRKS, APPLIED MOLDING.INLAYS, QUIRKS, APPLIED MOLDING.INLAYS, QUIRKS, APPLIED MOLDING.INLAYS, QUIRKS, APPLIED MOLDING.
Inlays, Quirks (grooves), Applied molding can be provided in many different configu-rations and sizes based on your specifica-tions.
Available non-rated and 20, 45, 60, and 90 minute rated. See pages 9 & 10.
Page 7 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Standard bead stop
Typical molding profiles
Special Services—continued
SKETCH FACESKETCH FACESKETCH FACESKETCH FACE
Various configurations based on any given design and veneer species.
STILE and RAIL STILE and RAIL STILE and RAIL STILE and RAIL
Wood doors in various species, sizes, configurations and fire ratings.
FACTORY PREFINISHINGFACTORY PREFINISHINGFACTORY PREFINISHINGFACTORY PREFINISHING
The controlled application process in factory prefinishing assures top quality finishes with maximum durability not possible with site applied coatings. See WDMA I.S. 1-A, Section F-1 through F-7.
PRESERVATIVE / INSECT TREATMENTPRESERVATIVE / INSECT TREATMENTPRESERVATIVE / INSECT TREATMENTPRESERVATIVE / INSECT TREATMENT
Available on request.
EDGE OPTIONSEDGE OPTIONSEDGE OPTIONSEDGE OPTIONS
Prefitting and edge beveling. Radius edges. Edge rabbeting. Veneered or plastic laminate edges to match faces.
FACTORY MACHININGFACTORY MACHININGFACTORY MACHININGFACTORY MACHINING
Doors can be prepared for any standard or custom hardware. Precision factory machining and pre-fitting ensure proper hardware preparation for tolerances specified by National Fire Protection Association (NFPA), the Architectural Woodwork Standards (AWS), the Window and Door Manufacturers Association (WDMA) and the Door and Hardware Institute (DHI).
Some of our machining options include:
• Concealed Vertical Rods (Less Bottom Rod—LBR)
• Raceway’s (Wire-chases)
• Concealed hinges, Anchor hinges, Pivot hinges.
• Mortised door bottoms
• Mortised edge guards
Our expert staff can coordinate your projects to ensure a smooth installation of hardware to doors.
WOOD JAMBSWOOD JAMBSWOOD JAMBSWOOD JAMBS
Wood and wood veneered jambs in many species side light jambs are also available. Available non-rated, 20 to 90 minute rated. Positive Pressure “S” label available in 20 to 90 minute singles and pairs. 20 minute rated wood jambs in sizes up to 4’x9’ singles and 8’x9’ pairs.
PARTITIONS, WALL PANELS & DESK TOPS.PARTITIONS, WALL PANELS & DESK TOPS.PARTITIONS, WALL PANELS & DESK TOPS.PARTITIONS, WALL PANELS & DESK TOPS.
Provided in any specie veneer and plastic laminate. Sizes up to 4’x10’ in 1” to 1-3/4” thick with edge banding to match or as specified.
Page 8 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Concealed overhead closer w/ fire shield for rated doors
RatingsRatingsRatingsRatings
20 Minute20 Minute20 Minute20 Minute 45 Minute45 Minute45 Minute45 Minute
Swing Door and tran-som
Pair Regular or Double Egress
Lead Lined Single Swing
Single Swing, Door and Tran-som
Pair Regular or Double Egress
Positive Pressure “5” Label
Yes* Yes* Yes* Yes* Yes*
Sizes
4’x10’ Single
4’x10’ DR/TR
Max TR 4’x2
Or 3’x3’
Up o 8’x9’
6’x10’
8’x9’ DE
4’x9’
4’x10’
3’x10’ DR/TR
Max TR 3’x3’
6’x7’ Note: 6
8’x8’ Reg/DE
8’x9’ CVRE
Protection Plates 48”x48” 48”x48” 48”x48” 48”x48” Note: 2 48”x48” Note: 2
EPT Yes Yes Yes Yes Note: 2 Yes Note: 2
Wire Chase Yes Yes Yes Yes Yes
Dutch Door 4’x8’
No Vision Panel
N/A N/A 4’x8’
No Vision Panel
N/A
Maximum Louver Fusible Link
N/A N/A N/A 24”x24” 24”X24’ each leaf
Viewers Up to 1” diameter Up to 1” diameter N/A Up to 1” diameter Up to 1” diameter
Hinges Per NFPA #80 Per NFPA #80 Per NFPA #80 Per NFPA #80
Note: 7
Per NFPA #80
Note: 7
Locks Cylindrical / unit /
mortise
Cylindrical / unit /
mortise
Cylindrical / unit /
mortise
Cylindrical / unit / mortise Cylindrical / unit / mortise
Exit Devices Listed rim, mortise
or vertical rod
Listed rim, mortise or
vertical rod
Listed rim, mortise
or vertical rod
Listed rim, mortise or
vertical rod
Listed rim, mortise or
vertical rod
Flush Bolts Top/Bottom for Inactive Leafs
N/A
Listed surface manual
or automatic flush
bolts installed with 28
gauge liner
N/A
N/A
Listed surface manual or
automatic flush bolts
installed with 28 gauge
liner
Edge Guards Yes Note: 3 Yes Note: 3 Yes Note: 3 Yes Note: 3 Yes Note: 3
Concealed Vertical Rod
Yes Yes, no channel
required
N/A Yes, 5”channel may be
required
Yes, 5” channel may be
required
Concealed Closers Yes Yes N/A Yes Note: 2 Yes Note: 2
Applied Moldings Yes Yes No Yes Yes
Automatic Door Bottoms
Yes Yes N/A Yes Note: 2 Yes note: 2
Maximum Vision Panel
1,296 sq. in.
36” Wide
54” High
1,296 sq. in.
36” Wide
54” High
N/A
1,296 sq. in.
2,638 sq. in. Note: 1
1,296 sq. in.
2,638 sq. in. Note: 1
Fire Rated Doors - Single Swing and Pairs
Note: (1) Special glass and stop required/max size 36”x80”. (2) Special blocking required. (3) Special edges required. (4) Special glass and stop required.
(5) Special blocking required. (6) No astragal required with special blocking.
(7) Special hinges and pivots require additional blocking.
*Contact factory for maximum sizes and options for Neutral and Positive Pressure requirements.
Page 9 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Fire Rated Doors - Single Swing and Pairs
Testing: Labeled fire doors have been tested in accordance with UL 10(B), CAN 4S 104(ULC-S104), NFPA 252 and UBC 7-2 fire door test standards.
Labeling: Testing, inspection and labeling is by Intertek Testing Ser-vices/Warnock Hersey, Inc. Vancouver Door Co. is listed to manufac-ture and machine fire rated wood doors. Labels are affixed to hinge edge at eye level, or on top rail if positive pressure.
RatingsRatingsRatingsRatings
60 Minute60 Minute60 Minute60 Minute 90 Minute90 Minute90 Minute90 Minute
Single Swing, Door and Transom
Pair Regular or Double Egress
Single Swing, Door and Transom
Pair Regular or Dou-ble Egress
Positive Pressure “5” Label
Yes* Yes* Yes* Yes*
Sizes
4’x10’
3’x10’ DR/TR
Max TR 3’x3’
6’x7’ Note: 6
8’x8’ Regular/DE
8’x9’ CVRE
4’x10’
3’x10’ DR/TR
Max TR 3’x3’
6’x7’ Note: 6
8’x8’ Regular/DE Note: 8
8’x9’ CVRE
Protection Plates 48”x48” Note: 5
page 9
48”x48” Note: 5 page 9 48”x48” Note: 5 page 9 48”x48” Note: 5 page 9
EPT Yes Note: 2 page 9 Yes Note: 2 page 9 Yes Note: 2 page 9 Yes Note: 2 page 9
Wire Chase Yes Yes Yes Yes
Dutch Door 4’x8”
No Vision Panel
N/A N/A N/A
Maximum Vision Panel
100 sq. in.
1015 sq. in. Note: 4
page 9
100 sq. in.
1015 sq. in. Note: 4
page 9
100 sq. in.
1015 sq. in. Note: 4 page 9
100 sq. in.
1015 sq. in. Note: 4 page 9
Maximum Louver Fusible Link
24”x24” 24”x24” each leaf 24”x24” 24”x24” each leaf
Viewers Up to 1” diameter Up to 1” diameter Up to 1” diameter Up to 1” diameter
Hinges Per NFPA #80 Note:
7 page 9
Per NFPA #80 Note: 7
page 9
Per NFPA #80 Note: 7 page 9 Per NFPA #80 Note: 7 page 9
Locks Cylindrical / unit /
mortise
Cylindrical / unit / mor-
tise
Cylindrical / unit / mortise Cylindrical / unit / mortise
Exit Devices Listed rim, mortise or
vertical rod
Listed rim, mortise or
vertical rod
Listed rim, mortise or vertical
rod
Listed rim, mortise or vertical
rod
Flush Bolts Top/Bottom for Inactive Leafs
N/A
Listed surface manual or
automatic flush bolts
N/A
Listed surface manual or
automatic flush bolts installed
Edge Guards Yes Note: 3, page 9 Yes Note: 3 page 9 Yes Note: 3 page 9 Yes Note: 3 page 9
Concealed Vertical Rod
Yes, 5” channel may
be required.
Yes, 5” channel may be
required
Yes, 5” channel may be
required
Yes, 5” channel may be
required
Concealed Closers Yes Note: 2 page 9 Yes Note: 2 page 9 Yes Note: 2 page 9 Yes Note: 2 page 9
Applied Moldings Yes Yes Yes Yes
Automatic Door Bot-toms
Yes Note: 2 page 9 Yes Note: 2 page 9 Yes Note: 2 page 9 Yes Note: 2 page 9
Page 9 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Matrix for LEED Credit ContributionsMatrix for LEED Credit Contributions Developed by the U/S Green Building Council (USGBC), Leadership in Energy and Environmental Design (LEED) provides building owners and operators a concise framework for identifying and implementing practical and meas-urable green building design, construction, operations and maintenance solutions. The matrix below identifies the wood doors (Veneered and laminated faces) that qualify for credits for a specific project. All LEED projects must be specified when submitting a quote request or a purchase order to ensure that you obtain the necessary contributions from the doors. Please feel free to contact us with any questions or if you need additional information. 1-800-999-3667
Product Type (Wood & HPDL Faces)
MR 4.1
MR 4.2
MR 5.1
MR 5.2
MR 6
MR 7
EQ 4.4
310 - Hollow Core (HC) Yes Yes No No No No No
510 - Institutional Hollow Core (IHC) Yes Yes No No No No No
520P - Particle Core (PC) Yes Yes No No No Yes Yes
520A - Agrifiber Core (AC) No No No No Yes Yes Yes
520S - (SLC) No No No No No Yes Yes
520C - (SCLC) Yes Yes No No No No Yes
600P - Lead Lined (LLPC) Yes Yes No No No Yes Yes
600S - Lead Lined (LLSLC) No No No No No Yes Yes
600C - Lead Lined (LLSCLC) Yes Yes No No No No Yes
650P - Bullet Core (BCPC) Yes Yes No No No Yes Yes
745M - Mineral Core (MC45) Yes Yes No No No Yes Yes
760M - Mineral Core (MC60) Yes Yes No No No Yes Yes
790M - Mineral Core (MC90) Yes Yes No No No Yes Yes
836 - Sound Transmission Class (STC36) Yes Yes No No No Yes Yes
839 - Sound Transmission Class (STC39) Yes Yes No No No Yes Yes
840 - Sound Transmission Class (STC40) Yes Yes No No No No No
841 - Sound Transmission Class (STC42) Yes Yes No No No No No
843 - Sound Transmission Class (STC43) Yes Yes No No No No No
MR 4.1 Recycled Content: 10% (Post Consumer + 1/2 PreMR 4.1 Recycled Content: 10% (Post Consumer + 1/2 PreMR 4.1 Recycled Content: 10% (Post Consumer + 1/2 PreMR 4.1 Recycled Content: 10% (Post Consumer + 1/2 Pre----Consumer) Consumer) Consumer) Consumer)
MR 4.2 Recycled Content: 20% (Post Consumer + 1/2 PreMR 4.2 Recycled Content: 20% (Post Consumer + 1/2 PreMR 4.2 Recycled Content: 20% (Post Consumer + 1/2 PreMR 4.2 Recycled Content: 20% (Post Consumer + 1/2 Pre----Consumer)Consumer)Consumer)Consumer)
MR 5.1:Regional Materials: 10% Extracted, Processed & Manufactured RegionallyMR 5.1:Regional Materials: 10% Extracted, Processed & Manufactured RegionallyMR 5.1:Regional Materials: 10% Extracted, Processed & Manufactured RegionallyMR 5.1:Regional Materials: 10% Extracted, Processed & Manufactured Regionally
MR 5.2 Regional Materials: 20% Extracted, Processed & Manufactured RegionallyMR 5.2 Regional Materials: 20% Extracted, Processed & Manufactured RegionallyMR 5.2 Regional Materials: 20% Extracted, Processed & Manufactured RegionallyMR 5.2 Regional Materials: 20% Extracted, Processed & Manufactured Regionally
MR 6: Rapidly Renewable MaterialsMR 6: Rapidly Renewable MaterialsMR 6: Rapidly Renewable MaterialsMR 6: Rapidly Renewable Materials
MR7: Certified WoodMR7: Certified WoodMR7: Certified WoodMR7: Certified Wood EQ 4.4: LowEQ 4.4: LowEQ 4.4: LowEQ 4.4: Low----Emitting Materials Emitting Materials Emitting Materials Emitting Materials ---- No Added Urea Formaldehyde (NAUF)No Added Urea Formaldehyde (NAUF)No Added Urea Formaldehyde (NAUF)No Added Urea Formaldehyde (NAUF)
Page 11 Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
All Vancouver Door products are in compliance with California Air Resource Board (CARB) Phase 2 requirements.
Vancouver Door Company, Puyallup WA. 1-800-999-3667 www.vancouverdoorco.com
Pan Pacific Hotel Seattle Zebrawood
Fort Harrison Hotel Clearwater, FL
Panorama Towers, LV, Nevada
Lourdes Hospital