ValVue ESD Standalone ESD PRM Plug-In Quick Start Guide v1 Pozisyonerler/Valvue ESD/Valvue... ·...

1 www.dresser.com 1

Quick Start Guidev1.0

ValVue® Suite• ValVue® ESD Standalone• ValVue® ESD PRM Plug-In

ValVue® ESD

Valve Interface Portal

2 www.dresser.com 1 2 www.dresser.com 1


PrefaceThis booklet is a guide for selecting, installing and executing the ValVue® ESD application as well as verifying that the destination computer satisfies the installation requirements.

For support and questions about this product, contact your nearest Masoneilan® representative (locations can be found at www.masoneilan.com) or email your technical support inquiries to [email protected]

Thank you for choosing Masoneilan’s safety solutions.

Sandro Esposito

Product Marketing Manager – Smarts Products Dresser Masoneilan

www.masoneilan.com


ContentsIntroduction ...........................................................................................3

Installation Requirements ......................................................................4

Hardware .......................................................................................4

Software .........................................................................................4

Installing the Applications .....................................................................5

Installing ValVue® ESD Standalone ................................................5

Installing the PRM Related Applications ........................................7

Installing Central ValVue ESD ................................................7

Installing PRM PLUG-IN ValVue ESD....................................10

PRM Setup Requirements ....................................................................12

How to Associate Plug-in with Device ........................................12

How to Associate the SVI II ESD Icon with the SVI II ESD Device ..13

Launching the Applications .................................................................14

Launching ValVue ESD Standalone ..............................................14

Launching PRM Central ValVue ESD ............................................15

Launching PRM PLUG-IN ValVue ESD ..........................................18

Startup of an SVI II ESD .......................................................................18

Calibrating ....................................................................................18

Partial Stroke Test ........................................................................19

Settings ................................................................................19

Launching a PST ...................................................................21

Viewing a PST and its Results ..............................................22

On-Line Help .......................................................................................23

PLUG-IN ValVue ESD Warnings ...................................................23

PRM Multi-Server .................................................................23

PRM PLUG-IN ValVue ESD Installation Folder .....................23

Appendix .............................................................................................24


IntroductionThe ValVue® ESD family contains three applications, ValVue ESD, PRM Central ValVue ESD, PRM PLUG-IN ValVue ESD and ESDVue which is a common library.

Standalone editionThe standalone application connects directly to one or more devices through a HART® modem or a MTL Multiplexer network.

Yokogawa PRM PLUG-IN editionFirst, the application consists of the PRM Central ValVue ESD. It is the ValVue ESD service that monitors all registered Masoneilan®, type 203 devices (SVI® II ESD) known by the PRM server. It automatically retrieves and saves the Partial Stroke Tests (PST) results for all devices to the ValVue ESD central database. This functionality ensures the results in the database are logged no matter how the PST test is triggered (locally, remotely, schedule, handheld, analog, etc). It also provides for a snap-shot of the PST schedules and health of all SVI II ESD devices.

PRM PLUG-IN ValVue ESDThis is the ValVue ESD application that will launch as the PLUG-IN for Masoneilan’s SVI II ESD device (type 203) from the PRM UI. It also provides for a snap-shot of the PST schedules and health of all SVI II ESD devices.

ESDVueThis is the user friendly dialog (or session) that is launched from ValVue ESD (PLUG-IN or standalone). It allows the user to access all HART features available from the device including status, diagnostics, configuration, calibration, etc. It also allows the user to access and graph historical data saved to the database for all devices contained in the database.


Installation Requirements

Hardware Processor: PC with minimum 1 GHz Intel Pentium or compatible RAM: minimum 1gig Disk: Depends on product

Product Application Component

Database Component

Total Installation Size

ValVue® ESD 15M 30M minimum* 45M

PRM Central

ValVue ESD

15M 30M minimum* 45M

PRM PLUG-IN

ValVue ESD

15M N/A 15M

*Assuming 100 devices, 1 PST/month for 5 years

Software OS: Windows XP SP2

Window Server 2003 with Service Pack 1 or Window Server 2003 R2

PRM: PRM R3.x

Note: PRM is NOT required for standalone installations.


Installing the ApplicationsFigure 1 shows the installation browser for ValVue ESD. The browser allows you to install each one of the applications that comprise the ValVue ESD family and to view documentation for the products and other helpful information. If you wish to connect your computer to a device directly through a HART® modem or MTL Multiplexer, then install the standalone version. If you wish to integrate ValVue ESD with PRM and connect to devices using the PRM PLUG-IN, then install the PLUG-IN client on your computer. Integration with the PRM system also requires installation of the PRM Central ValVue ESD for each PRM server in the system. The following sections provide instructions for the installation of each one of the applications.

Figure 1 ValVue ESD Installation Browser

Installing ValVue® ESD StandaloneClick on Install Standalone Edition on the installation browser to begin installing ValVue ESD Standalone. The first dialog box where you will be asked to make a decision is for the installation folder shown in Figure 2. If you prefer not to use the default, click on Change to select a different one. That will bring up the file browser shown in Figure 3. You may select any path from the file browser or enter the path directly. If the specified folder does not exist, it will be created for you. There are no disadvantages for the location of this installation folder.


Figure 2 Choose Standalone Destination Location

Figure 3 Choose Standalone Folder


Installing the PRM related applicationsTo install the PRM related applications click on Yokogawa PRM Edition on the installation browser. This will show the PRM installation browser shown in Figure 4. Typically, PRM Central ValVue ESD will be used to monitor all devices while PLUG-IN ValVue ESD will be used to access the functionality of the device.

Figure 4 PRM ValVue ESD Installation Browser

Installing Central ValVue® ESD

This application should be installed on each PRM server in the control system, preferably the server machine. Click on Install Central Server on the PRM installation browser to begin installing Central ValVue ESD. The first dialog box where you will be asked to make a decision is for the installation folder shown in Figure 5. If you prefer not to use the default, click on Change to select a different one. That will bring up the file browser shown in Figure 6. You may select any path from the file browser or enter the path directly. If the specified folder does not exist, it will be created for you. There are no disadvantages for the location of this installation folder.


Figure 5 Choose Central Destination Location

Figure 6 Choose Central Folder

Next you will be asked where to install the central database as shown in Figure 7. Again, if you prefer not to use the default, click on Change which will bring up the file browser shown in Figure 8. You may select any path from the file browser or enter the path directly. If the specified folder does not exist, it will be created for you. You should make a note of this machine name and folder share name, ValVue ESD DATABASE because it will be needed when installing PRM PLUG-IN ValVue ESD.


The installer will also create a data source for the database. If the database already exists, the installer will update the tables if necessary. No existing data will be lost.

Figure 7 Choose Database Destination Location

Figure 8 Choose Database Folder


Installing PRM PLUG-IN ValVue® ESD

This application should be installed on every computer on which PRM Client is installed after Central ValVue ESD has been installed for the particular PRM server. This application does not require registration. Click on Install PLUG-IN Client to begin installing PRM PLUG-IN ValVue ESD. The first dialog box where you will be asked to make a decision is for the installation folder shown in Figure 7. If you prefer not to use the default, click on Change to select a different one.

Figure 9 Choose PLUG-IN Destination Location

This will show the file browser shown in Figure 8. You may browse to the path or enter the path directly; regardless, the path must be the same for all PRM PLUG-IN ValVue ESD installations. Note that if you assign the installation to a different path from the previous installs, including drive, PRM PLUG-IN ValVue ESD will no longer launch from the previous computers unless the full path is accessible from the previous computers.


Figure 10 Choose PLUG-IN Folder

Next you will be asked to locate the central database that was installed with Central ValVue ESD. In the dialog box if the location shown is not correct as is shown in Figure 11, click on Change and locate the location of the database using the file browser or enter it directly. Figure 12 shows the file browser. The name of the shared folder is ValVue ESD DATABASE.

Figure 11 Choose Central Database Location


Figure 12 Choose Shared Database Folder

The installer will automatically register the PRM PLUG-IN ValVue ESD within PRM.

PRM setup requirementsIn order to finalize the integration of ValVue ESD with PRM, a few manual steps must be performed as outlined in this section.

How to associate plug-in with deviceThough the installer for the PRM PLUG-IN ValVue ESD will automatically register the plug-in with PRM, the SVI II ESD devices must be associated with this plug-in. This is accomplished manually. To associate the plug-in, start the PRM client from any machine on which PLUG-In ValVue ESD was installed and perform the following for each SVI II ESD device in the PRM system:

Double-click a SVI II ESD device (identified by •Vendor=Masoneilan, Model=Device_203) in the PRM user interface


Select • Plug-In from the toolbar that appears on the next screen

Right click in the Plug-In Name window and select • Add from the resulting popup menu

Select • PRM PLUG-IN ValVue ESD from the list of plug-in names that appear

How to associate the SVI II® ESD icon with the SVI II ESD deviceThe Masoneilan® SVI II ESD icon looks like that shown in Figure 13. If this icon does not appear in your PRM tree view, it must be assigned manually.

Figure 13 SVI2ESD_ICON

To assign the icon, start PRM client from any machine on which PLUG-IN ValVue ESD was installed and perform the following once:

Register the device icon•

- From the main menu select Register/Master Data/Register Device Icon

- From the Device Icon List screen select Add

- Enter the following parameters in the form:

Location of image file: ValVue ESD install directory/•Icons/SVI II ESD.bmp

Icon ID: • SVI II ESD

Description: • Masoneilan SVI II ESD


Assign the registered icon with the device•

- From the main menu select Register/Master Data/Register Assign Icon

- From the Assignment of Device Icons screen select Add

Enter the following parameters in the form:•

- Vendor: Masoneilan

- Model: Device_203

- Sub Model: blank

- Icon: select the icon you registered

You should now see the icon appear for all Masoneilan, Device_203 devices in the display.

Launching the Applications

Launching ValVue® ESD Standalone To launch ValVue ESD Standalone simply double-click the ValVue ESD icon installed on the desktop. The application requires separate registration on each computer on which it is installed, but comes with a free, fully functional 60-day trial period. Until the application is registered, the dialog box shown in Figure 14 will appear when the application is started. Enter the information to register. Just hit enter to run unregistered. A dialog box will appear to inform you how many days are left on the trial period as shown in Figure 15. At the end of the trial period the application will no longer run without registering.


Figure 14 Standalone Registration Dialog

Figure 15 Standalone Trial Period Information

ValVue ESD Standalone comes configured for a HART® modem connected to COM1. If your configuration differs from this, you will need to change the ValVue ESD options. The connection options can be changed by selecting Tools/Set Options from the main menu. Please note that it may take several seconds for ValVue ESD to resolve that there is no device present if this is the incorrect configuration because of the wait time and retries that ValVue® ESD employs to ensure reli-able HART® communication.

If ValVue ESD connects with a device, it will include it in the device list. Selecting this device from the list or double-clicking on it will launch ESDVue and allow you to view and initiate all the features provided by the SVI® II ESD and ValVue ESD.


Launching PRM Central ValVue ESDPRM Central ValVue ESD is intended to run as a service on the PRM server machine, but it can be launched directly by double-clicking the PRM Central ValVue ESD icon that was installed on the desktop. (The application will prevent more than one instance from running on the computer.) The service will start automatically after the computer restarts. PRM Central ValVue ESD requires registration to run, but comes with a free, fully functional 60-day trial period. Until the application is registered, the dialog box shown in Figure 16 will appear when the application is started whether as service or from the desktop. Enter the information to register or just hit enter to run unregistered. A dialog box will appear to inform you how many days are left on the trial period as shown in Figure 17. At the end of the trial period the application will no longer run without registering.

Figure 16 Central Registration Dialog


Figure 17 Central Trial Period Information

When launched as a service, its icon, shown in Figure 18, will appear in the system tray. Double-click on the icon to see the ValVue® ESD user interface. Note, that when there is no activity in the user interface for some period, the Central ValVue ESD will return to the tray. Also, if you exit the application launched as a service, it will restart automatically. To disable this feature just stop the service called XMnCloSvr using the Windows Services Management tool.

Figure 18 PRM Central ValVue ESD Service Icon

Using the PIA API, the application will list all devices known to the PRM server to which it is connected. By default it searches the path: CLASS:PLANT\HART\MASONEILAN. A separate license is required to monitor devices. The application comes with a free license to monitor 5 devices for a 60-day trial period. At the end of the trial period PRM Central ValVue ESD will no longer monitor the devices unless licensed.

Regardless of the license, the application will support all Masoneilan® Device Type 203 devices that it finds in the device list; however, those devices not covered by the license will show an icon to indicate that the device is not monitored. View the on-line help for more information about the icons that can show in the device list. Launch ESDVue to access all the features available from the device and run diagnostics for a selected valve. To do so, simply double-click on the desired valve in the valve list or select it and click on the Select button.


Launching PRM PLUG-IN ValVue ESDPRM PLUG-IN ValVue ESD is launched from the PRM client user interface once it has been registered in the PRM and associated with a specific device as explained above. The PRM Central ValVue ESD associated with the PRM server must be running. Executing the plug-in, launches PRM PLUG-IN ValVue ESD. This automatically launches ESDVue for the selected device, provided that PRM Central ValVue ESD has been licensed for that device. The licensing restrictions described above for PRM Central ValVue ESD also apply to PRM PLUG-IN ValVue ESD. After ESDVue is exited, ESDVue can be launched for another licensed device in the device list.

Startup of an SVI® II ESD

CalibratingIf the unit was pre-installed on an actuator, it is not necessary to perform any calibrations. Proceed to the section PST to configure the device to conduct a partial stroke test. Otherwise proceed as follows:

All precautions per the Quick Start Guide QS5000 must be 1. adhered to.

Per the Quick Start Guide QS5000, install the SVI II ESD on 2. the actuator and apply electrical and air supply.

Launch an ESDVue session with the connected device and go 3. to the calibrate page.

Set the mode to SETUP using the MODE button located on 4. the bottom of the user interface.

Click on TOOLS -> Find Valve Stops. This procedure will fill 5. and exhaust the actuator chamber and measure the mechanical travel. This procedure will take approximately 1 minute.


Click on TOOLS -> AUTOTUNE. This procedure will determine 6. the tuning parameters that will be utilized to move the valve during a PST test. The values are also utilized when the SVI II ESD positions the ESD Valve in the MANUAL mode. This procedure will take approximately 3-5 minutes and may take as much as 8 minutes. If the procedure fails, click on TOOLS -> RESET TO DEFAULT to utilize the default values.

Set the mode back to NORMAL.7.

Partial Stroke Test

Settings

The settings can be modified in the NORMAL and 1. SETUP Mode.

The PST settings are described in the On-Line Help. For your 2. convenience here’s a summary of the parameters:

PST Travel – The allowed valve movement from full Open •position in percentage of travel. A typical value is 20%. Maximum allowed is 30%. The greater the travel range, the more accurate the results from the PST Test.

Minimum Pressure – The allowed reduction in pressure in •the actuator to achieve the desired PST Travel. This value depends on the spring range and the valve/actuator hysterisis. To set this value, first, run an Extended Actua-tor signature from the DIAGNOSTICS PAGE. Then, locate on the Y-Axis of the signature, the X-Axis pressure value for the desired Travel target. For example, if the PST Travel is 30%, what is the pressure value to reach 70% travel. The Y-value selected must be on the upper curve of the graph.


Maximum Time – The allowed amount of time in seconds •before the PST test aborts. This value can be determined as follows:

- Maximum Time = (Travel Range * 2 * PST Speed ) + Dwell Time + 5 seconds.

PST Speed – The valve Travel speed in % Travel •per second.

Dwell Time – The amount of time in seconds between •the down ramp and the up ramp of valve stroke.

Friction Low Limit – The alarm threshold for low friction. •This alarm is set if the analyzed friction from the PST test is less than this value. Engineering units of pressure (PSI, kPa or BAR).

Friction High Limit – The alarm threshold for high friction. •This alarm is set if the analyzed friction from the PST test is more than this value. Engineering units of pressure (PSI, kPa or BAR).

Breakout Limit – The alarm threshold for valve breakout •force (force to initiate valve movement). This alarm is set if the analyzed friction from the PST test is more than this value. Engineering units of pressure (PSI, kPa or BAR).

Droop Limit – The alarm threshold for air supply inlet •droop. This alarm is set if the analyzed Air Supply Droop from the PST test is more than this value, indicating a possible clogged up air filter in the air set or lack of volume feeding the SVI II ESD. Engineering units of pressure (PSI, kPa or BAR).


Freeze DO (Digital Output) – Enable for the DO2 (SW#2) •to not change state during a PST.

Freeze AO (Analog Output) – Enable for the built-in •positioner transmitter to not update its output value during a PST.

Enable Schedule – Enable to allow execution of the •Automated PST Schedules.

Upper SpringRange

PST Range

Breakout

MinimumAllowedActuatorPressure

During PST

Valve/ActuatorFriction/2

Launching a PSTIMPORTANT: A PST CAN ONLY BE LAUNCHED WITH THE SVI II ESD DEVICE IN NORMAL MODE

The SVI® II ESD offers several methods to launch a PST:

Using ValVue1. ® ESD (PST Page)


Using the local display/pushbutton2.

Using a HART3. ® handheld device with the SVI II ESD Device Descriptor (DD)

Using any HART host capable of DD services (such as 4. SDC-625) and loaded with the SVI II ESD Device Descriptor

Using the Automatic Scheduler (Calendar based, built-in the 5. SVI II ESD)

By setting the loop current to 16.4mA (77.5%). Available with 6. ASD models and A/DSD models.

Two PST’s can be stored in the non-volatile memory of the SVI II ESD. This allows for ValVue ESD to synchronize its database with the data in the field. When launching the PST from ValVue® ESD, the information will be automatically saved in the database at the end of the PST. If the PST is executed with the other methods described, the PST signature will remain in the non-volatile memory with a Flag indicating that ValVue ESD has not yet synchronized its database with the latest signature. The Flag will be lowered as soon as ValVue ESD connects to the device, or until the Central Lookout Service (PRM or Multiplexer operations only) scans the device. The signatures in the device are First In – First Out (FIFO).

Viewing a PST and its resultsTo view a PST:

From ValVue ESD, right-click on the device and select “View 1. Latest PST or Historical View.” From the Historical View, double-click on the X which indicates a dataset.

From ESDVue, go to the PST page and select the Diagnostic 2. To Load, then Click on Load Diagn.


On-Line HelpFor more information about getting started, click on the Help button located in the lower right corner of the ValVue ESD main screen. In fact help is available for every ValVue ESD and ESDVue dialog by simply clicking on the Help button or Help menu selection, depending on the dialog. The F1 key also provides help for most active dialogs.

PLUG-IN ValVue ESD warnings

PRM Multi-Server

Please note that because of the connection with the database and Central ValVue ESD, the Multi-Server switching feature, available on the PRM client, is not allowed.

PRM PLUG-IN ValVue ESD installation folder

As mentioned in installation instructions, the PLUG-IN ValVue ESD application must be installed to the same drive and folder on all machines which connect to the same PRM server.


AppendixDatabase storage requirements where the diagnostics use the typical setup parameters:

Basic database 350K bytes

Basic storage per device 20K bytes

Partial Stoke Test 1.2K bytes

Extended Signature diagnostics 2.7K bytes

Step diagnostics 4.2K bytes

For comments, feature request or any inquiries about ValVue ESD, send an email to [email protected]

P/N: 011526075-779 Rev. A

26 www.dresser.com 26

PN 011526075-779 Rev. A

ValVue ESD Standalone ESD PRM Plug-In Quick Start Guide v1 Pozisyonerler/Valvue ESD/Valvue... ·...

Documents

Transcript of ValVue ESD Standalone ESD PRM Plug-In Quick Start Guide v1 Pozisyonerler/Valvue ESD/Valvue... ·...